ADJ UV Flood 36 Users Manual

UV FLOOD 36

©2015 ADJ Products, LLC all rights reserved. Information,

specications, diagrams, images, and instructions herein are
subject to change without notice. ADJ Products, LLC logo and
identifying product names and numbers herein are trademarks
of ADJ Products, LLC. Copyright protection claimed includes all
forms and matters of copyrightable materials and information
now allowed by statutory or judicial law or hereinafter granted.
Product names used in this document may be trademarks or
registered trademarks of their respective companies and are
hereby acknowledged. All non-ADJ Products, LLC brands and
product names are trademarks or registered trademarks of their

respective companies.

ADJ Products, LLC and all aliated companies hereby dis­claim any and all liabilities for property, equipment, building, and
electrical damages, injuries to any persons, and direct or indi­rect economic loss associated with the use or reliance of any
information contained within this document, and/or as a result
of the improper, unsafe, unsucient and negligent assembly,
installation, rigging, and operation of this product.

Rev. 11/15

User Instructions

Europe Energy Saving Notice
Energy Saving Matters (EuP 2009/125/EC)
Saving electric energy is a key to help protecting the enviroment.
Please turn o all electrical products when they are not in use. To
avoid power consumption in idle mode, disconnect all electrical
equipment from power when not in use. Thank you!

UV Flood 36 Introduction

UV Flood 36 General Instructions

Unpacking: Thank you for purchasing the UV Flood 36 by ADJ Prod-

ucts, LLC. Every UV Flood 36 has been thoroughly tested and has
been shipped in perfect operating condition. Carefully check the ship­ping carton for damage that may have occurred during shipping. If the
carton appears to be damaged, carefully inspect your xture for any
damage and be sure all accessories necessary to operate the unit has
arrived intact. In the case damage has been found or parts are miss­ing, please contact our toll free customer support number for further
instructions. Do not return this unit to your dealer without rst contact­ing customer support.

Introduction: The UV Flood 36 is part of ADJ’s continuing pursuit for

creating high quality affordable intelligent fixtures. The UV Flood 36 is
a DMX intelligent LED color wash. This wash can be used in a stand
alone mode or connected in a Master/Slave conguration. This unit has
three operating modes: sound active mode, dimmer mode, and DMX

controlled.

Customer Support: ADJ Products, LLC provides a toll free cus-

tomer support line, to provide set up help and to answer any question
should you encounter problems during your set up or initial operation.
You may also visit us on the web at www.adj.com for any comments
or suggestions. Service Hours are Monday through Friday 8:00 a.m. to
4:30 p.m. Pacic Standard Time.
Voice: [phone]
Fax: [phone]
E-mail: [e-mail]
To purchase parts online visit http://parts.americandj.com

Warning! To prevent or reduce the risk of electrical shock or re, do

not expose this unit to rain or moisture.

To optimize the performance of this product, please read these
operating instructions carefully to familiarize yourself with the basic
operations of this unit. These instructions contain important safety
information regarding the use and maintenance of this unit. Please
keep this manual with the unit, for future reference.

UV Flood 36 Features

• 3 Operating Modes: Sound Active Mode, Dimmer Mode, and DMX
Controlled

• Electronic Dimming 0-100%

• Built in Microphone

• DMX-512 protocol

• 3 DMX Channel Modes: 1 Channel Mode, 2 Channel Mode, & 3
Channel Mode

UV Flood 36 Warranty Registration

The UV Flood 36 carries a 2 year (730 days) limited warranty. Please
fill out the enclosed warranty card to validate your purchase and war-

ranty. You may also register your product online at www. americandj.
com. All returned service items whether under warranty or not, must

be freight pre-paid and accompany a return authorization (R.A.) num­ber. If the unit is under warranty you must provide a copy of your
proof of purchase invoice. Please contact ADJ customer support for a
R.A. number.

UV Flood 36 Cleaning

Due to fog residue, smoke, and dust cleaning the internal and exter­nal optical lenses must be carried out periodically to optimize light
output.

Caution! There are no user serviceable parts inside this unit. Do not

attempt any repairs yourself, doing so will void your manufactures war­ranty. In the unlikely event your unit may require service please contact
ADJ Products, LLC.

PLEASE recycle the shipping carton when ever possible.

