USER
MANUAL
HG674550
EN User Manual
Hob
www.aeg.com
2
CONTENTS
1. SAFETY INFORMATION.............................................................................................2
2. CONDITIONS OF USE................................................................................................5
3. SAFETY INSTRUCTIONS.............................................................................................5
4. PRODUCT DESCRIPTION...........................................................................................8
5. DAILY USE....................................................................................................................8
6. HINTS AND TIPS........................................................................................................10
7. CARE AND CLEANING.............................................................................................10
8. TROUBLESHOOTING............................................................................................... 12
9. INSTALLATION..........................................................................................................13
10. TECHNICAL DATA..................................................................................................19
11. WARRANTY .............................................................................................................20
FOR PERFECT RESULTS
Thank you for choosing this AEG product. We have created it to give you
impeccable performance for many years, with innovative technologies that help
make life simpler features you might not find on ordinary appliances. Please
spend a few minutes reading to get the very best from it.
Visit our website for:
Get usage advice, brochures, trouble shooter, service information:
www.aeg.com/webselfservice
Register your product for better service:
www.registeraeg.com
CUSTOMER CARE AND SERVICE
Always use original spare parts.
When contacting our Authorised Service Centre, ensure that you have the
following data available: Model, PNC, Serial Number.
The information can be found on the rating plate.
Warning / Caution-Safety information
General information and tips
Environmental information
Subject to change without notice.
SAFETY INFORMATION
1.
Before the installation and use of the appliance,
carefully read the supplied instructions. The
manufacturer is not responsible for any injuries or
damages that are the result of incorrect installation or
usage. Always keep the instructions in a safe and
accessible location for future reference.
ENGLISH
1.1 Children and vulnerable people safety
• This appliance can be used by children aged from 8
years and above and persons with reduced physical,
sensory or mental capabilities or lack of experience
and knowledge if they have been given supervision or
instruction concerning the use of the appliance in a
safe way and understand the hazards involved.
• Do not let children play with the appliance.
• Keep all packaging away from children and dispose of
it appropriately.
• Keep children and pets away from the appliance when
it operates or when it cools down. Accessible parts are
hot.
• If the appliance has a child safety device, this should
be activated.
• Children shall not carry out cleaning and user
maintenance of the appliance without supervision.
• Children aged 3 years and under must be kept away
from this appliance when it is in operation at all times.
3
1.2
General Safety
•
WARNING: The appliance and its accessible parts
become hot during use. Care should be taken to
avoid touching heating elements. Children less than 8
years of age shall be kept away unless continuously
supervised.
• Do not operate the appliance by means of an external
timer or separate remote-control system.
• WARNING: Unattended cooking on a hob with fat or
oil can be dangerous and may result in fire.
• NEVER try to extinguish a fire with water, but switch
off the appliance and then cover flame e.g. with a lid
or a fire blanket.
• CAUTION: The cooking process has to be supervised.
A short term cooking process has to be supervised
continuously.
4
www.aeg.com
• WARNING: Danger of fire: Do not store items on the
cooking surfaces.
• Metallic objects such as knives, forks, spoons and lids
should not be placed on the hob surface since they
can get hot.
• Do not use a steam cleaner to clean the appliance.
• If the glass ceramic surface / glass surface is cracked,
switch off the appliance to avoid the possibility of
electric shock.
• In case of hotplate glass breakage:
– shut immediately off all burners and any electrical
heating element and isolate the appliance from the
power supply,
– do not touch the appliance surface,
– do not use the appliance.
• If the supply cord is damaged, it must be replaced by
the manufacturer, an authorized Service or similarly
qualified persons in order to avoid a hazard.
• Where the appliance is directly connected to the
power supply, an all-pole isolating switch with a
contact gap is required. Complete disconnection in
compliance with the conditions specified in
overvoltage category III must be guaranteed. The
earth cable is excluded from this.
• When you route the mains cable, make sure that the
cable doesn't come into direct contact (for example
using insulating sleeving) with parts that can reach
temperatures of more than 50°C above room
temperature.
• WARNING: Use only hob guards designed by the
manufacturer of the cooking appliance or indicated by
the manufacturer of the appliance in the instructions
for use as suitable or hob guards incorporated in the
appliance. The use of inappropriate guards can cause
accidents.
2. CONDITIONS OF USE
ENGLISH
5
This appliance is suitable for the
following markets: AU NZ
This appliance is intended to be used in
household and similar applications such
as:
3. SAFETY INSTRUCTIONS
3.1 Installation
WARNING!
Only a qualified person must
install this appliance.
WARNING!
Risk of injury or damage to
the appliance.
• Remove all the packaging.
• Do not install or use a damaged
appliance.
• Follow the installation instruction
supplied with the appliance.
• Keep the minimum distance from the
other appliances and units.
• Always take care when moving the
appliance as it is heavy. Always use
safety gloves and enclosed footwear.
• Seal the cut surfaces with a sealant to
prevent moisture to cause swelling.
