LAVAMAT 62800
Washing Machine
User information
Dear Customer,
Please read this user information carefully and keep it to refer to later.
Please pass the user information on to any future owner of the appliance.
The following symbols are used in the text:
1 Safety instructions
Warning! Information that affects your personal safety.
Important! Information that prevents damage to the appliance.
3 Useful tips and hints
2 Environmental information
2
Contents
Operating Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Description of the appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Control panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Programme overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Before the first wash. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Preparing and sorting washing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Running a wash cycle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Opening the door/loading washing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Adding detergent /conditioner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Switching on the appliance/selecting a programme . . . . . . . . . . . . . . . . . . . 12
Changing the spin speed/selecting rinse hold . . . . . . . . . . . . . . . . . . . . . . . . 13
Selecting additional programmes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
RINSE + . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
TIME SAVER. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
PRE WASH. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
STAIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Starting a programme. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Programme sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Interrupting a programme/adding washing . . . . . . . . . . . . . . . . . . . . . . . . . . 14
End of the wash cycle/removing the washing . . . . . . . . . . . . . . . . . . . . . . . . 15
Child safety device. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Cleaning and care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
What to do if.... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Remedying small faults yourself . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
If the wash result is not satisfactory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Carrying out an emergency drain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Drain pump. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Technical data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Consumption values. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
3
Installation and connection instructions. . . . . . . . . . . . . . . . . 24
Safety information concerning installation . . . . . . . . . . . . . . . . . . . . . . . . 24
Installing the appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Transporting the appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Removing the transit packaging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Where to install . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Making the appliance level. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Electrical Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Connecting the appliance to the water supply . . . . . . . . . . . . . . . . . . . . . 29
Water inlet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Water Drainage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Warranty conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Service and Spare Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
4
Operating Instructions
1 Safety
Prior to using the appliance for the first time
• Follow the “Installation and connection instructions”.
• If the appliance is delivered in the winter months when there are mi-
nus temperatures: store the washing machine at room temperature
for 24 hours before using for the first time.
Correct use
• The washing machine is only designed for the washing of normal domestic laundry at home.
• Additions or modifications to the washing machine are not permitted.
• Only use detergents/conditioners that are suitable for use in domestic
washing machines.
• The washing must not contain any flammable solvent. The risk of explosion exists.
• Do not use the washing machine for dry cleaning.
• Dyes/colour removers may only be used in the washing machine, if
the manufacturer of these products expressly permits this. We cannot
accept liability for any damage arising.
Child safety
• Keep packaging away from children. There is a risk of suffocation.
• Children often do not recognise the hazards associated with electrical
appliances. Don’t allow children to use the washing machine unsupervised.
• Make sure that children and pets don’t climb into the drum of the
washing machine. The risk of death exists.
General safety
• Repairs to the washing machine may only be carried out by qualified/
authorised service engineers.
• Never use the appliance when the electrical cable is damaged or the
control panel, worktop or plinth area are damaged to such an extent
that the inside of the appliance is openly accessible.
5
• Switch off the washing machine prior to cleaning it and carrying out
maintenance. In addition, remove the power plug from the power
point or – if the appliance has been hard-wired – switch off the cutout in the fuse box or completely remove the fuse.
• If operation is stopped, disconnect the appliance from the mains supply and turn off the tap.
• Never remove the power plug from the power point by pulling on the
cable. Always pull the plug.
• Multiway-plugs, connectors and extension cables must not be used.
Resulting overheating may constitute a fire hazard.
• Never wash the washing machine down with a water jet. Danger of
electric shock.
• When using wash programmes with high temperatures the glass in
the door will become hot. Do not touch it!
• Before emergency emptying of the appliance, before cleaning the
drain pump or opening the door in an emergency, let the water cool
down.
• Small animals can nibble on electrical cables and water hoses. This
can constitute a risk of electrocution and water damage. Keep small
animals away from the washing machine.
Disposal
Packaging material
2
The packaging materials are environmentally friendly and can be recycled. The plastic components are identified by markings, e.g. >PE<,
>PS<, etc. Please dispose of the packaging materials in the appropriate
container at your local waste disposal facilities.
2 Old appliance
Please dispose of your old appliance in line with the guidelines for disposal in your area.
1 Warning: When your appliance has finished its working life, remove
the plug from the mains socket. Cut off the cable and plug and dispose
of them.
Destroy the door lock. This prevents children from trapping themselves
inside and endangering their lives.
