VIZI BEAM 5RX
©2015 ADJ Products, LLC all rights reserved. Information,
specications, diagrams, images, and instructions herein are
subject to change without notice. ADJ Products, LLC logo and
identifying product names and numbers herein are trademarks
of ADJ Products, LLC. Copyright protection claimed includes all
forms and matters of copyrightable materials and information
now allowed by statutory or judicial law or hereinafter granted.
Product names used in this document may be trademarks or
registered trademarks of their respective companies and are
hereby acknowledged. All non-ADJ Products, LLC brands and
product names are trademarks or registered trademarks of their
respective companies.
ADJ Products, LLC and all aliated companies hereby disclaim any and all liabilities for property, equipment, building,
and electrical damages, injuries to any persons, and direct or
indirect economic loss associated with the use or reliance of
any information contained within this document, and/or as a
result of the improper, unsafe, unsucient and negligent assembly, installation, rigging, and operation of this product.
4/15
User Instructions
Europe Energy Saving Notice
Energy Saving Matters (EuP 2009/125/EC)
Saving electric energy is a key to help protecting the enviroment.
Please turn o all electrical products when they are not in use. To
avoid power consumption in idle mode, disconnect all electrical
equipment from power when not in use. Thank you!
Vizi Beam 5RX
Table of Contents
Unpacking......................................................................3
Introduction....................................................................3
Customer Support......................................................................3
Safety Precautions......................................................................4
Features.........................................................................5
Handling Precautions..................................................................6
Registration......................................................................6
Important Discharge Lamp Warnings.........................................7
Mounting.........................................................................8-9
DMX Set-Up.........................................................................10-12
System Menu.......................................................................13-17
DMX Control..............................................................................17
Oset Menu.........................................................................18-20
DMX Traits............................................................................21-34
Fuse Replacement....................................................................35
Lamp Replacement..............................................................35-37
Photometric Chart.....................................................................35
Cleaning..................................................................39
Trouble Shooting.......................................................................39
Warranty.........................................................................40
Specifications....................................................................42
Vizi Beam 5RX General Information
Unpacking: Thank you for purchasing the Vizi Beam 5RX by ADJ
Products, LLC®. Every Vizi Beam 5RX has been thoroughly tested and
has been shipped in perfect operating condition. Carefully check the
shipping carton for damage that may have occurred during shipping.
If the carton appears to be damaged, carefully inspect your xture for
any damage and be sure all equipment necessary to operate the unit
has arrived intact. In the event damage has been found or parts are
missing, please contact our toll free customer support number for further instructions. Please do not return this unit to your dealer without
contacting customer support rst.
Introduction: The Vizi Beam 5RX is a DMX intelligent, moving head
fixture. The Vizi Beam 5RX can be a 16 channel or 19 channel DMX
unit. The fixture is a DMX controlled unit. The Vizi Beam 5RX is a stand
alone unit. For best results use fog or special effects smoke to enhance
the beams projections.
During the initial start-up or use of this product a light smoke or
smell may arise from the unit. This is a normal process and is
cause by the heat associated with the lamp.
Customer Support: ADJ Products, LLC® provides a toll free cus-
tomer support line, to provide help and to answer any question should
you encounter problems during your set up or initial operation. You
may also visit us on the web at www.adj.com for any comments or
suggestions. Service Hours are Monday through Friday 8:00 a.m. to
4:30 p.m. Pacic Standard Time.
Voice: (800) 322-6337
Fax: (323) 582-2610
E-mail: support@americandj.com
To purchase parts online visit http://parts.americandj.com
Warning! To prevent or reduce the risk of electrical shock or re, do
not expose this unit to rain or moisture.
Warning! This may cause severe eye damage. Avoid looking directly
into the light source at all times!
Please see page 7 for important lamp instructions!
ADJ Products, LLC - www.adj.com - Vizi Beam 5RX Instruction Manual Page 2 ADJ Products, LLC - www.adj.com - Vizi Beam 5RX Instruction Manual Page 3
Vizi Beam 5RX Safety Precautions
Vizi Beam 5RX Features
For Your Own Personal Safety, Please Read and Understand This
Manual Completely Before You Attempt To Install Or Operate
This Unit!
• To reduce the risk of electrical shock or re, do not expose this unit
rain or moisture
• Do not spill water or other liquids into or on to your unit.
• Be sure that the local power outlet match that of the required volt age for your unit.
• Do not attempt to operate this unit if the power cord has been
frayed or broken.
• Do not attempt to remove or break o the ground prong from
the electrical cord. This prong is used to reduce the risk of electrical
shock and re in case of an internal short.
• Disconnect from main power before making any type of connection.
• Do not remove the cover under any conditions. There are no user
serviceable parts inside.
• Never operate this unit when it’s cover is removed.
• Always be sure to mount this unit in an area that will allow proper
ventilation. Allow about 6” (15cm) between this device and a wall.
• Do not attempt to operate this unit, if it becomes damaged.
• This unit is intended for indoor use only, use of this product out doors voids all warranties.
• Always mount this unit in safe and stable matter.
• Power-supply cords should be routed so that they are not likely to
be walked on or pinched by items placed upon or against them,
paying particular attention to cords at plugs, convenience recep tacles, and the point where they exit from the appliance.
• Cleaning -The fixture should be cleaned only as recommended by
the manufacturer. See page 39 for cleaning details.
• Heat -This fixture should be situated away from heat sources such
as radiators, heat registers, stoves, or other appliances (including
amplifiers) that produce heat.
• The fixture should be serviced by qualified service personnel when:
A. Objects have fallen, or liquid has been spilled into the appliance.
B. The appliance has been exposed to rain or water.
C. The appliance does not appear to operate normally or exhibits a
marked change in performance.
• Philips® Platinum 5R Discharge
• Micro-Stepping Motors for Smooth Color and Gobo Transitions
• 2 Modes of DMX-512 Protocol Compatible (16 DMX Channel
Mode or 19 DMX Channel Mode)
• Independent Gobo and Color Wheels
• 17 Static Fixed Gobos + Spot
• 14 Colors, Plus White and Split Colors
• 8 Facet Prism
• Frost Filter
• Strobe Effect
• Built-In Pan/Tilt Macros
• Motorized Focus
• 540˚ Pan Movement
• 270˚ Tilt Movement
• Pan/Tilt Invert
• Digital Display for Address and Function Setting
• Power Cord Daisy Chain (See below)
Vizi Beam 5RX Power Cord Daisy Chain
With this feature you can connect the xtures to one another
using the PowerCon input and output sockets. The quantity
that can be connected is 3 xtures maximum for 120V and 6 xtures maximum for 240V. After the maximum xtures has been
reached you will need to use a new power outlet. They must be
the same xtures. DO NOT mix xtures.
