LED Trispot Introduction
LED TRISPOT
Unpacking: Thank you for purchasing the LED Trispot by Ameri-
can DJ®. Every LED Trispot has been thoroughly tested and has been
shipped in perfect operating condition. Carefully check the shipping
carton for damage that may have occurred during shipping. If the
carton appears to be damaged, carefully inspect your xture for any
damage and be sure all accessories necessary to operate the unit has
arrived intact. In the case damage has been found or parts are missing, please contact our toll free customer support number for further
instructions. Do not return this unit to your dealer without rst contacting customer support.
Introduction: The LED Trispot is part of American DJ’s continuing
pursuit for creating high quality affordable intelligent fixtures. The LED
Trispot is a simple DMX intelligent LED effect. This fixture is light weight
and compact which makes it a great piece for mobile DJ’s and clubs.
This unit can be used as a stand alone, or a sound-active mode. The
unit can also be controlled via DMX controller.
Customer Support: American DJ® provides a toll free customer sup-
port line, to provide set up help and to answer any question should you
encounter problems during your set up or initial operation. You may
also visit us on the web at www.americandj.com for any comments or
suggestions. Service Hours are Monday through Friday 9:00 a.m. to
5:00 p.m. Pacic Standard Time.
Voice: (800) 322-6337
Fax: (323) 582-2941
E-mail: support@americandj.com
To purchase parts online visit http://parts.americandj.com
User Instructions
American DJ®
6122 S. Eastern Ave.
Los Angeles Ca. 90040
10/08
www.americandj.com
Warning! To prevent or reduce the risk of electrical shock or re, do
not expose this unit to rain or moisture.
Caution! There are no user serviceable parts inside this unit. Do not
attempt any repairs yourself, doing so will void your manufactures warranty. In the unlikely event your unit may require service please contact
American DJ®.
PLEASE recycle the shipping carton when ever possible.
©American DJ Supply® - www.americandj.com - LED Trispot Instruction Manual Page 2
LED Trispot General Instructions
LED Trispot Safety Precautions
To optimize the performance of this product, please read these
operating instructions carefully to familiarize yourself with the basic
operations of this unit. These instructions contain important safety
information regarding the use and maintenance of this unit. Please
keep this manual with the unit, for future reference.
LED Trispot Features
• Multi-Colors
• Color Strobe
• Electronic Dimming 0-100%
• Built in Microphone
• DMX-512 protocol
• Uses 3 or 5 DMX Channels
• Daisy Chain Units Together in DMX Mode
LED Trispot Warranty Registration
The LED Trispot carries a 1 year (365 days) limited warranty. Please
fill out the enclosed warranty card to validate your purchase and warranty. You may also register your product online at www. americandj.
com. All returned service items whether under warranty or not, must
be freight pre-paid and accompany a return authorization (R.A.) number. If the unit is under warranty you must provide a copy of your
proof of purchase invoice. Please contact American DJ® customer
support for a R.A. number.
• To reduce the risk of electrical shock or re, do not expose this unit
rain or moisture
• Do not spill water or other liquids into or on to your unit.
• Be sure that the local power outlet match that of the required volt age for your unit.
• Do not attempt to operate this unit if the power cord has been
frayed or broken. Do not attempt to remove or break off the ground
prong from the electrical cord. This prong is used to reduce the risk
of electrical shock and re in case of an internal short.
• Disconnect from main power before making any type of connection.
• Do not remove the cover under any conditions. There are no user
serviceable parts inside.
• Never operate this unit when it’s cover is removed.
• Never plug this unit in to a dimmer pack
• Always be sure to mount this unit in an area that will allow proper
ventilation. Allow about 6” (15cm) between this device and a wall.
• Do not attempt to operate this unit, if it becomes damaged.
• This unit is intended for indoor use only, use of this product out`
doors voids all warranties.
• During long periods of non-use, disconnect the unit’s main power.
• Always mount this unit in safe and stable matter.
• Power-supply cords should be routed so that they are not likely to
be walked on or pinched by items placed upon or against them,
paying particular attention to the point they exit from the unit.
• Cleaning -The fixture should be cleaned only as recommended by
t he manufacturer. See page 10 for cleaning details.
