Stinger Spot
©2017 ADJ Products, LLC all rights reserved. Information,
specications, diagrams, images, and instructions herein are
subject to change without notice. ADJ Products, LLC logo and
identifying product names and numbers herein are trademarks
of ADJ Products, LLC. Copyright protection claimed includes all
forms and matters of copyrightable materials and information
now allowed by statutory or judicial law or hereinafter granted.
Product names used in this document may be trademarks or
registered trademarks of their respective companies and are
hereby acknowledged. All non-ADJ Products, LLC brands and
product names are trademarks or registered trademarks of their
respective companies.
ADJ Products, LLC and all aliated companies hereby disclaim any and all liabilities for property, equipment, building,
and electrical damages, injuries to any persons, and direct or
indirect economic loss associated with the use or reliance of
any information contained within this document, and/or as a
result of the improper, unsafe, unsucient and negligent assembly, installation, rigging, and operation of this product.
2/17
User Instructions
Europe Energy Saving Notice
Energy Saving Matters (EuP 2009/125/EC)
Saving electric energy is a key to help protecting the enviroment.
Please turn o all electrical products when they are not in use. To
avoid power consumption in idle mode, disconnect all electrical
equipment from power when not in use. Thank you!
Stinger Spot General Information
Stinger Spot General Instructions
Unpacking: Thank you for purchasing the Stinger Spot by ADJ Prod-
ucts, LLC. Every Stinger Spot has been thoroughly tested and has
been shipped in perfect operating condition. Carefully check the shipping carton for damage that may have occurred during shipping. If the
carton appears to be damaged, carefully inspect your xture for any
damage and be sure all equipment necessary to operate the unit has
arrived intact. In the event damage has been found or parts are missing, please contact our toll free customer support number for further
instructions. Please do not return this unit to your dealer without contacting customer support rst.
Introduction: The Stinger Spot is a DMX intelligent, moving head,
mini LED fixture. The Stinger Spot can operate as a stand alone fixture
or in a Master/Slave configuration. The Stinger Spot has three operat-
ing modes; sound active mode, show mode, and DMX controlled. This
fixture is suitable for theaters, studios, retail stores, and other similar
locations. For best results use fog or special effects smoke to enhance
the beams projections.
Customer Support: ADJ Products, LLC provides a toll free cus-
tomer support line, to provide help and to answer any question should
you encounter problems during your set up or initial operation. You
may also visit us on the web at www.adj.com for any comments or
suggestions. Service Hours are Monday through Friday 8:00 a.m. to
4:30 p.m. Pacic Standard Time.
Voice: (800) 322-6337
Fax: (323) 582-2941
E-mail: support@americandj.com
Warning! To prevent or reduce the risk of electrical shock or re, do
not expose this unit to rain or moisture.
Warning! This may cause severe eye damage. Avoid looking directly
into the light source at all times!
To optimize the performance of this product, please read these
operating instructions carefully to familiarize yourself with the basic
operations of this unit. These instructions contain important safety
information regarding the use and maintenance of this unit. Please
keep this manual with the unit, for future reference.
Stinger Spot Features
• DMX-512 Protocol Compatible (9 DMX Channels or 11 Channels)
• 7 Colors + White
• Fixed Gobo Wheel with 7 Gobos + Spot
• 3 Operating Modes - Sound Active, Show Mode, & DMX Control
• Internal Microphone
• Digital Display for Address and Function Setting
• 4 Preprogrammed Shows
Stinger Spot Warranty Registration
The Stinger Spot carries a 2 year (730 days) limited warranty. Please
fill out the enclosed warranty card to validate your purchase and war-
ranty. You may also register your product online at www. adjproducts.
com. All returned service items whether under warranty or not, must
be freight pre-paid and accompany a return authorization (R.A.) number. If the unit is under warranty you must provide a copy of your
proof of purchase invoice. Please contact ADJ Products, LLC customer support for a R.A. number.
Stinger Spot Handling Precautions
Caution! There are no user serviceable parts inside this unit. Do not
attempt any repairs yourself, doing so will void your manufactures
warranty. In the unlikely event your unit may require service please
contact ADJ Products, LLC.
During operation the housing may become extremely hot. Avoid
touching the unit with bare hands while in use.
ADJ Products, LLC will not accept any liability for any resulting damages caused by the non-observance of this manual or any unauthor-
ized modication to this unit.
ADJ Products, LLC - www.adj.com - Stinger Spot Instruction Manual Page 3ADJ Products, LLC - www.adj.com - Stinger Spot Instruction Manual Page 2
Stinger Spot Safety Precautions
Stinger Spot Mounting
For Your Own Personal Safety, Please Read and Understand This
Manual Completely Before You Attempt To Install Or Operate
This Unit!
• To reduce the risk of electrical shock or re, do not expose this unit
rain or moisture
• Do not spill water or other liquids into or on to your unit.
