Page 1
Inno Color Beam Z19
©2013 ADJ Products, LLC all rights reserved. Information,
specications, diagrams, images, and instructions herein are
subject to change without notice. ADJ Products, LLC logo and
identifying product names and numbers herein are trademarks
of ADJ Products, LLC. Copyright protection claimed includes all
forms and matters of copyrightable materials and information
now allowed by statutory or judicial law or hereinafter granted.
Product names used in this document may be trademarks or
registered trademarks of their respective companies and are
hereby acknowledged. All non-ADJ Products, LLC brands and
product names are trademarks or registered trademarks of their
respective companies.
ADJ Products, LLC and all aliated companies hereby disclaim any and all liabilities for property, equipment, building, and
electrical damages, injuries to any persons, and direct or indirect economic loss associated with the use or reliance of any
information contained within this document, and/or as a result
of the improper, unsafe, unsucient and negligent assembly,
installation, rigging, and operation of this product.
1/13
User Instructions
Europe Energy Saving Notice
Energy Saving Matters (EuP 2009/125/EC)
Saving electric energy is a key to help protecting the enviroment.
Please turn o all electrical products when they are not in use. To
avoid power consumption in idle mode, disconnect all electrical
equipment from power when not in use. Thank you!
Page 2
Inno Color Beam Z19 Introduction
Inno Color Beam Z19 General Instructions
Unpacking: Thank you for purchasing the Inno Color Beam Z19 by
ADJ Products, LLC. Every Inno Color Beam Z19 has been thoroughly
tested and has been shipped in perfect operating condition. Carefully
check the shipping carton for damage that may have occurred during
shipping. If the carton appears to be damaged, carefully inspect your
xture for any damage and be sure all accessories necessary to operate the unit has arrived intact. In the case damage has been found
or parts are missing, please contact our toll free customer support
number for further instructions. Do not return this unit to your dealer
without rst contacting customer support.
Introduction: The Inno Color Beam Z19 is part of ADJ’s continuing
pursuit for creating high quality affordable intelligent fixtures. The Inno
Color Beam Z19 is a high performance, DMX intelligent, moving head
LED fixture. This fixture is a great piece for retail stores, displays, mood,
architectural, interior and exterior decoration, and clubs. This unit can
be used as a stand alone, or in a Master/Slave conguration. The unit
can also be controlled via DMX controller. This fixture is suitable for
theaters, studios, retail stores, and other similar locations.
Customer Support: ADJ Products, LLC provides a toll free cus-
tomer support line, to provide set up help and to answer any question
should you encounter problems during your set up or initial operation.
You may also visit us on the web at www.adj.com for any comments
or suggestions. Service Hours are Monday through Friday 8:00 a.m. to
4:30 p.m. Pacic Standard Time.
Voice: (800) 322-6337
Fax: (323) 582-2941
E-mail: support@americandj.com
To purchase parts online visit http://parts.americandj.com
Warning! To prevent or reduce the risk of electrical shock or re, do
not expose this unit to rain or moisture.
Caution! There are no user serviceable parts inside this unit. Do not
attempt any repairs yourself, doing so will void your manufactures warranty. In the unlikely event your unit may require service please contact
ADJ Products, LLC.
PLEASE recycle the shipping carton when ever possible.
To optimize the performance of this product, please read these operating instructions carefully to familiarize yourself with the basic operations
of this unit. These instructions contain important safety information
regarding the use and maintenance of this unit. Please keep this manual
with the unit, for future reference.
Inno Color Beam Z19 Features
• RGBW Color Mixing
• 19 x 10W High Quatlity Osram Ostar Quad Color LEDs
• Color Strobe Effect
• Color Mix Effect
• Pan/Tilt Inversion
• Electronic Dimming 0-100%
• Dimmer Curve
• Built in Microphone
• DMX-512 protocol
• 14 DMX Channels
• 3 Operating Modes - Sound Active, Show Mode, & DMX Control
• Power Cord Daisy Chaining (See section below)
Inno Color Beam Z19 Power Cord Daisy Chaining
With this feature you can connect the xtures to one another
using the IEC input and output sockets. The quantity that can be
connected is 5 xtures maximum for 120V and 11 xtures maximum for 240V. After the maximum xtures has been reached you
will need to use a new power outlet. They must be the same xtures. DO NOT mix xtures.
