ADJ VS3 Indoor LED Panel, VS2 Indoor LED Panel User Manual [EN]

©2020 ADJ PRODUCTS LLC all rights reserved. Information, specifications, diagrams, images, and instructions herein

Date

Document Version

Notes

02/25/20 1 Initial Release

are subject to change without notice. ADJ logo and identifying product names and numbers herein are trademarks of ADJ
PRODUCTS LLC. Copyright protection claimed includes all forms and matters of copyrightable materials and in- formation
now allowed by statutory or judicial law or hereinafter granted. Product names used in this document may be trademarks
or registered trademarks of their respective companies and are hereby acknowledged. All non-ADJ brands and product
names are trademarks or registered trademarks of their respective companies.

ADJ PRODUCTS LLC and all affiliated companies hereby disclaim any and all liabilities for property, equipment, building,
and electrical damages, injuries to any persons, and direct or indirect economic loss associated with the use or reliance
of any information contained within this document, and/or as a result of the improper, unsafe, insufficient and negligent
assembly, installation, rigging, and operation of this product.

ADJ PRODUCTS LLC USA

6122 S. Eastern Ave. Los Angeles, CA 90040
323-582-2650 | Fax [phone] | www.adj.com | [e-mail]

ADJ SUPPLY Europe B.V

Junostraat 2 6468 EW Kerkrade, The Netherlands
[phone] | Fax [phone] | www.adj.eu | [e-mail]

ADJ PRODUCTS GROUP Mexico

AV Santa Ana 30 Parque Industrial Lerma, Lerma, Mexico 52000
[phone] | [e-mail]

FCC STATEMENT

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device
may not cause harmful interference, and (2) this device must accept any interference received, including interference that
may cause undesired operation.

FCC RADIO FREQUENCY INTERFERENCE WARNINGS & INSTRUCTIONS

This product has been tested and found to comply with the limits as per Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential installation. This device uses and can radiate
radio frequency energy and, if not installed and used in accordance with the included instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this device does cause harmful interference to radio or television reception, which can be deter- mined by
turning the device off and on, the user is encouraged to try to correct the interference by one or more of the following
methods:

- Reorient or relocate the device.

- Increase the separation between the device and the receiver.

- Connect the device to an electrical outlet on a circuit different from which the radio receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

Energy Saving Matters (EuP 2009/125/EC)

Saving electric energy is a key to help protecting the environment. Please turn off all electrical products when they are not
in use. To avoid power consumption in idle mode, disconnect all electrical equipment from power when not in use. Thank
you!
Document Version: An updated version of this document may be available online. Please check www.adj.com for the latest
revision/update of this document before beginning installation and use.

3

CONTENTS

General Information

4

Limited Warranty (USA Only)

5

Safety Guidelines

6

Maintenance Guidelines

8

Panel Overview

9

Receiver-Card Module Removal

11

Handling and Transportation

13

Installation

15

Technical Specifications

27

Optional Components and Accessories

28

ADJ Products, LLC • Los Angeles, Ca USA • Kerkrade, The Netherlands

4

GENERAL INFORMATION

INTRODUCTION

Please read and understand the instructions in this manual carefully and thoroughly before attempting
to operate this device. These instructions contain important safety and use information.

ADJ’s Vision Series LED Video Panels offer the highest quality LED binning using 3-in-1 RGB
SMD2121 LEDs, with a brightness of 1000 NITS. The only difference between models is the pixel
pitch: the VS2 has a pixel pitch of 2.97mm, the VS3 has a pixel pitch of 3.91mm, and the VS5 has a
pixel pitch of 5.95mm. Otherwise, all models have 4 individual modules for quick and easy front and
rear accessible servicing; are built on the same frame, which allows panels with different resolutions
to be used together; use the same rigging bar; all fit into the same road case; and all have moveable
integrated Corner Protectors that safe-guard the corners when they are not connected. In addition,
each Vision Series LED Video Panel model has magnets located at the top and bottom to allow users
to temporarily connect two panels, let go, and then securely latch them on the rear. This allows a
single-user to install a full wall of panels.