ADJ Products, LLC - www.adj.com - Vizi Beam 5RX Instruction Manual Page 4 ADJ Products, LLC - www.adj.com - Vizi Beam 5RX Instruction Manual Page 5
Vizi Beam 5RX General Instructions
Vizi Beam 5RX Important Discharge Lamp Warning
To optimize the performance of this product, please read these operating
instructions carefully to familiarize yourself with the basic operations of
this unit. These instructions contain important safety information regarding the use and maintenance of this unit. Please keep this manual with
the unit, for future reference.
Vizi Beam 5RX Handling Precautions
Caution! There are no user serviceable parts inside this unit. Do not
attempt any repairs yourself, doing so will void your manufactures
warranty. In the unlikely event your unit may require service please
contact ADJ®.
During operation the housing may become extremely hot. Avoid touching the unit with bare hands while in use.
ADJ® will not accept any liability for any resulting damages caused by
the non-observance of this manual or any unauthorized modication
to this unit.
Vizi Beam 5RX Product
The Vizi Beam 5RX carries a one year limited warranty. Please fill out
the enclosed warranty card to validate your purchase. All returned
service items whether under warranty or not, must be freight prepaid and accompany a return authorization (R.A.) number. The R.A.
number must be clearly written on the outside of the return package.
A brief description of the problem as well as the R.A. number must
also be written down on a piece of paper and included in the shipping
carton. If the unit is under warranty, you must provide a copy of your
proof of purchase invoice. You may obtain a R.A. number by contacting our customer support team on our toll free customer support
number. All packages returned to the service department not displaying a R.A. number on the outside of the package will be returned to
the shipper at the shippers cost.
Registration
This fixture is fitted with a discharge lamp which is
highly susceptible to damage if improperly handled.
Never touch the lamp with your bare fingers as the
oil from your hands will shorten lamp life. Also, never
move the fixture until the lamps have had ample time
to cool. Remember, lamps are not covered under war-
ranty conditions.
This unit emits intense UV radiation which is harmful to the eyes and skin.
The intense luminance of the lamp can cause severe damage to the retina.
Never operate this unit without it’s covers, these covers have been specially
designed to shield against UV radiation.
Epileptic Warning: Those suering from epilepsy should avoid looking directly
into the lamp at all times.
Avoid switching the xture on and o repeatedly in short intervals as this will
reduce lamp life and intensity.
To achieve the intensity associated with discharge lamps, these lamps use
gas sealed in a high pressure environment to emit a brilliant output. Due to
the high pressure involved with the construction of the lamp, the lamp may
explode during prolonged extensive use. This risk is increased with age,
added care is encouraged when dealing with older lamps. Extreme caution
should be used when operating this or any xture tted with a gas discharge
lamp. Never open this unit while in use.
VERY IMPORTANT: This is for your safety and the life length of the unit.
The Philips® Platinum 5R Discharge lamp has lifetime of 3000 hours.
ADJ recommends periodically checking the lamp running time. When the
lamp reaches the 3000 hour mark, or close to it, we strongly suggest you
switch the lamp out.
Replace the lamp following the instructions on pages 35-38. After replaceing
the lamp you must clear the LAMP RUNNING TIME (see page 15 “FHRS”).
Warning: DO NOT use this lamp more then 3000 hours. Using the lamp
any longer then the set life could seriously damage your unit.
ADJ Products, LLC - www.adj.com - Vizi Beam 5RX Instruction Manual Page 6
ADJ Products, LLC - www.adj.com - Vizi Beam 5RX Instruction Manual Page 7
Vizi Beam 5RX Mounting
Vizi Beam 5RX Mounting
When installing the unit, the trussing or area of installation must be
able to hold 10 times the weight without any deformation. When
installing the unit must be secured with a secondary safety attachment, e.g. and appropriate safety cable. Never stand directly below
the unit when mounting, removing, or servicing the unit.
Overhead mounting requires extensive experience, including calculating working load limits, installation material being used, and perodic
safety inspection of all installation material and unit. If you lack these
qualications, do not attempt the installation yourself.
These installaiton should be checked by a skilled person once a year.
NOTICE: The suitable enviromental temperature for this lighting xture is between -25˚ C to 45˚ C. Do not place this lighting
xture in an enviroment where the temperatures are under or
above the temperatures stated above. This will allow the xture
to run at its best and help prolong the xture life.
The Vizi Beam 5RX is fully operational in two dierent mounting positions, hanging upside-down from a ceiling or set on a at level sur-
face. To avoid internal damage to the unit, never mount the unit
on its side as illustrated above. Be sure this xture is kept at least
0.5m away from any ammable materials (decoration etc.). Always
use and install the supplied safety cable as a safety measure to
prevent accidental damage and/or injury in the event the clamp fails
(see next page). Never use the carrying handles for secondary attach-
ment.
ADJ Products, LLC - www.adj.com - Vizi Beam 5RX Instruction Manual Page 8
Screw one clamp each via a M12 screw and nut onto the
Omega holders. Insert the quick-lock fasteners of the rst
Omega holder into the respective holes on the bottom of the
Vizi Beam 5RX. Tighten the quick-lock fasteners fully clockwise.
Install the second Omega holder. Pull the safety-cable through
the openings located on the base plate and over the trussing
system or a safe xation spot. Insert the end in the carabine
and tighten the safety screw.
ADJ Products, LLC - www.adj.com - Vizi Beam 5RX Instruction Manual Page 9
Vizi Beam 5RX Set Up
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
DMX512
DMX+,DMX-,COMMON
1
2
3
Termination reduces signal errors and
avoids signal transmission problems
and interference. It is always advisable
to connect a DMX terminal, (Resistance
120 Ohm 1/4 W) between PIN 2 (DMX-)
and PIN 3 (DMX +) of the last fixture.
POWER
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
and PIN 3 (DMX +) of the last fixture.
Vizi Beam 5RX Set Up
Power Supply: The ADJ® Vizi Beam 5RX contains a electronic bal-
last, which will auto sense the voltage when it is plugged into the power
source. With the electronic ballast you do not need to worry about wall
voltage, this unit can be plugged in anywhere.
DMX-512: DMX is short for Digital Multiplex. This is a universal pro-
tocol used by most lighting and controller manufactures as a form of
communication between intelligent fixtures and controllers. A DMX
controller sends DMX data instructions from the controller to the fixture. DMX data is sent as serial data that travels from fixture to fixture
via the DATA “IN” and DATA “OUT” XLR terminals located on all DMX
fixtures (most controllers only have a DATA “OUT” terminal).
DMX Linking: DMX is a language allowing all makes and models
of dierent manufactures to be linked together and operate from a
single controller, as long as all xtures and the controller are DMX
compliant. To ensure proper DMX data transmission, when using
several DMX fixtures try to use the shortest cable path possible. The
order in which fixtures are connected in a DMX line does not influence
the DMX addressing. For example; a fixture assigned a DMX address
of 1 may be placed anywhere in a DMX line, at the beginning, at the
end, or anywhere in the middle. Therefore, the first fixture controlled
by the controller could be the last fixture in the chain. When a fixture
is assigned a DMX address of 1, the DMX controller knows to send
DATA assigned to address 1 to that unit, no matter where it is located
in the DMX chain.
