Advantech UTX-3117FSP-S6A2N, UTX-3117FS-S6A1N, UTX-3117FS-S6A2N, UTX-3117C-S6A2N, UTX-3117C-S6A2E User Manual

The information contained in this document has been carefully researched and is, to the best of our
knowledge, accurate. However, we assume no liability for any product failures or damages, immediate or
consequential, resulting from the use of the information provided herein. Our products are not intended for
use in systems in which failures of product could result in personal injury. All trademarks mentioned herein
are property of their respective owners. All specifications are subject to change without notice.

Manual

ADVANTECH

UTX-3117

Embedded BOX PC with Intel® Apollo Lake Prozessor

User Manual

UTX-3117

Copyright

The documentation and the software included with this product are copyrighted 2018
by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right
to make improvements in the products described in this manual at any time without
notice. No part of this manual may be reproduced, copied, translated or transmitted
in any form or by any means without the prior written permission of Advantech Co.,
Ltd. Information provided in this manual is intended to be accurate and reliable. How ­ever, Advantech Co., Ltd. assu mes no responsibility for its use, nor for any infringe­ments of the rights of third parties, which may result from its use.

Acknowledgements

Intel® and Pentium® are trademarks of Intel Corporation.

Microsoft® Windows® and MS-DOS® are registered trademarks of Microsoft Corp.

All other product names or trademarks are properties of their respective owners.

Product Warranty (2 years)

Advantech warrants to you, the original purchaser, that each of its products will be
free from defects in materials and workmanship for t wo year s from the date of pur­chase .

This warranty does not apply to any products which have been repaired or altered by
persons other tha n repair pe rson nel authorized by Adva ntech , or whi ch have bee n
subject to mi sus e, abuse , accident or improper installation. Ad vant ech ass umes no
liability under the terms of this warranty as a consequence of such events.

Because of Advantech’s high quality-control standards and rigorous testing, most of
our customers never need to use our repair service. If an Advantech product is defec­tive, it will be repaired or replaced at no charge during the warranty period. For outof­warranty repairs, you will be billed according to the cost of replacement materials,
service time and freight. Please consult your dealer for more details.

If you think you have a defective product, follow these steps:

1. Collect all the information about the problem encountered. (For example, CPU

speed, Advant ech products us ed, other hardware and software used, etc.) Note
anyt hing abnormal and list any onscr een messages you get wh en the probl em
occurs.

2. Call your dealer and describe the problem. Please ha ve your manual, product,

and any helpful information readily available.

3. If your product is diagnosed as defective, obtain an RMA (return merchandise

authorization) number from your dealer. This allows us to process your return
more quickly.

4. Carefully pack the defective product, a fully-completed Repair and Replacement

Order Card and a photocopy proof of purchase date (such as your sales receipt)
in a shippable container. A product returned without proof of the purchase date
is not eligible for warranty service.

5. Write the RMA number visibly on the outside of the package and ship it prepaid

to your dealer.

Part No. Edition 1

Printed in Taiwan March 2018

UTX-3117 User Manual ii

Declaration of Conformity

FCC Class B

Note: This equipment has been tested and found to comply with the limits for a Class
B digital device, pur suant to part 15 of the F C C Rules. These limits are desi gned to
provide reas ona ble protectio n aga inst harmful interference in a residential installa­tion. T his equip ment generates, uses and can radiate radio frequenc y energy and, if
not installed and used in accordance with the instructions, ma y cause harmful inter­ference to radio communicati ons . Ho w ever, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interfer­ence to radio or television reception, which can be determined by turning the equip­me nt off and on, the user is encour a ged to try to correct t he interference by one or
more of the following measures:

 Reori ent or relocate th e receiving antenna.
  Increase the s eparatio n between the equi pment and recei ver.
Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected .

 Consult the dealer or an experienced radio/TV technician for help.

Warning! Any changes or modifications made to the equipment which are not

expressly approved by the relevant standards authority could void your
authority to operate the equipment.

Caution! Danger of explosion if battery is incorrectly replaced. Replace only with

the same or equivalent type recommended by the manufacturer. Dis­pose of used batteries according to the manufacturer’s instructions.

This device co mplies with Part 15 of the FCC Rules. Operation is subject to the fol­lowing two conditions : (1) Thi s device may not cause harmful interference, and (2)
this devi ce must acc ept any interference received, includi ng int erference t hat may
cause undesired operation.

iii UTX-3117 User Manual

Technical Support and Assistance

1. Visit the Advantech website at http://support.advantech.com where you can find

the latest information about the product.

2. Contact your distributor, sales representative, or Advantech's customer service

center for technical sup port if you need additional assistance. Please have the
following information ready before you call:

– Product name an d serial number
– Description of your peripheral attachments
– Description of your software (operating system, version, application software,

etc.)

– A complete description of the problem
– T he exact wordin g of any error messages

Warning!

1. Input voltage rated 12~24 VDC, 3 ~ 5 A (DC Mode).\

2. Packing: please carry the unit with both hands, handle with care.

3. Maintenance: to properly maintain and clean the surfaces, use only

approved products or clean with a dry applicator.

Safety Instructions

1. Read these safety instructions carefully.

2. Keep this User Manual for later reference.

3. Disconnect this equipment from any AC outlet before cleaning. Use a damp

cloth. Do not use liquid or spray detergents for cleaning.

4. For plug-in equipment, the power outlet socket must be located near the equip-

ment and must be e asily accessible .

5. Keep this equipment away from humidity.

6. Put this equipment on a reliable surface during installation. Dropping it or letting

it fall may ca use damage.

7. Th e openings on the enclosure are for air convection. Protect the e quipment

from overheating. DO NOT COVER THE OPENINGS.

8. Make sure the voltage of the power source is correct before connecting the

equipment to the p ower outlet.

9. Position the po wer cord so that people cannot step on it. Do not place anything

over the power cord.

10. All cautions and warnings on the equipment should be noted.

11. If the equipment is not used for a long time, disconnect it from the power source

to avoid damage by transient overvoltage.

12. Never pour any liquid into an opening. This may cause fire or electrical shock.

13. Never open the eq uipment . For safety reasons, the equi pment should be

opened only by qualified service personnel.

14. If one of the following situations arises, get the equipment checked by service

perso nnel:
a. The power cord or plug is d amage d.
b. Liquid ha s penetrated into the equipment.
c. The equipment h as been expos ed to moisture.
d. The equipment does not work well, or you cannot get it to work according to

the user's man ual.

e. The equipme nt h as b een dro pped and da mage d .

