Page 1
XS 600
©2015 ADJ Products, LLC all rights reserved. Information,
specications, diagrams, images, and instructions herein are
subject to change without notice. ADJ Products, LLC logo and
identifying product names and numbers herein are trademarks
of ADJ Products, LLC. Copyright protection claimed includes all
forms and matters of copyrightable materials and information
now allowed by statutory or judicial law or hereinafter granted.
Product names used in this document may be trademarks or
registered trademarks of their respective companies and are
hereby acknowledged. All non-ADJ Products, LLC brands and
product names are trademarks or registered trademarks of their
respective companies.
ADJ Products, LLC and all aliated companies hereby disclaim any and all liabilities for property, equipment, building,
and electrical damages, injuries to any persons, and direct or
indirect economic loss associated with the use or reliance of
any information contained within this document, and/or as a
result of the improper, unsafe, unsucient and negligent assembly, installation, rigging, and operation of this product.
10/15
User Instructions
Europe Energy Saving Notice
Energy Saving Matters (EuP 2009/125/EC)
Saving electric energy is a key to help protecting the enviroment.
Please turn o all electrical products when they are not in use. To
avoid power consumption in idle mode, disconnect all electrical
equipment from power when not in use. Thank you!
Page 2
XS 600 General Information
XS 600 General Instructions
Unpacking: Thank you for purchasing the XS 600 by ADJ Products,
LLC. Every XS 600 has been thoroughly tested and has been shipped
in perfect operating condition. Carefully check the shipping carton for
damage that may have occurred during shipping. If the carton appears
to be damaged, carefully inspect your xture for any damage and be
sure all equipment necessary to operate the unit has arrived intact. In
the event damage has been found or parts are missing, please contact
our toll free customer support number for further instructions. Please
do not return this unit to your dealer without contacting customer support rst.
Introduction: The ADJ XS 600 is a new revolution in moving lights.
It features dual axis heads and has continuous 360 degree rotation in
both directions. The XS 600 can operate as a stand alone fixture or in
a Master/Slave configuration. The XS 600 has three operating modes;
sound active mode, show mode, and DMX control. This fixture is suitable for theaters, studios, retail stores, and other similar locations. For
best results use fog or special effects smoke to enhance the beams
projections.
Customer Support: ADJ Products, LLC provides a toll free cus-
tomer support line, to provide help and to answer any question should
you encounter problems during your set up or initial operation. You
may also visit us on the web at www.adj.com for any comments or
suggestions. Service Hours are Monday through Friday 8:00 a.m. to
4:30 p.m. Pacic Standard Time.
Voice: (800) 322-6337
Fax: (323) 582-2941
E-mail: support@americandj.com
Warning! To prevent or reduce the risk of electrical shock or re, do
not expose this unit to rain or moisture.
Caution! There are no user serviceable parts inside this unit. Do not
attempt any repairs yourself, doing so will void your manufactures
warranty. In the unlikely event your unit may require service please
contact ADJ Products, LLC.
ADJ Products, LLC will not accept any liability for any resulting damages caused by the non-observance of this manual or any unauthor-
ized modication to this unit.
ADJ Products, LLC - www.adj.com - XS 600 User Manual Page 2
To optimize the performance of this product, please read these
operating instructions carefully to familiarize yourself with the basic
operations of this unit. These instructions contain important safety
information regarding the use and maintenance of this unit. Please
keep this manual with the unit, for future reference.
XS 600 Features
• Multi-Colors
• 3 Operating Modes - Sound Active, Show Mode, and DMX Control
• 2 DMX Channel Modes (25 Channel Mode & 31 Channel Mode)
• Stand Alone or Master-Slave Setup
• Internal Microphone
• Digital Display for Address and Function Setting
• Power Cord Daisy Chain (See page 15)
• UC IR Compatible (Not Included) & Airstream IR Comptiable
XS 600 Warranty Registration
The XS 600 carries a 2 year (730 days) limited warranty. Please fill out
the enclosed warranty card to validate your purchase and warranty.
You may also register your product online at www. americandj.com.
All returned service items whether under warranty or not, must be
freight pre-paid and accompany a return authorization (R.A.) number.
If the unit is under warranty you must provide a copy of your proof of
purchase invoice. Please contact ADJ Products, LLC customer support for a R.A. number.
XS 600 Installation
The unit should be mounted using a mounting clamp (not provided),
axing it to the mounting bracket that is provided with the unit.
Always ensure that the unit is rmly xed to avoid vibration and slipping while operating. Always ensure that the structure to which you
are attaching the unit is secure and is able to support a weight of 10
times the unit’s weight. Also, always use a safety cable that can hold
12 times the weight of the unit when installing the xture. The equipment must be installed by a professional, and it must be installed in a
place where it is out of the reach of people’s grasp.
ADJ Products, LLC - www.adj.com - XS 600 User Manual Page 3
Page 3
XS 600 Safety Precautions
XS 600 DMX Set Up
For Your Own Personal Safety, Please Read and Understand This
Manual Completely Before You Attempt To Install Or Operate
This Unit!
• To reduce the risk of electrical shock or re, do not expose this unit
rain or moisture
• Do not spill water or other liquids into or on to your unit.
• Be sure that the local power outlet match that of the required volt age for your unit.
• Do not attempt to operate this unit if the power cord has been
frayed or broken.
• Do not attempt to remove or break o the ground prong from
the electrical cord. This prong is used to reduce the risk of electrical
shock and re in case of an internal short.