ADJ Products, LLC - www.adj.com - UV Flood 36 Instruction Manual Page 2

1. Use normal glass cleaner and a soft cloth to wipe down the
outside casing.

2. Clean the external optics with glass cleaner and a soft cloth
every 20 days.

3. Always be sure to dry all parts completely before plugging
the unit back in.
Cleaning frequency depends on the environment in which the fixture
operates (i.e. smoke, fog residue, dust, dew).

ADJ Products, LLC - www.adj.com - UV Flood 36 Instruction Manual Page 3

UV Flood 36 Safety Precautions

UV Flood 36 Set Up

• To reduce the risk of electrical shock or re, do not expose this unit
rain or moisture

• Do not spill water or other liquids into or on to your unit.

• Be sure that the local power outlet match that of the required volt­ age for your unit.

• Do not attempt to operate this unit if the power cord has been
frayed or broken. Do not attempt to remove or break o the ground
prong from the electrical cord. This prong is used to reduce the risk
of electrical shock and re in case of an internal short.

• Disconnect from main power before making any type of connection.

• Do not remove the cover under any conditions. There are no user
serviceable parts inside.

• Never operate this unit when it’s cover is removed.

• Never plug this unit in to a dimmer pack

• Always be sure to mount this unit in an area that will allow proper
ventilation. Allow about 6” (15cm) between this device and a wall.

• Do not attempt to operate this unit, if it becomes damaged.

• This unit is intended for indoor use only, use of this product out`
doors voids all warranties.

• During long periods of non-use, disconnect the unit’s main power.

• Always mount this unit in safe and stable matter.

• Power-supply cords should be routed so that they are not likely to
be walked on or pinched by items placed upon or against them,
paying particular attention to the point they exit from the unit.

• Cleaning -The fixture should be cleaned only as recommended by
t he manufacturer. See page 3 for cleaning details.

• Heat -The appliance should be situated away from heat sources
such as radiators, heat registers, stoves, or other appliances (inclu­ d ing amplifiers) that produce heat.

• The fixture should be serviced by qualified service personnel when:
A. The power-supply cord or the plug has been damaged.
B. Objects have fallen, or liquid has been spilled into the appliance.
C. The appliance has been exposed to rain or water.
D. The appliance does not appear to operate normally or exhibits a
marked change in performance.

Power Supply: The ADJ UV Flood 36 contains a automatic voltage

switch, which will auto sense the voltage when it is plugged into the
power source. With this switch there is no need to worry about the cor­rect power voltage, this unit can be plugged in anywhere.

DMX-512: DMX is short for Digital Multiplex. This is a universal pro-

tocol used as a form of communication between intelligent fixtures
and controllers. A DMX controller sends DMX data instructions from
the controller to the fixture. DMX data is sent as serial data that trav­els from fixture to fixture via the DATA “IN” and DATA “OUT” XLR ter­minals located on all DMX fixtures (most controllers only have a DATA
“OUT” terminal).

DMX Linking: DMX is a language allowing all makes and models of
dierent manufactures to be linked together and operate from a single
controller, as long as all xtures and the controller are DMX compli­ant. To ensure proper DMX data transmission, when using several
DMX fixtures try to use the shortest cable path possible. The order
in which fixtures are connected in a DMX line does not influence the
DMX addressing. For example; a fixture assigned a DMX address of 1
may be placed anywhere in a DMX line, at the beginning, at the end,
or anywhere in the middle. When a fixture is assigned a DMX address
of 1, the DMX controller knows to send DATA assigned to address 1
to that unit, no matter where it is located in the DMX chain.

Data Cable (DMX Cable) Requirements (For DMX Operation):

The UV Flood 36 can be controlled via DMX-512 protocol. The UV Flood
36 has 3 DMX channel modes; 1 channel mode, 2 channel mode, &
3 channel mode. The DMX address is set on the rear panel of the UV
Flood 36. Your unit and your DMX controller require a approved DMX­512 110 Ohm Data cable for data input and data output (Figure 1). We
recommend Accu-Cable DMX cables. If you are
making your own cables, be sure to use standard
110-120 Ohm shielded cable (This cable may be
purchased at almost all professional sound and
lighting stores). Your cables should be made with
a male and female XLR connector on either end
of the cable. Also remember that DMX cable must
be daisy chained and cannot be split.

