ADLINK NuPRO-E72 User Manual

Download

NuPRO-E72

PICMG® 1.3 Full Size LGA1150 Intel® Xeon® E3-

1200v3 Processor-Based SHB

User’s Manual

Manual Rev.: 2.05 Revision Date: Apr. 24, 2015 Part No: 50-13074-1010

Advance Technologies; Automate the World.

Revision History

Revision Release Date Description of Change(s)

2.00 2014/9/30 Initial release

2.05 2015/4/24 Procedural errata rectified

NuPRO-E72

Preface

This document contains proprietary information protected by copyright. All rights are reserved. No part of this manual may be reproduced by any mechanical, electronic, or other means in any form without prior written permission of the manufacturer.

Disclaimer

The information in this document is subject to change without prior notice in order to improve reliability, design, and function and does not represent a commitment on the part of the manufacturer.

In no event will the manufacturer be liable for direct, indirect, special, incidental, or consequential damages arising out of the use or inability to use the product or documentation, even if advised of the possibility of such damages.

Environmental Responsibility

ADLINK is committed to fulfill its social responsibility to global environmental preservation through compliance with the European Union's Restriction of Hazardous Substances (RoHS) directive and Waste Electrical and Electronic Equipment (WEEE) directive. Environmental protection is a top priority for ADLINK. We have enforced measures to ensure that our products, manufacturing processes, components, and raw materials have as little impact on the environment as possible. When products are at their end of life, our customers are encouraged to dispose of them in accordance with the product disposal and/or recovery programs prescribed by their nation or company.

Trademarks

Product names mentioned herein are used for identification purposes only and may be trademarks and/or registered trademarks of their respective companies.

Preface iii

Conventions

Take note of the following conventions used throughout this manual to make sure that users perform certain tasks and instructions properly.

Additional information, aids, and tips that help users perform tasks.

NOTE:

Information to prevent minor physical injury, component damage, data loss, and/or program corruption when trying to com-

CAUTION:

WARNING:

plete a task.

Information to prevent serious physical injury, component damage, data loss, and/or program corruption when trying to complete a specific task.

iv Preface

NuPRO-E72

Revision History...................................................................... ii

Preface.................................................................................... iii

List of Figures........................................................................ ix

List of Tables.......................................................................... xi

1 Introduction........................................................................ 1

1.1 Overview.............................................................................. 1

1.2 Features............................................................................... 1

1.3 Specifications....................................................................... 2

1.4 Block Diagram ..................................................................... 4

1.5 Functional Description ......................................................... 4

1.6 Mechanical Drawing ............................................................ 7

1.7 I/O Connectivity ................................................................... 8

1.8 Power Consumption .................................. ... ... .... ... ... ... .... ... 9

1.8.1 Intel® Xeon® Processor E3-1225 v3 3.2GHz

(84W)..........................................................................9

1.8.2 Intel® Xeon® Processor E3-1268L v3 2.30 GHz

(45W)........................................................................10

1.8.3 Intel® Core™ i3-4330 Processor 3.5GHz (54W)...... 11

1.8.4 Intel® Celeron® G1820 Processor 2.7GHz (53W)...12

1.9 Rear I/O Panel................................................................... 13

1.10 Board Layout ..................................................................... 16

1.11 Onboard Connectors ......................................................... 17

2 Getting Started................................................................. 23

2.1 Package Contents ............................................................. 23

2.2 Installing the CPU.............................................................. 23

2.3 Installing the CPU Fan and Heatsink................................. 27

Table of Contents v

2.4 Installing Memory Modules................................ ... .... ... ... ... 27

2.5 Jumpers & Switches .......................................................... 29

2.6 Driver Installation......................... ... ... ... ............................. 31

2.6.1 Installing Chipset Driver............................................32

2.6.2 Installing Graphics Driver.........................................32

2.6.3 Installing Ethernet Driver ..........................................32

2.6.4 Installing Management Engine Driver ... ... ... .... ... ... ....32

2.6.5 Installing USB 3.0 Driver...........................................32

A Appendix: BIOS Setup.......................................................35

A.1 Starting the BIOS............................................................... 35

A.2 Main Setup......................................................................... 39

A.3 Advanced BIOS Setup....................................................... 40

A.3.1 ACPI Settings .................................................... ... ... .41

A.3.2 Trusted Computing.................................. ... .... ... ... ... .43

A.3.3 CPU Configuration...... ... .... ... ... ... .... ... ... ... ... ..............44

A.3.4 SATA Configuration..................................................46

A.3.5 Intel TXT Configuration.. .... ... ... ... .... ... ... ... ... .... ... ... ... .47

A.3.6 Intel IGD SWSCI OpRegion..................................... .48

A.3.7 USB Configuration....................................................49

A.3.8 Super IO Configuration.............................................51

A.3.9 Hardware Monitor.....................................................52

A.3.10 AMT Configuration............. ... ... ... .... ... ... ... ... .... ... ... ... .53

A.3.11 Serial Port Console Redirection......... ... ... ... .... ... ... ... .55

A.4 Chipset Setup .................................................................... 58

A.4.1 Graphics and Memory Bridge Configuration.............59

A.4.2 PCH Bridge Configuration ........................................60

A.4.3 Management Engine Subsystem..............................62

A.5 Boot Configuration ............................................................. 64

A.6 Security Setup.................................................................... 66

A.7 Exit Menu........................................................................... 68

vi Table of Contents

NuPRO-E72

B Appendix: Watchdog Timer..............................................71

B.1 Sample Code..................................................................... 71

C Appendix: System Resources..........................................75

C.1 System Memory Map......................................................... 75

C.2 Direct Memory Access Channels............................... ... .... . 75

C.3 IO Map....... ... ... ... ... .... ... ... ....................................... ... ... .... . 76

C.4 Interrupt Request (IRQ) Lines............................................ 77

Important Safety Instructions.............................................. 83

Getting Service...................................................................... 85

Table of Contents vii

This page intentionally left blank.

viii Table of Contents

NuPRO-E72

List of Figures

Figure 1-1: NuPRO-E72 Block Diagram ............................................ 4

Figure 1-2: NuPRO-E72 Board.......................................................... 7

Figure 1-3: Rear I/O Panel..............................................................13

Figure 1-4: NuPRO -E72 Board Topography...................................16

List of Figures ix

This page intentionally left blank.

xList of Figures

NuPRO-E72

List of Tables

Table 1-1: NuPRO-E72 I/O Connectivity ..................... .... ... ... ... .... ... . 8

Table C-1: System Memory Map.....................................................75

Table C-2: Direct Memory Access Channels...................................75

Table C-3: IO Map........................................................................... 76

Table C-4: IRQ Lines PIC Mode............. ... ... .... ... ... ... ... .... ... ... ... .... .. 77

Table C-5: IRQ Lines APIC Mode ............. ... .... ... ... ... ... .... ... ... ... .... .. 79

Table C-6: PCI Configuration Space Map....................................... 81

Table C-7: PCI Interrupt Routing Map................. ... ... ... .... ... ... ... .... .. 82

List of Tables xi

This page intentionally left blank.

xii List of Tables

1 Introduction

1.1 Overview

The ADLINK NuPRO-E72 is a PICMG 1.3 System Host Board

(SHB) supporting 4th Generation Intel Xeon E3-1200 v3, Core i3,

Pentium and Celeron processors in a LGA1150 package to deliver

a scalable high performance platform for a wide array of industrial

applications. The NuPRO-E72 supports 22nm process CPUs at up

to 3.5 GHz with integrated graphics and memory controllers,

Direct Media Interface (DMI) and Flexible Display Interface (FDI)

connectivity to the Intel® C226 Express Chipset. Dual-channel

DDR3 ECC memory is supported up to a maximum of 16 GB in

two DIMM slots.

These advanced features, coupled with PCI Express® x16 expan-

sion capability, dual PCI Express®-based Gigabit Ethernet, SATA

6 Gb/s and USB 3.0 support make the NuPRO-E72 ideal for vision

and automation control applications.

1.2 Features

X Supports 4th Generation Intel

Pentium and Celeron processors

X Integrated Intel X PCI Express x16 expansion, configurable as two PCI

HD Graphics

Express x8 or one PCI Express x8 and two PCI Express x4

X Dual Gigabit Ethernet X 6x USB 3.0 ports (2x on rear panel, 4x on SHB) X 4x USB 2.0 ports on backplane X 4x SATA 6 Gb/s ports on SHB X 6x COM ports (including 1x RS-232/422/485) X Watchdog Timer, Hardware Monitor X Optional HD audio kit (DB-Audio2 daughter board) X TPM hardware security chip X RoHS compliant

Xeon® E3-1200 v3, Core i3,

NuPRO-E72

Introduction 1

To purchase the optional DB-Audio2 daughter board, please contact your ADLINK sales representative.

NOTE:

1.3 Specifications

System

•Intel® Xeon® E3-1275v3, 3.5GHz, 8M Cache, 22nm, 84W TDP, LGA1150 (4C)

•Intel

CPU

•Intel

Chipset Intel® C226 Platform Controller Hub

• 2x 240-pin DIMM sockets

Memory

• Dual-channel DDR 3 ECC/non-ECC 1333/1600 MHz (up

BIOS AMIBIOS in 64-Mbit SPI Flash Audio Watch Dog

Timer Hardware

Monitor

Intel® High Definition Audio support via DB-Audio2 daughter board

1-255 second or 1-255 minute programmable and can generate system reset.

