ADJ Vision VS2, Vision VS3, Vision VS5 User guide

VISION SERIES

LED VIDEO PANEL

VS2 VS3 VS5

User Manual

©2022 ADJ Products, LLC all rights reserved. Information, specications, diagrams, images, and

instructions herein are subject to change without notice. ADJ Products, LLC logo and identifying
product names and numbers herein are trademarks of ADJ Products, LLC. Copyright protection
claimed includes all forms and matters of copyrightable materials and information now allowed by
statutory or judicial law or hereinafter granted. Product names used in this document may be trade­marks or registered trademarks of their respective companies and are hereby acknowledged. All
non-ADJ Products, LLC brands and product names are trademarks or registered trademarks of their
respective companies.

ADJ Products, LLC and all aliated companies hereby disclaim any and all liabilities for property,

equipment, building, and electrical damages, injuries to any persons, and direct or indirect economic
loss associated with the use or reliance of any information contained within this document, and/or as
a result of the improper, unsafe, insucient and negligent assembly, installation, rigging, and opera­tion of this product.

DOCUMENT VERSION

Due to additional product features and/or enhancements, an updated version of
this document may be available online.
Please check www.adj.com for the latest revision/update of this manual
before beginning installation and/or programming.

Date

02/25/2020 1.0 N/A Not Applicable Initial Release.

10/12/2020 1.5 N/A Not Applicable Update Specifications.

02/04/2022 2.0 N/A Not Applicable

Europe Energy Saving Notice
Energy Saving Matters (EuP 2009/125/EC)

Saving electric energy is a key to help protecting the enviroment. Please turn o all electrical products when

they are not in use. To avoid power consumption in idle mode, disconnect all electrical equipment from power
when not in use. Thank you!

Document

Version

Software

Version

DMX Channels Notes

Update Optional Components and
Accessories, update formatting.

2

TABLE OF CONTENTS

General Information 4

Limited Warranty (USA Only) 6

Safety Guidelines 7

Maintenance Guidelines 9

Panel Overview 10

LED Module Removal Tool 12

LED Module Removal 13

Handling and Transportation 14

Installation 16

Horizontal Panel Assembly 17

Vertical Panel Assembly 18

Rigging Bar 19

Flat Panel Assembly 25

Horizontal Truss Mount 26

Ground Stack 27

Technical Specifications 28

Optional Components and Accessories 29

3

GENERAL INFORMATION

INTRODUCTION

Please read and understand the instructions in this manual carefully and thoroughly before attempting
to operate this device. These instructions contain important safety and use information.

ADJ’s Vision Series LED Video Panels oer the highest quality LED binning using 3-in-1 RGB SMD2121
LEDs, with a brightness of 1000 NITS. The primary dierence between models is the pixel pitch: the
VS2 has a pixel pitch of 2.97mm, the VS3 has a pixel pitch of 3.91mm, and the VS5 has a pixel pitch

of 5.95mm. All models have 4 individual modules for quick and easy front and rear accessible servic-

ing; are built on the same frame, allowing panels with dierent resolutions to be used together; use the
same rigging bar; all t into the same road case; and all have moveable integrated Corner Protectors

that safe-guard the corners when they are not connected. In addition, each Vision Series LED Video
Panel model has magnets located at the top and bottom to allow a user to temporarily connect two
panels, release his or her grip, and then securely latch them on the rear. This allows a single user to
install a full wall of panels.

The Vision Series LED Video Panel connections include Power In/Out and Data In/Out, and feature
built-in Novastar A5s receiving card. An optional VSFC8 Flight Case (purchased separately) can carry

up to 8x VS LED Video Panels, and an optional VSRB1 Rigging Bar (purchased separately) can hang

up to 20 VS LED Video Panels vertically.

ADJ oers full packages with video processors, software, cabling, rigging bars, and ight cases so

that you have everything you need to get up and running.