• Disconnect from main power before making any type of connection.
• Do not remove the cover under any conditions. There are no user
serviceable parts inside.
• Never operate this unit when it’s cover is removed.
• Always be sure to mount this unit in an area that will allow proper
ventilation. Allow about 6” (15cm) between this device and a wall.
• Do not attempt to operate this unit, if it becomes damaged.
• This unit is intended for indoor use only, use of this product out doors voids all warranties.
• Always mount this unit in safe and stable matter.
• Power-supply cords should be routed so that they are not likely to
be walked on or pinched by items placed upon or against them,
paying particular attention to cords at plugs, convenience recep tacles, and the point where they exit from the appliance.
• Cleaning -The fixture should be cleaned only as recommended by
the manufacturer. See page 28 for cleaning details.
• Heat -This fixture should be situated away from heat sources such
as radiators, heat registers, stoves, or other appliances (including
amplifiers) that produce heat.
• The fixture should be serviced by qualified service personnel when:
A. Objects have fallen, or liquid has been spilled into the appliance.
B. The appliance has been exposed to rain or water.
C. The appliance does not appear to operate normally or exhibits a
marked change in performance.
Power Supply: The ADJ XS 600 contains a automatic voltage switch,
which will auto sense the voltage when it is plugged into the power
source. With this switch there is no need to worry about the correct
power voltage, this unit can be plugged in anywhere.
DMX-512: DMX is short for Digital Multiplex. This is a universal pro-
tocol used by most lighting and controller manufactures as a form of
communication between intelligent fixtures and controllers. A DMX
controller sends DMX data instructions from the controller to the fixture. DMX data is sent as serial data that travels from fixture to fixture
via the DATA “IN” and DATA “OUT” XLR terminals located on all DMX
fixtures (most controllers only have a DATA “OUT” terminal).
DMX Linking: DMX is a language allowing all makes and models
of dierent manufactures to be linked together and operate from a
single controller, as long as all xtures and the controller are DMX
compliant. To ensure proper DMX data transmission, when using
several DMX fixtures try to use the shortest cable path possible. The
order in which fixtures are connected in a DMX line does not influence
the DMX addressing. For example; a fixture assigned a DMX address
of 1 may be placed anywhere in a DMX line, at the beginning, at the
end, or anywhere in the middle. Therefore, the first fixture controlled
by the controller could be the last fixture in the chain. When a fixture
is assigned a DMX address of 1, the DMX controller knows to send
DATA assigned to address 1 to that unit, no matter where it is located
in the DMX chain.
Data Cable (DMX Cable) Requirements (For DMX and Master/Slave
Operation): The XS 600 can be controlled via DMX-512 protocol. The
XS 600 has 5 DMX Channel Modes. The DMX address is set electronically using the controls on the front panel of the
unit. Your unit and your DMX controller require a
approved DMX-512 110 Ohm Data cable for data
input and data output (Figure 1). We recommend
Accu-Cable DMX cables. If you are making your
own cables, be sure to use standard 110-120 Ohm
shielded cable (This cable may be purchased at
almost all professional sound and lighting stores).
Your cables should be made with a male and
Figure 1
ADJ Products, LLC - www.adj.com - XS 600 User Manual Page 4 ADJ Products, LLC - www.adj.com - XS 600 User Manual Page 5
Page 4
XS 600 DMX Set Up
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
DMX512
DMX+,DMX-,COMMON
1
2
3
Termination reduces signal errors and
avoids signal transmission problems
and interference. It is always advisable
to connect a DMX terminal, (Resistance
120 Ohm 1/4 W) between PIN 2 (DMX-)
and PIN 3 (DMX +) of the last fixture.
POWER
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
XS 600 DMX Set Up
female XLR connector on either end of the cable. Also remember that
DMX cable must be daisy chained and cannot be split.
Notice: Be sure to follow gures two and three when making your own
cables. Do not use the ground lug on the XLR connector. Do not connect the cable’s shield conductor to the ground lug or allow the shield
conductor to come in contact with the XLR’s outer casing. Grounding
the shield could cause a short circuit and erratic behavior.
COMMON
1
DMX512 IN
3
3-PIN XLR
2
Figure 2
XLR Pin Conguration
Pin 1 = Ground
Pin 2 = Data Compliment (negative)
Pin 3 = Data True (positive)
XLR Male Socket
1 Ground
Figure 3
DMX512 OT
3-PIN XLR
2 Cold
3 Hot
1
3
2
XLR Female Socket
2 Cold
DMX +
DMX -
1 Ground
3 Hot
5-Pin XLR DMX Connectors.
Some manufactures use 5-pin DMX-
512 data cables for DATA transmission in place of 3-pin. 5-pin DMX
xtures may be implemented in a 3-pin DMX line. When inserting standard 5-pin data cables in to a 3-pin line a cable adaptor must be used,
these adaptors are readily available at most electric stores. The chart
below details a proper cable conversion.
3-Pin XLR to 5-Pin XLR Conversion
Conductor 5-Pin XLR Male (In)3-Pin XLR Female (Out)
Ground/Shield
Data Compliment (- signal)
Data True (+ signal)
Not Used
Not Used
Pin 1
Pin 2
Pin 3
Pin 1
Pin 2
Pin 3
Pin 4 - Do Not Use
Pin 5 - Do Not Use
XS 600 CAD Drawing
195.6
180.2
Special Note: Line Termination.
used, you may need to use a terminator on the last unit to avoid erratic
behavior. A terminator is a 110-120 ohm 1/4 watt resistor which is con-
When longer runs of cable are
nected between pins 2 and 3 of a male XLR connector (DATA + and
DATA -). This unit is inserted in the female XLR connector of the last
unit in your daisy chain to terminate the line. Using a cable terminator
(ADJ part number Z-DMX/T) will decrease the possibilities of erratic
behavior.