Inno Color Beam Z19 Warranty Registration
The Inno Color Beam Z19 carries a 3 year (1095 days) limited war-
ranty. Please fill out the enclosed warranty card to validate your
purchase and warranty. You may also register your product online at
www. americandj.com. All returned service items whether under warranty or not, must be freight pre-paid and accompany a return authorization (R.A.) number. If the unit is under warranty you must provide a
copy of your proof of purchase invoice. Please contact ADJ customer
support for a R.A. number.
ADJ Products, LLC - www.adj.com - Inno Color Beam Z19 User Manual Page 3ADJ Products, LLC - www.adj.com - Inno Color Beam Z19 User Manual Page 2
Page 3
Inno Color Beam Z19 Safety Precautions
Inno Color Beam Z19 Installation
• To reduce the risk of electrical shock or re, do not expose this unit
rain or moisture
• Do not spill water or other liquids into or on to your unit.
• Be sure that the local power outlet match that of the required volt age for your unit.
• Do not attempt to operate this unit if the power cord has been
frayed or broken. Do not attempt to remove or break o the ground
prong from the electrical cord. This prong is used to reduce the risk
of electrical shock and re in case of an internal short.
• Disconnect from main power before making any type of connection.
• Do not remove the cover under any conditions. There are no user
serviceable parts inside.
• Never operate this unit when it’s cover is removed.
• Never plug this unit in to a dimmer pack
• Always be sure to mount this unit in an area that will allow proper
ventilation. Allow about 6” (15cm) between this device and a wall.
• Do not attempt to operate this unit, if it becomes damaged.
• This unit is intended for indoor use only, use of this product out`
doors voids all warranties.
• During long periods of non-use, disconnect the unit’s main power.
• Always mount this unit in safe and stable matter.
• Power-supply cords should be routed so that they are not likely to
be walked on or pinched by items placed upon or against them,
paying particular attention to the point they exit from the unit.
• Cleaning -The fixture should be cleaned only as recommended by
t he manufacturer. See page 22 for cleaning details.
• Heat -The appliance should be situated away from heat sources
such as radiators, heat registers, stoves, or other appliances (inclu d ing amplifiers) that produce heat.
• The fixture should be serviced by qualified service personnel when:
A. The power-supply cord or the plug has been damaged.
B. Objects have fallen, or liquid has been spilled into the appliance.
C. The appliance has been exposed to rain or water.
D. The appliance does not appear to operate normally or exhibits a
marked change in performance.
When installing the unit, the trussing or area of installation must be
able to hold 10 times the weight without any deformation. When
installing the unit must be secured with a secondary safety attachment, e.g. and appropriate safety cable. Never stand directly below
the unit when mounting, removing, or servicing the unit.
Overhead mounting requires extensive experience, including calculating working load limits, installation material being used, and perodic
safety inspection of all installation material and unit. If you lack these
qualications, do not attempt the installation yourself.
These installaiton should be checked by a skilled person once a year.
The Inno Color Beam Z19 is fully operational in two dierent mounting positions, hanging upside-down from a ceiling or set on a at level
surface. To avoid internal damage to the unit, never mount the unit on
its side as illustrated above. Be sure this xture is kept at least 0.5m
away from any ammable materials (decoration etc.). Always use
and install the supplied safety cable as a safety measure to prevent
accidental damage and/or injury in the event the clamp fails (see next
page). Never use the carrying handles for secondary attachment.
ADJ Products, LLC - www.adj.com - Inno Color Beam Z19 User Manual Page 4
ADJ Products, LLC - www.adj.com - Inno Color Beam Z19 User Manual Page 5
Page 4
Inno Color Beam Z19 Installation
Inno Color Beam Z19 Set Up
NOTICE: The suitable enviromental temperature for this light-
ing xture is between -25˚ C to 45˚ C. Do not place this lighting
xture in an enviroment where the temperatures are under or
above the temperatures stated above. This will allow the xture
to run at its best and help prolong the xture life.
Power Supply: The ADJ Inno Color Beam Z19 contains a automatic
voltage switch, which will auto sense the voltage when it is plugged
into a power source. With this switch there is no need to worry about
the correct power voltage, this unit can be plugged in anywhere.