Data Cable (DMX Cable) Requirements (For DMX and Master/Slave
Operation): The Vizi Beam 5RX can be controlled via DMX-512 pro-
tocol. The Vizi Beam 5RX can be either a 16 or 19 channel DMX unit.
The DMX address is set electronically using the controls on the side
panel of the unit. Your unit and your DMX controller require a approved DMX-512 110 Ohm Data
cable for data input and data output (Figure 1). We
recommend Accu-Cable DMX cables. If you are
making your own cables, be sure to use standard
110-120 Ohm shielded cable (This cable may be
purchased at almost all professional sound and
lighting stores). Your cables should be made with
a male and female XLR connector on either end of the cable. Also
ADJ Products, LLC - www.adj.com - Vizi Beam 5RX Instruction Manual Page 10 ADJ Products, LLC - www.adj.com - Vizi Beam 5RX Instruction Manual Page 11
Figure 1
remember that DMX cable must be daisy chained and cannot be split.
Notice: Be sure to follow gures two and three when making your own
cables. Do not use the ground lug on the XLR connector. Do not connect the cable’s shield conductor to the ground lug or allow the shield
conductor to come in contact with the XLR’s outer casing. Grounding
the shield could cause a short circuit and erratic behavior.
COMMON
1
DMX512 IN
3
3-PIN XLR
2
Figure 2
XLR Pin Conguration
Pin 1 = Ground
Pin 2 = Data Compliment (negative)
Pin 3 = Data True (positive)
When longer runs of cable are
Figure 4
XLR Male Socket
1 Ground
DMX512 OUT
3-PIN XLR
2 Cold
3 Hot
1
2
3
2 Cold
DMX +
DMX -
XLR Female Socket
1 Ground
3 Hot
Figure 3
Special Note: Line Termination.
used, you may need to use a terminator on the last unit to avoid erratic
behavior. A terminator is a 110-120 ohm 1/4 watt resistor which is connected between pins 2 and 3 of a male XLR connector (DATA + and
DATA -). This unit is inserted in the female XLR connector of the last
unit in your daisy chain to terminate the line. Using a cable terminator
(ADJ part number Z-DMX/T) will decrease the possibilities of erratic
behavior.
Termination reduces signal errors and
1
avoids signal transmission problems
3
and interference. It is always advisable
2
to connect a DMX terminal, (Resistance
120 Ohm 1/4 W) between PIN 2 (DMX-)
Vizi Beam 5RX Set Up Vizi Beam 5RX System Menu
5-Pin XLR DMX Connectors.
Some manufactures use 5-pin DMX-
512 data cables for DATA transmission in place of 3-pin. 5-pin DMX
xtures may be implemented in a 3-pin DMX line. When inserting standard 5-pin data cables in to a 3-pin line a cable adaptor must be used,
these adaptors are readily available at most electric stores. The chart
below details a proper cable conversion.
3-Pin XLR to 5-Pin XLR Conversion
Conductor 5-Pin XLR Male (In)3-Pin XLR Female (Out)
Ground/Shield
Data Compliment (- signal)
Data True (+ signal)
Not Used
Not Used
Pin 1
Pin 2
Pin 3
Pin 1
Pin 2
Pin 3
Pin 4 - Do Not Use
Pin 5 - Do Not Use
ADJ Products, LLC - www.adj.com - Vizi Beam 5RX Instruction Manual Page 12
ADJ Products, LLC - www.adj.com - Vizi Beam 5RX Instruction Manual Page 13
Vizi Beam 5RX System Menu Vizi Beam 5RX System Menu
System Menu: When making adjustments press ENTER to
conrm your setup then press and hold the MENU button
for at least 3 seconds. To exit without making any adjustments press the MENU button. The display will lock after 30
seconds, press the MENU button for 3 seconds to unlock.
ADDR - DMX Address Setting.
1. Press the either the MENU, UP, or DOWN buttons until
“ADDR” is displayed, press ENTER.
2. The current address will now be displayed and ashing.
Press the UP or DOWN buttons to nd your desired address.
Press ENTER to set your desired DMX address.
CHND - This will let select your desired DMX channel
mode.
1. Press the either the MENU button until “CHND” is displayed,
press ENTER. Either “16CH” or “19CH” will be displayed
2. Press the UP or DOWN buttons to nd your desired DMX
channel mode and press ENTER to conm and exit.
until “Yes” is displayed, press ENTER to conm. To deactivate
tilt inversion, select “No” and press Enter.
LED - With this function you can have the display back-
light turn off after 10 seconds.
1. Press the MENU button until “LED” is displayed, press
ENTER.
2. The display will show either “ON” or “OFF”. Press the UP or
DOWN buttons to select “ON” to keep the LED display on at
all times, or “OFF” to switch to have the LED display switch o
after 10 seconds.
3. Press ENTER to conrm. To make you LED display reappear
again press any button.
DISP - This function will reverse the display 180º.
1. Press the MENU button until “DISP” is displayed, press
ENTER.
2. Press ENTER to “ip” the display. Press ENTER to “ip” it
again. Press ENTER when you have made your desired setup.
IPAN - Pan Inversion
1. Press the MENU button until “IPAN” is displayed, press
ENTER. Either “Yes” or “No” will be displayed.
2. To activate the Pan inversion press the UP or DOWN buttons
until “Yes” is displayed, press ENTER to conm. To deactivate
Pan inversion, select “No” and press Enter.
ITLT - Tilt Inversion
1. Press the MENU button until “ITLT” is displayed, press
ENTER. Either “Yes” or “No” will be displayed.
2. To activate the tilt inversion press the UP or DOWN buttons
TEST - This function will run a self test program.
1. Press the MENU button until “TEST” is displayed, press
ENTER.
2. The xture will now run a self test.
FHRS - This serves two functions; displays the lamp
running time and clears the lamp running time. The lamp
running time needs to be cleared after a new lamp has been
installed.
1. Press the MENU button until “FHRS” is displayed, press
ENTER.
ADJ Products, LLC - www.adj.com - Vizi Beam 5RX Instruction Manual Page 15ADJ Products, LLC - www.adj.com - Vizi Beam 5RX Instruction Manual Page 14
Vizi Beam 5RX System Menu
Vizi Beam 5RX System Menu
2. The lamp running time will now be displayed. Press MENU to
exit.
3. To clear the lamp running time, when lamp running time is
displayed press the ENTER button. Either “NO” or “CLea” will
be displayed.
4. Use the UP or DOWN buttons to select “CLea” and press
ENTER. The lamp running time will now be cleared. You should
clear the lamp running time everytime you change the
lamp.
LAMP - With this function you can turn the lamp on/off
while the unit is still powered on.
1. Press the MENU button until “LAMP” is displayed, press
ENTER.
2. The display will show either “ON” or “OFF”. Press the UP or
DOWN buttons to select “ON” to keep the lamp on at all times,
or “OFF” to turn the lamp o while the unit is still powered on.