• Protect the bottom of the appliance
from steam and moisture.
• Do not install the appliance adjacent
to a door or under a window. This
prevents hot cookware to fall from the
appliance when the door or the
window is opened.
• If the appliance is installed above
drawers make sure that the space,
between the bottom of the appliance
and the upper drawer, is sufficient for
air circulation.
• The bottom of the appliance can get
hot. Make sure to install a noncombustible separation panel under
the appliance to prevent access to the
bottom.
• Farm houses
• By clients in serviced apartments,
holiday apartments and other
residential type environments.
3.2 Electrical Connection
WARNING!
Risk of fire and electrical
shock.
• All electrical connections should be
made by a qualified electrician.
• The appliance must be earthed.
• Before carrying out any operation
make sure that the appliance is
disconnected from the power supply.
• Make sure that the parameters on the
rating plate are compatible with the
electrical ratings of the mains power
supply.
• Make sure the appliance is installed
correctly. Loose and incorrect
electricity mains cable or plug (if
applicable) can make the terminal
become too hot.
• Use the correct electricity mains
cable.
• Do not let the electricity mains cable
tangle.
• Make sure that a shock protection is
installed.
• Use the strain relief clamp on the
cable.
• Make sure the mains cable or plug (if
applicable) does not touch the hot
appliance or hot cookware, when you
connect the appliance to the near
sockets
• Do not use multi-plug adapters and
extension cables.
• Make sure not to cause damage to
the mains plug (if applicable) or to the
mains cable. Contact our Authorised
Service Centre or an electrician to
change a damaged mains cable.
• The shock protection of live and
insulated parts must be fastened in
6
www.aeg.com
such a way that it cannot be removed
without tools.
• Connect the mains plug to the mains
socket only at the end of the
installation. Make sure that there is
access to the mains plug after the
installation.
• If the mains socket is loose, do not
connect the mains plug.
• Do not pull the mains cable to
disconnect the appliance. Always pull
the mains plug.
• Use only correct isolation devices: line
protecting cut-outs, fuses (screw type
fuses removed from the holder), earth
leakage trips and contactors.
• The electrical installation must have
an isolation device which lets you
disconnect the appliance from the
mains at all poles. The isolation
device must have a contact opening
width of minimum 3 mm.
3.3 Gas connection
• All gas connections should be made
by a qualified person.
• Before installation, make sure that the
local distribution conditions (nature of
the gas and gas pressure) and the
adjustment of the appliance are
compatible.
• Make sure that there is air circulation
around the appliance.
• The information about the gas supply
is on the rating plate.
• This appliance is not connected to a
device, which evacuates the products
of combustion. Make sure to connect
the appliance according to current
installation regulations. Pay attention
to requirements regarding adequate
ventilation.
3.4 Use
WARNING!
Risk of injury, burns and
electrical shock.
• Remove all the packaging, labelling
and protective film (if applicable)
before first use.
• Use this appliance in a household
environment.
• Do not change the specification of
this appliance.
• Make sure that the ventilation
openings are not blocked.
• Do not let the appliance stay
unattended during operation.
• Set the cooking zone to “off” after
each use.
• Do not put cutlery or saucepan lids on
the cooking zones. They can become
hot.
• Do not operate the appliance with
wet hands or when it has contact with
water.
• Do not use the appliance as a work
surface or as a storage surface.
• When you place food into hot oil, it
may splash.
WARNING!
Risk of fire and explosion
• Fats and oil when heated can release
flammable vapours. Keep flames or
heated objects away from fats and oils
when you cook with them.
• The vapours that very hot oil releases
can cause spontaneous combustion.
• Used oil, that can contain food
remnants, can cause fire at a lower
temperature than oil used for the first
time.
• Do not put flammable products or
items that are wet with flammable
products in, near or on the appliance.
WARNING!
Risk of damage to the
appliance.
• Do not keep hot cookware on the
control panel.
• Do not let cookware to boil dry.
• Be careful not to let objects or
cookware fall on the appliance. The
surface can be damaged.
• Do not activate the cooking zones
with empty cookware or without
cookware.
• Do not put aluminium foil on the
appliance.
• Cookware made of cast iron,
aluminium or with a damaged bottom
can cause scratches on the glass /
glass ceramic. Always lift these
objects up when you have to move
them on the cooking surface.
ENGLISH
7
• Use only stable cookware with the
correct shape and diameter larger
than the dimensions of the burners.
• Make sure cookware is centrally
positioned on the burners.
• Make sure the flame does not go out
when you quickly turn the knob from
the maximum to the minimum
position.
• Use only the accessories supplied
with the appliance.
• Do not install a flame diffuser on the
burner.
• The use of a gas cooking appliance
results in the production of heat and
moisture. Provide good ventilation in
the room where the appliance is
installed.
• Prolonged intensive use of the
appliance may call for additional
ventilation, for example opening of a
window, or more effective ventilation,
for example increasing the level of
mechanical ventilation where present.
