SWEEPER BEAM QUAD LED
Sweeper Beam Quad LED General Information
Unpacking: Thank you for purchasing the Sweeper Beam Quad LED
by American DJ®. Every Sweeper Beam Quad LED has been thoroughly
tested and has been shipped in perfect operating condition. Carefully
check the shipping carton for damage that may have occurred during
shipping. If the carton appears to be damaged, carefully inspect your
xture for any damage and be sure all equipment necessary to operate the unit has arrived intact. In the event damage has been found
or parts are missing, please contact our toll free customer support
number for further instructions. Please do not return this unit to your
dealer without contacting customer support rst.
Introduction: The Sweeper Beam Quad LED is a intelligent, multi-
LED scanner. The Sweeper Beam Quad LED can operate as a stand
alone fixture or in a Master/Slave configuration. The Sweeper Beam
Quad LED has three operating modes; sound active mode, show
mode, and DMX control. This fixture is suitable for theaters, studios,
retail stores, and other similar locations. For best results use fog or
special effects smoke to enhance the beams projections.
Customer Support: ADJ Products, LLC provides a toll free cus-
tomer support line, to provide help and to answer any question should
you encounter problems during your set up or initial operation. You
may also visit us on the web at www.adj.com for any comments or
suggestions. Service Hours are Monday through Friday 8:00 a.m. to
4:30 p.m. Pacic Standard Time.
Voice: (800) 322-6337
Fax: (323) 582-2941
E-mail: support@americandj.com
5/13
Warning! To prevent or reduce the risk of electrical shock or re, do
not expose this unit to rain or moisture.
Warning! This may cause severe eye damage. Avoid looking directly
into the light source at all times!
User Instructions
ADJ Products, LLC - www.adj.com - Sweeper Beam Quad LED User Manual Page 2
Sweeper Beam Quad LED General Instructions
Sweeper Beam Quad LED Safety Precautions
To optimize the performance of this product, please read these
operating instructions carefully to familiarize yourself with the basic
operations of this unit. These instructions contain important safety
information regarding the use and maintenance of this unit. Please
keep this manual with the unit, for future reference.
Sweeper Beam Quad LED Features
• DMX-512 Protocol
• 4 DMX Channel Modes (1 Channel Mode, 6 Channel Mode, 35
Channel Mode, & 39 Channel Mode)
• 3 Operating Modes - Sound Active, Show Mode, and DMX Control
• Internal Microphone
• Digital Display for Address and Function Setting
• UC3 Controller (Not Included)
Sweeper Beam Quad LED Warranty Registration
The Sweeper Beam Quad LED carries a 3 year (1095 days) limited
warranty. Please fill out the enclosed warranty card to validate your
purchase and warranty. You may also register your product online
at www. americandj.com. All returned service items whether under
warranty or not, must be freight pre-paid and accompany a return
authorization (R.A.) number. If the unit is under warranty you must
provide a copy of your proof of purchase invoice. Please contact ADJ
Products, LLC customer support for a R.A. number.
Sweeper Beam Quad LED Handling Precautions
Caution! There are no user serviceable parts inside this unit. Do not
attempt any repairs yourself, doing so will void your manufactures
warranty. In the unlikely event your unit may require service please
contact ADJ Products, LLC.
ADJ Products, LLC will not accept any liability for any resulting damages caused by the non-observance of this manual or any unauthor-
ized modication to this unit.
For Your Own Personal Safety, Please Read and Understand This
Manual Completely Before You Attempt To Install Or Operate
This Unit!
• To reduce the risk of electrical shock or re, do not expose this unit
rain or moisture
• Do not spill water or other liquids into or on to your unit.
• Be sure that the local power outlet match that of the required volt-
age for your unit.
• Do not attempt to operate this unit if the power cord has been
frayed or broken.
• Do not attempt to remove or break off the ground prong from
the electrical cord. This prong is used to reduce the risk of electrical
shock and re in case of an internal short.
• Disconnect from main power before making any type of connection.
• Do not remove the cover under any conditions. There are no user
serviceable parts inside.
• Never operate this unit when it’s cover is removed.
• Always be sure to mount this unit in an area that will allow proper
ventilation. Allow about 6” (15cm) between this device and a wall.
• Do not attempt to operate this unit, if it becomes damaged.
• This unit is intended for indoor use only, use of this product out-
doors voids all warranties.
• Always mount this unit in safe and stable matter.
• Power-supply cords should be routed so that they are not likely to
be walked on or pinched by items placed upon or against them,
paying particular attention to cords at plugs, convenience recep-
tacles, and the point where they exit from the appliance.
• Cleaning -The fixture should be cleaned only as recommended by
the manufacturer. See page 21 for cleaning details.
• Heat -This fixture should be situated away from heat sources such
as radiators, heat registers, stoves, or other appliances (including
amplifiers) that produce heat.