UTX-3117 User Manual iv

f. The equipment has obvious signs of breakage.

15. DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT WHERE THE

STORAGE TEMPERATURE MAY GO BELOW -20° C (-4° F) OR ABOVE 60° C
(140° F). THIS COULD DAMAGE THE EQUIPMENT. THE EQUIPMENT
SHOULD BE IN A CONTROLLED ENVIRONMENT.

16. If your computer is losing dramatic time or the BIOS configuration reset to

default, the battery has no power.

Caution!

1. Do not replace power adaptor yourself. Please contact a qualified

technician or your retail.

2. The computer is provided with a battery-powered real-time clock

circuit. There is a danger of explosion if battery is incorrectly
replaced. Replace only with same or equivalent type recom­mended by the manufacture. Discard used batteries according to
the manufacturer’s instructions.

17. CLASSIFICATION:

– Supply by Class I

adapter – No applied part

– Continuous Operation
– Not AP or AP G category

18. Follow the national requirement to dispose unit.

19. Maintenance: to properly maintain a nd clean the surfaces, use only the

approved products or clean with a dry cloth.

20. Contact information:

No.1, Alley 20, Lane 26, Rueiguang Road Neihu District, Taipei, Taiwan 114,
R.O.C
TEL: [phone]

Industry Canada Statement

This device complies with RSS-210 of the Industry Canada Rules. Operation is sub­ject to the following two conditions: (1) This device ma y not cause harmful interfer­enc e, and (2 ) this devi ce must acce pt any inte r feren ce rec eive d, inc l uding
interference that may cause undesired operati on.

French User Manual Statements for RSS Warnings

FCC/Industry Canada Two-Part Statement:

English Version

This devi ce complies wi th F C C Part 15 and Indus try Can a d a license exe mpt R S S
standard(s). Operation is subject to the following two conditions: (1) this device may
not cause i nterference, and (2) this devi ce must accept a n y i nterference , incl udi ng
interference that ma y cause unde sired operation of the device.

Version française

Ce t appareil e st c onforme à F C C P artie1 5 d’Industrie Cana da RS S standard
exempts de licence (s). Son utilisation es t sou mise à Les deux conditions suivantes:
(1) cet appareil ne peut pas provoquer d’interférences et (2) cet appareil doit
accepter Toute interférence, y compris les interférences qui peuvent causer un mau­vais fonctionnement du dispositif.

v UTX-3117 User Manual

Version française

"Les cha ngements ou modifications non expressé ment approuvés par la partie
responsable de la conformité pourraient annuler l'autorité de l'utilisateur à utiliser cet
équipement."

European Union Declaration of Conformity Statement

We, Advantech , declare under our sole responsibility that th e product, model, is in
conformity with all applicable essential requirements Necessary for CE marking, fol­lowing the provisions of the European Council Directives 2004/108/EC (EMC Direc­tive), 2006/95/EC (Low Voltage Directive), 1999/5/EC (Radio and
Telecommunications Terminal Equipment Directive) and 2011/65/EU (ROHS Direc­tive).

The product is properly CE marked demonstrating this conformity and is for distribu­tion within all member states of the EU with no restrictions.

This product follows the provisions of the European Directives 2004/108/EC, 2006/
95/EC, 1999/5/EC and 2011/65/EU.

Čeština Tento výrobe k odpovídá požadavkům e vropských směrnic 2004/108/E C,
2006/95/EC, 1999/5/EC a 2011/65/EU.

Dansk Dette produkt er i overensstemmelse med det europæiske direktiv 2004/108/
EC, 1999/5/EC, 2006/95/EC & 2011/65/EU.

Du tch Dit product is in navolging va n de bepalingen van Eur opees Directief 2004/
108/EC, 1999/5/EC, 2006/95/EC & 2011/65/EU.

Eesti Antud toode vastab Euroopa direktiivides 2004/108/EC, ja 2006/95/EC ja 1999/
5/EC ja 2011/65/EU kehtestatud nõuetele.

Suomi Tämä tuote noudattaa EU-direktiivin 2004/108/EC, 1999/5/EC, 2006/95/EC &
2011/65/EU määräyksiä.

Français Ce produit est c onforme aux exigences de la Directive Européenne 2004/
108/EC, 1999/5/EC, 2006/95/EC & 2011/65/EU.

Deutsch Dieses Produkt entspricht den Bestimmungen der Europäischen Richtlinie
2004/108/EC, 1999/5/EC 2006/95/EC & 2011/65/EU.

Εηνά Τ παό πό αυί τ ατά τ Ευπαώ Ογώ 2004/
108/EC, 1999/5/EC, 2006/95/EC α 2011/65/EU.

Magyar E termék megfelel a 2004/108/EC, 1999/5/EC, 2006/95/EC és 2011/65/EU
Európai Irányelv előírásainak.

Icelandic Þessi vara stenst re glugerð Evrópska Efnahags Bandalagsins núme r
2004/108/EC, 2006/95/EC, & 2011/65/EU.

UTX-3117 User Manual vi

Italiano Questo prodotto è conforme alla Direttiva Europea 200 4/108/EC, 199 9/5/
EC, 2006/95/EC & 2011/65/EU.

Latviešu Šis produkts atbilst Eiropas Direktīvu 2004/108/EC, 1999/5/EC, 2 006/95/
EC un 2011/65/EU noteikumiem.

Lietuvi ų Šis produktas atitinka Europos direktyvų 2004/108/EC, 1999/5/EC, 2006/
95/EC, ir 2011/65/EU nuostatas.

Malti Dan il-prodott hu konformi mal-provvedimenti tad-Direttivi Ewropej 2004/108/
EC, 1999/5/EC, 2006/95/EC u 2011/65/EU.

Norsk Det te produkte t er i hen hold til best emme lsene i det eu rope iske direktivet
2004/108/EC, 1999/5/EC, 2006/95/EC & 2011/65/EU.

Polski Niniejszy produkt jest zgodny z postanowieniami Dyrektyw Unii Europejskiej
2004/108/EC, 1999/5/EC, 2006/95/EC i 2011/65/EU.

Po rtug uese Este pr oduto cumpre com as normas da Diretiva Européia 2004/108/
EC, 1999/5/EC, 2006/95/EC & 2011/65/EU.