The VS Vision Series LED Video Panel connections include PowerLock In/Out and DataLock In/Out,
and feature built-in Novastar A5s receiving card. An optional VSFC8 Flight Case (purchased
separately) can carry up to 8x VS LED Video Panels, and an optional VSRB1 Rigging Bar (purchased
separately) can hang up to 20 VS LED Video Panels vertically.

ADJ offers full packages with video processors, software, cabling, rigging bars and flight cases so that
you have everything you need to get up and running.

UNPACKING

Every VS LED Video Panel has been thoroughly tested and has been shipped in perfect operating
condition. Carefully check the shipping carton for damage that may have occurred during shipping. If
the carton is damaged, carefully inspect the device for damage, and be sure all accessories necessary
to install and operate the device have arrived intact. In the event damage has been found or parts are
missing, please contact our customer support team for further instructions. Please do not return this
device to your dealer without first contacting customer support. Please do not discard the shipping
carton in the trash. Please recycle whenever possible.

CUSTOMER SUPPORT

Contact ADJ Service for any product related service and support needs.
Also visit forums.adj.com with questions, comments or suggestions.

ADJ SERVICE USA - Monday - Friday 8:00am to 4:30pm PST
323-582-2650 | Fax: [phone] | [e-mail]

ADJ SERVICE EUROPE - Monday - Friday 08:30 to 17:00 CET
[phone] | Fax: [phone] | [e-mail]

ADJ Products, LLC • Los Angeles, Ca USA • Kerkrade, The Netherlands

5

LIMITED WARRANTY

A. ADJ Products, LLC hereby warrants, to the original purchaser, ADJ Products, LLC products to be free of

manufacturing defects in material and workmanship for a prescribed period from the date of purchase (see specific
warranty period on reverse). This warranty shall be valid only if the product is purchased within the United States of
America, including possessions and territories. It is the owner’s responsibility to establish the date and place of
purchase by acceptable evidence, at the time service is sought.

B. For warranty service, you must obtain a Return Authorization number (RA#) before sending the product back—please

contact ADJ Products, LLC Service Department at 800-322-6337. Send the product only to the ADJ Products, LLC
factory. All shipping charges must be prepaid. If the requested repairs or service (including parts replacement) are
within the terms of this warranty, ADJ Products, LLC will pay return shipping charges only to a designated point within
the United States. If the entire instrument is sent, it must be shipped in its original package and packaging material.
No accessories should be shipped with the product. If any accessories are shipped with the product, ADJ Products,
LLC shall incur no liability whatsoever for loss of or damage to any such accessories, nor for the safe return thereof.

C. This warranty is void if the product serial number and/or labels are altered or removed; if the product is modified in

any manner which ADJ Products, LLC concludes, after inspection, affects the reliability of the product; if the product
has been repaired or serviced by anyone other than the ADJ Products, LLC factory unless prior written authorization
was issued to purchaser by ADJ Products, LLC; if the product is damaged because it was not properly maintained
as set forth in the product instructions, guidelines and/or user manual.

D. This is not a service contract, and this warranty does not include maintenance, cleaning, or periodic checkup. During

the period specified above, ADJ Products, LLC will replace defective parts at its expense with new or refurbished
parts, and will absorb all expenses for warranty service and repair labor by reason of defects in material or
workmanship. The sole responsibility of ADJ Products, LLC under this warranty shall be limited to the repair of the
product, or replacement thereof, including parts, at the sole discretion of ADJ Products, LLC. All products covered
by this warranty were manufactured after August 15, 2012, and bear identifying marks to that effect.

E. ADJ Products, LLC reserves the right to make changes in design and/or improvements upon its products without any

obligation to include these changes in any products theretofore manufactured.

F. No warranty, whether expressed or implied, is given or made with respect to any accessory supplied with products

described above. Except to the extent prohibited by applicable law, all implied warranties made by ADJ Products,
LLC in connection with this product, including warranties of merchantability or fitness, are limited in duration to the
warranty period set forth above. And all warranties, whether expressed or implied, including warranties of
merchantability or fitness, are limited in duration to the warranty period set forth above. The consumer’s and/or
dealer’s sole remedy shall be such repair or replacement as is expressly provided above; and under no circumstances
shall ADJ Product, LLC be liable for any loss and/or damage, direct and/or consequential arising out of the use of,
and/or inability to use this product.