UNPACKING

Every Vision Series LED Video Panel has been thoroughly tested and has been shipped in perfect
operating condition. Carefully check the shipping carton for damage that may have occurred during
shipping. I the carton is damaged, carefully inspect the device for damage, and be sure all accessories
necessary to install and operate the device have arrived intact. In the event that damage has been
found or parts are missing, please contact our customer support team for further instructions. Please
do not return this device to your dealer without rst contacting customer support. Please do not dis­card the shipping carton in the trash. Please recycle whenever possible.

4

GENERAL INFORMATION

Customer Support: Contact ADJ Service for any product related service and support needs. Also visit

forums.adj.com with questions, comments or suggestions.

Parts: To purchase parts online visit:

http://parts.adj.com (US)
http://www.adjparts.eu (EU)

ADJ SERVICE USA - Monday - Friday 8:00am to 4:30pm PST
Voice: 800-322-6337 | Fax: [phone] | [e-mail]

ADJ SERVICE EUROPE - Monday - Friday 08:30 to 17:00 CET
Voice: [phone] | Fax: [phone] | [e-mail]

ADJ PRODUCTS LLC USA

6122 S. Eastern Ave. Los Angeles, CA. 90040
323-582-2650 | Fax [phone] | www.adj.com | [e-mail]

ADJ SUPPLY Europe B.V

Junostraat 2 6468 EW Kerkrade, The Netherlands

[phone] | Fax [phone]

www.americandj.eu | [e-mail]

ADJ PRODUCTS GROUP Mexico

AV Santa Ana 30 Parque Industrial Lerma, Lerma, Mexico 52000

[phone]

CAUTION! There are no user serviceable parts inside this unit. Do not attempt any repairs yourself,
as doing so will void your manufacturer’s warranty. In the unlikely event your unit may require service,
please contact ADJ Products, LLC.

Do not discard the shipping cartoon in the trash. Please recycle when ever possible.

5

LIMITED WARRANTY (USA ONLY)

A. ADJ Products, LLC hereby warrants, to the original purchaser, ADJ Products, LLC products to be free of

manufacturing defects in material and workmanship for a prescribed period from the date of purchase

(see specic warranty period on reverse). This warranty shall be valid only if the product is purchased

within the United States of America, including possessions and territories. It is the owner’s responsibility
to establish the date and place of purchase by acceptable evidence, at the time service is sought.

B. For warranty service, you must obtain a Return Authorization number (RA#) before sending the product

back—please contact ADJ Products, LLC Service Department at 800-322-6337. Send the product only to
the ADJ Products, LLC factory. All shipping charges must be prepaid. If the requested repairs or service
(including parts replacement) are within the terms of this warranty, ADJ Products, LLC will pay return ship­ping charges only to a designated point within the United States. If the entire instrument is sent, it must be
shipped in its original package and packaging material. No accessories should be shipped with the prod­uct. If any accessories are shipped with the product, ADJ Products, LLC shall incur no liability whatsoever
for loss of or damage to any such accessories, nor for the safe return thereof.

C. This warranty is void if the product serial number and/or labels are altered or removed; if the product is

modied in any manner which ADJ Products, LLC concludes, after inspection, aects the reliability of the

product; if the product has been repaired or serviced by anyone other than the ADJ Products, LLC factory
unless prior written authorization was issued to purchaser by ADJ Products, LLC; if the product is dam­aged because it was not properly maintained as set forth in the product instructions, guidelines and/or
user manual.

D. This is not a service contract, and this warranty does not include maintenance, cleaning, or periodic

checkup. During the period specied above, ADJ Products, LLC will replace defective parts at its expense
with new or refurbished parts, and will absorb all expenses for warranty service and repair labor by reason

of defects in material or workmanship. The sole responsibility of ADJ Products, LLC under this warranty
shall be limited to the repair of the product, or replacement thereof, including parts, at the sole discretion
of ADJ Products, LLC. All products covered by this warranty were manufactured after August 15, 2012,

and bear identifying marks to that eect.

E. ADJ Products, LLC reserves the right to make changes in design and/or improvements upon its products

without any obligation to include these changes in any products theretofore manufactured.