Español Este producto c umple con las normas del Directivo Europeo 2004/108/EC,
1999/5/EC, 2006/95/EC & 2011/65/EU.

Slovensky Tento produkt je v súlade s ustanoveniami európskych direktív 2004/108/
EC, 1999/5/EC, 2006/95/EC a 2011/65/EU.

Slovenščina Izdelek je skladen z določbami evropskih direktiv 2004/108/EC, 1999/
5/EC, 2006/95/EC in 2011/65/EU.

Sve n ska D enna produkt har tillverkats i enlighet med EG-direktiv 2004/108/ EC,
1999/5/EC 2006/95/EC & 2011/65/EU.

Türkçe Bu ürün, Avrupa Birliği’nin 2004/108/EC, 1999/5/EC, 2006/95/EC ve 2011/
65/EU yönergelerine uyar.

This symbol on the product indicates co mpliance with Directive 2002/96/EC

(WEEE). Do not dispose of product in unsorted municiple waste.

Please recycle t his p rod uct in a responsible ma n ner. Refer to local envir onmental
regulati ons fo r pr oper rec ycli ng; do not disp ose of p roduct in u nsor ted municipa l
wa ste.

vii UTX-3117 User Manual

Packing List

Before installation, please ensure the following items ha ve been shipped:

 1 x UTX-3117 unit
 1 x DC 12 V 36 W power adaptor
 1 x China R o HS
 1 x Warranty card
  1 x C hine se user man u al

Ordering Information

P/N CPU SSD Mem ory WiFi 3G/LTE Other RF An ten na OS

UTX-3117FS-S6A1N

PENTIUM N4200, 4C 2M

1.1 GHz

32GB 4 GB X 1 NA NA NA

4

NA

UTX-3117FS-S6A2N

CELERON N3350 2C 2M

1.1 GHz

32GB 4 GB X 1 NA NA NA

4

NA

UTX-3117 FS-S6A2E

Atom X5-E3940 4C 2M

1.6 GHz

32GB 4 GB X 1 NA NA NA

4

NA

UTX-3117FSW­S6A1N

PENTIUM N4200, 4C 2M

1.1 GHz

32GB 4 GB X 1 NA NA NA

4

WIN 10

UTX-3117 FSP-S6A2N

CELERON N3350 2C 2M

1.1 GHz

32GB 4 GB X 1 NA NA NA

4

Pulsa r 8

UTX-3117C-S6A2N

CELERON N3350 2C 2M

1.1 GHz

NA NA

NA NA NA

NA NA

UTX-3117C-S6A2E

Atom X5-E3940 4C 2M

1.6 GHz

NA NA

NA NA NA

NA NA

UTX-3117C-S6A1N

PENTIUM N4200, 4C 2M

1.1 GHz

NA NA

NA NA NA

NA NA

UTX-3117SA4-S6A1N

PENTIUM N4200, 4C 2M

1.1 GHz

NA 4GB X 1 NA NA NA

4

NA

UTX-3117SA4-S6A2N

CELERON N3350 2C 2M

1.1 GHz

NA 4GB X 1 NA NA NA

4

NA

UTX-3117 SA4-S6A2E

Atom X5-E3940 4C 2M

1.6 GHz

NA 4GB X 1 NA NA NA

4

NA

UTX-3117 User Manual viii

Compatibility List

Power Cord

Part Number Description

17 000 01524

Power Cable 3-pin 180cm, U SA type
(For power adapter 1757004096-01)

17 02031 83C

Po wer Cable 3-pin 180 cm, Europe type
(For power adapter 1757004096-01)

170203 180A

Power Cable 3-pin 180cm, UK type
(For po wer adapter 1757004096-01)

17 000 08921

Power Cable 3-pin 18 3cm, P SE Mark type
(For power adapter 1757004096-01)

Optional Items

ix UTX-3117 User Manual

UTX-3117 User Manual x

Contents

Chapter 1 Introduction..........................................1

1.1 Overview...................................................................................................2

1.2 Syste m Configuration........................................ ........................................3

1.3 Gener al Specifications..............................................................................4

1.3.1 Standard PC Functions.................................................................4

1.3.2 Po we r Environmental................................. ...................................4

1.4 Mecha nical Specifications.........................................................................4

1.4.1 Mechanical Specifications (Terminal)...........................................4

1.5 Environmental Specifications....................................................................5

Chapter 2 Jumper and Connector List ................7

2.1 Conne ctors & Jumpers..............................................................................8

Figure 2.1 T op View.....................................................................8

Figure 2.2 Bot tom Vie w ...............................................................9

Table 2 .1 : RS485/R S422selection pin he ader (J485/422)........10

Table 2.2: AT/ATX Mode Selection (PSON1)............................10

2.2 Connectors............................................................... ...............................10

2.2.1 CP U-S ys tem on chip (SOC1 ) ......................................................10

2.2.2 B IOS Flash(SPI1) .......................................................................11

2.2.3 DDR3L SO-DIMM Socket (DIMMA1)..........................................11

2.2.4 DC i nput Connector(DCIN1).......................................................11

2.2.5 MINIP CIE Connector (MINI-PCIE1)............................................12

2.2.6 S IM Card Socket (SIM1).............................................................13

2.2.7 Lo w Pin Count Header (LPC1) ...................................................13

2.2.8 MINIPCIE and mSATA Connector (MINI-PCIE2) .......................14

2.2.9 SPI Programming Pin H ead er (SPI_CN1)..................................15

2.2.10 COM Port (COM1)......................................................................16

2.2.11 Ge neral P ur pose I/ O Pin Header (GPIO1)..................................16

2.2.12 HD Analog Audio Interface (AUDIO1).........................................17

2.2.13 COM Port (COM2)......................................................................17

2.2.14 N ext Generatio n Form Factor (M.2_1)........................................18

2.2.15 S ATA Signal Connec tor (SATA1)...............................................19

2.2.16 USB 3.0 Connector(USB1).........................................................19

2.2.17 USB 3.0 Connector(USB2).........................................................19

2.2.18 SAT A P ower Connector (SATA_PWR1).....................................20

2.2.19 R J45 Connector(LAN1)...................... .........................................20

2.2.20 R J45 Connector(LAN1)...............................................................20

2.2.21 High Definition Multimedia Interface(HDMI1)..............................21

2.2.22 Di sp layPort (DP1).......................................................................21

2.2.23 DDR3 L SO-DIMM Socket (DIMMB1)..........................................22

2.2.24 S ATA LED(D10)..........................................................................22

2.2.25 P ower Bu tto n(PWRBTN 1) ..........................................................22

Chapter 3 Peripheral Installation .......................23

3.1 HDD Installation......................................................................................24

3.2 Mini P CIe Module Installation..................................................................26

Chapter 4 BIOS Setup .........................................29

4.1 Introd uction .............................................................................................30

4.2 Entering Set up ........................................................................................31

xi UTX-3117 User Manual

4.2.1 Mai n Menu.................................................................................. 31

4.2.2 Advanc ed BIO S Features........................................................... 32

4.2.3 Chipset........................................................................................ 52

4.2.4 Security Boo t .............................................................................. 59

4.2.5 B oot ............................................................................................ 61

4.2.6 Save & Exit................................................................................. 62

UTX-3117 User Manual xii

Chapter 1

1

This Chapter briefly introduces
the UTX-3117 product.