• Heat -The appliance should be situated away from heat sources
such as radiators, heat registers, stoves, or other appliances (inclu d ing amplifiers) that produce heat.
• The fixture should be serviced by qualified service personnel when:
A. The power-supply cord or the plug has been damaged.
B. Objects have fallen, or liquid has been spilled into the appliance.
C. The appliance has been exposed to rain or water.
D. The appliance does not appear to operate normally or exhibits a
marked change in performance.
©American DJ Supply® - www.americandj.com - LED Trispot Instruction Manual Page 4©American DJ Supply® - www.americandj.com - LED Trispot Instruction Manual Page 3
LED Trispot Set Up
DMX512 IN
3-PIN XLR
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
DMX512
DMX+,DMX-,COMMON
1
2
3
Terminatio n re duces signal errors and
avo ids signal tran smis sion problem s
and interference. It is always advisable
to connect a DMX terminal, (Resistance
120 Ohm 1/4 W) between PIN 2 (DMX-)
and PIN 3 (DMX +) of the last fixture.
1
2
3
1
2
3
DMX +
DMX -
COMMON
DMX512 OUT
3-PIN XLR
LED Trispot Set Up
Power Supply: Before plugging your unit in, be sure the source voltage in your area matches the required voltage for your American DJ®
LED Trispot. The American DJ® LED Trispot is a 100v ~ 220v unit.
Because of voltage setup of the unit you do not have to worry about
wall output voltage. This unit is compatiable with all wall outputs.
DMX-512: DMX is short for Digital Multiplex. This is a universal pro-
tocol used as a form of communication between intelligent fixtures
and controllers. A DMX controller sends DMX data instructions from
the controller to the fixture. DMX data is sent as serial data that travels from fixture to fixture via the DATA “IN” and DATA “OUT” XLR terminals located on all DMX fixtures (most controllers only have a DATA
“OUT” terminal).
DMX Linking: DMX is a language allowing all makes and models of
different manufactures to be linked together and operate from a single
controller, as long as all xtures and the controller are DMX compliant. To ensure proper DMX data transmission, when using several
DMX fixtures try to use the shortest cable path possible. The order
in which fixtures are connected in a DMX line does not influence the
DMX addressing. For example; a fixture assigned a DMX address of 1
may be placed anywhere in a DMX line, at the beginning, at the end,
or anywhere in the middle. When a fixture is assigned a DMX address
of 1, the DMX controller knows to send DATA assigned to address 1
to that unit, no matter where it is located in the DMX chain.
Dip-switches in DMX mode: This unit uses dip switches to assign a
DMX address. Each dip switch represents a binary value.
Dip Switch 1 address equals 1
Dip Switch 2 address equals 2
Dip Switch 3 address equals 4
Dip Switch 4 address equals 8
Dip Switch 5 address equals 16
Dip Switch 6 address equals 32
Dip Switch 7 address equals 64
Dip Switch 8 address equals 128
Dip Switch 9 address equals 256
Dipswitch 10 - Some units omit dipswitch 10. When a unit does include dipswitch 10 it is usually used for special functions such as
sound activation.
DMX CHANNEL
ON
1 98765432 10
1282 8 32
Each dip switch has a preset value. A specific DMX address is set by
combining the dip switches that sum your desired value. For example:
To achieve a DMX address of 21, combine dip switches 1, 3, and 5.
Sense dip switch 1 has a value of 1, dip switch 3 has a value of 4, and
dip switch 5 has a value of 16, the combination of the create a DMX
value of 21.
Set DMX address 21: Set DMX address 201:
Dip-switches # 1 = 1 Dip-switches # 1 = 1
3 = 4 4 = 8
5 = 16 7 = 64
= 21 8 = 128
= 201
Data Cable (DMX Cable) Requirements (For DMX Operation):
The LED Trispot can be controlled via DMX-512 protocol. The LED Tri-
spot can be either a three or ve channel DMX unit. The DMX address
is set on the back panel of the LED Trispot. Your unit and your DMX
controller require a standard 3-pin XLR connector
for data input and data output (Figure 1). If you are
making your own cables, be sure to use standard
two conductor shielded cable (This cable may be
purchased at almost all pro sound and lighting
stores). Your cables should be made with a male
and female XLR connector on either end of the
cable. Also remember that DMX cable must be
Figure 1
daisy chained and can not be split.