Termination reduces signal errors and
1
avoids signal transmission problems
3
and interference. It is always advisable
2
to connect a DMX terminal, (Resistance
120 Ohm 1/4 W) between PIN 2 (DMX-)
and PIN 3 (DMX +) of the last fixture.
ADJ Products, LLC - www.adj.com - XS 600 User Manual Page 6
Figure 4
317.7
317.7
94.6
125.7
ADJ Products, LLC - www.adj.com - XS 600 User Manual Page 7
Page 5
XS 600 System Menu XS 600 System Menu
UhIt 050- 255
MENU
Addr
Chnd
StAl
Shnd
Sond
SoSE
LASt
DiND
PInt
tIL1
tIL2
bAcL
dISP
Nan
Hrs
A001
A512
25CH
31CH
nASt
SLAu
Show0
Show8
ON
OFF
005
255
BLAc
HOLD
SHOu
StAn
StAG
tU
ArCH
tHE
ON
OFF
OFF
ON
OFF
ON
on
OFF
OFF
on
CH01
CH31
Starting DMX address
25CH=8bit
31CH=16bit DMX mode
nASt=Master
SLAu=Slave
Internal show, 0-8
Show to sound
Sound sensitivity, low~High
005-255
BLAc=blackout
HOLD=Hold last values
SHOu=Show mode
StAn=Standard
StAG=Stage
tU=TV
ArCH=Architectural
tHEA=Theatre
On=Counterclockwise
OFF=Clockwise
OFF=Clockwise
On=Counterclockwise
OFF=Clockwise
On=Counterclockwise
Display back light
O=normal
On=reverse
000-255
Total running hours
System Menu: When making adjustments press ENTER to
conrm your setup then press and hold the MENU button
for at least 3 seconds. To exit without making any adjust-
ments press the MENU button. The display will lock after 30
seconds, press the MENU button for 3 seconds to unlock.
ADDR - DMX Address Setting.
1. Press the either the MENU, UP, or DOWN buttons until “ADDR” is
displayed, press ENTER.
2. The current address will now be displayed and ashing. Press the
UP or DOWN buttons to nd your desired address. Press ENTER to
set your desired DMX address.
CHND - This will let select your desired DMX channel
mode.
1. Press the MENU button until “CHND” is displayed, press ENTER.
The current DMX channel mode will be displayed
2. Press the UP or DOWN buttons to nd your desired DMX channel
mode and press ENTER to conm and exit.
STAL - This will let you set unit as a master or slave in a
master/slave conguration.
1. Press the MENU button until “STAL” is displayed, press ENTER.
Either “MAST” or “SLAv” will be displayed.
2. Press the UP or DOWN buttons until your desired setting is displayed, press ENTER to conm.
Uer
rESt
BALA
ADJ Products, LLC - www.adj.com - XS 600 User Manual Page 8
Vx.x
on
OFF
rED 050-255
GrEN 050- 255
BluE 050- 255
Current software version
All motors reset
White balance adjust
SHND - Show modes 0-8 (Factory programs).
1. Press the MENU button until “SHND” is displayed, press ENTER.
2. “Sh X” will now be displayed, “X” representing a number between
0-8. Shows 0-8 are preset shows, while “Show 0” is random show.
Press the UP or DOWN buttons to nd your desired show and press
ADJ Products, LLC - www.adj.com - XS 600 User Manual Page 9
Page 6
XS 600 System Menu
XS 600 System Menu
ENTER to conrm. After pressing ENTER, press and hold the MENU
button for at least 3 seconds to activate.
3. When you have found your desired show press ENTER, then press
and hold the MENU button for at least 3 seconds to activate. After you
have set your desired show, it can be changed at any time using the
UP or DOWN buttons.
3. When you have found your desired show press ENTER, then press
and hold the MENU button for at least 3 seconds to activate. After
you have set your desired show, it can be changed at any time using
the UP or DOWN buttons.
SOND - Sound Active mode.
1. Press the MENU button until “SOND” is displayed, press ENTER.
2. The display will show either “ON” or “OFF”. Press the UP or
DOWN buttons to select “ON” to activate sound active mode, or
“OFF” to deactivate sound active mode.
3. Press ENTER to conrm.
SOSE - In this mode you can adjust the sound sensitiv-
ity.
1. Press the MENU button until “SOSE” is displayed, press ENTER.
2. A number between 5-255 will be displayed. Press the UP or DOWN
buttons to adjust the sound sensitivity. 5 being the least sensitive,
and 255 being the most sensitive.
3. When you have found your desired setting press ENTER to conrm.
LAST - This mode can be used as a precaution mode, that
in case the DMX signal is lost, interrupted, or power is lost,
the operating mode chosen in the setup is the running mode
the xture will go into when the DMX signal is lost. You can
also set this as the operating mode you would like the unit to
return to when power is applied.
1. Press the MENU button until “LAST” is displayed, and either
“BLAC”, “HOLD”, or “SHOU” will be displayed beneath.
