Advantech Co TREK674 User Manual
User Manual
TREK-674
Computer
Copyright
The documentation and the software included with this product are copyrighted
2010 by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd.
reserves the right to make improvements in the products described in this
manual at any time without notice. No part of this manual may be reproduced,
copied, translated or transmitted in any form or by any means without the prior
written permission of Advantech Co., Ltd. Information provided in this manual is
intended to be accurate and reliable. How- ever, Advantech Co., Ltd. assumes
no responsibility for its use, nor for any infringements of the rights of third
Acknowledgement s
Product Warranty (2 years)
TREK-674 User Manual
parties, which may result from its use.
Intel and Atom are trademarks of Intel Corporation. Microsoft Windows and
MS-DOS are registered trademarks of Microsoft Corp. All other product
names or trademarks are properties of their respective owners.
Advantech warrants to you, the original purchaser, that each of its products will
be free from defects in materials and workmanship for two years from the date
of purchase.
This warranty does not apply to any products which have been repaired or
altered by persons other than repair personnel authorized by Advantech, or
which have been subject to misuse, abuse, accident or improper installation.
Advantech assumes no liability under the terms of this warranty as a
consequence of such events.
Because of Advantech’s high quality-control standards and rigorous testing,
most of our customers never need to use our repair service. If an Advantech
product is defective, it will be repaired or replaced at no charge during the
warranty period. For out- of-warranty
cost
of replacement materials, service time and freight. Please consult your
dealer for more details.
If you think you have a defective product, follow these steps:
1. Collect all the information about the problem encountered. (For example,
CPU speed, Advantech products used, other hardware and software used,
etc.) Note anything abnormal and list any onscreen messages you get
when the problem occurs.
2. Call your dealer and describe the problem. Please have your manual,
product, and any helpful information readily available.
3. If your product is diagnosed as defective, obtain an RMA (return
merchandise authorization) number from your dealer. This allows us to
process your return more quickly.
4. Carefully pack the defective product, a fully-completed Repair and
Replacement Order Card and a photocopy proof of purchase date (such as
your sales receipt) in a shippable container. A product returned without
proof of the purchase date is not eligible for warranty service.
5. Write the RMA number visibly on the outside of the package and ship it
prepaid to your dealer.
repairs, you will be billed according to the
ii
Declaration of Conformity
This product has passed the WES8 test for environmental specifications.
Test conditions for passing included the equipment being operated within
an industrial enclosure.
damaged by ESD
strongly recommend the use of CE-compliant industrial enclosure
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference and
(2) this device must accept any interference received, including interference that
may cause undesired operation. “Complies with CANADA RSS-210
FCC Part 15.21 information for user
You are cautioned that changes or modifications not expressly approved by the
party responsible for compliance could void your authority to operate the
equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) this device may not cause harmful interference and
(2) this device must accept any interference received, including interference that
may cause undesired operation
Notes and Warnings to the User and Installer:
products.
FCC Class B
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference
will not occur in a
harmful interference to radio or television reception, which can be
determined by turning the equipment off
to try to correct the interference by one or more of the following
measures:
!
!
!
!
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
particular installation. If this equipment does cause
In order to protect the product from being
(Electrostatic Discharge) and EMI leakage, we
and on, the user is encouraged
Caution:
This Installation Guide is intended for use by the professional wireless LAN
system installer.
The device cannot be sold retail, to the general public or by mail order. It must be
sold to dealers or have strict marketing control.
Warning: It is the responsibility of the professional installer to ensure that the
system is used exclusively for fixed, point-to-point
operations.
Warning: When using the device in the United States (or where FCC rules apply),
it is the responsibility of the professional installer
to ensure to control the output power not greater then the application.
Who Should Use this Guide:
Installation of this device should be accomplished only by a qualified wireless LAN
system installer who is: -Knowledgeable of the use, installation and configuration
procedures and associated networking components. -Knowledgeable of each
system component’s equipment User and Installation Guide. -Knowledgeable of
the
installation and configuration procedures for the site’s network infrastructure
system and wiring.
-Knowledgeable of the installation procedures, safety, and code requirements for
the site’s antenna, antenna mast, antenna cabling, and installation. We highly
recommend that the antenna installation be performed by a qualified antenna
installation Professional.
Users should not attempt to make such connections themselves, but should
contact the appropriate electrical inspection authority, or
electrician, as appropriate.
