Adj UB 9H User Manual [ru]

UB 9H
©2017 ADJ Products, LLC all rights reserved. Information,
specications, diagrams, images, and instructions herein are subject to change without notice. ADJ Products, LLC logo and identifying product names and numbers herein are trademarks of ADJ Products, LLC. Copyright protection claimed includes all forms and matters of copyrightable materials and information now allowed by statutory or judicial law or hereinafter granted. Product names used in this document may be trademarks or registered trademarks of their respective companies and are hereby acknowledged. All non-ADJ Products, LLC brands and product names are trademarks or registered trademarks of their
respective companies.
ADJ Products, LLC and all aliated companies hereby dis­claim any and all liabilities for property, equipment, building, and electrical damages, injuries to any persons, and direct or indi­rect economic loss associated with the use or reliance of any information contained within this document, and/or as a result of the improper, unsafe, unsucient and negligent assembly, installation, rigging, and operation of this product.
8/17
User Instructions
DOCUMENT VERSION
Please check www.adj.com for the latest revision/update of this guide.
Date
08/04/17
Europe Energy Saving Notice Energy Saving Matters (EuP 2009/125/EC) Saving electric energy is a key to help protecting the enviroment. Please turn o all electrical products when they are not in use. To avoid power consumption in idle mode, disconnect all electrical equipment from power when not in use. Thank you!
Document
Version
1 1.01
Software
Version
DMX
Channel
>
Mode
6/10/12/18 Initial Release
Notes
UB 9H Introduction
UB 9H Features
Unpacking: Thank you for purchasing the UB 9H by ADJ Products, LLC. Every UB 9H has been thoroughly tested and has been shipped in perfect operating condition. Carefully check the shipping carton for damage that may have occurred during shipping. If the carton appears to be damaged, carefully inspect your xture for any damage and be sure all accessories necessary to operate the unit has arrived intact. In the case damage has been found or parts are missing, please contact our toll free customer support number for further instructions. Do not return this unit to your dealer without rst contacting customer sup-
port.
Introduction: The ADJ UB 9H is a DMX intelligent, LED bar fixture. This xture can be used in a stand alone set up or connected in a Master/ Slave set up. This fixture has six operating modes: Sound Active mode, Auto Run mode, Static Color mode, RGBWA+UV Dimmer mode, Built­In Program mode, and DMX control mode.
Customer Support: ADJ Products, LLC provides a customer support line, to provide set up help and to answer any question should you encounter problems during your set up or initial operation. You may also visit us on the web at www.adj.com for any comments or sugges­tions. Service Hours are Monday through Friday 8:00 a.m. to 4:30 p.m. Pacic Standard Time. Voice: (800) 322-6337 Fax: (323) 582-2941 E-mail: support@adj.com
Warning! To prevent or reduce the risk of electrical shock or re, do
not expose this unit to rain or moisture.
• Multi-Colors
• Six Operating Modes
• Electronic Dimming 0-100%
• Built in Microphone
• DMX-512 protocol
• 3-Pin DMX Connection
• 4 DMX Modes: 6 Channel Mode, 10 Channel Mode, 12 Channel Mode, & 18 Channel Mode.
• Magnetic Quick Align (See page 24)
• ADJ UC IR compatible and Airstream IR compatible
• Multiple Unit Power Linking (See page 13)
UB 9H Warranty Registration
The UB 9H carries a 2 year limited warranty. Please fill out the enclosed warranty card to validate your purchase. All returned service items whether under warranty or not, must be freight pre-paid and accompany a return authorization (R.A.) number. The R.A. number must be clearly written on the outside of the return package. A brief description of the problem as well as the R.A. number must also be written down on a piece of paper included in the shipping carton. If the unit is under warranty, you must provide a copy of your proof of purchase invoice. You may obtain a R.A. number by contacting our customer support team on our customer support number. All pack­ages returned to the service department not displaying a R.A. number on the outside of the package will be returned to the shipper.
Caution! There are no user serviceable parts inside this unit. Do not
attempt any repairs yourself, doing so will void your manufactures war­ranty. In the unlikely event your unit may require service please contact ADJ Products, LLC.
PLEASE recycle the shipping carton when ever possible.
UB 9H Installation
The unit should be mounted using a mounting clamp (not provided), axing it to the mounting bracket that is provided with the unit. Always ensure that the unit is rmly xed to avoid vibration and slip­ping while operating. Always ensure that the structure to which you are attaching the unit is secure and is able to support a weight of 10 times the unit’s weight. Also, always use a safety cable that can hold 12 times the weight of the unit when installing the xture. The equipment must be installed by a professional, and it must be installed in a place where it is out of the reach of people’s grasp.
ADJ Products, LLC - www.adj.com - UB 9H User Manual Page 3ADJ Products, LLC - www.adj.com - UB 9H User Manual Page 2
UB 9H Safety Precautions
• To reduce the risk of electrical shock or re, do not expose this unit rain or moisture
• Do not spill water or other liquids into or on to your unit.
• Do not attempt to operate this unit if the power cord has been frayed or broken. Do not attempt to remove or break o the ground prong from the electrical cord. This prong is used to reduce the risk of electrical shock and re in case of an internal short.