G. This warranty is the only written warranty applicable to ADJ Products, LLC products, and supersedes all prior

warranties and written descriptions of warranty terms and conditions heretofore published.

MANUFACTURER’S LIMITED WARRANTY PERIODS:

Non-LED Lighting Products = 1-Year (365 Days) (Including Special Effect Lighting, Intelligent Lighting, UV lighting, Strobes, Fog
Machines, Bubble Machines, Mirror Balls, Par Cans, Trussing, Lighting Stands, Power/Data Distribution, etc. excluding LED and lamps)

Laser Products = 1-Year (365 Days) (excluding laser diodes which have a 6-Month Limited Warranty)
LED Products = 2-Year (730 Days) (excluding batteries which have a 180 Day Limited Warranty)
NOTE: 2-Year (730 Days) Limited Warranty ONLY applies to product purchased within the United States.
StarTec Series = 1-Year (365 Days) (excluding batteries which have a 180 Day Limited Warranty)
ADJ DMX Controllers = 2 Year (730 Days)
American Audio Products = 1 Year (365 Days)

CUSTOMER SUPPORT INFORMATION

Contact ADJ Service for any product related service and support needs.
Also visit forums.adj.com with questions, comments or suggestions.

ADJ SERVICE USA - Monday - Friday 8:00am to 4:30pm PST
323-582-2650 | Fax: [phone] | [e-mail]

ADJ SERVICE EUROPE - Monday - Friday 08:30 to 17:00 CET
[phone] | Fax: [phone] | [e-mail]

ADJ Products, LLC • Los Angeles, Ca USA • Kerkrade, The Netherlands

6

SAFETY GUIDELINES

This VS LED Video Panel is a sophisticated piece of electronic equipment. To guarantee a smooth operation, it is important
to follow all instructions and guidelines in this manual. ADJ is not responsible for injury and/or damages resulting from the
misuse of this panel due to the disregard of the information printed in this manual. Only qualified and/or certified personnel
should perform the installation of this panel and all included and/or rigging accessories. Only the original included rigging
parts and/or rigging accessories for this panel should be used for proper installation. Any modifications to the panel,
included and/or rigging accessories will void the original manufactures warranty and increase the risk of damage and/or
personal injury.

PROTECTION CLASS 1 - PANEL MUST BE PROPERLY GROUNDED.

THERE ARE NO USER SERVICEABLE PARTS INSIDE THIS PANEL.

DO NOT ATTEMPT ANY REPAIRS YOURSELF; DOING SO WILL VOID YOUR MANUFACTURES
WARRANTY. DAMAGES RESULTING FROM MODIFICATIONS TO THIS PANEL AND/OR THE
DISREGARD OF SAFETY INSTRUCTIONS AND GUIDELINES IN THIS MANUAL VOID THE
MANUFACTURES WARRANTY AND ARE NOT SUBJECT TO ANY WARRANTY CLAIMS AND/OR
REPAIRS. DO NOT PLUG PANEL INTO A DIMMER PACK! NEVER OPEN THIS PANEL WHILE IN USE!
UNPLUG POWER BEFORE SERVICING PANEL! NEVER TOUCH FRONT OF PANEL DURING OPERATION,
AS IT MAY BE HOT! KEEP FLAMMABLE MATERIALS AWAY FROM PANEL.

INDOOR / DRY LOCATIONS USE ONLY!
DO NOT EXPOSE PANEL TO RAIN AND/OR MOISTURE!
DO NOT SPILL WATER AND/OR LIQUIDS ON OR INTO THE PANEL!

DO NOT touch panel housing during operation. Turn OFF power and allow approximately 15 minutes for panel to cool

down before servicing.

DO NOT: Operate a panel if any cover is open and/or removed.

DO NOT shake panel, avoid brute force when installing and/or operating panel.