2. Press ENTER and the bottom choice will begin to ash. Use the UP
or DOWN buttons to choose an operating mode you would like the unit
to start up in when power is applied or the DMX signal is lost.
• HOLD - If the DMX signal is lost the xture will stay in the last DMX
setting. If power is applied and this mode is set, the unit will automatically go into the last DMX set up.
• SHOU (Show Mode) - If the DMX signal is lost or power is applied,
the unit will automatically run a built-in show.
• BLAC (Blackout) - If the DMX signal is lost or interrupted, the unit will
automatically go into stand by mode.
3. Press ENTER to conrm your desired set up.
DIND - This will let select your desired dimmer curve.
1. Press the either the MENU button until “DIND” is displayed, press
ENTER. 1 of 5 dimmer curves will be displayed. “STAN” (standard),
“STAG” (stage), “TV” (TV), “ARCH” (architectural), or “THE” (theatre).
2. Press the UP or DOWN buttons to nd your desired dimmer curve
and press ENTER to conm and exit.
PINT - Pan Inversion (Clockwise or counter-clockwise
rotation)
1. Press the MENU button until “PINT” is displayed, press ENTER.
Either “On” or “Off” will be displayed.
2. To activate the Pan inversion (counter-clockwise rotation) press the
UP or DOWN buttons until “On” is displayed, press ENTER to conm.
To deactivate Pan inversion, select “Off” and press Enter.
TIL1 - Tilt Inversion
1. Press the MENU button until “TIL1” is displayed, press ENTER.
Either “On” or “Off” will be displayed.
ADJ Products, LLC - www.adj.com - XS 600 User Manual Page 10
ADJ Products, LLC - www.adj.com - XS 600 User Manual Page 11
Page 7
XS 600 System Menu
XS 600 System Menu
2. To activate theTilt inversion (counter-clockwise rotation) press the
UP or DOWN buttons until “On” is displayed, press ENTER to conm.
To deactivate tilt inversion, select “Off” and press Enter.
TIL2 - Tilt Inversion
1. Press the MENU button until “TIL2” is displayed, press ENTER.
Either “On” or “Off” will be displayed.
2. To activate theTilt inversion (counter-clockwise rotation) press the
UP or DOWN buttons until “On” is displayed, press ENTER to conm.
To deactivate tilt inversion, select “Off” and press Enter.
BACL - With this function you can have the LED display
turn off after 10 seconds.
1. Press the MENU button until “BACL” is displayed, press ENTER.
2. The display will show either “ON” or “OFF”. Press the UP or
DOWN buttons to select “ON” to keep the LED display on at all
times, or “OFF” to switch to have the LED display switch o after 10
seconds.
DISP - This function will reverse the display 180º.
1. Press the MENU button until “DISP” is displayed, press ENTER.
Either “On” or “Off” will be displayed.
2. To “ip” the display press the UP or DOWN buttons until “On” is
displayed, press ENTER. To activate normal display, select “Off” and
press Enter.
3. After you have pressed ENTER, use the UP and DOWN buttons
to adjust the values and test the function. To exit press the MENU
button.
HRS - With this function you can display the running time
of the unit.
1. Press the MENU button until “HRS” is displayed, press ENTER.
2. The running time of the xture will now be displayed. Press MENU
to exit.
VER - Use this function to display the Software version of
the unit.
1. Press the either the MENU button until “VER” is displayed, press
ENTER.
2. The display will show the software version.
REST - Use this function to reset the unit.
1. Press the MENU button until “REST” is displayed, press ENTER.
2. The xture will now reset.
BALA - With this function you can adjust the RGBW
colors to make your desired color.
1. Press the MENU button until “BALA” is displayed, press ENTER.
2. Use the UP or DOWN buttons to nd the color you wish to adjust.
NAN - In this submenu you are able to test the different
functions.
1. Press the MENU button until “NAN” is displayed, press ENTER.
2. Use the UP and DOWN buttons to scroll through the various functions able for testing. Once you have found your desired function you
would like to test press ENTER.
ADJ Products, LLC - www.adj.com - XS 600 User Manual Page 12 ADJ Products, LLC - www.adj.com - XS 600 User Manual Page 13
3. Once you nd the color you want to adjust press ENTER, the
displayed value will begin to ash. Use the UP or DOWN buttons to
adjust the value. Once you have made your adjustment press ENTER.
4. Repeat steps 2-3 until satised.
Page 8
XS 600 Operation XS 600 Operation
Operating Modes: The XS 600 can operate in three different
modes. In each mode you can run the fixture as a stand alone fixture
or in a master/slave confiugration. This next section will detail the dif-
ferences in the operating modes.
Universal DMX Control: This function allows you to use a univer-
sal DMX-512 controller to control the chases and patterns, dimmer
and strobe. A DMX controller allows you to create unique programs
tailored to your individual needs.
1. The XS 600 has 2 DMX Channel modes; 25 Channels, & 31
Channels. See pages 17-23 for detailed description of the DMX
values and traits.
2. To control your fixture in DMX mode, follow the set-up procedures
on pages 5-7 as well as the set-up specifications that are includ ed with your DMX controller.
3. Use the controller’s faders to control the various DMX fixture traits.
4. This will allow you to create your own programs.
5. Follow the instructions on page 9 to select your desired DMX
channel mode and to set the DMX address.
6. For longer cable runs (more than a 100 feet) use a terminator on
the last fixture.
7. For help operating in DMX mode consult the manual included
with your DMX controller.
Sound Active Mode: This mode allows either single unit or several
units linked together, to run to the beat of the music.