• This appliance is for cooking
purposes only. It must not be used for
other purposes, for example room
heating.
• Do not let acid liquids, for example
vinegar, lemon juice or limescale
remover, touch the hob. This can
cause matt patches.
• Discoloration of the enamel or
stainless steel has no effect on the
performance of the appliance.
• Do not spray aerosols in the vicinity of
this appliance while it is in operation.
• Do not place articles on or against the
appliance.
• Do not modify the appliance.
• Do not use or store flammable
materials in the appliance storage
drawer or near the appliance.
• Do not use the appliance as a space
heater.
• Do not let large cookware to
overhang the cooktop onto the
adjacent worktop. It cause scorching
to the worktop surface.
• Do not put cooking pots or pans
close to the controls.
• This appliance complies with the
requirements of Australian Standard
AS5263.1.1.
3.5 Care and cleaning
WARNING!
Do not remove the buttons,
knobs or gaskets from the
control panel. Water may
get inside the appliance and
cause damage.
• Clean regularly the appliance to
prevent the deterioration of the
surface material.
• Deactivate the appliance and let it
cool down before you clean it.
• Disconnect the appliance from the
electrical supply before maintenance.
• Do not use water spray and steam to
clean the appliance.
• Clean the appliance with a moist soft
cloth. Only use neutral detergents. Do
not use any abrasive products,
abrasive cleaning pads, solvents or
metal objects.
• Do not clean the burners in the
dishwasher.
3.6 Disposal
WARNING!
Risk of injury or suffocation.
• Contact your municipal authority for
information on how to discard the
appliance correctly.
• Disconnect the appliance from the
mains supply.
• Cut off the mains electrical cable
close to the appliance and dispose of
it.
• Flat the external gas pipes.
3.7 Service
• To repair the appliance contact an
Authorised Service Centre.
• Use original spare parts only.
3
4
2
1
A
B
D
C
C
D
A
B
www.aeg.com8
4. PRODUCT DESCRIPTION
4.1 Cooking surface layout
4.2 Control knob
Symbol Description
no gas supply / off position
5. DAILY USE
Semi-rapid burner
1
Multi Crown burner
2
Auxiliary burner
3
Control knobs
4
Symbol Description
ignition position / maximum gas supply
minimum gas supply
WARNING!
Refer to Safety chapters.
5.1 Burner overview
A. Burner cap
B. Burner crown
C. Ignition candle
D. Thermocouple
5.2 Ignition of the burner
Always light the burner
before you put on the
cookware.
ENGLISH 9
WARNING!
Be very careful when you use
open fire in the kitchen
environment. The
manufacturer declines any
responsibility in case of the
flame misuse.
1. Push the control knob down and turn
it counterclockwise to the maximum
gas supply position ( ).
2. Keep the control knob pushed for
equal or less than 10 seconds. This
lets the thermocouple warm up. If
not, the gas supply is interrupted.
3. Adjust the flame after it is regular.
If after some tries the burner
does not light, check if the
crown and its cap are in
correct positions.
WARNING!
Do not keep the control
knob pushed for more than
15 seconds. If the burner
does not light after 15
seconds, release the control
knob, turn it into off position
and try to light the burner
again after minimum 1
minute.
The spark generator can
start automatically when you
switch on the mains, after
installation or a power cut. It
is normal.
The hob is supplied with the
progressive valves. They
make the flame regulation
more precise.
5.3 Turning the burner off
To put the flame out, turn the knob to
the off position
WARNING!
Always turn the flame down
or switch it off before you
remove the pans from the
burner.
.
5.4 Using the wok stand
The wok stand lets you use a round
bottomed wok on the hob. Use the wok
stand on the Multi Crown burner only.
When you refit the wok stand, make sure
the recesses on the frame fit securely to
the bars of the pan supports.
CAUTION!
In the absence of electricity
you can ignite the burner
without electrical device; in
this case approach the
burner with a flame, turn the
control knob counterclockwise to maximum gas
supply position and push it
down. Keep the control
knob pushed for equal or
less than 10 seconds to let
the thermocouple warm up.
If the burner accidentally
goes out, turn the control
knob to the off position and
try to light the burner again
after minimum 1 minute.
When you refit the grate of
the Multi Crown burner,
make sure to match the
hollow part of the grate with
the reference located on the
plate fixed to the glass.
www.aeg.com10
6. HINTS AND TIPS
WARNING!
Refer to Safety chapters.
6.1 Cookware
WARNING!
Do not put the same pan on
two burners.
WARNING!
Do not put unstable or
damaged pots on the burner
to prevent from spill and
injury.
CAUTION!
Ensure that pots/pans do
not overhang above the
control knobs, otherwise the
controls may heat up.
CAUTION!
Ensure that pot/pan handles
are out of the reach of
children, by turning them
away from the front edge of
the cooktop.
CAUTION!
Make sure that the pots are
placed centrally on the
burner in order to get
maximum stability and to
get lower gas consumption.