DMX-512: DMX is short for Digital Multiplex. This is a universal pro-
tocol used as a form of communication between intelligent fixtures
and controllers. A DMX controller sends DMX data instructions from
the controller to the fixture. DMX data is sent as serial data that travels from fixture to fixture via the DATA “IN” and DATA “OUT” XLR terminals located on all DMX fixtures (most controllers only have a DATA
“OUT” terminal).
DMX Linking: DMX is a language allowing all makes and models of
dierent manufactures to be linked together and operate from a single
controller, as long as all xtures and the controller are DMX compliant. To ensure proper DMX data transmission, when using several
DMX fixtures try to use the shortest cable path possible. The order
in which fixtures are connected in a DMX line does not influence the
DMX addressing. For example; a fixture assigned a DMX address of 1
may be placed anywhere in a DMX line, at the beginning, at the end,
or anywhere in the middle. When a fixture is assigned a DMX address
of 1, the DMX controller knows to send DATA assigned to address 1
to that unit, no matter where it is located in the DMX chain.
Data Cable (DMX Cable) Requirements (For DMX Operation):
The Inno Color Beam Z19 can be controlled via DMX-512 protocol. The
Inno Color Beam Z19 is a 14 Channel DMX unit. The DMX address is
set on the front panel of the Inno Color Beam Z19. Your unit and your
Screw one clamp via a M12 screw and nut onto the Omega
holder. Insert the quick-lock fasteners of the Omega holder into
the respective holes on the bottom of the Inno Color Beam Z19.
Tighten the quick-lock fasteners fully clockwise. Pull the safetycable through the eyehole hook on the bottom of the base and
over the trussing system or a safe xation spot. Insert the end in
the carabine and tighten the safety screw.
ADJ Products, LLC® - www.adj.com - Inno Color Beam Z19 User Manual Page 6 ADJ Products, LLC - www.adj.com - Inno Color Beam Z19 User Manual Page 7
DMX controller require a approved DMX-512 110 Ohm Data cable for
data input and data output (Figure 1). We recommend Accu-Cable
DMX cables. If you are making your own cables,
be sure to use standard 110-120 Ohm shielded
cable (This cable may be purchased at almost
all professional sound and lighting stores). Your
cables should be made with a male and female
XLR connector on either end of the cable. Also
remember that DMX cable must be daisy chained
and cannot be split.
Figure 1
Page 5
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
DMX512
DMX+,DMX-,COMMON
1
2
3
Termination reduces signal errors and
avoids signal transmission problems
and interference. It is always advisable
to connect a DMX terminal, (Resistance
120 Ohm 1/4 W) between PIN 2 (DMX-)
and PIN 3 (DMX +) of the last fixture.
POWER
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
Inno Color Beam Z19 Set Up
Notice: Be sure to follow gures two and three when making your own
cables. Do not use the ground lug on the XLR connector. Do not connect the cable’s shield conductor to the ground lug or allow the shield
conductor to come in contact with the XLR’s outer casing. Grounding
the shield could cause a short circuit and erratic behavior.
1
2
XLR Male Socket
1 Ground
Figure 3
DMX512 OUT
3-PIN XLR
2 Cold
3 Hot
3
XLR Female Socket
2 Cold
COMMON
DMX +
DMX -
1 Ground
3 Hot
1
DMX512 IN
3
3-PIN XLR
2
Figure 2
XLR Pin Conguration
Pin 1 = Ground
Pin 2 = Data Compliment (negative)
Pin 3 = Data True (positive)
Inno Color Beam Z19 System Menu
Special Note: Line Termination.
When longer runs of cable are
used, you may need to use a terminator on the last unit to avoid erratic
behavior. A terminator is a 90-120 ohm 1/4 watt resistor which is connected between pins 2 and 3 of a male XLR connector (DATA + and
DATA -). This unit is inserted in the female XLR connector of the last
unit in your daisy chain to terminate the line. Using a cable terminator
(ADJ part number Z-DMX/T) will decrease the possibilities of erratic
behavior.
5-Pin XLR DMX Connectors.
Termination reduces signal errors and
1
avoids signal transmission problems
3
and interference. It is always advisable
2
to connect a DMX terminal, (Resistance
120 Ohm 1/4 W) between PIN 2 (DMX-)
and PIN 3 (DMX +) of the last fixture.