CPU/System temperature, fan speed and onboard DC voltage

TPM Infineon SLB 9635 TT 1.2

• Microsoft® Windows® 7 SP1 64-bit

• Microsoft® Windows® 8.1 64-bit

Operating Systems

• Microsoft® Windows® Server 2008 R2

• Fedora 19 64-bit

• RedHat Enterprise Linux 6.5 64-bit

• Ubuntu 13.10 64-bit

Xeon® E3-1225v3, 3.2GHz, 8M Cache, 22nm, 84W

TDP, LGA1150 (4C)

Xeon® E3-1268Lv3, 2.3GHz, 8M Cache, 22nm,

45W TDP, LGA1150 (4C)

Core™ i3-4330S, 3.5 GHz, 3M Cache, 22nm, 54W

TDP, LGA1150 (2C)

Pentium® G3420, 3.2 GHz, 3M Cache, 22nm, 54W

TDP, LGA1150 (2C)

Celeron G1820, 2.7GHz, 2M Cache, 22nm, 55W

TDP, LGA1150 (2C)

to 16 GB)

2Introduction

I/O Interfaces

• 6x USB 3.0 ports (2x on rear panel, 4x on SHB)

• 4x USB 2.0 on backplane

• 4x SATA 6 Gb/s on SHB

• 6x serial ports via onboard pin-header (5x RS-232, 1x RS-232/422/485 with auto flow control)

I/O Ports

PCIe/PCI

Integrated Integrated Intel® HD Graphics External PCI Express x16

Controller

Ports Two RJ-4 5 Eth ernet ports

Form Factor Standard full-size PICMG 1.3 SHB Dimensions 338 x 126 mm (L x W) Operating

Temp. Storage Temp. -20ºC to 80ºC Rel. Humidity 10% to 90% non-condensing Safety CE, FCC Class A

• 2x Gigabit Ethernet RJ45 ports

• 1x VGA port (Dsub-15)

• 1x DVI-D via onboard pin- header (opt. cable bracket

• Pin header for HD Audio DB-Audio2 daughter board

• 1x PS/2 KB/MS via onboard pin header (op t. cable bracket)

• PCIe-x16 (or two PCIe x8 or one PCIe x8 and two PCIe x4)Gen3

• PCIe-x4 (or four PCIe x1) and PCI 32bit/33MHz (TI XIO2001) via golden fingers

Graphics

Ethernet

• Dual Gigabit Ethernet (Intel® I217LM Gigabit Ethernet PHY, Intel® I211-AT Gigabit Ethernet Controller)

• Supports Preboot Execution Environment (PXE), WakeOn-LAN, and Intel® AMT 9.0 on LAN1 (I217LM)

Mechanical and Environment

0ºC to 60ºC

NuPRO-E72

)

Introduction 3

1.4 Block Diagram

PCIe x16 Gen 3

(discrete graphics or I/O)

Controller

Dual/Quad

core 22nm

Haswell

Graphics

Controller

Memory

Dual Channel

DDR3 ECC 1600

Max. 16GB

x2 Display

Link

Analog VGA

DVI-D

4 USB 2.0 Ports

4 SATA 6 Gb/s

Audio

C226

PCH

x4 DMI

SPI

BIOS

LPC

TPM 1.2

Pin header

for KB/MS

PCIe to PCI

MAC+PHY

Super I/O

IT8786

Intel

I211-AT

ITE

4 PCI

1 PCIe x4 or 4 PCIe x1

6 USB 3.0

Intel

MAC

I217LM

Dual

GbE

6 COM

Figure 1-1: NuPRO-E72 Block Diagram

1.5 Functional Description

Processor Support

The NuPRO-E72 is PICMG 1.3 System Host Board supporting the 4th Generation Intel LGA1150 socket. An integrated memory controller supports dual channel DDR3 ECC and Intel the CPU. The CPU provides a PCI Express x16 for external graphics or expansion. Direct Media Interface (DMI) and Flexible Display Interface (FDI) provide connectivity to the Intel Express Chipset.

Xeon® and Core™ processor family in

HD Graphics is integrated onboard

C226

Intel® C226 Express Chipset

The Intel® DH82C26 Platform Controller Hub (PCH) combines with the processor to provide a compact yet powerful 2-chip solution. Direct Media Interface (DMI) is the chip-to-chip connection

4Introduction

NuPRO-E72

between the processor and PCH. I ntel® F lexible Dis play Inte rface carries display traffic from the integrated graphics in the processor to the legacy display connectors in the PCH. The PCH supports all other required interfaces including PCI Express, SATA 6 Gb/s, USB 3.0, PCI, LPC, and SPI.

Dual-Channel DDR3 ECC Memory

To meet the requirements of memory-intensive applications, the NuPRO-E72 has a dual-channel memory architecture supporting DDR3 ECC 1333/1600 MHz DIMMs. The key advantages of DDR3 ECC are the higher bandwidth and the increase in performance at lower power than DDR2. DDR3 ECC memory technology meets the requirements of the latest 3D graphics, multimedia, and network application, and boosts system performanc e b y eliminating bottlenecks.

Gigabit Ethernet

The NuPRO-E72 utilizes an Intel® I217LM Gigabit Ethernet PHY and Intel® I211-AT Gigabit Ethernet Controller connected to the PCI-E bus of the C226 PCH. Intel® AMT 9.0 (I217LM on LAN1), Wake-on-LAN and PXE are supported.

Serial ATA

The NuPRO-E72 provides four Serial ATA ports with data transfer rates of up to 6.0 GB/s. Intel® Rapid Storage Technology supports AHCI and RAID 0/1/5/10 functionality.

Universal Serial Bus (USB 2.0/3.0)

The NuPRO-E72 provides 4 USB 2.0 ports (backplane) supporting transfer rates up to 480 Mb/s and 6 USB 3.0 ports (2x on rear panel, 4x on SHB) supporting transfer rates up to 5Gb/s. All ports are USB 2.0/1.1 compatible.

Hardware monitoring

A built-in, proactive hardware monitoring system in the Super I/O monitors the CPU temperature, system fan speed, and voltage levels to prevent overheating and/or component damage, effect

Introduction 5

timely failure detection, and ensure stable supply of current for critical components.

Watchdog Timer

The watchdog timer (WDT) monitors system operations based on user-defined configurations. The WDT can be programmed for different time-out periods, such as from 1 to 255 seconds or from 1 to 255 minutes. The WDT generates a reset signal, then a reset request, after failure to strobe it within the programmed time period. A register bit may be enabled to indicate if the watchdog timer caused the reset event. The WDT register is cleared during the power-on sequence to enable the operating system to take appropriate action when the watchdog genera tes a reboot.

Trusted Platform Module

The NuPRO-E72 optionally supports TPM ver. 1.2 (Trusted Platform Module) for secure storage of keys, passwords and digital certificates. Systems supporting TPM offer improved hardwarebased security in numerous applications, such as file and folder encryption, local password management, S-MIME e-mail, VPN and PKI authentication and wireless authentication for 802.1x and LEAP.

Intel® Active Management Technology

Intel® Active Management Technology (Intel® AMT) is hardwarebased technology for remotely managing and securing PCs out-ofband. Intel® AMT includes hardware-based remote management, security, power-management, and remote-configuration features. Intel® AMT allows remote access to a system when traditional techniques and methods are not available.

6Introduction

1.6 Mechanical Drawing

117 111

38.5

NuPRO-E72

6.5

146

333.6

338.1

4.92

20.59

123.09

126.39

Dimensions

in mm

Figure 1-2: NuPRO-E72 Board

Introduction 7

1.7 I/O Connectivity

I/O Bracket Onboard

VGA Y — — DB-15 DVI-D — Y —

LAN1/2 (RJ-45) Y — —

PS/2 KB/MS — Y — USB Rear Panel 2 — — USB 3.0 USB 3.0 headers — 4 — USB backplane — — 4 USB 2.0

COM1-2 — Y — 2.54” pitch COM3-6 — Y — 2.00" pitch SATA — 4 — — PCIe x4 — — Y or four PCIe x1

PCIe x16 — — Y

PCI 32bit/33MHz — — Y via TI XIO2001

Golden Finger

Remarks

cable w/ bracket optional

Act/Link/ Speed LEDs

cable w/ bracket optional

PCI Express x16 expansion can be configured as two PCI Express x8 or one PCI Express x8 and two PCI Express x4

Table 1-1: NuPRO-E72 I/O Connectivity

8Introduction

NuPRO-E72

1.8 Power Consumption

1.8.1 Intel® Xeon® Processor E3-1225 v3 3.2GHz (84W)

System Configurations

Intel

CPU Memory

Slot1 Memory

Slot2 Graphics Intel HDD Seagate ST320LT012 320GB Monitor Acer G246HL Power

Supply Cooler Delta FHSA9025B-1225 Video

Resolution BIOS 0.92

Item

S4 0.10/5.04 0.504 0.11/5.04 0.5544 S5 0.07/5.04 0.7056 0.07/4.96 0.3472

Windows 7 (Idle)

Windows 7 (Typical)

Xeon® Processor E3-1225 v3

(8M Cache, 3.20 GHz) InnoDisk M3U0-8GSSALPC-AC56 8GB DDR3

1600 LV DIMM InnoDisk M3U0-8GSSALPC-AC56 8GB DDR3

1600 LV DIMM

HD Graphics 4600

FSP350-60PFG

1024 x 768 x32bit

BIOS EIST/C-state Enabled

Current (A)/ Voltage (V)

1.04/5.02

0.55/12.08

0.81/3.31

0.73/5.00

0.55/12.12

0.81/3.32

1.13/5.01

4.48/12.05

0.81/3.30

Power (W)

14.5459

27.0201

62.3753

BIOS EIST/C-state Disabled

Current (A)/ Voltage (V)

0.62/5.02

0.55/12.08

0.81/3.31

0.75/5.02

0.55/12.01

0.81/3.30

1.13/5.02

4.26/12.01

0.81/3.30

Power (W)

12.4375

13.0435

59.5082

Introduction 9

System Configurations

Windows 7 (Max loading)

0.82/5.03

8.09/12.01

0.81/3.31

103.9666

0.81/5.02

7.80/12.01

0.79/3.30

100.3512

1.8.2 Intel® Xeon® Processor E3-1268L v3 2.30 GHz (45W)

System Configurations

CPU Memory

Slot1 Memory

Slot2 Graphics Intel HDD Seagate ST320LT012 320GB Monitor Acer G246HL Cooler Delta FHSA9025B-1225 Power

Supply Video

Resolution BIOS 0.92

Item

S4 0.08/5.04 0.4032 0.1 1/5.04 0.5544 S5 0.06/5.04 0.3024 0.04/5.04 0.2016

Windows 7 (Idle)

Intel® Xeon® Processor E3-1268L v3 (8M Cache, 2.30 GHz)

InnoDisk M3U0-8GSSALPC-AC56 8GB DDR3 1600 LV DIMM

HD Graphics 4600

FSP350-60PFG

1024 x 768 x32bit

BIOS EIST/C-state Enabled

Current (A)/ Voltage (V)

0.74/4.98

0.55/12.10

0.82/3.31

0.74/4.98

0.55/12.10

0.80/3.31

Power (W)

13.0544

12.9882

BIOS EIST/C-state Disabled

Current (A)/ Voltage (V)

0.62/5.01

1.04/12.06

0.81/3.31

0.74/4.99

0.59/12.10

0.83/3.31

Power (W)

18.3297

13.5789

10 Introduction

NuPRO-E72

System Configurations

Windows 7 (Typical)

Windows 7 (Max loading)