1. This Transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
2. This equipment complies with FCC RF radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with a
minimum distance of 20 centimeters between the radiator and your body.
In the users manual of the end product, the end user has to be informed to keep at least
20cm separation with the antenna while this end product is installed and operated. The
end user has to be informed that the FCC radio-frequency exposure guidelines for an
uncontrolled environment can be satisfied. The end user has to also be informed that any
changes or modifications not expressly approved by the manufacturer could void the
user's authority to operate this equipment.
Technical Support and Assistance
1. Visit the Advantech web site at
latest information about the product.
2. Contact the distributor, sales representative, or Advantech's customer
service center for technical support if you need additional assistance.
Please have the following information ready before you call:
–
Product name and serial number
–
Description of your peripheral attachments
–
Description of your software (operating system, version, application
software, etc.)
–
A complete description of the problem
–
The exact wording of any error messages
www.advantech.com/support
for the
Warnings, Cautions and Notes
Warning!
personal
Warnings indica te conditions, which if not observed, can cause
Injury!
Caution!
Document Feedback
Packing List
Note! Notes provide optional additional information.
To assist us in making improvements to this manual, we would welcome
comments and constructive criticism. Send all such in writing to:
support@advantech.com
Before setting up, check that the items listed below are included, in good
condition. If any item does not accord with the table, please contact your dealer
immediately.
!
!
!
!
!
!
“
losing data. e.g.
There is a danger of a new battery exploding if it is incorrectly
installed. Do not attempt to recharge, force open , or heat the battery.
Replace the battery only with the sa me or e quivalen t type
recommended by the manufacturer. Discard used batteries according
to the manufacturer's instructions.
TREK-674 series Computing Box
Accessories for TREK-674
Warranty card
Power cord: DC power inlet cable
Videio in/CAN cable
Drivers, Utilities and User Manual" CD-ROM
Cautions are included to h e lp you avoid damaging hardware or
Safety Instru c t ions
1. Read these safety instructions carefully.
2. Keep this User Manual for later reference.
3. Disconnect this equipment from any AC outlet before cleaning. Use a
damp cloth. Do not use liquid or spray detergents for cleaning.
4. For plug-in equipment, the power outlet socket must be located near the
equipment and must be easily accessible.
5. Keep this equipment away from humidity.
6. Put this equipment on a reliable surface during installation. Dropping it or
letting it fall may cause damage.
7. The openings on the enclosure are for air convection. Protect the
equipment from overheating. DO NOT COVER THE OPENINGS.
8. Make sure the voltage of the power source is correct before
connecting the equipment to the power outlet.
9. Position the power cord so that people cannot step on it. Do not place
anything over the power cord.
10. All cautions and warnings on the equipment should be noted.
11 . If the equipment is not used for a long time, disconnect it from the power
source to avoid damage by transient overvoltage.
12. Never pour any liquid into an opening. This may cause fire or electrical
shock.
13. Never open the equipment. For safety reasons, the equipment
14. If one of the following situations arises, get the equipment checked by
15. The power cord or plug is damaged.
16. Liquid has penetrated into the equipment.
17. The equipment has been exposed to moisture.
18. The equipment does not work well, or you cannot get it to work according
19. The equipment has been dropped and damaged.
20. The equipment has obvious signs of breakage.
21. DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT WHERE THE
22.
23. The sound pressure level at the operator's position according to IEC
704-1:1982 is no more than 70 dB (A).
DISCLAIMER: This set of instructions is given according to IEC 704-1.
Advantech disclaims all responsibility for the accuracy of any statements
contained herein.
should be opened only by qualified service personnel.
service personnel:
to the user's manual.
STORAGE TEMPERATURE MAY GO BELOW -30° C (-22° F) OR ABOVE 70° C
(158° F). THIS COULD DAMAGE THE EQUIPMENT. THE EQUIPMENT
SHOULD BE IN A CONTROLLED ENVIRONMENT.
Operating temperature: 50° C
CAUTION: DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY
REPLACED. REPLACE ONLY
TYPE RECOMMENDED BY THE MANUFACTURER, DISCARD USED
BATTERIES ACCORDING TO THE MANUFACTURER'S
INSTRUCTIONS.
WITH THE SAME OR EQUIVALENT
Wichtige Sicherheishinweise
1. Bitte lesen sie Sich diese Hinweise sorgfältig durch.
2. Heben Sie diese Anleitung für den späteren Gebrauch auf.
3. Vor jedem Reinigen ist das Gerät vom Stromnetz zu trennen. Verwenden
Sie Keine Flüssig-oder Aerosolreiniger. Am besten dient ein
angefeuchtetes Tuch zur Reinigung.