Some manufactures use 5-pin XLR
Figure 4
connectors for DATA transmission in place of 3-pin. 5-pin XLR xtures
may be implemented in a 3-pin XLR DMX line. When inserting standard
5-pin XLR connectors in to a 3-pin line a cable adaptor must be used,
these adaptors are readily available at most electric stores. The chart
below details a proper cable conversion.
3-Pin XLR to 5-Pin XLR Conversion
Conductor 5-Pin XLR Male (In)3-Pin XLR Female (Out)
Ground/Shield
Data Compliment (- signal)
Data True (+ signal)
Not Used
Not Used
Pin 1
Pin 2
Pin 3
Pin 1
Pin 2
Pin 3
Do Not Use
Do Not Use
ADJ Products, LLC - www.adj.com - Inno Color Beam Z19 User Manual Page 8 ADJ Products, LLC - www.adj.com - Inno Color Beam Z19 User Manual Page 9
Page 6
Inno Color Beam Z19 System Menu
Inno Color Beam Z19 System Menu
DMX Address - Set the DMX Address -
1. Press the MENU button until “DMX Addresss” is displayed,
press ENTER.
2. “X” will now be displayed, “X” represents the displayed address.
Press the UP or DOWN buttons to nd your desired address.
3. Press ENTER to conrm, and then press and hold the MENU
button for at least three seconds to assign.
Show Mode - Show modes 1 - 4 (Factory Shows).
1. Press the MENU button until “Show Mode” is displayed, press
ENTER.
2. “Show X” will now be displayed, “X” representing a number
between 1-4. Press the UP or DOWN buttons to nd your desired
show and press ENTER to conrm. After pressing ENTER, press
and hold the MENU button for at least 3 seconds to activate.
Dimmer Curve - In this mode you can select the dimmer
curve.
1. Press the MENU button until “Dimmer Curve” is displayed,
press ENTER.
2. The current dimmer curve will be displayed.
2. Press the UP or DOWN buttons until your desired mode is
displayed, press ENTER to conm.
NOTE: In a Master/Slave conguration you can make one xture the Master and then set the next xture to “Slave 2”, the
xtures will now have contrast movement to each other.
Blackout - This will activate/deactivate blackout
1. Press the MENU button until “Blackout” is displayed, press
ENTER.
2. Either “Yes” or “No” will now be displayed. Press the UP or
DOWN buttons to toggle between “Yes” and “No”.
3. Press ENTER to conrm your setting.
Sound State - In this mode the unit will run in sound
active mode.
1. Press the MENU button until “Sound State” is displayed, press
ENTER.
2. Either “On” or “O” will now be displayed. Use the UP or
DOWN buttons to toggle between “On” and “O”.
3. Press ENTER to conrm your selection, the press and hold the
MENU button to activate.
3. Press the UP or DOWN buttons to nd your desired dimmer
curve and press ENTER to conrm.
Slave Mode - This will let you set unit as a master or
slave in a master/slave conguration.
1. Press the MENU button until “Slave Mode” is displayed,
press ENTER. Either “Master”, “Slave 1” or “Slave 2” will be
displayed.
Sound Sense - In this mode you can adjust the sound
sensitivity of the sound active mode.
1. Press the MENU button until “Sound Sense” is displayed,
press ENTER.
2. Press the UP or DOWN buttons to adjust the sensitivity level.
The sensitivity level can be adjusted between 0 (the lowest) and
100 (most sensitive).
ADJ Products, LLC - www.adj.com - Inno Color Beam Z19 User Manual Page 11ADJ Products, LLC - www.adj.com - Inno Color Beam Z19 User Manual Page 10
Page 7
Inno Color Beam Z19 System Menu Inno Color Beam Z19 System Menu
3. Press ENTER to set you desired level.
Pan Inverse - Pan Inversion
1. Press the MENU button until “Pan Inverse” is displayed,
press ENTER. Either “Yes” or “No” will be displayed.
2. To activate the Pan inversion press the UP or DOWN buttons
until “Yes” is displayed, press ENTER to conm. To deactivate
Pan inversion, select “No” and press Enter.
Tilt Inverse - Tilt Inversion
1. Press the MENU button until “Tilt Inverse” is displayed, press
ENTER. Either “Yes” or “No” will be displayed.
2. To activate the Tilt inversion press the UP or DOWN buttons
until “Yes” is displayed, press ENTER to conm. To deactivate
Tilt inversion, select “No” and press Enter.