CAUTION!
Liquids spilt during cooking
can cause the glass to break.
6.2 Energy saving
• If it is possible, always put the lids on
the cookware.
• When the liquid starts to boil, turn
down the flame to barely simmer the
liquid.
6.3 Diameters of cookware
Use cookware with
diameters applicable to the
size of burners.
Burner Diameter of
cookware (mm)
Multi Crown 180 - 260
Semi-rapid 120 - 220
Auxiliary 80 - 180
7. CARE AND CLEANING
WARNING!
Refer to Safety chapters.
7.1 General information
• Clean the hob after each use.
• Always use cookware with clean
bottom.
• Scratches or dark stains on the surface
have no effect on how the hob
operates.
• Use a special cleaner applicable for
the surface of the hob.
WARNING!
Do not use knives, scrapers
or similar instruments to
clean the surface of the glass
or between the rims of the
burners and the frame (if
applicable).
• Wash stainless steel parts with water,
and then dry them with a soft cloth.
ENGLISH
11
7.2 Pan supports
The pan supports are not
resistant to washing in a
dishwasher. They must be
washed by hand.
1. Remove the pan supports to easily
clean the hob.
Be very careful when you
replace the pan supports
to prevent the hob top
from damage.
2. The enamel coating occasionally can
have rough edges, so be careful
when you wash the pan supports by
hand and dry them. If necessary,
remove stubborn stains with a paste
cleaner.
3. After you clean the pan supports,
make sure that they are in correct
positions.
4. For the burner to operate correctly,
make sure that the arms of the pan
supports are aligned with the centre
of the burner.
Do not lift the pan supports
at an angle, as this will put
strain on the metal pins. This
can cause damage to the
pins and cause them to
break.
7.3 Removing pan supports
To keep the pan supports in the correct
position, they are put on metal pins
installed in the rear side of the hob. For
easier cleaning, pan supports can be
removed from the hob. Lift up the pan
supports keeping them in horizontal
position as shown in the graphic.
The shape of pan supports and the
amount of burners can be different in
other models of the appliance.
7.4 Cleaning the hob
• Remove immediately: melted plastic,
plastic foil, sugar and food with sugar.
If not, the dirt can cause damage to
the hob. Take care to avoid burns.
• Remove when the hob is sufficiently
cool: limescale rings, water rings, fat
stains, shiny metallic discoloration.
Clean the hob with a moist cloth and
non-abrasive detergent. After
www.aeg.com12
cleaning, wipe the hob dry with a soft
cloth.
•
To clean the enamelled parts, cap
and crown, wash them with warm
soapy water and dry them carefully
before you put them back on.
7.5 Cleaning the spark plug
This feature is obtained through a
ceramic ignition candle with a metal
8. TROUBLESHOOTING
WARNING!
Refer to Safety chapters.
8.1 What to do if...
Problem Possible cause Remedy
There is no spark when you
try to activate the spark generator.
The flame extinguishes immediately after ignition.
The flame ring is uneven. Burner crown is blocked with
The hob is not connected to
an electrical supply or it is
connected incorrectly.
The fuse is blown. Make sure that the fuse is
Burner cap and crown are
placed incorrectly.
Thermocouple is not heated
up sufficiently.
food residues.
electrode. Keep these components well
clean to prevent difficult lighting and
check that the burner crown holes are
not obstructed.
7.6 Periodic maintenance
Speak to your local Authorised Service
Centre periodically to check the
conditions of the gas supply pipe and
the pressure adjuster, if fitted.
Check if the hob is correctly
connected to the electrical
supply.
the cause of the malfunction.
If the fuse is blown again
and again, contact a qualified electrician.
Place the burner cap and
crown correctly.
After lightning the flame,
keep the knob pushed for
equal or less than 10 seconds.
Make sure that the injector is
not blocked and the burner
crown is clean.
8.2 If you cannot find a solution...
If you cannot find a solution to the
problem yourself, contact your dealer or
an Authorised Service Centre. Give the
data from the rating plate. Make sure,
you operated the hob correctly. If not the
servicing by a service technician or
dealer will not be free of charge, also
during the warranty period. The
instructions about the Service Centre and
conditions of guarantee are in the
guarantee booklet.
8.3 Labels supplied with the
MOD.
PROD. NO.
SER.N O
DATA
MOD.
PROD. NO.
SER.N O
DATA
MOD.
PROD.NO.
SER.NO.
03 IT
MADE IN ITALY
TYPE
IP20
0049
A B C
accessories bag
Stick the adhesive labels as indicated
below:
ENGLISH 13
A. Stick it on Guarantee Card and send
this part (if applicable).
B. Stick it on Guarantee Card and keep
this part (if applicable).
9. INSTALLATION
WARNING!
Refer to Safety chapters.
9.1 Before the installation
Before you install the hob, write down
the information bellow from the rating
plate. The rating plate is on the bottom
of the hob.
The bottom of the appliance can get hot.