1.15/4.99

3.35/12.03

0.80/3.30

0.80/4.99

4.80/12.03

0.80/3.30

48.679

64.376

1.07/4.99

3.23/12.04

0.80/3.30

0.81/5.00

4.62/11.99

0.81/3.30

46.8685

62.1168

1.8.3 Intel® Core™ i3-4330 Processor 3.5GHz (54W)

System Configurations

Core™ i3-4330 Processor (4M Cache, 3.50

CPU

Memory Slot1

Memory Slot2

Graphics Intel® HD Graphics 4600

HDD Seagate ST320LT012 320GB

Intel GHz)

InnoDisk M3U0-8GSSALPC-AC56 8GB DDR3 1600 LV DIMM

Monitor Acer G246HL

Power Supply FSP350-60PFG

Cooler Delta FHSA9025B-1225 Video

Resolution BIOS 0.92

Item

Introduction 11

1024 x 768 x32bit

BIOS EIST/C-state Enabled

Current (A)/ Voltage (V)

Power (W)

BIOS EIST/C-state Disabled

Current (A)/ Voltage (V)

Power (W)

System Configurations

0.64/5.01

S4 0.10/5.04 0.504 0.11/5.04 0.5544

S5 0.08/5.04 0.4032 0.08/5.04 0.4032

Windows 7 (Idle)

Windows 7 (Typical)

Windows 7 (Max loading)

0.81/12.07

0.81/3.31

0.73/4.97

0.56/12.07

0.82/3.30

1.14/5.00

3.22/12.08

0.83/3.30

0.79/5.00

4.67/12.08

0.79/3.30

15.6642

13.0933

47.3366

62.9706

0.66/5.01

0.84/12.07

0.82/3.31

0.58/4.97

0.76/12.07

0.81/3.30

1.03/5.00

2.34/12.08

0.84/3.30

0.82/5.00

4.55/12.08

0.79/3.30

16.1596

14.7288

36.1892

61.671

1.8.4 Intel® Celeron® G1820 Processor 2.7GHz (53W)

System Configurations

CPU

Memory Slot1

Memory Slot2 Graphics Intel® HD Graphics

HDD Seagate ST320LT012 320GB Monitor Acer G246HL Power Supply FSP350-60PFG Cooler Delta FHSA9025B-1225 Video

Resolution BIOS 0.92

Intel® Celeron® Processor G1820 (2M Cache,

2.70 GHz) InnoDisk M3U0-8GSSALPC-AC56 8GB DDR3

1600 LV DIMM InnoDisk M3U0-8GSSALPC-AC56 8GB DDR3

1600 LV DIMM

1024 x 768 x32bit

12 Introduction

System Configurations

Item

BIOS EIST/C-state Enabled

Current (A)/ Voltage (V)

Power (W)

0.63/5.00

0.85/12.07

16.0575

0.80/3.31

BIOS EIST/C-state Disabled

Current (A)/ Voltage (V)

Power (W)

0.61/5.00

0.85/12.07

15.9575

0.80/3.31 S4 0.10/5.03 0.503 0.10/5.04 0.503 S5 0.05/4.96 0.248 0.06/4.96 0.2976

Windows 7 (Idle)

Windows 7 (Typical)

Windows 7 (Max loading)

0.73/5.00

0.59/12.11

0.79/3.31

1.12/4.99

1.90/12.07

0.80/3.30

0.81/5.00

3.62/12.02

0.80/3.30

13.4098

31.1618

50.2024

0.72/5.02

0.59/12.01

0.81/3.30

1.07/5.02

1.75/12.01

0.40/3.30

0.78/5.00

3.48/12.02

0.81/3.30

13.3589

27.7089

48.4026

NuPRO-E72

1.9 Rear I/O Panel

1 2 3

Figure 1-3: Rear I/O Panel

Connector Description

1 LAN1 port (RJ-45) Gigabit Ethernet (supports Intel® AMT) 2 LAN2 port (RJ-45) Gigabit Ethernet 3 VGA port DB-15 connector for CRT or LCD monitor 4 USB 3.0 ports SuperSpeed USB 3.0 ports

Introduction 13

USB 3.0 Connectors

LAN (RJ-45) Ports

Pin # Signal Name

1 USB3.0_P5VA 2 USB2_CMAN 3 USB2_CMAP 4GND 5 USB3A_CMRXN 6 USB3A_CMRXP 7GND 8 USB3A_CMTXN 9 USB3A_CMTXP

10BASE-T/

100BASE-TX

1000BASE-T

LED1

LED2

Pin #

1 TX+ BI_DA+ 2 TX- BI_DA3 RX+ BI_DB+ 4 -- BI_DC+ 5 -- BI_DC6 RX- BI_DB7 -- BI_DD+ 8 -- BI_DD-

Refer to the table below for the LAN port LED definitions.

LED1 LED2

Status Description Status Description

Off No Link Off 10 Mb connection On Linked Green 100 Mb connection

Blinking Data Activity Amber 1 Gb connection

14 Introduction

VGA Port

NuPRO-E72

Pin # Signal Pin # Signal

1 Red 9 +5 V 2 Green 10 Ground 3Blue11NC 4 NC 12 DDC DAT 5 Ground 13 HSYNC 6 Ground 14 VSYNC 7 Ground 15 DDC CLK 8 Ground

Introduction 15

1.10 Board Layout

5 6

8 9 10 11 12 13

Figure 1-4: NuPRO -E72 Board Topography

Connector Description

1 CN24 ATX 12V Power connector 2 CN28/29 DDR3 ECC DIMM slots 3 CN45 System Panel pin header 4 FAN1 CPU fan connector 5 CN30/32 SATA 6 Gb/s connectors 6 CN31/33 SATA 6 Gb/s connectors 7 CN16 COM6 connector 8 CN14 COM5 connector

9 CN13 COM4 connector 10 CN12 COM3 connector 1 1 CN17 DVI-D pin header 12 CN23 COM1 connector 13 CN11 COM2 connector 14 CN36/37 USB 3.0 pin headers 15 CN40 HD Audio Daughter Board pin header 16 JBAT2 Clear RTC 17 JBAT 1 Clear CMOS 18 CN27 PS/2 Keyboard/Mouse pin header 19 FAN2 System fan connector

20 SW13

COM1 mode switch (on solder side, near the rear I/O USB 3.0 connectors)

16 Introduction

NuPRO-E72

1.11 Onboard Connectors

COM1~6 Connector (RS-232) (CN11~14/16/23)

Pin # RS-232 Signal

1 DCD 2DSR 3RXD

910

COM1 COM2 COM3 COM4 COM5 COM6

Connector CN23 CN16 CN11 CN12 CN13 CN14

Pitch 2.54 mm 2.54 mm 2.00 mm 2.00 mm 2.00 mm 2.00 mm

4RTS 5TXD 6CTS 7DTR 8RI 9GND

10 NC

COM1 Connector (RS-422/485) (CN23)

Pin # RS-422 RS-485

1 TXD- Data2NC NC 3 TXD+ Data+

910

Introduction 17

4NC NC 5RXD+ NC 6NC NC 7RXD- NC 8NC NC 9GND GND

10 NC NC

USB 3.0 Connectors (CN36/37)

Pin # Signal Pin # Signal

1 P5V_USB3B 20 NC 2 S_USB3_RN3_R 19 P5V_USB3B 3 S_USB3_RP3_R 18 S_USB3_RN4_R 4 GND 17 S_USB3_RP4_R 5 S_USB3_TN3_R 16 GND 6 S_USB3_TP3_R 15 S_USB3_TN4_R 7 GND 14 S_USB3_TP4_R

8 S_USB2_N2_R 13 GND

9 S_USB2_P2_R 12 S_USB2_N3_R

10 S_USB_OC1# 11 S_USB2_P3_R

DVI-D Onboard Connector(CN17)

Pin # Signal Pin # Signal

1 GND 2 GND

3 DVI-Clock+ 4 DVI-Data05 DVI-Clock- 6 DVI-Data0+ 7 GND 8 GND 9 DVI-I2C-Clock 10 DVI-Data1-

11 DVI-I2C-Data 12 DVI-Data1+ 13 GND 14 GND 15 DVI-HPD 16 DVI-Data217 +5V 18 DVI-Data2+ 19 GND 20 GND

18 Introduction

DVI-D Bracket Connector

(optional cable w/ bracket, P/N 30-01052-2000)

Pin # Signal Pin # Signal

1 TMDS Data2- 13 TMDS Data3+ 2 TMDS Data2+ 14 +5 V Power 3 TMDS Data2/4 Shield 15 GND 4 TMDS Data4- 16 Hot Plug Detect 5 TMDS Data4+ 17 TMDS Data06 DDC Clock [SCL] 18 TMDSData0+ 7 DDC Data [SDA] 19 TMDS Data0/5 Shield 8 Analog vertical sync 20 TMDS Data5-

9 TMDS Data1- 21 TMDS Data5+ 10 TMDS Data1+ 22 TMDS Clock Shield 11 TMDS Data1/3 Shield 23 TMDS Clock + 12 TMDS Data3- 24 TMDS Clock -

NuPRO-E72

ATX 12V Power Connector (CN24)

Pin # Signal

2 4

1 3

1GND 2GND 3+12V DC 4

+12V DC

PS/2 Keyboard/Mouse Pin Header (CN27)

Introduction 19

Pin # Signal Pin # Signal

1 KBDATA 2 KBCLK 3 MSDATA 4 MSCLK 5 KM_VCC 6 GND

Serial ATA Connectors (CN30~33)

Pin # Signal

1GND

2TXP 3TXN 4GND

5RXN 6RXP 7GND

HD Audio Daughter Board Connector (CN40)

This connector is designed for use with the ADLINK DB-Audio2 daughter board.

Pin # Signal Function

1 GND Ground 2 AUD_BCLK Audio Clock 3 GND Ground

910

4 ICH_AUD_SDIN1 Audio Data Input 5 P5V + 5V 6 ICH_AUD_SDOUT Audio Data Output 7 P5V_AUD + 5V 8 P3V3_DVDD 3.3V 9 AUD_SYNC Audio Synchronous

10 AUD_RSTJ Audio Reset

20 Introduction

System Panel Connector (CN45)

Connects to chassis-mounted buttons, speakers, and LEDs.

Pin # Signal Function Pin Group

1 WDSPK Speaker signal

10 20

2NC 3NC 4+5V Power 5NC 6 GND Ground

7 KEYLOCK Keyboard lock 8 PLED Power LED signal 9NC

10 +5V Power LED pull-up

11 GND Ground 12 RESETBT RESET signal 13 NC 14 GND Ground 15 POWERBT Power-on signal 16 NC 17 NC 18 HDDLED Hard Disk LED signal 19 +3.3V Hard Disk LED pull-up 20 NC

Chassis Speaker

Power LED

Reset Button

Power Button

NuPRO-E72

Key Lock

HDD LED

Fan Connectors (FAN1/2)

Pin # Signal

1GND

Introduction 21

2 Fan power (+12V) 3 Fan Tachometer

Fan Speed Control

This page intentionally left blank.