• Be sure that the local power outlet match that of the required volt age for your unit.
• Do not attempt to operate this unit if the power cord has been
frayed or broken.
• Do not attempt to remove or break o the ground prong from
the electrical cord. This prong is used to reduce the risk of electrical
shock and re in case of an internal short.
• Disconnect from main power before making any type of connection.
• Do not remove the cover under any conditions. There are no user
serviceable parts inside.
• Never operate this unit when it’s cover is removed.
• Always be sure to mount this unit in an area that will allow proper
ventilation. Allow about 6” (15cm) between this device and a wall.
• Do not attempt to operate this unit, if it becomes damaged.
• This unit is intended for indoor use only, use of this product out doors voids all warranties.
• Always mount this unit in safe and stable matter.
• Power-supply cords should be routed so that they are not likely to
be walked on or pinched by items placed upon or against them,
paying particular attention to cords at plugs, convenience recep tacles, and the point where they exit from the appliance.
• Cleaning -The fixture should be cleaned only as recommended by
the manufacturer. See page 24 for cleaning details.
• Heat -This fixture should be situated away from heat sources such
as radiators, heat registers, stoves, or other appliances (including
amplifiers) that produce heat.
• The fixture should be serviced by qualified service personnel when:
A. Objects have fallen, or liquid has been spilled into the appliance.
B. The appliance has been exposed to rain or water.
C. The appliance does not appear to operate normally or exhibits
a marked change in performance.
When installing the unit, the trussing or area of installation must be
able to hold 10 times the weight without any deformation. When
installing the unit must be secured with a secondary safety attachment, e.g. and appropriate safety cable. Never stand directly below
the unit when mounting, removing, or servicing the unit.
Overhead mounting requires extensive experience, including calculating working load limits, installation material being used, and perodic
safety inspection of all installation material and unit. If you lack these
qualications, do not attempt the installation yourself.
The installaiton should be checked by a skilled person once a year.
The Stinger Spot is fully operational in three dierent mounting positions, hanging upside-down from a trussing setup, sideways from a
trussing setup, or set on a at level surface. To avoid internal damage
to the unit, never mount the unit on its side as illustrated above.
Be sure this xture is kept at least 0.5m away from any ammable
materials (decoration etc.). Always use and install the supplied safety
cable as a safety measure to prevent accidental damage and/or injury
in the event the clamp fails (see next page).
ADJ Products, LLC - www.adj.com - Stinger Spot Instruction Manual Page 5ADJ Products, LLC - www.adj.com - Stinger Spot Instruction Manual Page 4
Stinger Spot Mounting
Stinger Spot DMX Set Up
NOTICE: The suitable enviromental temperature for this light-
ing xture is between -25˚ C to 45˚ C. Do not place this lighting
xture in an enviroment where the temperatures are under or
above the temperatures stated above. This will allow the xture
to run at its best and help prolong the xture life.
Power Supply: The ADJ Stinger Spot contains a automatic voltage
switch, which will auto sense the voltage when it is plugged into the
power source. With this switch there is no need to worry about the correct power voltage, this unit can be plugged in anywhere.
DMX-512: DMX is short for Digital Multiplex. This is a universal pro-
tocol used by most lighting and controller manufactures as a form of
communication between intelligent fixtures and controllers. A DMX
controller sends DMX data instructions from the controller to the fixture. DMX data is sent as serial data that travels from fixture to fixture
via the DATA “IN” and DATA “OUT” XLR terminals located on all DMX
fixtures (most controllers only have a DATA “OUT” terminal).
DMX Linking: DMX is a language allowing all makes and models
of dierent manufactures to be linked together and operate from a
single controller, as long as all xtures and the controller are DMX
compliant. To ensure proper DMX data transmission, when using
several DMX fixtures try to use the shortest cable path possible. The
order in which fixtures are connected in a DMX line does not influence
the DMX addressing. For example; a fixture assigned a DMX address
of 1 may be placed anywhere in a DMX line, at the beginning, at the
end, or anywhere in the middle. Therefore, the first fixture controlled
by the controller could be the last fixture in the chain. When a fixture
is assigned a DMX address of 1, the DMX controller knows to send
DATA assigned to address 1 to that unit, no matter where it is located
in the DMX chain.
Screw one clamp via a M12 screw and nut to the included
bracket. Attach the bracket using the included screws to the
bottom of the Stinger Spot. Attach the eyehole screw to the
bottom of the base and pull the safety-cable through the screw
and over the trussing system or a safe xation spot. Insert the
end in the carabine and tighten the safety screw.