Ensure a non-combustible separation
panel under the appliance is installed to
prevent access to the bottom.
A clearance of 20mm is required from
the bottom of the appliance to the
separation panel.
Model .......................................
PNC .........................................
Serial number ...........................
C. Stick it on instruction booklet.
Check if the appliance is installed in
accordance with clauses 6.2.5 and
6.10.1.1 of AS/NZS 5601.1:2013, or
clauses 6.10.1 and 6.10.5 of AS/NZS
5601.2:2013 with regard to protection of
a combustible surface near a gas cooking
appliance, and clearances to rangehoods
and exhaust fans.
Clearances to combustible surfaces can
be reduced if combustible surfaces are
protected in accordance with clause
6.10.1.2 of AS/NZS 5601.1:2013, or clause
6.10.2 of AS/NZS 5601.2:2013.
A B C
14
www.aeg.com
9.2 Gas Connection
WARNING!
The following instructions
about installation,
connection and
maintenance must be
carried out by qualified
personnel in compliance
with the local gas fitting
regulations, municipal
building codes, electrical
wiring regulations and other
relevant statutory
regulations, and with
AS/NZS 5601.1 Gas
Installations Part 1: General
Installations, and AS/NZS
5601.2 Gas Installations Part
2: LP Gas installations in
caravans and boats for nonpropulsive purposes, or the
relevant installation code for
gas appliances in your
country.
This appliance is supplied
for use with Natural Gas.
However, it can be
converted for use with LPG
using the installation kit
included.
Make sure that the gas
supply pressure obeys the
recommended values. The
nut at the end of the shaft
connects to the R 1/2"
parallel thread on the elbow
union. The connection is
sealed using the supplied
sealing washer.
Supply pipe sizing
The total hourly gas consumption for the
appliance is shown on the data label.
The required supply pressure (i.e. at inlet
to appliance regulator) for each gas type
is shown on the data label, refer to the
Technical data chapter. Use this
information in conjunction with the
length of run, number of elbows, tees
and bends, the available service pressure
and the supply requirements of other
installed appliances to determine a
suitable pipe size. For assistance in this
matter refer to the appropriate section of
AS/NZS 5601.1 or AS/NZS 5601.2.
An AGA certified class B or D flexible
connection can be used to connect the
cooktop in accordance with AS/NZS
5601.1, in particular section 5.9 and
clause 6.10.1.8, or AS/NZS 5601.2, in
particular section 2.11. Where a hose
assembly is used and the cooktop is in
the installed position, the hose assembly
shall be suitable for connection to a fixed
consumer piping outlet located at a
point 800 – 850mm above the floor and
in the region outside the width of the
appliance to a distance of 250mm. The
point of connection to consumer piping
must be accessible with appliance
installed.
Be careful the hose does not come in
touch with mobile parts or is not
squeezed. Also be careful when the hob
is put together with an oven. Ensure that
the hose assembly is restrained from
accidental contact with the flue outlet of
an underbench oven or any other hot
surface of an adjacent appliance.
Regulator
The regulator must be positioned that
the pressure test nipple is accessible
when the appliance is installed. Connect
the gas supply to the ½ B.S.P. internal
thread inlet of the regulator. Refer to
worktop cut out for connection point
position.
A. End of shaft with nut
B. Washer supplied with the appliance
C. Elbow supplied with the appliance
A
B
A. Outlet
B. Inlet
Assembly of regulator
To assembly the regulator to the
cooktop use the elbow and washer
supplied with the appliance.
The ½" parallel thread connects to the
end of shaft with nut. The washer is
placed between the end of shaft and the
elbow.
The ½" tapered thread connects to the
outlet of the regulator, and is sealed on
the thread. Use thread sealing tape or
thread sealing compound.
The inlet of the regulator is a ½” parallel
thread and is connected to consumer
piping or hose assembly.
The regulators are
configured for use with
Natural Gas. It is not
required to adjust the
regulator to obtain correct
outlet pressure setting.
When the inlet and outlet is
orientated correctly the
arrow on the base of the
regulator indicates the
direction of gas flow.
Checking the gas supply
It takes additional time to
light the gas for the first
time. Air is purged from the
pipes.
ENGLISH
1. Check the manometer zero point is
correct.
2. Connect the manometer to the
cooktop pressure point. It is located
on the regulator.
3. Turn on the gas supply and
electricity, and try to ignite the gas.
4. While the appliance operates check
the outlet pressure:
• when all burners of the appliance
operate at maximum,
• when the smallest burner of the
appliance operates at minimum.
The outlet pressure should
not vary from the nominal
outlet pressure of 1.00kPa by
more than +/–0.20kPa.
Checking the regulator
If the regulator works incorrectly:
• Adjust of upstream regulator if the
outlet and inlet pressure is too low or
an upstream regulator or valve with
insufficient flow capacity is present in
the gas supply line.
Check again the inlet and outlet
pressure, the inlet pressure needs to
be 1.13 - 5kPa.