6
Description of the appliance
Detergent drawer
Rating plate
(behind door)
Screw feet
(height adjustable)
Control panel
Spin/RINSE HOLD button
Control panel
Plinth flap/
Drain pump
Multidisplay
Programme progress display
Additional programme
buttons
DOOR indicator
START/PAUSE button
Programme selector
7
Programme overview
Programme
ENERGY SAVING
2)
1)
6kg • • • • • •
Additional programmes Spin speed
(dry washing)
max. load
RINSE +
TIME SAVER
PRE WASH
STAIN
1200
RINSE HOLD
700
COTTONS/LINEN
95, 60, 50, 40, 30
EASY-CARES
60, 50, 40, 30, 20
DELICATES
40, 30
WOOL/ H (Hand-washing)
40, 30, COLD
6kg • • • •
3kg • • • •
3kg • • • • •
2kg • •
3)
• • •
3)
• •
RINSE 3kg • •
DRAIN -
SPIN 6kg • •
REFRESH 3kg • •
1) A 10 litre bucket contains approx. 2.5 kg dry washing (cotton)
2) Programme settings for tests in accordance with or in the style of EN 60 456 and IEC 60 456 are described in
the chapter “Consumption values”.
3) STAIN can only be set from 40°C upwards, as stain removal agent only becomes effective at higher temperatures.
8
Application/Features
Care
symbols
1)
Energy-saving programme which washes at 60 °C for lightly to normally soiled
whites or coloureds made of cotton/linen.
Programme for normally to heavily soiled whites/coloureds made of cotton/linen.
Programme for easy-care mixed fibres and synthetics.
Gentle programme for delicate textiles such as bonded fibres, micro-fibres, synthetics, net curtains (load max. 20 to 25 m
HOLD, also suitable for fabrics with climatic membranes, e.g. outdoor. clothing.
Specially gentle programme for machine and hand-washable wool/silk.
Separate gentle rinse (3 rinse cycles, liquid conditioner is washed in from the
compartment
Draining following a rinse hold.
Draining and spinning, e.g. following a rinse hold, or separate spinning of handwashed cottons/linen.
Special programme which washes at 30 °C, approx. 30 minutes, for brief washing
of e.g. worn-once, lightly soiled sports clothing or new clothes.
1) The figures in the care symbols indicate the maximum temperatures.
, gentle spin).
&
2
curtains). If used together with RINSE
M O
J M O
I K N
I K
Q L H
I K N
Q L
H
J M O
J M O
I K N
9
Before the first wash
1. Open the detergent drawer.
2. Pour approx. 1 litre of water through the detergent drawer into the
washing machine.
This closes the water container when the next programme is started
and the economy valve can function properly
3. To remove any production-related residues from the drum and water
tank, perform the first wash cycle without a load. Programme: COTTONS/LINEN 60, press the TIME SAVER button, add approx. 1/4 measuring cup of detergent.
Preparing and sorting washing
Preparing washing
• Empty the pockets. Remove foreign bodies (e.g. coins, paper clips,
nails, etc.).
• Do up zips, button up covers to prevent damage to washing.
• Remove the runners from net curtains or cover them with a net or a
bag.
• Wash delicate and small items in a net/pillowcase, e. g. net curtains,
tights, small socks, handkerchiefs, bras.
Important: Bras and other items containing wires should only be
washed in a net bag. The wires can work loose and damage the appliance.
10
Sorting washing
• By colour: Wash white and coloured washing separately. Washing can
run.
• By temperature, type of washing and care symbol.
Important: Do not wash fabrics with the G care symbol (= do not
wash!) in the washing machine.
Running a wash cycle
Opening the door/loading washing
1. Open the door: pull the handle on the door.
When the appliance is switched on, the DOOR and START/PAUSE indicators show whether the door can be opened:
DOOR indicator START/PAUSE indicator Can the door be opened?
illuminated green
illuminated green illuminated red
flashing red or not illumi-
nated
yes, after pressing the
START/PAUSE button
During the programme the door is locked when the water level or the
temperature is high. The DOOR indicator is not illuminated.
2. Separate washing and load it loosely.
Mix large and small items.
Important: Do not get any washing
caught between the door and the
rubber seal.
3. Firmly push the door shut. Door
catch must audibly click shut.
Adding detergent /conditioner
Important: Only use detergents/conditioners that are suitable for use in
household washing machines.
Add detergent/conditioner in accordance with the detergent/condition-
er manufacturer’s instructions. Observe instructions on the packaging.
The amount of detergent used depends on:
– the degree of soiling,
– the load size
– the hardness of the tap water.
• If the manufacturer does not make any recommendations with regard
to small volumes of washing: For a half-load use a third less, and for a
very small load use only the half the amount of detergent that is recommended for a full load.