F. No warranty, whether expressed or implied, is given or made with respect to any accessory supplied with

products described above. Except to the extent prohibited by applicable law, all implied warranties made
by ADJ Products, LLC in connection with this product, including warranties of merchantability or tness,
are limited in duration to the warranty period set forth above. And all warranties, whether expressed or
implied, including warranties of merchantability or tness, are limited in duration to the warranty period set
forth above. The consumer’s and/or dealer’s sole remedy shall be such repair or replacement as is ex-

pressly provided above; and under no circumstances shall ADJ Product, LLC be liable for any loss and/or
damage, direct and/or consequential arising out of the use of, and/or inability to use this product.

G. This warranty is the only written warranty applicable to ADJ Products, LLC products, and supersedes all

prior warranties and written descriptions of warranty terms and conditions heretofore published.

MANUFACTURER’S LIMITED WARRANTY PERIODS:

• Non-LED Lighting Products = 1-Year (365 Days) (Including Special Eect Lighting, Intelligent Lighting,

UV lighting, Strobes, Fog Machines, Bubble Machines, Mirror Balls, Par Cans, Trussing, Lighting Stands,

Power/Data Distribution, etc. excluding LED and lamps)

• Laser Products = 1-Year (365 Days) (excluding laser diodes which have a 6-Month Limited Warranty)

• LED Products = 2-Year (730 Days) (excluding batteries which have a 180 Day Limited Warranty)

• NOTE: 2-Year (730 Days) Limited Warranty ONLY applies to product purchased within the United States.
StarTec Series = 1-Year (365 Days) (excluding batteries which have a 180 Day Limited Warranty)

• ADJ DMX Controllers = 2 Year (730 Days)

• American Audio Products = 1 Year (365 Days)

6

SAFETY GUIDELINES

The Vision Series LED Video Panel is a sophisticated piece of electronic equipment. To guarantee
smooth operation, it is important to follow all instructions and guidelines in this manual. ADJ is not
responsible for injury and/or damages resulting from the misuse of this panel due to the disregard of

the information printed in this manual. Only qualied and/or certied personnel should perform the

installation of this panel and all included rigging parts and/or accessories. Only the original included
rigging parts and/or rigging accessories for this panel should be used for proper installation. Any
modications to the panel, including to rigging and/or accessories, will void the original manufac­turer’s warranty and increase the risk of damage and/or personal injury.

PROTECTION CLASS 1 - PANEL MUST BE PROPERLY GROUNDED.

THERE ARE NO USER SERVICEABLE PARTS INSIDE THIS PANEL. DO NOT AT­TEMPT TO PERFORM ANY REPAIRS BY YOURSELF, AS DOING SO WILL VOID
YOUR MANUFACTURER’S WARRANTY. DAMAGES RESULTING FROM MODIFICA­TIONS TO THIS PANEL AND/OR THE DISREGARD OF SAFETY INSTRUCTIONS
AND GUIDELINES IN THIS MANUAL VOID THE MANUFACTURER’S WARRANTY
AND ARE NOT SUBJECT TO ANY WARRANTY CLAIMS AND/OR REPAIRS.

DO NOT PLUG PANEL INTO A DIMMER PACK!
NEVER OPEN THIS PANEL WHILE IN USE!
UNPLUG POWER BEFORE SERVICING PANEL!
NEVER TOUCH FRONT OF PANEL DURING OPERATION, AS IT MAY BE HOT!
KEEP FLAMMABLE MATERIALS AWAY FROM PANEL.

INDOOR / DRY LOCATIONS USE ONLY!
DO NOT EXPOSE PANEL TO RAIN AND/OR MOISTURE!
DO NOT SPILL WATER AND/OR LIQUIDS ON OR INTO THE PANEL!

7

SAFETY GUIDELINES

• DO NOT touch panel housing during operation. Turn OFF power and allow approximately 15 min­utes for panel to cool down before servicing.

• DO NOT operate devices with covers open and/or removed.

• DO NOT shake panel, and avoid brute force when installing and/or operating.

• DO NOT expose any part of the panel to open ame or smoke. Keep panel away from heat
sources such as radiators, heat registers, stoves, or other appliances (including ampliers) that

produce heat.

• DO NOT install/use in extremely hot/humid environments, or handle without ESD precautions.