Back Light Auto O - With this function you can make
the backlight automatically turn off after one minute.
2. Either “No Delay” or time between 1s - 3s will be displayed.
This number represents the delay setting. Use the UP and DOWN
buttons to adjust the blackout delay.
Example: If the delay is set to 3 seconds, when you are in 14
Channel mode under DMX control, and the channel 12 values are
between 226-235, the xture will move, and then blackout after
3 seconds.
3. Press ENTER to conrm.
White Balance - With this function you can adjust the
RGB colors to make your desired color.
1. Press the MENU button until “White Balance” is displayed,
press ENTER.
2. Use the UP or DOWN buttons to nd the color you wish to
adjust.
3. Once you nd the color you want to adjust press ENTER, the
displayed value will begin to ash. Use the UP or DOWN buttons to adjust the value. Once you have made your adjustment
press ENTER.
1. Press the MENU button until “Back Light Auto O” is displayed, press ENTER.
2. Either “No” or “Yes” will now be displayed. Press the UP or
DOWN buttons to select “Yes” to keep the backlight on at all
times, or “No” to allow the backlight to turn o after 2 minutes.
Press any button to turn the backlight on again.
3. Press ENTER to conrm.
Function Delay - With this function the blackout func-
tion under 14 Channel mode can be delayed.
1. Press the MENU button until “Function Delay” is displayed,
press ENTER.
4. Repeat steps 2-3 until satised.
Manual Test - With this function you can manually test
the individual features.
1. Press the MENU button until “Manual Test” is displayed,
press ENTER.
2. Use the UP or DOWN buttons to nd the functions that you
wish to test.
3. Once you nd a function you wish to test, press the ENTER
button, the displayed value will begin to ash. You can now
adjust the values by pressing the UP and DOWN buttons. Once
ADJ Products, LLC - www.adj.com - Inno Color Beam Z19 User Manual Page 13ADJ Products, LLC - www.adj.com - Inno Color Beam Z19 User Manual Page 12
Page 8
Inno Color Beam Z19 System Menu
Inno Color Beam Z19 System Menu
you have nished testing press the ENTER button.
4. To exit the manual test mode, press the MENU button.
Auto Test - This function will run a self test program.
1. Press the MENU button until “Auto Test” is displayed, press
ENTER.
2. The xture will now run a self test. Press the MENU button to
exit.
Fixture Use Time - With this function you can display
the running time of the unit.
1. Press the MENU button until “Fixture Use Time” is displayed,
press ENTER.
2. The running time of the xture will now be displayed. Press
MENU to exit.
Firmware Version - This will display the software ver-
sion
tings, and press ENTER.
Reset - Use this function to reset the motors.
1. Tap the MENU button until “Reset” is displayed, press
ENTER.
2. The xture will now reset the motors.
1. Press the MENU button until “Firmware Version” is displayed.
Press the ENTER button and the software vesion will be dis-
played.
2. Press the MENU button to leave this function.
PRO Default - This function will restore the factory set-
tings.
1. Press the MENU button until “PRO Default” is displayed,
press ENTER.
2. Either “YES” or “NO” will now be displayed. Press the UP or
DOWN buttons to select “YES” to switch back to defualt set-
ADJ Products, LLC - www.adj.com - Inno Color Beam Z19 User Manual Page 14
ADJ Products, LLC - www.adj.com - Inno Color Beam Z19 User Manual Page 15
Page 9
Inno Color Beam Z19 Universal DMX Control
Inno Color Beam Z19 14 Channel Mode
Universal DMX Control: This function allows you to use a Elation®
universal DMX-512 controller to control the chases and patterns,
dimmer and strobe. A DMX controller allows you to create unique
programs tailored to your individual needs. The Inno Color Beam Z19
has 14 DMX Channels.
1. This function will allow you to control each individual fixture’s
traits with a standard DMX 512 controller. See pages 17-20 for
the DMX traits.
2. To run your fixture in DMX mode, set your desired DMX address
following the directions on page 10, and the set-up specifications
that come with your DMX controller.
3. Plug in the fixture via the XLR connections to any standard DMX
controller.
4. For longer cable runs (more than a 100 feet) use a terminator on
the last fixture.
Inno Color Beam Z19 Master-Slave Configuration
Master-Slave Conguration: This function will allow you to link up
to 16 units together and operate without a controller. The units will be
sound activated. In Master-Slave operation one unit will act as the controlling unit and the others will react to the controlling units programs.