4. Die NetzanschluBsteckdose soll nahe dem Gerät angebracht und
leicht zugänglich sein.
5. Das Gerät ist vor Feuchtigkeit zu schützen.
6. Bei der Aufstellung des Gerätes ist auf sicheren Stand zu achten. Ein
Kippen oder Fallen könnte Verletzungen hervorrufen.
7. Die Belüftungsöffnungen dienen zur Luftzirkulation die das Gerät vor
überhit- zung schützt. Sorgen Sie dafür, daB diese Öffnungen nicht
abgedeckt werden.
8. Beachten Sie beim. AnschluB an das Stromnetz die AnschluBwerte.
9. Verlegen Sie die NetzanschluBleitung so, daB niemand darüber fallen
kann. Es sollte auch nichts auf der Leitung abgestellt werden.
10. Alle Hinweise und Warnungen die sich am Geräten befinden sind zu
beachten.
11 . Wird das Gerät über einen längeren Zeitraum nicht benutzt, sollten Sie es
12. Durch die Lüftungsöffnungen dürfen niemals Gegenstände oder
13. Öffnen Sie niemals das Gerät. Das Gerät darf aus Gründen der elektrischen
14. Wenn folgende Situationen auftreten ist das Gerät vom Stromnetz zu
15. Netzkabel oder Netzstecker sind beschädigt.
16. Flüssigkeit ist in das Gerät eingedrungen.
17. Das Gerät war Feuchtigkeit ausgesetzt.
18. Wenn das Gerät nicht der Bedienungsanleitung entsprechend funktioniert
oder
19. Das Gerät ist gefallen und/oder das Gehäuse ist beschädigt.
20. Wenn das Gerät deutliche Anzeichen eines Defektes aufweist.
21. VOSICHT: Explisionsgefahr bei unsachgemaben Austausch der
22. ACHTUNG: Es besteht die Explosionsgefahr, falls die Batterie auf nicht
23. Der arbeitsplatzbezogene Schalldruckpegel nach DIN 45 635 Teil 1000
beträgt
Haft ungsausschluss: Die Bedienungsanleitungen wurden entsprechend
der IEC-
704-1 erstellt. Advantech lehnt jegliche Verantwortung für die
Richtigkeit der in diesem Zusammenhang getätigten Aussagen ab.
vom Stromnetz trennen. Somit wird im Falle einer Überspannung eine
Beschädigung vermieden.
Flüssigkeiten in das Gerät gelangen. Dies könnte einen Brand bzw.
elektrischen Schlag aus- lösen.
Sicherheit nur von authorisiertem Servicepersonal geöffnet werden.
trennen und von einer qualifizierten Servicestelle zu überprüfen:
Sie mit Hilfe dieser Anleitung keine Verbesserung erzielen.
Batterie.Ersatz nur durch densellben order einem vom Hersteller
empfohlene-mahnlichen Typ. Entsorgung gebrauchter Batterien navh
Angaben des Herstellers.
fach- männische Weise gewechselt wird. Verfangen Sie die Batterie nur
gleicher oder entsprechender Type, wie vom Hersteller empfohlen.
Entsorgen Sie Batterien nach Anweisung des Herstellers.
70dB(A) oder weiger.
Safety Precaution - Static Electricity
Follow these simple precautions to protect yourself from harm and the products
from damage.
!
To avoid electrical shock, always disconnect the power from your PC
chassis before you work on it. Don't touch any components on the CPU
card or other cards while the PC is on.
!
Disconnect power before making any configuration changes. The sudden
rush of power as you connect a jumper or install a card may damage
sensitive electronic components.
Warning!
1.
Input voltage rated: 12-24 Vdc.
2.
Transport: carry the unit with both hands and handle with care.
3.
Maintenance: to properly maint ain and clean the surfaces, use
only approved products or clean with a dry applicator.
4.
CompactFlash: Turn off the power before inserting or removing
CompactFlash storage cards.
European Contact information:
Advantech Europe GmbH
Kolberger Straße 7
D-40599 Düsseldorf, Germany
Tel: 49-211-97477350
Fax: 49-211-97477300
Chapter
1
General Information This
chapter gives background
information on the TREK-674
Computing Box.