• Check if the inlet and outlet is
orientated correctly the arrow on the
base of the regulator indicates the
direction of gas flow.
If the regulator still does not
work correctly contact the
After Sales Service.
WARNING!
Check if the hose assembly
is restrained from accidental
contact with the flue outlet
of an oven or any other hot
surface of an adjacent
appliance.
9.3 Gas Conversion
1. Remove the pan supports.
2. Remove the caps and crowns of the
burner.
3. Remove the injectors and replace
them with the ones which are
necessary for the type of gas you use
(see table in "Technical Information"
chapter).
15
A
B
D
C
top hat nut assembly
fully screwed down
turn top
hat nut
anticlockwise
and remove
configuration for
natural gas
HG
F
E
configuration
for LPG
www.aeg.com16
4. Unscrew the top hat nut from the
regulator (B). The top hat nut and
control pressure spring assembly is
disengage as an assembly.
5. Unscrew the threaded pin from top
hat (C).
6. Upturn threaded pin, spring is free
and screw pin back into the top hat
until firm (E).
7. Refit the top hat nut assembly to the
regulator (G), check that it is fully
screwed down. The regulator is now
set for connection to LPG (H).
8. Turn on the gas supply. Use soapy
water to check for leaks. Each
hotplate valve should be turned on,
one at a time, and the injector hole
blanked off for several seconds.
9. The operation of the regulator can
be confirmed by connecting a
manometer to the pressure test point
located on the side of the regulator
body adjacent to the outlet.
While the appliance operates check the
outlet pressure:
• when all burners of the appliance
operate at maximum,
• when the smallest burner of the
appliance operates at minimum.
The outlet pressure should
not vary from the nominal
outlet pressure of 2.60kPa by
more than +/–0.52kPa.
If the regulator works incorrectly:
• Adjust of upstream regulator if the
outlet and inlet pressure is to slow or
an upstream regulator or valve with
insufficient flow capacity present in
the gas supply line.
• Check again the inlet and outlet
pressure, the inlet pressure have to
have 2.75 - 7kPa.
• Check if the insert is fitted correctly.
• Check if the turret screw is fully
screwed down.
• Check if the inlet and outlet is
orientated correctly the arrow on the
base of the regulator indicates the
direction of gas flow.
If the regulator still does not
work correctly contact the
After Sales Service.
A
body
220-240V
ignition box
to burner spark plugs
knob
ignition
switches
E
N
L
DANGER
220-240 volts AC
Disconnect from
supply before
removing panel
ENGLISH
17
9.4 Adjustment of minimum
level
To adjust the minimum level of the
burners:
1. Light the burner.
2. Turn the knob on the minimum
position.
3. Remove the knob.
4. With a thin screwdriver, adjust the
bypass screw position (A).
5. If you change:
• from Natural Gas 1kPa to LPG,
fully tighten the bypass screw in.
• from LPG to Natural Gas 1kPa,
undo the bypass screw
approximately 1/4 of a turn (1/2 of
a turn for Multi Crown burner).
WARNING!
Make sure the flame does
not go out when you quickly
turn the knob from the
maximum position to the
minimum position.
• This appliance is supplied with a
mains cable and a plug.
• Always use a correctly installed
shockproof socket.
• Make sure that there is an access to
the mains plug after the installation.
• Do not pull the mains cable to
disconnect the appliance. Always pull
the mains plug.
• There is a risk of fire when the
appliance is in connection with an
extension cable, an adapter or a
multiple connection. Make sure that
the ground connection agrees with
the standards and regulations.
• Do not let the power cable to heat up
to a temperature higher than 90° C.
Make sure that you connect
the blue neutral cable to the
terminal with a letter "N" on
it. Connect the brown (or
black) phase cable to the
terminal which has a letter
"L". Keep the phase cable
connected at all times.
9.5 Electrical connection
The appliance is supplied with a
standard 7.5 Amp service cord
terminated by a 3-pin plug for
connection to a standard household
socket. The electrical supply is required
to power the electronic ignition system.
To disconnect the electrical
power supply, it is necessary
to service. After installation,
the power point should be
accessible according to local
• Make sure that the rated voltage and
wiring regulations.
type of power on the rating plate
agree with the voltage and the power
of the local power supply.
To prevent contact between
the cable and the appliance
below the hob use the
clamps which are on the side
of the cabinet.
9.6 Connection cable
To replace the connection cable use only
the special cable or its equivalent. The
cable type is: H05SS-FT180.
Make sure that the cable section is
applicable to the voltage and the
working temperature. The yellow / green
earth wire must be approximately 2 cm
longer than the brown (or black) phase
wire.
B
A
min.
650 mm
560
mm
+2
0
C
40 mm
480
mm
+2
0
50 mm
400 mm
B
A
www.aeg.com18
9.7 Assembly
1.
2.
3.
If a furniture unit is
installed at a distance of
400 mm above the hob,
there must be a
minimum safety distance
of 50 mm to the left or
right from the edge of
the hob.
