Page 1
Page 2
aee.com
[ 1 ]
[ 2 ]
[ 6 ]
[ 7 ]
[ 8 ]
[ 9 ]
[ 10 ]
[ 3 ]
[ 4 ]
[ 5 ]
[ 11 ]
[ 12 ]
[ 13 ]
[ 14 ]
[ 15 ]
[ 16 ]
[ 17 ]
[ 18 ]
[ 1
[ 2
[ 3
[ 4
[ 5
AEE AP9 Quick Start Guide
Disclaimer
Please read this disclaimer carefully before using the product of Quadcopter. This product is not suitable for people under the age of 18. By using this product,
you hereby agree to this disclaimer and signify that you have read them fully. You agree that you are responsible for your own c onduct and content while using this
product, and for any consequences there of. You agree to use this product only for purposes that are proper and in accordance with the terms and any applicable or
guidelines AEE may make available.
1. Any part of this disclaimer is subject to change without prior notice; refer to HYPERLINK www.aee.com for the latest version.
2. AEE Technology reserves the right of nal interpretation of this disclaimer.
3. This disclaimer is made in various language versions; in the event of divergence among different versions, Chinese version shall prevail.
Instructions
[ 1 ] Antenna
[ 2 ] Speed Switch S1
[ 3 ] Calibration Switch S2
[ 4 ] 3-Position Switch S3
[ 5 ] Flight Mode Switch S4
[ 6 ] Power Indicator
[ 7 ] Status Indicator
[ 8 ] Left Joystick
[ 9 ] Video Recording(Reserved function)
[ 10 ] Shutter Button(Reserved function)
[ 11 ] Video Recording Indicator
[ 12 ] Strap hole
[ 13 ] Right Joystick
[ 14 ] Video Stop Button (Reserved function)
[ 15 ] Power Switch
[ 16 ] Battery Compartment
Note:
[ 17 ] Hook open/close button
[ 18 ] Return button
Left Joystick ("Up & Down" controls Throttle, " Left & Right" controls Yaw)
Right Joystick ("Left & Right ” controls Roll, "Front & Back" controls Pitch)
Operating Instructions
Remote Control
(U.S. Mode)
Quadcopter Direction
(" " indicates nose direction)
[ 6 ]
[ 1 ] Propeller [ 2 ] Motor [ 3 ] Front Indicator
[ 4 ] Camera Cage [ 5 ] Landing Gear [ 6 ] Quadcopter Battery
[ 7 ] Tail Indicator [ 8 ] Power switch
[ 9 ] Battery Level LCD Segment Display [ 10 ] Rear Indicator
[ 11 ] Battery Level Check button
Switch on the Remote Control
1. Load four A A batteries into the battery compar tment. Pay attention to positive
and negative directions.
2. Be sure S1 is swiched to the “E” position , S2 and S4 are switched to the
upper-most position .
3. Slide power switch to ON position to power on the Remote Control. Then the
power indicator(red) lights up:
[ 7 ]
[ 8 ]
[ 9 ]
[ 10 ]
[ 11 ]
LT
LV
ET
Install the Camera and Cage
The camera cage named Q45 can be mounted on A P9 aircraft for S50/S51/S60/
S71/OM51S/OM60S/OR60S/OR71S/S40 and other S series of cameras .
1.Put the camera in the cage.
2.Assembly the cage on the Quadcopter with the screw.
Assembling Quadcopter Battery
1. Load battery into battery compartment in the correct direction.
2. Ensure that the battery has been completely pushed in:
]
]
]
]
]
Impor tant: 1. Please check the battery level before take- off; when the
batter y level detection button is short pressed, the bat tery level will appear in
percentage on the display. 2. When the bat tery icon has less than two bars,
please charge the batter y fully before take-off.
Turn on the AP9
1. Place AP9 on a at and open ground, with the tail indicator facing toward you.
1
Page 3
2. Power on the Remote control and Quadcopter in sequence.
Note: The table below gives partial descr iption of the indicators.