1. Press the MENU button until “SOND” is displayed, and press
ENTER.
2. Press the UP or DOWN button so that “ON” is displayed. The unit
will now run to the beat of the music.
3. The sound sensitivity can be adjusted by pressing the MENU
button until “SOSE” is displayed, and then press ENTER. Use the
UP or DOWN buttons to adjust the sound sensitivity, 1 being the
least sensitive, and 100 being the most sensitive.
Show Mode: In this mode you can choose 1 of 8 show modes to run.
1. Press the MENU button until
“SHND” is displayed, and press
ENTER.
2. Press the UP or DOWN buttons until you nd your desired show,
and press ENTER then press and hold MENU for 3 seconds to
con rm.
XS 600 Master-Slave Configuration
Master-Slave Operation This function will allow you to link up to
16 units together and operate without a controller. In a Master-Slave
set up one unit will act as the controlling unit and the others will react
to the controlling units programs. Any unit can act as a Master or as a
Slave.
1. Using approved DMX data cables, daisy chain your units togeth-
er via the XLR connector on the rear of the units. Remember the
Male XLR connector is the input and the Female XLR connector
is the output. The rst unit in the chain (master) will use the female
XLR connector only - The last unit in the chain will use the male
XLR connector only. For longer cable runs we suggest a termina tor at the last fixture.
2.
For the Master unit press the MENU button until “STAL” is
displayed, and press ENTER. Set the unit to “MAST” and press
ENTER.
3. Next set the Master to your desired operating mode.
4. For the slave units press the MENU button until “STAL” is dis-
played, and Press ENTER. Set the slave units to “SLAv”.
5. The slave units will now follow the Master unit.
XS 600 Power Cord Daisy Chain
With this feature you can connect the xtures to one another
using the IEC input and output sockets. The quantity that can
be connected is 8 xtures maximum After the maximum xtures
has been reached you will need to use a new power outlet. They
must be the same xtures. DO NOT mix xtures.
ADJ Products, LLC - www.adj.com - XS 600 User Manual Page 15ADJ Products, LLC - www.adj.com - XS 600 User Manual Page 14
Page 9
XS 600 UC IR Control
The UC IR infrared remote (sold separately) gives you control of various
functions. To control the fixture you must aim the remote at the front of the
fixture and be no more then 30 feet away.
The XS 600 comes with the Airstream IR remote transmitter. The ADJ
Airstream IR is a universal infrared remote control App used to control a
variety of UC IR compatiable fixtures. You can download the Airstream IR
App in the iOS App store. The remote transmitter plugs into the headphone
jack of your iOS phone or tablet. The App comes with 3 pages of control
depending on the IR fixture you are using. Additional Airstream IR transmitters are available for purchase please contact your ADJ dealer.
STAND BY - Pressing this button will blackout the fixture.
FULL ON - Hold this button down to fully light up the unit. When you let the
button go, the unit will return to its previous state.
FADE/GOBO - Press this button to enter color change mode. Press the
button a second time run color rainblow. Press this button a third time exit.
Use the Dimmer buttons to adjust the output intensity.
“DIMMER +” and “DIMMER -” - These buttons are used to adjust the output intensity.
STROBE - Press the button to activate strobing. Press the button the first
time strobe at the highest rate. Press the button a second time to strobe
at medium rate. Press the button a third time to strobe at the slowest rate.
Press the button for a fourth time to exit.
COLOR - Press this button and use buttons 1-9 to select your desired
color. See the color chart below for the numeral buttons and colors.
1-9 - When in color or show mode these buttons will allow you to select
your desired color or show.
SOUND ON & OFF - These buttons activate and deactivate the sound ac-
