AEG L12720VIT Schematic

 ELECTROLUX HOME PRODUCTS

ITALY S.p.A.
Spares Operations Italy
Corso Lino Zanussi, 30

I - 33080 PORCIA /PN

Fax [phone]

Edition: 2005-01-12 dmm

Publication no.

599 36 82-59

EN

SERVICE MANUAL

WASHING

WASHING-MACHINES

WASHER-DRYERS

with electronic control

EWM2000EVO

Production ZP (Porcia-Italy)

&

with sensors

“FULL SMD”

display board

SOI/DT 2005-01 dmm 2/67 599 36 82 59

INDICE

1

Purpose of this manual .............................................................................................................................. 6

2 PRECAUTIONS ......................................................................................................................................... 6

3 GENERAL SPECIFICATIONS................................................................................................................... 7

3.1 General specifications WM ................................................................................................................. 7

3.2 General specifications WD .................................................................................................................7

4 CONTROL PANEL..................................................................................................................................... 8

4.1 Control/display board.......................................................................................................................... 9

4.1.1 Version with display..................................................................................................................... 9

4.1.2 Version without display................................................................................................................ 9

5 WASHING PROGRAMMES ....................................................................................................................10

5.1 Configuration of programmes ........................................................................................................... 10

5.2 Programme selector ........................................................................................................................10

5.3 Start/Pause ....................................................................................................................................... 10

5.4 Button functions ................................................................................................................................ 10

6 WASHING PROGRAMMES AND OPTIONS ..........................................................................................11

6.1 Possible programmes ....................................................................................................................... 11

6.2 Options of the washing cycle ............................................................................................................ 12

6.3 Description of options ....................................................................................................................... 13

6.3.1 Night cycle ................................................................................................................................. 13

6.3.2 Rinse Hold ................................................................................................................................. 13

6.3.3 Prewash..................................................................................................................................... 13

6.3.4 Soak........................................................................................................................................... 13

6.3.5 Stains......................................................................................................................................... 13

6.3.6 Short (daily) ............................................................................................................................... 13

6.3.7 Very Short.................................................................................................................................. 13

6.3.8 Intensive .................................................................................................................................... 13

6.3.9 Economy / Energy label............................................................................................................. 14

6.3.10 Sensitive .................................................................................................................................... 14

6.3.11 Extra rinse .................................................................................................................................14

6.3.12 Bleach........................................................................................................................................ 14

6.3.13 “Half load” button ....................................................................................................................... 14

6.3.14 Easy-Iron ................................................................................................................................... 14

6.3.15 Reduced spin speed.................................................................................................................. 14

6.3.16 No spin....................................................................................................................................... 14

6.3.17 Modifying the spin speed........................................................................................................... 15

6.3.18 Time reduction (Quick) .............................................................................................................. 15

6.3.19 Temperature adjustment ...........................................................................................................15

6.3.20 Delayed-start time .....................................................................................................................15

6.3.21 Exclude buzzer .......................................................................................................................... 15

6.3.22 Electronic drying (WASHER-DRYERS – certain models only) ................................................. 15

6.3.23 “Drying time” button ...................................................................................................................15

6.3.24 Variation of rinses when options are selected........................................................................... 16

6.4 Display (certain models only)............................................................................................................ 16

6.5 LEDs ................................................................................................................................................. 17

7 WASHING PROGRAMMES ....................................................................................................................18

7.1 Base programmes for Cotton / Linen: cold-30-40-60-90° (without options)..................................... 18

7.2 Rinses of Cotton programmes .......................................................................................................... 19

7.3 Cotton / Linen programmes: 90 Eco, 40-60 “energy label” (without options)................................... 20

7.4 Rinses of Cotton / Linen programmes: 90 Eco, 40-60 “energy label” (without options)................... 21

7.4.1 For programmes with two rinses ............................................................................................... 21

7.4.2 For programmes with three rinses............................................................................................. 21

7.5 Synthetics programmes: cold – 30 – 40 – 50 – 60° (without options) .............................................. 22

7.6 Rinses of synthetics programmes .................................................................................................... 23

7.7 Programmes for delicate fabrics: cold – 30° - 40° (without options) ................................................24

7.8 Wool programmes: cold – 30° - 40°.................................................................................................. 25

7.9 Hand wash programmes: cold – 30° - 40°........................................................................................ 26

8 DRYING PROGRAMMES........................................................................................................................ 27

8.1 Drying programme for cotton ............................................................................................................ 27

8.2 Drying programme for synthetics...................................................................................................... 27

8.3 Drum movements at low speed and during spin .............................................................................. 28

8.3.1 D55 Delicate movement ............................................................................................................ 28

8.3.2 N55 Normal movement.............................................................................................................. 28

8.3.3 E55 Vigorous movement ...........................................................................................................28

SOI/DT 2005-01 dmm 3/67 599 36 82 59

8.3.4

PWL_1 (wool) Delicate movement ............................................................................................ 28

8.3.5 PWL_4 (hand wash) Delicate movement .................................................................................. 28

8.3.6 Cotton/Linen, Synthetics – Intermediate Synthetics Prewash Spin ..........................................29

8.3.7 Cotton/Linen, Intermediate Cotton/Linen Wash Spin ................................................................ 29

8.3.8 Cotton/Linen Final Spin ............................................................................................................. 29

8.3.9 Synthetics Final Spin ................................................................................................................. 29

8.3.10 Delicates Final Spin................................................................................................................... 30

8.3.11 Hand Wash and Wool Final Spin .............................................................................................. 30