3. Press ENTER to conrm.
LPND - With this function you can turn the lamp on or
off while the power is on.
1. Press the MENU button until “LPND” is displayed, press
ENTER.
2. The display will show either “ON” or “OFF”. Press the UP or
DOWN buttons to select “ON” to keep the lamp on at all times,
or “OFF” to turn the lamp o while the unit is still powered on.
3. Press ENTER to conrm.
VER - Use this function to display the Software version of
the unit.
press ENTER.
2. The display will show the software version.
DEF - Use this function to revert back to the default set-
tings.
1. Press the either the MENU button until “deF” is displayed,
press ENTER.
2. The display will show the software version.
RSET - Use this function to reset the unit.
1. Press the MENU button until “RSET” is displayed, press
ENTER.
2. The xture will now reset.
Vizi Beam 5RX DMX Control
Universal DMX Control: This function allows you to use a univer-
sal DMX-512 controller. A DMX controller allows you to create unique
programs tailored to your individual needs.
1. The Vizi Beam 5RX has 2 DMX channel modes, 16 channel mode
and 19 channel mode. See pages 21-34 for detailed description
of the DMX traits.
2. To control your fixture in DMX mode, follow the set-up procedures
on pages 10-12 as well as the set-up specifications that are
included with your DMX controller.
3. Follow the instructions on page 14 to select your desired DMX
channel mode and to set the DMX address.
4. Use the controller’s faders to control the various DMX fixture traits.
5. For longer cable runs (more than a 100 feet) use a terminator on
the last fixture.
6. For help operating in DMX mode consult the manual included
with your DMX controller.
1. Press the either the MENU button until “VER” is displayed,
ADJ Products, LLC - www.adj.com - Vizi Beam 5RX Instruction Manual Page 17ADJ Products, LLC - www.adj.com - Vizi Beam 5RX Instruction Manual Page 16
Vizi Beam 5RX Offset Menu Vizi Beam 5RX Offset Menu
2. Use the UP and DOWN buttons to make your adjustments, and
then press ENTER to conrm. Press the MENU button for one second
to exit.
ODNN - Setting adjustment for the color wheel.
1. Press the ENTER button for at least 3 seconds, then press the UP
or DOWN buttons so that “odnn” is displayed, press ENTER.
2. Use the UP and DOWN buttons to make your adjustments, and
then press ENTER to conrm. Press the MENU button for one second
to exit.
OCOL - Setting adjustment for the color wheel.
1. Press the ENTER button for at least 3 seconds, then press the UP
or DOWN buttons so that “oCoL” is displayed, press ENTER.
2. Use the UP and DOWN buttons to make your adjustments, and
then press ENTER to conrm. Press the MENU button for one second
to exit.
To enter the Oset Menu, press the ENTER button for at least 3 seconds. In this submenu you are able to adjust the home position of the
pan, tilt, color wheel, gobo wheel, RGobo (Rotating) wheel, prism, R
(Rotating)Prism, and focus position.
OPAN - Adjustment of the pan home position.
1. Press the ENTER button for at least 3 seconds, then press the UP
or DOWN buttons so that “oPAn” is displayed, press ENTER.
2. Use the UP and DOWN buttons to make your adjustments, and
then press ENTER to conrm. Press the MENU button for one second
to exit.
OTLL - Adjustment of the tilt home position.
1. Press the ENTER button for at least 3 seconds, then press the UP
or DOWN buttons so that “otLL” is displayed, press ENTER.
OGOB - Setting adjustment for the gobo wheel.
1. Press the ENTER button for at least 3 seconds, then press the UP
or DOWN buttons so that “oGob” is displayed, press ENTER.
2. Use the UP and DOWN buttons to make your adjustments, and
then press ENTER to conrm. Press the MENU button for one second
to exit.
OPRI - Setting adjustment for the prism.
1. Press the ENTER button for at least 3 seconds, then press the UP
or DOWN buttons so that “oPrI” is displayed, press ENTER.
2. Use the UP and DOWN buttons to make your adjustments, and
then press ENTER to conrm. Press the MENU button for one second
to exit.
ADJ Products, LLC - www.adj.com - Vizi Beam 5RX Instruction Manual Page 19ADJ Products, LLC - www.adj.com - Vizi Beam 5RX Instruction Manual Page 18
Vizi Beam 5RX Offset Menu
Vizi Beam 5RX 16 Channel DMX Mode
ORPR - Setting adjustment for the rotating prism.
1. Press the ENTER button for at least 3 seconds, then press the UP
or DOWN buttons so that “orPr” is displayed, press ENTER.
2. Use the UP and DOWN buttons to make your adjustments, and
then press ENTER to conrm. Press the MENU button for one second
to exit.
OFRO - Setting adjustment for the frost lter.
1. Press the ENTER button for at least 3 seconds, then press the UP
or DOWN buttons so that “oFro” is displayed, press ENTER.
2. Use the UP and DOWN buttons to make your adjustments, and
then press ENTER to conrm. Press the MENU button for one second
to exit.
OFOC - Setting adjustment for the focus.
1. Press the ENTER button for at least 3 seconds, then press the UP
or DOWN buttons so that “oFoC” is displayed, press ENTER.
2. Use the UP and DOWN buttons to make your adjustments, and
then press ENTER to conrm. Press the MENU button for one second
to exit.