Sections include:
! Introduction
! General Specifications
! Dimensions
1.1 Introduction
The TREK-674 is a dedicated box computer for industrial, transport trucks,
buses and taxis. TREK-674 combined with variety of I/O connectors can be
connected to devices like OBD-II (see Ch3.3) or TPMS (Tire Pressure
Monitoring System) external modules via COM port. Dual display/dual audio
interfaces supporting different resolutions can deliver different applications to
different displays; eg: one application to a driver and another to a digital
signage application.
Built-in wireless communications (WWAN, WLAN, BT) enable TREK-674 to
send important driver/ location/cargo information back to the control center.
TREK-674 can also operate in extreme environments with features like a
wide working temperature range (-30 to 70 degrees). TREK-674 also uses a
special design to handle the critical issue of in power. Special power
protection (ISO7637-2/SAE J1455 Class A/ SAE J1113) and power
management software (Ignition on/off, delay on/off, low battery monitor)
prevent electrical noise and surges from impacting the system, guarding
against damage from transient power.
Rear-Side Connectors
1.2 General Specifications
Key features
z Supports WES8/WES7 and Linux
z Automotive grade working temperature range (-30° C to 70° C)
z Rich I/O including RS-232, WLAN1,WLAN2,WWAN1,WWAN2,GPS,Power in,
Smart Display, VGA, A/V in, Vehicle I/O, Generic I/O,USB*2, LAN1, LAN2
z Built-in communication modules, including GSM/GPRS/HSDPA/CDMA,
WLAN & Bluetooth
z GPS with AGPS and dead reckoning technology (speed line)
z Certifications: CE/FCC/e-mark, MIL-SD810F, ISO 7637-2, SAE J1455, SAE
J1113 regulations
z Ignition on/off delay; SW detectable/controllable for power management
1.2.1 General
!
!
!
Note! For mor e detail of function p lease refer to Chapter 4, Section
!
!
!
Dimensions
Weight
Power supply
–
Input voltage
–
Ignition on/off
4.3.2 of this manual.
Power consumption
watts. The power
running;
Front panel and back cover
(Not including the I/O ports).
Enclosure
: (W x H x D): 294X73X184mm.
: 3.5 KG
no I/O device and modules connected to the TREK-520).
:
: 12 ~ 24Vdc, support ignition cold crank
: The maximum current consumption is about 32.4
consumption is 12 watts in normal mode (with only XPE
: Ruggedized aluminum without ventilation holes.
: IP65 Sealed; NEMA4 compliant
1.2.2 Standard PC Functions
CPU
:
intel Antom Baytrail-I, E3827 (Dual Core, 1.75GHz)
System memory
Graphic:
Storage:
Serial ports
Universal serial bus (USB) port
Bluetooth:
Watchdog timer
RTC Battery
Power management
CAN bus:
Video/Audio input:
Optional modules
1.2.3 Touchscree n
Type
Light transmission
Controller
Power consumption
Durability
Software driver
1.2.4 Environment
High/low temperature:
Relative humidity
Shock
Certifications
Vibration
Integrated 2D/3D Graphic Engine
CFast 16GB (OS), SSD 64GBUMLC
Smart Display, VGA, A/V in, Vehicle I/O, Generic I/O,USB*2, LAN1, LAN2
when the system stops due to a program error. Jumper selection
Standby/Suspend modes.
: Analog Resistive
: > 10 million depressions
: 30 G peak acceleration (11 msec duration)
: 5 ~ 500 Hz SAE J1455 4.9.4.2, MIL-STD-810F 514.5
One Class2 Bluetooth V2.1 + EDR module/ BT 3.0
CAN, J1939, OBDII/ISO-15765
: RS-232 interface
:
So-Dimm DDR3L-1066/1333 2G or 4G
:
RS-232, WLAN1,WLAN2,WWAN1,WWAN2,GPS,Power in,
: 63-level timer intervals automatically generate system reset
and software enabled/disabled.
: 3.0 V @ 200 mA lithium battery.
: Supports power saving modes including Normal
8-ch Video input
: 12 channels GPS, quad-band GSM/GPRS, WLAN card
: 80%
: Supports Windows WES7/WES8, Linux
: 10 ~ 95% @ 40° C (non-condensing)
: CE, FCC, CCC, Emark, CB.
: Supports up to three USB2.0*1 & USB3.0*1
: <5.5 V@ 20 mA
-30 ~ 70° C
1.4 Dimensions
igure 1.1 TREK-674 di
Loading...