Introduction

1.1

Overview

Th e Advantech U TX-3 117 system is fanless & ext ended=temp embedded box. The
solution uses the latest Intel® Atom® E3900, Celeron® N3350, and Pentium®
N4200 series processor technology to provide a real-time IoT computing, power-effi­cient, plug & play gateway which is ideal for smart city street lighting, smart metering,
smart parking, smart agriculture, HVAC, healthcare, industrial automation and more.
UTX-3117 is compatible with Microsoft Windows 10 IoT Enterprise, Yocto Linux, and
Wind Ri ver Pulsar OS. Furthermore, UTX-3117 has Advantech intelligent software
WISE -PaaS integrated and is certificated with AWS Greengrass IoT solution to offer
a total solution for bridging connectivity from edge sensors to the cloud.

Benefits:

 Ultra Thin ITX embedded system with CE/FCC certification
Fanless, wide-temperature operation with high performance and flexibility
 Design in 3 extension slot for RF module, mSATA, or other I/O dongle.
Support 12V ~ 24V wide voltage DC input.
 One-Stop Integrated Solution: Integrated ultra compac t motherboard, chas-

sis,peripherals a nd software

 Di mensions: 152 x 128 x 37.1 mm

UTX-3117 User Manual 2

1.2

System Configuration

The following diagram is a block drawing of the UTX-3117.

HDMI

DP1.2

1 SATA 3.0

DDI

DDI

600M Bs

PC IE x1

DD R3L Non -ECC
1333 /1600/ 1867
MHz, up to 8G

GbE 1:
I211AT

2 USB3.0

ALC892,

Line out /MIC in

US B3.0

HD AUDIO

Intel

Apollo Lake

N4200/E39xx SoC

TDP:5.5~13W

PC IE x1

US B2.0

PC IE x1

US B2.0

SATA 3.0

GbE 2:

RTL8111G

F/S mini PCI E,
w/SI M ho ld
(3G/LTE module)

H/S mini PCIE,
Colay mS ATA

M.2 E key

(WIFI / GPS/ BT
/Zig bee mo dule)

PC IE x1
USB2 .0

Pow er: DCI N12~24 V

LP C Bus

TPM

Infin eon
SLB 9660

Sup er I/O

NCT5523D

1 RS-232

1 RS-4 22/ 485

8bit GPIO

WDT

H/W moitor

Button I/O arrangement:

USB 3.0

LAN

HDMI

DP HDD LED

Power Bu on

WSN ANT Audio Jack

RS-422/485 RS-232 12-24V DC IN

3 UTX-3117 User Manual

Chapter

1

Introduction

1.3

General Specifications

1.3.1

Standard PC Functions

CPU: Intel® Atom™ E3900 series, Pentium N4200, Celeron N3350 SoC.

 BIOS: AMI EFI 16bit
Memory: DDR3L SODIMM 1333/1866 MHz up to 8GB
 Audio: HD audio codec ALC892
 LAN: PCI-E gIGABIT Ethernet controllers x2

LAN1: Intel i210AT; LAN2: RTL8111G

 Universal serial bus (USB) port: 2 USB3.0
Mini PCI-E bus expansion slot: 1 F/S miniPCIE support 3G/LTE card; 1 H/S

miniPCIE support mSATA/WIFI card, 1 M.2 E-key support WiFI card.

 Storage housing: 1 2.5" slim SSD
 Audio output: Combo Audio Jack
Video output: 1 HDMI, 1 Display port

1.3.2

Power Environmental

Power adaptor: AC/DC

– Input voltage: 100 Vac ~ 240 Vac @ 50 - 60 Hz,1.5

A

– Output voltage: 12 V @ 3 A~24V @ 3A

1.4 Mechanical Specifications

1.4.1

Mechanical Specifications (Terminal)

System Dimensions: 152 X 128 X 37.1 mm (5.98" X 5.2" X 1.46")

Carton Dimensions: 255 (L) X 235 (W) X 160 (H) mm
 Gross Weight: 2.0 kg
 Net Weight: 1.8 kg

UTX-3117 User Manual 4

1.5

Environmental Specifications

Temperature & Humidity

Operating Temperature: -20 ~ 60 ° C (with RF module)
Storage Temperature: -40 ~ 60° C
 Relative Humidity: 40 ~ 95% RH (Non-condensed)

Safety

 CE / UL/CB/CCC/BSMI

EMI

 FCC class B approved for USA, Canada, and E U

Vibration:

With SSD: 3Grms, 60068-2-64, random, 5 ~ 500 Hz, 1 hr/axis

5 UTX-3117 User Manual

Chapter

1

Introduction

UTX-3117 User Manual 6

Chapter 2

2

Connector List

Jumper and

2.1

Connectors & Jumpers

Figure 2.1 Top View

UTX-3117 User Manual 8

Figure 2.2 Bottom View

Connector and Header List:

(1) CPU-System on chip(SOC1)
(2) BIOS Flash(SPI1)

(3) DDR3LSO-DIMM Socket (DIMMA1)

(4) DC input Connector (DCIN1)
(5) MINIPCIE Connector (MINI-PCIE1)

(6) SIM Card Socket (SIM1)
(7) Low Pin Count Header (LPC1)
(8) MINIPCIE and mSATA Connector (MINI-PCIE2)
(9) SPI Programming Pin Header(SPI_CN1)

(10) COM Port(COM1)
(11) General Purpose I/O Pin Header (GPIO1)