Channel Value Function
1 0 - 255 PAN MOVEMENT
2 0 - 255 PAN FINE
3 0 - 255 TILT MOVEMENT
4 0 - 255 TILT FINE
5 COLOR WHEEL
0 - 2 WHITE
3 - 4 WHITE & COLOR 1
5 - 6 COLOR 1
7 - 8 COLOR 1 & COLOR 2
9 - 10 COLOR 2
11 - 12 COLOR 2 & COLOR 3
13 - 14 COLOR 3
15 - 16 COLOR 3 & COLOR 4
17 - 18 COLOR 4
19 - 21 COLOR 4 & COLOR 5
22 - 23 COLOR 5
24 - 25 COLOR 5 & COLOR 6
26 - 27 COLOR 6
28 - 29 COLOR 6 & COLOR 7
30 - 31 COLOR 7
32 - 33 COLOR 7 & COLOR 8
34 - 35 COLOR 8
36 - 37 COLOR 8 & COLOR 9
38 - 39 COLOR 9
40 - 42 COLOR 9 & COLOR 10
43 - 44 COLOR 10
45 - 46 COLOR 10 & COLOR 11
47 - 48 COLOR 11
49 - 50 COLOR 11 & COLOR 12
51 - 52 COLOR 12
53 - 54 COLOR 12 & COLOR 13
55 - 56 COLOR 13
57 - 58 COLOR 13 & COLOR 14
ADJ Products, LLC - www.adj.com - Vizi Beam 5RX Instruction Manual Page 21ADJ Products, LLC - www.adj.com - Vizi Beam 5RX Instruction Manual Page 20
Vizi Beam 5RX 16 Channel DMX Mode
Vizi Beam 5RX 16 Channel DMX Mode
Channel Value Function
5 COLOR WHEEL
59 - 60 COLOR 14
61 - 63 COLOR 14 & WHITE
64 - 127 COLOR INDEXING
128 - 189 CLOCKWISE ROTATION
FAST - SLOW
190 - 193 NO ROTATION
194 - 255 COUNTER-CLOCKWISE ROTATION
SLOW - FAST
6 GOBOS
0 - 3 OPEN
4 - 6 GOBO 1
7 - 9 GOBO 2
10 - 12 GOBO 3
13 - 15 GOBO 4
16 - 18 GOBO 5
19 - 21 GOBO 6
22 - 24 GOBO 7
25 - 27 GOBO 8
28 - 30 GOBO 9
31 - 33 GOBO 10
34 - 36 GOBO 11
37 - 39 GOBO 12
40 - 42 GOBO 13
43 - 45 GOBO 14
46 - 48 GOBO 15
49 - 51 GOBO 16
52 - 55 GOBO 17
56 - 59 OPEN SHAKING
60 - 63 GOBO 1 SHAKING
64 - 68 GOBO 2 SHAKING
69 - 71 GOBO 3 SHAKING
72 - 75 GOBO 4 SHAKING
76 - 79 GOBO 5 SHAKING
Channel Value Function
6 GOBOS
80 - 83 GOBO 6 SHAKING
84 - 87 GOBO 7 SHAKING
88 - 91 GOBO 8 SHAKING
92 - 95 GOBO 9 SHAKING
96 - 99 GOBO 10 SHAKING
100 - 103 GOBO 11 SHAKING
104 - 107 GOBO 12 SHAKING
108 - 111 GOBO 13 SHAKING
112 - 115 GOBO 14 SHAKING
116 - 119 GOBO 15 SHAKING
120 - 123 GOBO 16 SHAKING
124 - 127 GOBO 17 SHAKING
128 - 189 GOBO WHEEL ROTATION
FAST - SLOW
190 - 193 STOP
194 - 255 GOBO WHEEL ROTATION
SLOW - FAST
7 PRISM
0 - 7 OPEN
8 - 1 2 7 P R I S M
128 - 132 PRISM ROTATION EFFECT 1
133 - 137 PRISM ROTATION EFFECT 2
138 - 141 PRISM ROTATION EFFECT 3
142 - 146 PRISM ROTATION EFFECT 4
147 - 150 PRISM ROTATION EFFECT 5
151 - 155 PRISM ROTATION EFFECT 6
156 - 159 PRISM ROTATION EFFECT 7
160 - 164 PRISM ROTATION EFFECT 8
165 - 168 PRISM ROTATION EFFECT 9
169 - 173 PRISM ROTATION EFFECT 10
174 - 177 PRISM ROTATION EFFECT 11
178 - 182 PRISM ROTATION EFFECT 12
183 - 187 PRISM ROTATION EFFECT 13
ADJ Products, LLC - www.adj.com - Vizi Beam 5RX Instruction Manual Page 23ADJ Products, LLC - www.adj.com - Vizi Beam 5RX Instruction Manual Page 22
Vizi Beam 5RX 16 Channel DMX Mode
Vizi Beam 5RX 16 Channel DMX Mode
Channel Value Function
7 188 - 191 PRISM ROTATION EFFECT 14
192 - 196 PRISM ROTATION EFFECT 15
197 - 200 PRISM ROTATION EFFECT 16
201 - 205 PRISM ROTATION EFFECT 17
206 - 209 PRISM ROTATION EFFECT 18
210 - 214 PRISM ROTATION EFFECT 19
215 - 218 PRISM ROTATION EFFECT 20
219 - 223 PRISM ROTATION EFFECT 21
224 - 227 PRISM ROTATION EFFECT 22
228 - 232 PRISM ROTATION EFFECT 23
233 - 236 PRISM ROTATION EFFECT 24
237 - 241 PRISM ROTATION EFFECT 25
242 - 246 PRISM ROTATION EFFECT 26
247 - 250 PRISM ROTATION EFFECT 27
251 - 255 PRISM ROTATION EFFECT 28
8 PRISM ROTATION
0 - 127 INDEX ROTATION
128 - 190 CLOCKWISE ROTATION
FAST - SLOW
191 - 192 STOP
193 - 255 COUNTER-CLOCKWISE ROTATION
SLOW - FAST
9 FOCUS
0 - 255 0% - 100%
10 FROST
0 - 255 0% - 100%
11 SHUTTER & STROBE
0 - 7 SHUTTER CLOSED
8 - 15 SHUTTER OPEN
16 - 167 LINEAR STROBING SLOW - FAST
168 - 203 FAST CLOSE - SLOW OPEN
204 - 239 FAST OPEN - SLOW CLOSE
240 - 247 RANDOM STROBE
248 - 255 OPEN
Channel Value Function
12 MASTER DIMMER
0 - 255 INTENSITY 0% - 100%
13 PAN/TILT MACROS
0 - 7 OFF
8 - 15 MACRO 1
16 - 23 MACRO 2
24 - 31 MACRO 3
32 - 39 MACRO 4
40 - 47 MACRO 5
48 - 55 MACRO 6
56 - 63 MACRO 7
64 - 71 MACRO 8
72 - 79 MACRO 9
80 - 87 MACRO 10
88 - 95 MACRO 11
96 - 103 MACRO 12
104 - 111 MACRO 13
112 - 119 MACRO 14
120 - 127 MACRO 15
128 - 135 MACRO 16
136 - 143 MACRO 17
144 - 151 MACRO 18
152 - 159 MACRO 19
160 - 167 MACRO 20
168 - 175 MACRO 21
176 - 183 MACRO 22
184 - 191 MACRO 23
192 - 199 MACRO 24
200 - 207 MACRO 25
208 - 215 MACRO 26
216 - 223 MACRO 27
224 - 231 MACRO 28
232 - 239 MACRO 29
240 - 247 MACRO 30
ADJ Products, LLC - www.adj.com - Vizi Beam 5RX Instruction Manual Page 25ADJ Products, LLC - www.adj.com - Vizi Beam 5RX Instruction Manual Page 24
Vizi Beam 5RX 16 Channel DMX Mode
Vizi Beam 5RX 16 Channel DMX Mode
Channel Value Function
13 PAN/TILT MACROS
248 - 255 MACRO 31
14 PAN/TILT MACRO SPEED
0 - 255 FAST - SLOW