Any unit can act as a Master or as a Slave.
1. Using approved DMX data cables, daisy chain your units togeth-
er via the XLR connector on the rear of the units. Remember the
Male XLR connector is the input and the Female XLR connector
is the output. The rst unit in the chain (master) will use the female
XLR connector only - The last unit in the chain will use the male
XLR connector only. For longer cable runs we suggest a termina tor at the last fixture.
2. Set the Master unit to your desired operating mode.
3. On the slave units press the MENU button until “Slave Mode” is
displayed, and Press ENTER. Choose either “Slave 1” or “Slave 2”
and press ENTER. See page 11 for more info.
4. The slave units will now follow the Master unit.
Channel Value Function
1 PAN
0 - 255 0° - 540°
2 0 - 255 PAN FINE
3 TILT
0 - 255 0° - 220°
4 0 - 255 TILT FINE
5 RED
0 - 255 0% - 100%
6 GREEN
0 - 255 0% - 100%
7 BLUE
0 - 255 0% - 100%
8 WHITE
0 - 255 0% - 100%
9 COLOR MACROS
0 OFF
1 - 4 MACRO 1
5 - 8 MACRO 2
9 - 12 MACRO 3
13 - 16 MACRO 4
17 - 20 MACRO 5
21 - 24 MACRO 6
25 - 28 MACRO 7
29 - 32 MACRO 8
33 - 36 MACRO 9
37 - 40 MACRO 10
41 - 44 MACRO 11
45 - 48 MACRO 12
49 - 52 MACRO 13
53 - 56 MACRO 14
57 - 60 MACRO 15
61 - 64 MACRO 16
65 - 68 MACRO 17
69 - 72 MACRO 18
ADJ Products, LLC - www.adj.com - Inno Color Beam Z19 User Manual Page 17ADJ Products, LLC - www.adj.com - Inno Color Beam Z19 User Manual Page 16
Page 10
Inno Color Beam Z19 14 Channel Mode
Inno Color Beam Z19 14 Channel Mode
Channel Value Function
9 COLOR MACROS
73 - 76 MACRO 19
77 - 80 MACRO 20
81 - 84 MACRO 21
85 - 88 MACRO 22
89 - 92 MACRO 23
93 - 96 MACRO 24
97 - 100 MACRO 25
101 - 104 MACRO 26
105 - 108 MACRO 27
109 - 112 MACRO 28
113 - 116 MACRO 29
117 - 120 MACRO 30
121 - 124 MACRO 31
125 - 128 MACRO 32
129 - 132 MACRO 33
133 - 136 MACRO 34
137 - 140 MACRO 35
141 - 144 MACRO 36
145 - 148 MACRO 37
149 - 152 MACRO 38
153 - 156 MACRO 39
157 - 160 MACRO 40
161 - 164 MACRO 41
165 - 168 MACRO 42
169 - 172 MACRO 43
173 - 176 MACRO 44
177 - 180 MACRO 45
181 - 184 MACRO 46
185 - 188 MACRO 47
189 - 192 MACRO 48
193 - 196 MACRO 49
197 - 200 MACRO 50
201 - 204 MACRO 51
Channel Value Function
9 COLOR MACROS
205 - 208 MACRO 52
209 - 212 MACRO 53
213 - 216 MACRO 54
217 - 220 MACRO 55
221 - 224 MACRO 56
225 - 228 MACRO 57
229 - 232 MACRO 58
233 - 236 MACRO 59
237 - 240 MACRO 60
241 - 244 MACRO 61
245 - 248 MACRO 62
249 - 252 MACRO 63
253 - 255 MACRO 64
10 SHUTTER/STROBING
0 - 19 SHUTTER CLOSED
20 - 24 OPEN
25 - 64 STROBING FAST - SLOW
65 - 69 OPEN
70 - 84 SLOW OPEN - FAST CLOSE
85 - 89 OPEN
90 - 104 FAST OPEN - SLOW CLOSE
105 - 109 OPEN
110 - 124 RANDOM STROBE
125 - 129 OPEN
130 - 144 RANDOM OPENING PULSE
145 - 149 OPEN
150 - 164 RANDOM CLOSING PULSE
165 - 169 OPEN
170 - 184 BURST PULSE
185 - 189 OPEN
190 - 204 RANDOM BURST PULSE
205 - 209 OPEN
210 - 224 PULSING
ADJ Products, LLC - www.adj.com - Inno Color Beam Z19 User Manual Page 18 ADJ Products, LLC - www.adj.com - Inno Color Beam Z19 User Manual Page 19
Page 11
Inno Color Beam Z19 14 Channel Mode
Dimmer
0S (Fade Tim e)
1S (Fade Time)
19 40
Channel Value Function
10 SHUTTER/STROBING
225 - 229 OPEN
230 - 244 BURST
245 - 255 OPEN
11 MASTER DIMMER
0 - 255 0% - 100%
12 ZOOM
0 - 225 WIDE - NARROW
13 PAN/TILT MOVEMENT SPEED
0 - 225 MAX. - MIN. MOVEMENT SPED
14 RESET
0 - 9 NO FUNCTION
10 - 14 RESET ALL
15 - 255 NO FUNCTION
Inno Color Beam Z19 Dimmer Curve Chart
Inno Color Beam Z19 Photometric Chart
Ramp Effect
Standard
Stage
TV
Archit ec tu ral
Theatre
0
0
780
1180
1380
1580
T
down
0
dow n
（ ）
ms
T
0