ADJ Products, LLC - www.adj.com - Stinger Spot Instruction Manual Page 6 ADJ Products, LLC - www.adj.com - Stinger Spot Instruction Manual Page 7
Data Cable (DMX Cable) Requirements (For DMX and Master/Slave
Operation): The Stinger Spot can be controlled via DMX-512 proto-
col. The Stinger Spot two DMX channel modes; 9 channel mode & 11
channel mode. The DMX address is set electronically using the controls on the front panel of the
unit. Your unit and your DMX controller require a
approved DMX-512 110 Ohm Data cable for data
input and data output (Figure 1). We recommend
Accu-Cable DMX cables. If you are making your
own cables, be sure to use standard 110-120 Ohm
shielded cable (This cable may be purchased at
almost all professional sound and lighting stores).
Figure 1
Stinger Spot DMX Set Up
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
DMX512
DMX+,DMX-,COMMON
1
2
3
Termination reduces signal errors and
avoids signal transmission problems
and interference. It is always advisable
to connect a DMX terminal, (Resistance
120 Ohm 1/4 W) between PIN 2 (DMX-)
and PIN 3 (DMX +) of the last fixture.
POWER
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
Stinger Spot DMX Set Up
Your cables should be made with a male and female XLR connector on
either end of the cable. Also remember that DMX cable must be daisy
chained and cannot be split.
Notice: Be sure to follow gures two and three when making your own
cables. Do not use the ground lug on the XLR connector. Do not connect the cable’s shield conductor to the ground lug or allow the shield
conductor to come in contact with the XLR’s outer casing. Grounding
the shield could cause a short circuit and erratic behavior.
COMMON
1
DMX512 IN
3
3-PIN XLR
2
Figure 2
XLR Pin Conguration
Pin 1 = Ground
Pin 2 = Data Compliment (negative)
Pin 3 = Data True (positive)
XLR Male Socket
1 Ground
Figure 3
DMX512 OT
3-PIN XLR
2 Cold
3 Hot
1
3
2
XLR Female Socket
2 Cold
DMX +
DMX -
1 Ground
3 Hot
5-Pin XLR DMX Connectors.
Some manufactures use 5-pin DMX-
512 data cables for DATA transmission in place of 3-pin. 5-pin DMX
xtures may be implemented in a 3-pin DMX line. When inserting standard 5-pin data cables in to a 3-pin line a cable adaptor must be used,
these adaptors are readily available at most electric stores. The chart
below details a proper cable conversion.
3-Pin XLR to 5-Pin XLR Conversion
Conductor 5-Pin XLR Male (In)3-Pin XLR Female (Out)
Ground/Shield
Data Compliment (- signal)
Data True (+ signal)
Not Used
Not Used
Pin 1
Pin 2
Pin 3
Pin 1
Pin 2
Pin 3
Pin 4 - Do Not Use
Pin 5 - Do Not Use
Special Note: Line Termination.
used, you may need to use a terminator on the last unit to avoid erratic
behavior. A terminator is a 110-120 ohm 1/4 watt resistor which is con-
When longer runs of cable are
nected between pins 2 and 3 of a male XLR connector (DATA + and
DATA -). This unit is inserted in the female XLR connector of the last
unit in your daisy chain to terminate the line. Using a cable terminator
(ADJ part number Z-DMX/T) will decrease the possibilities of erratic
behavior.
Termination reduces signal errors and
1
avoids signal transmission problems
3
and interference. It is always advisable
2
to connect a DMX terminal, (Resistance
120 Ohm 1/4 W) between PIN 2 (DMX-)
and PIN 3 (DMX +) of the last fixture.
Figure 4
ADJ Products, LLC - www.adj.com - Stinger Spot Instruction Manual Page 9ADJ Products, LLC - www.adj.com - Stinger Spot Instruction Manual Page 8
Stinger Spot System Menu
Stinger Spot System Menu
System Menu: When making adjustments press ENTER to
conrm your setup then press and hold the MENU button
for at least 3 seconds. To exit without making any adjust-
ments press the MENU button. The display will lock after 30
seconds, press the MENU button for 3 seconds to unlock.
ADDR - DMX Address Setting.
1. Press the either the MENU, UP, or DOWN buttons until “ADDR” is
displayed, press ENTER.
2. The current address will now be displayed and ashing. Press the
UP or DOWN buttons to nd your desired address. Press ENTER to
set your desired DMX address.
CHND - This will let select your desired DMX channel
mode.
1. Press the either the MENU button until “CHND” is displayed, press
ENTER. Either “9CH” or “11CH” will be displayed
2. Press the UP or DOWN buttons to nd your desired DMX channel
mode and press ENTER to conm and exit.
ADJ Products, LLC - www.adj.com - Stinger Spot Instruction Manual Page 10
SHND - Show modes 0-4 (Factory programs). Show
mode can run with or without sound active mode active.
1. Press the MENU button until “SHND” is displayed, press ENTER.
2. “Sh X” will now be displayed, “X” representing a number between
0-4. Shows 1-4 are factory programs, while show “0” is random mode.