• Disconnect from main power before making any type of connection.
• Do not remove the cover under any conditions. There are no user serviceable parts inside.
• Never operate this unit when it’s cover is removed.
• Never plug this unit in to a dimmer pack
• Always be sure to mount this unit in an area that will allow proper ventilation. Allow about 6” (15cm) between this device and a wall.
• Do not attempt to operate this unit, if it becomes damaged.
• This unit is intended for indoor use only, use of this product out` doors voids all warranties.
• During long periods of non-use, disconnect the unit’s main power.
• Always mount this unit in safe and stable matter.
• Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to the point they exit from the unit.
• Cleaning -The fixture should be cleaned only as recommended by t he manufacturer. See page 25 for cleaning details.
• Heat -The appliance should be situated away from heat sources such as radiators, heat registers, stoves, or other appliances (inclu­ d ing amplifiers) that produce heat.
• The fixture should be serviced by qualified service personnel when: A. The power-supply cord or the plug has been damaged. B. Objects have fallen, or liquid has been spilled into the fixture. C. The fixture has been exposed to rain or water. D. The fixture does not appear to operate normally or exhibits a marked change in performance.
UB 9H Safety Precautions
RISK GROUP 3 - RISK OF EXPOSURE TO ULTRAVIOLET (UV) RADIATION!
FIXTURE EMITS HIGH INTENSITY ULTRAVIOLET (UV) LIGHT AT A WAVELENGTH OF 390NM - 410NM.
WEAR PROPER EYE AND SKIN PROTECTION.
AVOID PROLONGED PERIODS OF EXPOSURE.
AVOID WEARING WHITE COLOR CLOTHING AND/OR USING (UV) PAINTS ON SKIN.
AVOID DIRECT EYE AND/OR SKIN EXPOSURE AT DISTANCES SHORTER THAN 11 feet (3.3m).
DO NOT OPERATE FIXTURE WITH DAMAGED OR MISSING EXTERNAL COVER PROTECTIVE LENS.
DO NOT LOOK DIRECTLY INTO THE (UV) LIGHT AND/OR VIEW (UV) LIGHT DIRECTLY WITH OPTICAL INSTRUMENTS THAT MAY CONCEN­TRATE THE LIGHT/RADIATION OUTPUT.
INDIVIDUALS SUFFERING FROM A RANGE OF EYE CONDITIONS, SUN­LIGHT EXPOSURE DISORDERS, OR INDIVIDUALS USING PHOTOSEN­SITIVE MEDICATION, MAY RECEIVE DISCOMFORT IF EXPOSED TO THE ULTRAVIOLET (UV) LIGHT EMITTED FROM THIS FIXTURE.
ADJ Products, LLC - www.adj.com - UB 9H User Manual Page 4 ADJ Products, LLC - www.adj.com - UB 9H User Manual Page 5
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
DMX512
DMX+,DMX-,COMMON
1
2
3
Termination reduces signal errors and avoids signal transmission problems and interference. It is always advisable to connect a DMX terminal, (Resistance 120 Ohm 1/4 W) between PIN 2 (DMX-) and PIN 3 (DMX +) of the last fixture.
POWER
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
UB 9H DMX Set Up
UB 9H DMX Set Up
Power Supply: The ADJ UB 9H contains a automatic voltage switch,
which will auto sense the voltage when it is plugged into the power source. With this switch there is no need to worry about the correct power voltage, this unit can be plugged in anywhere.
DMX-512: DMX is short for Digital Multiplex. This is a universal pro-
tocol used as a form of communication between intelligent fixtures and controllers. A DMX controller sends DMX data instructions from the controller to the fixture. DMX data is sent as serial data that trav­els from fixture to fixture via the DATA “IN” and DATA “OUT” XLR ter­minals located on all DMX fixtures (most controllers only have a DATA “OUT” terminal).
DMX Linking: DMX is a language allowing all makes and models of dierent manufactures to be linked together and operate from a single controller, as long as all xtures and the controller are DMX compli­ant. To ensure proper DMX data transmission, when using several DMX fixtures try to use the shortest cable path possible. The order in which fixtures are connected in a DMX line does not influence the DMX addressing. For example; a fixture assigned a DMX address of 1 may be placed anywhere in a DMX line, at the beginning, at the end, or anywhere in the middle. When a fixture is assigned a DMX address of 1, the DMX controller knows to send DATA assigned to address 1 to that unit, no matter where it is located in the DMX chain.
Data Cable (DMX Cable) Requirements (For DMX Operation):
The UB 9H can be controlled via DMX-512 protocol. The UB 9H has 4 DMX channel modes, please see page 10 for the dierent modes. The DMX address is set on the back panel of the UB 9H. Your unit and your DMX controller require a standard 3-pin XLR con­nector for data input and data output (Figure 1). We recommend Accu-Cable DMX cables. If you are making your own cables, be sure to use standard 110-120 Ohm shielded cable (This cable may be purchased at almost all pro lighting stores). Your cables should be made with a male and female XLR connector on either end of the cable. Also remember that DMX cable must be daisy chained and cannot be split.