tive mode.
SHOW 0 - This activates the show mode. Press the Show 0 button to activate random show mode, or use buttons 1-8 to select a preset show.
BUTTON 1 2 3 4 5 6 7 8 9
HEAD1 RED GREEN BLUE WHITE RED RED(100%)
BLUE(100%)
HEAD2 RED GREEN BLUE WHITE RED(100%)
GREEN(100%)
GREEN RED(100%)
GREEN RED BLUE50%
RED100%
WHITE BLUE
GREEN(100%)
XS 600 25 Channel Mode
Channel Value Function
1 0 - 255 PAN
2 0 - 255 TILT HEAD 1
3 0 - 255 TILT HEAD 2
4 PAN CONTINUOUS ROTATION
0 - 55 NO FUNCTION
56 - 127 CLOCKWISE ROTATION
128 - 199 COUNTER-CLOCKWISE ROTATION
200 - 255 NO FUNCTION
5 PAN CONTINUOUS ROTATION SPEED
0 - 255 SLOW - FAST
6 TILT 1 CONTINUOUS ROTATION
0 - 55 NO FUNCTION
56 - 127 CLOCKWISE ROTATION
128 - 199 COUNTER-CLOCKWISE ROTATION
200 - 255 NO FUNCTION
7 TILT CONTINUOUS ROTATION SPEED
0 - 255 SLOW - FAST
8 TILT 2 CONTINUOUS ROTATION
0 - 55 NO FUNCTION
56 - 127 CLOCKWISE ROTATION
128 - 199 COUNTER-CLOCKWISE ROTATION
200 - 255 NO FUNCTION
9 TILT CONTINUOUS ROTATION SPEED
0 - 255 SLOW - FAST
10 0 - 255 HEAD 1 RED LED 0% - 100%
11 0 - 255 HEAD 1 GREEN LED 0% - 100%
12 0 - 255 HEAD 1 BLUE LED 0% - 100%
13 0 - 255 HEAD 1 WHITE LED 0% - 100%
14 0 - 255 HEAD 2 RED LED 0% - 100%
15 0 - 255 HEAD 2 GREEN LED 0% - 100%
16 0 - 255 HEAD 2 BLUE LED 0% - 100%
17 0 - 255 HEAD 2 WHITE LED 0% - 100%
18 COLOR MACROS & EFFECTS
0 - 10 NO FUNCTION
ADJ Products, LLC - www.adj.com - XS 600 User Manual Page 17ADJ Products, LLC - www.adj.com - XS 600 User Manual Page 16
Page 10
XS 600 25 Channel Mode
XS 600 25 Channel Mode
Channel Value Function
18 COLOR MACROS & EFFECTS
11 - 20 RED
21 - 30 GREEN
31 - 40 RED & GREEN
41 - 50 BLUE
51 - 60 RED & BLUE
61 - 70 GREEN & BLUE
71 - 80 RED & GREEN & BLUE
81 - 123 SINGLE COLOR CHANGE
SLOW - FAST
124 - 166 COLOR MIX SLOW - FAST
167 - 209 COLOR FADE SLOW - FAST
210 - 249 COLOR CHANGE SLOW - FAST
250 - 255 SOUND ACTIVE COLOR EFFECT
19 STROBING
0 - 7 NO STROBE
8 - 139 STROBING SLOW - FAST
140 - 189 SLOW OPEN - FAST CLOSE
190 - 231 FAST OPEN - SLOW CLOSE
240 - 255 RANDOM STROBE
20 0 - 255 MASTER DIMMER 0% - 100%
21 PROGRAMS
0 - 15 NOTHING
16 - 40 PROGRAM 1
41 - 65 PROGRAM 2
66 - 90 PROGRAM 3
91 - 115 PROGRAM 4
116 - 140 PROGRAM 5
141 - 165 PROGRAM 6
166 - 190 PROGRAM 7
191 - 215 PROGRAM 8
216 - 240 RANDOM PROGRAM PLAYING 5
TIMES EACH
241 - 255 RANDOM PROGRAM 2 MINS. EACH
Channel Value Function
22 0 - 255 PROGRAM SPEED SLOW - FAST
23 0 - 255 PAN/TILT SPEED FAST - SLOW
24 SPECIAL FUNCTIONS
0 - 69 NO FUNCTION
70 - 79 BLACKOUT WITH PAN/TILT
MOVEMENT
80 - 89 NO FUNCTION
90 - 99 BLACKOUT WITH RGBW VALUE
CHANGES
100 - 199 NO FUNCTION
200 - 209 RESET ALL
210 - 255 NO FUNCTION
25 DIMMER MODE
0 - 20 STANDARD
21 - 40 STAGE
41 - 60 TV
61 - 80 ARCHITECTURAL
81 - 100 THEATRE
101 - 255 DEFAULT DIMMER SETTING
ADJ Products, LLC - www.adj.com - XS 600 User Manual Page 19ADJ Products, LLC - www.adj.com - XS 600 User Manual Page 18
Page 11
XS 600 31 Channel Mode
XS 600 31 Channel Mode
Channel Value Function
1 0 - 255 PAN
2 0 - 255 PAN FINE
3 0 - 255 TILT HEAD 1
4 0 - 255 TILT FINE HEAD 1
5 0 - 255 TILT HEAD 2
6 0 - 255 TILT FINE HEAD 2
7 PAN CONTINUOUS ROTATION
0 - 55 NO FUNCTION
56 - 127 CLOCKWISE ROTATION
128 - 199 COUNTER-CLOCKWISE ROTATION
200 - 255 NO FUNCTION
8 PAN CONTINUOUS ROTATION SPEED
0 - 255 SLOW - FAST
9 TILT 1 CONTINUOUS ROTATION
0 - 55 NO FUNCTION
56 - 127 CLOCKWISE ROTATION
128 - 199 COUNTER-CLOCKWISE ROTATION
200 - 255 NO FUNCTION
10 TILT CONTINUOUS ROTATION SPEED
0 - 255 SLOW - FAST
11 TILT 2 CONTINUOUS ROTATION
0 - 55 NO FUNCTION
56 - 127 CLOCKWISE ROTATION
128 - 199 COUNTER-CLOCKWISE ROTATION
200 - 255 NO FUNCTION
12 TILT CONTINUOUS ROTATION SPEED
0 - 255 SLOW - FAST
13 0 - 255 HEAD 1 RED LED 0% - 100%
14 0 - 255 HEAD 1 GREEN LED 0% - 100%
15 0 - 255 HEAD 1 BLUE LED 0% - 100%
16 0 - 255 HEAD 1 WHITE LED 0% - 100%
17 0 - 255 HEAD 2 RED LED 0% - 100%
18 0 - 255 HEAD 2 GREEN LED 0% - 100%
19 0 - 255 HEAD 2 BLUE LED 0% - 100%