8.3.12 Easy iron Impulse Cycle EI........................................................................................................ 30

8.3.13 Intermediate Spin for Cotton/Linen Super-rinse option ............................................................. 30

8.3.14 Movement during drying phase ................................................................................................. 30

8.4 Control of water level in tub .............................................................................................................. 31

9 TECHNICAL CHARACTERISTICS..........................................................................................................32

9.1 EWM2000EVO Electronic control.................................................................................................... 32

9.1.1 Functions of the circuit board ....................................................................................................32

9.1.2 Memory in the control system ................................................................................................... 32

9.2 Analogic pressure switch (electronic) ............................................................................................... 34

9.3 Pressure switch ................................................................................................................................35

9.3.1 Pressure switch settings............................................................................................................ 35

9.4 Anti-flooding device ..........................................................................................................................36

9.5 Power supply and programme selection ..........................................................................................36

9.6 Door interlock.................................................................................................................................... 37

9.6.1 Voltmetric interlock with PTC..................................................................................................... 37

9.6.2 Instantaneous door interlock .....................................................................................................38

9.7 Detergent dispenser .........................................................................................................................39

9.8 Water fill system ...............................................................................................................................39

9.9 Flow meter ........................................................................................................................................ 40

9.9.1 Operating principle of flow meter...............................................................................................40

9.10 Drain pump.................................................................................................................................... 41

9.11 Drain pump.................................................................................................................................... 42

9.12 Aqua Control ................................................................................................................................. 42

9.13 Heating system ............................................................................................................................. 43

9.13.1 Heating element ........................................................................................................................43

9.13.2 Temperature sensor .................................................................................................................. 43

9.14 Turbidity sensor............................................................................................................................. 44

9.15 Motor ............................................................................................................................................. 45

9.16 Power supply to motor ..................................................................................................................45

9.17 Anti-foam control system............................................................................................................... 45

9.18 “FUCS” (Fast Unbalance Control System).................................................................................... 46

10 DRYING CIRCUIT................................................................................................................................ 48

10.1 Temperature control...................................................................................................................... 49

Calculating the drying time:...................................................................................................................... 49

11 DEMO Mode......................................................................................................................................... 50

11.1 Exiting demo mode .......................................................................................................................50

12 DIAGNOSTICS SYSTEM..................................................................................................................... 51

12.1 Access to diagnostics system ....................................................................................................... 51

12.2 Exiting diagnostics system ............................................................................................................ 51

12.3 Phases of the diagnostics test ...................................................................................................... 51

12.3.1 Display board diagnostics.......................................................................................................... 53

12.3.2 Programme selector .................................................................................................................. 54

13 ALARMS............................................................................................................................................... 55

13.1 Displaying the alarms to the user (for appliances with Display) ................................................... 55

13.1.1 Alarms displayed during normal operation ................................................................................ 55

13.2 Reading the alarm codes .............................................................................................................. 56

13.2.1 Displaying the alarm .................................................................................................................. 56

13.2.2 Examples of alarm displays....................................................................................................... 56

13.2.3 Operation of alarms during diagnostics..................................................................................... 57

13.3 Notes about some alarms ............................................................................................................. 57

13.4 Rapid reading of alarm codes ....................................................................................................... 57

13.5 Cancelling the last alarm with LEDs .............................................................................................57

13.6 Table of alarm codes..................................................................................................................... 58

14 Operating time counter......................................................................................................................... 61

14.1.1 Operating time reading.............................................................................................................. 61

14.1.2 Displaying the operating time .................................................................................................... 61

15 ACCESSING COMPONENTS .............................................................................................................62

SOI/DT 2005-01 dmm 4/67 599 36 82 59

15.1

Flow meter..................................................................................................................................... 62

15.2 Aqua Control ................................................................................................................................. 62

15.3 Turbidity sensor............................................................................................................................. 63

15.3.1 Installing the turbidity sensor..................................................................................................... 63

16 BASIC CIRCUIT DIAGRAM WD .......................................................................................................... 64

16.1 Key for circuit diagram WD ...........................................................................................................65

17 BASIC CIRCUIT DIAGRAM WM.......................................................................................................... 66

17.1 Key for circuit diagram WM ........................................................................................................... 67

SOI/DT 2005-01 dmm 5/67 599 36 82 59

1 Purpose of this manual

The purpose of this manual is to provide service engineers who are already familiar with the repair procedures
for traditional washing machines with information regarding appliances fitted with the EWM 2000EVO electronic
control system and produced in Porcia (Italy).
The electronic control system EWM 2000EVO consists of a main electronic board and one control/display
board, “Full SMD” version.
The following are described:

• General characteristics

• Control panel and washing programmes

• Technical characteristics

• Guide to the diagnostics

For detailed information concerning hydraulic circuit, structural characteristics of the appliances and
accessibility, please refer to Service Manual of washing machines and washer-dryers Series P6000/Nexus
(publication no. 599 35 23-17).

2 PRECAUTIONS

 Electrical appliances must be serviced only by qualified Service Engineers.
 Always remove the plug from the power socket before touching internal

components.