Figure 1

ADJ Products, LLC - www.adj.com - UV Flood 36 Instruction Manual Page 4

ADJ Products, LLC - www.adj.com - UV Flood 36 Instruction Manual Page 5

UV Flood 36 Set Up

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

DMX512

DMX+,DMX-,COMMON

1

2

3

Termination reduces signal errors and
avoids signal transmission problems
and interference. It is always advisable
to connect a DMX terminal, (Resistance
120 Ohm 1/4 W) between PIN 2 (DMX-)
and PIN 3 (DMX +) of the last fixture.

POWER

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

UV Flood 36 Operating Instructions

Notice: Be sure to follow gures two and three when making your own

cables. Do not use the ground lug on the XLR connector. Do not con­nect the cable’s shield conductor to the ground lug or allow the shield
conductor to come in contact with the XLR’s outer casing. Grounding
the shield could cause a short circuit and erratic behavior.

COMMON

1

DMX512 IN

3

3-PIN XLR

2

Figure 2

XLR Pin Conguration

Pin 1 = Ground

Pin 2 = Data Compliment (negative)

Pin 3 = Data True (positive)

When longer runs of cable are

Figure 4

Pin 1

Pin 2

Pin 3

Do Not Use

Do Not Use

XLR Male Socket

1 Ground

DMX512 OT

3-PIN XLR

2 Cold

3 Hot

1

3

2

DMX +

DMX -

XLR Female Socket

2 Cold

1 Ground

3 Hot

Figure 3

Special Note: Line Termination.

used, you may need to use a terminator on the last unit to avoid erratic
behavior. A terminator is a 110-120 ohm 1/4 watt resistor which is con­nected between pins 2 and 3 of a male XLR connector (DATA + and
DATA -). This unit is inserted in the female XLR connector of the last
unit in your daisy chain to terminate the line. Using a cable terminator
(ADJ part number Z-DMX/T) will decrease the possibilities of erratic
behavior.

5-Pin XLR DMX Connectors.

connectors for DATA transmission in place of 3-pin. 5-pin XLR xtures
may be implemented in a 3-pin XLR DMX line. When inserting stan­dard 5-pin XLR connectors in to a 3-pin line a cable adaptor must be
used, these adaptors are readily available at most electric stores. The
chart below details a proper cable conversion.

Conductor 5-Pin XLR Male (In)3-Pin XLR Female (Out)

Ground/Shield

Data Compliment (- signal)

Data True (+ signal)

Not Used

Not Used

ADJ Products, LLC - www.adj.com - UV Flood 36 Instruction Manual Page 6

Termination reduces signal errors and

1

avoids signal transmission problems

3

and interference. It is always advisable

2

to connect a DMX terminal, (Resistance
120 Ohm 1/4 W) between PIN 2 (DMX-)
and PIN 3 (DMX +) of the last fixture.

Some manufactures use 5-pin XLR

3-Pin XLR to 5-Pin XLR Conversion

Pin 1

Pin 2

Pin 3

The display will lock and blackout after 30 seconds, press
the MODE button for 3 seconds to unlock.

DMX Mode:

Operating through a DMX controller give the user the freedom to cre­ate their own programs tailored to their own individual needs. The UV
Flood 36 has 3 DMX modes: 1 Channel Mode, 2 Channel Mode, and
3 Channel Mode.

1. This function will allow you to control each individual fixture’s
traits with a standard DMX-512 controller. See pages 10-11 for
detailed description of the DMX values, and traits.

2. To control your fixture in DMX mode, follow the set-up procedures
on pages 5-6 as well as the set-up specifications that are includ­ ed with your DMX controller.

3. Press the MODE button until “AXXX” is displayed. “XXX” is the
represents the current DMX address. Use the UP and DOWN but­ tons to set your desired DMX address.

4. After you have set your desired DMX address, press the ENTER
button to select your desired DMX channel mode. “CHXX” will be
displayed. “XX” represent the current DMX channel mode. Use
the UP and DOWN buttons to find your desired DMX channel

mode.

5. Once you have set your DMX address and DMX channel mode,
use your DMX controller’s faders to control the various DMX fix­ ture traits.

6. For longer cable runs (more than a 100 feet) use a terminator on
the last fixture.

Static Mode:

In this mode the UV light will remain static. You can adjust the inten­sity in this mode as well.

1. Plug the fixture in and press the MODE button until “LXXX” is dis-

played.