Use the UP or DOWN buttons to nd your desired show.
3. When you have found your desired show press ENTER, then press
and hold the MENU button for at least 3 seconds to activate. After
you have set your desired show, it can be changed at any time using
the UP or DOWN buttons.
ADJ Products, LLC - www.adj.com - Stinger Spot Instruction Manual Page 11
Stinger Spot System Menu
Stinger Spot System Menu
DIND - This will let select your desired dimmer curve.
1. Press the either the MENU button until “DIND” is displayed, press
ENTER. 1 of 5 dimmer curves will be displayed. “STDA” (standard),
“STGE” (stage), “TV” (TV), “ARAL” (theatrical), or “THAL” (Architectural).
2. Press the UP or DOWN buttons to nd your desired dimmer curve
and press ENTER to conm and exit.
SLND - This will let you set unit as a master or slave in a
master/slave conguration.
1. Press the MENU button until “SLND” is displayed, press ENTER.
Either “MAST”, “SL 1”, or “SL 2” will be displayed.
2. Press the UP or DOWN buttons until your desired setting is displayed, press ENTER to conm.
NOTE: In a Master/Slave conguration you can set one xture to
Master and then set the next xture to “SL 2”, the xtures will now
have contrast movement to each other.
LOST - This mode can be used as a precaution mode, that
in case the DMX signal is lost, interrupted, or power is lost,
the operating mode chosen in the setup is the running mode
the xture will go into when the DMX signal is lost. You can
also set this as the operating mode you would like the unit to
return to when power is applied.
• SHND (Show Mode) - If the DMX signal is lost, interrupted, the unit
will automatically go into show mode.
• BLAC (Blackout) - If the DMX signal is lost or interrupted, the unit will
automatically go into stand by mode.
3. Press ENTER to conrm your desired set up.
SOUN - Sound Active mode.
1. Press the MENU button until “SOUN” is displayed, press ENTER.
2. The display will show either “ON” or “OFF”. Press the UP or
DOWN buttons to select “ON” to activate sound active mode, or
“OFF” to deactivate sound active mode.
3. Press ENTER to conrm.
SENS - In this mode you can adjust the sound sensitiv-
ity.
1. Press the MENU button until “SENS” is displayed, press ENTER.
2. A number between 0-100 will be displayed. Press the UP or DOWN
buttons to adjust the sound sensitivity. 0 being the least sensitive,
and 100 being the most sensitive.
3. When you have found your desired setting press ENTER to conrm.
PINT - Pan Inversion
1. Press the MENU button until “LOST” is displayed, and either
“HOLD”, “SHND”, or “BLAC” will be displayed beneath.
2. Press ENTER and the bottom choice will begin to ash. Use the UP
or DOWN buttons to choose an operating mode you would like the unit
to start up in when power is applied or the DMX signal is lost.
• Hold - If the DMX signal is lost the xture will stay in the last DMX setting. If power is applied and this mode is set, the unit will automatically
go into the last DMX set up.
ADJ Products, LLC - www.adj.com - Stinger Spot Instruction Manual Page 12 ADJ Products, LLC - www.adj.com - Stinger Spot Instruction Manual Page 13
1. Press the MENU button until “PINT” is displayed, press ENTER.
Either “Yes” or “No” will be displayed.
2. To activate the Pan inversion press the UP or DOWN buttons until
“Yes” is displayed, press ENTER to conm. To deactivate Pan inversion, select “No” and press Enter.
Stinger Spot System Menu
Stinger Spot System Menu
TINT - Tilt Inversion
1. Press the MENU button until “TINT” is displayed, press ENTER.
Either “Yes” or “No” will be displayed.
2. To activate the tilt inversion press the UP or DOWN buttons until
“Yes” is displayed, press ENTER to conm. To deactivate tilt inversion, select “No” and press Enter.
LED - With this function you can have the LED display
turn off after 10 seconds.
1. Press the MENU button until “LED” is displayed, press ENTER.
2. The display will show either “ON” or “OFF”. Press the UP or
DOWN buttons to select “ON” to keep the LED display on at all
times, or “OFF” to switch to have the LED display switch o after 10
seconds.
3. Press ENTER to conrm. To make you LED display reappear again
press any button.
DISP - This function will reverse the display 180º.
1. Press the MENU button until “DISP” is displayed, press ENTER.
2. Press ENTER to “ip” the display. Press ENTER to “ip” it again.
Press ENTER when you have made your desired setup.
RSET - Use this function to reset the unit.
1. Press the MENU button until “RSET” is displayed, press ENTER.
2. The xture will now reset.
Stinger Spot Home Adjustment Menu
To enter the home position adjustment menu, press the ENTER
button for at least 5 seconds. In this submenu you are able to adjust
the original position of the pan position, tilt position, color wheel position, and gobo wheel position.