SOI/DT 2005-01 dmm 6/67 599 36 82 59

3 GENERAL SPECIFICATIONS

3.1 General specifications WM

Programme selector
Serial port

Power supply

Type of washing
Rinsing system
Motor
Spin speed
Anti-unbalancing system
Water fill

Detergent drawer

Control of water level in the tub

Door safety device

Power of heating element
Temperature control
Audible signalling system

Sensors

 16-24 positions with incorporated main switch
 DAAS-EAP communications protocol up to 38400 baud
 220/240V
 50/60 Hz
 Jet-system
 Jet-system
 Collector, with tachometric generator
 850 ÷ 1600 g/’
 FUCS
 1 solenoid valve with 1 inlet – 2 or 3 outlets
 3 compartments: prewash/stains, wash, conditioners
 4 compartments: prewash/stains, wash, conditioners, bleach
 possibility of three-level pressure switch: 2 anti-boiling and

 electronic/analogic pressure switch
 Traditional (with PTC)
 Instantaneous
 Up to 1950W
 NTC sensor
 Traditional, included on display board
 Water level sensor
 Turbidity sensor

anti-flooding safety levels

3.2 General specifications WD

Programme selector
Serial port

Power supply

Type of washing
Rinsing system
Motor
Spin speed
Anti-unbalancing system
Water fill

Detergent drawer

Control of water level in the tub

Door safety device

Power of heating element

Power of drying heating element

Temperature control
Audible signalling system

Sensors

 16-24 positions with incorporated main switch
 DAAS-EAP communications protocol up to 38400 baud
 220/240V
 50/60 Hz
 Jet-system
 Jet-system
 Collector, with tachometric generator
 850 ÷ 1600 g/’
 FUCS
 1 solenoid valve with 1 inlet – 2 or 3 outlets
 3 compartments: prewash/stains, wash, conditioners
 4 compartments: prewash/stains, wash, conditioners, bleach
 possibility of three-level pressure switch: 2 anti-boiling and

anti-flooding safety levels

 electronic/analogic pressure switch
 Traditional (with PTC)
 Instantaneous
 Up to 1950W
 Up to 1840W (920 + 920)
 Only for built-in models up to 1100W (550+550)
 NTC sensor
 Traditional, included on display board
 Water level sensor
 Turbidity sensor

SOI/DT 2005-01 dmm 7/67 599 36 82 59

4 CONTROL PANEL

The configuration of the control panel depends on the following:

ª Type of control/display board (with or without display)
ª Design of the control panel and position of the programme selector (right or left of the buttons)
ª Number and configuration of the buttons (max. 8)
ª ON/OFF switch: incorporated in the programme selector or with separated button.

Version with left selector and incorporated ON/OFF button

Sigma

Alpha

Ellipse

Built-in

Multipanel

Version with left selector and button ON/OFF switch

Version with right selector and incorporated ON/OFF switch

Version with right selector and incorporated ON/OFF switch

Sigma/ZK

Jewel

SOI/DT 2005-01 dmm 8/67 599 36 82 59

Version with left selector and incorporated ON/OFF button

4.1 Control/display board

4.1.1 Version with display

Ö 3 digits

Ö 28 LEDs

Ö 8 buttons

4.1.2 Version without display

Ö 21 LEDs

Ö 6 buttons

Ö 14 LEDs

Ö 6 buttons

SOI/DT 2005-01 dmm 9/67 599 36 82 59

5 WASHING PROGRAMMES

5.1 Configuration of programmes

The table below lists the parameters that can be used to define the washing programmes.

Type of fabric
Special programmes

Temperature

Spin

Options (Normal / Possible)

Programme phases

5.2 Programme selector

The programme selector determines the type of washing cycle
(e.g. water level, drum movement, number of rinses) and the
washing temperature to be selected for each type of fabric.
The programme selector may be rotated in either direction
(clockwise or counter-clockwise).

The first position is used to cancel the current programme (and, if
the main ON/OFF switch is built into the programme selector, to
switch the appliance off).

Cotton/linen, Synthetic fibres, Delicates, Wool, Hand wash, Mini
Soak, Rinses, Spin, Drain, Conditioner
Normal, Maximum: initial and maximum temperatures that can be
selected for a specific washing programme
Normal, Minimum, Maximum
Bleaches, Economy (Energy Label), Stains, Short, Very short,
Reduced spin, Night cycle, Half-load, Easy-Iron, Rinse Hold,
Extra Rinse, Pre-wash, Soak, Sensitive, Vigorous, No spin, Level
of Drying
Pre-wash, Wash, Rinses, Spin, End of cycle, Drying

5.3 Start/Pause

Start: After selecting the programme and the desired options, press this button to start the cycle.
If the delayed-start option has been selected, the count-down will begin, and will be shown on the

display. The LED stops flashing and remains lit for the entire duration of the programme.

Pause: If the button is pressed again, the current programme is interrupted and the display (or the

corresponding LED) begins to flash. When in pause mode, the door can be opened, but only if the
machine is not performing the heating phase, the water level is not high, and the drum is
stationary.

During the pause, the following modifications can be made to the programme:

- the OPTIONS for the cycle can be modified before the start of the phase in which they are
activated

- the SPIN selection can be modified before the beginning of the final spin.

To re-start the programme, press START/PAUSE again.

5.4 Button functions

The washing programmes and the functions for each button vary according to the model, since
these are determined by the procedure for the configuration of the appliance.

SOI/DT 2005-01 dmm 10/67 599 36 82 59

6 WASHING PROGRAMMES AND OPTIONS

g

p

)

6.1 Possible programmes

The wash programmes can be configured to suit personal needs. The table below lists the standard
programmes.