2. Press the UP or DOWN buttons to adjust the intensity of the light.

3. Press the ENTER button and “S-XX” will be displayed. This is the
strobe mode. Use the UP or DOWN buttons to adjust the strobe

speed.

ADJ Products, LLC - www.adj.com - UV Flood 36 Instruction Manual Page 7

UV Flood 36 Operating Instructions

UV Flood 36 Operating Instructions

Sound Active Mode:

In this mode the UV Flood 36 will react to sound.

1. Plug the fixture in and press the MODE button until “SoXX” is
displayed. “XX” represents the sound sensitivity level. Use the UP
and DOWN buttons to adjust the sensitivity. “00” is the lowest
sensitivity, “30” is the highest.

Dimming Curve:

This is used to set the dimming curve used with DMX mode. See
page 11 for the dimming curves diagram.

1. Plug the fixture in and press the MODE button until the DMX

address is displayed.

2. Press the ENTER button until “dCXX” is displayed. This is the
dimmer setting. “XX” represents the current dimming mode.

3. Use the UP and DOWN buttons to find your desired dimmer
curve. Press SET UP when you are finished.

• dC00 - Standard

• dC01 - Stage

• dC02 - TV

• dC03 - Architectural

• dC04 - Theater

DMX State:

This mode is used as a precaution mode, that in case the DMX signal
is lost, the operating mode chosen in this setup is the running mode
the xture will go into when the DMX signal is lost. You can also set this
as the operating mode you would like the unit to return to when power

is applied.

1. Press the MODE button until the DMX address is displayed. Press
the ENTER button until either “Soun”, “HOLd”, or “blC” is dis-

played.

2. Use the UP or DOWN buttons to nd the mode you want incase
of power loss or DMX loss.

• “blC” (Blackout) - If the DMX signal is lost or interrupted, the unit will
automatically go into stand by mode.

• “HOLd” (Last State) - If the DMX signal is lost or interrupted, the x-

ture will stay in the last DMX set up. If power is applied and this mode
is set, the unit will automatically go into the last DMX set up.

• “Soun” (Sound Active) - If the DMX signal is lost or interrupted, the
unit will automatically go into sound active mode.

3. Find your desired setting and press ENTER. Your setting will be
saved automatically.

Activate RF Control:

This function is used to activate and deactivate the RF Remote
Control. When this function is activated you can control the fixture
using the Dotz Par RF remote. Please see the next page for remote
controls and functions.

1. Plug the fixture in and press the MODE button until “rFXX” is dis-
played. “XX” represents either “on” or “oFF”.

2. Press the UP or DOWN buttons to either activate the remote func­ tion (On) or deactivate it (Off).

UV Flood 36 Master-Slave Configuration

Master-Slave Configuration:

This function will allows you to link units together to run in a Master­Slave mode. In Master-Slave configuration one unit will act as the

controlling unit and the others will react to the controlling units built-in
programs. Any unit can act as a Master or as a Slave however, only

one unit can be programmed to act as the “Master.”

Master-Slave Connections and Settings:

1. Daisy chain your units via the XLR connector on the rear of the
unit. Use standard XLR microphone cables to link your units to-
gether. Remember that the Male XLR connector is the input and
the Female XLR connector is the output. The first unit in the
chain (master) will use the female XLR connector only. The last
unit in the chain will use the male XLR connector only.

2. Using the Master unit, choose your desired operating mode and
connect the “Slave” unit or units.

3. On the “Slave” unit(s) press the MODE button until a “SLAV” is
displayed. They will now follow the “Master” unit.

ADJ Products, LLC - www.adj.com - UV Flood 36 Instruction Manual Page 8

ADJ Products, LLC - www.adj.com - UV Flood 36 Instruction Manual Page 9

UV Flood 36 Dotz RF Remote Operation

The Dotz Par RF remote (sold separately) has many different func­tions and allows you to control your UV Flood 36 from long distance.
The remote can control your system up to 25 meters. To use the
remote you must first activate the fixtures receiver, to activate the re­ceiver please see the instructions on page 9.

BLACKOUT - Pressing this button will blackout the fixture.

COLOR - This button will activate the UV output. Use the “+” and “-”

buttons to adjust the output intensity.

SOUND ACTIVE - This button activates sound active mode.