22 Introduction

2 Getting Started

2.1 Package Contents

Before unpacking, check the shipping carton for an y damage. If the shipping carton and/or contents are damaged, inform your dealer immediately. Retain the shipping carton and packing materials for inspection. Obtain authorization from the dealer before returning any product to ADLINK.

X NuPRO-E72 X SATA data cable with latch x2 X 2-port USB 3.0 cable with bracket X 2-port COM cable with bracket for COM1/COM2

(2.54 mm pitch)

X 2-port COM cable with bracket x2 for COM3-6

(2.0 mm pitch)

X Driver DVD X User’s manual

NuPRO-E72

The NuPRO-E72 must be protected from static discharge and physical shock. Never remove any of the socketed parts except

WARNING:

at a static-free workstation. Use the anti-static bag shipped with the product to handle the board. Wear a grounded wrist strap when installing and/or servicing.

2.2 Installing the CPU

The NuPRO-E 72 supports an Intel® Core™ i7/i5/ i3 or Pentium processor in an LGA1150 socket.

X Disconnect all power to the board before install-

ing a CPU to prevent damaging the board and

WARNING:

Getting Started 23

CPU.

X Do not touch socket con tacts. Damaging the

contacts voids the product warranty. Follow the installation instructions carefully to avoid damaging the board components.

To install the CPU:

1. Press down on the locking arm (A), then push it aw ay from the socket to disengage it from the retention tab (B).

2. Raise the locking arm to unlock the load plate.

3. Lift the load plate to uncover the socket.

4. Remove the plastic protective cover from the socket. Note the locations of the alignment keys (A) and Pin 1

24 Getting Started

NuPRO-E72

indicator (B).

Do not touch socket contacts.

WARNING:

5. Hold the CPU using thumb and forefinger as shown.

Position the CPU over the socket, matching the notches on the sides of the CPU with the alignment keys on the socket (A). The golden triangle on the CPU must be positioned at the corner of the socket with the Pin 1 indicator as shown (B).

The CPU fits into the socket in only one orientation. Do not force it into the socket to avoid causing damage.

WARNING:

Getting Started 25

Carefully place the CPU into the socket vertically. The socket has cutouts for your fingers to fit into.

Cutouts

6. Gently lower the load plate. Make sure the front edge of the plate is under the screw as indicated.

7. Lower the locking arm and fasten it to the retention tab (A). The load plate should be locked underneath the screw as shown (B).

26 Getting Started

NuPRO-E72

2.3 Installing the CPU Fan and Heatsink

The CPU requires a chassis with an airflow inlet and maximum internal ambient temperature of 50° C. A especially-designed

CAUTION:

When the CPU fan installation procedures presented here are inconsistent with the installation procedures you obtained from the CPU fan and heatsink package, follow the latter.

To install the CPU fan:

CPU fan and heatsink must be installed before using the SHB. Failure to install a CPU fan and heatsink may damage the system host board and/or the CPU.

1. Apply thermal grease evenly on top of the inst alled CPU.

2. Lower the CPU fan to the CPU, then secure it using the

provided attachments or screws.

3. Connect the CPU f an cable to the CPU fan connector on

the SHB labeled FAN2 (See “Board Layout” on page 16.).

2.4 Installing Memory Modules

The NuPRO-E72 supports up to 16 GB of DDR3 ECC 1333/1600 MHz memory modules in two DIMM sockets. A DDR3 ECC module has a 240-pin footprint compared to the legacy 184-pin DDR DIMM. DDR3 ECC modules are notched to facilitate correct installation in the DIMM sockets.

Disconnect all power to the board before installing a memory module to prevent damaging the board and memory module.

WARNING:

Getting Started 27

Memory Configuration Options

The NuPRO-E72 supports 1GB, 2GB, 4GB and 8GB unbuffered DDR3 ECC DIMMs in the following configurations:

X Channel A: DIMM1

Channel B: DIMM2

X For dual-channel configuration, the total size of memory

module installed per channel must be the same (DIMM1 = DIMM2).

X It is recommended that you install DIMMs with the same

CAS latency. For maximum compatibility, install memory modules with the same brand, model, and/or rating.

To install a memory module:

1. Locate the DIMM sockets on the motherboard.

2. Press the socket’s retaining clips outward to unlock.

3. Align the memory module on the socket making sure that the notch matches the break on the socket.

28 Getting Started

NuPRO-E72

Notch

Break

4. Insert the module firmly into the slot until the retaining

clips snap back inwards and the module is securely seated.

2.5 Jumpers & Switches

Clear CMOS Jumper (JBAT1)

To clear the BIOS settings (RTCRTS# asserts):

1. Power down and disconnect power from the system.

2. Short pins 2-3 on JP1.

3. Reconnect power and power up the system.

4. Wait 3 seconds or more.

5. Power down and disconnect power from the system.

Getting Started 29

6. Re-short pins 1-2, and power up the system..

CMOS Status Connection JBAT1

Normal 1 – 2

Clear CMOS 2 – 3

Clear RTC Jumper (JBAT2)

To clear the BIOS settings and data/time (SRTCRST# and RTCRST# assert):

1. Power down and disconnect power from the system.

2. Short pins 2-3 on JP1.

3. Reconnect power and power up the system.

After power up, remove the jumper cap from pins 2-3 and reinstall it to pins 1-2.

CMOS Status Connection JBAT2

Normal 1 – 2

Clear CMOS 2 – 3

To clear CMOS, clear both CMOS and RTC jumpers at the same time.

30 Getting Started

COM1 Mode Switch (SW13)

NuPRO-E72

1 2

DIP #1 DIP #2 COM1 Mode

On Off RS-232 On On RS-422 Off On RS-485

2.6 Driver Installation

This chapter provides information on how to install the NuPROE72 device drivers under Windows 7 64-bit. The device drivers are located in the following ADLINK All-in-One DVD directories:

Chipset \NuPRO\NuPRO-E72\Chipset\ Display \NuPRO\NuPRO-E72\VGA\ Ethernet \NuPRO\NuPRO-E72\Ethernet\ Rapid Storage \NuPRO\NuPRO-E72\Others\RST\ USB 3.0 \NuPRO\NuPRO-E72\Others\ Management

Engine

Install the Windows operating system before installing any driver. Most standard I/O device drivers are installed during Windows installation.

\NuPRO\NuPRO-E72\Others\ME_Driver\

In order to enable RAID or AHCI mode, you must pre-install the Intel® Rapid Storage Technology driver during the Windows*

NOTE:

installation process. using the F6 installation method. *Not required for Windows Vista and Windows 7.

Getting Started 31

2.6.1 Installing Chipset Driver

To install the Intel® C226 Express chipset driver, locate the directory X:\NuPRO\NuPRO-E72\Chipset\ on the ADLINK All-inOne DVD, run the program infinst_autol.exe and follow the onscreen instructions. Restart the system if prompted.

2.6.2 Installing Graphics Driver

To install the Integrated Intel® HD graphics driver:

1. Locate the directory X:\NuPRO\NuPRO-E72\VGA\64 Bit\ on the ADLINK All-in-One DVD, and extract the contents of the following archive: Win64.zip

2. Run the program setup.exe and follow the onscreen instructions. Restart the system if prompted.

2.6.3 Installing Ethernet Driver

To install the Ethernet driver, locate the directory X:\NuPRO\NuPRO-E72\Ethernet\Windows\64\ on the ADLINK All-in-One DVD, run the program PROWinx64.exe and follow the onscreen instructions. Restart the system if prompted.

2.6.4 Installing Management Engine Driver

To install the Management Engine driver:

1. Locate the directory X:\NuPRO\NuPRO-E72\Others\ME_Driver\ on the ADLINK All-in-One DVD, and extract all files from the following archive: ME90.zip.

2. Run the program setup.exe and follow the onscreen instructions. Restart the system if prompted.

2.6.5 Installing USB 3.0 Driver

To install the USB 3.0 driver.

1. Locate the directory X:\NuPRO\NuPRO-E72\USB3\ on the ADLINK All-inOne DVD, and extract all files from the following archive: USB3.zip.

32 Getting Started

2. Run the program setup.exe and follow the onscreen

instructions. Restart the system if prompted.

NuPRO-E72

Getting Started 33

This page intentionally left blank.

34 Getting Started

Appendix A BIOS Setup

The following chapter describes basic navigation for the AMIBIOS® EFI BIOS setup utility.

A.1 Starting the BIOS

To enter the setup screen, follow these steps:

1. Power on the motherboard

2. Press the < Delete > key on your keyboard when you

see the following text prompt: < Press DEL to run Setup >

3. After you press the < Delete > key, the main BIOS setup

menu displays. You can access the other setup screens from the main BIOS setup menu , such as Chipset and Power menus.

NuPRO-E72

Note: In most cases, the < Delete > key is used to invoke the setup

screen. There are several cases that use other keys, such as < F1 >, < F2 >, and so on.

Setup Menu

The main BIOS setup menu is the first screen that you can navigate. Each main BIOS setup menu option is described in this user’s guide.

The Main BIOS setup menu screen has two main frames. The left frame displays all the options that can be configured. “Grayed” options cannot be configured, “Blue” options can be.

The right frame displays the key legend. Above the key legend is an area reserved for a text message. When an option is selected in the left frame, it is highlighted in white. Often a text message will accompany it.

Navigation

The BIOS setup/utility uses a key-based navigation system called hot keys. Most of the BIOS setup utility hot keys can be used at any time during the setup navigation process.

These keys include < F1 >, < F10 >, < Enter >, < ESC >, < Arrow > keys, and so on. .

NuPRO-E72

Note: There is a hot key legend located in the r ight frame on most

setup screens.

The < F8 > key on your keyboard is the Fail-Safe key. It is not displayed on the key legend by default. To set the Fail-Safe settings of the BIOS, press the < F8 > key on your keyboard. It is located on the upper row of a standard 101 keyboard. The Fail-Safe settings allow the motherboard to boot up with the least amount of options set. This can lessen the probability of conflicting settings.

Hotkey Descriptions

F1 The < F1 > key allows you to display the General Help

screen. Press the < F1 > key to open the General Help screen.

F10 The < F10 > key allows you to save any changes you have

made and exit Setup. Press the < F10 > key to save your changes. The following screen will appear:

Press the < Enter > key to save the configuration and exit. You can also use the < Arrow > key to select Cancel and then press the < Enter > key to abort this functio n and return to the previous screen.