• DO NOT exceed an operation temperature of 40°C (104°F), as doing so will result in damage to

the device.

• DO NOT operate if power cord is frayed, crimped, damaged, and/or if any of the power cord
connectors are damaged and do not insert into the panel securely and with ease. NEVER force
a power cord connector into the panel. If the power cord or any of its connectors are damaged,
replace immediately with a new cord and/or connector of the same power rating.

• DO NOT block air ventilation slots/vents. All fan and air inlets must remain clean and never
blocked.

• Allow approximately 6” (15cm) between panel and other devices or a wall for proper cooling.

• ALWAYS disconnect panel from main power source before performing any type of service and/or

cleaning procedure.

• Only handle the power cord by the plug end, and never pull out the plug by tugging the wire por­tion of the cord.

• ONLY use the original packaging materials and/or case to transport the panel in for service.

• PLEASE recycle shipping boxes and packaging whenever possible.

• To avoid causing physical damage, read the installation instructions carefully before installation.

• Panels should be installed/operated by qualied and trained professionals ONLY.

• Always mount panels in a safe and stable manner.

• INDOOR / DRY location use ONLY! Outdoor use will void the manufacturer’s warranty.

• Wear appropriate safety equipment during panel installation.

• Turn OFF power to panel, computers, servers, system boxes, and monitors before making any

type of power or data connections and before performing any maintenance work.

• Electronics used in this panel are ESD (Electrostatic Discharge) sensitive. To protect device from
ESD, wear a grounded ESD wrist strap or similar grounding device when handling panel.

• Panel must be properly grounded before operating. (resistance must be less than 4Ω)

• Ensure all power is disconnected from panel before unplugging any data cables from the panel,

especially serial line ports.

• Route power and data cables so that they are NOT likely to be walked on or pinched.

• Air conditioning is required if operating environment temperature exceeds 30°C (86°F).

• If panels are not in regular use for an extended period, it is advised to test run the devices for 2

hours each week to ensure that they remain in proper working condition.

• Cases used to transport panel must me properly waterproofed for transportation.

8

MAINTENANCE GUIDELINES

• Careful and regular maintenance is necessary to optimize the potential functional lifespan of the

Vision Series Series LED Video Panels.

• Read the installation and operation instructions for correct operation of the Vision Series LED

Video Panels.

• Although the Vision Series LED Video Panels are designed and built to withstand some impact

forces when installed correctly, care should still be taken to avoid impact damage when handling
or transporting them, especially at or near the corners and edges of the devices, which are par­ticularly susceptible to damage during transportation.

• The xture should be serviced by a qualied service technician when:

A. Objects have fallen onto, or liquid has been spilled into, the xture
B. The xture has been exposed to rain or water conditions in excess of IP rating parameters for

an IP20 device. This includes exposure from the front, rear, or side of the panels.

C. The xture does not appear to operate normally or exhibits a marked change in performance.
D. The xture has fallen and/or has been subjected to extreme handling.

• Check each Vision Series LED Video Panel for loose screws and other fasteners.

• If the Vision Series LED Video Panel installation is xed or displayed for a lengthy time, regularly

inspect all rigging and installation equipment, and replace or repair as necessary.

• During long periods of non-use, disconnect the main power to the unit.

• Use necessary ESD (electrostatic discharge) precautions when handling Vision Series LED Video

Panels, especially the LED screens, as they are ESD sensitive and easily damaged from ESD

exposure.

• The Null Line and Live Line connections from the computer and control system cannot be re-

versed and should therefore only be connected in original layout order.

• If the GFI (Ground Fault Interrupt) breaker-switch trips often, check the display or replace the

power-supply switch.

• When operating the Vision Series LED Video Panels, power up the computer before pow-

ering up the LED Video Panels. Conversely, when shutting down after operation, turn the

LEDVideoPanelsobeforeturningothecomputer.Ifthecomputeristurnedowhile

the panels are still powered on, a high intensity spike of brightness may occur, resulting in
catastrophic damage to the LEDs.