(12) HDAnalog Audio Interface(AUDIO1)
(13) COM Port(COM2)
(14) Next Generation Form Factor (M.2_1)

(15) SATA Signal Connector (SATA1)
(16) USB 3.0 Connector(USB1)
(17) SATA Power Connector (SATA_PWR1)

(18) USB 3.0 Connector(USB2)
(19) RJ45 Connector(LAN2)
(20) RJ45 Connector(LAN1)

(21) High Definition Multimedia Interface(HDMI1)
(22) DisplayPort(DP1)
(23) DDR3LSO-DIMM Socket (DIMMB1)

9 UTX-3117 User Manual

Chapter

2

Jumper

and

Connector

List

(24) SATA LED(D10)
(25) Power Button(PWRBTN1)

Jumper List:

(1) RS485/RS 422selection pin header (J485/422)

Table 2.1: RS485/RS422selection pin header (J485/422)

Function Setting

RS485 (Default)

1 2 3

1 2 3

1 and 2

RS 2 32

2 and 3

Table 2.2: AT/ATX Mode Selection (PSON1)

Function Setting

AT Mode

1 2 3

1 2 3

1 and 2

ATX Mode (Default)

2 and 3

2.2

Connectors

2.2.1

CPU-System on chip(SOC1)

UTX-3117 User Manual 10

2.2.2

BIOS Flash(SPI1)

Pin Signal Pin Signal

1 SPI _Z_ CS0 6 SPI_Z_CLK
2 SPI_Z_MISO 7 SPI_Z_IO3
3 SPI_Z_IO2 8 +V1.8SB_SPI
4 GND
5 SPI_Z_MOSI

2.2.3

DDR3L SO-DIMM Socket (DIMMA1)

2.2.4

DC input Connector(DCIN1)

Pin Signal

1 Power input
2 GND
3 GND

11 UTX-3117 User Manual

Chapter

2

Jumper

and

Connector

List

2.2.5

MINIPCIE Connector (MINI-PCIE1)

MINIPCIE:

Pin Signal Pin Signal

1 WAKE# 2 +3.3Vaux
3 Rese r ved 4 GND
5 Rese r ved 6 +1.5V
7 Rese r ved 8 SIM_VCC1
9 GND 10 SIM_IO1
11 Res erved 12 SIM_CLK1
13 Re served 14 SIM_RST1
15 GND 16 SIM_SPU1
17 Re served 18 GND
19 Re s erved 20 DISABLE#
21 GND 22 RE SET#
23 Re served 24 +3.3Vaux
25 Re served 26 GND
27 GND 28 +1.5V
29 GND 30 Reserved
31 Re served 32 Res erved
33 MINI-PCIE1 _RESET# 34 GND
35 GND 36 USB_D­37 GND 38 USB_D+
39 +3.3Vaux 40 GND
41 +3.3Vaux 42 Reserved
43 Re served 44 Res erved
45 Re served 46 Res erved
47 Re served 48 +1.5V
49 Re served 50 GND
51 Re served 52 +3.3Vaux

UTX-3117 User Manual 12

2.2.6

SIM Card Socket (SIM1)

Pin Signal Pin Signal

C1 SIM_VCC1 H1 GND
C2 SIM_RST1 H2 GND
C3 SIM_CLK1 H3 GND
C5 GND H4 GND
C6 SIM_SPU1

2.2.7

Low Pin Count Header (LPC1)

Pin Signal Pin Signal

1 SOC_LPC_AD1 2 CLKOUT_25M_LPC
3 SOC_LPC_AD0 4 PM_PLTRST#
5 +V3.3 6 SOC_LPC_FRAME#
7 GND 8 SOC_LPC_AD3
9 X 10 SOC_LPC_AD2

13 UTX-3117 User Manual

Chapter

2

Jumper

and

Connector

List

2.2.8

MINIPCIE and mSATA Connector (MINI-PCIE2)

MINIPCIE:

Pin Signal Pin Signal

1 WAKE# 2 +3.3Vaux
3 Re s erv ed 4 GND
5 Re s erv ed 6 +1.5V
7 CLKREQ# 8 Re ser ved
9 GND 10 Re ser ved
11 REFCLK- 12 R eserved
13 REFCLK+ 14 R ese rved
15 GND 16 Reserve d
17 Rese rve d 18 GND
19 Reser ved 20 DISABLE#
21 DETECT# 22 R ESET #
23 PCIE_RX+ 24 +3.3Vaux
25 PCIE_RX- 26 GND
27 GND 28 +1.5V
29 GND 30 SMB_CLK
31 PCIE_TX- 32 SMB_DATA
33 PCIE_TX+ 34 GND
35 GND 36 USB_D­37 GND 38 USB_D+
39 +3.3Vaux 40 GND
41 +3.3Vaux 42 Reserve d
43 V1.2_DETECT# 44 LED_WLAN#
45 Rese rve d 46 Reserved
47 Rese rve d 48 +1.5V
49 Rese rve d 50 GND
51 MSATA_DETECT# 52 +3.3Vaux

mSATA:

Pin Signal Pin Signal

1 Res erve d 2 +3.3V
3 Res erve d 4 GND
5 Res erve d 6 +1.5V
7 Res erve d 8 Re ser ved
9 GND 10 R eserved

UTX-3117 User Manual 14

11 R eser ved 12 Res erv ed
13 Re served 14 Res erved
15 GND 16 Rese rve d
17 Re served 18 GND
19 Re served 20 Res erved
21 DETECT# 22 Reserved
23 RX+ 24 +3.3V
25 RX- 26 GND
27 GND 28 +1.5V
29 GND 30 SMB_CLK
31 TX- 32 SMB_DATA
33 TX+ 34 GND
35 GND 36 Rese rve d
37 GND 38 Rese rve d
39 +3.3V 40 GND
41 +3.3V 42 Reserved
43 Re served 44 Res erved
45 Re served 46 Res erved
47 Re served 48 +1.5V
49 Re served 50 GND
51 MSATA_DETECT# 52 +3.3V

2.2.9

SPI Programming Pin Header (SPI_CN1)

Pin Signal Pin Signal

1 CS# 2 +3.3V
3 MISO 4 X
5 X 6 SCK
7 GND 8 MOSI

15 UTX-3117 User Manual

Chapter

2

Jumper

and

Connector

List

2.2.10

COM Port (COM1)