ESC The < Esc > key allows you to discard any changes you have

made and exit the Setup. Press the < Esc > key to exit the setup without saving your changes. The following screen will appear:

Press the < Enter > key to discard changes and exit. You can also use the < Arrow > key to select Cancel and then press the < Enter > key to abort this function and return to the previous screen.

Enter The < Enter > key allows you to display or change the setup

option listed for a particular setup item. The < Enter > key

NuPRO-E72

can also allow you to display the setup sub-screens.

A.2 Main Setup

When you first enter the Setup Utility, you will enter the Main setup screen. You can always return to the Main setup screen by selecting the Main tab. There are two Main Setup options. They are described in this section. The Main BIOS Setup screen is shown below.

System & Board Info

BIOS Vendor

Displays the BIOS vendor.

Core Version

Displays the BIOS core version.

Compliancy

Displays the current BIOS compliancy.

Project Version

Displays the current BIOS revision.

Build Date and Time

Displays the BIOS build data.

System Time/System Date

Use this option to change the system time and date. Highlight System Time or System Date using the < Arrow > keys. Enter new values using the keyboard. Press the < Tab > key or the < Arrow > keys to move between fields. The date must be entered in MM/ DD/YY format. The time is entered in HH:MM:SS format.

Note: The time is in 24-hour format. For example, 5:30 A.M. ap-

pears as 05:30:00, and 5:30 P.M. as 17:30:00.

Access Level

Displays the current system access level.

A.3 Advanced BIOS Setup

Select the Advanced tab from the setup screen to enter the Advanced BIOS Setup screen. You can select any of the items in the left frame of the screen, such as SuperIO Configuration, to go to the sub menu for that item. You can display an Advanced BIOS Setup option by highlighting it using the < Arrow > keys. The Advanced BIOS Setup screen is shown below.

The sub menus are described on the following pages.

Launch PXE OpROM

Boot Option for Legacy Network Devices. Options: Enabled/ Disabled.

NuPRO-E72

A.3.1 ACPI Settings

Enable APIC Auto Configuration

BIOS ACPI Auto Configuration. Options: Enabled/Disabled.

Enable Hibernation

Enable or disable the system's ability to hibernate (S4 sleep state). This option may be not effective with some OS's.

ACPI Sleep State

Select the highest ACPI sleep state the system will enter, when the SUSPEND button is pressed. Options: S1, S3, Suspend Disable.

AC Power Shutdown

ATX mode: OS will turn off system power when shutdown. AT mode: OS show It is now safe to turn off your computer.

AT mode will not support S3 & S4.

NOTE:

Lock Legacy Resources

Enable or disable Lock of Legacy Resources.

NuPRO-E72

A.3.2 Trusted Computing

Trusted computing is an industry standard to make personal computers more secure through a dedicated hardware chip, called a Trusted Platform Module (TPM).

TPM Support

This option enables or disables the TPM support. System reset is required. Options: Enabled/Disabled.

TPM State

Determine whether TPM state change requires Password Authentication. Options: Enabled/Disabled.

Pending TPM Operation

Scheduled TPM operation. The settings for this value are Enable, Disable and Clear.

A.3.3 CPU Configuration

Active Processor Cores

Number of cores to enable in processor. Options: All, 1, 2.

Limit CPUID Value Maximum

When Enabled, the processor will limit the maximum CPUID input value to 03h when queried, even if the processor supports a higher CPUID input value. When Disabled, the processor will return the actual maximum CPUID input value of the processor when queried. Enable this option to allow compatibility with older operating systems.

Execute Disable Bit

Allows you to enable or disable the No-Execution Page Protection Technology. Setting this item to [Disabled] forces the XD feature flag to always return a z ero (0). Option s: Enabled, Disabled.

Intel® Virtualization Tech

When enabled, Intel® Virtualization Technology (Intel® VT) makes a single system appear as multiple independent sys-

NuPRO-E72

tems to software. This allows for multiple, independent operating systems to be running simultaneously on a single system.

Power Technology

Sets the power management features. Options: Disable, Energy Efficient, Custom.

Socket 0 CPU Information

A.3.4 SATA Configuration

SATA Mode

Options: IDE, RAID, AHCI.

Serial ATA Controller 0/1

Appears when SATA mode is set to IDE. This item specifies whether Serial ATA Controller 0/1 is initialized in Compatible or Enhanced mode of operation. The settings are Disabled, Compatible and Enhanced.

Aggressive Link Power Management

Appears when SA TA mode is set to AHCI. The setting s are Disabled and Enabled.

SATA Port 0~5 The Staggered Spin-up, External SATA Port (eSATA) and

Hot Plug options appear when SATA Mode is set to AHCI.

Options: Enabled/Disabled.

NuPRO-E72

A.3.5 Intel TXT Configuration

Intel Trusted Execution Technology (Int el TXT) support can only be enabled when TPM is enabled, if the CPU supp orts Safer Mode Extensions (SMX), and Intel® Virtualization Technology (Intel® VT) and Intel® Virtualization Technology for Directed I/O (VT-d) are enabled.

A.3.6 Intel IGD SWSCI OpRegion

DVMT Mode

This item allows the user to enable or disable the DVMT function.

DVMT/Fixed Memory

Select DVMT/Fixed memory size used by the Integrated Graphics Device. Options: 128MB, 256MB, Maximum.

IGD - Boot Type

Select the video device which will be activated during POST. This has no effect if an external graphics device is present. Options: CRT+DVI, CRT, DVI.

Spread Spectrum Clock

IGD device spread spectrum clock function. Options: Enabled/ Disabled.

A.3.7 USB Configuration

Legacy USB Support

Legacy USB Support refers to USB mouse and keyboard support. Normally if this option is not enabled, any attached USB mouse or USB keyboard will not become available until a USB compatible operating system is fully booted with all USB drivers loaded. When this option is enabled, any attached USB mouse or USB keyboard can control the system even when there are no USB drivers loaded on the system. Set this value to enable or disable the Legacy USB Support.

X Disabled: Set this value to prevent the use of any USB

device in DOS or during system boot.

X Enabled: Set this value to allow the use of USB devices

during boot and while using DOS.

X Auto: This option auto de tects USB Keyboards or Mi ce and

if found, allows them to be utilized during boot and while using DOS.

USB 3.0 Support

USB 3.0 Controller support. Options: Enable, Disable.

NuPRO-E72

XHCI Hand-Off

This is a workaround for OSes without XHCI hand-off support. The XHCI ownership change should be claimed by XHCI driver. Options: En able, Disable.

EHCI Hand-Off

This is a workaround for OSes without EHCI hand-off support. The EHCI ownership change should be claimed by EHCI driver. Options: En able, Disable.

All USB Devices

Enabled/Disabled All USB devices. Options: Enable, Disable.

EHCI Controller 1/2

Enabled/Disabled USB 2.0 (EHCI) Support. Options: Enable, Disable.

USB Port 0~13

Enabled/Disabled USB Port 0~13. Options: Enable, Disable.

Mass Storage Devices:

Mass storage device emulation type. 'AUTO' enumerates devices according to their media format. Optical drives are emulated as 'CDROM', drives with no media will be emulated according to a drive type. Options: Auto, Floppy, Forced FDD, Hard Disk, CD-ROM.

A.3.8 Super IO Configuration

Serial Port1-6 Configuration

Enter the submenu for each serial port to enable/disable and view the I/O port and IRQ settings.

Parallel Port Configuration

NuPRO-E72

Enter the submenu to enable/disable the parallel port and specify the base I/O port address.

A.3.9 Hardware Monitor

You can use this screen to view System Status information and to select options for FAN1 settings (FAN2

Smart Fan 1 Mode Setting Three operating modes are provided for FAN1: Full Mode, Auto-

matic Mode, and Manual Mode. Full Mode runs the fan at full

speed. Automatic Mode is Smart Fan mode. Manual Mode runs the fan at the set speed (minimum is 0, maximum is 127).

Automatic Mode

In Automatic Mode, the following settings are visible.

is set to Full On by default

Fan Off Temperature Limit

Sets the temperature below which the fan will turn off in degrees Celsius (°C). When the temperature is higher than the set value, FAN1 will run at Fan Start PWM speed. When the temperature is lower than the set value, FAN1 will stop.

Fan Start Temperature Limit

When the temperature in degrees (°C) is higher than the set value, FAN1 will increase its speed according to the PWM Slope Setting value.

Fan Start PWM Sets the PWM value of the fan between Fan Off Temperature

Limit and Fan Start Temperature Limit. Minimum value is 0

and maximum is 127.

PWMSlope Setting

The Slope PWM Value sets the rate of increase the fan speed when the temperature is above Fan Start Temperature Limit.

System Status

System temperature, CPU temperature and fan speed (FAN1), system voltages.

A.3.10 AMT Configuration

NuPRO-E72

AMT

This item allows the user to Enable/Disable the Intel AMT function.

Unconfigure AMT/ME

This item allows the user to unprovision the AM T/ME function without a password.

Wat ch Dog Timer

Options: Enabled/Disabled.

OS WatchDog Timer

Sets the OS WatchDog Timer (seconds).

BIOS WatchDog Timer

Sets the BIOS WatchDog Timer (seconds).

A.3.11 Serial Port Console Redirection

COM0/1 Console Redirection

Options: Enabled/Disabled.

Console Redirection Settings

The settings specify how the host computer and the remote computer exchange data. Both computers should have the same or compatible settings.

NuPRO-E72

Terminal Type

This option is used to select either VT100/VT-UTF8 or ANSI terminal type. Options: VT100, VT100+, VT-UTF8, ANSI.

Bits per second

Select the bits per second you want the serial port to use for console redirection. The options are 115200, 57600, 38400, 19200, 9600.

Data Bits

Select the data bits you want the serial port to use for console redirection. Set this value to 7 and 8.

Parity

Set this option to select Parity for console redirection. The settings for this value are None, Even, Odd, Mark and Space.

Stop B its

Stop bits indicate the end of a serial data packet. (A start bit indicates the beginning). The standard setting is 1 stop bit. Communication with slow devices may require more than 1 stop bit. Set this value to 1 and 2.

Flow Control

Set this option to select Flow Control for console redirection. The settings for this value are None, Hardware RTS/CTS.

Record Mode

With this mode enabled only text will be sent., allowing capture of Terminal data. Set this value to Enabled or Disabled.

Resolution 100x31

Enable or disable extended terminal resolution. Set this value to Enabled or Disabled.

Legacy OS Redirection Resolution

On a legacy OS, the number of Rows and Columns supported by redirection. Set this value to 80x24 and 80x25.