• Water softener should be used from water hardness range 2 (=medi-
um). The amount of detergent used can then always be that as for
hardness range 1 (=soft). Your local water company will provide you
with information about water hardness in your area.
yes
11
1. Pull out the detergent drawer as far as it will go.
2. Add the detergent/conditioner.
3. Push the detergent drawer in fully.
Washing powder/tablets
for the main wash cycle
Conditioner/Wash-care
products to preserve the
shape of garments/Starch
Stain removal agent/
stain removal tablets
Washing powder/tablets
for the pre wash cycle
or water softener
Washing powder/tablets for the main wash cycle
If you are using water softener and require the right compartment for
detergent for the pre-wash cycle, add the water softener on top of the
detergent for the main wash cycle in the left compartment.
Softener, wash-care products to preserve the shape of garments,
starch
Fill the compartment to no more than the MAX indicator. Add water to
thick liquid concentrates in accordance with the manufacturer’s instructions before using them. Dissolve powder starch.
If you are using liquid detergent:
Add liquid detergent using measuring containers provided by the detergent manufacturer.
Switching on the appliance/selecting a programme
Set the programme and temperature using the programme selector.
3 The appliance is switched on by se-
lecting a programme.
– The programme progress display
shows the programme steps that
the selected programme will carry out.
– The estimated programme dura-
tion (in minutes) appears in the
multi-display.
12
Changing the spin speed/selecting rinse hold
The washing machine suggests the
maximum permitted spin speed
suitable for the selected programme. You can reduce this spin
speed:
To do this, press the Spin/RINSE
HOLD button repeatedly until the
required indicator is illuminated.
3 The spin speed for the final spin can be changed even during the pro-
gramme. To do this:
1. Press the START/PAUSE button.
2. Change the spin speed.
3. Press the START/PAUSE button again.
RINSE HOLD
With RINSE HOLD the washing is left to soak in the final rinse water. No
final spin takes place, only the intermediate spin. The intermediate spin
depends on the programme and cannot be changed.
Selecting additional programmes
If required, press additional programme button(s). The corresponding indicator will illuminate.
3 If “Err” flashes in the multi-display,
the selected additional programme
cannot be used together with the
wash programme set.
RINSE +
Two additional rinse cycles are carried out for the programmes ENERGY
SAVING, COTTONS/LINEN, EASY-CARES and DELICATES (for example in
cases of over-sensitive skin).
TIME SAVER
Shortened wash programme for lightly soiled items.
13
PRE WASH
Warm pre-wash before the main wash that follows automatically; with
intermediate spin for COTTONS/LINEN and EASY-CARES, without intermediate spin for DELICATES.
STAIN
For heavily soiled or stained washing. Stain removal agent will be rinsed
into the wash at the optimum point in the programme.
Can only be set for wash temperatures of 40°C and upwards as stain removers only become effective at higher temperatures.
Starting a programme
1. Check that the tap is turned on.
2. Press the START/PAUSE button. The programme is started.
3 If after pressing the START/PAUSE button E40 flashes in the multi-dis-
play, the END indicator flashes 4 times and at the same time an acoustic signal sounds 4 times, the door has not been correctly shut. Push the
door firmly closed and press the START/PAUSE button again.
Programme sequence
• The programme progress display shows the programme step that is
currently being carried out.
• The multi-display shows the estimated time remaining (in minutes)
until the end of the programme.
3 The time remaining can increase or stay the same for a while during the
course of the cycle as the programme adjusts itself to various conditions (e.g. type of washing and quantity, out of balance spin detection,
special rinse cycle, etc.).
Interrupting a programme/adding washing
Interrupting a programme
• A programme can at any time be interrupted by pressing the START/
PAUSE button and resumed by pressing START/PAUSE again.
• To cancel a programme before it has ended, turn the programme selector to OFF. Important: Be careful of water in the appliance.
14
Adding washing
Washing can be added, as long as the DOOR indicator is illuminated
green.
1. Press the START/PAUSE button. The door can be opened.
2. Close the door and press the START/PAUSE button again. The pro-
gramme will continue.
End of the wash cycle/removing the washing
At the end of the programme, END lights up on the programme
progress display. The door can be opened as soon as the DOOR indicator
is lit green.
1. Open the loading door and remove the washing.
2. Turn the programme knob to OFF.
3. Close the water valve.
4. After washing, pull out the detergent drawer a little to enable it to dry
out. Keep the loading door very slightly open so that the washing machine can air.
If RINSE HOLD has been selected:
After the rinse hold, END lights up on the programme progress display.
The water must first be drained:
– Either turn the programme knob to OFF, then to DRAIN and press the
START/ PAUSE button (the water is drained without spinning),
– or turn the programme knob to OFF and then to SPIN. Change the
spin speed if necessary and press the START/PAUSE button (the water
is drained and the washing spun).
15
Child safety device
If the child safety device has been activated, the door can no longer be
shut.
Activating the child safety device:
Use a coin to turn the knob (on the
inside of the door) in a clockwise direction as far as it will go.