UV Flood 36 1 Channel Mode

Channel Value Function

1 DIMMER

0 - 255 0% - 100%

UV Flood 36 2 Channel Mode

Channel Value Function

1 DIMMER

0 - 255 0% - 100%

2 STROBING
0 - 31 LED ON
32 - 95 STROBING SLOW - FAST
96 - 127 LED ON
128 - 159 PULSE STROBE SLOW - FAST
160 - 191 LED ON
192 - 223 RANDOM STROBE SLOW - FAST
224 - 255 SOUND ACTIVE STROBING

UV Flood 36 3 Channel Mode

Channel Value Function

1 DIMMER

0 - 255 0% - 100%

2 STROBING
0 - 31 LED ON
32 - 95 STROBING SLOW - FAST
96 - 127 LED ON
128 - 159 PULSE STROBE SLOW - FAST
160 - 191 LED ON
192 - 223 RANDOM STROBE SLOW - FAST
224 - 255 SOUND ACTIVE STROBING
3 DIMMER CURVES
0 - 20 STANDARD
21 - 40 STAGE
41 - 60 TV
61 - 80 ARCHTECTURAL
81 - 100 THEATRE
101 - 255 DEFAULT TO UNIT CURRENT SETTING

UV Flood 36 Dimmer Curve Chart

ADJ Products, LLC - www.adj.com - UV Flood 36 Instruction Manual Page 10

Ramp Effect

Standard

Stage

TV

Architectural

Theatre

ADJ Products, LLC - www.adj.com - UV Flood 36 Instruction Manual Page 11

(Fade Time) (Fade Time)

UV Flood 36 Photometric Chart

UV Flood 36 Power Cord Daisy Chain

Beam angle 57°
Field angle 93°

Intensity(LUX)

3

2

1

0

1

Beam opening(m)

2

3

0 1 2 3 4 5

Diameter

(m)

Diameter

(m)

201 45 18 9 4UV LEDs

1.09

2.11

2.17

4.22

With this feature you can connect the xtures to one another

using the I.E.C. input and output sockets. The quantity that can

be connected is 26 xtures maximum for 120V and 57 xtures
maximum for 230V. After the maximum xtures has been reached

you will need to use a new power outlet. They must be the same

xtures. DO NOT mix xtures.

UV Flood 36 Fuse Replacement

First unplug the power. Locate and remove the unit’s power cord.
Once the cord has been removed located the fuse holder located
inside the power socket. Insert a flat-head screw driver into the power
socket and gently pry out the fuse holder. Remove the bad fuse and
replace with a new one. The fuse holder has a built-in socket for a

57

93

spare fuse be sure not to confuse the spare fuse with active fuse.

UV Flood 36 Trouble Shooting

Listed below are a few common problems the user may encounter,
with solutions.

Unit not responding to DMX:

1. Check that the DMX cables are connected properly and are

3.26 4.34 5.4357°

6.32 8.43 10.5393°

wired correctly (pin 3 is “hot”; on some other DMX devices
pin 2 may be ‘hot’). Also, check that all cables are connected
to the right connectors; it does matter which way the inputs
and outputs are connected.

ADJ Products, LLC - www.adj.com - UV Flood 36 Instruction Manual Page 12

Unit does not respond to sound:

1. Quiet or high pitched sounds will not activate the unit.

ADJ Products, LLC - www.adj.com - UV Flood 36 Instruction Manual Page 13

UV Flood 36 Warranty

MANUFACTURER’S LIMITED WARRANTY

A. ADJ Products, LLC hereby warrants, to the original purchaser, ADJ Products, LLC products
to be free of manufacturing defects in material and workmanship for a prescribed period from
the date of purchase (see specific warranty period on reverse). This warranty shall be valid only if the
product is purchased within the United States of America, including possessions and
territories. It is the owner’s responsibility to establish the date and place of purchase by acceptable
evidence, at the time service is sought.

B. For warranty service you must obtain a Return Authorization number (RA#)

before sending back the product–please contact ADJ Products, LLC Service Department
at 800-322-6337. Send the product only to the ADJ Products, LLC factory. All

shipping charges must be pre-paid. If the requested repairs or service (including
parts replacement) are within the terms of this warranty, ADJ Products, LLC will pay return
shipping charges only to a designated point within the United States. If the entire instrument is
sent, it must be shipped in it’s original package. No accessories should be shipped with the product. If
any accessories are shipped with the product, ADJ Products, LLC shall have no liability whatsoever for
loss of or damage to any such accessories, nor for the safe return thereof.