NuPRO-E72

Serial Port for Out-of-Band Management

These settings control the ACPI serial port redirection table (SPCR) which is used by Windows servers to provide Windows Emergency Management Services (EMS) and is independent from console redirection output. OoB Management or EMS allows the remote management of selected components of Windows servers, even when a server is not connected to the network or the network is not available

Terminal Type

VT-UTF8 is the preferred terminal type for out-of-band management. The next best choice is VT100+ and then VT100. See above, in Console Redirection Settings page, for more Help with Terminal Type/Emulation. Options: VT100, VT100+,

VT-UTF8, ASNI. Bits per second

Select the bits per second you want the serial port to use fo r console redirection. The options are 115200, 57600, 38400, 19200, 9600.

Flow Control

Set this option to select Flow Control for console redirection. The settings for this value are None, Hardware RTS/CTS.

Data Bits

Displays the frame width for Out-of-Band Management.

Parity

Displays the parity for Out-of-Band Management.

Stop B its

Displays the number of stop bits for Out-of-Band Management.

A.4 Chipset Setup

Select the Chipset tab from the setup screen to enter the Chipset BIOS Setup screen. You can select any of the items in the left frame of the screen to go to the sub menu for that item. The Chipset BIOS Setup screen is shown below.

NuPRO-E72

A.4.1 Graphics and Memory Bridge Configuration

VT-d

Intel Virtualization Technology for Directed I/O. Options: Enabled/ Disabled.

Initial Graphics Adapter

Allows you to select which graphics controller to use as the primary boot device. Options: IGD, PCI/IGD, PCI/PEG, PEG/IGD, PEG/PCI.

IGD Memory

IGD shared memory size, Options: Disable/32M/64M/128M.

IGD Multi-Monitor

Multi-monitor support by the Internal Graphics Device. Options: Enabled/Disabled

PCI Express Port

This option enables auto negotiation with a PEG device, disables the use of the PEG port, or select enables use of the PEG port

A.4.2 PCH Bridge Configuration

82574L LAN Controller

Controls the onboard Intel 82574L LAN controller. Options: Enabled/Disabled.

Restore on AC Power Loss

Determines which state the computer enters when AC power is restored after a power loss. The options for this value are Last State, Power On and Power Off.

X Power Off: Set this value to always power off the system

while AC power is restored.

X Power On: Set this value to always power on the system

while AC power is restored.

X Last State: Set this value to power off/on the system depend-

ing on the last system power state while AC power is restored.

ALC626 HD Audio

Set this value to Enable/Disable the HD Audio Controller.

NuPRO-E72

PCI Express Port Configuration

PCI Express Port 1~8

Configures the PCI Express ports in of the chipset. Options: Auto, Enable, Disable.

PCIe Sub Decode

Enable or disable the PCIe Sub Decode port. This option is available when the Subtractive Decode Ag ent is enable (P CHTrap9[14]) = '1b'.

PCIE Ports 0-3 Configuration

Use this option to configure PCIe ports 0-3 of the PCH to "One x4 Port" or "Four x1 Ports".

NOTE:

The PCIE Ports 0-3 Configuration option is available in BIOS version A1.6 and later.

A.4.3 Management Engine Subsystem

ME Subsystem

Options: Enabled/Disabled.

ME Temporary Disable

Options: Enabled/Disabled (reset required).

End of POST Message

Options: Enabled/Disabled.

Execute MEBx

Options: Enabled/Disabled.

MEBx Mode

Options: Normal, Hidden Ctrl+P, Enter MEBx setup.

Integrated Clock Chip Configuration

ICC Enable

Integrated Clock Chip. Options: Enabled/Disabled.

NuPRO-E72

A.5 Boot Configuration

Select the Boot tab from the setup screen to enter the Boot BIOS Setup screen. You can select any of the items in the left frame of the screen, such as Boot Device Priority, to go to the sub menu for that item. You can display a Boo t BIOS setup option b y highlighting it using the < Arrow > keys. The Boot Configuration screen is shown below:

Setup Prompt Timeout

Number of seconds to wait for setup activation. 65535 (0xFFFF) means wait indefinitely.

Bootup NumLock State

This setting determines the state of the NumLock function on bootup. Options: On, Off.

Quiet Boot

When this feature is enabled, the BIOS will display the fullscreen logo during the boot-up sequence, hiding normal POST messages.

NuPRO-E72

When it is disabled, the BIOS will display the normal POST messages, instead of the full-screen logo.

Gate A20 Active

Options: Upon Request, Always.

Boot Option Priorities

Set the boot device options to determine the sequence in which the computer checks which device to boot from.

Hard Drive BBS Priorities

The Boot devices are listed in groups by device type. First press <Enter> to enter the sub-menu. You may then use the arrow keys to select the desired device, then press <+>, <-> or <PageUp>, <PageDown> key to move it up/down in the priority list. For example, USB storage disks will be listed as "USB Drives" in the sub-menu. Only the first device in each device gr

A.6 Security Setup

Password Support

Two Levels of Password Protection

Provides both a Supervisor and a User password. If you use both passwords, the Supervisor password must be set first.

The system can be configured so that all users must enter a password every time the system boots or when Setup is executed, using either or either the Supervisor password or User password.

The Supervisor and User passwords activate two different levels of password security. If you select password support, you are prompted for a one to six character password. Type the password on the keyboard. The password does not appear on the screen when typed. Make sure you write it down. If you forget it, you must drain NVRAM and re-configure.

Remember the Password

Keep a record of the new password when the password is changed. If you forget the password, you must erase the system configuration information in NVRAM.

To access the sub menu for the following ite m s, s ele ct th e item and press < Enter >:

X Change Administrator Password X Change User Password X Clear User Password

Administrator Password

Indicates whether a Administrator password has been set.

User Password

Indicates whether a user password has been set.

NuPRO-E72

A.7 Exit Menu

Select the Exit tab from the setup screen to enter the Exit BIOS Setup screen. You can display an Exit BIOS Setup option by highlighting it using the < Arrow > keys. The Exit BIOS Setup screen is shown below.

Save Changes and Exit

When you have completed the system configuration changes, select this option to leave Setup and reboot the computer so the new system configuration parameters can take effect.

Save Configuration Changes and Exit Now?

[Ok] [Cancel]

appears in the window. Select Ok to save changes and exit.

NuPRO-E72

Discard Changes and Exit

Select this option to quit Setup without making any permanent changes to the system configuration.

Discard Changes and Exit Setup Now?

[Ok] [Cancel]

appears in the window. Select Ok to discard changes and exit.

Save Changes and Reset

Reset the system after saving the changes.

Discard Changes and Reset

Reset system setup without saving any changes.

Save Changes

Save changes made so far to any of the setup options.

Discard Changes

Select Discard Changes from the Exit menu and press < Enter >. Select OK to discard changes.

Restore Defaults

Restore/Load Default values for all the setup options.

Save as User Defaults

Save the changes made so far as User Defaults.

Restore User Defaults

Restore the User Defaults to all the setup options.

Boot Override

This group of functions includes a list of devices within the boot order. Select a drive to immediately boot that device regardless of

the current boot order. If you are booting to the EFI Shell, an exit from the shell returns to Setup.

Appendix B - Watchdog Timer

A sample program for configuring the NuPRO-E72’s watchdog timer is included on the ADLINK All-in-One DVD in the following directory: \NuPRO\NuPRO-E72\WDT.

B.1 Sample Code

#include<stdio.h> #include<dos.h>

static unsigned int IT8783_ioPort = 0x2e;

void Enter_IT8783_Config(unsigned int flag) {

if(flag) IT8783_ioPort = 0x4e;

switch(IT8783_ioPort) {

case 0x2E: //Address port = 0x2E, enter keys = 0x87, 0x01, 0x55, 0x55

outportb(0x2E, 0x87); outportb(0x2E, 0x01); outportb(0x2E, 0x55); outportb(0x2E, 0x55);

break; case 0x4E: //Address port = 0x4E, enter keys = 0x87, 0x01, 0x55, 0xAA

outportb(0x4E, 0x87);

outportb(0x4E, 0x01);

outportb(0x4E, 0x55);

outportb(0x4E, 0xAA);

break; default:

break;

}

NuPRO-E72

void Exit_IT8783_Config(unsigned int flag) {

if(flag) IT8783_ioPort = 0x4e;

outportb(IT8783_ioPort, 0x02);

Watchdog Timer 71

outportb(IT8783_ioPort+1, 0x02);

}

void Get_IT8783_ID(unsigned int &ID1, unsigned int &ID2) {

outportb(IT8783_ioPort, 0x20); ID1 = inportb(IT8783_ioPort+1); outportb(IT8783_ioPort, 0x21); ID2 = inportb(IT8783_ioPort+1);

}

void IT8783_WDTRun(unsigned int count_value, unsigned int

PLEDflag) //for NuPRO-E72

{

unsigned long tempCount; unsigned int registerValue;

outportb(IT8783_ioPort, 0x07); outportb(IT8783_ioPort+1, 0x07);// Device 7

outportb(IT8783_ioPort, 0xf8); outportb(IT8783_ioPort+1, 0x00);// PLED mapping to

nothing, disable PLED function

if(PLEDflag == 1) {

outportb(IT8783_ioPort, 0x27); registerValue = inportb(IT8783_ioPort + 1); registerValue |= 0x80; // set Pin09 is GPIO function GP37 outportb(IT8783_ioPort+1, registerValue);

outportb(IT8783_ioPort, 0xc2); registerValue = inportb(IT8783_ioPort + 1); registerValue &= 0x7fb; // set GP37 is alternate function outportb(IT8783_ioPort+1, registerValue);

outportb(IT8783_ioPort, 0xca); registerValue = inportb(IT8783_ioPort + 1); registerValue |= 0x80; // set GP42 is output

72 Watchdog Timer

outportb(IT8783_ioPort+1, registerValue);

outportb(IT8783_ioPort, 0xf8); outportb(IT8783_ioPort+1, 0x1f);// PLED mapping to GP37

outportb(IT8783_ioPort, 0xf9); registerValue = inportb(IT8783_ioPort + 1); registerValue |= 0x02; registerValue &= 0xfb; outportb(IT8783_ioPort+1, registerValue);

}

outportb(IT8783_ioPort, 0x71); registerValue = inportb(IT8783_ioPort + 1); registerValue &= 0xfe; outportb(IT8783_ioPort+1, registerValue);

outportb(IT8783_ioPort, 0x72); registerValue = inportb(IT8783_ioPort + 1); registerValue &= 0xdf; outportb(IT8783_ioPort+1, registerValue);

if(count_value >= 60) {

outportb(IT8783_ioPort, 0x72); registerValue = inportb(IT8783_ioPort+1); registerValue &= 0x8f; registerValue |= 0x40; //enable WDT output through PRST outportb(IT8783_ioPort+1, registerValue); // set WDT count is minute