Programme

90

90E

60

60E

Cotton

Synthetics

Delicate fabrics

Wool

Hand wash

Soak

Rinses

Rinse for delicate fabrics

Fabric softener

Drain

Spin

Delicate spin

Short cycle

The data are indicative
(*) “energy label” programmes
(¹) in the washer-dryers this is a drying phase

(**)

Pro

50

50/40E

40
30

Cold (¹)

60

60/50E

50
40
30

Cold (¹)

40
30

Cold

40
30

Cold

40
30

Cold

ramme Grou

Temperature (°C)

85 3
67 2
60 3

50 (*)(**) 2

50 3

44 (*) 2

42
30
20
60

42 (*)

50
40
30
20
40
30
20
40
35
20
40
35
20

30/20 ---- ----

---- 3 Max. 1600

---- 3 Max. 700

---- 1 Max. 1600

---- ---- ----

---- ---- Max. 1600

---- ---- Max. 700
30 2 Max. 1000

No. of rinses Final spin (RPM)

450/650/850/1000/1200/

1300/1400/1600

3

3 Max. 900

3 450/700

3 Max. 1000

3 Max. 1000

Temperature (°C

COTTON 60 E

SOI/DT 2005-01 dmm 11/67 599 36 82 59

G19/20/22 45÷54

6.2 Options of the washing cycle

p

Ph

i

possible

The selection of the options is to be carried out after switching on the appliance and setting the desired
programme with the selector and before pressing the start/pause button.
When the button is pressed, the corresponding LED lights; by pressing it again the LED switches off.

Possible options according the selected programme

OPZIONI

90°C X X X X X X X X X X X X X X X X X

60°C X X X X X X X X X X X X X X X X X
50°C X X X X X X X X X X X X X X X X X
40°C X X X X X X X X X X X X X X X X X
30°C X X X X X X X X X X X X X X X
Cold X X X X X X X X X X X X X X X
60°C X X X X X X X X X X X X X X
50°C X X X X X X X X X X X X X X
40°C X X X X X X X X X X X X X X
30°C X X X X X X X X X X X X

Cold X X X X X X X X X X X X

30°C X X X X
40°C X X X X X X X X

30°C X X X X X X X X

Cold X X X X X X X X

30°C X X X X X
40°C X X X X

30°C X X X X

Cold X X X X

SYNTHETIC

MINI PROGRAMME

DELICATES

WOOL – HAND-

Compatibility with PROGRAMMES

COTTON

FABRICS

SILK

WASH

SOAK

RINSES

CONDITIONER

DRAIN

SPIN

RINSE HOLD

NIGHT CYCLE

PRE-WASH

SOAK

STAINS

INTENSIVE

DAILY

SHORT
ECONOMY
SENSITIVE

EXTRA RINSE

BLEACH

HALF LOAD

Compatibility with OPTIONS

EASY IRON

REDUCED SPIN SPEED

NO SPIN

n

ases

which

selection is

PRE-SELECTION

PRE-WASH

WASH

RINSES

SPIN

Soak

Rinse-hold

Pre-wash

Night cycle

X X X X X X X X
X X X X X

X
X X X X X X X X X X X X X X
X X X X X X X X X X X X

X X X X X X X X X X X

X
X
X
X X X X
X X X X
X X X X
X X X X
X X X X X X X X
X X X X X X X X X
X X X X X X X
X X X X X X X X X X X
X X X X X X X X X X X

X X X X X X X X X X X X

X X X X X X X X X X X X
X X X X X X X X X X X X X X X
X X X X X X X X X X X X X X
X X X X X X X X X X X X X X

X X X

X X X

X X X X X X X X X X X

Daily

Stains

X X X X X X X X X X X

Short

X X X X X X X X

X X X X X X X X

Sensitive

Economy

X X X X X X X X

X X X X X X X X

Bleach

Extra rinse

X X X X X X X

Half-load

X X X X X X

X X X X X

X X X X

eed
s

Easy iron

No spin

Reduced spin

X X X

Drying

Rinse-hold

X

SOI/DT 2005-01 dmm 12/67 599 36 82 59

6.3 Description of options

6.3.1 Night cycle

ª All the spin phases are eliminated. Three rinses are added to COTTON cycles and one rinse is added

to SYNTHETICS cycles.

ª The appliance is shut down with water in the drum before the final spin.
ª No buzzer (if appliance is configured with a buzzer).
ª To drain the water, select a drain or spin cycle.

6.3.2 Rinse Hold

ª The appliance is shut down with water in the drum before the final spin.
ª To drain the water, select a drain or spin cycle.

6.3.3 Prewash

ª A prewash phase is added at the beginning of the cycle. The water is heated to 30°C (or may be cold, if

selected).

ª In COTTON and SYNTHETICS cycles, a short spin (pulse spin) is performed before the wash phase.
ª This option is not available in WOOL and HAND WASH cycles.

6.3.4 Soak

ª A prewash phase is added (lasting 30’, with the same agitation as in the wool cycle) at the beginning of

the programme. The water is heated to 30°C (or may be cold, if selected).

ª In COTTON and SYNTHETICS cycles, a short spin (pulse spin) is performed before the wash phase.
ª When combined with the delayed start option, a soak time from 30 minutes to 10 hours can be selected.
ª This option is not available in WOOL and HAND WASH cycles.

6.3.5 Stains

ª The motor operates for an extra 5 minutes after the water is heated to 40°C.
ª Water is run through the prewash/stain remover compartment to withdraw the special stain removing

product.

ª This option is not available in DELICATE FABRICS, WOOL and HAND WASH cycles.
ª Agitation during washing changes from vigorous to normal.

6.3.6 Short (daily)

ª The structure of the wash phase in the COTTON - SYNTHETICS programmes is modified to obtain

good performance in a short time (optimized for small loads).