Pin Signal Pin Signal

1 DCD# 6 DSR#
2 RXD 7 RTS#
3 TXD 8 CTS#
4 DTR# 9 RI#
5 GND

2.2.11

General Purpose I/O Pin Header (GPIO1)

Pin Signal Pin Signal

1 GPIO0 2 GPIO4
3 GPIO1 4 GPIO5
5 GPIO2 6 GPIO6
7 GPIO3 8 GPIO7
9 +3.3V 10 GND

UTX-3117 User Manual 16

2.2.12

HD Analog Audio Interface (AUDIO1)

Pin Signal Pin Signal

1 CONN_FRONT_L 6 GND_A
2 CONN_FRONT_R MS1 GND_A
3 GND_A MS2 GND_A
4 CONN_MIC1_L H1 x
5 FRONT_SENSE_A H2 x

2.2.13

COM Port (COM2)

Pin Signal

1 COM2_422_485_TX­2 COM2_422_485_TX+
3 GND
4 COM2_422_RX­5 COM2_422_RX+

17 UTX-3117 User Manual

Chapter

2

Jumper

and

Connector

List

2.2.14

Next Generation Form Factor (M.2_1)

Pin Signal Pin Signal

1 GND 43 PCIE_RX3­2 +V3.3SB_M.2 44 x
3 USB_D4+ 45 GND
4 +V3.3SB_M.2 46 x
5 USB_D4- 47 CK100M_NGFF+
6 x 48 x
7 GND 49 CK100M_NGFF­8 NGFF_I2S3_Z_BCLK 50 NGFF_PMU_SUSCLK
9 SDIO_WIFI_CLK 51 GND
10 NGFF_I2S3_Z_SYNC 52 NGFF_PLTRST#
11 SDIO_WIFI_CMD 53 PCIE_REQ2_ NG FF#
12 NGFF_I2S3_Z_SDI 54 NGFF_BT_DISABLE#
13 SDIO_WIFI_D0 55 PCIE_NGFF_WAKE2#
14 NGFF_I2S3_Z_S DO 56 NGFF_WIFI_DISABLE#
15 SDIO_WIFI_D1 57 GND
16 x 58 x
17 SDIO_WIFI_D2 59 x
18 GND 60 x
19 SDIO_WIFI_D3 61 x
20 NGFF_CONN_UART_WAKE# 62 x
21 SDIO_WIFI_WAKE# 63 GND
22 NGFF_UART0_Z_RXD 64 x
23 SDIO_WIFI_RST 65 x
32 NGFF_UART0_Z_TXD 66 x
33 GND 67 x
34 NGFF_UART0_Z_CTS# 68 x
35 NGFF_PCIE_TX3+ 69 GND
36 NGFF_UART0_Z_RTS# 70 x
37 NGFF_PCIE_TX3- 71 x
38 x 72 +V3.3SB_M.2
39 GND 73 x
40 x 74 +V3.3SB_M.2
41 PCIE_RX3+ 75 GND
42 x

UTX-3117 User Manual 18

2.2.15

SATA Signal Connector (SATA1)

Pin Signal Pin Signal

1 GND 6 SATA0_Z_RX+
2 SATA0_Z_TX+ 7 GND
3 SATA0_Z_TX- 8 x
4 GND 9 x
5 SATA0_Z_RX- 6 SATA0_Z_RX+

2.2.16

USB 3.0 Connector(USB1)

2.2.17

USB 3.0 Connector(USB2)

Pin Signal Pin Signal

1 +USBV1 7 GND
2 USB_D0- 8 USB3X0_Z_TX­3 USB_D0+ 9 USB3X0_Z_TX+
4 GND H1 GND_F1
5 USB3X0_Z_RX- H2 GND_F1
6 USB3X0_Z_RX+ x

19 UTX-3117 User Manual

Chapter

2

Jumper

and

Connector

List

2.2.18

SATA Power Connector (SATA_PWR1)

Pin Signal Pin Signal

1 +V5 3 GND
2 GND 4 x

2.2.19

RJ45 Connector(LAN1)

2.2.20

RJ45 Connector(LAN1)

RJ45

Pin Signal Pin Signal

R1 LAN2_TCT R10 LAN2_MDI3­R2 LAN2_MDI0+ R11 LAN1_TCT
R3 LAN2_MDI0- H1 GND_LAN
R4 LAN2_MDI1+ H2 GND_F1
R5 LAN2_MDI1- L1 LAN2_LED1_Z_ACT#
R6 LAN2_TCTG L2 +V3.3_LAN2
R7 LAN2_MDI2+ L3 LAN2_LED2_Z_1G#
R8 LAN2_MDI2- L4 LAN2_LED0_Z_100M#

UTX-3117 User Manual 20

2.2.21

High Definition Multimedia Interface(HDMI1)

Pin Signal Pin Signal

1 HDMI1_Z_D2+ 11 GND
2 GND 12 HDMI1_Z_CLK­3 HDMI1_Z_D2- 13 x
4 HDMI1_Z_D1+ 14 x
5 GND 15 HDMI1_SCL
6 HDMI1_Z_D1- 16 HDMI1_SDA
7 HDMI1_Z_D0+ 17 GND
8 GND 18 +V5_HDMI
9 HDMI1_Z_D0- 19 HDMI1_HPD
10 HDMI1_Z_CLK+

2.2.22

DisplayPort (DP1)

Pin Signal Pin Signal

1 DP1_0+ 11 GND
2 GND 12 DP1_3­3 DP1_0- 13 DP1_AUX_EN#
4 DP1_1+ 14 GND
5 GND 15 DP1_AUX+
6 DP1_1- 16 GND
7 DP1_2+ 17 DP1_AUX­8 GND 18 DP1_ DP_HPD
9 DP1_2- 19 GND
10 DP1_3+ 20 +V3.3_DP1

21 UTX-3117 User Manual

Chapter

2

Jumper

and

Connector

List

2.2.23

DDR3L SO-DIMM Socket (DIMMB1)

2.2.24

SATA LED(D10)

2.2.25

Power Button(PWRBTN1)

UTX-3117 User Manual 22

Chapter 3

3

Peripheral Installation

3.1

HDD Installation

1. Unscrew the botto m cover screws.

2. Secure 2.5" SATA HDD onto the bottom cover. The screws are in the accessory

box.

