Advantek Networks AWN-USB-11N2 User Manual
Wireless – N USB Adapter
User’s Manual
Model # AWN-USB-11N2
FCC Warning
This equipment has been tested and found to comply with the limits for a Class C digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and u sed in a ccordan ce with
the instructions, may cause harmful interference to radio communication. Howe ver, there i s no
guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television recep tion, which ca n be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which
- Consult the dealer or an experienced radio/TV technician for help. the receiver is
connected.
FCC Caution: Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with a minimum distance of
about eight inches (20cm) between the radiator and your body.
This transmitter must not be co-located or operated in conjunction with any other antenna or
transmitter.
Modular Approval Statement:
This device is intended to be used only for OEM integrator under the following conditions:
1) The antenna must be installed such that 20 cm is maintained between the antenna and
users, and
2) The transmitter module may not be co-located with any other transmitter or antenna.
1
IMPORTANT NOTE:
In the event that these conditions cannot be met (for example certain laptop configurations or
co-location with another transmitter), then the FCC authorization is no longer considered valid
and the FCC ID cannot be used on the final product. In these circumstances, the OEM
integrator will be responsible for re-evaluating the end product (including the transmitter) and
obtaining a separate FCC authorization.
Revision History
Revision History
V2.0 Second release
All brand and product names mentioned in this manual are trademarks and/or registered
trademarks of their respective holders.
2
Contents
1.INTRODUCTION................................................................................................... 4
1.1 FEATURES ..................................................................................................... 4
1.2 LEDINDICATOR ............................................................................................. 4
1.3 PACKAGECONTENTS ....................................................................................... 4
2.SOFTWAREINSTALLATION .................................................................................. 5
3.WIRELESSLANUTILITY ...................................................................................... 12
3.1 GENERAL .................................................................................................... 12
3.2 PROFILE ..................................................................................................... 12
3.3 AVAILABLENETWORK.................................................................................... 13
3.4 STATUS ...................................................................................................... 15
3.5 STATISTICS .................................................................................................. 15
3.6 WI‐FIPROTECTSETUP ................................................................................... 16
4.SOFT‐APFUNCTION........................................................................................... 17
4.1 SWITHTOAPMODE ..................................................................................... 17
4.2 GENERAL .................................................................................................... 18
4.3 ADVANCED ................................................................................................. 19
4.4 STATISTICS .................................................................................................. 19
4.5 ICS ........................................................................................................... 20
3
1. Introduction
This is a wireless 11n USB Adapter that provides unsurpassed wireless performance for your
Desktop PC or Notebook. It complies with IEEE 802.11n draft 2.0 wireless standard and is
backward compatible with IEEE 802.11b/g. This USB adapter provides better wireless
reception and up to 150/300 Mbps data transfer rates in 11n mode. With this adapter, you
can easily upgrade your Desktop PC or Notebook wireless connectivity. Once connected, to
access the network with high-speed Internet connection while sharing photos, files, music,
video, printers, and storage. Get a better Internet experience with a faster wireless
connection so you can enjoy smooth digital phone calls, gaming, downloading, and video
streaming.
The Wireless USB adapter provides peer-to-peer communication among any compatible
wireless client users and no Access Point required. It also supports WEP, WPA, WPA2,
WPS, 802.1x high-level WLAN security features that guarantee the best security for users.
1.1 Features
‧ Complies with draft IEEE 802.11n standard
‧ Up to 150/300 Mbps data transfer rates in IEEE 802.11n mode
‧ Backward compatible with IEEE 802.11b/g
‧ Legacy and High Throughput Modes
‧ Supports 64/128-bit WEP Data Encryption
‧ Supports WPA, WPA2 (802.11i), WPS, 802.1x advanced security
‧ Supports Quality of Service (QoS) - WMM, WMM-PS
‧ Supports both Infrastructure and Ad-Hoc Networking Modes
‧ Supports Multiple BSSID
‧ Simple user setup and diagnostics utilities
1.2 LED Indicator
LED Light Status Description
ACT Blinking
Data is being transmitted or received
1.3 Package Contents
‧ One Wireless USB Adapter
‧ One USB A-type Extension Cable
‧ One Installation CD (Drivers, Utility, User’s Manual)
4
2. Software Installation
Note: The following installation was operated under Windows 7. (Procedures will be
same for Windows Vista, XP and 2000 Operation System)
Step1: Insert the Wireless USB adapter into the USB slot of your computer. The system will
automatically find the device and search for its driver.
For Windows 7
Î Windows System will pup-up the message for new searched device.
For Windows Vista/XP/2000
Î Please click Cancel to continue.
5
Step2: Insert Wireless USB Adapter Installation CD into CD-ROM drive then windows below
will appear. Click Install Driver & Utility to begin device driver installation.
Step3: Select the language for this installation from the choices below and click Next> to
continue.
6
Loading...