• The fixture should be serviced by qualified service personnel when:
A. Objects have fallen, or liquid has been spilled into the appliance.
B. The appliance has been exposed to rain or water.
C. The appliance does not appear to operate normally or exhibits a
marked change in performance.
ADJ Products, LLC - www.adj.com - Sweeper Beam Quad LED User Manual Page 4ADJ Products, LLC - www.adj.com - Sweeper Beam Quad LED User Manual Page 3
Sweeper Beam Quad LED Hanging Precautions
Sweeper Beam Quad LED Set Up
Fixture installation must always be secured with a secondary
safety attachment, such as an appropriate safety cable.
Regardless of the rigging option you choose for your Sweeper
Beam Quad LED always be sure to secure your xture with a
safety cable (not included).
Caution: For added protection mount the xtures in areas outside of walking paths, seating areas, or areas were the xture
might be reached by unauthorized personal.
Before mounting the xture to any surface, make sure that the
installation area can hold a minimum point load of 10 times the
device’s weight.
To avoid injury, never stand directly below the device when
mounting, removing, or servicing the xture.
Always use and install a safety cable ( not included) as a safety
measure to prevent accidental damage and/or injury in the
event the clamp fails.
Be sure to complete all rigging and installation procedures
before connecting the main power cord to the appropriate wall
outlet.
Power Supply: The ADJ Sweeper Beam Quad LED contains a auto-
matic voltage switch, which will auto sense the voltage when it is
plugged into the power source. With this switch there is no need to
worry about the correct power voltage, this unit can be plugged in
anywhere.
DMX-512: DMX is short for Digital Multiplex. This is a universal pro-
tocol used by most lighting and controller manufactures as a form of
communication between intelligent fixtures and controllers. A DMX
controller sends DMX data instructions from the controller to the fixture. DMX data is sent as serial data that travels from fixture to fixture
via the DATA “IN” and DATA “OUT” XLR terminals located on all DMX
fixtures (most controllers only have a DATA “OUT” terminal).
DMX Linking: DMX is a language allowing all makes and models
of different manufactures to be linked together and operate from a
single controller, as long as all xtures and the controller are DMX
compliant. To ensure proper DMX data transmission, when using
several DMX fixtures try to use the shortest cable path possible. The
order in which fixtures are connected in a DMX line does not influence
the DMX addressing. For example; a fixture assigned a DMX address
of 1 may be placed anywhere in a DMX line, at the beginning, at the
end, or anywhere in the middle. Therefore, the first fixture controlled
by the controller could be the last fixture in the chain. When a fixture
is assigned a DMX address of 1, the DMX controller knows to send
DATA assigned to address 1 to that unit, no matter where it is located
in the DMX chain.
Data Cable (DMX Cable) Requirements (For DMX and Master/Slave
Operation): The Sweeper Beam Quad LED can be controlled via
DMX-512 protocol. The Sweeper Beam Quad LED
has 4 DMX Channel Modes. The DMX address is
set electronically using the controls on the rear
panel of the unit. Your unit and your DMX control-
ler require a approved DMX-512 110 Ohm Data
cable for data input and data output (Figure 1). We
recommend Accu-Cable DMX cables. If you are
making your own cables, be sure to use standard
110-120 Ohm shielded cable (This cable may be
purchased at almost all professional sound and lighting stores). Your
ADJ Products, LLC - www.adj.com - Sweeper Beam Quad LED User Manual Page 6ADJ Products, LLC - www.adj.com - Sweeper Beam Quad LED User Manual Page 5
Figure 1
Sweeper Beam Quad LED Set Up
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
DMX512
DMX+,DMX-,COMMON
1
2
3
Termination reduces signal errors and
avoids signal transmission problems
and interference. It is always advisable
to connect a DMX terminal, (Resistance
120 Ohm 1/4 W) between PIN 2 (DMX-)
and PIN 3 (DMX +) of the last fixture.
POWER
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
Sweeper Beam Quad LED Set Up
cables should be made with a male and female XLR connector on
either end of the cable. Also remember that DMX cable must be daisy
chained and cannot be split.
Notice: Be sure to follow gures two and three when making your own
cables. Do not use the ground lug on the XLR connector. Do not con-
nect the cable’s shield conductor to the ground lug or allow the shield
conductor to come in contact with the XLR’s outer casing. Grounding
the shield could cause a short circuit and erratic behavior.
COMMON
1
DMX512 IN
3
3-PIN XLR
2
Figure 2
XLR Pin Conguration
Pin 1 = Ground
Pin 2 = Data Compliment (negative)
Pin 3 = Data True (positive)
XLR Male Socket
1 Ground
Figure 3
DMX512 OUT
3-PIN XLR
2 Cold
3 Hot
1
3
2
XLR Female Socket
2 Cold
DMX +
DMX -
1 Ground
3 Hot
5-Pin XLR DMX Connectors.