6.3.7 Very Short

ª The structure of the COTTON – SYNTHETICS – DELICATE FABRICS programmes is modified to

obtain very short time wash times (optimized for small, lightly soiled loads).

ª The number of rinses is reduced (one less rinse).
ª The water level in the other two rinses is increased.

6.3.8 Intensive

ª 10 minutes of normal movement are added to the wash phase in the cotton programme.

SOI/DT 2005-01 dmm 13/67 599 36 82 59

6.3.9 Economy / Energy label

ª The COTTON 40°/50°/60°/90° - SYNTHETICS 50°/60° programmes are modified to reduce energy

consumption

ª The wash temperature in the 90°/60°/50° programmes is reduced; the temperature in the 40°

programme is increased by 4°.

ª The duration of the wash phase is increased

6.3.10 Sensitive

ª One rinse is added to the COTTON – SYNTHETICS cycles
ª During cotton cycles, agitation is reduced from vigorous to normal
ª Intermediate spin phases are eliminated except for the final two, whose speed is reduced.

6.3.11 Extra rinse

ª Two rinses are added to COTTON cycles, and one rinse is added to SYNTHETICS – DELICATE cycles.
ª Intermediate spin phases are eliminated except for the final two, which are reduced to 450 rpm.

6.3.12 Bleach

ª Ducts water through the bleach compartment at the beginning of the first rinse in COTTON cycles.
ª Pre-wash possible only where there are three solenoids.
ª In models with two solenoids the bleach is not compatible with the pre-wash option.

6.3.13 “Half load” button

ª Eliminates a rinse in the COTTONS programmes.

6.3.14 Easy-Iron

• In COTTON programmes:

ª Adds three rinses.
ª Eliminates the intermediate spins.
ª Performs an impulse spin phase.
ª Adds an “untangling” phase after the spin cycle.

• In SYNTHETICS cycles:

ª Reduces the heating temperature in 50/60° cycles to 40°C.
ª Increases the washing time.
ª Prolongs the cooling phase at the end of the washing phase.
ª Adds one rinse without spin cycle.
ª Adds an “untangling” phase after the impulse spin cycle.

6.3.15 Reduced spin speed
ª Reduces the speed of all spins as shown in the table

Maximum spin speed (rpm)
Reduction for COTTON (rpm)
Reduction for ALL OTHER CYCLES
(rpm)

600 700 800 900 1000 1100 1200 1300 1400 1500 1600
450 450 450 450 500 550 600 650 700 750 800

450 450 450 450 450 450 450 450 450 450 450

6.3.16 No spin

ª Eliminates all the spin phases.
ª If selected, three rinses are added in the COTTON cycle and one in the SYNTHETICS cycle.

SOI/DT 2005-01 dmm 14/67 599 36 82 59

6.3.17 Modifying the spin speed

ª Reduces the speed of all spin cycles.
ª The last position can be used for NO SPIN, RINSE-HOLD.
ª If the NO-SPIN option is selected, three rinses are added in the COTTON cycle, and one in the

SYNTHETICS cycle.

6.3.18 Time reduction (Quick)

ª Modifies the structure of the COTTON - SYNTHETICS– DELICATES programmes to obtain washing

time very short (optimization for small or lightly-soiled loads).

ª Reduces the no. of rinses (one rinse less).
ª Increases the water level of the other two rinses.
ª Corresponds to the SHORT- VERY SHORT cycles on the basis of the configuration of the appliance.

6.3.19 Temperature adjustment

ª Used to select the washing temperature compatibly with the limit temperature for the cycle.
ª Can be used during the cycle selection phase: the temperature can be modified only if the heating

phase has not started (in pause mode).

6.3.20 Delayed-start time

• Models with digit

ª It is possible to select, during the programme selection phase, a delayed start from 30 minutes up to 23

hours () 30’) 60’) 90’) 2h) 3h...) 23h) 0h).

ª During the delay phase, the time decreases every hour up to 2h, then by 30minutes.
ª To start the cycle immediately, after the delay time began: press the Start/Pause button, cancel the

delay time by pressing the relative button and press Start/Pause again.

• Models with led
ª Insert a pause before the start of the programme, the delay time is indicated by the corresponding

LEDs.

ª To start the cycle immediately, after the delay time began: press the Start/Pause button, cancel the

delay time by pressing the relative button and press Start/Pause again.

6.3.21 Exclude buzzer

ª The buzzer can be deactivated by pressing a combination of two buttons simultaneously for 5 seconds.

This option depends on the configuration; as a result, the buttons may vary according to the model.

ª If the buzzer is deactivated, the appliance will emit no acoustic signal during selection or at the end of

the cycle; however, the alarm signalling system remains operative.

6.3.22 Electronic drying (WASHER-DRYERS – certain models only)

Three different degrees of drying can be selected for COTTON, and one for SYNTHETIC fabrics:

ª Extra-dry (cotton only)
ª Cupboard-dry (cotton and synthetics)
ª Iron dry (cotton only)

The appliance automatically calculates the drying time is selected using “fuzzy logic”.
The drying phase may be performed automatically (i.e. without interrupting the programme) if selected
together with a washing programme, or as a separate programme.

6.3.23 “Drying time” button

This button is used to select the drying time for COTTON and SYNTHETIC cycles. The time increases by 5
minutes each time it is pressed (from 10 to 130 minutes).
The drying function can be selected for automatic execution after a washing cycle, or as a separate
programme.