• If a circuit shorts out, a breaker-switch trips, wires burn, and or any other abnormality appears

while conducting an electrical test, discontinue testing, and troubleshoot units to nd the prob-

lem before continuing with any testing or operation.

• To ensure consistent operation, it might be necessary to learn operating parameters for installa-

tion, data recovery, backup, controller settings, and basic data preset modication.

• Regularly check computer for any viruses and remove any irrelevant data.

• Only a qualied technician should operate software system.

• Remove any moisture found inside or outside of any Vision Series LED Video Panels before dis-

mantling video installation and returning them to their optional ight cases (sold separately). En­sure ight cases are free of any moisture, using a fan to dry them if necessary, and avoid frictional

contact that may result in ESD generation when returning Vision Series LED Video Panels to the

ight cases.

• The Vision Series LED Video Panels are designed for indoor use only, within its IP20 rating pa-

rameters (front / rear). Limit or remove any unit exposed to moisture, condensation, or humidity,

and consider using air conditioning where available.

• When not in use, store Vision Series LED Video Panels in a dry, well ventilated facility.

9

PANEL OVERVIEW

DIMENSIONS: 19.75” x 19.75” x 3” (500mm x 500mm x 100mm)

10

PANEL OVERVIEW

Each Vision Series LED Video Panel includes a quick-release power supply with 4X LED Modules,
allowing for easy serviceability and simple repairs whilst out on the road, and each is held safely in

place with frame integrated magnets. The cover of the power supply box can be secured to pr

tect all internal accessories and components. All detachable components are secured with a safety
cable.

o-

11

LED MODULE REMOVAL TOOL

A technician can use the optional VSM111 Magnetic Module Removal Tool (sold separately) to
safely remove and reinstall any of the four LED Modules in the Vision Series LED Video Panel, and

minimize potential damage from mishandling, ESD exposure, or other issues.

The percieved “Magnetic Force” is relative to the distance the magnet is from the surface. Turning
the knob clockwise, in the “+” direction, advances the magnet, moving it closer to the front; turning
it counterclockwise, in the “-” direction, retracts the magnet, moving it away from the front.

The magnet must be fully retracted in the Magnet Module Removal Tool before
placing it against the LED Module face. This prevents the magnet from snapping
against the LEDs and damaging them.

12

LED MODULE REMOVAL

Note that the (4x) LED Modules are firmly held to the Vision Series LED Video Panel Frame with

strong integrated magnets, and secured with a safety cable should any of the LED modules be acci­dently knocked free.

Locate the center of selected LED module to be removed (1 of 4), and place the O-Ring of the
Magnetic Module Removal Tool against the surface of the module.

Turn the knob at the rear of the Magnetic Module Removal Tool to advance the magnet and secure
the LED Module. The Magnetic Module Removal Tool magnet is stronger than the magnets that
hold the LED Module to the Vision Series LED Video Panel frame, allowing the tool to pull the mod­ule from the frame. With the tool secured to the LED module, carefully pull the module free from the
video panel frame. When finished servicing the LED Module, reverse the operation. Be sure to reat­tach the safety cable to the LED Module.

13

HANDLING AND TRANSPORTATION

INTEGRATED CORNER PROTECTORS

The corners of the Vision Series LED Video Panels are susceptible to damage during handling and
transportation. When removing Vision Series LED Video Panels from their respective Flight Cases
(VSFC8 sold separately), and before they are installed, take care to avoid damaging any of the 4 cor­ners.

The integrated corner protectors rotate out of their respective housing pockets to protect the cor­ners during storage or transpotation (below right). During installation, these corner protectors can be
rotated back into their housing pockets to allow for the fitment of adjacent panels (below left).

14

HANDLING AND TRANSPORTATION

ELECTROSTATIC DISCHARGE (ESD) PRECAUTIONS

Because these are ESD sensitive units, ESD precautions must be observed when removing the
Vision Series LED Video Panels from their flight case (ESD gloves, protective clothing, wrist straps,
etc.). In addition to using standard ESD precautions, in order to reduce static building friction, take
care to lift the panels without rubbing the LED panel surface along the foam-covered slots, which
can generate static electricity that can damage LEDs on Vision Series LED Video Panels.