Some manufactures use 5-pin DMX-
512 data cables for DATA transmission in place of 3-pin. 5-pin DMX
xtures may be implemented in a 3-pin DMX line. When inserting standard 5-pin data cables in to a 3-pin line a cable adaptor must be used,
these adaptors are readily available at most electric stores. The chart
below details a proper cable conversion.
3-Pin XLR to 5-Pin XLR Conversion
Conductor 5-Pin XLR Male (In)3-Pin XLR Female (Out)
Ground/Shield
Data Compliment (- signal)
Data True (+ signal)
Not Used
Not Used
Pin 1
Pin 2
Pin 3
Pin 1
Pin 2
Pin 3
Pin 4 - Do Not Use
Pin 5 - Do Not Use
Special Note: Line Termination.
used, you may need to use a terminator on the last unit to avoid erratic
behavior. A terminator is a 110-120 ohm 1/4 watt resistor which is con-
When longer runs of cable are
nected between pins 2 and 3 of a male XLR connector (DATA + and
DATA -). This unit is inserted in the female XLR connector of the last
unit in your daisy chain to terminate the line. Using a cable terminator
(ADJ part number Z-DMX/T) will decrease the possibilities of erratic
behavior.
ADJ Products, LLC - www.adj.com - Sweeper Beam Quad LED User Manual Page 7 ADJ Products, LLC - www.adj.com - Sweeper Beam Quad LED User Manual Page 8
Termination reduces signal errors and
1
avoids signal transmission problems
3
and interference. It is always advisable
2
to connect a DMX terminal, (Resistance
120 Ohm 1/4 W) between PIN 2 (DMX-)
and PIN 3 (DMX +) of the last fixture.
Figure 4
Sweeper Beam Quad LED System Menu
Sweeper Beam Quad LED System Menu
System Menu: When making adjustments press ENTER
to conrm your setup and then press and hold the MENU
button for at least 3 seconds. To exit without making any
adjustments press the MENU button.
ADDR - DMX Address Setting.
1. Press the either the MENU, UP, or DOWN buttons until
“ADDR” is displayed, press ENTER.
2. The current address will now be displayed and ashing.
Press the UP or DOWN buttons to nd your desired address.
Press ENTER and then press and hold the MENU button to set
your desired DMX address.
CHND - This will let select your desired DMX channel
mode.
1. Press the either the MENU button until “CHND” is displayed,
press ENTER. Either “1CH”, “6CH”, “35CH”, or “39CH” will be
displayed
2. Press the UP or DOWN buttons to choose your desired DMX
mode and press ENTER to conm and exit.
SLND - This will let you set unit as a master or slave in a
master/slave conguration.
1. Press the MENU button until “SLND” is displayed, press
ENTER. Either “MAST”, “SL 1” or “SL 2” will be displayed.
2. Press the UP or DOWN buttons until your desired setting is
displayed, press ENTER and then press and hold the MENU
button to conm.
NOTE: In a Master/Slave conguration you can set one xture
to Master and then set the next xture to “SL 2”, the xtures
will now have contrast movement to each other.
ADJ Products, LLC - www.adj.com - Sweeper Beam Quad LED User Manual Page 10ADJ Products, LLC - www.adj.com - Sweeper Beam Quad LED User Manual Page 9
Sweeper Beam Quad LED System Menu
Sweeper Beam Quad LED System Menu
SET - This will set the Sweeper to a preset angle.
1. Press the either the MENU button until “SET” is displayed,
press ENTER. Either “150”, “120”, or “90” will be displayed,
these are the preset angles.
2. Press the UP or DOWN buttons to choose your desired angle
and press ENTER to conm and exit.
SHND: SH 0 - SH16 - Show modes 0-16 (Factory
programs). Show mode can run with or without sound active
mode.
1. Press the MENU button until “SHND” is displayed, press
ENTER.
2. “Sh X” will now be displayed, “X” representing a number
between 0-16. Programs 1-16 are factory programs, while “Sh
0” is random mode. Press the UP or DOWN buttons to nd your
desired show.
3. When you have found your desired show press ENTER, then
press and hold the MENU button for at least 3 seconds to acti-
vate.
SOUN - Sound Active mode.
1. Press the MENU button until “SOUN” is displayed, press
ENTER.
2. The display will show either “ON” or “OFF”. Press the UP or
DOWN buttons to select “ON” to activate sound active mode,
or “OFF” to deactivate sound active mode.
3. Press ENTER, and then press and hold the MENU button for
at least 3 seconds to activate.
SENS - Sound sensitivity control.
1. Press the MENU button until “SENS” is displayed, press ENTER.
2. The display will show a number between 0-100. Press the UP or
DOWN buttons to adjust the sound sensitivity. 0 being the least sensitive and 100 the most sensitive.