ADJ Products, LLC - www.adj.com - UB 9H User Manual Page 6
Figure 1
Notice: Be sure to follow gures two and three when making your own
cables. Do not use the ground lug on the XLR connector. Do not con­nect the cable’s shield conductor to the ground lug or allow the shield conductor to come in contact with the XLR’s outer casing. Grounding the shield could cause a short circuit and erratic behavior.
COMMON
1
DMX512 IN
3
3-PIN XLR
2
Figure 2
XLR Pin Conguration
1 Ground
3 Hot
Pin 1 = Ground
Pin 2 = Data Compliment (negative)
Pin 3 = Data True (positive)
When longer runs of cable are
Figure 4
Pin 1
Pin 2
Pin 3
Do Not Use
Do Not Use
XLR Male Socket
1 Ground
DMX512 OT
3-PIN XLR
2 Cold
3 Hot
1
3
2
DMX +
DMX -
XLR Female Socket
2 Cold
Figure 3
Special Note: Line Termination.
used, you may need to use a terminator on the last unit to avoid erratic behavior. A terminator is a 110-120 ohm 1/4 watt resistor which is con­nected between pins 2 and 3 of a male XLR connector (DATA + and DATA -). This unit is inserted in the female XLR connector of the last unit in your daisy chain to terminate the line. Using a cable terminator (ADJ part number Z-DMX/T) will decrease the possibilities of erratic behavior.
5-Pin XLR DMX Connectors.
512 data cables for DATA transmission in place of 3-pin. 5-pin DMX xtures may be implemented in a 3-pin DMX line. When inserting stan­dard 5-pin data cables in to a 3-pin line a cable adaptor must be used, these adaptors are readily available at most electric stores. The chart below details a proper cable conversion.
Conductor 5-Pin XLR Male (In)3-Pin XLR Female (Out)
Ground/Shield
Data Compliment (- signal)
Data True (+ signal)
Not Used
Not Used
ADJ Products, LLC - www.adj.com - UB 9H User Manual Page 7
Termination reduces signal errors and
1
avoids signal transmission problems
3
and interference. It is always advisable
2
to connect a DMX terminal, (Resistance 120 Ohm 1/4 W) between PIN 2 (DMX-) and PIN 3 (DMX +) of the last fixture.
Some manufactures use 5-pin DMX-
3-Pin XLR to 5-Pin XLR Conversion
Pin 1
Pin 2
Pin 3
UB 9H Operating Instructions
UB 9H Operating Instructions
LED Display On/Off:
To set the LED display to turn off after 10 seconds, press the MODE but­ton until “don” is displayed, press the UP button to display “doff”. Now the display will disappear after 10s. Press any button to turn the display on again. Be advised though that the display will turn off automatically after 10 seconds.
LED Display Inversion:
Follow these instructions to flip the display 180° so that the display can be read upside down.
1. Plug the fixture in and press the MODE button until “dXX” is dis- played. “XX” represents either “on” or “oFF”.
2. Press the SET UP button until “Stnd” is displayed.
3. Press the UP or DOWN buttons to “flip” the display 180°.
Operating Modes:
The UB 9H has six operating modes:
• Static Color Mode - There are 63 colors to choose from.
• RGBWA+UV Dimmer Mode - Choose one of the 6 colors to remain static or adjust the intensity of each color to make your desired
color.
• Built-In Program - There are 22 built-in programs to choose from with multiple adjustments.
• Auto Run - A auto program will run with adjustable fade speed and strobe.
• Sound-Active mode - The unit will react to sound, chasing through the built in programs.
• DMX control mode - This function will allow you to control each individual fixtures traits with a standard DMX 512 controller.
Static Color Mode:
1. Plug the fixture in and press the MODE button until “CLXX” is
displayed.
2. There are 63 colors to choose from. Select your desired color by pressing the UP and DOWN buttons. After you have selected your desired color you can activate strobing by pressing the SET UP button to enter the Flash (strobe) mode.
3. “FS.XX” will now be displayed, this is Flash mode. The Flash can be adjusted between “FS.00” (flash off) to “FS.15” (fastest flash).
RGBWA & UV Dimmer Mode:
1. Plug the fixture in and press the MODE button until “r.XXX” is displayed. You are in Red dimming mode.
2. Press the UP and DOWN buttons to adjust intensity. After you have finished adjusting the intensity, or if you would like to skip to the next color, press the SET UP button.
3. When “G.XXX” is displayed you are in Green dimming mode. Press the UP and DOWN buttons to adjust intensity.
4. When “b.XXX” is displayed you are in Blue dimming mode. Press the UP and DOWN buttons to adjust intensity.
5. When “U.XXX” is displayed you are in White dimming mode. Press the UP and DOWN buttons to adjust intensity.
6. When “A.XXX” is displayed you are in Amber dimming mode. Press the UP and DOWN buttons to adjust intensity.
7. When “u.XXX” is displayed you are in UV dimming mode. Press the UP and DOWN buttons to adjust intensity.
8. After you have adjusted the colors to make your desired color you can then activate strobing by pressing the SET UP button to enter the strobe mode.
9. “FSXX” will be displayed, this is strobe mode. The strobe can be adjusted between “00” (flash off) to “15” (fastest flash).