FLIGHT CASE

The optional VSFC8 Flight Case (sold separately) for the Vision Series LED Video Panels holds eight
(8) individual Vision Series LED Video Panels. The flight case features a full foam lining with slots for
each unit. The case is robust, offering complete protection for a set of panels on the road. Designed
specifically for use with Vision Series LED Video Panels, it is constructed from 9mm plywood and fit­ted with steel ball corners, aluminum edging, large swivel castors, professional butterfly latches, four
sprung handles, and a hinged lid.

15

INSTALLATION

DO NOT INSTALL THE PANEL IF YOU ARE NOT QUALIFIED TO DO SO!
INSTALLATION BY QUALIFIED TECHNICIANS ONLY!
INSTALLATIONS SHOULD BE CHECKED BY A QUALIFIED PERSON AT LEAST
ONCE A YEAR!

FLAMMABLE MATERIAL WARNING

Keep panel(s) a minimum of 5.0 feet (1.5m) away from ammable materials and/or

pyrotechnics.

ELECTRICAL CONNECTIONS
A qualied electrician should be used for all electrical connections and/or instal­latons.

A MAXIMUM OF 20 PANELS may be suspended from each other in a vertical
column. There is no limit on the number of panels that may be installed in a single
horizontal row. Note that additional processing power may be necessary to oper­ate larger quantities of panels.

USE CAUTION WHEN POWER LINKING PANELS OF DIFFERENT MODEL TYPES,
AS POWER CONSUMPTION CAN VARY WITH MODEL TYPE, AND MAY EXCEED
THE MAX POWER OUTPUT OF THIS PANEL. CONSULT THE SILK SCREEN FOR
MAX CURRENT RATING.

Input Power AC 100-240VAC, 50/60Hz, 16A Max

Output Power AC 100-240VAC, 50/60Hz, 14A Max

Max Power Consumption 170W Max, 68W Average

• WARNING! The safety and suitability of any lifting equipment, installation location/platform, anchor-
ing/rigging/mounting method and hardware, and electrical installation is the sole responsibility of the
installer.

• Panel(s) and all panel accessories and all anchoring/rigging/mounting hardware MUST be installed fol-
lowing all local, national, and country commercial electrical and construction codes and regulations.

• Before rigging/mounting a single panel or multiple interconnected panels to any metal truss/structure,
a professional equipment installer MUST be consulted to determine if the metal truss/structure or

surface is properly certied to safely hold the combined weight of the panels(s), clamps, cables, and

all accessories.

• Inspect metal truss/structure visually to ensure it does not ex and/or become deformed due to the

weight of the panel(s). Damage caused to panel(s) by mechanical stress is not covered by warranty.

• Panel(s) should be installed in areas outside walking paths, seating areas, and areas where unauthor­ized personnel might reach the panel(s) by hand. Access under work area must be blocked.

• NEVER stand directly below the panel(s) when rigging, removing, or servicing.

• OVERHEAD RIGGING: Overhead xture installation must always be secured with a secondary safety

attachment, such as an appropriately rated safety cable. Overhead rigging requires extensive experi­ence, including calculating working load limits, knowledge of the installation material being used, and

periodic safety inspection of all installation material and the xture itself, among other skills. If you lack
these qualications, do not attempt the installation yourself. Improper installation can result in bodily

injury and property damage.

16

HORIZONTAL PANEL ASSEMBLY

1. The horizontal tab-keyed connector is
spring loaded.

3. Rotate the handle to the right (clock­wise) to hold the horizontal tab-keyed
connector in place.

2. Press the horizontal tab-keyed connec­tor until the tab-key passes through the
tab-keyed socket.

4. Rotate handle downward (counter­clockwise) to cinch the horizontal tab­keyed connector.

5. To unlock, rotate handle clockwise, re­leasing the tension of the horizontal tab­keyed connector cinching mechanism.

17

VERTICAL PANEL ASSEMBLY

1. Align the vertical positional posts with
their corresponding alignment holes.

3. Release the latch, then lock the panel in place by twisting the vertical connector

lever to the left, towards the direction marked “LOCKED”.