15 PAN/TILT MOVEMENT SPEED
0 - 255 FAST - SLOW
16 SPECIAL FUNCTIONS
0 - 49 NO FUNCTION
50 - 59 PAN/TILT FAST MODE
60 - 69 PAN/TILT NORMAL MODE
70 - 79 BLACKOUT WITH PAN/TILT MOVE
ENABLED
80 - 89 BLACKOUT WITH PAN/TILT MOVE
DISABLED
90 - 99 BLACKOUT WITH COLOR CHANGE
ENABLED
100 - 109 BLACKOUT WITH COLOR CHANGE
DISABLED
110 - 119 BLACKOUT WITH GOBO CHANGE
ENABLED
120 - 129 BLACKOUT WITH GOBO CHANGE
DISABLED
130 - 139 LAMP ON
140 - 149 PAN/TILT RESET
150 - 159 COLOR WHEEL RESET
160 - 169 GOBO WHEEL RESET
170 - 179 SHUTTER/PRISM & PRISM ROTA TION/FROST/FOCUSE RESET
180 - 199 NO FUNCTION
200 - 209 RESET ALL
210 - 219 BLACKOUT WITH PAN/TILT/COLOR/
GOBO CHANGE ENABLED
220 - 229 BLACKOUT WITH PAN/TILT/COLOR/
GOBO CHANGE DISABLED
Channel Value Function
16 SPECIAL FUNCTIONS
230 - 239 LAMP OFF
240 - 255 NO FUNCTION
ADJ Products, LLC - www.adj.com - Vizi Beam 5RX Instruction Manual Page 27ADJ Products, LLC - www.adj.com - Vizi Beam 5RX Instruction Manual Page 26
Vizi Beam 5RX 19 Channel DMX Mode
Vizi Beam 5RX 19 Channel DMX Mode
Channel Value Function
1 0 - 255 PAN MOVEMENT
2 0 - 255 PAN FINE
3 0 - 255 TILT MOVEMENT
4 0 - 255 TILT FINE
5 COLOR WHEEL
0 - 2 WHITE
3 - 4 WHITE & COLOR 1
5 - 6 COLOR 1
7 - 8 COLOR 1 & COLOR 2
9 - 10 COLOR 2
11 - 12 COLOR 2 & COLOR 3
13 - 14 COLOR 3
15 - 16 COLOR 3 & COLOR 4
17 - 18 COLOR 4
19 - 21 COLOR 4 & COLOR 5
22 - 23 COLOR 5
24 - 25 COLOR 5 & COLOR 6
26 - 27 COLOR 6
28 - 29 COLOR 6 & COLOR 7
30 - 31 COLOR 7
32 - 33 COLOR 7 & COLOR 8
34 - 35 COLOR 8
36 - 37 COLOR 8 & COLOR 9
38 - 39 COLOR 9
40 - 42 COLOR 9 & COLOR 10
43 - 44 COLOR 10
45 - 46 COLOR 10 & COLOR 11
47 - 48 COLOR 11
49 - 50 COLOR 11 & COLOR 12
51 - 52 COLOR 12
53 - 54 COLOR 12 & COLOR 13
55 - 56 COLOR 13
57 - 58 COLOR 13 & COLOR 14
Channel Value Function
5 COLOR WHEEL
59 - 60 COLOR 14
61 - 63 COLOR 14 & WHITE
64 - 127 COLOR INDEXING
128 - 189 CLOCKWISE ROTATION
FAST - SLOW
190 - 193 NO ROTATION
194 - 255 COUNTER-CLOCKWISE ROTATION
SLOW - FAST
6 GOBOS
0 - 3 OPEN
4 - 6 GOBO 1
7 - 9 GOBO 2
10 - 12 GOBO 3
13 - 15 GOBO 4
16 - 18 GOBO 5
19 - 21 GOBO 6
22 - 24 GOBO 7
25 - 27 GOBO 8
28 - 30 GOBO 9
31 - 33 GOBO 10
34 - 36 GOBO 11
37 - 39 GOBO 12
40 - 42 GOBO 13
43 - 45 GOBO 14
46 - 48 GOBO 15
49 - 51 GOBO 16
52 - 55 GOBO 17
56 - 59 OPEN SHAKING
60 - 63 GOBO 1 SHAKING
64 - 68 GOBO 2 SHAKING
69 - 71 GOBO 3 SHAKING
72 - 75 GOBO 4 SHAKING
76 - 79 GOBO 5 SHAKING
ADJ Products, LLC - www.adj.com - Vizi Beam 5RX Instruction Manual Page 29ADJ Products, LLC - www.adj.com - Vizi Beam 5RX Instruction Manual Page 28
Vizi Beam 5RX 19 Channel DMX Mode
Vizi Beam 5RX 19 Channel DMX Mode
Channel Value Function
6 GOBOS
80 - 83 GOBO 6 SHAKING
84 - 87 GOBO 7 SHAKING
88 - 91 GOBO 8 SHAKING
92 - 95 GOBO 9 SHAKING
96 - 99 GOBO 10 SHAKING
100 - 103 GOBO 11 SHAKING
104 - 107 GOBO 12 SHAKING
108 - 111 GOBO 13 SHAKING
112 - 115 GOBO 14 SHAKING
116 - 119 GOBO 15 SHAKING
120 - 123 GOBO 16 SHAKING
124 - 127 GOBO 17 SHAKING
128 - 189 GOBO WHEEL ROTATION
FAST - SLOW
190 - 193 STOP
194 - 255 GOBO WHEEL ROTATION
SLOW - FAST
7 PRISM
0 - 7 OPEN
8 - 1 2 7 P R I S M
128 - 132 PRISM ROTATION EFFECT 1
133 - 137 PRISM ROTATION EFFECT 2
138 - 141 PRISM ROTATION EFFECT 3
142 - 146 PRISM ROTATION EFFECT 4
147 - 150 PRISM ROTATION EFFECT 5
151 - 155 PRISM ROTATION EFFECT 6
156 - 159 PRISM ROTATION EFFECT 7
160 - 164 PRISM ROTATION EFFECT 8
165 - 168 PRISM ROTATION EFFECT 9
169 - 173 PRISM ROTATION EFFECT 10
174 - 177 PRISM ROTATION EFFECT 11
178 - 182 PRISM ROTATION EFFECT 12
183 - 187 PRISM ROTATION EFFECT 13
ADJ Products, LLC - www.adj.com - Vizi Beam 5RX Instruction Manual Page 30 ADJ Products, LLC - www.adj.com - Vizi Beam 5RX Instruction Manual Page 31
Channel Value Function
7 188 - 191 PRISM ROTATION EFFECT 14
192 - 196 PRISM ROTATION EFFECT 15
197 - 200 PRISM ROTATION EFFECT 16
201 - 205 PRISM ROTATION EFFECT 17
206 - 209 PRISM ROTATION EFFECT 18
210 - 214 PRISM ROTATION EFFECT 19
215 - 218 PRISM ROTATION EFFECT 20
219 - 223 PRISM ROTATION EFFECT 21
224 - 227 PRISM ROTATION EFFECT 22
228 - 232 PRISM ROTATION EFFECT 23
233 - 236 PRISM ROTATION EFFECT 24
237 - 241 PRISM ROTATION EFFECT 25
242 - 246 PRISM ROTATION EFFECT 26
247 - 250 PRISM ROTATION EFFECT 27
251 - 255 PRISM ROTATION EFFECT 28
8 PRISM ROTATION
0 - 127 INDEX ROTATION
128 - 190 CLOCKWISE ROTATION
FAST - SLOW
191 - 192 STOP
193 - 255 COUNTER-CLOCKWISE ROTATION
SLOW - FAST
9 FOCUS
0 - 255 0% - 100%
10 FROST
0 - 255 0% - 100%
11 SHUTTER & STROBE
0 - 7 SHUTTER CLOSED
8 - 15 SHUTTER OPEN
16 - 167 LINEAR STROBING SLOW - FAST
168 - 203 FAST CLOSE - SLOW OPEN
204 - 239 FAST OPEN - SLOW CLOSE