For detailed description, please see the User Manual:
Tai l
indicator
Description Power-on
self-test
(off)
Searching
satellites
(blinking slowly)
Remote Control Indicators
Functional
Status
Power indicator Status indicator
Power on Remaining on / /
GPS OK Remaining on Green light /
LT
LV
GPS
searching
Remaining on Blue light /
ET
WARNI NG Front Indicator(green) Rear Indicator(red)
1st Level low
battery alarm
Slow Blink(1s ON, 1S OFF) Slow Blink(1s ON, 1S OFF)
2nd Level low
battery alarm
Fast blink twice per second Fast blink twice per second
Searching
completed
(remaining on)
Photo shooting &
video recording
indicator
aee.com
Note:1. Propellers are designed to self-tighten during ight; therefore do not
tighten them excessively. Do not use glue on the threads. 2. Ensure Propellers
are attached in the correct position. The quadc opter cannot y properly if the
Propellers are installed incorrectly. Wear protective gloves while installing as
Propellers are very thin and may cause accidental scratches.
Taking off and Landing(Outdoors)
Taking off:
1. Place Quadcopter (with full power battery) on a at and open ground, and
ensure Tail Indicator fac es toward you.
2. Turn on the Remote Control and the Quadcopter switch.
3. Be sure the Remote control is set exactly as the gure below.
Calibrate the Compass
Compass calibration is required before rst time use other wise the system
may not work properly, affecting ight safety. The compass is sensitive to
electromagnetic interference from other electronic devices, which can cause
abnormal compass data leading to poor ight performance or even ight failure.
Regular calibration is required for optimum performance.
● Attention:Do not c alibrate the compass in environments with a strong
magnetic eld (such as near power lines or radio towers); Do not carry
ferromagnetic materials when calibrating the compass,such as keys and cell
phones etc.)
1 2 3
GPS
NRM
NULL
S4
After the quadcopter
powers on(about 20
seconds). Swich S4 for
more than 5 times between
GPSand F-M mode and
stay at NRM position. The
quadcopter will enter
calibraion standby mode
(the tail light blinks fast).
4 5
Toggle the joysticks to the
position as shown above,
Front indic ator (green)
starts blinking, Then
release the joysticks.
Compass calibration
command has been sent
successfully.
Rotate
Quadcopter 360°
horizontally (2
turns)
4. Starting motors: toggle the lef t joystick to lef t bottom corner and toggle right
joystick to right bottom corner at the mean time to start motors. Once the
motors st art please release the joysticks immediately.
5. Push the left joystick slowly, then Quadcopter take off. Please refer AEE
Quadcopter User Manual for more details.
Note: The motors can not be started until GPS signal is ready(Tail indic ator
will remain on while GPS signal is ready).
Landing:
GPS
NRM
S1 S2
S3 S4
NULL
1. Slowly pull the left joystick to lower Quadcopter until four land-gear s touch
the ground (only on at and open ground).
2. After landing, pull the left joystick to the lowest position and hold for more
than 3 seconds until the motors stop.
3. Power off Quadcopter by sliding the switch to OFF.
4. Remove the batter y.
5. Power off Remote Control .
Note:
Toggle Left joystick to left
bottom corner.
Toggle Right joystick to r ight
bottom corner.
Rotate Quadcopter 360°
vertically 2 turns (Nose
down )
Rotate Quadcopter vertically (Nose leftward)
until green lights off, Put Quadcopter on the
ground. Green lights up normally af ter light
off→ calibration successful; Green lights
blink fast after light off→calibration failed
→Recalibrate
Note: 1.Calibration can begin until the Remote Control and Quadcopter
start up completely(powered on for about 20 seconds).2.Please disassemble the
propellers before calibration.
Assembling Propellers
1. Remove the 4 warning cards from motors.
2. Attach Propellers with gray nuts to motor shafts without " P" marks, and
attach Propellers with black nuts to motor shafts with "P" marks.
3. Tighten Propellers as per the appropriate locking direction.
Important:
1. Control the ight height under your control dur ing your rst ight.
2. Do not stop the motors during ight, O R it will cause the Q uadcopter to drop
without control.
2
Page 4
Loading...