STINGER
©2015 ADJ Products, LLC all rights reserved. Information,
specications, diagrams, images, and instructions herein are
subject to change without notice. ADJ Products, LLC logo and
identifying product names and numbers herein are trademarks
of ADJ Products, LLC. Copyright protection claimed includes all
forms and matters of copyrightable materials and information
now allowed by statutory or judicial law or hereinafter granted.
Product names used in this document may be trademarks or
registered trademarks of their respective companies and are
hereby acknowledged. All non-ADJ Products, LLC brands and
product names are trademarks or registered trademarks of their
respective companies.
ADJ Products, LLC and all aliated companies hereby disclaim any and all liabilities for property, equipment, building,
and electrical damages, injuries to any persons, and direct or
indirect economic loss associated with the use or reliance of
any information contained within this document, and/or as a
result of the improper, unsafe, unsucient and negligent assembly, installation, rigging, and operation of this product.
Rev. 6/15
User Instructions
Europe Energy Saving Notice
Energy Saving Matters (EuP 2009/125/EC)
Saving electric energy is a key to help protecting the enviroment.
Please turn o all electrical products when they are not in use. To
avoid power consumption in idle mode, disconnect all electrical
equipment from power when not in use. Thank you!
Stinger General Information
Stinger General Instructions
Unpacking: Thank you for purchasing the Stinger by ADJ Products,
LLC. Every Stinger has been thoroughly tested and has been shipped
in perfect operating condition. Carefully check the shipping carton for
damage that may have occurred during shipping. If the carton appears
to be damaged, carefully inspect your xture for any damage and be
sure all equipment necessary to operate the unit has arrived intact. In
the event damage has been found or parts are missing, please contact
our toll free customer support number for further instructions. Please
do not return this unit to your dealer without contacting customer support rst.
Introduction: The Stinger is a 10 channel, DMX intelligent LED moon-
flower, strobe, & laser fixture. The fixture can operate in as a stand
alone fixture or in a Master/Slave configuration. The Stinger has two
operating modes; sound active and DMX Control. For best results use
fog or special effects smoke to enhance the beams projections.
Customer Support: ADJ Products, LLC provides a toll free cus-
tomer support line, to provide help and to answer any question should
you encounter problems during your set up or initial operation. You
may also visit us on the web at www.adj.com for any comments or
suggestions. Service Hours are Monday through Friday 8:00 a.m. to
4:30 p.m. Pacic Standard Time.
Voice: (800) 322-6337
Fax: (323) 582-2941
E-mail: support@adj.com
Warning! To prevent or reduce the risk of electrical shock or re, do
not expose this unit to rain or moisture.
Caution! This may cause eye damage. Avoid looking directly into the
light source. Use sensible precaution.
To optimize the performance of this product, please read these
operating instructions carefully to familiarize yourself with the basic
operations of this unit. These instructions contain important safety
information regarding the use and maintenance of this unit. Please
keep this manual with the unit, for future reference.
Stinger Features
• DMX-512 Protocol Compatible (10 DMX Channels)
• RGBWAP Hex LED’s
• Green & Red Lasers
• 3 Operating Modes - Sound Active, Auto Run, & DMX Control
• Internal Microphone
• Digital Display for Address and Function Setting
• Power Cord Daisy Chain
Stinger Warranty Registration
The Stinger carries a 1 Year limited warranty. Please fill out the
enclosed warranty card to validate your purchase and warranty. You
may also register your product online at www. americandj.com. All
returned service items whether under warranty or not, must be freight
pre-paid and accompany a return authorization (R.A.) number. If the
unit is under warranty you must provide a copy of your proof of purchase invoice. Please contact ADJ customer support for a R.A. number.
Stinger Handling Precautions
Caution! There are no user serviceable parts inside this unit. Do not
attempt any repairs yourself, doing so will void your manufactures
warranty. In the unlikely event your unit may require service please
contact ADJ Products, LLC.
ADJ Products, LLC - www.adj.com - Stinger Instruction Manual Page 2
During operation the housing may become extremely hot. Avoid
touching the unit with bare hands while in use.
ADJ Products, LLC will not accept any liability for any resulting damages caused by the non-observance of this manual or any unauthor-
ized modication to this unit.
ADJ Products, LLC - www.adj.com - Stinger Instruction Manual Page 3
!