ADJ Products, LLC - www.adj.com - XS 600 User Manual Page 20 ADJ Products, LLC - www.adj.com - XS 600 User Manual Page 21
Channel Value Function
20 0 - 255 HEAD 2 WHITE LED 0% - 100%
21 HEAD 1 COLOR MACROS & EFFECTS
0 - 10 NO FUNCTION
11 - 20 RED
21 - 30 GREEN
31 - 40 RED & GREEN
41 - 50 BLUE
51 - 60 RED & BLUE
61 - 70 GREEN & BLUE
71 - 80 RED & GREEN & BLUE
81 - 123 SINGLE COLOR CHANGE
SLOW - FAST
124 - 166 COLOR MIX SLOW - FAST
167 - 209 COLOR FADE SLOW - FAST
210 - 249 COLOR CHANGE SLOW - FAST
250 - 255 SOUND ACTIVE COLOR EFFECT
22 HEAD 2 COLOR MACROS & EFFECTS
0 - 10 NO FUNCTION
11 - 20 RED
21 - 30 GREEN
31 - 40 RED & GREEN
41 - 50 BLUE
51 - 60 RED & BLUE
61 - 70 GREEN & BLUE
71 - 80 RED & GREEN & BLUE
81 - 123 SINGLE COLOR CHANGE
SLOW - FAST
124 - 166 COLOR MIX SLOW - FAST
167 - 209 COLOR FADE SLOW - FAST
210 - 249 COLOR CHANGE SLOW - FAST
250 - 255 SOUND ACTIVE COLOR EFFECT
23 STROBING HEAD 1
0 - 7 NO STROBE
8 - 139 STROBING SLOW - FAST
Page 12
XS 600 31 Channel Mode
XS 600 31 Channel Mode
Channel Value Function
23 STROBING HEAD 1
140 - 189 SLOW OPEN - FAST CLOSE
190 - 231 FAST OPEN - SLOW CLOSE
240 - 255 RANDOM STROBE
24 STROBING HEAD 2
0 - 7 NO STROBE
8 - 139 STROBING SLOW - FAST
140 - 189 SLOW OPEN - FAST CLOSE
190 - 231 FAST OPEN - SLOW CLOSE
240 - 255 RANDOM STROBE
25 0 - 255 MASTER DIMMER HEAD 1 0% - 100%
26 0 - 255 MASTER DIMMER HEAD 2 0% - 100%
27 PROGRAMS
0 - 15 NOTHING
16 - 40 PROGRAM 1
41 - 65 PROGRAM 2
66 - 90 PROGRAM 3
91 - 115 PROGRAM 4
116 - 140 PROGRAM 5
141 - 165 PROGRAM 6
166 - 190 PROGRAM 7
191 - 215 PROGRAM 8
216 - 240 RANDOM PROGRAM PLAYING 5
TIMES EACH
241 - 255 RANDOM PROGRAM 2 MINS. EACH
28 0 - 255 PROGRAM SPEED SLOW - FAST
29 0 - 255 PAN/TILT SPEED FAST - SLOW
30 SPECIAL FUNCTIONS
0 - 69 NO FUNCTION
70 - 79 BLACKOUT WITH PAN/TILT
MOVEMENT
80 - 89 NO FUNCTION
90 - 99 BLACKOUT WITH RGBW VALUE
CHANGES
Channel Value Function
30 SPECIAL FUNCTIONS
100 - 199 NO FUNCTION
200 - 209 RESET ALL
210 - 255 NO FUNCTION
31 DIMMER MODE
0 - 20 STANDARD
21 - 40 STAGE
41 - 60 TV
61 - 80 ARCHITECTURAL
81 - 100 THEATRE
101 - 255 DEFAULT DIMMER SETTING
ADJ Products, LLC - www.adj.com - XS 600 User Manual Page 23ADJ Products, LLC - www.adj.com - XS 600 User Manual Page 22
Page 13
XS 600 Photometric Chart
XS 600 Dimmer Curve Chart
XS 600 Fuse Replacement
Disconnect the unit from its power source. Remove the power cord
from the unit. The fuse holder is located next to the power supply
input. Use a phillips head screw driver to unscrew the fuse holder.
Remove the bad fuse and replace with a new one.
XS 600 Cleaning
Fixture Cleaning: Due to fog residue, smoke, and dust cleaning
the internal and external optical lenses and mirror should be carried
out periodically to optimize light output. Cleaning frequency depends
on the environment in which the fixture operates (I.e. smoke, fog
residue, dust, dew). In heavy club use we recommend cleaning on a
monthly basis. Periodic cleaning will ensure longevity, and crisp output.
1. Use normal glass cleaner and a soft cloth to wipe down the out-
side casing.
2. Use a brush to wipe down the cooling vents and fan grill.
3. Clean the external optics and mirror with glass cleaner and a soft
cloth every 20 days.
4. Clean the internal optics with glass cleaner and a soft cloth every
30-60 days.
5. Always be sure to dry all parts completely before plugging the unit
back in.
Ramp Effect
Standard
Stage
TV
Architectural
Theatre
XS 600 Trouble Shooting
Trouble Shooting: Listed below are a few common problems that
(Fade Time) (Fade Time)
you may encounter, with solutions.
No light output from the unit;
1. Be sure the external fuse has not blown. The fuse is located on
the rear panel of the unit.
2. Be sure the fuse holder is completely and properly seated.
Unit does not respond to sound;
1. Low frequencies (bass) should cause the unit to react to sound.
Tapping on the microphone, quiet or high pitched sounds may
not activate the unit.
2. Check the sound sensitivity level. Make sure it is not set to a low
sensitivity level.