Auto Run Mode:
In this mode the UB 9H will run a auto program.
1. Plug the fixture in and press the MODE button until “AUTO” is dis-
played.
2. After you have activated Auto Run mode, press the SET UP but­ ton to adjust the fade time.
3. Once you press SET UP “Fd.XX” should be displayed. Use the UP or DOWN buttons to set the fade speed to either “Fd.00” (fade off) or between “Fd.01” (fastest speed) and “Fd.99” (slowest speed). After adjusting the fade speed, press SET UP if you wish to activate the Flash mode.
4. “FS.XX” will now be displayed, this is Flash mode. The Flash can be adjusted between “FS.00” (flash off) to “FS.15” (fastest flash).
ADJ Products, LLC - www.adj.com - UB 9H User Manual Page 8
ADJ Products, LLC - www.adj.com - UB 9H User Manual Page 9
UB 9H Operating Instructions
UB 9H Operating Instructions
Built-In Program Mode:
1. Plug the fixture in and press the MODE button until “Pr.XX” is dis­ played. “XX” represents a number from 1-22. Use the UP or DOWN buttons to scroll through the 22 programs. Programs 21 and 22 have adjustable base and scrolling colors. Once you have found your desired program press the SET UP button.
2. Pressing the SET UP button will display “SP.XX”. When this is dis­ played you can adjust the running speed of your desired program. Use the UP or DOWN button to adjust the speed between “SP.01” (slowest) and “SP.99” (fastest). Once you have set your desired run­ ning speed, you can press the SET UP button to to enter the Fade adjustment mode.
3. Pressing the SET UP button will display “Fd.XX”. When this is dis­ played you can adjust the fade speed of your desired program. Use the UP or DOWN button to adjust the speed between “Fd.01” (fastest) and “Fd.99” (slowest) or “Fd.00” (Off). Once you have set your desired fade speed, you can press the SET UP button to to enter the Flash (Strobe) mode.
4. After pressing SET UP, “FS.XX” will be displayed, this is Flash mode. The Flash can be adjusted between “FS.00” (flash off) to “FS.15” (fastest flash).
• PROGRAMS 21 & 22 - If you have chosen programs 21 or 22, after the Flash mode, press the SET UP button. “C1.XX” will be displayed. This is the base color, use the UP and DOWN buttons to scroll through the 7 colors. Once you have chosen your base color, press the SET UP button again so that “C2.XX” is displayed. This is the moving color, use the UP and DOWN buttons to scroll through the 7
colors.
DMX Mode:
Operating through a DMX controller gives the user the freedom to create their own programs tailored to their own individual needs. This function also allows you to use your fixtures as spot lights. The UB 9H
has 4 DMX modes: 6 Channel mode, 10 Channel mode, 12 Channel mode, and 18 Channel mode. See pages 15-20 for each mode’s DMX
traits.
1. This function will allow you to control each individual fixture’s traits with a standard DMX 512 controller.
2. To run your fixture in DMX mode press the MODE button until
“d.XXX” is displayed. “XXX” represents the current displayed ad­ dress. Use the UP or DOWN buttons to select your desired DMX address, then press the SETUP button so that “Ch.XX” is displayed.
3. Use the UP or DOWN buttons to scroll through the DMX Channel modes. The Channel modes are listed below:
• To run the 6 Channel Mode, press the MODE button until “Ch06” is displayed. This is the 6 Channel DMX Mode.
• To run the 10 Channel Mode, press the MODE button until “Ch10” is displayed. This is the 10 Channel DMX Mode.
• To run the 12 Channel Mode, press the MODE button until “Ch12” is displayed. This is the 12 Channel DMX Mode.
• To run the 18 Channel Mode, press the MODE button until “Ch18” is displayed. This is the 18 Channel DMX Mode.
4. Please see pages 15-20 for DMX values and traits.
5. After you have chosen your desired DMX Channel mode plug in the fixture via the XLR connections to any standard DMX control-
ler.
Sound Active Mode:
1. Plug the fixture in and press the MODE button until “SU.XX” is displayed. “XX” represents the sound sensitivity level.
2. Use the UP or DOWN buttons to adjust the sound sensitivity. “SU.00” is off, “SU.01 is the lowest sensitivity, and “SU.31” is the highest. After adjusting the sound sensitivity, press SET UP if you wish to activate the Flash mode.
3. “FS.XX” will now be displayed, this is Flash mode. The Flash can be adjusted between “FS.00” (flash off) to “FS.15” (fastest flash).
ADJ Products, LLC - www.adj.com - UB 9H User Manual Page 10
ADJ Remote Activation:
This function is used to activate and deactivate the IR sensor. When this function is activated you can control the fixture using either the ADJ UC IR or Airstream App. Please see page 14 for the controls and functions.
1. Plug the fixture in and press the MODE button until “dXX” is dis­ played. “XX” represents either “on” or “oFF”.
2. Press the SET UP button until “IrXX” is displayed. “XX” represents either “on” or “oF”.
3. Press the UP or DOWN buttons to either activate the remote func­ tion (On) or deactivate it (Off).
ADJ Products, LLC - www.adj.com - UB 9H User Manual Page 11
UB 9H Operating Instructions
UB 9H Operating Instructions
DMX State:
This mode can be used as a precaution mode, that in case the DMX signal is lost, the operating mode chosen in the setup is the running mode the xture will go into when the DMX signal is lost. You can also set this as the operating mode you would like the unit to return to when power is applied.