!
Stinger Safety Precautions
LASER RADIATION AVOID
DIRECT EYE EXPOSURE
Maximum output <5 mW
Wavelength: 405, 532nm
This device complies with 21 CFR chapter I,
Subchapter J, or CFR 1040.10 and 1040.11
Safety Issues: This unit may “pop” the fuse if the maximum allotted
load of 2 amps is reached.
• To reduce the risk of electrical shock or re, do not expose this unit
rain or moisture.
• Do not spill water or other liquids into or on to your unit.
• Do not attempt to remove or break o the ground prong from the
electrical cord. This prong is used to reduce the risk of electrical
shock and re in case of an internal short. Do not attempt to oper ate this unit if the power cord has been frayed or broken.
• Disconnect from main power before making any type of connection.
• Do not remove the cover under any conditions. There are no user
serviceable parts inside.
• Always be sure to mount this unit in an area that will allow proper
ventilation. Allow about 6” (15cm) between this device and a wall.
• Do not attempt to operate this unit, if it becomes damaged.
• This unit is intended for indoor use only, use of this product out doors voids all warranties.
• During long periods of non-use, disconnect the unit’s main power.
• Always mount this unit in safe and stable matter.
• Power cords should be routed so they are not likely to be walked
on, pinched by items placed upon or against them.
• Cleaning -The fixture should be cleaned only as recommended by
the manufacturer. See page 17 for cleaning details.
• Heat -The appliance should be situated away from heat sources
such as radiators, heat registers, stoves, or other appliances
(including amplifiers) that produce heat.
• The fixture should be serviced by qualified service personnel when:
A. The power-supply cord or the plug has been damaged.
B. Objects have fallen, or liquid has been spilled into the unit.
C. The unit has been exposed to rain or water.
D. The unit does not appear to operate normally or exhibits a
marked change in performance.
Class IIIa laser product
Stinger Laser Warnings and Safety
NON-INTERLOCKED HOUSING WARNING
The Royal Sky contains high power laser devices internally. Do not
open the laser housing, due to the potential exposure to unsafe levels
of laser radiation. The laser power levels, if the unit is opened, can
cause instant blindness, skin burns and res.
STOP AND READ ALL LASER SAFETY DATA
OPERATION INSTRUCTIONS AND LASER SAFETY
The light source emitted from this product can potentially cause eye
injury if not set up and used properly. The light source emitted from a
laser is very dierent from any other light sources with which you may
be aware of. Laser light is thousands of times more concentrated
than any light from any other kind of light source. This concentration
of light can cause instant eye injuries, primarily by burning the retina
(the back of your eyeball contatining cells that are sensitive to light).
Even if you cannot feel “heat” from a laser beam, it can still potentially injure or blind you or your audience. Even very small amounts
of laser beam light are potentially hazardous even at long distances.
Laser eye injuries can be sustained faster than you can blink.
Do not think that because this laser splits the laser beam into hundreds of beams and that the laser beam is scanned out in high
speed, that an individual laser beam is safe for eye exposure. This
laser uses dozens of milliwatts of laser power (Class 3B levels internally) before it splits into multiple beams (Class 3R levels). Many of
the individual beams are potentially hazardous to the eyes.
Do not that because the laser light is moving, it is safe. This is not
true. Nor, do the laser beams always move. Since eye injuries can
occur instantly, it is critical to prevent even the smallest possibility of
any direct eye exposure. In the laser safety regulation, it is not legal
to aim Class 3R lasers in areas which people can get exposed. This
is true even if it is aimed below people’s faces, such as on a dance
oor.
Do not operate the laser without rst reading and understanding
all safety and technical data in this manual.
Always set up and install all laser eects so that all laser light is at
least 3 meters (9.8 feet) above the oor on which people can stand.
ADJ Products, LLC - www.adj.com - Stinger Instruction Manual Page 5ADJ Products, LLC - www.adj.com - Stinger Instruction Manual Page 4
Stinger Laser Warnings and Safety
Stinger Set Up
After setting up, and before public use, test laser to ensure proper
function. Do not use if any defect is detected. Do not use if laser
emits only one or two laser beams rather than dozens/hundreds, as
this could indicate damage to the diraction grating optic, and could
allow emission of higher laser levels above Class 3R.