DO NOT: Expose any part of the panel to open flame or smoke. Keep panel away from heat sources such as radiators,

heat registers, stoves, or other appliances (including amplifiers) that produce heat.

DO NOT: Install/use panel in extreme hot/humid environments, or handle without ESD precautions.

DO NOT: Exceed an operation temperature of 40°C (104°F), doing so will damage the panel.

DO NOT operate panel if power cord is frayed, crimped, damaged and/or if any of the power cord connectors are damaged

and do not insert into the panel securely with ease. NEVER force a power cord connector into the panel. If the power cord
or any of its connectors are damaged, replace it immediately with a new one of similar power rating.

DO NOT block air ventilation slots/vents. All fan and air inlets must remain clean and never blocked.
Allow approximately 6” (15cm) between panel and other devices or a wall for proper cooling.

ALWAYS disconnect panel from main power source before performing any type of service and/or cleaning procedure.
Only handle the power cord by the plug end, never pull out the plug by tugging the wire portion of the cord.

ADJ Products, LLC • Los Angeles, Ca USA • Kerkrade, The Netherlands

7

SAFETY GUIDELINES

ONLY use the original packaging materials and/or case to transport the panel in for service.

PLEASE recycle shipping boxes and packaging whenever possible.

CAUTION: To avoid physical damage, read the installation instructions carefully before installation.

CAUTION: Panels should only be installed/operated by qualified and trained professionals ONLY.

CAUTION: Always mount panels in a safe and stable manner.

CAUTION: INDOOR / DRY location use ONLY! Outdoor use will void the warranty.

CAUTION: Wear appropriate safety equipment during panel installation.

CAUTION: Turn OFF power to panel, computers, servers, system boxes, and monitors before making any type

of power or data connections and performing any maintenance work.

CAUTION: Read user manual carefully to ensure normal operation and lifespan of the panel.

CAUTION: Electronics used in this panel are ESD (Electrostatic Discharge) sensitive. To protect device from

ESD, wear a grounded ESD wrist strap or similar grounding device when handling panel.

CAUTION: Panel must be properly grounded before operating. (resistance must be less than 4Ω)

CAUTION: Ensure all power is disconnected from panel before unplugging any data cables from the panel,

especially serial line ports.

CAUTION: Route power and data cables so that they are NOT likely to be walked on or pinched.

CAUTION: Air conditioning is required if operating environment temperature exceeds 30°C (86°F).

CAUTION: Test panel for 2-hours per week, if not used regularly or for an extended period of time.

CAUTION: Cases used to transport panel must me properly waterproofed for transportation.

ADJ Products, LLC • Los Angeles, Ca USA • Kerkrade, The Netherlands

8

MAINTENANCE GUIDELINES

Careful and regular maintenance is necessary to optimize the potential functional lifespan of the VS
LED Video Panels.

1. Read the installation and operation instructions for correct operation of the VS LED Video Panels.

2. Although the VS LED Video Panels are designed and built to withstand some impact forces when
installed correctly, take care to avoid impact damage when handling or transporting them,
especially corners and edges, which are particularly frangible during transportation.

3. The fixture should be serviced by a qualified service technician when:

A. Objects have fallen, or liquid has been spilled into the fixture
B. The fixture has been exposed to rain or water conditions in excess of IP rating parameters

(IP20 front and rear)
C. The fixture does not appear to operate normally or exhibits a marked change in performance
D. The fixture has fallen and/or subjected to extreme handling.

4. Check each VS LED Video Panel for loose screws and other fasteners.

5. If the VS LED Video Panel installation is fixed or displayed for a lengthy time, regularly inspect all
rigging and installation equipment, and replace or repair it as necessary, and during long periods

of non-use, disconnect the main power to the unit.

6. Use necessary ESD (electrostatic discharge) precautions when handling VS LED Video Panels,
especially the LED screens, as they are ESD sensitive and easily damaged from ESD exposure.

7. The Null Line and Live Line connections from the computer and control system cannot be reversed
and should therefore only be connected in original layout order.