Notice: Be sure to follow gures two and three when making your own
SF
cables. Do not use the ground lug on the XLR connector. Do not connect the cable’s shield conductor to the ground lug or allow the shield
conductor to come in contact with the XLR’s outer casing. Grounding
the shield could cause a short circuit and erratic behavior.
256651641
Figure 2
©American DJ® - www.americandj.com - LED Trispot Instruction Manual Page 5
©American DJ Supply® - www.americandj.com - LED Trispot Instruction Manual Page 6
XLR Male Socket
POWER
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
1
2
3
Terminatio n re duces signal errors and
avo ids signal tran smis sion problem s
and interference. It is always advisable
to connect a DMX terminal, (Resistance
120 Ohm 1/4 W) between PIN 2 (DMX-)
and PIN 3 (DMX +) of the last fixture.
1 Ground
Figure 3
2 Cold
3 Hot
Special Note: Line Termination.
XLR Female Socket
2 Cold
XLR Pin Conguration
1 Ground
3 Hot
Pin 1 = Ground
Pin 2 = Data Compliment (negative)
Pin 3 = Data True (positive)
When longer runs of cable are
used, you may need to use a terminator on the last unit to avoid erratic
behavior. A terminator is a 90-120 ohm 1/4 watt resistor which is connected between pins 2 and 3 of a male XLR connector (DATA + and
DATA -). This unit is inserted in the female XLR connector of the last
unit in your daisy chain to terminate the line. Using a cable terminator
(ADJ part number Z-DMX/T) will decrease the possibilities of erratic
behavior.
Figure 4
5-Pin XLR DMX Connectors.
Some manufactures use 5-pin XLR
connectors for DATA transmission in place of 3-pin. 5-pin XLR xtures
may be implemented in a 3-pin XLR DMX line. When inserting standard
5-pin XLR connectors in to a 3-pin line a cable adaptor must be used,
these adaptors are readily available at most electric stores. The chart
below details a proper cable conversion.
Data Compliment (- signal)
Data True (+ signal)
Conductor 5-Pin XLR Male (In)3-Pin XLR Female (Out)
Ground/Shield
Not Used
Not Used
3-Pin XLR to 5-Pin XLR Conversion
Pin 1
Pin 2
Pin 3
Pin 1
Pin 2
Pin 3
Do Not Use
Do Not Use
LED Trispot Operating Instructions LED Trispot Set Up
Operating Modes:
Sound Active Mode:
In this mode the LED Trispot will react to sound, and chase through
the different colors.
1. Plug the fixture in and put dipswitch #10 in the “ON” postion.
2. The fixture will now change via sound.
Master/Slave Operation:
This function will allow you to link up to 16 units together and operate
without a controller. The units will be sound activated. In Master-Slave
operation one unit will act as the controlling unit and the others will
react to the controlling units programs. Any unit can act as a Master
or as a Slave.
1. Using approved DMX data cables, daisy chain your units togeth-
er via the XLR connector on the rear of the units. Remember the
Male XLR connector is the input and the Female XLR connector
is the output. The rst unit in the chain (master) will use the female
XLR connector only - The last unit in the chain will use the male
XLR connector only. For longer cable runs we suggest a termina-
tor at the last fixture.
2. On the master unit dipswitches 1-9 must be in the “Off” position.
3. On the slave units set any dipswitch to the “On” position.
4. The slave units will now follow the Master unit.
4-Light Show (Using Master/Slave Operation):
This function will allow you to run a 4-Light Show either from the
Master Unit or from the rst slave unit. Follow step 1 in Master/Slave
Opertation and then follow the instructions below to set up the rest of
the show.
Slave units follow the rst Slave unit:
1. On the Master unit set all dipswitches to the “Off” postion.
2. On the Slave units set any dipswitches to the “On” postion,
except dipswitch 10. Dipswitch 10 must stay in the “Off” postion.
3. Now all connected units except the master will follow the rst
slave unit.