UTX-3117 User Manual 24

3. Connect SATA signal and power cable to the 2.5" SATA HDD.

4. Secure the bottom cover in its original position.

25 UTX-3117 User Manual

Chapter

3

Peripheral

Installation

3.2

Mini PCIe Module Installation

1. Unscrew the botto m cover screws.

2. Insert Mini PCIe module into the slot and secure the screw to fix the module.

UTX-3117 User Manual 26

3. Connect the antenna cable to module.

4. Secure the bottom cover in its original position.

27 UTX-3117 User Manual

Chapter

3

Peripheral

Installation

UTX-3117 User Manual 28

Chapter 4

4

BIOS Setup

4.1

Introduction

AM I BIOS has been integrated into many, many motherboards for decades. With the
AM I B IOS Setup program, users can modify B IOS settings and control various sys­tem features. T his chapter des crib es the basic navigatio n of the UTX-3117 B I O S
set up s creen s.

AMI's B IOS ROM has a built-in Setup program that allows users to modify the basic
system configuration. This information is stored in flash R O M so it retains the Setup
information when the power is turned off.

Note! Default BIOS is supported for 64-bit OS installation, if you have any

BIOS setting requirement, please contact with sales representative for
details.

Control Keys

<  ><  ><  ><  > Move select item
<Enter> Select item

<E sc>

Main Menu - Quit without saving changes to the CM OS

Sub Menu - Exit current page and return to the Main Me nu
<Page Up /+> I nc rease the n umeric value or make c hange s
<Page Down/ -> Decrease t he nume ric value or ma ke ch anges
<F1> Gener al help, for Setup Sub Me nu
<F2> Item help
<F5> Loa d previous values
<F7> Loa d setup defaults
<F10> Save all CMO S chan ge s

UTX-3117 User Manual 30

4.2

Entering Setup

4.2.1

Main Menu

Press <Del> to enter AMI BIOS CMOS Setup Utility, the Main M enu will appear on
the screen. Use arrow keys to select amo ng the items and press <Enter> to accept or
enter the s ub-menu.

The Main BIOS setup scr een ha s t w o ma i n frames. The left fr a me displays all the
options that can be configured. Grayed-out options cannot be configured; options in
blue can. The right frame displays the key legend.

Above t h e key l e gend is an a rea r eserve d for a t ext message. W hen an o ption is
selected in the left frame, it is highlighted in white. Often a text message will accom­pany it.



System time / System date

Use this option to ch ange the sys tem t ime and date. Highlight System T ime or
System Date using the <Arrow> keys. Enter new values through the keyboard.
Pr ess the <Tab> key or the < Ar r o w > keys to move bet ween fie lds. T h e da te
must be entered in MM/DD/YY format. The time must be entered in HH:MM:SS
format.

31 UTX-3117 User Manual

Chapter

4

BIOS

Setup

4.2.2

Advanced BIOS Features

Se lect the Ad v a nced t ab fr o m th e UT X -3117 set u p s creen to e nter th e A d vanced
BIO S S etu p scre en. Yo u can select any of the items in the left frame of the screen,
such as CPU Configuration, to go to the s ub me nu for that item. You can display an
Advanced BIOS Setup option by highlighting it using the <Arrow> keys. All Advanced
BIOS Setup options are described in this section. T he Advanced BIOS Setup screen
is shown below. The s ub menus are described on the following pages.

UTX-3117 User Manual 32

4.2.2.1

Realtek PCIe GBE Family Controller Status

Check the status of Realtek LAN port.

4.2.2.2

Check Intel® I201 Gigabit Network connection Status

33 UTX-3117 User Manual

Chapter

4

BIOS

Setup

4.2.2.3

Trusted Computing

UTX-3117 User Manual 34

 Security Device Support

Enable or disable BIOS support for security device.

4.2.2.4

APCI Settings

35 UTX-3117 User Manual

Chapter

4

BIOS

Setup

 Enable ACPI Auto Configuration

Enable or disable BIOS ACPI auto configuration.



Enable Hibernation

This item allows users to enable or disable hibernation.



ACPI Sleep State

This item allows users to set the A CPI sleep state.

 Lock Legacy Resource

This item allows users to lock legacy device resources.

UTX-3117 User Manual 36

4.2.2.5

NCT5523D Super IO Configuration

37 UTX-3117 User Manual

Chapter

4

BIOS

Setup

 Serial Port 1&2 Configuration

This item allows users to enable or disable serial Ports 1/2



Change Settings

This item allows users to change the serial port 1/2

4.2.2.6

Hardware Monitor

UTX-3117 User Manual 38

This item allows you to monitor HW status



Execute Disable Bit

This item allows users to enable or disable the No-Execution page protection.



Intel Virtualization Technology

When enabled, a V MM can utilize the additional hardware capabilities provided
by Vanderpool Technology.

39 UTX-3117 User Manual

Chapter

4

BIOS

Setup

 Digital I/O Configuration

This item will allow users to set up Digital I/O 1~8 to "input" or "output".

UTX-3117 User Manual 40

 Wake System From S5

Enable or disable system wake on alar m event.

41 UTX-3117 User Manual

Chapter

4

BIOS

Setup

 Console Redirection

This item allows users to enable or disable console redirection.

4.2.2.7

CPU Configuration

This page shows CPU Information.

 Active Power Cores

UTX-3117 User Manual 42

Nu mber of cores to enable in each processor p ackage

 Intel Virtualization Technology

When enabled, a V MM can utilize the additional hardware capabilities provided
by Vanderpool Technology.

 VT-d

Enable or disable VT-d

 Bi-directional PROCHOT

When a processor therm al sensor tr ips (eit her c ore), the P ROCHOT# w ill be
driven. If bi-direction is enabled, external agents can drive PROCHOT# to throt­tle the processor.

 Thermal Monitor

Enable or disable Thermal Monitor



Monitor Mwait

Enable/disable Monitor Mwait.



P-STATE Coordination

Change P-STATE Coordination type.

43 UTX-3117 User Manual

Chapter

4

BIOS

Setup

 EIST

Enabled or disabled Intel Spee d Step function.

 Turbo Mode

Enabled or disabled Turbo Mode



Boot performance mode

Select the performance state that the BIOS will set before OS handoff.

UTX-3117 User Manual 44

 C-States

Enabled or disabled C-States

 Enhanced C-States

Enabled or disabled C1E. Wh e n enabled, C P U will switch to m i nimum speed
when all cores enter C-State.

 Max Package C State

Controls the max package C state that the processor will support.

 Max Core C State

This option controls the Max Core C State that cores will support.