8. If the GFI (Ground Fault Interrupt) breaker-switch trips often, check the display or replace the
power-supply switch.

9. When operating the VS LED Video Panels, power the computer before powering the LED Video
Screens; conversely, when shutting down after operation, turn the LED Video Panels off before
turning off the computer. If the PC is turned off first, a high intensity brightness might appear,
causing catastrophic failure to those LEDs.

10. If while conducting an electrical test a circuit shorts, a breaker-switch trips, wires burn, and or any
other abnormality appears, discontinue testing and troubleshoot units to find the problem before
continuing with any testing or operation.

11. To ensure consistent operation, it might be necessary to learn operating parameters for
installation, data recovery, backup, controller settings, and basic data preset modification.

12. Regularly check computer for any viruses and remove any irrelevant data.

13. Only a qualified technician should operate software system.

14. Remove any moisture found inside or outside of any VS LED Video Panels before dismantling
video installation and returning them to their optional flight cases (sold separately). Ensure flight
cases are free of any moisture, using a fan to dry them if necessary, and avoid ESD generating
friction when returning VS LED Video Panels.

15. The VS LED Video Panels are designed for indoor use only, within its IP20 rating parameters (front
/ rear), limit or remove any unit exposed to moisture, condensation, or humidity, and consider
using air conditioning where available.

16. When not in use, store VS LED Video Panels in a dry, well ventilated facility.

ADJ Products, LLC • Los Angeles, Ca USA • Kerkrade, The Netherlands

9

PANEL OVERVIEW

Folding Handle

Integrated Vertical Locking
Panel Connector

Integrated Horizontal
Locking Panel Connector

Locking RJ45 Ethernet
Connect In/Out/RJ45

Power Output (-)

Power Input (+)

ESD Grounding Hole &
Connection Plate

Integrated Corner Protectors

19.68” (500mm)

19.68”

2.74” (69.9mm)

Dimensions: 19.75” x 19.75” x 3” (500x500x100mm)

ADJ Products, LLC • Los Angeles, Ca USA • Kerkrade, The Netherlands

10

PANEL OVERVIEW

19.68” (500mm)

19.68”

Note that panels
and power supply
cover are all
attached with
safety cables.

k

Each VS LED Video Panel includes a quick-release power supply with 4X LED Modules, allowing for
easy serviceability and simple repairs whilst out on the road, and each is held safely in place with
frame integrated magnets. The cover of the power supply box can be secured to protect all internal
accessories and components. All detachable component is secured with a safety cable.

V

ADJ Products, LLC • Los Angeles, Ca USA • Kerkrade, The Netherlands

11

RECEIVER-CARD MODULE REMOVAL

A technician can use the optional VSM111 Magnetic
Module Removal Tool (sold separately) to safely remove

and reinstall any of the four Receiver-Card Modules in the
VS LED Video Panel, and minimize potential damage from
mishandling, ESD exposure, or other issues.

The percieved “Magnetic Force” is relative to the distance the magnet is from the surface. Turning
the knob clockwise, in the “+” direction, advances the magnet, moving it closer to the front, and
turning it counterclockwise, in the “-” direction, retracts the magnet, moving it away from the front.

The magnet must be fully retracted in the Magnet Module Removal Tool before placing it
against the Receiver-Card Module face, which is to prevent the magnet from snapping
against the LEDs and damaging them.

Rubber O-Ring

ADJ Products, LLC • Los Angeles, Ca USA • Kerkrade, The Netherlands

12

RECEIVER-CARD MODULE REMOVAL

Note that the Receiver-Card Modules are firmly held to the VS LED Video Panel Frame with strong
integrated magnets, and secured with a safety cable should any of the panel modules be accidently
knocked free.

Locate the center of quarter panel module and place the O-Ring of the Magnetic Module Removal

Tool against its surface.

Turn the knob at the rear of the Magnetic Module Removal Tool to advance the magnet to secure
the Receiver-Card Module. When placed against the surface of the Reciever-Card Module (the
Magnetic Module Removal Tool magnet is stronger than those that hold the Reciever-Card Module
to the VS LED Video Panel frame, which allows it to pull the module from the frame). With it secured,
carefully pull the module free from the video panel frame. When finished servicing the Reciever-Card
Module, reverse the operation. Be sure to reattach the safety cable to the Reciever-Card Module.

