Adtec mediaHUB-HD 422 Quick Start
TM
Multi-CODEC HD 422 Encoder
Quick Start Guide
Getting Started
Thank you for your purchase of the Adtec mediaHUB-HD 422 Encoder.
This Multi-CODEC Encoder supports both MPEG 2 and MPEG 4 AVC standard and
high definition encoding at 420 and 422 profiles. Further instructions are available
via the manual integrated into the on-board software. You can view it by looking
for the HELP tab once your unit is powered up and you are connected to the
web-application. See back for more details. This manual and the most recent
firmware are available on our support website, www.adtecinc.com. Advanced users
can also find direct API command help as part of the on-board web application.
Front Panel LEDs:
Encode
Not Active
Pre-rolling
(Studio Encoding)
Encoding
Transition
Video
No Video
(Encoding to Idling)
(Audio Only)
Video Present
Not Supported
No Video Present
Resolution
Standard Definition
1080i HD
720p HD
Audio 1 - 4
Audio Not Enabled
Audio Enabled
(NTSC / PAL)
Control
Control Mode Off
Control Detected/Remote Mode
Control Detected/Local Mode
Alarm
No Encoder Alarm
Encoder Alarm
MP2/AVC
Encoding MPEG 2
Encoding MPEG 4 AVC
420/422
Encoding 4:2:0 Chroma
Encoding 4:2:2 Chroma
Front Panel Menus:
Use Mode Button to move through top layer menus.
Use arrows for navigation in submenus.
Use select to enter into edit mode and enter to save selection.
System
Login
Duration
Network
Time
NTP
Alarm
Mirror
COM2
Firmware
Decoder
Status
Conf. Decode
Auto Res.
Display
DVB-ASI Menu
Aud. Track
SDI Aud. Matrix
Encoder
Video
Status
Rate
CODEC
Chroma
Input
GOP
GOP Str.
GOP Size
SDI Pass
Latency
Encoder
Audio
Sample Freq.
A1 A2
A3 A4
Sync
Input
Mode
Typ e
Bitrate
Volume
Transmit
Mux Rate
Vid. AutoFill
IP Destinations 1-4
PID
PCR
Prog. No.
Map PID
Vid. PID
Aud.1 PID
Aud. 2 PID
Aud. 3 PID
Aud. 4 PID
AMOL
Splice
VITC Mode
VITC PID
VBI Source
Closed Cap.
Service Name
Table
Table
Prole
Load
Save
Encrypt.
Mode
Clear Word
Encrypt Word
User ID 1
UserID 2
Units ship with the front panel
logged in by default. If you become
logged out and are prompted for a
password, use the following key
sequence for access.
Press <Select> when panel displays
‘User Login -- logged out’
Press <Up arrow>
Press <Select>
Press <Enter>
Press <Right arrow>
Press <Enter>
Decode
Not Active
Decoding
Resolution
Standard Definition
1080i HD
720p HD
CDE/ASI
Confidence Decoding
ASI Recieving
Adtec Digital Technical Support: 615.256.6619 www.adtecinc.com 06.28.10
System LED Status
Power
Power is OFF
Power is ON
Alarm
No System Alarm
Minor Alarm
Major Alarm
Link
No Link Detected
Link Active
Busy
No Network Traffic
Network Traffic Present
Aux
(Not Used)
Front Panel Status
Video Resolution Frame Rate Video Bit Rate
1920x1080 29i 33.77M
1DD 192K 2DD 192K 48
Audio Input 1 & 2 Sampling Rate
Getting Connected
Web-Based Control Application
To begin, you will need to connect to your mediaHUB-HD 422 via
ethernet directly, or by adding the mediaHUB-HD 422 to your local area
network.The default address for all Adtec devices is 192.168.10.48.
To connect directly to the device, make sure that your computer
and the device have IP addresses within the same IP class range (ex.
192.168.10.48 for the device and 192.168.10.49 for your computer). If
you need to change the IP address of the device, this can be done via
the front panel, System > Network menu. Using a CAT 5 crossover
cable, connect one end to your computer and the other to the Ethernet
port found on the processor section of the back panel. (Some computers
can auto negotiate the connection and a crossover may not be
necessary.)
To add the device to a LAN, connect a standard CAT 5 Ethernet
cable to your network router and then to the Ethernet port on the back
of the device. If your network is DHCP enabled and you prefer that over
a static IP, you can turn on DHCP for the device via the front panel,
System > Network menu.
the device. Ex. http://192.168.10.48.
The left panel of the application will report current status in real-time while the right panel tabs will
allow you to congure your device. Additional hints regarding conguration options can be found by clicking on
the hints buttons
associated with each
eld or group of elds.
Condence Decode ................................................................................................
ASI IN Asynchronous Serial Interface per EN500083-9 BNC 75 Ohm.
HD/SD SDI Out User Dened (D1-1080i). SMPTE (SD)259/(HD)292 Video and (SD)272/(HD)299 Audio
HDMI HDMI v1.3, HDCP v1.2, and DVI v1.0 compliant output.
GigE MPEG2 or RTP multicast transport egress port (SMPTE 2022)
CVBS Out 75 Ohm terminated NTSC or PAL D1 Composite Video Output
Processor .................................................................................................................
COM2 API Serial Communication Interface
COM1 Serial Port Used for Troubleshooting (Terminal)
Ethernet 10/100 base T ethernet interface
USB 2.0 Not Currently Supported
Encoder.....................................................................................................................
ASI OUT 75 Ohm source ASI x3 per EN500083-9
CVBS In 75 Ohm terminated NTSC or PAL D1 Composite Video Input
SDI In 75 Ohm terminated Input, Video & Audio (SMPTE 259M for SD & SMPTE 292M for HD) BNC
SDI Out 75 Ohm re-clocked source matched to Input Signal
RS422 Sony 9-pin electrical and protocol tape deck interface. Controller and Device Modes
GPIO Tally and Control Port
AES Audio In 1-4 75 Ohm AES-3 per AES3-2003
AES Audio Out 1-2 Compressed Dolby Bit Stream Out
Analog Audio In Stereo Pairs 1 and 2 600 Ohm Balanced.
ASI In
CONFIDENCE DECODE
?
HD-SDI Out
HDMI
GigE
CVBS Out
COM2
COM1
Ethernet
PROCESSOR
USB 2.0
Adtec Digital has adopted zero-conguration
networking technology, streamlining the setup and
conguration processes for our products. The use of this
technology enables automatic discovery of Adtec devices
and services on an IP network. Used in tandem with the
web-based control and conguration applications we can
now provide 1-click access to any device.
©
By using the built-in Bonjour
©
browser or the plug-ins readily available for IE© or
Safari
©
browsers, users can locate all of the Adtec
Firefox
locater in Apple's©
devices on a network by referencing the serial number on
the back of the device. Clicking on the unit in the
©
Bonjour
list will re-route you to a login page. If you do
not wish to use Bonjour, you can reach the device’s web
application by pointing your browser to the IP Address of
SDI Out
RS422
GP IO
ASI Out X 3
C VBS In
SDI In
AES Audio In 1-4
Analog Audio In
ENCODER
AES Audio Out 1-2
Adtec Digital Technical Support: 615.256.6619 www.adtecinc.com 06.28.10
Loading...