1 Warning! The knob must not be de-
pressed after being set, otherwise
the child safety device is not activated. The knob must stand proud
as shown in the illustration.
16
Deactivating the child safety device:
Turn the knob in an anti-clockwise direction as far as it will go.
Cleaning and care
Important: Do not use furniture cleaning products or aggressive clean-
ing agents to clean the appliance.
Wipe over the control panel and housing with a damp cloth.
Detergent drawer
The detergent drawer should be cleaned regularly.
1. Remove the detergent drawer by pulling firmly.
2. Remove the softener insert from the
middle compartment.
3. Clean all parts with water.
4. Place the softener insert in as far as
it will go, so that it is firmly in position.
5. Clean the entire drawer recess area
of the washing machine, in particular the jets on the upper side of the
washing-in chamber, with a brush.
6. Place the detergent drawer in its
guide rails and push it in.
Washing drum
Rust deposits in the drum may occur due to rusting foreign bodies in
the washing or tap water containing iron.
Important! Do not clean the drum with acidic descaling agents, scouring agents containing chlorine or iron or steel wool.
1. Remove any rust which has accumulated in the drum using a cleaning
agent for stainless steel.
2. Run a washing cycle without any washing to clean off any cleaning
agent residues. Programme: COTTONS/LINEN 60, press the TIME SAVER
button, add approx. 1/4 measuring cup of detergent.
Door and rubber collar
Regularly check whether deposits or foreign substances are present in
the folds of the rubber collar or inside on the door glass.
Regularly clean the door glass and the rubber collar.
17
What to do if...
Remedying small faults yourself
If during use of the appliance one of the following error codes is shown
in the multi-display:
– E10 (Problems with the water inflow),
– E20 (Problems with the water outflow),
– E40 (door open),
please consult the following table.
After the error has been remedied, press the START/PAUSE button.
In the event of other errors (E and a number or letter): Switch the appliance off and then on again. Set the programme again. Press the
START/PAUSE button.
If the error appears again, please contact your local Service Force Centre, stating the error code.
Problem Possible cause Remedy
Washing machine does
not work.
The door cannot be
closed.
When you press a button Err appears in the
multi-display.
E40 appears.
The END indicator is
flashing 4 times, and simultaneously an acoustic signal is sounding 4
times.
Power plug not plugged in
or problem with the fuse.
The door is not shut properly.
The START/ PAUSE button
was not pressed for long
enough.
The child safety device is activated.
The selected function cannot be used together with
the wash programme set.
The door is not closed properly.
Connect the plug to a mains
socket. Check the fuse.
Close the door until the lock
audibly clicks into place.
Press the START/PAUSE button for a longer period of
time.
Deactivate the child safety
device:
Select another function.
Close the door properly. Restart the programme.
18
Problem Possible cause Remedy
E10 appears.
The END indicator is
flashing once, and simultaneously an acoustic signal is sounding
once.
(Problems with the water inflow.)
The washing machine
vibrates when operating
or is not stable.
Water is running out
from under the washing
machine.
The wash water is
foaming a lot. At the
end of the wash cycle
the spinning stops.
E20 appears.
The END indicator is
flashing twice, and simultaneously an acoustic signal is sounding
twice.
(Problems with the water outflow.)
The tap is shut off. Turn on the tap.
The filter in the inlet hose
screw connection is blocked.
The tap is blocked by limescale or faulty.
The transit packaging has
not been removed.
The screw feet have not
been correctly adjusted.
There is very little washing
in the drum (e.g. just one
bathrobe).
The inlet hose screw connection is leaking.
The outlet hose is leaking. Replace outlet hose.
The drain pump lid has not
been closed properly.
Washing was caught in the
door.
The emergency drain hose is
leaking.
Probably too much detergent has been used.
There is a kink in the outlet
hose.
The maximum pump height
of 1m has been exceeded.
The drain pipe is blocked.
For sink spigot connections:
The spigot is blocked.
Turn off the tap. Unscrew the
hose, remove the filter and
clean it.
Check the tap and have it repaired, if necessary.
Remove the transit packaging.
Adjust the feet as described
in the installation and connection instructions.
Operation is not affected by
this.
Tighten the inlet hose.
Close the cover properly.
Load carefully next time you
wash.
Screw on the emergency
drain hose firmly.
Follow the manufacturer's
instructions exactly when
measuring out detergent.
Straighten the hose.
Please contact your local
Service Force Centre
Switch off the appliance.
Disconnect the power plug.
Clean the drain pump. Remove foreign bodies from
the pump housing.
Clean the spigot.
19
Problem Possible cause Remedy
Conditioner has not
been rinsed in, compartment w for conditioner is filled with
water.