OPAN - Adjustment of the pan position.
TEST - This function will run a self test program.
1. Press the MENU button until “TEST” is displayed, press ENTER.
2. The xture will now run a self test.
VER - Use this function to display the Software version of
the unit.
1. Press the either the MENU button until “VER” is displayed, press
ENTER.
2. The display will show the software version.
1. Press the ENTER button for at least 5 seconds, then press the UP
or DOWN buttons so that “OPAN” is displayed, press ENTER.
2. Use the UP and DOWN buttons to make your adjustments, and
then press ENTER to conrm. Press the MENU button for one second
to exit.
OTIL - Adjustment of the tilt position.
1. Press the ENTER button for at least 5 seconds, then press the UP
or DOWN buttons so that “OTIL” is displayed, press ENTER.
2. Use the UP and DOWN buttons to make your adjustments, and
then press ENTER to conrm. Press the MENU button for one second
to exit.
ADJ Products, LLC - www.adj.com - Stinger Spot Instruction Manual Page 15ADJ Products, LLC - www.adj.com - Stinger Spot Instruction Manual Page 14
Stinger Spot Operation Stinger Spot Home Adjustment Menu
OGOB - Adjustment of the gobo wheel.
1. Press the ENTER button for at least 5 seconds, then press the UP
or DOWN buttons so that “OGOB” is displayed, press ENTER.
2. Use the UP and DOWN buttons to make your adjustments, and
then press ENTER to conrm. Press the MENU button for one second
to exit.
OCOL - Adjustment for the color wheel.
1. Press the ENTER button for at least 3 seconds, then press the UP
or DOWN buttons so that “OCOL” is displayed, press ENTER.
2. Use the UP and DOWN buttons to make your adjustments, and
then press ENTER to conrm. Press the MENU button for one second
to exit.
Universal DMX Control: This function allows you to use a univer-
sal DMX-512 controller to control the chases and patterns, dimmer
and strobe. A DMX controller allows you to create unique programs
tailored to your individual needs.
1. The Stinger Spot has 2 DMX channel modes; 9 channel mode or
11 channel mode. See pages 19-22 for detailed description of the
DMX values and traits.
2. To control your fixture in DMX mode, follow the set-up procedures
on pages 5-7 as well as the set-up specifications that are includ ed with your DMX controller.
3. Use the controller’s faders to control the various DMX fixture traits.
4. This will allow you to create your own programs.
5. Follow the instruction on page 9 to set the DMX address.
6. For longer cable runs (more than a 100 feet) use a terminator on
the last fixture.
7. For help operating in DMX mode consult the manual included
with your DMX controller.
Sound Active Mode: This mode allows either single unit or several
units linked together, to run to the beat of the music.
1. Press the MENU button until “SOUN” is displayed, and press
ENTER. Press the UP or DOWN buttons so that “ON” is dis-
played and press ENTER.
2. Press the MENU button until “SENS” is displayed, and press
ENTER. Use the UP and DOWN buttons to adjust the sound
sensitivity. Press ENTER when you have found your desired sensi-
tivity level.
Show Mode: This mode allows either a single unit or several units
linked together, to run one of four shows that you choose.
1. Press the MENU button until “SHND” is displayed, and press
ENTER.
2. Press the UP or DOWN buttons until you nd your desired show,
and press ENTER.
ADJ Products, LLC - www.adj.com - Stinger Spot Instruction Manual Page 16 ADJ Products, LLC - www.adj.com - Stinger Spot Instruction Manual Page 17
Stinger Spot Master-Slave Set Up
Stinger Spot 9 Channel Mode
Master-Slave Operation This function will allow you to link up to 16
units together and operate without a controller. The units will be sound
activated. In Master-Slave operation one unit will act as the controlling
unit and the others will react to the controlling units programs. Any unit
can act as a Master or as a Slave.
1. Using approved DMX data cables, daisy chain your units togeth-
er via the XLR connector on the rear of the units. Remember the
Male XLR connector is the input and the Female XLR connector
is the output. The rst unit in the chain (master) will use the female
XLR connector only - The last unit in the chain will use the male
XLR connector only. For longer cable runs we suggest a termina tor at the last fixture.
2. On the Master unit press the MENU button until “SLND” is dis played, and press ENTER. Use the UP and DOWN buttons to
scroll to the “MAST” setting and press ENTER.
3. After setting the Master unit to the master setting find your
desired operating mode.
4. On the slave units press the MENU button until “SLND” is dis played, and press ENTER. Choose either “SL 1” or “SL 2” and
press ENTER. See page 10 for more info.
