WISE-4210
Industrial LPWAN SUB-G Wireless I/O Module
Startup Manual
Overview |
|
Battery |
|
|
|
Thank you for purchasing the WISE-4210 module. This quick start guide is intended to help you deploy your new module. The guide contains basic information on the power and application wiring.
Should you require additional instructions, please refer to the user manual.
Input Power Requirements
The WISE-4210 is designed for a standard industrial unregulated 24 VDC power supply. For some applications, it can also accept +10 to +50 VDC power input with 200 mV peak-to-peak power ripple. The immediate ripple voltage
should be between +10 and +50 VDC. Batteries may also be used as an alternative power source.
Packaging List
•1 x WISE-4210 module
•1 x Mounting bracket
•1 x Quick start manual
•1 x China RoHS declaration (UA series only)
•1 x Antenna (UA series only)*
*For NA series, antennas should be ordered respectively per required frequency range
** WISE-S200 I/O module should be ordered respectively
Power Supply Wiring
For more information on this and other Advantech products, please visit our website at:
http://www.advantech.com
For technical support and service: https://www.advantech.com/support/
This startup manual is for WISE-4210. |
|
Part No. 2003421052 |
Edition 3 |
Printed in Taiwan |
October 2019 |
Open the rubber cover on the side of WISE-4210 nodes, there is a battery switch to turn on or turn off the battery power supply.
The module accepts 3 x AA, 3.6 V lithium battery. The batteries should be installed facing the same direction.
WISE-4210 Startup Manual 1
Application Wiring
WISE-S214 (4AI/4DI) |
|
WISE-S251 (6DI/1RS-485) |
Digital InputDry Contact |
|
Digital Input – Dry Contact |
Analog Input |
RS-485 Port |
WISE-S250 (6DI/2DO/1RS-485)
Digital Input-Dry Contact
Digital Output
RS-485 Port
Membrane Button
|
Mode |
Light Press |
Long Press |
|
|
(0.5 Sec) |
(2 Secs) |
||
|
|
|||
|
|
|
|
|
|
|
LED turns |
|
|
Normal |
Power Sav- |
on→Gets |
Leave normal |
|
battery |
||||
ing Mode |
mode |
|||
Mode |
level→LED |
|||
|
|
|||
|
|
turns off* |
|
|
|
|
|
|
|
|
Non-power |
Get battery |
Leave normal |
|
|
level→LED |
|||
|
Saving Mode |
mode |
||
|
|
turns off* |
|
S i t e - |
Light Press |
Long Press |
|
(0.5 Sec) |
(2 Secs) |
||
Survey |
|||
|
|
||
Mode |
Tx site survey packet |
Leave site survey mode |
|
|
|||
|
|
|
|
Status |
Light Press |
Long Press |
|
|
(0.5 Sec) |
(2 Secs) |
||
|
|
|||
|
|
|
|
|
|
Rx Status |
Read battery |
Leave OTA |
|
|
level |
mode |
||
|
|
|||
|
|
|
|
|
OTA |
Tx Status |
Tx |
Tx Firmware |
|
Mode |
(by USB port) |
Configuration |
||
|
||||
|
Low Battery |
NA |
Leave OTA |
|
|
mode |
|||
|
|
|
||
|
|
|
|
|
|
Update FW |
Reset OTA |
NA |
|
|
fail |
mode |
||
|
|
|||
|
|
|
|
*LED indicators will go off automatically 15 secs later when using battery power
2 WISE-4210 Startup Manual