5.
6.
Minimum distances
Dimension mm
A 145
7.
B 128
C 118
Distances shown to
adjacent surfaces are for
the distances to
combustible surfaces. If
the surfaces is not
combustible the
measurements can be
smaller that shown.
4.
A. supplied seal
ENGLISH 19
B. supplied brackets
8.
CAUTION!
Install the appliance only on
a worktop with flat surface.
9.8 Possibilities for insertion
The panel installed below the hob must
be easy to remove and let an easy access
in case a technical assistance
intervention is necessary.
Kitchen unit with oven
The electrical connection of the hob and
the oven must be installed separately for
safety reasons and to let easy remove
oven from the unit.
9.9 Testing appliance operation
WARNING!
Servicing must only be
carried out by an authorised
service person.
After installation, test the appliance and
check if it operates correctly.
1. Turn on the gas and electricity
supply, and attempt ignition on all
burners, separately and in
combination. It takes additional time
to light the gas for the first time. Air
is purged from the pipes.
2. Observe the flame appearance on
each burner. Check the injector size
and supply pressure require if the
flame is much larger or much smaller
than expected. If you can not solve
the problem, contact the After Sales
Service.
3. Check the turndown (minimum or
low) setting on each burner, it may
need adjustment. Valves have a
bypass controlling screw, which you
can accessed by removing the knob.
Bypass are set at the factory for use
on natural gas and should not
require adjustment.
If the appliance is converted to LPG,
screw the bypass in until a small,
stable flame results.
Before any adjustment check the
supply pressure.
4. If you cannot adjust to perform safely
the appliance, inform the customer
of the problem and affix an
appropriate warning notice to the
appliance. Disconnect the appliance
if the fault is dangerous. If a minor
fault exists, the customer may use the
appliance while awaits for the
service.
If you cannot fix the
fault, please contact the
After Sales Service.
5. When the appliance operates
correctly, turn off and instruct the
customer on correct operation
following the User Manual. Check if
the customer understand the
procedure correctly.
10. TECHNICAL DATA
10.1 Overall hob dimensions
Hob dimensions
Width 590 mm
Depth 520 mm
www.aeg.com20
Bench cut-out dimensions
Width 560 mm
Depth 480 mm
10.2 Bypass diameters
BURNER Ø BYPASS 1/100 mm
Multi Crown 57
Semi-rapid 35
Auxiliary 32
10.3 Other technical data
Natural Gas: 1.0 kPa = 37,4 MJ/h
TOTAL POWER:
Electric supply: 220-240 V ~ 50/60 Hz
Gas connection: R 1/2"
Appliance class: 3
Gas replacement:
with Universal LPG:
2.75 kPa
2.60 kPa = 28,5 MJ/h
10.4 Gas burners for NATURAL GAS 1.0 kPa
BURNER GAS CONSUMPTION MJ/h INJECTOR MARK
Multi Crown 14,3 175
Semi-rapid 9,0 135
Auxiliary 5,1 100
10.5 Gas burners for U-LPG 2.60 kPa
BURNER GAS CONSUMPTION MJ/h INJECTOR MARK
Multi Crown 12,4 96A
Semi-rapid 6,4 71
Auxiliary 3,3 50
12. ENVIRONMENTAL CONCERNS
ENGLISH 23
Recycle materials with the symbol .
Put the packaging in relevant containers
to recycle it. Help protect the
environment and human health by
recycling waste of electrical and
electronic appliances. Do not dispose of
appliances marked with the symbol
with the household waste. Return the
product to your local recycling facility or
contact your municipal office.
*
FOR SALES IN AUSTRALIA AND NEW ZEALAND
Warranty
ALL AEG BRANDED APPLIANCES
This document sets out the terms and conditions of the product warranties for
AEG Appliances. It is an important document. Please keep it with your proof
of purchase documents in a safe place for future reference should there be a
manufacturing defect in your Appliance. This warranty is in addition to other
rights you may have under the Australian Consumer Law.
1. In this warranty:
(a) ‘ACL’ or ‘Australian Consumer Law’ means Schedule 2 to the Competition and
Consumer Act 2010;
(b) ‘Appliance’ means any Electrolux product purchased by you and accompanied
by this document;
(c) ‘ASC’ means Electrolux’s authorised serviced centres;
(d) ‘AEG’ is the brand controlled by Electrolux Home Products Pty Ltd of 163
O’Riordan Street, Mascot NSW 2020, ABN 51 004 762 341 in respect of
Appliances purchased in Australia and Electrolux (NZ) Limited (collectively
“Electrolux”) of 3-5 Niall Burgess Road, Mount Wellington, in respect of
Appliances purchased in New Zealand;
(e) ‘ Warranty Period’ means the period specified in clause 3 of this warranty;
(f ) ‘you’ means the purchaser of the Appliance not having purchased the
Appliance for re-sale, and ‘your’ has a corresponding meaning.