3. Press the ENTER button to conrm.
DNST - This mode can be used as a precaution mode, that
in case the DMX signal is lost, the operating mode chosen in
the setup is the running mode the xture will go into when
the DMX signal is lost. You can also set this as the operating mode you would like the unit to return to when power is
applied.
1. Press the MENU button until “DNST” is displayed, press
ENTER.
2. Either “MAST”, “BLND”, or “LAST” will be displayed. Choose
an operating mode you would like the unit to start up in when
power is applied or the DMX signal is lost.
• MAST (Master Slave) - If the DMX signal is lost or power is
applied, the unit will automatically go into Master Slave mode.
• BLND (Blackout) - If the DMX signal is lost or power is applied,
the unit will automatically go into stand by mode.
• LAST (Last State) - If the DMX signal is lost the xture will stay
in the last DMX set up. If power is applied and this mode is set,
the unit will automatically go into the last DMX set up.
3. Press ENTER to conrm your desired set up
LED - With this function you can have the LED display
turn off after 10 seconds.
ADJ Products, LLC - www.adj.com - Sweeper Beam Quad LED User Manual Page 11
1. Press the MENU button until “LED” is displayed, press
ADJ Products, LLC - www.adj.com - Sweeper Beam Quad LED User Manual Page 12
Sweeper Beam Quad LED System Menu Sweeper Beam Quad LED System Menu
ENTER.
2. The display will show either “ON” or “OFF”. Press the UP or
DOWN buttons to select “ON” to keep the LED display on at
all times, or “OFF” to switch to have the LED display switch off
after 10 seconds. To make the display reappear, press and hold
the MENU button for at least 5 secs.
3. Press ENTER to conrm. To make the display reappear, press
and hold the MENU button for at least 5 secs.
DISP - This will “ip” the LED display 180º.
1. Press the MENU button until “DISP” is displayed, press
ENTER.
2. Either “DISP” or “DSIP” will now be displayed. Press the
ENTER button to “ip” the display.
TILT - This function activates tilt inversion.
1. Press the MENU button until “TILT” is displayed, press
ENTER.
2. The display will show either “YES” or “NO”. Press the UP
or DOWN buttons to select “YES” to activate tilt inversion, or
“NO” to deactivate tilt inversion.
Example: When using 35 Channel mode (LED 1) can start at
either end of the bar depending on this functions set up.
1. Press the MENU button until “REV” is displayed, press
ENTER.
2. The display will show either “YES” or “NO”. Press the UP or
DOWN buttons to select “YES” which will have the projector
lenses/LEDs light up right to left, or “NO” which will have the
projector lenses/LEDs light up left to right.
3. Press ENTER to conrm.
TEST - This function will run a self test program.
1. Press the MENU button until “TEST” is displayed, press
ENTER.
2. The xture will now run a self test.
TEMP - With this function you can check the current
temperature of the unit.
1. Press the MENU button until “TEMP” is displayed, press
ENTER.
2. The current temperature of the xture will now be displayed.
Press MENU to exit.
3. Press ENTER, and then press and hold the MENU button for
at least 3 seconds to activate.
REV - This function is used in conjuction with DMX
mode. The direction in which the projector lenses/LEDs
light up can be reversed so that the LED line up can start at
either end of the bar. This feature is useful when the unit is
installed in a reversed orientation so the unit itself does not
have to be uninstalled and reversed.
ADJ Products, LLC - www.adj.com - Sweeper Beam Quad LED User Manual Page 13 ADJ Products, LLC - www.adj.com - Sweeper Beam Quad LED User Manual Page 14
FHRS - With this function you can display the running
time of the xture.
1. Press the MENU button until “FHRS” is displayed, press
ENTER.
2. The running time of the xture will now be displayed. Press
MENU to exit.
Sweeper Beam Quad LED System Menu
Sweeper Beam Quad LED Operation
VER - With this function you can display the version soft-
ware of the xture.
1. Tap the MENU button until “VER” is displayed, press ENTER.
2. The software version will now be displayed. Press MENU to
exit.
RSET - Use this function to reset the unit.
1. Press the MENU button until “RSET” is displayed, press
ENTER.
2. The xture will now reset.
Sweeper Beam Quad LED UC3 Control
Blackout Blackout the fixture
Function
Mode
Sweeper Beam Quad LED Power Cord Daisy Chain
With this feature you can connect the xtures to one another
using the IEC input and output sockets. The quantity that can be
connected is 4 xtures maximum. After 4 xtures you will need
to use a new power outlet. They must be the same xtures. DO
NOT mix xtures.
1. Sound Strobe (Full on).
2. Auto Strobe (Full on).
Random Show(LED OFF)
Select Shows (Show 1-16).