The door cannot be
opened when the washing machine is switched
on.
The washing is badly
creased.
The softener insert in the
compartment for conditioners has not been correctly
inserted or is blocked.
The door is locked.
There has been a power cut.
(All the indicators have gone
out.)
The door remains locked for
approx. 4 to 10 minutes.
Perhaps too many items
were loaded.
Clean the detergent drawer,
insert the conditioner insert
firmly.
Wait until the DOOR indicator is illuminated green.
The programme will continue
when the power cut has ended.
To remove the washing:
If water can be seen in the
appliance, prior to opening
the door first let the water
out (see section “Carrying
out an emergency drain”).
Observe the maximum load
volume.
If the wash result is not satisfactory
The washing is grey and there are limescale deposits in the drum
• Too little detergent was used.
• An incorrect detergent was used.
• Individual stains were not pre-treated.
• The programme or temperature was not set properly.
20
There are grey stains on the washing
• Items that were soiled with ointments, fats or oils were washed using
too little detergent.
• The wash temperature used was too low.
• A common cause is that conditioner – in particular the type in con-
centrated form - has come in contact with the washing. Wash out
such marks as soon as possible and exercise care when using the said
conditioner.
Foam can still be seen following the final rinse
• Modern detergents can cause foam to be created even during the fi-
nal rinse. In spite of this, the washing has been sufficiently rinsed.
There are white residues on the washing
• What can be seen here are insoluble substances which modern deter-
gents contain. They are not the result of insufficient rinsing.
Shake or brush the washing. If possible turn the washing inside out
before washing. Check your selection of detergent and perhaps use
liquid detergent instead.
Carrying out an emergency drain
1 Warning! Prior to carrying out an emergency drain, switch off the
washing machine and remove the power plug from the power point.
Warning! The water that comes out of the emergency drain hose may
be hot. There is a risk of scalding. Let the water cool before performing
an emergency drain!
1. Open the plinth flap and remove it.
2. Remove the emergency drain hose.
3. Place a shallow container under-
neath it. Then loosen the drain plug
by turning it in an anti-clockwise
direction and pull it out.
4. The water will run out. If it is necessary to empty the container more
than once, seal up the emergency
drain hose with the drain plug while
you are doing so.
When the water has all drained away:
5. Insert the plug firmly into the emergency drain hose and turn it in a
clockwise direction until it is firmly in place.
6. Replace the emergency drain hose into the retainer.
7. Insert the plinth flap into place and close it.
21
Drain pump
The drain pump is maintenance-free. It is only necessary to open the
pump cover if there is a malfunction and water is no longer being
pumped out, e.g. if the pump wheel is blocked.
Before loading the machine, please always ensure that there are no foreign bodies present in the pockets or in between the items to be
washed. Paper clips, nails, etc. which may find their way into the washing machine along with the washing will remain in the drain pump
housing (foreign body trap that protects the pump wheel).
1 Warning! Before opening the cover of the drain pump, switch off the
washing machine and remove the power plug from the power point.
1. First carry out an emergency drain.
2. Place a cloth on the floor in front of the cover of the drain pump.
Residual water runs out.
3. Unscrew the pump cover in an anticlockwise direction and remove it.
4. Remove foreign bodies and fluff
from the pump housing and from
the pump wheel.
5. Check whether the pump wheel
right at the back of the pump housing can turn. (If the wheel rotates
with a jerky motion, this is normal.)
If the pumping wheel cannot be
turned, please contact your local
Service Force Centre..
6. Insert the pump cover. Insert the
guides at the sides of the cover into
the guide slots and tighten the cover by turning in a clockwise direction.
7. Close off the emergency drain hose
and place it in the retainer.
8. Close the plinth flap.
22
Technical data
This appliance conforms with the following EU Directives:
5
– 73/23/EEC dated 19.02.1973 Low Voltage Directive
– 89/336/EEC dated 03.05.1989 EMC Directive inclusive of Amending
Directive 92/31/EEC
– 93/68/EEC dated 22.07.1993 CE Marking Directive
Height x width x depth 850 x 598 x 640mm
Depth when door is open 1,017 mm
Height adjustability approx. +10/-5mm
Load (depending on programme) max. 6kg
Area of use Household
Drum spin speed see Rating Plate
Water pressure 1-10bar (=10–100N/cm2=0,1–1,0MPa)
Consumption values
The consumption values were obtained under standardised conditions.
They can differ in household use.
Programme selector
(Temperature)
ENERGY SAVING
COTTONS/LINEN 95 6 62 2,20
COTTONS/LINEN 40 6 58 0,70
EASY-CARES 40 3 58 0,52
DELICATES 30 3 58 0,42
WOOL H (Hand-washing) 30 2 54 0,35
1) The load size is determined in accordance with the EN 60456 standard loads.