1. Plug the fixture in and press the MODE button until “d.XXX” is dis- played. “XXX” represents the current displayed DMX address.
2. Press the SET UP button so that “nodn” is displayed. Use the UP and DOWN buttons to scroll through the DMX states.
• “bLAC” (Blackout) - If the DMX signal is lost or interrupted, the unit will automatically go into stand by mode.
• “LASt” (Last State) - If the DMX signal is lost or interrupted, the xture will stay in the last DMX set up. If power is applied and this mode is set, the unit will automatically go into the last DMX set up.
• “ProG” (Auto Run) - If the DMX signal is lost or interrupted, the unit will automatically go into Auto Run mode.
3. Use the UP and DOWN buttons to nd your desired DMX state and press SET UP to conrm and exit.
Dimmer Curve:
This is used to set the dimming curve used with DMX mode. See page 22 for the different dimming curves.
1. Plug the fixture in and press the MODE button until the current DMX address is displayed.
2. Press the SET UP button until “dr-X” is displayed. “X” represents the displayed dimmer curve (0-4).
• 0 - Standard
• 1 - Stage
• 2 - TV
• 3 - Architectural
• 4 - Theatre
3. Press the UP or DOWN buttons to scroll through and select your desired dimming curve.
Default Running Mode:
This is a default running mode. When this mode is activated all modes will return to their default settings and a Auto program will run.
1. Plug the fixture in and press the MODE button until “dXX” is dis­ played. “XX” represents either “on” or “oFF”.
2. Press the SET UP button until “dEFA” is displayed.
3. Press the UP and DOWN buttons at the same time.
UB 9H Master-Slave Configuration
Master-Slave Configuration:
This function will allows you to link units together to run in a Master-Slave mode. In Master-Slave operation one unit will act as the controlling unit
and the others will react to the controlling units built-in programs. Any unit can act as a Master or as a Slave however, only one unit can be pro­grammed to act as the “Master.”
Master-Slave Connections and Settings:
1. Daisy chain your units via the XLR connector on the rear of the unit. Use standard XLR data cables to link your units together. Remember that the Male XLR connector is the input and the Female XLR con- nector is the ouput. The first unit in the chain (master) will use the female XLR connector only. The last unit in the chain will use the male XLR connector only.
2. Set the “Master” unit to your desired operating mode and then
connect the “Slave” unit or units.
3. For the “Slave” unit(s) press the MODE button until “SLAu” is dis­ played. The “Slave” unit(s) will now follow the “Master” unit.
UB 9H Multiple Unit Power Linking
With this feature you can connect the xtures to one another using the IEC input and output sockets. The maximum that can be connected is 10 xtures @ 120V and 18 xtures @ 240V. After the maximum connected fixtures you will need to use a new
power outlet. NOTE: USE CAUTION WHEN POWER LINKING OTHER FIXTURES TO THE UB 9H AS THE POWER CONSUMPTION OF OTHER LIGHTING FIXTURES WILL VARY!
ADJ Products, LLC - www.adj.com - UB 9H User Manual Page 12 ADJ Products, LLC - www.adj.com - UB 9H User Manual Page 13
UB 9H ADJ UC IR/Airstream IR Operation
The UC IR infrared remote gives you control of various functions (See below). To control the fixture you must aim the remote at the front of the fix­ture and be no more than 30 feet away. To use the ADJ UC IR you must first activate the fixtures infrared sensor, to activate the sensor please see the instructions on page 11.
The Airstream IR remote transmitter plugs into the headphone jack of your iOS phone or tablet. To control your IR fixture you must raise the volume to the maximum on your iOS phone or tablet and aim the transmitter at the fix­ture sensor and be no more than 15 feet away. After you have purchased the Airstream IR transmitters, the app is a free download from the app store for your iOS phone or tablet. The app comes with 3 pages of control depending on the fixture you are using. Please see below for IR functions including the
corresponding app page.
Works with App page 1.
STAND BY - Pressing this button will blackout the fixture. Press the button
again to return to the initial state.
FULL ON - Press this button down to fully light up the unit. Press this button again to return the unit to its last mode of operation.
FADE/GOBO - This button activates fade mode. Use buttons 1-3 to adjust the fade speed.
UB 9H 6 Channel Mode
Channel Value Function
1 RED
0 - 255 0% - 100% 2 GREEN 0 - 255 0% - 100% 3 BLUE 0 - 255 0% - 100% 4 WHITE 0 - 255 0% - 100% 5 AMBER 0 - 255 0% - 100% 6 UV 0 - 255 0% - 100%
“DIMMER +” and “DIMMER -” - Use these buttons to adjust the output in-
tensity.
STROBE - Press this button to activate strobing. Use buttons 1-4 to adjust the strobe speed. “1” being the slowest, “4” being the fastest. Press this button again to stop strobing.
COLOR - Press this button to activate color mode. Use buttons 1-9 to find your desired color.