NuPRO-E72

tempCount = count_value / 60; if((count_value%60) > 30)

tempCount++; if(tempCount > 65535)

tempCount = 65535; printf("WDT timeout in %d minutes.\n", tempCount);

} else {

outportb(IT8783_ioPort, 0x72);

Watchdog Timer 73

registerValue = inportb(IT8783_ioPort+1); registerValue |= 0x80;

tempCount = count_value; if(tempCount != 0) {

printf("WDT timeout in %d seconds.\n",

tempCount);

registerValue |= 0x40; //Enable WDT output

through KBRST } else {

printf("WDT is Disabled.\n"); registerValue &= 0xbf; //Disable WDT output

through KBRST }

outportb(IT8783_ioPort+1, registerValue); // set WDT count is second

}

outportb(IT8783_ioPort, 0x71); registerValue = inportb(IT8783_ioPort + 1); registerValue |= 0x60; // set Mouse & Keyboard

interrupt Enable

outportb(IT8783_ioPort+1, registerValue);

outportb(IT8783_ioPort, 0x73); outportb(IT8783_ioPort+1, tempCount); // set WDT count

LSB

}

74 Watchdog Timer

Appendix C - System Resources

C.1 System Memory Map

NuPRO-E72

Address Range (decimal)

(4GB-2MB)

(4GB-18MB) – (4GB-17MB-1)

(4GB-20MB) – (4GB-19MB-1)

960 K – 1024 K F0000 – FFFFF 64 KB System BIOS Area

896 K – 960 K E0000 – EFFFF 64 KB Extended System BIOS Area

768 K – 896 K C0000 – DFFFF 128 KB

640 K – 768 K A0000 – BFFFF 128 KB Video Buffer & SMM space

0 K – 640 K 00000 – 9FFFF 640 KB DOS Area

Address Range (hex)

FFE00000 –

FFFFFFFF

FEE00000 –

FEEFFFFF

FEC00000 –

FECFFFFF

Table C-1: System Memory Map

Size Description

2 MB High BIOS Area

1 MB FSB Interrupt Memory Space

1 MB APIC Configuration Space

PCI expansion ROM area C0000 – C7FFF: Onboard VGA BIOS CB800 – CC7FFF: Intel 82577LM PXE option ROM when onboard LAN boot ROM is enabled.

C.2 Direct Memory Access Channels

Channel Number Data Width System Resource

08-bits

18-bits

28-bits

38-bits

4 Reserved - cascade channel

5 16-bits Open

6 16-bits Open

7 16-bits Open

Table C-2: Direct Memory Access Channels

Parallel port Parallel port

Diskette drive

Parallel port

(1) (1)

(1)

Note (1): DMA channel 0, 1, or 3 will be occupied when using the parallel port.

C.3 IO Map

Hex Range Device

000-01F DMA controller 1, 8237A-5 equivalent

020-02D and 030-03F Interrupt controller 1, 8259 equivalent

02E-02F,04E-04F LPC SIO (ITE8783) configuration index/data registers

040-042, 050-052 Timer, 8254-2 equivalent

060, 062, 064, 066 8742 equivalent (keyboard)

061 NMI control and status 070-077 Real Time Clock Controller (bit 7 -NMI mask) 080-091 DMA page register

092 Reset (Bit 0)/ Fast Gate A20 (Bit 1) 093-09F DMA page registers continued

0A0-0B1 and 0B4-

0BD

0C0-0DF DMA controller 2, 8237A-5 equivalent

0F0

2E0 - 2F7 Serial Port 6

2E8 – 2EF Serial Port 4

2F0 – 2F7 Serial Port 5

2F8 – 2FF Serial Port 2

170-177 and 1F0-1F7

376 and 3F6

378 - 37F Parallel port

3B0 – 3BB Mono/VGA mode video

3C0- 3DF VGA registers 3E8 – 3EF Serial Port 3 3F8 – 3FF Serial Port 1

4D0 and 4D1 Interrupt controller

400 – 47F SB PM Base Address 500 – 57F SB GPIO

A00 – A3F SIO PME Base Address

CF9 Reset Control register (8 bit I/O)

1180 – 119F SMBus

Interrupt controller 2, 8259 equivalent

Read: PCI and Master abort. (Note 1)

Write: FERR#/ IGNNE# /Interrupt controller

SATA controller or PCI

Table C-3: IO Map

NuPRO-E72

Note:

A read to this address will subtractively go to PCI, where it will master abort.

C.4 Interrupt Request (IRQ) Lines

IRQ Lines PIC Mode

Typical Interrupt

IRQ#

Resource

0 Counter 0 N/A No 1 Keyboard controller N/A No

Cascade interrupt from

3 Serial Port 2 (COM2)

5 PCI / ISA 6N/A N/A No 7 PCI / ISA 8 Real-time clock N/A No 9 SCI / PCI

10 PCI / ISA N/A No

11 PCI / ISA N/A No

12 PS/2 Mouse / PCI / ISA

13 Math Processor N/A No

15 PCI / ISA N/A No

slave PIC

Serial Port 1 (COM1) /

PCI / ISA

Primary IDE controller /

PCI / ISA

Table C-4: IRQ Lines PIC Mode

Connected to Pin Available

N/A No

IRQ3 via SERIRQ, IRQ3

at ISA bus

IRQ4 via SERIRQ, IRQ4

at ISA bus

IRQ5 via SERIRQ, IRQ5

at ISA bus

IRQ7 via SERIRQ, IRQ7

at ISA bus

IRQ9 via SERIRQ, IRQ9

at ISA bus

IRQ12 via SERIRQ,

IRQ12 at ISA bus

IRQ14 via SERIRQ,

IRQ14 at ISA bus

Note (1)

Note (1), (2)

Note (1)

Notes:

(1) These IRQs can be used for PCI devices when the onboard device is disabled. If the IRQ is from ISA, the user must reserve the IRQ for ISA in the BIOS setup menu.

(2) The BIOS does not open the IRQ 9 setting for the ISA bus.

IRQ Lines APIC Mode

Ty pi cal In terrupt

IRQ#

Resource

0 System Timer N/A No 1 Keyboard controller N/A No 2 PCI / ISA N/A No

Serial Port 2 (COM2) /

7 8 Real-time clock N/A No 9 ACPI-Compliant system

10 PCI / ISA

11 Serial Port 6 /PCI / ISA

12 PS/2 Mouse / PCI / ISA 13 Math Processor N/A No 14

16 N/A

17 N/A

PCI / ISA

Serial Port 1 (COM1) /

PCI / ISA

Serial Port 3 (COM3) /

PCI / ISA

Serial Port 4 (COM4) /

PCI / ISA

Parallel Port / Serial

5 (COM5) / PCI / ISA

Primary IDE controller /

PCI / ISA

Secondary IDE

controller / PCI / ISA

Connected to Pin Available

IRQ3 via SERIRQ,

IRQ3 at ISA bus

IRQ4 via SERIRQ,

IRQ4 at ISA bus

IRQ5 via SERIRQ,

IRQ5 at ISA bus

IRQ6 via SERIRQ No

Port

IRQ7 via SERIRQ,

IRQ7 at ISA bus

IRQ9 via SERIRQ,

IRQ9 at ISA bus

IRQ10 via SERIRQ,

IRQ10 at ISA bus

IRQ11 via SERIRQ,

IRQ11 at ISA bus

IRQ12 via SERIRQ,

IRQ12 at ISA bus

IRQ14 via SERIRQ,

IRQ14 at ISA bus

IRQ15 via SERIRQ,

IRQ15 at ISA bus

PCIE Port 0/1/2/3/4/5/6/7,

P.E.G. Root Port, I.G.D,

EHCI Controller #2,

MEI Controller.

PCIE Port 0/1/2/3/4/5/6/7,

P.E.G. Root Port, KT Controller

Note (1)

Note (1), (2)

Note (1)

Yes

T ypical Interrupt

IRQ#

Resource

18 N/A

19 N/A

20 N/A 21 N/A PCI Slot 0, PCI Slot 4 No

22 N/A PCH HDA, PCI Slot 1 No 23 N/A EHCI Controller #1, PCI Slot 2 No

Ta b le C-5: IRQ Lines AP IC Mode

Notes:

(1) These IRQs can be used for PCI devices when the onboard device is disabled. If the IRQ is from ISA, the user must reserve the IRQ for ISA in the BIOS setup menu.

(2) The BIOS does not open the IRQ 9 setting for the ISA bus.

Connected to Pin Available

PCIE Port 0/1/2/3/4/5/6/7, P.E.G. Root Port, SATA Host controller, SMBus Controller,

Thermal Controller,

SOL (COM7)

PCIE Port 0/1/2/3/4/5/6/7, P.E.G. Root Port, SATA Host

controller, SATA Host

controller#1,

PCH internal GBE controller,

PCI Slot 3

NuPRO-E72

Yes

PCI Configuration Space Map

Bus # Device # Function # Routing Description

00h 00h 00h N/A Intel Host Bridge

00 02H 00H Internal Intel IGD 02 00H 0FFH N/A P.E.G. Port

00h 02h 00h Internal

00h 16h 00h Internal

00h 16h 01h Internal 00h 16h 02h Internal IDE-R controller

00h 16h 03h Internal PCI Serial controller 00h 19h 00h Internal GbE Controller 00h 1Ah 00h Internal Intel USB EHCI Controller #2 00h 1Bh 00h Internal High Definition Audio controller 00h 1Ch 00h Internal PCI Express Root port 1 00h 1Ch 01h Internal PCI Express Root port 2 00h 1Ch 02h Internal PCI Express Root port 3 00h 1Ch 03h Internal PCI Express Root port 4 00h 1Ch 04h Internal PCI Express Root port 5 00h 1Ch 05h Internal PCI Express Root port 6 00h 1Ch 06h Internal PCI Express Root port 7 00h 1Ch 07h Internal PCI Express Root port 8 00h 1Dh 00h Internal Intel USB EHCI Controller #1 00h 1Eh 00h N/A Intel PCI to PCI Bridge 00h 1Fh 00h N/A Intel LPC Interface Bridge 00h 1Fh 02h Internal Intel SATA controller #1 00h 1Fh 03h Internal Intel SMBu s Controller 00h 1Fh 05h Internal Intel SATA controller #2 00h 1Fh 06h Internal Thermal Controller 11h 00h 0FFh Internal PCIE Port #0 12h 00h 0FFh Internal PCIE Port #1 13h 00h 0FFh Internal PCIE Port #2