2. Press the spring-loaded locking latch
toward the left while pressing the verti­cal connector upwards into the locking
latch.

4. To unlock, twist the vertical connector lever to the right, towards the direction

marked “OPEN”. The locking post will then drop out of place.

18

RIGGING BAR

The Vision Series LED Video Panel is compatible with ADJ’s VSRB1 Rigging Bar (sold separately),
which easily and securely locks to the top of the rst panel in a vertical column of up to 20 Vision Se­ries LED Video Panels, allowing them hang from a truss, hoist, or lintel beam. Aqualiedtechnician

ortrainedprofessionalisrequiredtoytheVSRB1RiggingBar/VSLEDVideoPanelassembly.

19

RIGGING BAR

Vertical “hang” and “stack” congurations are illustrated below with the rigging bar.

20

VERTICAL HANG CONFIGURATION

RIGGING BAR

1. Align the vertical positional posts with
their corresponding alignment holes.

3. Release latch to hold the vertical connector, and twist vertical connector the left to lock.

2. Press spring-loaded locking latch to the
left while pressing vertical connector up
into locking latch.

4. To unlock the vertical connector, rotate the lever to the right (counter-clockwise), then
press the spring-loaded locking latch inward. The vertical connector will then drop open.

21

RIGGING BAR

VERTICAL HANG CONFIGURATION FOR SINGLE INSTALLER

The Vision Series LED Video Panels feature built-in magnets to assist in vertical hanging for a single
installation technician.

THE MAGNETS ARE NOT STRONG ENOUGH TO HOLD A PANEL WITHOUT AS­SISTANCE. ALWAYS SUPPORT THE PANEL BY HOLDING AND MAINTAINING
UPWARD PRESSURE ON AT LEAST ONE LIFTING HANDLE AT ALL TIMES UNTIL
THE PANEL IS LOCKED IN PLACE, STARTING WITH THE OPPOSITE VERTICAL
LOCK.

22

RIGGING BAR

VERTICAL HANG CONFIGURATION FOR SINGLE INSTALLER

23

VERTICAL STACK CONFIGURATION

RIGGING BAR

1. Align the vertical positional posts with
their corresponding alignment holes,
then insert the posts into the holes.

3. Release latch to hold the vertical connector. Lock in place by twisting the vertical
connector to the left.

2. Press spring-loaded locking latch to
the left while pressing vertical connec­tor upwards into locking latch.

4. To unlock the vertical connector, rotate the lever to the right (counter-clockwise),
then press the spring-loaded locking latch inward. The vertical connector will
drop open.

USE CAUTIONS WHEN INSTALLING VIDEO PANELS USING THE RIGGING BAR
FOR STACKED ASSEMBLIES. THESE DEVICES ARE NOT INTENDED FOR USE
AS A FREE-STANDING ASSEMBLY, AND ARE INHERENTLY UNSTABLE. STACKED
VIDEO PANEL ASSEMBLIES MUST BE SECURELY INSTALLED BY A QUALIFIED
TECHNICIAN ONLY!

24

FLAT PANEL ASSEMBLY

Rear Support Bracket: Use an VS1RSB Rear Support Bracket (sold separately) when connect­ing multiple panels for a larger display design, in order to strengthen the structural integrity of the

screen, improve consistent atness, and improve overall screen continuity.

25

HORIZONTAL TRUSS MOUNT

The optional VSR210 Horizontal Truss Mounting Bracket (sold separately) allows for the horizontal
(ceiling) installation of the VS LED Video Panels.

26

GROUND STACK

The optional VSSCSB single panel rigging / ground stack bar is a free-standing stack mounting op­tions for the Vision Series LED Video Panels.