1100
15 20
1730
0
1540
1860
2040
2230 22 80
T
dow n
0
1660
1940
2120
（ ）
ms
ADJ Products, LLC - www.adj.com - Inno Color Beam Z19 User Manual Page 21ADJ Products, LLC - www.adj.com - Inno Color Beam Z19 User Manual Page 20
Page 12
Inno Color Beam Z19 Fuse Replacement
Locate and remove the unit’s power cord. Once the cord has been
removed located the fuse holder located inside the power socket.
Insert a flat-head screw driver into the power socket and gently pry out
the fuse holder. Remove the bad fuse and replace with a new one. The
fuse holder has a built-in socket for a spare fuse be sure not to confuse
the spare fuse with active fuse.
Inno Color Beam Z19 Cleaning
Due to fog residue, smoke, and dust cleaning the internal and external optical lenses must be carried out periodically to optimize light
output.
Inno Color Beam Z19 Warranty
MANUFACTURER’S LIMITED WARRANTY
A. ADJ Products, LLC hereby warrants, to the original purchaser, ADJ Products, LLC products
to be free of manufacturing defects in material and workmanship for a prescribed period from
the date of purchase (see specific warranty period on reverse). This warranty shall be valid only if the
product is purchased within the United States of America, including possessions and
territories. It is the owner’s responsibility to establish the date and place of purchase by acceptable
evidence, at the time service is sought.
B. For warranty service you must obtain a Return Authorization number (RA#) before sending back the
product–please contact ADJ Products, LLC Service Department at 800-322-6337. Send the product
only to the ADJ Products, LLC factory. All shipping charges must be pre-paid. If the requested repairs or
service (including parts replacement) are within the terms of this warranty, ADJ Products, LLC will pay
return shipping charges only to a designated point within the United States. If the entire instrument is
sent, it must be shipped in it’s original package. No accessories should be shipped with the product. If
any accessories are shipped with the product, ADJ Products, LLC shall have no liability whatsoever for
loss of or damage to any such accessories, nor for the safe return thereof.
1. Use a soft cloth to wipe down the outside casing.
Cleaning frequency depends on the environment in which the fixture
operates (i.e. smoke, fog residue, dust, dew).
Inno Color Beam Z19 Troubleshooting
Listed below are a few common problems the user may encounter,
with solutions.
Unit not responding to DMX:
1. Check that the DMX cables are connected properly and are
wired correctly (pin 3 is “hot”; on some other DMX devices
pin 2 may be ‘hot’). Also, check that all cables are connected
to the right connectors; it does matter which way the inputs
and outputs are connected.
Unit does not respond to sound:
1. Quiet or high pitched sounds will not activate the unit.
2. Check the sound sensitivity level.
If problems are not resolved; Contact ADJ Products, LLC for service.
1-800-322-6337
ADJ Products, LLC - www.adj.com - Inno Color Beam Z19 User Manual Page 22
C. This warranty is void if the serial number has been altered or removed; if the product is modified in any
manner which ADJ Products, LLC concludes, after inspection, affects the reliability of the product; if the
product has been repaired or serviced by anyone other than the ADJ Products, LLC factory unless prior
written authorization was issued to purchaser by ADJ Products, LLC; if the product is damaged because
not properly maintained as set forth in the instruction manual.