Slave units follow the Master unit:
1. On the Master unit set dipswitch 10 to the “On” postion.
2. On the Slave units set any dipswitches to the “On” postion,
©American DJ Supply® - www.americandj.com - LED Trispot Instruction Manual Page 8©American DJ Supply® - www.americandj.com - LED Trispot Instruction Manual Page 7
Stand By Blackout the unit
Function 1. Synchronous Strobe
2. Asynchronous Strobe
3. Sound Strobe
Show speed
1-3
N
O
DE
L
)
FF
O
D
EL(dnuo
Se
doM
LED Trispot Operating Instructions
except dipswitch 10. Dipswitch 10 must stay in the “Off” postion.
3. Now all connected units will follow the Master unit.
DMX Mode:
This unit can be a three channel or five channel DMX unit. Operating
through a DMX controller gives the user the freedom to create their
own programs tailored to their own individual needs.
1. This function will allow you to control each individual fixture’s
traits with a standard DMX 512 controller.
2. The LED Trispot can use either three DMX channels or five DMX
channels. Please see page 9 for the DMX values and traits.
3. To select the three channel mode put dipswitch #10 in the “On”
position. To select the five channel mode put dipswitch #10 in the
“Off” position.
4. Set your desired DMX address using dipswitches 1-9.
5. Finally, plug in the fixture via the XLR connections to any standard
DMX controller.
6. For help operating in DMX mode consult the manual included
with your DMX controller.
7. Please see the next page for DMX values and traits.
LED Trispot™ DMX Values & Traits - 3 Channels
Channel Value Function
1 RED
1 - 255 0% - 100%
2 GREEN
1 - 255 0% - 100%
3 BLUE
1 - 255 0% - 100%
LED Trispot™ DMX Values & Traits - 5 Channels
Channel Value Function
1 RED
1 - 255 0% - 100%
2 GREEN
1 - 255 0% - 100%
3 BLUE
1 - 255 0% - 100%
4 STROBE
0 - 15 OPEN
16 - 255 SLOW - FAST
5 MASTER DIMMER
1 - 255 0% - 100%
LED Trispot UC3 Control
©American DJ Supply® - www.americandj.com - LED Trispot Instruction Manual Page 10©American DJ Supply® - www.americandj.com - LED Trispot Instruction Manual Page 9
LED Trispot Cleaning
LED Trispot Warranty
Due to fog residue, smoke, and dust cleaning the internal and external optical lenses must be carried out periodically to optimize light
output.
1. Use normal glass cleaner and a soft cloth to wipe down the
outside casing.
2. Clean the external optics with glass cleaner and a soft cloth
every 20 days.
3. Always be sure to dry all parts completely before plugging
the unit back in.
Cleaning frequency depends on the environment in which the fixture
operates (i.e. smoke, fog residue, dust, dew).
LED Trispot Trouble Shooting
Listed below are a few common problems the user may encounter,
with solutions.
Unit not responding to DMX:
1. Check that the DMX cables are connected properly and are
wired correctly (pin 3 is “hot”; on some other DMX devices
pin 2 may be ‘hot’). Also, check that all cables are connected
to the right connectors; it does matter which way the inputs
and outputs are connected.
Unit does not respond to sound:
1. Quiet or high pitched sounds will not activate the unit.
If problems are not resolved; Contact American DJ® for service.
1-800-322-6337
MANUFACTURER’S LIMITED WARRANTY
A. American DJ, Inc. hereby warrants, to the original purchaser, American DJ and American
Audio products to be free of manufacturing defects in material and workmanship for a prescribed
period from the date of purchase (see specic warranty period on reverse). This warranty shall be
valid only if the product is purchased within the United States of America, including possessions
and territories. It is the owner’s responsibility to establish the date and place of purchase by acceptable evidence, at the time service is sought.
B. For warranty service you must obtain a Return Authorization number (RA#) before
sending back the product. Contact American DJ, Inc. Service Department at 800-322-6337. Send
the product only to the American DJ, Inc. factory. All shipping charges must be pre-paid. If the requested repairs or service (including parts replacement) are within the terms of this warranty, American DJ, Inc. will pay return shipping charges only to a designated point within the United States. If
the entire instrument is sent, it must be shipped in it’s original package. No accessories should be
shipped with the product. If any accessories are shipped with the product, American DJ, Inc. shall
have no liability whatsoever for loss of or damage to any such accessories, nor for the safe return
thereof.