27

TECHNICAL SPECIFICATIONS

GENERAL

Resolution

• VS2: 168(H) x 168(V)

• VS3: 128(H) x 128(V)

• VS5: 84(H) x 84(V)
Pixel Pitch:

• VS2: 2.97mm (0.12”)

• VS3: 3.91mm (0.15”)

• VS5: 5.95mm (0.23”)
LED Conguration: SMD212
Pixel Density:

• VS2: 112896 pixels/m

• VS3: 65536 pixels/m

• VS5: 28224 pixels/m

2

2

2

Size:

• 19.68” x 19.68” x 2.74”

• (500mm x 500mm x 69.6mm)
Module Quantity: 4
Weight: 17.0 lbs (7.7 kgs)

MECHANICAL RATINGS

Surface Flatness: Gap < 0.5mm

OPTICAL RATINGS

Brightness: 1000 cd/m

2

Viewing Angle: 160° / 140°
Viewing Distance:

• VS2: 3m

• VS3: 4m

• VS5: 6m
Gray Scale: > 14bits
Display Colors: 256
Contrast Ratio: 5000:1
Brightness Adjustment: 0~100%, 100 levels

CONTROL SYSTEMS

Control Mode: Constant Current Driving
Frame Update Frequency: 50~75Hz
Scan Mode:

• VS2: 1/21 duty

• VS3: 1/16 duty

• VS5: 1/7 duty
Refresh Rate: 3840 Hz
Support Input: RJ45
Control Distance:

• Ethernet Cable < 120m

• Fiber Optoc > 120m
Support VGA Mode:

• 1024x768

• 1280x1024

• 1600x1200

• 1920x1280
Brightness Correction:

• Pixel

• Module

• Cabinet

ENVIRONMENTAL

Operating Temp: -20° ~ +40° C / -4° ~ +104° F
Operating Humidity: 10~90% RH, no condensation
Operating Life: 50,000 hours
MTBF: 5000 hours
Protection Level: IP20
Out of Control Rate: < 0.02%
Curve Angle: n/a

POWER SUPPLY

Operation Power: 100~240V 50~60Hz
Max Power Consumption: 170W per panel
Average Power Consumption:

• VS2: 68W per panel

• VS3: 101W per panel

• VS5: 94W per panel
Power/Data Connections:

• Power In/Out

• Data In/Out

Specicationssubjecttochangewithoutanypriorwrittennotice.

28

OPTIONAL COMPONENTS AND ACCESSORIES

SKU NUMBER DESCRIPTION

VSFC8 Flight Case - ts 8 Vision Series LED Video Panels

VSRB1 Single Panel Rigging/Stack Bar

VS1RSB Rear Support Bracket

VSS225 (VSSCSB) Single Column Support Base

VSGSB Ground Support Base

VSGSCSB Clamp Support Bar

VSGSLT Ground Support Ladder Truss

VSM111 (VSMRT) Magmetic Module Removal Tool

VSR210 Horizontal Truss Mounting Bracket

VX4001 Novastar VX4S Video Processor

MCT300 Novastar MCTRL-3000 Video Processor

MED500 ArKaos Media Master Express Video Software

MED552 ArKaos Media Master Pro 5 (License)

MED223 ArKaos Studio Server

MED234 ArKaos Stadium Server

MED245 ArKaos 4K Server

MED212 ArKaos Stage Server Pro

MED201 ArKaos Stage Server Express

MPC010 (10 ft)

MPC015 (15 ft)

MPC025 (25 ft)

MPC050 (50 ft)

PLC1 (1 ft)

PLC3 (3 ft)

PLC6 (6 ft)

PLC10 (10 ft)

PLC15 (15 ft)

PLC25 (25 ft)

CAT6PRO5 (5 ft)

CAT6PRO10 (10 ft)

CAT6PRO15 (15 ft)

CAT6PRO25 (25 ft)

CAT6PRO50 (50 ft)

Main Power Cables - Locking Power Connector In/Out to Edison

Panel to Panel Power Link Cable - Locking Power Connector In/Out
to Locking Power Connector In/Out

Main Data Cable - Bare RJ45 to Locking RJ45 Ethernet Connection
In/Out

CAT6PRO100 (100 ft)

CAT6PRO150 (150 ft)

CAT6PRO25FC (25 ft)

CAT6PRO50FC (50 ft)

CAT6PRO100FC (100 ft)

Panel to Panel Data Link Cable - Locking RJ45 Ethernet Connection
In/Out to Locking RJ45 Ethernet Connection In/Out

29