ADJ Products, LLC • Los Angeles, Ca USA • Kerkrade, The Netherlands

13

HANDLING AND TRANSPORTATION

The Integrated corner protectors
rotate into their respective pockets for
adjacent panel installation, or out of
their pockets to protect the corners
during transportation or storage.

VS LED Video Panels
are susceptible to
damage at corners.

The corners of the VS LED Video Panel are susceptible to damage during handling and transportation.
When removing VS LED Video Panels from their respective Flight Cases (VSFC8 sold separately), and
before they are installed, take care to avoid damaging any of the 4 corners.

Because these are ESD sensitive units, use ESD precautions when removing the VS LED Video Panels
from their flight case (ESD gloves, protective clothing, wrist straps, etc.). In addition to using standard
ESD precautions, to reduce static building friction, take care to lift the panels without rubbing the LED
panel surface along the foam-covered slots, which can generate static electricity that can damage
LEDs on VS LED Video Panels.

ADJ Products, LLC • Los Angeles, Ca USA • Kerkrade, The Netherlands

14

HANDLING AND TRANSPORTATION

The optional VSFC8 Flight Case (sold separately) for the VS LED Video Panels holds 8x VS LED
VIDEO PANELs. The flight case features a full foam lining with slots for each unit. The case is robust,

so will completely protect a set of panels on the road. Designed specifically for use with VS LED Video
Panels, it is constructed from 9mm plywood and fitted with steel ball corners, aluminum edging, large
swivel castors, professional butterfly latches, four sprung handles, and a hinged lid.

VSFC8 Flight Case

ADJ Products, LLC • Los Angeles, Ca USA • Kerkrade, The Netherlands

15

INSTALLATION

Input Power

AC 100-240VAC, 50/60HZ, 16A Max

Output Power

AC 100-240VAC, 50/60Hz, 14A Max

Max Power Consumption

170W Max, 68W Average

DO NOT INSTALL THE PANEL IF YOU ARE NOT QUALIFIED TO DO SO!
INSTALLATION BY QUALIFIED TECHNICIANS ONLY!

INSTALLATIONS SHOULD BE CHECKED BY A QUALIFIED PERSON ONCE A YEAR!

FLAMMABLE MATERIAL WARNING
Keep panel minimum 5.0 feet (1.5m) away from flammable materials and/or pyrotechnics.

ELECTRICAL CONNECTIONS
A qualified electrician should be used for all electrical connections and/or installations.

A MAXIMUM OF 20 panels may be suspended from each other vertically in a curtain.
An unlimited number of panels may be installed horizontally.
(NOTE: Additional processing may be necessary)

USE CAUTION WHEN POWER LINKING MULTIPLE PANELS AS THE POWER CONSUMPTION
OF OTHER PANEL MODELS MAY EXCEED THE MAX POWER OUTPUT ON THIS PANEL.
CHECK SILK SCREEN FOR MAX AMPS.

WARNING! The safety and suitability of any lifting equipment, installation location/platform,

anchoring/rigging/mounting method and hardware, and electrical installation is the sole responsibility of
the installer.

Panel(s) and all panel accessories and all anchoring/rigging/mounting hardware MUST be installed
following all local, national, and country commercial electrical and construction codes and regulations.

Before rigging/mounting a single panel or multiple interconnected panels to any metal truss/structure, a
professional equipment installer MUST be consulted to determine if the metal truss/structure or surface is
properly certified to safely hold the combined weight of the panels(s), clamps, cables, and all accessories.

Inspect metal truss/structure visually to ensure it does not flex and/or become deformed due to the weight
of the panel(s). Damage caused to panel(s) by mechanical stress is not covered by warranty.

Panel(s) should be installed in areas outside walking paths, seating areas, or away from areas were
unauthorized personnel might reach the panel(s) by hand. Access under work area must be blocked.

NEVER stand directly below the panel(s) when rigging, removing or servicing.