5. The slave units will now follow the Master unit.
Channel Value Function
1 0 - 255 PAN MOVEMENT 8bit
2 0 - 255 TILT MOVEMENT 8bit
3 COLORS
0 - 7 WHITE
8 - 14 RED
15 - 21 ORANGE
22 - 28 YELLOW
29 - 35 GREEN
36 - 42 BLUE
43 - 49 LIGHT BLUE
50 - 56 PINK
57 - 127 SPLIT COLORS
128 - 189 COLOR SCROLL FAST - SLOW
190 - 193 STOP
194 - 255 COLOR SCROLL SLOW - FAST
4 GOBO WHEEL
0 - 7 OPEN
8 - 15 GOBO 1
16 - 23 GOBO 2
24 - 31 GOBO 3
32 - 39 GOBO 4
40 - 47 GOBO 5
48 - 55 GOBO 6
56 - 63 GOBO 7
64 - 71 OPEN SHAKE
72 - 79 GOBO 1 SHAKE
80 - 87 GOBO 2 SHAKE
88 - 95 GOBO 3 SHAKE
96 - 103 GOBO 4 SHAKE
104 - 111 GOBO 5 SHAKE
112 - 119 GOBO 6 SHAKE
120 - 127 GOBO 7 SHAKE
128 - 189 GOBO SCROLL FAST - SLOW
190 - 193 STOP
194 - 255 GOBO SCROLL SLOW - FAST
ADJ Products, LLC - www.adj.com - Stinger Spot Instruction Manual Page 18
ADJ Products, LLC - www.adj.com - Stinger Spot Instruction Manual Page 19
Stinger Spot 9 Channel Mode
Stinger Spot 11 Channel Mode
Channel Value Function
5 SHUTTER/STROBE
0 - 7 BLACKOUT
8 - 15 SHUTTER OPEN
16 - 131 STROBING SLOW - FAST
132 - 139 SHUTTER OPEN
140 - 181 SHUTTER SLOW OPEN - FAST CLOSE
182 - 189 SHUTTER OPEN
190 - 231 SHUTTER FAST OPEN - SLOW CLOSE
232 - 239 SHUTTER OPEN
240 - 247 RANDOM STROBE
248 - 255 SHUTTER OPEN
6 0 - 255 DIMMER 0% - 100%
7 0 - 255 MOVEMENT SPEED FAST - SLOW
8 FUNCTION
0 - 69 NO FUNCTION
70 - 79 BLACKOUT WITH PAN/TILT
80 - 89 NO FUNCTION
90 - 99 BLACKOUT WITH COLOR CHANGE
100 - 109 NO FUNCTION
110 - 119 BLACKOUT WITH GOBO CHANGE
120 - 199 NO FUNCTION
200 - 209 RESET ALL
210 - 249 NO FUNCTION
250 - 255 SOUND ACTIVE MODE
9 DIMMER CURVES
0 - 20 STANDARD
21 - 40 STAGE
41 - 60 TV
61 - 80 ARCHITECTURAL
81 - 100 THEATER
101 - 255 DEFAULT TO UNIT CURVE SETTING
Channel Value Function
1 0 - 255 PAN MOVEMENT 8bit
2 0 - 255 PAN FINE 16bit
3 0 - 255 TILT MOVEMENT 8bit
4 0 - 255 TILT FINE 16bit
5 COLORS
0 - 7 WHITE
8 - 14 RED
15 - 21 ORANGE
22 - 28 YELLOW
29 - 35 GREEN
36 - 42 BLUE
43 - 49 LIGHT BLUE
50 - 56 PINK
57 - 127 SPLIT COLORS
128 - 189 COLOR SCROLL FAST - SLOW
190 - 193 STOP
194 - 255 COLOR SCROLL SLOW - FAST
6 GOBO WHEEL
0 - 7 OPEN
8 - 15 GOBO 1
16 - 23 GOBO 2
24 - 31 GOBO 3
32 - 39 GOBO 4
40 - 47 GOBO 5
48 - 55 GOBO 6
56 - 63 GOBO 7
64 - 71 OPEN SHAKE
72 - 79 GOBO 1 SHAKE
80 - 87 GOBO 2 SHAKE
88 - 95 GOBO 3 SHAKE
96 - 103 GOBO 4 SHAKE
104 - 111 GOBO 5 SHAKE
112 - 119 GOBO 6 SHAKE
120 - 127 GOBO 7 SHAKE
128 - 189 GOBO SCROLL FAST - SLOW
ADJ Products, LLC - www.adj.com - Stinger Spot Instruction Manual Page 20 ADJ Products, LLC - www.adj.com - Stinger Spot Instruction Manual Page 21
Stinger Spot 11 Channel Mode
Channel Value Function
6 190 - 193 STOP
194 - 255 GOBO SCROLL SLOW - FAST
7 SHUTTER/STROBE
0 - 7 BLACKOUT
8 - 15 SHUTTER OPEN
16 - 131 STROBING SLOW - FAST
132 - 139 SHUTTER OPEN
140 - 181 SHUTTER SLOW OPEN - FAST CLOSE
182 - 189 SHUTTER OPEN
190 - 231 SHUTTER FAST OPEN - SLOW CLOSE
232 - 239 SHUTTER OPEN
240 - 247 RANDOM STROBE
248 - 255 SHUTTER OPEN
8 0 - 255 DIMMER 0% - 100%
9 0 - 255 MOVEMENT SPEED FAST - SLOW
10 FUNCTION
1 - 69 NO FUNCTION
70 - 79 BLACKOUT WITH PAN/TILT
80 - 89 NO BLACKOUT WITH PAN/TILT
90 - 99 BLACKOUT WITH COLOR CHANGE
100 - 109 NO BLACKOUT WITH COLOR CHANGE
110 - 119 BLACKOUT WITH GOBO CHANGE
120 - 129 NO BLACKOUT WITH GOBO CHANGE
130 - 199 NO FUNCTION
200 - 209 RESET ALL
210 - 249 NO FUNCTION
250 - 255 SOUND ACTIVE MODE
