Adtec RD-60 User Manual

RD-60

Integrated MultiCODEC Receiver/Decoder

Thank you for your purchase of the Adtec RD-60 Receiver/Decoder. This
product is sold with optional demodulator hardware packages. Configurations and
indicators relevant to those add-on package are noted here. If you purchased this
product without a demodulator, please disreguard settings noted with an asterisks.

Quick View Status

For information on the core systems of the IRD, use
the down arrorw on the front panel to scroll through
these quick view menus.

Decoder Activity TMR Encryption

DECODING ASI TMR:20.000M CAS:Free to Air
SVC: 00001 “Serv. Name” “Serv. Provider”

Service ID Service Name Service Provider

CODEC Chroma Bit Depth Delay Mode

COD: H.264 CHR: 422 BITD:08 DLYM: NORMAL
VRT: 18.012Mb/s RES:1920X1080 FR:59i

Video Rate Resolution Frame Rate

Video PID PCR PID PMT PID Aspect Ratio

VID:441 PCR:441 PMT:440 ARA:16X9

Audio 1-8

Type Bitrate

1:MU 384k 2:MU 384k 3:MU 384k 4:MU 384k
5:MU 384k 6:MU 384k 7:MU 384k 8:MU 384k

Audio PIDS 1- 8

Audio 1:11300 2:11400 3:11500 4:11600
PIDS 5:11300 6:11400 7:11500 8:11600

Input Mode/FEC Rcv Level Link Margin

RF1 32APSK9/10 Lvl: -52.0dB LMar:20.5dB
Locked DVB-S2 Sym:29.970Ms Eb/No:29.8dB

Lock Status Type Symbol Rate Eb(s)/No

RTP Detected RTP Error Count Buer

RTP: Y RTP-Err: 1234567 Buer:1234ms
FEC: Y FecLoss: 1234567 FecCorr: 1234567

FEC Detected FEC Packet Loss FEC Corrections

Reset:

Should you need to reset your device, you can do
so via the front panel by pressing the MODE,
ESCAPE and RIGHT ARROW keys simultaneously.

LED Status

Decode
Off - Decoder is idle
On - Decoder is active

ASI/IP/RF

Off - No services detected
On - Services detected

Lock 1 / Lock 2

Off - Tuner is not locked
On - Tuner is locked

IP Out

Off - Not functional
On - Not functional

Bars

Off - B/T/ID options are disabled
On - B/T/ID are enabled

A1 - A8

Off - No Audio Decoding
On - Audio Decoding
Blinking - Fail to decode or pass
audio

Alarm

Off - No system alarms

ASI

A2

IP

MultiCODEC
Receiver / Decoder

A3

On - System alarm

BISS

Off - Decryption config is OFF
On - Decryption config is ON

Busy

Off - No network activity
On - Network traffic present

Link

Off - No network detected
On - Connection active

Decode

RD-60

A1

Quick Start Guide

Services

ASI RF1 RF2 IP

Select Service

Select First

The two Gain settings
only apply to RD60-PRM
units manufactured prior
to 03/12 with special
rmware. Units
manufactured after this
date handle these
setting automatically.

RF Rx*

PRM & ADV

Select Tuner

Local Oscillator

Manual LO

Downlink

L-Band

Mod. Type

CCM Mode

Mod. Mode

Symbol Rate

Acquisition Range

Roll O

Pilot

Fec Frame Type

RF Gain

BB Gain (PRM Only)

(PRM Only)

LNB Menu

RF Rx*
LB

<< RF1 - RF2 >>

Tuner State

Downlink

Local Oscillator

Manual LO

L-Band

Acqusition Range

S2X Rollo

LNB Polarity

LNB Tone

Modulation Type

Symbol Rate

ISI

RF Stats

Front Panel Menus:

Use Mode Button to move

MODE

through top layer menus.

Use arrows for navigation

in submenus.

RF

Lock 1

Lock 2

IP Out

Bars

Alarm BISS

Busy

Link

A8

A7

A6

A5

A4

DECODING ASI TMR:20.000M CAS:Free to Air
SVC: 00001 “Service Name” Service Provider

Use select to enter into edit

SELECT

mode and enter to

save selection.

RF Rx*
STD

<< RF1 - RF2 >>

Tuner Active

Local Oscillator

Manual LO

Downlink

L-Band

Mod. Type

Mod. Mode

Symbol Rate

Aquisition Range

Roll O

Pilot

LNB State

LNB Polarity

LNB Tone

ENTER

IP Rx

Rx IP

Rx Port

SSM Address

Video

Output Menu

Genlock Menu

Audio Assign Order

Audio Sync Mode

<< AUDIO 1-8 >>

Connector

Latency

Time Out

Error Rec.

Dolby E Line

Dolby D Mode

ANALOG VOL.

(Audio 1-2 only)

Units ship with the front panel
logged in by default. If you become
logged out and are prompted for a
password, use the following key
sequence for access.

Press <Select> when panel displays
‘User Login -- logged out’
Press <Up arrow>
Press <Select>
Press <Enter>
Press <Right arrow>
Press <Enter>

Audio

Audio PID

Oset

SDI Matrix

SELECT

ENTER

VBI

TimeCode Menu

AFD Menu

CC Menu

Teletext Menu

CAS

Mode

Clear SW

Encrypt. SW

User ID 1

User ID 2

TS Out Decrypt

System

Login

Duration

Backlight

Network Menu

Time Menu

NTP Menu

Alarm Menu

SNMP Menu

COM2

Name

Firmware

Feature Menu

Model Indicators:

Premium demodulator (PRM)

Advanced demodulator (ADV)

L-Band demdulator (LB)

Standard demodulator (STD)

No demodulator

Special Keys:

Use the F2 button as a decimal.