Do not point lasers at people or animals. Never look into the laser
aperture or laser beams.
Do not point lasers in areas in which people can potentially get
exposed, such as uncontrolled balconies, etc.
Do not point lasers at highly reective surfaces, such as windows,
mirrors and shiny metal. Even laser reections can be hazardous.
Never point a laser at aircraft, this is a federal oense.
Never point un-terminated laser beams into the sky.
Do not expose the output optic (aperture) to cleaning chemicals.
Do not use laser if the laser appears to be emitting only one or two
beams.
Do not use the laser if the housing is damaged, the housing is open,
or if the optics appear damaged in any way.
Never open the laser housing. The high laser power levels inside of
the protective housing can start res, burn skin and will cause instant
eye injury.
Never leave this device running unattended.
The operation of a class 3R laser show is only allowed if the show
is controlled by a skilled and well- trained operator, familiar with the
data included in this manual.
The legal requirements for using laser entertainment products vary
from country to country. The user is responsible for the legal requirements at the location/country of use.
Always use proper lighting safety cables when hanging lights and
eects overhead.
Power Supply: The ADJ Stinger contains a automatic voltage switch,
which will auto sense the voltage when it is plugged into the power
source. With this switch there is no need to worry about the correct
power voltage, this unit can be plugged in anywhere.
DMX-512: DMX is short for Digital Multiplex. This is a universal pro-
tocol used by most lighting and controller manufactures as a form of
communication between intelligent fixtures and controllers. A DMX
controller sends DMX data instructions from the controller to the fixture. DMX data is sent as serial data that travels from fixture to fixture
via the DATA “IN” and DATA “OUT” XLR terminals located on all DMX
fixtures (most controllers only have a DATA “OUT” terminal).
DMX Linking: DMX is a language allowing all makes and models of
dierent manufactures to be linked together and operate from a single controller, as long as all xtures and the controller are DMX compliant. To ensure proper DMX data transmission, when using several
DMX fixtures try to use the shortest cable path possible. The order
in which fixtures are connected in a DMX line does not influence the
DMX addressing. For example; a fixture assigned a DMX address of 1
may be placed anywhere in a DMX line, at the beginning, at the end,
or anywhere in the middle. When a fixture is assigned a DMX address
of 1, the DMX controller knows to send DATA assigned to address 1
to that unit, no matter where it is located in the DMX chain.
Data Cable (DMX Cable) Requirements (For DMX and Master/Slave
Operation): The Stinger can be controlled via DMX-512 protocol. The
Stinger is a 10 channel DMX unit. The DMX address is set electronically using the controls on the back panel of the unit. Your unit and
your DMX controller require a approved DMX-512 110 Ohm Data cable
for data input and data output (Figure 1). We recommend Accu-Cable
DMX cables. If you are making your own cables, be
sure to use standard 110-120 Ohm shielded cable
(This cable may be purchased at almost all professional sound and lighting stores). Your cables
should be made with a male and female XLR connector on either end of the cable. Also remember
that DMX cable must be daisy chained and cannot
be split.
Figure 1
ADJ Products, LLC - www.adj.com - Stinger Instruction Manual Page 6 ADJ Products, LLC - www.adj.com - Stinger Instruction Manual Page 7
Stinger Set Up
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
DMX512
DMX+,DMX-,COMMON
1
2
3
Termination reduces signal errors and
avoids signal transmission problems
and interference. It is always advisable
to connect a DMX terminal, (Resistance
120 Ohm 1/4 W) between PIN 2 (DMX-)
and PIN 3 (DMX +) of the last fixture.
POWER
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
Stinger Set Up
Notice: Be sure to follow gures two and three when making your own
cables. Do not use the ground lug on the XLR connector. Do not connect the cable’s shield conductor to the ground lug or allow the shield
conductor to come in contact with the XLR’s outer casing. Grounding
the shield could cause a short circuit and erratic behavior.
COMMON
1
DMX512 IN
3
3-PIN XLR
2
Figure 2
XLR Pin Conguration
Pin 1 = Ground
Pin 2 = Data Compliment (negative)
Pin 3 = Data True (positive)
Figure 4
XLR Male Socket
1 Ground
DMX512 OUT
3-PIN XLR
2 Cold
3 Hot
1
3
2
XLR Female Socket
2 Cold
DMX +
DMX -
1 Ground
3 Hot
Figure 3
Special Note: Line Termination.