1-9 - Use buttons 1-9 to select your desired color when color mode is active or your desired program when show mode is active. Use buttons 1-4 to se­lect you desired strobe rate when strobing is active.
SOUND ON & OFF - Use the buttons to activate and deactivate sound ac-
tive mode.
SHOW 0 - Press this button to activate show mode. Use buttons 1-9 to
select your desired show. Press this button twice for show 10. Press button 1 twice for show 11.
ADJ Products, LLC - www.adj.com - UB 9H User Manual Page 14 ADJ Products, LLC - www.adj.com - UB 9H User Manual Page 15
UB 9H 10 Channel Mode
Channel Value Function
UB 9H 12 Channel Mode
Channel Value Function
1 RED
0 - 255 0% - 100% 2 GREEN 0 - 255 0% - 100% 3 BLUE 0 - 255 0% - 100% 4 WHITE 0 - 255 0% - 100% 5 AMBER 0 - 255 0% - 100% 6 UV 0 - 255 0% - 100% 7 0 - 255 COLOR MACROS (See the Color Macro Chart on page 21) 8 STROBING 0 - 31 LED OFF 32 - 63 LED ON 64 - 95 STROBING SLOW - FAST 96 - 127 LED ON 128 - 159 PULSE STROBING SLOW - FAST 160 - 191 LED ON 192 - 223 RANDOM STROBING SLOW - FAST 224 - 255 LED ON 9 MASTER DIMMER 0 - 255 0% - 100% 10 DIMMER CURVES 0 - 20 STANDARD 21 - 40 STAGE 41 - 60 TV 61 - 80 ARCHITECTURAL 81 - 100 THEATRE 101 - 255 DEFAULT TO UNIT SETTING
1 RED 0 - 255 0% - 100% 2 GREEN 0 - 255 0% - 100% 3 BLUE 0 - 255 0% - 100% 4 WHITE 0 - 255 0% - 100% 5 AMBER 0 - 255 0% - 100% 6 UV 0 - 255 0% - 100% 7 0 - 255 COLOR MACROS (See the Color Macro Chart on page 21)
12 Channel Mode DMX Traits continued on the next page.
ADJ Products, LLC - www.adj.com - UB 9H User Manual Page 16 ADJ Products, LLC - www.adj.com - UB 9H User Manual Page 17
UB 9H 12 Channel Mode Cont.
Channel Value Function
UB 9H 12 Channel Mode Cont.
Channel Value Function
8 PROGRAMS 0 - 15 NO FUNCTION 16 - 25 PROGRAM 1 26 - 35 PROGRAM 2 36 - 45 PROGRAM 3 46 - 55 PROGRAM 4 56 - 65 PROGRAM 5 66 - 75 PROGRAM 6 76 - 85 PROGRAM 7 86 - 95 PROGRAM 8 96 - 105 PROGRAM 9 106 - 115 PROGRAM 10 116 - 125 PROGRAM 11 126 - 135 PROGRAM 12 136 - 145 PROGRAM 13 146 - 155 PROGRAM 14 156 - 165 PROGRAM 15 166 - 175 PROGRAM 16 176 - 185 PROGRAM 17 186 - 195 PROGRAM 18 196 - 205 PROGRAM 19 206 - 215 PROGRAM 20 216 - 225 PROGRAM 21 226 - 235 PROGRAM 22 236 - 245 AUTO RUN 246 - 255 SOUND ACTIVE 9 0 - 255 PROGRAM SPEED/SOUND SENSE
10 STROBING 0 - 31 LED OFF 32 - 63 LED ON 64 - 95 STROBING SLOW - FAST 96 - 127 LED ON 128 - 159 PULSE STROBING SLOW - FAST 160 - 191 LED ON 192 - 223 RANDOM STROBING SLOW - FAST 224 - 255 LED ON 11 MASTER DIMMER 0 - 255 0% - 100% 12 DIMMER CURVES 0 - 20 STANDARD 21 - 40 STAGE 41 - 60 TV 61 - 80 ARCHITECTURAL 81 - 100 THEATRE 101 - 255 DEFAULT TO UNIT SETTING
Section Mode
Section 1 Section 2 Section 3
Section Mode refers to 18 Channel Mode.