240 - 247 RANDOM STROBE
248 - 255 OPEN
Vizi Beam 5RX 19 Channel DMX Mode
Vizi Beam 5RX 19 Channel DMX Mode
Channel Value Function
12 MASTER DIMMER
0 - 255 INTENSITY 0% - 100%
13 PAN/TILT MACROS
0 - 7 OFF
8 - 15 MACRO 1
16 - 23 MACRO 2
24 - 31 MACRO 3
32 - 39 MACRO 4
40 - 47 MACRO 5
48 - 55 MACRO 6
56 - 63 MACRO 7
64 - 71 MACRO 8
72 - 79 MACRO 9
80 - 87 MACRO 10
88 - 95 MACRO 11
96 - 103 MACRO 12
104 - 111 MACRO 13
112 - 119 MACRO 14
120 - 127 MACRO 15
128 - 135 MACRO 16
136 - 143 MACRO 17
144 - 151 MACRO 18
152 - 159 MACRO 19
160 - 167 MACRO 20
168 - 175 MACRO 21
176 - 183 MACRO 22
184 - 191 MACRO 23
192 - 199 MACRO 24
200 - 207 MACRO 25
208 - 215 MACRO 26
216 - 223 MACRO 27
224 - 231 MACRO 28
232 - 239 MACRO 29
240 - 247 MACRO 30
ADJ Products, LLC - www.adj.com - Vizi Beam 5RX Instruction Manual Page 32 ADJ Products, LLC - www.adj.com - Vizi Beam 5RX Instruction Manual Page 33
Channel Value Function
13 PAN/TILT MACROS
248 - 255 MACRO 31
14 PAN/TILT MACRO SPEED
0 - 255 FAST - SLOW
15 COLOR TIME
0 - 254 FAST - SLOW
255 FAST
16 BEAM TIME
0 - 254 FAST - SLOW
255 FAST
17 GOBO TIME
0 - 254 FAST - SLOW
255 FAST
18 PAN/TILT MOVEMENT SPEED
0 - 255 FAST - SLOW
19 SPECIAL FUNCTIONS
0 - 49 NO FUNCTION
50 - 59 PAN/TILT FAST MODE
60 - 69 PAN/TILT NORMAL MODE
70 - 79 BLACKOUT WITH PAN/TILT MOVE
ENABLED
80 - 89 BLACKOUT WITH PAN/TILT MOVE
DISABLED
90 - 99 BLACKOUT WITH COLOR CHANGE
ENABLED
100 - 109 BLACKOUT WITH COLOR CHANGE
DISABLED
110 - 119 BLACKOUT WITH GOBO CHANGE
ENABLED
120 - 129 BLACKOUT WITH GOBO CHANGE
DISABLED
130 - 139 LAMP ON
140 - 149 PAN/TILT RESET
150 - 159 COLOR WHEEL RESET
Vizi Beam 5RX 19 Channel DMX Mode
Vizi Beam 5RX Lamp & Fuse Replacement
Channel Value Function
19 SPECIAL FUNCTIONS
160 - 169 GOBO WHEEL RESET
170 - 179 SHUTTER/PRISM & PRISM ROTA TION/FROST/FOCUSE RESET
180 - 199 NO FUNCTION
200 - 209 RESET ALL
210 - 219 BLACKOUT WITH PAN/TILT/COLOR/
GOBO CHANGE ENABLED
220 - 229 BLACKOUT WITH PAN/TILT/COLOR/
GOBO CHANGE DISABLED
230 - 239 LAMP OFF
240 - 255 NO FUNCTION
Caution: Always replace with the exact same type lamp and fuse,
unless otherwise specified by an authorized ADJ® service technician.
Replacing with anything other than the specified part can damage
your unit and will void your manufactures warranty.
Warning: If you continue to blow lamps or fuses, STOP using the
unit. Contact customer support for further instructions, you may have
to return the unit for servicing. Continuing to use the unit may cause
serious damage.
Fuse Replacement: First unplug the power. The fuse holder is
located next to the PowerCon connection. Using a flat-head screw
driver unscrew the fuse holder. Remove the bad fuse and replace with
a new one.
Lamp Replacement: Caution! Never attempt to change the lamp
while the fixture is plugged in. Always disconnect the main power
and allow the unit ample time to cool before attempting to replace
the lamp. Please see page 7 for important information regarding the
discharge lamp. See the next pages for lamp replacement instruc-
tions. Be sure to follow the proper handling procedures that deal
with discharge lamps.
Vizi Beam 5RX Photometric Chart
(LUX)
Distance(m)
Diameter(m)
ADJ Products, LLC - www.adj.com - Vizi Beam 5RX Instruction Manual Page 35ADJ Products, LLC - www.adj.com - Vizi Beam 5RX Instruction Manual Page 34
770000
0
5.0 10.0 20.0
0.41
220000
0.81
55000
1.6
5
0m( )
Vizi Beam 5RX Lamp Replacement
Vizi Beam 5RX Lamp Replacement
1. Remove the fixture head covers using a screwdriver (Figure 1).
Figure 1
2. Posion the head as Figure 2 and remove the lamp cooling fan at the rear of the head.
3. Li the lamp out of its recess as Figure 3.
Figure 3
4. Disconnect the lamp and connect the replacement lamp (Figure 4).
Figure 2
Figure 4
ADJ Products, LLC - www.adj.com - Vizi Beam 5RX Instruction Manual Page 36 ADJ Products, LLC - www.adj.com - Vizi Beam 5RX Instruction Manual Page 37
Vizi Beam 5RX Lamp Replacement
Vizi Beam 5RX Cleaning
Place the new lamp into the lamp recess.(Figure 5)
Figure 5
5. See illustraon below. Adjust the lamp using a sloed (flat head)
screwdriver unl it is centralized.
Fixture Cleaning: Due to fog residue, smoke, and dust cleaning
the internal and external optical lenses and mirror should be carried
out periodically to optimize light output. Cleaning frequency depends
on the environment in which the fixture operates (I.e. smoke, fog
residue, dust, dew). In heavy club use we recommend cleaning on a
monthly basis. Periodic cleaning will ensure longevity, and crisp output.
1. Use normal glass cleaner and a soft cloth to wipe down the out-
side casing.