2) Note: Programme settings for tests in accordance with or in support of EN 60 456
and IEC 60 456.
Consumption values will vary from those quoted depending on the pressure and
hardness of the water and its initial temperature, the room temperature, type and
quantity of washing, detergent used, fluctuations in mains voltage and options selected.
2)
Load size
1)
in kg
6 49 1,02
Water
in litres
Energy
in kWh
23
Installation and connection instructions
1 Safety information concerning
installation
• This washing machine cannot be built-in.
• Before using for the first time, check the appliance for damage sus-
tained while it was being transported. Do not under any circumstances connect an appliance that is damaged to the mains. In the event of
damage to the appliance contact your supplier.
• Be sure to remove all the components of the transit packaging before
using the appliance for the first time. Otherwise when spinning damage may be caused to the appliance or to neighbouring units or furniture.
• Before using the appliance for the first time, splash protection must
be completed. (See “Removing transit packaging”).
• Always plug the mains plug into a correctly installed shockproof
socket.
• If hard-wired: hard-wiring to the mains may only be carried out by
an a qualified electrician.
• Prior to using the appliance for the first time, ensure that the rated
voltage and current on the rating plate match the mains voltage and
current where the appliance is to be installed. The required fuse protection is also to be found on the rating plate.
• If work on the plumbing is required for the proper connection of the
washing machine to the water supply, this must be undertaken by a
registered plumber.
• If work on the electricity supply system is required for the proper
connection of the washing machine to the electricity supply, this
must be undertaken by a registered electrician.
• The washing machine’s mains cable must only be replaced by a
Service Force Engineer
24
Installing the appliance
Transporting the appliance
1 Warning: The washing machine is very heavy. There is a risk of injury.
Exercise care when lifting the appliance.
• Do not lay the washing machine on its front nor on its right side
(as seen from the front). Electrical components may get wet.
• Never transport the appliance without using the transit packaging.
Only remove the transit packaging when the appliance is in its place
of installation. Transporting the appliance without the use of the
transit packaging can cause damage to the appliance.
• Never lift the appliance by the door when it is open nor by the plinth.
When using a sack trolley to transport the washing machine:
• Only use the sack trolley on the side of the appliance.
Removing the transit packaging
Important! Be sure to remove all
the components of the transit packaging prior to using the appliance
for the first time. Keep the transit
packaging in a safe place, in case it
is needed at a later date when the
appliance is to be moved
(e.g. moving house).
1. Open the two hose retainers located
at the rear of the appliance and remove the hoses and electrical cable.
2. Remove the two hose retainers from
the appliance with a strong tug.
25
3 Special spanner A and sealing caps B
(2 units) and C (1 unit) come with
the appliance.
3. Use special spanner A to remove
screw D and the compression spring.
4. Use sealing cap C to cap the hole.
5. Use special spanner A to remove the
two screws E.
6. Use special spanner A to remove the
four screws F.
7. Remove transit bar G.
8. Screw in the four screws F again.
9. Use sealing caps B to cap the two
large holes.
Important: Press all sealing caps B
(2 items) and C (1 item) in firmly so
that they snap into the rear wall.
Where to install
Important! The washing machine must not be operated in a room
where there is a danger of frost. There is a risk of frost damage or adverse effect on the perfomance of the machine. Frost damage is not
covered under the warranty.
• The surface on which the appliance is to be installed must be firm
and level. Do not install the appliance on carpeted floors or soft floor
coverings.
• The surface on which the appliance is to be installed must be clean
and dry and free from grease, so that the appliance does not slide.
• If the location in which the appliance is to be installed is fitted with
small-format tiles, put a rubber mat (available in the shops) under
the appliance.
26
If the appliance is to stand on a floor which moves, e.g. a suspended wooden floor:
Place the appliance in an area as close as possible to a corner of the
room.
Screw a water-resistant wooden board (at least 15 mm thick) onto at
least 2 of the floor joists.
Making the appliance level
The four feet of the appliance are
pre-adjusted.
Large degrees of unevenness can be
compensated for by adjusting the
four feet of the appliance.
Use the special spanner supplied to
do this.
Important: Do not use pieces of
wood, cardboard or such like to level
out small degrees of unevenness in
the floor. Adjust the adjustable feet
instead.
Electrical Connection
Any electrical work required to install this appliance should be carried
out by a qualified electrician or competent person.
1 WARNING – THIS APPLIANCE MUST BE EARTHED.
The manufacturer declines any liability should these safety measures
not be observed.
Before switching on, make sure the electricity supply voltage is the
same as that indicated on the appliance rating plate.
The appliance is supplied with a 13 amp plug fitted. In the event of
having to change the fuse in the plug supplied, a 13 amp ASTA approved (BS 1362) fuse must be used.