11 DIMMER CURVES
0 - 20 STANDARD
21 - 40 STAGE
41 - 60 TV
61 - 80 ARCHITECTURAL
81 - 100 THEATER
101 - 255 DEFAULT TO UNIT CURVE SETTING
Stinger Spot Gobo Wheel
7
1
6
2
5
3
4
Stinger Spot CAD Drawing
173mm/6.81”
158mm/6.22”
147mm/5.78”
229mm/9”
236mm/9.29”
145mm/5.7”
ADJ Products, LLC - www.adj.com - Stinger Spot Instruction Manual Page 23ADJ Products, LLC - www.adj.com - Stinger Spot Instruction Manual Page 22
Stinger Spot Photometric Chart
R
G
B
1458 417
154
115
82
2790
780 356 207 143
425
123 58 36
28
RGBW
1m 2m 3m 4m 5m
4500
1280 584 339 227
1.0 2.0 3.0 4.0
Distance(m)
0
0m( )
5.0
60
0m( )
30900 10920 4916 2085
1788
17
1213
INNO POCKET SPOT
1.0 2.0 3.0 4.0
Distance(m)
0
0m( )
159000 75300 40060 19930
5.0
14470
6
6.0
9800
INNO BEAM LED
0m( )
6.0
Distance(m)
13
0
1.0 2.0 3.0 4.0
5.0
Stinger Spot Fuse Replacement
Locate and remove the unit’s power cord. Once the cord has been
removed located the fuse holder located inside the power socket.
Insert a flat-head screw driver into the power socket and gently pry
out the fuse holder. Remove the bad fuse and replace with a new one.
The fuse holder has a built-in socket for a spare fuse be sure not to
confuse the spare fuse with active fuse.
Stinger Spot Cleaning
Stinger Spot Dimmer Curve Chart
Ramp Effect
Standard
Stage
TV
Architectural
Theatre
(Fade Time) (Fade Time)
Due to fog residue, smoke, and dust cleaning the internal and external optical lenses and mirror should be carried out periodically to
optimize light output. Cleaning frequency depends on the environment in which the fixture operates (I.e. smoke, fog residue, dust,
dew). In heavy club use we recommend cleaning on a monthly basis.
Periodic cleaning will ensure longevity, and crisp output.
1. Use normal glass cleaner and a soft cloth to wipe down the out-
side casing.
2. Use a brush to wipe down the cooling vents and fan grill.
3. Clean the external optics with glass cleaner and a soft cloth every
20 days.
4. Clean the internal optics with glass cleaner and a soft cloth every
30-60 days.
5. Always be sure to dry all parts completely before plugging the unit
back in.
Stinger Spot Trouble Shooting
Trouble Shooting: Listed below are a few common problems that
you may encounter, with solutions.
No light output from the unit;
1. Be sure the external fuse has not blown. The fuse is located on
the rear panel of the unit.
2. Be sure the fuse holder is completely and properly seated.
Unit does not respond to sound;
1. Low frequencies (bass) should cause the unit to react to sound.
Tapping on the microphone, quiet or high pitched sounds may
ADJ Products, LLC - www.adj.com - Stinger Spot Instruction Manual Page 24 ADJ Products, LLC - www.adj.com - Stinger Spot Instruction Manual Page 25
not activate the unit.
Stinger Spot Warranty
MANUFACTURER’S LIMITED WARRANTY
A. ADJ Products, LLC hereby warrants, to the original purchaser, ADJ Products, LLC products
to be free of manufacturing defects in material and workmanship for a prescribed period from
the date of purchase (see specific warranty period on reverse). This warranty shall be valid only if the
product is purchased within the United States of America, including possessions and
territories. It is the owner ’s responsibility to establish the date and place of purchase by acceptable
evidence, at the time service is sought.