C. This warranty is void if the serial number has been altered or removed; if the product is
modied in any manner which American DJ, Inc. concludes, after inspection, affects the reliability
of the product; if the product has been repaired or serviced by anyone other than the American DJ,
Inc. factory unless prior written authorization was issued to purchaser by American DJ, Inc.; if the
product is damaged because not properly maintained as set forth in the instruction manual.
D. This is not a service contract, and this warranty does not include maintenance, cleaning
or periodic check-up. During the period specied above, American DJ, Inc. will replace defective
parts at its expense with new or refurbished parts, and will absorb all expenses for warranty service
and repair labor by reason of defects in material or workmanship. The sole responsibility of American DJ, Inc. under this warranty shall be limited to the repair of the product, or replacement thereof,
including parts, at the sole discretion of American DJ. All products covered by this warranty were
manufactured after January 1, 1990, and bear identifying marks to that effect.
E. American DJ, Inc. reserves the right to make changes in design and/or improvements
upon its products without any obligation to include these changes in any products theretofore
manufactured. No warranty, whether expressed or implied, is given or made with respect to any accessory supplied with products described above. Except to the extent prohibited by applicable law,
all implied warranties made by American DJ, Inc. in connection with this product, including warran-
ties of merchantability or tness, are limited in duration to the warranty period set forth above. And
no warranties, whether expressed or implied, including warranties of merchantability or tness, shall
apply to this product after said period has expired. The consumer’s and/or Dealer’s sole remedy
shall be such repair or replacement as is expressly provided above; and under no circumstances
shall American DJ, Inc. be liable for any loss or damage, direct or consequential, arising out of the
use of, or inability to use, this product.
This warranty is the only written warranty applicable to American DJ and American Audio Products
and supersedes all prior warranties and written descriptions of warranty terms and
conditions heretofore published.
MANUFACTURER’S LIMITED WARRANTY PERIODS:
• All American Audio Products = 1-year (365 day) Limited Warranty (except V-Plus Series Ampliers)
• All American Audio V-Plus Series Ampliers = 3-year (1095 day) Limited Warranty
• American DJ Lighting and American DJ Branded Products = 1-year (365 day) Limited Warranty
(Such as: Special Effect Lighting, Intelligent Lighting, UV lighting, Strobes, Fog Machines, Bubble
Machines, Mirror Balls, Par Cans, Trussing, Lighting Stands etc. excluding Laser Products, lamps,
and Star Tec Series)
• American DJ Laser Products and Star Tec Products = 90-Day Limited Warranty
• American DJ L.E.D. Products = 3-year (1095 day) Limited Warranty (excluding motors which have
a 1-year (365 day Limited Warranty)
©American DJ Supply® - www.americandj.com - LED Trispot Instruction Manual Page 11 ©American DJ Supply® - www.americandj.com - LED Trispot Instruction Manual Page 12
LED Trispot Notes
LED Trispot Notes
©American DJ Supply® - www.americandj.com - LED Trispot Instruction Manual Page 13
©American DJ Supply® - www.americandj.com - LED Trispot Instruction Manual Page 14
LED Trispot Specifications
Model:
SPECIFICATIONS:
LED: 3W 3-in-1 RGB
Working Position: Any safe working position
Voltage: 100V~240V AC 50/60Hz
Power Consumption: 9 Watts
Fuse: 1Amp
Weight: 3lbs./ 1.2Kgs.
Dimensions: 7.75” (L) x 5” (W) x 7.71” (H)
198 x 127 x 196mm
DMX Channels: 3 & 5 DMX Channels
Colors: RGB Color Mixing
Warranty: 3 Year (1095 days)
Please Note: Specications and improvements in the design of
this unit and this manual are subject to change without any prior
written notice.
LED Trispot
©American DJ Supply® - www.americandj.com - LED Trispot Instruction Manual Page 15
©American DJ Supply
American DJ World Headquarters:
6122 S. Eastern Ave. Los Angeles, CA 90040 USA
Tel: 323-582-2650 / Fax: 323-725-6100
Web: www.americandj.com / E-mail: info@americandj.com
Loading...