Show(LED ON)
Operating Modes: The Sweeper Beam Quad LED can operate
in three different modes. In each mode you can run the fixture
as a stand alone fixture or in a master/slave confiugration. This
next section will detail the differences in the operating modes.
• Sound Active mode -
The fixture will react to sound, chasing through the built-in programs.
• Show mode -
Choose 1 of 12 show modes to run.
• DMX control mode -
This function will allow you to control each individual fixtures traits
with a standard DMX-512 controller such as the Elation® Show
Designer.
™
Master-Slave Operation This function will allow you to link up to 16
units together and operate without a controller. The units will be sound
activated. In Master-Slave operation one unit will act as the controlling
unit and the others will react to the controlling units programs. Any unit
can act as a Master or as a Slave.
1. Using approved DMX data cables, daisy chain your units togeth-
er via the XLR connector on the rear of the units. Remember the
Male XLR connector is the input and the Female XLR connector
is the output. The rst unit in the chain (master) will use the female
XLR connector only - The last unit in the chain will use the male
XLR connector only. For longer cable runs we suggest a termina-
tor at the last fixture.
2. Set the Master unit to your desired operating mode, then set the
unit to the Master setting.
3. For the slave units press the MENU button until “SLND” is dis-
played, and Press ENTER. Set the slave units to either “SL 1” or
“SL 2”.
4. The slave units will now follow the Master unit.
Universal DMX Control: This function allows you to use a Elation®
universal DMX-512 controller to control the chases and patterns,
dimmer and strobe. A DMX controller allows you to create unique
programs tailored to your individual needs.
1. The Sweeper Beam Quad LED has 4 DMX Channel modes; 1
ADJ Products, LLC - www.adj.com - Sweeper Beam Quad LED User Manual Page 16ADJ Products, LLC - www.adj.com - Sweeper Beam Quad LED User Manual Page 15
Sweeper Beam Quad LED Operation
Sweeper Beam Quad LED 1 DMX Channel Mode
Channel, 6 Channels, 35 Channels, or 39 Channels. See pages
18-24 for detailed description of the DMX values and traits.
2. To control your fixture in DMX mode, follow the set-up procedures
on pages 6-8 as well as the set-up specifications that are includ ed with your DMX controller.
3. Use the controller’s faders to control the various DMX fixture traits.
4. This will allow you to create your own programs.
5. Follow the instructions on page 10 to set the DMX address.
6. For longer cable runs (more than a 100 feet) use a terminator on
the last fixture.
7. For help operating in DMX mode consult the manual included
with your DMX controller.
Sound Active Mode: This mode allows either single unit or several
units linked together, to run to the beat of the music.
1. Tap the MENU button until “SOUN” is displayed, and press
ENTER.
2. Tap the UP or DOWN buttons to choose either OFF or ON, and
press ENTER, then press and hold MENU for 3 seconds to con rm. To adjust sound sensitivity see page 12.
3. The optional UC3 Controller (not included) may be used to con trol different functions including blackout.
Show Mode: In this mode you can choose 1 of 16 show modes to
run.
1. Tap the MENU button until “SHND” is displayed, and press
ENTER.
2. Tap the UP or DOWN buttons until you nd your desired show,
and press ENTER then press and hold MENU for 3 seconds to
con rm. See page 11 for more info.
3. The optional UC3 Controller (not included) may be used to con trol different functions including blackout.
Channel Value Function
1 SHOWS
0 - 7 BLACKOUT
8 - 22 SHOW 1
23 - 37 SHOW 2
38 - 52 SHOW 3
53 - 67 SHOW 4