OVERHEAD RIGGING

Overhead fixture installation must always be secured with a secondary safety attachment, such as an
appropriately rated safety cable. Overhead rigging requires extensive experience, including amongst
others calculating working load limits, installation material being used, and periodic safety inspection of all
installation material and the fixture. If you lack these qualifications, do not attempt the installation yourself.
Improper installation can result in bodily injury and property damage.

ADJ Products, LLC • Los Angeles, Ca USA • Kerkrade, The Netherlands

16

INSTALLATION – ASSEMBLY

The horizontal tab-keyed connector is spring
loaded.

Press the horizontal tab-keyed connector until its
tab-key passes through tab-keyed socket.

Rotate the handle to the right (clockwise) to hold
the horizontal tab-keyed connector in place.

Rotate handle down (counterclockwise) to cinch
horizontal tab-keyed connector.

To unlock, rotate handle (clockwise), releasing
tension of horizontal tab-keyed connector
cinching mechanism.

Horizontal Panel Assembly

ADJ Products, LLC • Los Angeles, Ca USA • Kerkrade, The Netherlands

17

INSTALLATION - ASSEMBLY

Align the vertical positional posts with their
corresponding alignment holes.

Press the spring-loaded locking latch toward the
left while pressing vertical connector up into
locking-latch.

Release latch to hold the vertical connector. To lock, twist vertical connector lever to the left.

Vertical Panel Assembly

ADJ Products, LLC • Los Angeles, Ca USA • Kerkrade, The Netherlands

18

INSTALLATION – RIGGING BAR

Note the integrated Vertical Connectors
and Vertical Tab-Keyed Sockets.

The VS LED Video Panel is compatible with ADJ’s VSRB1 Rigging Bar (sold separately), which easily
and securely locks to the top of the first panel in a vertical hang of up to 20 VS LED Video Panels,
allowing them hang from a truss, hoist, or lintel beam. A qualified technician or trained professional
is required to fly the VSRB1 Rigging Bar/VS LED Video Panel assembly.

ADJ Products, LLC • Los Angeles, Ca USA • Kerkrade, The Netherlands

19

INSTALLATION – RIGGING BAR, VERTICAL HANG & STACK

VERTICAL HANG

VERTICAL STACK

ADJ Products, LLC • Los Angeles, Ca USA • Kerkrade, The Netherlands

20

INSTALLATION – RIGGING BAR & VERTICAL HANG

Align the vertical positional posts with their
corresponding alignment holes and insert them.

Press spring-loaded locking latch to the left while
pressing vertical connector up into locking-latch.

Release latch to hold the vertical connector. To lock, twist vertical connector lever to the left.

To unlock the vertical connector, rotate lever to the right (counter-clockwise), then press spring­loaded locking latch inward. The vertical connector will drop open.

ADJ Products, LLC • Los Angeles, Ca USA • Kerkrade, The Netherlands

21

INSTALLATION – RIGGING BAR & VERTICAL HANG

THE MAGNETS ARE NOT STRONG ENOUGH TO HOLD A PANEL WITHOUT ASSISTENCE.
HOLD ONE LIFTING HANDLE AT ALL TIMES (WHILE MAINTAINING UPWARD PRESSURE),
UNTIL PANEL IS LOCKED IN PLACE, STARTING WITH OPOSITE VERTICAL LOCK.

Vertical Panel Assembly with integrated magnets for solo technician

The VS LED Video Panels have built-in magnets to assist in vertical hanging for a solo installation.

ADJ Products, LLC • Los Angeles, Ca USA • Kerkrade, The Netherlands

22

ADJ Products, LLC • Los Angeles, Ca USA • Kerkrade, The Netherlands

23

INSTALLATION – RIGGING BAR, VERTICAL STACK

Align the vertical positional posts with their
corresponding alignment holes and insert them.

Press spring-loaded locking latch to the left while
pressing vertical connector up into locking-latch.

Release latch to hold the vertical connector. To lock, twist vertical connector lever to the left.

To unlock the vertical connector, rotate lever to the right (counter-clockwise), then press spring­loaded locking latch inward. The vertical connector will spring-drop open.