C. This warranty is void if the serial number has been altered or removed; if the product is modified in any
manner which ADJ Products, LLC concludes, after inspection, affects the reliability of the product; if the
product has been repaired or serviced by anyone other than the ADJ Products, LLC factory unless prior
written authorization was issued to purchaser by ADJ Products, LLC; if the product is damaged because
not properly maintained as set forth in the instruction manual.

D. This is not a service contract, and this warranty does not include maintnance, cleaning or periodic check
up. During the period specified above, ADJ Products, LLC will replace defective parts at its expense
with new or refurbished parts, and will absorb all expenses for warranty service and repair labor by
reason of defects in material or workmanship. The sole responsibility of ADJ Products, LLC under this
warranty shall be limited to the repair of the product, or replacement thereof, including parts, at the sole
discretion of ADJ Products, LLC. All products covered by this warranty were manufactured after August
15, 2012, and bear indentifying marks to that effect.

E. ADJ Products, LLC reserves the right to make changes in design and/or improvements upon its products
without any obligation to include these changes in any products theretofore manufactured.

No warranty, whether expressed or implied, is given or made with respect to any accessory supplied with
products described above. Except to the extent prohibited by applicable law, all implied warranties made
by ADJ Products, LLC in connection with this product, including warranties of merchantability or fitness,
are limited in duration to the warranty period set forth above. And no warranties, whether expressed or
implied, including warranties of merchantability or fitness, shall apply to this product after said period
has expired. The consumer’s and/or Dealer’s sole remedy shall be such repair or replacement as is
expressly provided above; and under no circumstances shall ADJ Products, LLC be liable for any loss or
damage, direct or consequential, arising out of the use of, or inability to use, this product.

This warranty is the only written warranty applicable to ADJ Products, LLC Products and
supersedes all prior warranties and written descriptions of warranty terms and conditions heretofore
published.

MANUFACTURER’S LIMITED WARRANTY PERIODS:

 •LightingProducts=1-year(365days)LimitedWarranty(Such as: Special Effect Lighting, Intelligent

Lighting, UV lighting, Strobes, Fog Machines, Bubble Machines, Mirror Balls, Par Cans, Trussing,
Lighting Stands etc. excluding LED and lamps)

 •LaserProducts=1Year(365Days)LimitedWarranty(excluding laser diodes which have a 6 month

limited warranty)

 •L.E.D.Products=2-year(730days)LimitedWarranty(excluding motors, PCB boards, and power
supplies, which have a 1-year (365 day Limited Warranty) batteries which have a 180 day limited war-

ranty). Only the L.E.D.s carry a 2-year warranty (excluding StarTec Series which a carries a 90 Day

Limited Warranty)

•ADJDMXControllers=2Year(730Days)LimitedWarranty(excluding faders and tact switches)

ADJ Products, LLC - www.adj.com - UV Flood 36 Instruction Manual Page 14

UV Flood 36 Specifications

Model:

UV Flood 36

Working Position: Any safe working position
Voltage: 100V ~ 240V, 50/60Hz
LEDs: 12 x 3W UV LEDs
Wavelength: 395-400nm
Power Draw: 35W
Power Cord Daisy Chain: 26 Fixtures Max. (120V)
57 Fixtures Max. (230V)
Beam Angle: 57 Degrees
Fuse: 1Amp
Weight: 5lbs./ 2.2Kgs.
Dimensions: 11.75” (L) x 9.25” (W) x 4.5” (H)
300 x 235 x 115mm
Colors: UV
DMX Channels: 3 DMX Channel Modes: 1 Channel
Mode, 2 Channel Mode, & 3
Channel Mode
Warranty: 2 Year (730 days)

Auto Sensing Voltage: This xture contains a electronic volt-

age switch, which will auto sense the voltage when it is plugged
into the power source.

Please Note: Specications and improvements in the design of
this unit and this manual are subject to change without any prior
written notice.

ADJ Products, LLC

6122 S. Eastern Ave. Los Angeles, CA 90040 USA

Tel: [phone] / Fax: [phone]

Web: www.adj.com / E-mail: [e-mail]

A.D.J. Supply Europe B.V.

Junostraat 2

6468 EW Kerkrade

The Netherlands

[e-mail] / www.adj.com

Tel: [phone] / Fax: [phone]