68 - 82 SHOW 5
83 - 97 SHOW 6
98 - 112 SHOW 7
113 - 127 SHOW 8
128 - 142 SHOW 9
143 - 157 SHOW 10
158 - 172 SHOW 11
173 - 187 SHOW 12
188 - 202 SHOW 13
203 - 217 SHOW 14
218 - 232 SHOW 15
233 - 247 SHOW 16
248 - 255 RANDOM SHOW
ADJ Products, LLC - www.adj.com - Sweeper Beam Quad LED User Manual Page 17 ADJ Products, LLC - www.adj.com - Sweeper Beam Quad LED User Manual Page 18
Sweeper Beam Quad LED 6 DMX Channel Mode
Sweeper Beam Quad LED 35 DMX Channel Mode
Channel Value Function
1 0 - 255 TILT -30° -210°
2 TILT MOVEMENT MACRO
0 - 7 NO FUNCTION
8 - 43 TILT MOVEMENT MACRO 60° -120°
44 - 79 TILT MOVEMENT MACRO 45° -135°
80 - 115 TILT MOVEMENT MACRO 30° -150°
116 - 151 TILT MOVEMENT MACRO 0° -180°
152 - 187 TILT MOVEMENT MACRO -30° -210°
188 - 223 TILT MOVEMENT MACRO 0° -90°
224 - 255 TILT MOVEMENT MACRO 90° -180°
3 TILT MOVEMENT MACRO SPEED
0 - 7 NO FUNCTION
8 - 255 SLOW - FAST
4 CHASES
0 - 7 NO FUNCTION
8 - 22 CHASE 1
23 - 37 CHASE 2
38 - 52 CHASE 3
53 - 67 CHASE 4
68 - 82 CHASE 5
83 - 97 CHASE 6
98 - 112 CHASE 7
113 - 127 CHASE 8
128 - 142 CHASE 9
143 - 157 CHASE 10
158 - 172 CHASE 11
173 - 187 CHASE 12
188 - 202 CHASE 13
203 - 217 CHASE 14
218 - 232 CHASE 15
233 - 247 CHASE 16
248 - 255 FULL ON
5 0 - 255 CHASE SPEED SLOW - FAST
6 0 - 255 MASTER DIMMER 0% - 100%
ADJ Products, LLC - www.adj.com - Sweeper Beam Quad LED User Manual Page 19 ADJ Products, LLC - www.adj.com - Sweeper Beam Quad LED User Manual Page 20
Channel Value Function
1 0 - 255 TILT -30° -210°
2 0 - 255 MASTER DIMMER 0% - 100%
3 STROBING
0 - 15 NO FUNCTION
16 - 131 STROBING SLOW - FAST
132 - 139 NO FUNCTION
140 - 181 SLOW OPEN - FAST CLOSE
182 - 189 NO FUNCTION
190 - 231 SLOW CLOSE - FAST OPEN
232 - 239 NO FUNCTION
240 - 247 SOUND ACTIVE STROBING
248 - 255 NO FUNCTION
4 0 - 255 RED (LENS 1)
5 0 - 255 GREEN (LENS 1)
6 0 - 255 BLUE (LENS 1)
7 0 - 255 WHITE (LENS 1)
8 0 - 255 RED (LENS 2)
9 0 - 255 GREEN (LENS 2)
10 0 - 255 BLUE (LENS 2)
11 0 - 255 WHITE (LENS 2)
12 0 - 255 RED (LENS 3)
13 0 - 255 GREEN (LENS 3)
14 0 - 255 BLUE (LENS 3)
15 0 - 255 WHITE (LENS 3)
16 0 - 255 RED (LENS 4)
17 0 - 255 GREEN (LENS 4)
18 0 - 255 BLUE (LENS 4)
19 0 - 255 WHITE (LENS 4)
20 0 - 255 RED (LENS 5)
21 0 - 255 GREEN (LENS 5)
22 0 - 255 BLUE (LENS 5)
23 0 - 255 WHITE (LENS 5)
24 0 - 255 RED (LENS 6)
25 0 - 255 GREEN (LENS 6)
Sweeper Beam Quad LED 35 DMX Channel Mode
Sweeper Beam Quad LED 39 DMX Channel Mode
Channel Value Function
26 0 - 255 BLUE (LENS 6)
27 0 - 255 WHITE (LENS 6)
28 0 - 255 RED (LENS 7)
29 0 - 255 GREEN (LENS 7)
30 0 - 255 BLUE (LENS 7)
31 0 - 255 WHITE (LENS 7)
32 0 - 255 RED (LENS 8)
33 0 - 255 GREEN (LENS 8)
34 0 - 255 BLUE (LENS 8)
35 0 - 255 WHITE (LENS 8)
Channel Value Function
1 0 - 255 TILT -30° -210°
2 TILT MOVEMENT MACRO
0 - 7 NO FUNCTION
8 - 43 TILT MOVEMENT MACRO 60° -120°
44 - 79 TILT MOVEMENT MACRO 45° -135°
80 - 115 TILT MOVEMENT MACRO 30° -150°
116 - 151 TILT MOVEMENT MACRO 0° -180°
152 - 187 TILT MOVEMENT MACRO -30° -210°
188 - 223 TILT MOVEMENT MACRO 0° -90°
224 - 255 TILT MOVEMENT MACRO 90° -180°
3 TILT MOVEMENT MACRO SPEED
0 - 7 NO FUNCTION
8 - 255 SLOW - FAST
4 CHASES
0 - 7 NO FUNCTION
8 - 22 CHASE 1
23 - 37 CHASE 2
38 - 52 CHASE 3
53 - 67 CHASE 4
68 - 82 CHASE 5
83 - 97 CHASE 6
98 - 112 CHASE 7
113 - 127 CHASE 8
128 - 142 CHASE 9
143 - 157 CHASE 10
158 - 172 CHASE 11
173 - 187 CHASE 12
188 - 202 CHASE 13
203 - 217 CHASE 14
218 - 232 CHASE 15
233 - 247 CHASE 16
248 - 255 FULL ON
5 0 - 255 CHASE SPEED SLOW - FAST
6 0 - 255 MASTER DIMMER 0% - 100%
ADJ Products, LLC - www.adj.com - Sweeper Beam Quad LED User Manual Page 22ADJ Products, LLC - www.adj.com - Sweeper Beam Quad LED User Manual Page 21
Sweeper Beam Quad LED 39 DMX Channel Mode
Sweeper Beam Quad LED 39 DMX Channel Mode