Should the plug need to be replaced
for any reason, proceed as described
below.
The wires in the mains lead are
coloured in accordance with the
following code:
27
Green and Yellow: Earth
Blue: Neutral
Brown: Live
• The wire coloured green and yellow
must be connected to the terminal
marked with the letter “E“ or by the
earth symbol E or coloured green and yellow.
• The wire coloured blue must be connected to the terminal “N“ or
coloured black.
• The wire coloured brown must be connected to the terminal marked
“L“ or coloured red.
• Upon completion there must be no cut, or stray strands of wire
present and the cord clamp must be secure over the outer sheath.
1 WARNING! A cut off plug inserted into a 13 amp socket is a serious
safety (shock) hazard. Ensure that the cut off plug is disposed of safely.
Permanent Connection
In the case of a permanent connection it is necessary that you install a
double pole switch between the appliance and the electricity supply
(mains), with a minimum gap of 3mm between the switch contacts and
of a type suitable for the required load in compliance with the current
electrical regulations.
The switch must not break the yellow and green earth cable at any
point.
This appliance complies with the requirements laid out in the EEC Directive 76/899.
Voltage 240 V AC: Fuse rating 13amps
See rating plate for further information.
This appliance meets VDE requirements.
Particular regulations of local electricity authorities must be observed.
This appliance conforms to EEC Directive No. 82/499/EWG on radio interference.
1 WARNING! Repairs to electrical appliances must only be carried out by
trained personnel. Improper repairs may lead to serious risks for the user.
28
Connecting the appliance to the water
supply
Important:
• This appliance must not be connected to the hot water supply.
• When connecting the appliance, use only new hose kits.
• Only connect the appliance to the drinking water supply. Rain water
or water for industrial use may only be used if it fulfils the requirements of DIN1986 and DIN1988.
• Do not kink or crush the water inlet hose or drain hose.
Permitted water pressure
The water pressure must be at least 1 bar (= 10N/cm2=0.1MPa), and
may be a maximum of 10bar (=100N/cm
– If more than 10bar: Connect a pressure reduction valve.
– If less than 1bar: Disconnect the appliance end of the inlet hose from
the solenoid inlet valve and remove the flow meter. (In addition remove the filter using pointed pliers and take out the rubber gasket
behind it.) Replace the filter.
2
=1MPa).
29
Water inlet
A 1.35m long pressure hose is supplied with the appliance.
If a longer inlet hose is required, only hoses from the manufacturer are
to be used. Your local Service Force stocks hose kits of different lengths.
3 Sealing rings are either inserted in the plastic nuts of the threaded hose
fitting or are included as spare parts. Do not use any other sealing
rings.
Important! All threaded hose fittings must only be tightened by
hand.
1. Connect the hose with the right-angle connector to the machine.
Important! Do not position the inlet
hose vertically downwards. Position
it to the right or the left as shown in
the illustration.
2. Connect the hose with the straight
connector to a water tap with an R
¾ (inch) screw thread.
3. Slowly turn on the tap and check
that all connections are watertight.
30
Water Drainage
The appliance drain hose should hook into a standpipe, the hook in the
drain hose is formed using the plastic “U-Piece“ supplied. The standpipe
should have an internal diameter of approximately 38 mm (see diagram) thus ensuring there is an air break between the drain hose and
standpipe.
Important! It is essential to lay the drainage hose without kinks.
When discharging into a stand-
pipe ensure that the top of the
curve in the hose end is no more
than 90 cm (35.4’’) and no less
than 60 cm (23.6’’) above floor
level.
The upright standpipe should
have a minimum, length of 30 cm
(12’’) from the bottom of the elbow to the top of the pipe (see
diagram). Make sure that it is designed in such a way that the end
of the drain hose cannot be covered with water.
Longer drain hoses are available
in lengths of 2.7 and 4 metres
from your Service Force Centre.
For drainage into an outlet
spigot: If the outlet spigot has not
been used before, remove any blanking plug that may be in place. Push
the drain hose onto the spigot and
secure with a clip if required. Ensure
the drain hose is looped upwards to
prevent waste water from the sink
entering the washing machine.
Important! The end of the drainage hose must not be submerged in the
pumped-out water. Otherwise, the water could be sucked back into the
appliance.
31
Pumping heights of over 1 metre
The washing machine’s drain pump is able to pump water to a height of
1metre, calculated from the surface on which the appliance is installed.
Important! If pumping height is over 1 metre malfunctions and damage to the appliance may arise.
For pumping heights over 1metre a conversion kit can be obtained.
Please contact Service Force Centre.