Intel Integrated Graphics

Device

Intel Management Engine

Interface #1

Intel Management Engine

Interface #2

NuPRO-E72

Bus # Device # Function # Routing Description

14h 00h 0FFh Internal PCIE Port #3 15h 00h 0FFh Internal Intel 82574L LAN Controller 16h 00h 0FFh Internal PCIE Port #5 17h 00h 0FFh Internal USB 3.0 Controller 18h 00h 0FFh Internal PCIE Port #7 20h 0Fh 00h Internal PCI Slot 0 20h 0Eh 00h Internal PCI Slot 1 20h 0Dh 00h Internal PCI Slot 2 20h 0Ch 00h Internal PCI Slot 3 20h 0Bh 00h Internal PCI Slot 4

Table C-6: PCI Configuration Space Map

PCI Interrupt Routing Map

PIRQ A B C D E F G H

INT Line INTA INTB INTC INTD

P.E.G. Root Port INTA INTB INTC INTD

VGA X

SATA Controller X X

SATA Controller 1 X

SMBus controller X

Thermal Controller X

EHCI 1 X EHCI 2 X

HDA X

Intel GBE X HECI host 1 X HECI host 2 X

IDER Controller X

KT Controller X

PCIE port 0 INTA INTB INTC INTD PCIE port 1 INTB INTC INTD INTA PCIE port 2 INTC INTD INTA INTB PCIE port 3 INTD INTA INTB INTC PCIE port 4 INTA INTB INTC INTD PCIE port 5 INTB INTC INTD INTA PCIE port 6 INTC INTD INTA INTB PCIE port 7 INTD INTA INTB INTC

PCI Slot 0 X PCI Slot 1 X PCI Slot 2 X PCI Slot 3 X PCI Slot 4 X

Table C-7: PCI Interrupt Routing Map

NuPRO-E72

Important Safety Instructions

For user safety, please read and follow all instructions, WARNINGS, CAUTIONS, and NOTES marked in this manual

and on the associated equipment before handling/operating the equipment.

X Read these safety instructions carefully. X Keep this user’s manual for future reference. X Read the specifications section of this manual for detailed

information on the operating environment of this equipment.

X When installing/mounting or uninstalling/removing

equipment:

Z Turn off power and unplug any power cords/cables.

X To avoid electrical sh ock and/or damage to equipment:

Z Keep equipment away from water or liquid sources; Z Keep equipment away from high heat or high humidity; Z Keep equipment properly ventilated (do not block or

cover ventilation openings);

Z Make sure to use recommended voltage and power

source settings;

Z Always install and operate equipment near an easily

accessible electrical socket-outlet;

Z Secure the power cord (do not place any object on/over

the power cord);

Z Only install/attach and operate equipment on stable

surfaces and/or recommended mountings; and,

Z If the equipment will not be used for long periods of time,

turn off and unplug the equipment from its power source.

X Never attempt to fix the equipment. Equipment should only

be serviced by qualified personnel.

A Lithium-type battery may be provided for uninterrupted, backup or emergency power.

Risk of explosion if battery is replaced with one of an incorrect type. Dispose of used batteries appropriately.

WARNING:

X Equipment must be serviced by authorized technicians

when:

Z The power cord or plug is damaged; Z Liquid has penetrated the equipment; Z It has been exposed to high humidity/moisture; Z It is not functioning or does not function according to the

user’s manual;

Z It has been dropped and/or damaged; and/or, Z It has an obvious sign of breakage.

Getting Service

ADLINK Technology, Inc.

Address: 9F, No.166 Jian Yi Road, Zhonghe District New Taipei City 235, Taiwan

ᄅקؑխࡉ೴৬ԫሁ 166 ᇆ 9 ᑔ

Tel: +886-2-8226-5877 Fax: +886-2-8226-5717 Email: service@adlinktech.com

Ampro ADLINK Technology, Inc.

Address: 5215 Hellyer Avenue, #110 San Jose, CA 95138, USA Tel: +1-408-360-0200 Toll Free: +1-800-966-5200 (USA only) Fax: +1-408-360-0222 Email: info@adlinktech.com

ADLINK Technology (China) Co., Ltd.

Address: Ϟ⍋Ꮦ⌺ϰᮄᓴ∳催⾥ᡔು㢇᯹䏃 300 ো(201203) 300 Fang Chun Rd., Zhangjiang Hi-Tech Park

Pudong New Area, Shanghai, 201203 China Tel: +86-21-5132-8988 Fax: +86-21-5132-3588 Email: market@adlinktech.com

NuPRO-E72

ADLINK Technology Beijing

Address: ࣫ҀᏖ⍋⎔Ϟഄϰ䏃 1 োⲜ߯ࡼ࡯໻ E ᑻ 801 ᅸ(100085)

Rm. 801, Power Creative E, No. 1 Shang Di East Rd. Beijing, 100085 China Tel: +86-10-5885-8666 Fax: +86-10-5885-8626 Email: market@adlinktech.com

ADLINK Technology Shenzhen

Address: ⏅ഇᏖቅ⾥ᡔು催ᮄϗ䘧᭄ᄫᡔᴃು

A1 󰶀 2 ὐ C  (518057)

2F, C Block, Bldg. A1, Cyber-Tech Zone, Gao Xin Ave. Sec. 7

High-Tech Industrial Park S., Shenzhen, 518054 China Tel: +86-755-2643-4858 Fax: +86-755-2664-6353 Email: market@adlinktech.com

LiPPERT ADLINK Technology GmbH

Address: Hans-Thoma-Strasse 11, D-68163 Mannheim, Germany Tel: +49-621-43214-0 Fax: +49-621 43214-30 Email: emea@adlinktech.com

ADLINK Technology, Inc. (French Liaison Office)

Address: 6 allée de Londres, Immeuble Ceylan 91940 Les Ulis, France Tel: +33 (0) 1 60 12 35 66 Fax: +33 (0) 1 60 12 35 66 Email: france@adlinktech.com

ADLINK Technology Japan Corporation

Address: ͱ101-0045 ᵅҀ䛑ҷ⬄⼲⬄䤯ފ⬎ 3-7-4

Tel: +81-3-4455-3722 Fax: +81-3-5209-6013 Email: japan@adlinktech.com

ADLINK Technology, Inc. (Korean Liaison Office)

Address: 137-881 昢殾柢昢爎割昢爎堆嵢 326, 802 (昢爎壟, 微汾瘶捒娯)

Tel: +82-2-2057-0565 Fax: +82-2-2057-0563 Email: korea@adlinktech.com

ADLINK Technology Singapore Pte. Ltd.

Address: 84 Genting Lane #07-02A, Cityneon Design Centre

Tel: +65-6844-2261 Fax: +65-6844-2263 Email: singapore@adlinktech.com

ADLINK Technology Singapore Pte. Ltd. (Indian Liaison Office)

Address: #50-56, First Floor, Spearhead Towers

Malleswaram, Bangalore - 560 055, India Tel: +91-80-65605817, +91-80-42246107 Fax: +91-80-23464606 Email: india@adlinktech.com

⼲⬄ 374 ɛɳ 4F KANDA374 Bldg. 4F, 3-7-4 Kanda Kajicho, Chiyoda-ku, Tokyo 101-0045, Japan

802, Mointer B/D, 326 Seocho-daero, Seocho-Gu, Seoul 137-881, Korea

Singapore 349584

Margosa Main Road (between 16th/17th Cross)

ADLINK Technology, Inc. (Israeli Liaison Office)

Address: 27 Maskit St., Corex Building PO Box 12777 Herzliya 4673300, Israel Tel: +972-77-208-0230 Fax: +972-77-208-0230 Email: israel@adlinktech.com

ADLINK Technology, Inc. (UK Liaison Office)

Tel: +44 774 010 59 65 Email: UK@adlinktech.com

ADLINK NuPRO-E72 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

NuPRO-E72

Revision History

Preface

Table of Contents

List of Figures

List of Tables

1 Introduction

1.1 Overview

1.2 Features

1.3 Specifications

1.4 Block Diagram

1.5 Functional Description

Processor Support

Intel® C226 Express Chipset

Dual-Channel DDR3 ECC Memory

Gigabit Ethernet

Serial ATA

Universal Serial Bus (USB 2.0/3.0)

Hardware monitoring

Watchdog Timer

Trusted Platform Module

Intel® Active Management Technology

1.6 Mechanical Drawing

1.7 I/O Connectivity

1.8 Power Consumption

1.8.1 Intel® Xeon® Processor E3-1225 v3 3.2GHz (84W)

1.8.2 Intel® Xeon® Processor E3-1268L v3 2.30 GHz (45W)

1.8.3 Intel® Core™ i3-4330 Processor 3.5GHz (54W)

1.8.4 Intel® Celeron® G1820 Processor 2.7GHz (53W)

1.9 Rear I/O Panel

USB 3.0 Connectors

LAN (RJ-45) Ports

VGA Port

1.10 Board Layout

1.11 Onboard Connectors

COM1~6 Connector (RS-232) (CN11~14/16/23)

COM1 Connector (RS-422/485) (CN23)

USB 3.0 Connectors (CN36/37)

DVI-D Onboard Connector(CN17)

DVI-D Bracket Connector

ATX 12V Power Connector (CN24)

PS/2 Keyboard/Mouse Pin Header (CN27)

Serial ATA Connectors (CN30~33)

HD Audio Daughter Board Connector (CN40)

System Panel Connector (CN45)

Fan Connectors (FAN1/2)

2 Getting Started

2.1 Package Contents

2.2 Installing the CPU

2.3 Installing the CPU Fan and Heatsink

2.4 Installing Memory Modules

Memory Configuration Options

2.5 Jumpers & Switches

Clear CMOS Jumper (JBAT1)

Clear RTC Jumper (JBAT2)

After power up, remove the jumper cap from pins 2-3 and reinstall it to pins 1-2.

COM1 Mode Switch (SW13)

2.6 Driver Installation

2.6.1 Installing Chipset Driver

2.6.2 Installing Graphics Driver

2.6.3 Installing Ethernet Driver

2.6.4 Installing Management Engine Driver

2.6.5 Installing USB 3.0 Driver

Appendix A BIOS Setup

A.1 Starting the BIOS

Setup Menu

Navigation

Hotkey Descriptions

A.2 Main Setup

System & Board Info

System Time/System Date

Access Level

A.3 Advanced BIOS Setup

A.3.1 ACPI Settings

A.3.2 Trusted Computing

A.3.3 CPU Configuration