C-State Auto Demotion

Configure C-State Auto Demotion.



C-State Un-Demotion

Configure C-State Un-demotion.



Power Limit 1 Enable

Enable/Disable Power Limit 1.



Power Limit 1 Clamp Mode

Enable/Disable Power Limit 1 Clamp Mode.



Power Limit 1 Power

Power Limit 1 in Watts. Auto will program Power Limit 1 based on silicon default
support value.



Power Limit 1 Time Window

Power Limit 1 Time Window Value in seconds. Auto will program Power Limit 1
Time Window based on silicon default support value.

45 UTX-3117 User Manual

Chapter

4

BIOS

Setup

 Network Stack

Enable or disable UEFI Network Stack.

UTX-3117 User Manual 46

 CSM Support

Enable or disable C SM Support..

4.2.2.8

NVMe Configuration

47 UTX-3117 User Manual

Chapter

4

BIOS

Setup

4.2.2.9

USB Configuration

UTX-3117 User Manual 48

 Legacy USB Support

Enables support for legacy USB. Auto option disables legacy support if no USB
devices are connected. DISABL E option will keep US B devices available only
for EFI applications.

 XHCI Hand-Off

This is a workaround for OS without XHC I hand-off support. The XHCI owner­ship change should claim by XHCI driver.

 USB Mass Storage Driver Support

This item allows you to enable or disable the USB mass storage device support.



USB transmit time-out

US B mass storage device transmit c ommand time-out.

 Device reset time-out

US B mas s storage device start unit c ommand time-out.



Device power-up delay

Max i mum time the device will take before it properly r eports itself to the host
controller. “Auto” uses default value: for a Root port it is 100ms, for a Hub port
the delay is taken from Hub descriptor.



Mass storage device

Mass storage device emulation type. 'AUT O' enume rat es devic es according to
their media for mat. Optic al drives are emulat ed as 'CDRO M ', dr ives with no
media will be emulated according to a drive type.

49 UTX-3117 User Manual

Chapter

4

BIOS

Setup

4.2.2.10

Platform Trust Technology



fTPM

Enabled or disabled fTPM.

UTX-3117 User Manual 50

4.2.2.11

Security Configuration



TXE HMRFPO

This item allows users to enable or disable TXE HMRFPO.

 TXE EOP Message

Se nd E OP M essa ge before Enter OS.

51 UTX-3117 User Manual

Chapter

4

BIOS

Setup

4.2.3

Chipset

4.2.3.1

North Bridge

UTX-3117 User Manual 52

53 UTX-3117 User Manual

Chapter

4

BIOS

Setup



OS Selection

Select the target OS.

4.2.3.2

Uncore Configuration

UTX-3117 User Manual 54

55 UTX-3117 User Manual

Chapter

4

BIOS

Setup

 Chipset SATA

Enables or disables the chipset S A T A controller. T he chipset S A T A controller
supports the 2 black internal SATA ports (up to 3Gb/s supported per port).

 SATA Mode Selection

This item allows users to select mode of SATA controller(s).

 Aggressive LPM Support

This item allows users to enable or disable Aggressive LPM Support.



Port 1

This item allows users to enable or disable the Serial -ATA Port 1 device.



Spin Up Device

This item allows users to enable or disable the Spin Up Device.



SATA Device Type

Identify the SATA port is connected to Solid State Drive or Hard Disk Drive.

 Port 2

This item allows users to enable or disable the Serial-ATA Port 2 device



Spin Up Device

This item allows users to enable or disable the Spin Up Device.



SATA Device Type

Identify the SATA port is connected to Solid State Drive or Hard Disk Drive.

UTX-3117 User Manual 56

57 UTX-3117 User Manual

Chapter

4

BIOS

Setup

UTX-3117 User Manual 58

4.2.4

Security Boot

59 UTX-3117 User Manual

Chapter

4

BIOS

Setup

4.2.4.1

Security Boot



Attempt Secure Boot

Secure Boot activated when platform ke y(PK) is enrolled, system mo de is user/
deployed, and CSM function is disabled.

Secure Boot Mode

UTX-3117 User Manual 60

Secure Boot mode - Custom & Standard, Set UEFI Secure Boot Mode to STAN­DARD mode or CUSTO M mode, this change is effect after save. And after eset,
the mode will return to STANDARD mode.

4.2.5

Boot



Bootup NumLock State

Select the keyboard NumL ock state.



Quiet Boot

Enables or disables Quiet Boot option.

61 UTX-3117 User Manual

Chapter

4

BIOS

Setup

4.2.6

Save & Exit

UTX-3117 User Manual 62

63 UTX-3117 User Manual

Chapter

4

BIOS

Setup

www.advantech.com

Please verify specifications before quoting. This guide is intended for reference
purposes only.
All product specifications are subject to change without notice.
No part of this publication may be reproduced in any form or by any means,
electronic, photocopying, recording or otherwise, without prior written permis-
sion of the publisher.
All brand and product names are trademarks or registered trademarks of their
respective companies.
© Advantech Co., Ltd. 2018

Our company network supports you worldwide with offices in Germany, Austria, Switzerland, Great Britain and
the USA. For more information please contact:

Headquarters

Germany

FORTEC Elektronik AG

Lechwiesenstr. 9
86899 Landsberg am Lech

Phone: [phone]
E-Mail:

[e-mail]

Internet: www.fortecag.de

Fortec Group Members

Austria

FORTEC Elektronik AG

Office Vienna

Nuschinggasse 12
1230 Wien

Phone: [phone]
E-Mail:

[e-mail]

Internet: www.fortec.at

Germany

Distec GmbH

Augsburger Str. 2b
82110 Germering

Phone: [phone]
E-Mail:

[e-mail]

Internet: www.distec.de

Switzerland

ALTRAC AG

Bahnhofstraße 3
5436 Würenlos

Phone: [phone]
E-Mail:

[e-mail]

Internet: www.altrac.ch

United Kingdom

Display Technology Ltd.

5 The Oaks Business Village
Revenge Road, Lordswood
Chatham, Kent, ME5 8LF

Phone: [phone]
E-Mail:

[e-mail]

Internet: www. displaytechnology.co.uk

USA

Apollo Display Technologies, Corp.

87 Raynor Avenue,
Unit 1Ronkonkoma,
NY 11779

Phone: [phone]
E-Mail:

[e-mail]

Internet: www.apollodisplays.com