SOI/DT 2005-01 dmm 15/67 599 36 82 59

6.3.24 Variation of rinses when options are selected

Number of rinses for the options

Normal

Sensitive

Super rinse

Easy-iron

Night cycle

No spin

Easy-iron

Night cycle

No spin

Super rinse

Very short 2 3 4 5 6
Short 3 4 5 6 7

COTTON

Eco 3 4 5 6 7
Eco 2 3 4 5 6
Normal 3 4 5 6 7

Very short 2 3 3 3 5

SYNTHETICS

Short 3 4 4 4 5
Eco 3 4 4 4 5
Normal 3 4 4 4 5

PROGRAMMES

DELICATE

Very short 2 - 3 - ­Normal 3 - 4 - -

Normal 3 - - - -

WOOL Normal 3 - - - -

HAND WASH Normal 2 3 3 3 5

N.B.: The HALF-LOAD option subtracts one rinse from all COTTON programmes, except for the

VERY SHORT programme.

- The turbidity sensor adds one rinse if there is too much foam or the water is very dirty in all programmes,
except COTTON ECO and SYNTHETICS.

6.4 Display (certain models only)

The following information appears on the display:

ª Three flashing dashes appear when the appliance is switched on
ª The duration of the wash programme appears when the programme is selected. This value is the

amount of time necessary for washing the maximum load of laundry for the type of programme selected.
When the programme is started, the time counts down minute by minute.

ª The end of the programme is indicated by a “0” (when the door can be opened)
ª Delayed start is selected using the relative button. When the START/PAUSE button is pressed, the

time begins counting down and decreases an hour at a time until 2 hrs remain, then the decrease is 30
minutes at a time.

Ö An alarm code indicates a malfunction has occurred.

SOI/DT 2005-01 dmm 16/67 599 36 82 59

6.5 LEDs

These LEDs display different information depending on machine configuration; the end-of-cycle LED is
present on all models.

Type of LED Function

Prewash

Wash

Prewash/

Wash

Rinse

Spin

Drain

Extra rinse

Rinse Hold

Cycle in

progress

End of cycle

This LED lights up if the selected programme includes a prewash, and lights up during the
prewash phase when the programme is executed.
This LED lights up if the selected programme includes a wash phase, and lights up during
the wash phase when the programme is executed.
This LED lights up if the selected programme includes a prewash or wash phase, and
lights up during the prewash or wash phase when the programme is executed.
This LED lights up if the selected programme includes rinses, and lights up during the
rinses when the programme is executed.
This LED lights up if the selected programme includes a spin phase, and lights up during
the spin phase when the programme is executed.
This LED lights up if the selected programme includes a drain phase, and lights up during
the drain phase when the programme is executed.
This LED lights up when the programme is chosen if an extra rinse has been
selected/stored (if an extra rinse is included in the programme), and lights up during the
extra rinse when the programme is executed.
This LED lights up when the programme is chosen if this option has been selected, and at
the end of the cycle when the machine stops with water in the drum.

This LED lights up while the programme is being executed.

This LED lights up at the end of the cycle; it is also used to signal alarms.

Filter clogged

Detergent

overload

ON/OFF

Door

Time until end

of cycle

Drying

This LED lights up at the end of the cycle if the drain filter is clogged.

This LED lights up at the end of the cycle if too much detergent has been used.

This LED lights up when the machine is switched on.

ª This LED lights up when the door is locked by the safety system.
ª The LED switches off when the door is no longer locked.
ª The LED flashes while the door is being unlocked (which occurs masterly on models

with a safety system equipped with a PTC)
This LED lights up when the display is showing the time remaining until the end of the
cycle.
Lights during selection if the programme includes a drying cycle and during the cycle when
it is in progress.

SOI/DT 2005-01 dmm 17/67 599 36 82 59

7 WASHING PROGRAMMES

7.1 Base programmes for Cotton / Linen: cold-30-40-60-90° (without options)

N.° Phase Description

1 Calibration Level ON OFF No Movement DRAIN

2 Flow Calibration Level OFF OFF PW No Movement WATER FILL

3 Water softener Maintenance Time OFF OFF PW 55 4 12 1 min.

4 Water fill Level OFF OFF PW No Movement COT_FIRST_PW_LEV

5 Maintenance & Refill Time OFF ON (35/15) PW 55 4 12

Pre-wash

6 Heating Temperature OFF ON (35/15) PW 55 4 12 Heating up to 30° or 20 min. 20° o 20 min.
7 Maintenance Time OFF ON (35/15) PW 55 4 12 4 min.

8 Drain Time ON OFF No Movement Empty Elect. + 14 Sec.
9

10 Calibration Level ON OFF No Movement DRAIN
11 Flow Calibration Level OFF OFF PW No Movement WATER FILL
12 Maintenance & Refill Time OFF OFF PW 55 4 12 1 min.
13 Water fill Level OFF OFF W No Movement COT_FIRST_W_LEV

14 Maintenance & Refill Time OFF ON (35/15) W 55 8 8

15 Heating Temperature or time OFF ON (35/15) W 55 8 8 40° o 40 min. 40° o 80 min.
16 Heating Temperature or time OFF ON (35/15) W 55 8 8 60° o 40 min. 60° o 80 min. 41° o 10 min. 30° o 80 min. 20° o 80 min.
17 Heating Temperature or time OFF OFF W 55 8 8 85° o 40 min.

18 Maintenance heating Temperature or time OFF ON (35/15) W

19 Maintenance Time OFF ON (35/15) W

20 Maintenance Time OFF ON (35/15) W 55 8 8 3 min.
21 Heating Temperature or time OFF OFF W 55 10 3 5 min.

22 Heating Temperature or time OFF ON (35/15) W 55 8 8 60° o 20 min.

23 Heating Temperature or time OFF ON (35/15) W 55 10 3 41° o 10 min. 30° o 20 min.
24 Maintenance Time OFF ON (35/15) W 55 10 3 5 min. 10 min. 10 min. 10 min. 10 min.