F2

3def

2abc

MODE

ESCAPE

1

4ghi

7pqrs

F1

5jkl

8tuv

6mno

9wxyz

F2

0

Adtec Digital US Sales [phone] International Sales [phone] www.adtecdigital.com 2015 Adtec Digital

Getting Connected

To begin, you will need to connect to your RD-60 via ethernet
directly, or by adding the RD-60 to your local area network.The default
address for all Adtec devices is 192.168.10.48.

To connect directly to the device, make sure that your computer
and the device have IP addresses within the same IP class range (ex.

192.168.10.48 for the device and 192.168.10.49 for your computer).
If you need to change the IP address of the device, this can be done via
the front panel, System > Network menu. Using a CAT 5 crossover
cable, connect one end to your computer and the other to the Ethernet
port found on the processor section of the back panel. (Some computers
can auto negotiate the connection and a crossover may not be
necessary.)

To add the device to a LAN, connect a standard Ethernet cable to
your network router and then to the Ethernet port on the back of the
device. If your network is DHCP enabled and you prefer that over a
static IP, you can turn on DHCP for the device via the front panel,
System > Network menu.

Web-Based Control Application

Adtec Digital has adopted
zero-conguration networking
technology, streamlining the setup and
conguration processes for our products.
The use of this technology enables
automatic discovery of Adtec devices and
services on an IP network. Used in tandem
with the web-based control and
conguration applications we can now
provide 1-click access to any device.
By using the built-in Bonjour
Apple's
readily available for IE

©

Safari© browser or the plug-ins

©

or Firefox©

©

locater in

browsers, users can locate all of the Adtec
devices on a network by referencing the

serial number on the back of the device. Clicking on the unit in the Bonjour

©

list will re-route you to a
login page. If you do not wish to use Bonjour, you can reach the device’s web application by pointing
your browser to the IP Address of the device. Ex. http://192.168.10.48/. You will be prompted for a
username and password. The default username is ‘adtec’. The default password is ‘none’.

The left-hand panel of the application will report current status in real-time while the right

panel tabs will allow you to congure your device.

Have questions? Each field or group of fields in

our web-based application has a hint button associate

?

with it. It contains information on use of the field or
acceptable ranges.

Getting Started

Once your receiver is powered up, configured on
your network and you have inputs applied with active
services, you can select which services you want to
decode via the web-based control application. The below
image shows the Input > RD Services tab. From this tab,
you can view all services available on your device, select
one of the services for decode or view more details about
the service. There is a ‘Select First Found’ option for each
input. When selected, this configuration will detect the
first service detected in the PAT table of the input and
decode it.

Power .....................................................................................................................................

Power: 1 & 2 Redundant AC Power, Standard 3 pin computer power plug

(Auto range 70-240 VAC Input)

Processor ..............................................................................................................................

GigE: MPEG2 or RTP multicast transport ingress port. Current Contraints: 1 - 100 Mbps
COM2: API Serial Communication Interface
COM1: Serial Port Used for Troubleshooting (Terminal)
Ethernet: 10/100 base T ethernet interface (Monitoring/Management)
RS422: Not Currently Supported
Parport: 9-pin parallel I/O interface for control systems
GPIO: Tally and Control Port

Decoder .............................................................................................................................

Analog Audio Out: Balanced analog audio out. Stereo pairs 1 & 2
AES Audio Out 1-4: 75 Ohm AES-3 BNC
ASI In: 75 Ohm BNC
DVB-ASI x3 Out: 75 Ohm BNC
DVB-ASI In: 75 Ohm terminated. ASI Transport Stream Input
Sync In: Standard analog video sync separation for NTSC, PAL, 480I/P, 576I/P, 720P, and 1080I/P/PsF from

Composite Video (CVBS). Bi-level & tri-level sync compatible. BNC
CVBS Out: 75 Ohm Standard Denition Composite Video Output BNC
SDI Out Banks: (2) 75 Ohm Outputs from decoder: Video/Audio/VBI (SMPTE 259M-C - SD & SMPTE 292M - HD) BNC

Demodulator (optional)*......................................................................................................................

RF 1 & 2: RF input, 75 Ohm F-Connector
Advanced (ADV) Model: Supports L-Band, DVB-S/S2, QPSK, 8PSK, 16APSK.
L-Band (LB) Model: Supports L-Band, DVB-S/S2, QPSK, 8PSK, 16APSK, 32APSK.
Premium (PRM) Model: Supports L-Band, DVB-S/S2, QPSK, 8PSK, 16APSK, 32APSK.
Standard (STD) Model: Supports L-Band, DVB-S/S2, QPSK, 8PSK 1-30 Mbaud.

Demodulator notes: Field upgradable demodulator keys are required to unlock full capability such as 16/32APSK. The STD demodulator has been discontinued.

Power

1

Demodulator

2

RF 1

RF 2

GigE

COM2

GPIO

COM1

Ethernet

DVC

Parport

Processor

RS422

ASI Out X 3

Analog

Audio 1

DVB

ASI In

Analog

Audio 2

AES Audio

In 1-4

Note: IP service selection is treated differently than ASI or RF
inputs. To populate the IP services section, you need to first

Sync In

CVBS Out

SDI Out

1 & 2

SDI Out

1 & 2

Decoder

visit the IP Params tab and set the correct Multicast RX, port
and handling parameters. Return to the RD Services tab. Click
the ‘Select First Found’ radio button for IP. This will populate
the RD Services tab with services found on the IP input.

The most recent firmware releases are available on our
support website, www.adtecdigital.com. Advanced users can
find direct API command help as part of the on-board web
application, Help Tab.

Adtec Digital Technical Support: 615.256.6619 www.adtecdigital.com FW: 1.13.XX March 2015