USE CAUTION WHEN INSTALLING THE VIDEO PANELS USING THE RIGGING BAR FOR
STACKED ASSEMBLIES. IT IS NOT DESIGNED AS A FREESTANDING ASSEMLBY AND IS
INHERENTLY UNSTABLE. STACKED LED VIDEO PANEL ASSEMBLIES MUST BE
SECURELY INSTALLED BY QUALIFIED TECHNICIANS ONLY!

ADJ Products, LLC • Los Angeles, Ca USA • Kerkrade, The Netherlands

24

INSTALLATION – FLAT PANEL ASSEMBLY

Rear Support Bracket: Use an VS1RSB Rear Support Bracket (sold separately) when connecting
multiple panels for a larger display design, to strengthen the structural integrity of the screen,
improve consistent flatness, and improve overall screen continuity.

ADJ Products, LLC • Los Angeles, Ca USA • Kerkrade, The Netherlands

25

INSTALLATION – HORIZONTAL TRUSS MOUNT (OPTIONAL)

The optional VSR210 Horizontal Truss Mounting Bracket (sold separately) allows for the horizontal
(ceiling) installation of the VS LED Video Panels.

ADJ Products, LLC • Los Angeles, Ca USA • Kerkrade, The Netherlands

26

INSTALLATION – GROUND STACK (OPTIONAL)

The Back Plate can be
loaded with sandbags
to stabilize the stacked
VS Series LED Video
Panel structure

Use (2x) integrated Vertical Connectors
to secure VS Series LED Video Panel to
VSRB1 Single Panel Rigging Bar

The optional VSRB1 Single Panel Rigging / Ground Stack Bar is a free-standing stack mounting

option for the Vision (VS) Series LED Video Panels.

ADJ Products, LLC • Los Angeles, Ca USA • Kerkrade, The Netherlands

27

TECHNICAL SPECIFICATIONS

Part Number

VS2

VS3

VS4

VS5

Resolution

168(H)x168(V)

128(H)x128(V)

104(H)x104(V)

84(H)x84(V)

Pixel Pitch

2.97mm(0.12”)

3.91mm(0.15”)

4.81mm(0.19”)

5.95mm(0.23”)

LED Configuration

SMD212

Pixel Density

112896 pixels/m²

65536 pixels/m²

43264 pixels/m²

28224 pixels/m²

Size

19.68” x 19.68” x 2.74” (500 x 500 x 69.6mm)

Module Quantity

4

Weight

7.7Kg

Mechanical Ratings

Surface Flatness

Gap≤0.5mm

Optical Ratings

Brightness

1000 cd/m²

View Angle

160°/140°

View Distance

3m

4m

3m

6m

Gray Scale

≥14bits

Display COLOR

256

Contrast Ratio

5000:1

Brightness Adjustment

0～100% 100 levels

Power Supply

Operation Power

100～240V 50-60Hz

Max. Power Consumption

600 w/m²

Average Power Consumption

240 w/m²

Max. Panel Power Consumption

170w/per panel

Ave. Panel Power Consumption

68w/per panel

Control Systems

Control Mode

Constant Current Driving

Frame Update Frequency

50-75Hz

Scan Mode

1/21 duty

1/16 duty

1/13 duty

1/7 duty

Refresh Rate

3840Hz

Support Input

Composite, S-Video, Component, VGA, DVI, HDMI, HD_SDI

Control Distance

Ethernet cable≤120m or Fiber Optic＞120m

Support VGA Mode

1024×768, 1280×1024, 1600×1200, 1920×1280

Brightness Correction

Supports

Environmental

Operating Temperature

-20°～+40°

Operating Humidity

10～90% RH No condensation

Operating Life

50000hours

MTBF

5000hours

Protection Level

IP20

Out of Control Rate

≤0.02%

Curve Angle

n/a

Specifications subject to change without any prior written notice.

ADJ Products, LLC • Los Angeles, Ca USA • Kerkrade, The Netherlands

28

ADJ Products, LLC • Los Angeles, Ca USA • Kerkrade, The Netherlands