25 Maintenance Time OFF OFF W 55 8 8 5 min. 5 min. 5 min.
26 Maintenance Time OFF ON (35/15) W 55 10 3 10 min. 10 min. 10 min.
27 Maintenance Time OFF OFF W 55 8 8 10 min. 15 min. 15 min. 15 min.
28 Maintenance Time OFF OFF W 55 10 3 10 min.
29 Maintenance Time OFF OFF W 55 8 8 4 litres
30 Cooling Time OFF OFF W 55 4 12 2 min.

31

32 Drain Time ON OFF No Movement Empty Elect. + 14 Sec.
33 Spin Time ON OFF IMP_6 5 min. with AS control
34

(The data are indicative)

PW = Pre-wash W = Wash AS = Anti-foam control
Only if cycle begins with a wash phase and not with a prewash

Spin Time ON OFF IMP C0 4,5 min. with AS control

Wash

Calibration of Turbidity
Sensor

Drain Time ON OFF No Movement 20 sec.

Time ON OFF No Movement 20 sec.

Drain
pump

Recirc.

pump

Deterg

Dispens.

Motor Movement CYCLE

Rpm Movem. Pause 90° 60°/60° 40° 30° *

4 min.

COT_FIRST_PW_LEV

5 min.

COT_SEC_NW_LEV

55/10/3

if 90° 55/8/8

55/10/3

if 90° 55/8/8

41° o 5 min.

2 min. 5 min.

T° ref.
5 min.

T° ref.
5 min.

SOI/DT 2004-11 dmm 599 36 75-68

18/67

7.2 Rinses of Cotton programmes

N.° PHASE Description

35 Water fill Level OFF ON (35/15) BL No movement COT_FIRST_N_R_TURB_LEV

36 Maintenance & Refill Time OFF ON (35/15) W 55 8 8
37 Turbidity measurement Time OFF OFF No movement 6 sec.

38 Drain Level ON OFF No movement Empty Elect.+ 14 sec.
39
40 Water fill Level OFF OFF W 55 8 8 Qt
41 Maintenance Time OFF ON(35/15) No movement 20 sec.
42 Wait Time OFF OFF No movement 30 sec
43 Water fill Level OFF ON (35/15) W No movement COT_INT_N_R_LEV

44 Maintenance & Refill Time OFF ON (35/15) W 55 8 8

45 Drain Level ON OFF No movement Empty Elect.+ 14 sec
46
47 Water fill Level OFF OFF SF 55 8 8 DRY_COND_LEV
48 Water fill Level OFF ON SF No movement COT_LAST_N_R_LEV
48 Maintenance Time OFF OFF 55 8 8 30 sec.
50 Water fill Level OFF OFF SF No movement o Qsf (4 Litres)

51 Maintenance & Refill Time OFF ON (35/15) W 55 8 8

52 Drain Level ON OFF No movement Empty Elect.+ 14 sec

53

(The data are indicative)

BL = Bleach SF = Softener W = Wash AS = Anti-foam
Only if Turbidity sensor is featured

Only for Washing machines- Washer-dryers (WD)

1st Rinse

Spin Time ON OFF IMP_C6 5 min. with AS control

2nd Rinse

Spin Time ON OFF IMP_C6 5 min. with AS control

(softener)

Last rinse

Spin ON OFF IMPCF_AC 9 min. with AS control

Drain
pump

Recirc.

Pump

Deterg.

Disp

Motor movement

Rpm Movem. Pause

CYCLE

5 min.

COT_REF_N_R_LEV

5 min.

COT_REF_N_R_LEV

8 min.

COT_REF_N_R_LEV

SOI/DT 2004-11 dmm 599 36 75-68

19/67

7.3 Cotton / Linen programmes: 90 Eco, 40-60 “energy label” (without options)

N.° PHASE Description Drain pump

1 Calibration Level ON OFF No movem DRAIN

2 Flow calibration Level OFF OFF PW No movem WATER FILL

3 Maintenance water softener Time OFF OFF PW 55 4 12 1 min.

4 Water fill Level OFF OFF PW No movem COT_FIRST_PW_LEV

5 Maintenance & Refill Time OFF ON (35/15) PW 55 4 12

Prewash

6 Heating Temperature or time OFF ON (35/15) PW 55 4 12 30° o 20 min.
7 Maintenance

8Drain
9

10 Calibration
11 Flow calibration
12 Maintenance water softener Time OFF OFF PW 55 4 12 1 min.
13 Water fill Level OFF OFF W No movem COT_FIRST_W_LEV

14 Maintenance & Refill
15 Maintenance Time OFF ON (35/15) W 40 10 3 1 min.

16 Maintenance Time OFF OFF W No movem 22 sec.

17 Maintenance & Refill
18 Maintenance Time OFF ON (35/15) W 40 10 3 1 min.

19 Maintenance Time OFF OFF W No movem 22 sec.
20 Heating Temperature or time OFF OFF W 55 8 8 67°÷ 64°o 80 min.54°÷45° o 20 min.44°÷ 40° o 80 min.

22 Maintenance heating Temperature or time OFF ON (35/15) W 55 10 3

23 Maintenance heating Temperature or time OFF OFF W 55 10 3

24
25

26 Heating Temperature or time OFF OFF W

27

28
29 Maintenance Time OFF ON (35/15) W 55 8 8 5 min.