2. Use a brush to wipe down the cooling vents and fan grill.
3. Clean the external optics and mirror with glass cleaner and a soft
cloth every 20 days.
4. Clean the internal optics with glass cleaner and a soft cloth every
30-60 days.
5. Always be sure to dry all parts completely before plugging the unit
back in.
Vizi Beam 5RX Trouble Shooting
Trouble Shooting: Listed below are a few common problems that
you may encounter, with solutions.
No light output from the unit;
Figure 6
6. Reinstall the fan and secure it, then replace and secure the head
covers before reapplying power.
ADJ Products, LLC - www.adj.com - Vizi Beam 5RX Instruction Manual Page 38
1. Be sure you have connected your unit into a standard 120v wall
outlet.
2. Be sure the external fuse has not blown. The fuse is located on
the bottom panel of the unit.
3. Remove the lamp holder and be sure the lamp is seated in its
socket properly. Occasionally lamps become loose during ship ping be sure the lamp is push in to its socket all the way.
4. Be sure the fuse holder is completely and properly seated.
Unit does not respond to sound;
1. Low frequencies (bass) should cause the unit to react to sound.
Pressping on the microphone, quiet or high pitched sounds may
not activate the unit.
ADJ Products, LLC - www.adj.com - Vizi Beam 5RX Instruction Manual Page 39
Vizi Beam 5RX Warranty
MANUFACTURER’S LIMITED WARRANTY
A. ADJ Products, LLC hereby warrants, to the original purchaser, ADJ Products, LLC products
to be free of manufacturing defects in material and workmanship for a prescribed period from
the date of purchase (see specific warranty period on reverse). This warranty shall be valid only if the
product is purchased within the United States of America, including possessions and
territories. It is the owner’s responsibility to establish the date and place of purchase by acceptable
evidence, at the time service is sought.
B. For warranty service you must obtain a Return Authorization number (RA#)
before sending back the product–please contact ADJ Products, LLC Service Department
at 800-322-6337. Send the product only to the ADJ Products, LLC factory. All
shipping charges must be pre-paid. If the requested repairs or service (including
parts replacement) are within the terms of this warranty, ADJ Products, LLC will pay return
shipping charges only to a designated point within the United States. If the entire instrument is
sent, it must be shipped in it’s original package. No accessories should be shipped with the product. If
any accessories are shipped with the product, ADJ Products, LLC shall have no liability whatsoever for
loss of or damage to any such accessories, nor for the safe return thereof.
C. This warranty is void if the serial number has been altered or removed; if the product is modified in any
manner which ADJ Products, LLC concludes, after inspection, affects the reliability of the product; if the
product has been repaired or serviced by anyone other than the ADJ Products, LLC factory unless prior
written authorization was issued to purchaser by ADJ Products, LLC; if the product is damaged because
not properly maintained as set forth in the instruction manual.
D. This is not a service contract, and this warranty does not include maintnance, cleaning or periodic check
up. During the period specified above, ADJ Products, LLC will replace defective parts at its expense
with new or refurbished parts, and will absorb all expenses for warranty service and repair labor by
reason of defects in material or workmanship. The sole responsibility of ADJ Products, LLC under this
warranty shall be limited to the repair of the product, or replacement thereof, including parts, at the sole
discretion of ADJ Products, LLC. All products covered by this warranty were manufactured after August
15, 2012, and bear indentifying marks to that effect.
E. ADJ Products, LLC reserves the right to make changes in design and/or improvements upon its products
without any obligation to include these changes in any products theretofore manufactured.
No warranty, whether expressed or implied, is given or made with respect to any accessory supplied with
products described above. Except to the extent prohibited by applicable law, all implied warranties made
by ADJ Products, LLC in connection with this product, including warranties of merchantability or fitness,
are limited in duration to the warranty period set forth above. And no warranties, whether expressed or
implied, including warranties of merchantability or fitness, shall apply to this product after said period
has expired. The consumer’s and/or Dealer’s sole remedy shall be such repair or replacement as is
expressly provided above; and under no circumstances shall ADJ Products, LLC be liable for any loss or
damage, direct or consequential, arising out of the use of, or inability to use, this product.
This warranty is the only written warranty applicable to ADJ Products, LLC Products and
supersedes all prior warranties and written descriptions of warranty terms and conditions heretofore
published.
MANUFACTURER’S LIMITED WARRANTY PERIODS:
•LightingProducts=1-year(365days)LimitedWarranty(Such as: Special Effect Lighting, Intelligent
Lighting, UV lighting, Strobes, Fog Machines, Bubble Machines, Mirror Balls, Par Cans, Trussing,
Lighting Stands etc. excluding LED and lamps)
•LaserProducts=1Year(365Days)LimitedWarranty(excluding laser diodes which have a 6 month
limited warranty)
•L.E.D.Products=2-year(730days)LimitedWarranty(excluding motors, PCB boards, and power
supplies, which have a 1-year (365 day Limited Warranty) batteries which have a 180 day limited war-
ranty). Only the L.E.D.s carry a 2-year warranty (excluding StarTec Series which a carries a 90 Day
Limited Warranty)
•ADJDMXControllers=2Year(730Days)LimitedWarranty(excluding faders and tact switches)
Vizi Beam 5RX Notes
ADJ Products, LLC - www.adj.com - Vizi Beam 5RX Instruction Manual Page 40 ADJ Products, LLC - www.adj.com - Vizi Beam 5RX Instruction Manual Page 41
Vizi Beam 5RX Specifications
Model: Vizi Beam 5RX
Voltage: 100~240V, 50/60Hz
Lamp: Philips® Platinum 5R Discharge*
Power Consumption: 273W
Power Cord Daisy Chain: 3 Fixtures Max. (120V)
6 Fixtures Max. (230V)
Dimensions: 15.5”(L) x 12.75”(W) x 20.5”(H)
394mm x 325mm x 522mm
Colors: 14 Plus White
Gobos: 17 + Spot
Weight: 42 Lbs. / 19 kgs.
Fuse: 7A
Duty Cycle: None
DMX: 16 or 19 Channels
Warranty: 1 Year (365 days)
*This lamp has a 3000 hour life please see page 7 for more info.
Auto Sensing Voltage: This xture contains a electronic bal-
last, which will auto sense the voltage when it is plugged into the
power source.
Please Note: Specications and improvements in the design
of this unit and this manual are subject to change without any
prior written notice.
ADJ Products, LLC - www.adj.com - Vizi Beam 5RX Instruction Manual Page 42
ADJ Products, LLC
6122 S. Eastern Ave. Los Angeles, CA 90040 USA
Tel: 323-582-2650 / Fax: 323-725-6100
Web: www.adj.com / E-mail: info@americandj.com
A.D.J. Supply Europe B.V.
Junostraat 2
6468 EW Kerkrade
Netherlands
service@adjgroup.eu / www.adj.eu
Tel: +31 45 546 85 00 / Fax: +31 45 546 85 99
Loading...