WISE-2400-User Manual
PRODUCT INTRODUCTION
1. Package Contents
Before you start using this product, please check if there is anything
missing in the package and contact your dealer to claim the missing
item(s):
BLE/ Wi-Fi Intelligent Sensor Gateway (WISE-2400)
USB Cable (60cm)
User Manual
USB Adapter 5V/1A
2. LED & Button Definitions
Front Panel
LEDs
Color
Status
Description
Power Status
Blue
ON
Power on
OFF
Power off
Active Status
Blue
BLINK
Data Transmission
Red
BLINK
Data Transmission failed
Items
Description
Power ON/OFF
Micro USB Port
USB Power connector
Rear Panel
3. Hardware Installation
Step 1: Connect the power adapter to the WISE-2400
Plug one end of the power adapter into a power outlet and connect the
other end to the 5V interface of the device.
1
Step 2: Fixed WISE-2400 with mounting kit
Please follow below steps. to mount the WISE-2400.
2
4. GETTING STARTED
A. First 2400 setting
Start to use WISE-2400, please follow below flowchart to do the setting.
3
B. WISE-2400 Default Setting
Config
Value
Description
SSID
WISE_AP
SSID of Connect AP
security key
12345678
Security key of connected AP
security type
WPA/WPA2
Security type of connected AP
Server IP
192.168.2.58
Server port
4242
WISE-2200W port
7000
For remote config connection
Battery low power alert
40
Send alert if battery is low power
RTLS Operation on/off
off
Turn on/off RTLS function
Operation mode
client
Switch operation mode of RTLS
Scan interval
10
Setting scan interval of RTLS function
G-sensor sensitivity
off
Turn on/off G-sensor and set sensitivity(2G~16G),
RTLS data will be sent if G-sensor is triggered
Wifi AP config
Key
Config
Note
SSID
WISE_AP
key
12345678
Security type
WPA
RTLS Server config
IP
192.168.2.58
port
4242
Factory default
WISE-2400 default config as following table. Please follow the setting item to
match wifi and RTLS server setting environment.
C. WISE-2400 connection
Start the RTLS server with Wifi AP, then open WISE-2400 and WISE-2200B ,
WISE-2400 will be automatically registered to the RTLS server.
4
Can check all the WISE-2200B status from RTLS server "DEVICE
MANAGEMENT "function.
5
Federal Communications Commission (FCC) Statement
15.21
You are cautioned that changes or modifications not expressly approved by the part responsible for compliance
could void the user’s authority to operate the equipment.
15.105(b)
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part
15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
1) this device may not cause interference and
2) this device must accept any interference, including interference that may cause undesired operation of the
device.
RF Radiation Exposure Statement:
1. This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
2. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with a minimum distance of 20 centimeters between the
radiator and your body.
6
Loading...