ADJ Products, LLC - www.adj.com - XS 600 User Manual Page 24 ADJ Products, LLC - www.adj.com - XS 600 User Manual Page 25
Page 14
XS 600 Warranty
MANUFACTURER’S LIMITED WARRANTY
A. ADJ Products, LLC hereby warrants, to the original purchaser, ADJ Products, LLC products
to be free of manufacturing defects in material and workmanship for a prescribed period from
the date of purchase (see specific warranty period on reverse). This warranty shall be valid only if the
product is purchased within the United States of America, including possessions and
territories. It is the owner ’s responsibility to establish the date and place of purchase by acceptable
evidence, at the time service is sought.
B. For warranty service you must obtain a Return Authorization number (RA#)
before sending back the product–please contact ADJ Products, LLC Service Department
at 800-322-6337. Send the product only to the ADJ Products, LLC factory. All
shipping charges must be pre-paid. If the requested repairs or service (including
parts replacement) are within the terms of this warranty, ADJ Products, LLC will pay return
shipping charges only to a designated point within the United States. If the entire instrument is
sent, it must be shipped in it’s original package. No accessories should be shipped with the product. If
any accessories are shipped with the product, ADJ Products, LLC shall have no liability whatsoever for
loss of or damage to any such accessories, nor for the safe return thereof.
C. This warranty is void if the serial number has been altered or removed; if the product is modified in any
manner which ADJ Products, LLC concludes, after inspection, affects the reliability of the product; if the
product has been repaired or serviced by anyone other than the ADJ Products, LLC factory unless prior
written authorization was issued to purchaser by ADJ Products, LLC; if the product is damaged because
not properly maintained as set forth in the instruction manual.
D. This is not a service contract, and this warranty does not include maintnance, cleaning or periodic check
up. During the period specified above, ADJ Products, LLC will replace defective parts at its expense
with new or refurbished parts, and will absorb all expenses for warranty service and repair labor by
reason of defects in material or workmanship. The sole responsibility of ADJ Products, LLC under this
warranty shall be limited to the repair of the product, or replacement thereof, including parts, at the sole
discretion of ADJ Products, LLC. All products covered by this warranty were manufactured after August
15, 2012, and bear indentifying marks to that effect.
E. ADJ Products, LLC reserves the right to make changes in design and/or improvements upon its products
without any obligation to include these changes in any products theretofore manufactured.
No warranty, whether expressed or implied, is given or made with respect to any accessory supplied with
products described above. Except to the extent prohibited by applicable law, all implied warranties made
by ADJ Products, LLC in connection with this product, including warranties of merchantability or fitness,
are limited in duration to the warranty period set forth above. And no warranties, whether expressed or
implied, including warranties of merchantability or fitness, shall apply to this product after said period
has expired. The consumer’s and/or Dealer’s sole remedy shall be such repair or replacement as is
expressly provided above; and under no circumstances shall ADJ Products, LLC be liable for any loss or
damage, direct or consequential, arising out of the use of, or inability to use, this product.
This warranty is the only written warranty applicable to ADJ Products, LLC Products and
supersedes all prior warranties and written descriptions of warranty terms and conditions heretofore
published.
MANUFACTURER’S LIMITED WARRANTY PERIODS:
•LightingProducts=1-year(365days)LimitedWarranty(Such as: Special Effect Lighting, Intelligent
Lighting, UV lighting, Strobes, Fog Machines, Bubble Machines, Mirror Balls, Par Cans, Trussing,
Lighting Stands etc. excluding LED and lamps)
•LaserProducts=1Year(365Days)LimitedWarranty(excluding laser diodes which have a 6 month
limited warranty)
•L.E.D.Products=2-year(730days)LimitedWarranty(excluding motors, PCB boards, and power
supplies, which have a 1-year (365 day Limited Warranty) batteries which have a 180 day limited war-
ranty). Only the L.E.D.s carry a 2-year warranty (excludingStarTecSerieswhichacarriesa1Year
LimitedWarranty)Note:2YearWarrantyonlyappliestopurchaseswithintheUnitedStates.
•ADJDMXControllers=2Year(730Days)LimitedWarranty(excluding faders and tact switches)
ADJ Products, LLC - www.adj.com - XS 600 User Manual Page 26
XS 600 Specifications
Model: XS 600
Voltage: 100V ~ 240V/50~60Hz
LEDs: 6 x 10W RGBW 4-in-1 LEDs
Power Consumption: 60W
Power Cord Daisy Chain: 8 Fixtures Max.
Beam Angle: 5 Degrees
Dimensions: 7.75”(L) x 5”(W) x 12.5”(H)
196 x 126 x 318mm
Weight: 7 Lbs. / 3 kgs.
Colors: RGBW Color Mixing
Fuse: 1A
Duty Cycle: None
DMX Modes: 2 DMX Channel Modes: 21 Channel
Mode & 31 DMX Channels
Working Position: Any Safe, Secure Position
Warranty: 2 Year (730 days)
Auto Sensing Voltage: This xture contains a automatic volt-
age switch, which will auto sense the voltage when it is plugged
into the power source.
Please Note: Specications and improvements in the design
of this unit and this manual are subject to change without any
prior written notice.
ADJ Products, LLC
6122 S. Eastern Ave. Los Angeles, CA 90040 USA
Tel: 323-582-2650 / Fax: 323-725-6100
Web: www.adj.com / E-mail: info@americandj.com
A.D.J. Supply Europe B.V.
Junostraat 2
6468 EW Kerkrade
The Netherlands
service@adjgroup.eu / www.adj.eu
Tel: +31 45 546 85 00 / Fax: +31 45 546 85 99
Loading...