ADJ Products, LLC - www.adj.com - UB 9H User Manual Page 18 ADJ Products, LLC - www.adj.com - UB 9H User Manual Page 19
UB 9H 18 Channel Mode
Channel Value Function
1 RED SECTION 1
0 - 255 0% - 100% 2 GREEN SECTION 1 0 - 255 0% - 100% 3 BLUE SECTION 1 0 - 255 0% - 100% 4 WHITE SECTION 1 0 - 255 0% - 100% 5 AMBER SECTION 1 0 - 255 0% - 100% 6 UV SECTION 1 0 - 255 0% - 100% 7 RED SECTION 2 0 - 255 0% - 100% 8 GREEN SECTION 2 0 - 255 0% - 100% 9 BLUE SECTION 2 0 - 255 0% - 100% 10 WHITE SECTION 2 0 - 255 0% - 100% 11 AMBER SECTION 2 0 - 255 0% - 100% 12 UV SECTION 2 0 - 255 0% - 100% 13 RED SECTION 3 0 - 255 0% - 100% 14 GREEN SECTION 3 0 - 255 0% - 100% 15 BLUE SECTION 3 0 - 255 0% - 100% 16 WHITE SECTION 3 0 - 255 0% - 100% 17 AMBER SECTION 3 0 - 255 0% - 100% 18 UV SECTION 3
0 - 255 0% - 100%
ADJ Products, LLC - www.adj.com - UB 9H User Manual Page 20 ADJ Products, LLC - www.adj.com - UB 9H User Manual Page 21
UB 9H Color Macro Chart
=G+B 112-115=R+B+UV 176-179=R+G+B+UV 240-243=R+G+W+A+UV
0-3=Off 64-67=B+W 128-131=G+B+W 192-195=R+B+W+A
4-7=Red 68-71=B+A 132-135=G+B+A 196-199=R+B+W+UV
8-11=Green 72-75=B+UV 136-139=G+B+UV 200-203=R+B+A+UV
12-15=Blue 76-79=W+A 140-143=G+W+A 204-207=R+W+A+UV
20-23=Amber 84-87=A+UV 148-151=G+A+UV 212-215=G+B+W+UV
24-27=UV 88-91=R+G+B 152-155=B+W+A 216-219=G+B+A+UV
16-19=White 80-83=W+UV 144-147=G+W+UV 208-211=G+B+W+A
28-31=R+G 92-95=R+G+W 156-159=B+W+UV 220-223=G+W+A+UV
32-35=R+B 96-99=R+G+A 160-163=B+A+UV 224-227=B+W+A+UV
36-39=R+W 100-103=R+G+UV 164-167=W+A+UV 228-231=R+G+B+W+A
40-43=R+A 104-107=R+B+W 168-171=R+G+B+W 232-235=R+G+B+W+UV
44-47=R+UV 108-111=R+B+A 172-175=R+G+B+A 236-239=R+G+B+A+UV
48-51
52-55=G+W 116-119=R+W+A 180-183=R+G+W+A 244-247=R+B+W+A=UV
56-59=G+A 120-123=R+W+UV 184-187=R+G+W+UV 248-251=G+B+W+A+UV
60-63=G+UV 124-127=R+A+UV 188-191=R+G+A+UV 252-255=R+G+B+W+A+UV
39.64”/1007mm
41.37”/1051mm
DIMMER
UB 9H Dimming Curves
100%
50%
10%
0%
Rise Time Down Time
0 Sec
0 sec Fade Time 1 sec Fade Time
Dimming Curve
Ramp Effect
0 0
Standard (default) 0 0 0 0 Stage 780 1100 1540 1660 TV 1180 1520 1860 1940 Architectural 1380 1730 2040 2120 Theatre 1580 1940 2230 2280
Rise Time (ms) Down Time (ms) Rise Time (ms) Down Time (ms)
255 255
Time (ms)
UB 9H Dimensional Drawings
1.91”/74mm
3.57”/90.78mm
41.61”/1056.93mm
41.37”/1051mm
39.64”/1007mm
2.67”/68mm
2.36”/60mm
2.55”/65mm
1.91”/74mm
3.57”/90.78mm
ADJ Products, LLC - www.adj.com - UB 9H User Manual Page 22 ADJ Products, LLC - www.adj.com - UB 9H User Manual Page 23
UB 9H Magnetic Quick Align
UB 9H Fuse Replacement
This unit features a magnetic quick align feature which allows you to connect multiple xtures securely end-to-end. This feature is exclusively used for when the xtures are used on a at surface such as a oor or stage for uplighting. To use this feature, uscrew the thumb screws on both ends of the xture and remove both brackets. Position the xtures on a at surface and connect them end-to-end.
Magnet Side
Remove Bracket
Magnet
Disconnect the unit from its power source. Remove the power cord from the unit. Use a flat head head screwdriver to remove the fuse holder. Remove the fuse located inside the fuse holder and replace with the new fuse. Install the fuse holder and new fuse and secure it.
UB 9H Trouble Shooting
Listed below are a few common problems the user may encounter, with solutions.
Unit not responding to DMX:
1. Check that the DMX cables are connected properly and are wired correctly (pin 3 is “hot”; on some other DMX devices pin 2 may be ‘hot’). Also, check that all cables are connected to the right connectors; it does matter which way the inputs and outputs are connected.
Unit does not respond to sound:
1. Quiet or high pitched sounds will not activate the unit.
2. Make sure that Sound Active mode is activated.
UB 9H Cleaning
Due to fog residue, smoke, and dust cleaning the internal and exter­nal optical lenses must be carried out periodically to optimize light output.
1. Use normal glass cleaner and a soft cloth to wipe down the outside casing.
2. Clean the external optics with glass cleaner and a soft cloth every 20 days.
3. Always be sure to dry all parts completely before plugging the unit back in. Cleaning frequency depends on the environment in which the fixture operates (i.e. smoke, fog residue, dust, dew).
