AEG 8259 S, 825 D User Manual

825 D / 8259 D

Dunstabzugshaube Fume Extractor Hood Hotte aspirante Afzuigkap Cappa aspirante

Montage- und Gebrauchsanweisung Installation and Operating Instructions Instructions de montage et mode d'emploi Montage- en gebruiksaanwijzing Istruzioni di montaggio ed istruzioni per l'uso

БрпсспцзфЮсбт хдсбфмюн

Contents

Introduction 20

Extractor version 20

Filter version 21

Electrical connections 22

Safety warnings for electrician 22

Technic Details 23

Installation 24

Safety warnings for kitchen unit installer 24

Installation 26

Hood Operation 28

Safety warnings for user 29

Maintenance and care 30

Metal grease filter 30

Open the metal grease filter 30

Carbon filter 31

Changing the light bulb 32

Cleaning 33

Special accessories 33

Technical assistance service 33

Printed on recycled paper.

AEG  putting words into action.

Introduction

Extractor version

●The hood is supplied as an extractor unit and can also be used with

a filtering function by fitting activated carbon filters (special

accessory).

● You will need original AEG activated carbon filters for this function

(see Special Accessories).

● The air is forced out through a hose fitted to the top of the hood

A. Fig. 1.

● The outlet hose must have a diameter of 120 mm (special

accessory) for the filtering version.

● Fit the connection ring above the hood with two screws then fir an

exhausting pipe long enough to reach the outside. Fig. 1.

Fig. 1

● If the cooking vapour is passed through an outside wall, you will

need an MKZ telescopic wall pipe (with intake and ventilation) E-

Nr.: 610 899 004 (120 mm Ø) from our range of special

accessories.

Filter version

● The air is filtered through an activated carbon filter and passed back

into the kitchen through the top outlet duct grids.

● You will need an original AEG KF 825 activated carbon filter for the

filtering function. (See Special Accessories).

● Fix the deflector with two screws Ø3,5x6,5. Fig. 2.

Fig. 2

Electrical connections

Safety warnings for electrician

It must be ensured that the voltage and current indicated on the rating plate

agree with the voltage of the user to electricity supply.

If the appliance has been equipped with a mains lead with a moulded-on type plug,

the following regulations must be comply with:

The plug moulded on to the lead incorporates a fuse. For replacement, use a 5

amp BS1362 fuse. Only ASTA approved or certified fuses should be used. If the

fuse cover/carrier is lost, a replacement cover/carrie must be obtained from an

electrical goods retailer. If the socket outlets are not suitable for the plug fitted to

the appliance, then the plug must be cut off and destroyed for safety reasons, and

an appropriate plug be fitted.

When wiring the plug ensure that all strands of wire are securely retained in each

terminal. Do not forget to tighten the mains lead clamp on the plug.

Electrical connections

230 V - using fixed power supply line with plug.

240 V - using fixed power supply line (Great Britain).

Fuse rating 13 amps

(The unit should only be connected up by an authorized electrician).

See rating plate for further information.

It is recommended that the socket for the plug is sited above the cooker hood

or above the overhead cabinet.

This has 2 advantages:

1) The socket is not visible.

2) The appliance can easily be unplugged when necessary.

If a fixed connection is required the cooker hood should be connected by an

electrical installer registered with a competent electricity company. An isolating

device is to be provided on the fixed wiring side. Switches with a contact opening

of more than 3mm apply as isolating devices.

These include-automatic cut-out switches, fuses and contactors (VDE 0730, s.

7, Part1).

Electrical connection for the UK

Appliances with 2 wires

The appliance must be connected to fixed wiring with a double

pole switched fused spur outlet with or without pilot lamp.

We strongly recommend the appliance to be connected only by a

qualified electrician who is a member of the NICEIC who will com-

ply with the IEE and any local regulations.

NOTE:

The terminology DOUBLE POLE means that both the live and the

neutral supplies are switched and disconnected at the same time.

The terminations labelled SUPPLY are for the connection for the

internal house wiring and the terminations labelled LOAD are for

the appliance.

IMPORTANT

The wires of the mains lead supplied with this appliance are

coloured in accordance with the following code:

Blue-Neutral

Brown-Live

As the colours of the flexible cord of this appliance may not

correspond with the coloured markings identifying the ter-

minals in the plug, proceed as follows: The wire which is col-

oured brown must be connected to the terminal which is

marked with the letter L or coloured red.

The wire which is coloured blue must be connected to the

terminal which is marked with the letter N or coloured black.

BLUE

(NEUTRAL)

BROWN

(LIVE)

FUSE

LOAD

SUPPLY

LOAD

SUPPLY

DP 13A, 250V

+ 11 hidden pages