D. This is not a service contract, and this warranty does not include maintnance, cleaning or periodic check
up. During the period specified above, ADJ Products, LLC will replace defective parts at its expense
with new or refurbished parts, and will absorb all expenses for warranty service and repair labor by
reason of defects in material or workmanship. The sole responsibility of ADJ Products, LLC under this
warranty shall be limited to the repair of the product, or replacement thereof, including parts, at the sole
discretion of ADJ Products, LLC. All products covered by this warranty were manufactured after August
15, 2012, and bear indentifying marks to that effect.
E. ADJ Products, LLC reserves the right to make changes in design and/or improvements upon its products
without any obligation to include these changes in any products theretofore manufactured.
No warranty, whether expressed or implied, is given or made with respect to any accessory supplied with
products described above. Except to the extent prohibited by applicable law, all implied warranties made
by ADJ Products, LLC in connection with this product, including warranties of merchantability or fitness,
are limited in duration to the warranty period set forth above. And no warranties, whether expressed or
implied, including warranties of merchantability or fitness, shall apply to this product after said period
has expired. The consumer’s and/or Dealer’s sole remedy shall be such repair or replacement as is
expressly provided above; and under no circumstances shall ADJ Products, LLC be liable for any loss or
damage, direct or consequential, arising out of the use of, or inability to use, this product.
This warranty is the only written warranty applicable to ADJ Products, LLC Products and
supersedes all prior warranties and written descriptions of warranty terms and conditions heretofore
published.
MANUFACTURER’S LIMITED WARRANTY PERIODS:
•LightingProducts=1-year(365days)LimitedWarranty(Such as: Special Effect Lighting, Intelligent
Lighting, UV lighting, Strobes, Fog Machines, Bubble Machines, Mirror Balls, Par Cans, Trussing,
Lighting Stands etc. excluding LEDs and lamps)
•LaserProducts=90-DayLimitedWarranty
•L.E.D.Products=3-year(1095days)LimitedWarranty(excluding motors, PCB boards, and power
supplies, which have a 1-year (365 day Limited Warranty) and batteries which have a 180 day
limited warranty). Only the L.E.D.s carry a 3-year warranty
ADJ Products, LLC - www.adj.com - Inno Color Beam Z19 User Manual Page 23
Page 13
Inno Color Beam Z19 Notes
Inno Color Beam Z19 Notes
ADJ Products, LLC - www.adj.com - Inno Color Beam Z19 User Manual Page 24
ADJ Products, LLC - www.adj.com - Inno Color Beam Z19 User Manual Page 25
Page 14
Inno Color Beam Z19 Specifications
SPECIFICATIONS:
Voltage: 100V~230V 50Hz/60Hz
LEDs: 19 x 10W Osram Quad Color LEDs
Power Consumption: 245W
Beam Angle: 10 ~ 60 Degrees
Fuse: 7Amp
Power Cord Daisy Chain: 5 Fixtures Max. (120V)
11 Fixtures Max (230V)
Weight: 21 lbs./ 9.5Kgs.
Dimensions: 13” (L) x 7.5” (W) x 15.75” (H)
329 x 188 x 395.4mm
Colors: RGBW Color Mixing
DMX Channels: 14 DMX Channels
Working Position: Any safe working position
Warranty: 3 Year (1095 days)
Auto Sensing Voltage: This xture contains a electronic bal-
last, which will auto sense the voltage when it is plugged into the
power source.
Please Note: Specications and improvements in the design of
this unit and this manual are subject to change without any prior
written notice.
ADJ Products, LLC - www.adj.com - Inno Color Beam Z19 User Manual Page 26
ADJ Products, LLC
6122 S. Eastern Ave. Los Angeles, CA 90040 USA
Tel: 323-582-2650 / Fax: 323-725-6100
Web: www.adj.com / E-mail: info@americandj.com
A.D.J. Supply Europe B.V.
Junostraat 2
6468 EW Kerkrade
Netherlands
service@adjgroup.eu / www.adj.eu
Tel: +31 45 546 85 00 / Fax: +31 45 546 85 99
Loading...