30 Maintenance Time OFF OFF W 55 8 8 5 min. 5 min.
31 Maintenance Time OFF ON (35/15) W 55 10 3 15 min.
32 Drain Time ON OFF No movem Empty Elect. + 14 sec.
33 Spin Time ON OFF IMP_6 5 min. with AS control
34

(The data are indicative)

Spin

Wash

Maintenance
Maintenance

Maintenance

Maintenance

Drain Time ON OFF No movem 20 sec.

Time

Time
Time

Level
Level

Time

Time

Time
Time

Time
Time

Recirc.

Pump

OFF ON (35/15) PW 55 4 12 4 min.

ON OFF No movem Empty Elect. + 14 sec.
ON OFF IMP C0 4,5 min. with AS control

ON OFF

OFF OFF PW

OFF OFF W 40 10 3

OFF OFF W 40 10 3

OFF ON (35/15) W 55 10 3 15 min.
OFF OFF W No movem 30 sec. 30 sec.

OFF ON (35/15) W 55 8 8 10 min.

OFF ON (35/15) W 55 10 3 25 min. 20 min. 20 min.

Deterg.

PW= Prewash W = Wash AS = Anti-foam

The temperature depends on the water Min.45° Max.53°

SOI/DT 2004-11 dmm 599 36 75-68

Only if cycle begins with a wash phase and not with a prewash

20/67

Motor movement CYCLE

Disp

Rpm Movem. Pause 90 60/50 40

4 min.

COT_SEC_PW_LEV

No movem
No movem

55/10/3

40° 55/8/8

T° ref.
5 min.

67°÷ 64°

20 min.

DRAIN

WATER FILL

5 min.

COT_FIRST_W_LEV

1 min.

COT_SEC_EW_LEV

54°÷45°

2 min.

T° ref.

30 min.

44°÷ 40°

20 min.

7.4 Rinses of Cotton / Linen programmes: 90 Eco, 40-60 “energy label” (without options)

7.4.1 For programmes with two rinses

N.° PHASE Description Drain pump

35 Water fill Level OFF ON(35/15) BL No movem COT_FIRST_E_R_LEV

36 Maintenance & Refill Time OFF ON (35/15) W 55 8 8

37 Drain Level ON OFF No movem Empty Elect.+ 14 sec.
38
39 Water fill Level OFF OFF SF 55 8 8 DRY_COND_LEV
40 Water fill Level OFF OFF SF No movem COT_LAST_E_R_LEV
41 Maintenance Time OFF OFF 55 8 8 30 sec.
42 Water fill Level OFF OFF SF 55 8 8 Qsf (4 Litres)

43 Maintenance & Refill

44 Maintenance & Refill

45 Drain

46

Rinse

st

1

Spin ON OFF IMP_6 5 min. with AS control

Time

Time

Time

Spin

Last rinse (softener)

Time

OFF ON (35/15) W

OFF ON (35/15) W 55 8 8

ON OFF No movem Empty Elect.+ 14 sec

ON OFF IMPCF_AC 5 min. with AS control

Recirc.

Pump

Deterg.

Disp

(The data are indicative) BL = Bleach SF = Softener W = Wash AS = Anti-foam control

Only for WD

7.4.2 For programmes with three rinses

N.° PHASE Description Drain pump

35 Water fill Level OFF ON(35/15) BL No movem COT_FIRST_E_R_LEV

36 Maintenance & Refill Time OFF ON (35/15) W 55 8 8

37 Drain Level ON OFF No movem Empty Elect.+ 14 sec.
38
39 Water fill Level OFF OFF W No movem COT_INT_E_R_LEV

40 Maintenance & Refill Time OFF ON (35/15) W 55 8 8

41 Drain Level ON OFF No movem Empty Elect.+ 14 sec.
42
43 Water fill Level OFF OFF SF 55 8 8 DRY_CON_LEV
44 Water fill Level OFF OFF SF No movem COT_LAST_E_R_LEV
45 Maintenance Time OFF OFF 55 8 8 30 sec.
46 Water fill Level OFF OFF SF 55 8 8 Qsf (4 Litres)

47 Maintenance & Refill Time OFF ON (35/15) W

48 Maintenance & Refill Time OFF ON (35/15) W 55 8 8

49 Drain Level ON OFF No movem Empty Elect.+ 14 sec

50

(The data are indicative) BL = Bleach SF = Softener W = Wash AS = Anti-foam control

Only for WD

Rinse

st

1

Spin ON OFF IMP_6 5 min. with AS control

Rinse

nd

2

Spin ON OFF IMP_6 5 min. with AS control

Last rinse (softener)

Spin ON OFF IMPCF_AC 9 min. with AS control

Recirc.

Pump

Deterg.

Disp

Motor Movement

Rpm Movem. Pause

55/8/8 G20

55/4/12 per G22

Motor Movement

Rpm Movem. Pause

55/8/8 per G19 e G20

55/4/12 per G22

CYCLE

8 min.

COT_REF_E_R_LEV

4 min.for G20 and G22

COT_REF_E_R_LEV

4 min.for G20 and G22

COT_REF_E_R_LEV

CYCLE

5 min.

COT_REF_E_R_LEV

5 min.

COT_REF_E_R_LEV

8 min. per G19
4 min. per G20 e G22
COT_REF_E_R_LEV
4 min. per G20 e G22
COT_REF_E_R_LEV

SOI/DT 2004-11 dmm 599 36 75-68

21/67