32
Warranty conditions
Great Britain
Standard guarantee conditions
We, AEG, undertake that if within 12 months of the date of the purchase this AEG appliance or
any part thereof is proved to be defective by reason only of faulty workmanship or materials, we
will, at our discretion repair or replace the same FREE OF CHARGE for labour, materials or carriage
on condition that:
• The appliance has been correctly installed and used only on the electricity or gas supply stated
on the rating plate.
• The appliance has been used for normal domestic purposes only, and in accordance with the
manufacturer's operating and maintenance instructions.
• The appliance has not been serviced, maintained, repaired, taken apart or tampered with by any
person not authorised by us.
• All service work under this guarantee must be undertaken by a Service Force Centre. Any appli-
ance or defective part replaced shall become the Company's property.
• This guarantee is in addition to your statutory and other legal rights.
• Home visits are made between 8.30am and 5.30pm Monday to Friday. Visits may be available
outside these hours in which case a premium will be charged.
Exclusions
This guarantee does not cover:
• Damage or calls resulting from transportation, improper use or neglect, the replacement of any
light bulbs or removable parts of glass or plastic.
• Costs incurred for calls to put right an appliance which is improperly installed or calls to appli-
ances outside the United Kingdom.
• Appliances found to be in use within a commercial environment, plus those which are subject
to rental agreements.
• Products of AEG manufacture which are not marketed by AEG.
European Guarantee
If you should move to another country within Europe then your guarantee moves with you to
your new home subject to the following qualifications:
• The guarantee starts from the date you first purchased your product.
• The guarantee is for the same period and to the same extent for labour and parts as exists in
the new country of use for this brand or range of products.
• This guarantee relates to you and cannot be transferred to another user.
• Your new home is within the European Community (EC) or European Free Trade Area.
• The product is installed and used in accordance with our instructions and is only used domesti-
cally, i.e. a normal household.
• The product is installed taking into account regulations in your new country.
Before you move please contact your nearest Customer Care centre, listed below, to give them details of your new home. They will then ensure that the local Service Organisation is aware of your
move and able to look after you and your appliances.
France Senlis +33 (0) 3 44 62 29 29
Germany Nürnberg +49 (0) 800 234 7378
Italy Pordenone +39 (0) 800 117511
Sweden Stockholm +46 (0) 8 672 5360
UK Slough +44 (0) 1753 219899
33
34
Service and Spare Parts
If the event of your appliance requiring service, or if you wish to purchase spare parts, please contact Service Force by telephoning:
0870 5 929 929
Your telephone call will be automatically routed to the Service Force
Centre covering your post code area.
For the address of your local Service Force Centre and further information about Service Force, please visit the website at
www. serviceforce.co.uk
Before calling out an engineer, please ensure you have read the details
under the heading „What to do if...“
When you contact the Service Force Centre you will need to give the
following details:
1. Your name, address and post code.
2. Your telephone number.
3. Clear and concise details of the fault.
4. The model and serial number of the appliance (found on the rating
plate)
5. The purchase date.
Please note that a valid purchase re-
ceipt or guarantee documentation is
required for in-guarantee service
calls.
Customer Care
For general enquiries concerning
your AEG appliance, or for further
information on AEG products please
contact our Customer Care Department by letter or telephone at the
address below or visit our website at www.aeg.co.uk.
Customer Care Department
AEG Domestic Appliances
55-77 High Street
Slough
Berkshire, SL1 1DZ
Tel: 08705 350350 (*)
For Customer Service in the Republic
of Ireland please contact us at the ad-
dress below:
AEG/ Electrolux Group (Ire) Ltd
Long Mile Road/ Dublin 12
Republic of Ireland
Tel: +353 (0) 1 4090751
Email: service.eid@electrolux.ie
(*) Calls may be recorded for training purposes
35
From the Electrolux Group. The world´s No.1 choice.
The Electrolux Group is the world´s largest producer of powered appliances for kitchen, cleaning and outdoor
use. More than 55 million Electrolux Group products (such as refrigerators, cookers, washing machines,
vacuum cleaners, chain saws and lawn mowers) are sold each year to a value of approx. USD 14 billion in more
than 150 countries around the world.
AEG Hausgeräte GmbH
Postfach 1036
D-90327 Nürnberg
http://www.aeg.hausgeraete.de
© Copyright by AEG
105 176 195-00-140504-01
Subject to change without notice
documentation manual, user maintenance, brochure, user reference, pdf manual
This file has been downloaded from:
User Manual and User Guide for many equipments like mobile phones, photo cameras, monther board, monitors, software, tv, dvd, and othes..
Manual users, user manuals, user guide manual, owners manual, instruction manual, manual owner, manual owner's, manual guide,
manual operation, operating manual, user's manual, operating instructions, manual operators, manual operator, manual product,
Loading...