Channel Value Function
7 STROBING
0 - 15 NO FUNCTION
16 - 131 STROBING SLOW - FAST
132 - 139 NO FUNCTION
140 - 181 SLOW OPEN - FAST CLOSE
182 - 189 NO FUNCTION
190 - 231 SLOW CLOSE - FAST OPEN
232 - 239 NO FUNCTION
240 - 247 SOUND ACTIVE STROBING
248 - 255 NO FUNCTION
8 0 - 255 RED (LENS 1)
9 0 - 255 GREEN (LENS 1)
10 0 - 255 BLUE (LENS 1)
11 0 - 255 WHITE (LENS 1)
12 0 - 255 RED (LENS 2)
13 0 - 255 GREEN (LENS 2)
14 0 - 255 BLUE (LENS 2)
15 0 - 255 WHITE (LENS 2)
16 0 - 255 RED (LENS 3)
17 0 - 255 GREEN (LENS 3)
18 0 - 255 BLUE (LENS 3)
19 0 - 255 WHITE (LENS 3)
20 0 - 255 RED (LENS 4)
21 0 - 255 GREEN (LENS 4)
22 0 - 255 BLUE (LENS 4)
23 0 - 255 WHITE (LENS 4)
24 0 - 255 RED (LENS 5)
25 0 - 255 GREEN (LENS 5)
26 0 - 255 BLUE (LENS 5)
27 0 - 255 WHITE (LENS 5)
28 0 - 255 RED (LENS 6)
29 0 - 255 GREEN (LENS 6)
30 0 - 255 BLUE (LENS 6)
31 0 - 255 WHITE (LENS 6)
ADJ Products, LLC - www.adj.com - Sweeper Beam Quad LED User Manual Page 23
Channel Value Function
32 0 - 255 RED (LENS 7)
33 0 - 255 GREEN (LENS 7)
34 0 - 255 BLUE (LENS 7)
35 0 - 255 WHITE (LENS 7)
36 0 - 255 RED (LENS 8)
37 0 - 255 GREEN (LENS 8)
38 0 - 255 BLUE (LENS 8)
39 0 - 255 WHITE (LENS 8)
ADJ Products, LLC - www.adj.com - Sweeper Beam Quad LED User Manual Page 24
Sweeper Beam Quad LED Fuse Replacement
Disconnect the unit from its power source. Remove the power cord
from the unit. Once the cord has been removed, you will find that
the fuse holder is located inside the power socket. Insert a flat-head
screw driver into the power socket and gently pry out the fuse holder.
Remove the bad fuse and replace with a new one. The fuse holder also
has a holder for a spare fuse.
Sweeper Beam Quad LED Cleaning
Fixture Cleaning: Due to fog residue, smoke, and dust cleaning the
internal and external optical lenses and mirror should be carried out
periodically to optimize light output. Cleaning frequency depends on
the environment in which the fixture operates (I.e. smoke, fog residue,
dust, dew). In heavy club use we recommend cleaning on a monthly
basis. Periodic cleaning will ensure longevity, and crisp output.
1. Use normal glass cleaner and a soft cloth to wipe down the out side casing.
2. Use a brush to wipe down the cooling vents and fan grill.
3. Clean the external optics and mirror with glass cleaner and a soft
cloth every 20 days.
4. Clean the internal optics with glass cleaner and a soft cloth every
30-60 days.
5. Always be sure to dry all parts completely before plugging the unit
back in.
Sweeper Beam Quad LED Trouble Shooting
Trouble Shooting: Listed below are a few common problems that
you may encounter, with solutions.
No light output from the unit;
1. Be sure the external fuse has not blown. The fuse is located on
the rear panel of the unit.
2. Be sure the fuse holder is completely and properly seated.
Unit does not respond to sound;
1. Low frequencies (bass) should cause the unit to react to sound.
Tapping on the microphone, quiet or high pitched sounds may
not activate the unit.
ADJ Products, LLC - www.adj.com - Sweeper Beam Quad LED User Manual Page 25 ADJ Products, LLC - www.adj.com - Sweeper Beam Quad LED User Manual Page 26
Sweeper Beam Quad LED Warranty
MANUFACTURER’S LIMITED WARRANTY
A. ADJ Products, LLC hereby warrants, to the original purchaser, ADJ Products, LLC products
to be free of manufacturing defects in material and workmanship for a prescribed period from
the date of purchase (see specific warranty period on reverse). This warranty shall be valid only if the
product is purchased within the United States of America, including possessions and
territories. It is the owner’s responsibility to establish the date and place of purchase by acceptable
evidence, at the time service is sought.