B. For warranty service you must obtain a Return Authorization number (RA#)
before sending back the product–please contact ADJ Products, LLC Service Department
at 800-322-6337. Send the product only to the ADJ Products, LLC factory. All
shipping charges must be pre-paid. If the requested repairs or service (including
parts replacement) are within the terms of this warranty, ADJ Products, LLC will pay return
shipping charges only to a designated point within the United States. If the entire instrument is
sent, it must be shipped in it’s original package. No accessories should be shipped with the product. If
any accessories are shipped with the product, ADJ Products, LLC shall have no liability whatsoever for
loss of or damage to any such accessories, nor for the safe return thereof.
C. This warranty is void if the serial number has been altered or removed; if the product is modified in any
manner which ADJ Products, LLC concludes, after inspection, affects the reliability of the product; if the
product has been repaired or serviced by anyone other than the ADJ Products, LLC factory unless prior
written authorization was issued to purchaser by ADJ Products, LLC; if the product is damaged because
not properly maintained as set forth in the instruction manual.
D. This is not a service contract, and this warranty does not include maintnance, cleaning or periodic check
up. During the period specified above, ADJ Products, LLC will replace defective parts at its expense
with new or refurbished parts, and will absorb all expenses for warranty service and repair labor by
reason of defects in material or workmanship. The sole responsibility of ADJ Products, LLC under this
warranty shall be limited to the repair of the product, or replacement thereof, including parts, at the sole
discretion of ADJ Products, LLC. All products covered by this warranty were manufactured after August
15, 2012, and bear indentifying marks to that effect.
E. ADJ Products, LLC reserves the right to make changes in design and/or improvements upon its products
without any obligation to include these changes in any products theretofore manufactured.
No warranty, whether expressed or implied, is given or made with respect to any accessory supplied with
products described above. Except to the extent prohibited by applicable law, all implied warranties made
by ADJ Products, LLC in connection with this product, including warranties of merchantability or fitness,
are limited in duration to the warranty period set forth above. And no warranties, whether expressed or
implied, including warranties of merchantability or fitness, shall apply to this product after said period
has expired. The consumer’s and/or Dealer’s sole remedy shall be such repair or replacement as is
expressly provided above; and under no circumstances shall ADJ Products, LLC be liable for any loss or
damage, direct or consequential, arising out of the use of, or inability to use, this product.
This warranty is the only written warranty applicable to ADJ Products, LLC Products and
supersedes all prior warranties and written descriptions of warranty terms and conditions heretofore
published.
MANUFACTURER’S LIMITED WARRANTY PERIODS:
•NonL.E.D.LightingProducts=1-year(365days)LimitedWarranty(Such as: Special Effect
Lighting, Intelligent Lighting, UV lighting, Strobes, Fog Machines, Bubble Machines, Mirror Balls, Par
Cans, Trussing, Lighting Stands etc. excluding LED and lamps)
•LaserProducts=1Year(365Days)LimitedWarranty(excluding laser diodes which have a 6 month
limited warranty)
•L.E.D.Products=2-year(730days)LimitedWarranty(excluding batteries which have a 180 day lim-
ited warranty). Note:2YearWarrantyonlyappliestopurchaseswithintheUnitedStates.
•StarTecSeries=1YearLimitedWarranty(excluding batteries which have a 180 day limited war-
ranty).
•ADJDMXControllers=2Year(730Days)LimitedWarranty
ADJ Products, LLC - www.adj.com - Stinger Spot Instruction Manual Page 26
Stinger Spot Specifications
Model: Stinger Spot
Voltage: 100 - 240V, 50/60Hz
LED: 1 x 10W White LED
Power Consumption: 36W
Dimensions: 6.75”(L) x 5.75”(W) x 10.75”(H)
174mm x 145mm x 273mm
Weight: 7 Lbs. / 3 kgs.
Beam Angle: 13 Degrees
Fuse: 2 Amp
Duty Cycle: None
DMX: 2 DMX Channel Modes: 9 Channel
Mode & 11 Channel Mode
Colors: 7 + White
Gobos: 7 + Spot
Sound Active: Ye s
Working Position: Any Safe, Secure Position
Warranty: 2 Year (730 days)
Please Note: Specications and improvements in the design
of this unit and this manual are subject to change without any
prior written notice.
Auto Sensing Voltage: This xture contains a automatic volt-
age switch, which will auto sense the voltage when it is plugged
into the power source.
ADJ Products, LLC
6122 S. Eastern Ave. Los Angeles, CA 90040 USA
Tel: 323-582-2650 / Fax: 323-725-6100
Web: www.adj.com / E-mail: info@americandj.com
A.D.J. Supply Europe B.V.
Junostraat 2
6468 EW Kerkrade
The Netherlands
service@adjgroup.eu / www.adj.eu
Tel: +31 45 546 85 00 / Fax: +31 45 546 85 99
Loading...