2. Application: This warranty only applies to new Appliances, purchased and used
in Australia or New Zealand and is in addition to (and does not exclude, restrict, or
modify in any way) other rights and remedies under a law to which the Appliances
or services relate, including any non-excludable statutory guarantees in Australia
and New Zealand.
3. Warranty Period: Subject to these terms and conditions, this warranty continues
for in Australia for a period of 60 months and in New Zealand for a period of 60
months, following the date of original purchase of the Appliance.
4. Repair or replace warranty: During the Warranty Period, Electrolux or its ASC
will, at no extra charge if your Appliance is readily accessible for service, without
special equipment and subject to these terms and conditions, repair or replace
any parts which it considers to be defective. Electrolux may, in its absolute
discretion, choose whether the remedy oered for a valid warranty claim is repair
or replacement. Electrolux or its ASC may use refurbished parts to repair your
Appliance. You agree that any replaced Appliances or parts become the property
of Electrolux.
5. Travel and transportation costs: Subject to clause 7, Electrolux will bear the
reasonable cost of transportation, travel and delivery of the Appliance to and from
Electrolux or its ASC. Travel and transportation will be arranged by Electrolux as
part of any valid warranty claim.
6. Proof of purchase is required before you can make a claim under this warranty.
7. Exclusions: You may not make a claim under this warranty unless the defect claimed
is due to faulty or defective parts or workmanship. This warranty does not cover:
(a) light globes, batteries, filters or similar perishable parts;
(b) parts and Appliance s not supplied by Electrolux;
(c) cosmetic damage which does not aect the operation of the Appliance;
(d) damage to the Appliance caused by:
(i) negligence or accident;
(ii) misuse or abuse, including failure to properly maintain or service;
(iii) improper, negligent or faulty servicing or repair works done by
anyone other than an Electrolux authorised repairer or ASC;
(iv) normal wear and tear;
(v) power surges, electrical storm damage or incorrect power supply;
(vi) incomplete or improper installation;
(vii) incorrect, improper or inappropriate operation;
(viii) insect or vermin infestation;
(ix) failure to comply with any additional instructions supplied with
the Appliance;
In addition, Electrolux is not liable under this warranty if:
(a) the Appliance has been, or Electrolux reasonably believes that the Appliance
has been, used for purposes other than those for which the Appliance was
intended, including where the Appliance has
been used for any non-domestic purpose;
(b) the Appliance is modified without authority from Electrolux in writing;
(c) the Appliance’s serial number or warranty seal has been removed
or defaced.
8. How to claim under this warranty: To enquire about claiming under this warranty,
please follow these steps:
(a) carefully check the operating instructions, user manual and the terms of
this warranty;
(b) have the model and serial number of the Appliance available;
(c) have the proof of purchase (e.g. an invoice) available;
(d) telephone the numbers shown below.
9. Australia: For Appliances and services provided by Electrolux in Australia: Electrolux
goods come with guarantees that cannot be excluded under the Australian
Consumer Law. You are entitled to a replacement or refund for a major failure and
for compensation for any other reasonably foreseeable loss or damage. You are also
entitled to have the Appliance repaired or replaced if the Appliance fails to be of
acceptable quality and the failure does not amount to a major failure. ‘Acceptable
quality’ and ‘major failure’ have the same meaning as referred to in the ACL.
10. New Zealand: For Appliances and services provided by Electrolux in New
Zealand, the Appliances come with a guarantee by Electrolux pursuant to the
provisions of the Consumer Guarantees Act, the Sale of Goods Act and the Fair
Trading Act. Where the Appliance was purchased in New Zealand for commercial
purposes the Consumer Guarantee Act does not apply.
11. Confidentiality: You accept that if you make a warranty claim, Electrolux and
its agents including ASC may exchange information in relation to you to enable
Electrolux to meet its obligations under this warranty.
Before calling for service, please ensure that the steps listed in clause 8 above have been followed.
FOR SERVICE
or to find the address of your nearest
authorised service centre in Australia
PLEASE CALL 1300 363 664
OR EMAIL
customercare@aegaustralia.com.au
For the cost of a local call (Australia only)
FOR SERVICE
or to find the address of your nearest
authorised service centre in New Zealand
PLEASE CALL 0800 234 234
OR EMAIL customercare@electrolux.co.nz
(New Zealand only)
AEG_Warr_May17
Important Notice
SERVICE AUSTRALIA
aeg.com/au
SERVICE NEW ZEALAND
aegnewzealand.co.nz
FOR SPARE PARTS
or to find the address of your nearest
spare parts centre in Australia
PLEASE CALL 13 13 50
OR EMAIL
customercare@aegaustralia.com.au
For the cost of a local call (Australia only)
FOR SPARE PARTS
or to find the address of your nearest
spare parts centre in New Zealand
PLEASE CALL 0800 10 66 20
OR EMAIL customercare@electrolux.co.nz
(New Zealand only)
www.aeg.com/shop
867334758-B-262017
Loading...