B. For warranty service you must obtain a Return Authorization number (RA#)
before sending back the product–please contact ADJ Products, LLC Service Department
at 800-322-6337. Send the product only to the ADJ Products, LLC factory. All
shipping charges must be pre-paid. If the requested repairs or service (including
parts replacement) are within the terms of this warranty, ADJ Products, LLC will pay return
shipping charges only to a designated point within the United States. If the entire instrument is
sent, it must be shipped in it’s original package. No accessories should be shipped with the product. If
any accessories are shipped with the product, ADJ Products, LLC shall have no liability whatsoever for
loss of or damage to any such accessories, nor for the safe return thereof.
C. This warranty is void if the serial number has been altered or removed; if the product is modified in any
manner which ADJ Products, LLC concludes, after inspection, affects the reliability of the product; if the
product has been repaired or serviced by anyone other than the ADJ Products, LLC factory unless prior
written authorization was issued to purchaser by ADJ Products, LLC; if the product is damaged because
not properly maintained as set forth in the instruction manual.
D. This is not a service contract, and this warranty does not include maintnance, cleaning or periodic check
up. During the period specified above, ADJ Products, LLC will replace defective parts at its expense
with new or refurbished parts, and will absorb all expenses for warranty service and repair labor by
reason of defects in material or workmanship. The sole responsibility of ADJ Products, LLC under this
warranty shall be limited to the repair of the product, or replacement thereof, including parts, at the sole
discretion of ADJ Products, LLC. All products covered by this warranty were manufactured after August
15, 2012, and bear indentifying marks to that effect.
E. ADJ Products, LLC reserves the right to make changes in design and/or improvements upon its products
without any obligation to include these changes in any products theretofore manufactured.
No warranty, whether expressed or implied, is given or made with respect to any accessory supplied with
products described above. Except to the extent prohibited by applicable law, all implied warranties made
by ADJ Products, LLC in connection with this product, including warranties of merchantability or fitness,
are limited in duration to the warranty period set forth above. And no warranties, whether expressed or
implied, including warranties of merchantability or fitness, shall apply to this product after said period
has expired. The consumer’s and/or Dealer’s sole remedy shall be such repair or replacement as is
expressly provided above; and under no circumstances shall ADJ Products, LLC be liable for any loss or
damage, direct or consequential, arising out of the use of, or inability to use, this product.
This warranty is the only written warranty applicable to ADJ Products, LLC Products and
supersedes all prior warranties and written descriptions of warranty terms and conditions heretofore
published.
MANUFACTURER’S LIMITED WARRANTY PERIODS:
•LightingProducts=1-year(365days)LimitedWarranty(Such as: Special Effect Lighting, Intelligent
Lighting, UV lighting, Strobes, Fog Machines, Bubble Machines, Mirror Balls, Par Cans, Trussing,
Lighting Stands etc. excluding LED and lamps)
•LaserProducts=90-DayLimitedWarranty
•L.E.D.Products=3-year(1095days)LimitedWarranty(excluding motors, PCB boards, and power
supplies, which have a 1-year (365 day Limited Warranty) and batteries which have a 180 day
limited warranty). Only the L.E.D.s carry a 3-year warranty
Sweeper Beam Quad LED Specifications
Model: Sweeper Beam Quad LED
Voltage: 100V ~ 240V/50~60Hz
LEDs: 8 x 8W RGBW LEDs
Power Consumption: 81W
Power Cord Daisy Chain: 4 Fixtures Max.
Beam Angle: 3.4 Degrees
Dimensions: 38.5”(L) x 3”(W) x 5.25”(H)
973 x 73 x 132mm
Colors: RGBW
Weight: 14 Lbs. / 6.3 kgs.
Fuse: 7A
Duty Cycle: None
DMX: 1, 6, 35, & 39 DMX Channel Modes
Working Position: Any Safe, Secure Position
Warranty: 3 Year (1095 days)
Auto Sensing Voltage: This xture contains a automatic volt-
age switch, which will auto sense the voltage when it is plugged
into the power source.
Please Note: Specications and improvements in the design
of this unit and this manual are subject to change without any
prior written notice.
ADJ Products, LLC - www.adj.com - Sweeper Beam Quad LED User Manual Page 27
ADJ Products, LLC
6122 S. Eastern Ave. Los Angeles, CA 90040 USA
Tel: 323-582-2650 / Fax: 323-725-6100
Web: www.adj.com / E-mail: info@adj.com
A.D.J. Supply Europe B.V.
Junostraat 2
6468 EW Kerkrade
Netherlands
service@adj.eu / www.adj.eu
Tel: +31 45 546 85 00 / Fax: +31 45 546 85 99
Loading...