ADJ Products, LLC - www.adj.com - UB 9H User Manual Page 24 ADJ Products, LLC - www.adj.com - UB 9H User Manual Page 25
UB 9H Warranty
MANUFACTURER’S LIMITED WARRANTY
A. ADJ Products, LLC hereby warrants, to the original purchaser, ADJ Products, LLC products to be free of manufacturing defects in material and workmanship for a prescribed period from the date of purchase (see specific warranty period on reverse). This warranty shall be valid only if the product is purchased within the United States of America, including possessions and territories. It is the owner’s responsibility to establish the date and place of purchase by acceptable evidence, at the time service is sought.
B. For warranty service you must obtain a Return Authorization number (RA#) before sending back the product–please contact ADJ Products, LLC Service Department at 800-322-6337. Send the product only to the ADJ Products, LLC factory. All shipping charges must be pre-paid. If the requested repairs or service (including parts replacement) are within the terms of this warranty, ADJ Products, LLC will pay return shipping charges only to a designated point within the United States. If the entire instrument is sent, it must be shipped in it’s original package. No accessories should be shipped with the product. If any accessories are shipped with the product, ADJ Products, LLC shall have no liability whatsoever for loss of or damage to any such accessories, nor for the safe return thereof.
C. This warranty is void if the serial number has been altered or removed; if the product is modified in any manner which ADJ Products, LLC concludes, after inspection, affects the reliability of the product; if the product has been repaired or serviced by anyone other than the ADJ Products, LLC factory unless prior written authorization was issued to purchaser by ADJ Products, LLC; if the product is damaged because not properly maintained as set forth in the instruction manual.
D. This is not a service contract, and this warranty does not include maintnance, cleaning or periodic check up. During the period specified above, ADJ Products, LLC will replace defective parts at its expense with new or refurbished parts, and will absorb all expenses for warranty service and repair labor by reason of defects in material or workmanship. The sole responsibility of ADJ Products, LLC under this warranty shall be limited to the repair of the product, or replacement thereof, including parts, at the sole discretion of ADJ Products, LLC. All products covered by this warranty were manufactured after August 15, 2012, and bear indentifying marks to that effect.
E. ADJ Products, LLC reserves the right to make changes in design and/or improvements upon its products without any obligation to include these changes in any products theretofore manufactured.
No warranty, whether expressed or implied, is given or made with respect to any accessory supplied with products described above. Except to the extent prohibited by applicable law, all implied warranties made by ADJ Products, LLC in connection with this product, including warranties of merchantability or fitness, are limited in duration to the warranty period set forth above. And no warranties, whether expressed or implied, including warranties of merchantability or fitness, shall apply to this product after said period has expired. The consumer’s and/or Dealer’s sole remedy shall be such repair or replacement as is expressly provided above; and under no circumstances shall ADJ Products, LLC be liable for any loss or damage, direct or consequential, arising out of the use of, or inability to use, this product.
This warranty is the only written warranty applicable to ADJ Products, LLC Products and supersedes all prior warranties and written descriptions of warranty terms and conditions heretofore published.
MANUFACTURER’S LIMITED WARRANTY PERIODS:
•NonL.E.D.LightingProducts=1-year(365days)LimitedWarranty(Such as: Special Effect
Lighting, Intelligent Lighting, UV lighting, Strobes, Fog Machines, Bubble Machines, Mirror Balls, Par Cans, Trussing, Lighting Stands etc. excluding LED and lamps)
•LaserProducts=1Year(365Days)LimitedWarranty(excluding laser diodes which have a 6 month
limited warranty)
•L.E.D.Products=2-year(730days)LimitedWarranty(excluding batteries which have a 180 day lim-
ited warranty). Note:2YearWarrantyonlyappliestopurchaseswithintheUnitedStates.
•StarTecSeries=1YearLimitedWarranty(excluding batteries which have a 180 day limited warranty).
•ADJDMXControllers=2Year(730Days)LimitedWarranty
ADJ Products, LLC - www.adj.com - UB 9H User Manual Page 26
UB 9H Specifications
Model:
UB 9H
Voltage: 100V ~ 240V/50~60Hz LEDs: 9 x 6W 6-in-1 HEX LEDs
Beam Angle: 40 Degrees Working Position: Any safe working position Power Draw: 62W Power Linking: 10 Fixtures Max. @ 120V 18 Fixtures Max. @ 240V Fuse: 2 Amp Weight: 6lbs./ 2.6Kgs. Dimensions: 41.75” (L) x 2.5” (W) x 3.5” (H) 1060 x 63 x 90mm Colors: RGBWA+UV Color Mixing DMX Channels: 4 DMX Modes: 6 Channel Mode, 10 Channel Mode, 12 Channel Mode, & 18 Channel Mode Warranty: 2 Year (730 days) Limited Warranty
Please Note: Specications and improvements in the design of this unit and this manual are subject to change without any prior written notice.
ADJ Products, LLC
6122 S. Eastern Ave. Los Angeles, CA 90040 USA
Tel: 323-582-2650 / Fax: 323-725-6100
Web: www.adj.com / E-mail: info@americandj.com
A.D.J. Supply Europe B.V.
Junostraat 2
6468 EW Kerkrade
Netherlands
service@adjgroup.eu / www.adj.com
Tel: +31 45 546 85 00 / Fax: +31 45 546 85 99
Loading...