When longer runs of cable are
used, you may need to use a terminator on the last unit to avoid erratic
behavior. A terminator is a 110-120 ohm 1/4 watt resistor which is connected between pins 2 and 3 of a male XLR connector (DATA + and
DATA -). This unit is inserted in the female XLR connector of the last
unit in your daisy chain to terminate the line. Using a cable terminator
(ADJ part number Z-DMX/T) will decrease the possibilities of erratic
behavior.
Termination reduces signal errors and
1
avoids signal transmission problems
3
and interference. It is always advisable
2
to connect a DMX terminal, (Resistance
120 Ohm 1/4 W) between PIN 2 (DMX-)
and PIN 3 (DMX +) of the last fixture.
5-Pin XLR DMX Connectors.
Some manufactures use 5-pin XLR
connectors for DATA transmission in place of 3-pin. 5-pin XLR xtures
may be implemented in a 3-pin XLR DMX line. When inserting standard 5-pin XLR connectors in to a 3-pin line a cable adaptor must be
used, these adaptors are readily available at most electric stores. The
chart below details a proper cable conversion.
3-Pin XLR to 5-Pin XLR Conversion
Conductor 5-Pin XLR Male (In)3-Pin XLR Female (Out)
Ground/Shield
Data Compliment (- signal)
Data True (+ signal)
Not Used
Not Used
Pin 1
Pin 2
Pin 3
Pin 1
Pin 2
Pin 3
Pin 4 - Do Not Use
Pin 5 - Do Not Use
Stinger Installation
The unit should be mounted using a mounting clamp (not provided),
axing it to the mounting bracket that is provided with the unit.
Always ensure that the unit is rmly xed to avoid vibration and slipping while operating. Always ensure that the structure to which you
are attaching the unit is secure and is able to support a weight of 10
times the unit’s weight. Also, always use a safety cable that can hold
12 times the weight of the unit when installing the xture.
The equipment must be installed by a professional, and it must be
installed in a place where it is out of the reach of people’s grasp.
ADJ Products, LLC - www.adj.com - Stinger Instruction Manual Page 9ADJ Products, LLC - www.adj.com - Stinger Instruction Manual Page 8
Stinger Laser Warning Labels
Stinger System Menu
NO MENU FUNCTION
1 Addr Address setting, press DOWN/UP to choose 1-512
Sh_1
Led show only
Sh_2 Strobe show only
Sh_3 Laser show only
2
3 Sens 0-99 sound sensitivity from low to high
4 Soun
5 Vers Ve1.0 software version
Sh_4 Led + Laser mixed show
Sh_5 Led + Strobe mixed show
Sh_6 Laser + Strobe mixed show
Sh_7 Led + Strobe + Laser mixed show
ON Sound mode ON，run Sound mode
OFF Sound mode OFF，run auto mode
ADJ Products, LLC - www.adj.com - Stinger Instruction Manual Page 10
ADJ Products, LLC - www.adj.com - Stinger Instruction Manual Page 11
Stinger System Menu
Stinger Operation
LCD DISPLAY LOCK:
The display will lock after 30 seconds. Press and hold the MENU
button for at least 10 seconds to unlock the display and access the
menu.
ADDR - DMX Address Setting.
1. Press the either the MENU button until “ADDR” is displayed, press
ENTER.
2. The current DMX address will now be displayed. Press the UP or
DOWN buttons to nd your desired address. Press ENTER to set
your desired DMX address.
SHOW - Show mode. There are 7 show modes to
choose from.
1. Press the MENU button until “Show” is displayed, press ENTER.
2. The display will show one of seven auto show modes. Use the UP
or DOWN buttons to nd your desired show and press ENTER to
activate. See the system menu on page 11 for the dierent shows.
SOUN - Sound Active mode with adjustable sound sen-
sitivity.
1. Press the MENU button until “Soun” is displayed, press ENTER.
2. Use the UP or DOWN buttons to either turn sound activity “On” or
“O”, and press ENTER.
3. Press the MENU button until “Sens” is displayed, and press
ENTER. Use the UP or DOWN buttons to adjust the sound sensitivity.
VER - Use this function to display the Software version of
the unit.
Universal DMX Control: This function allows you to use a univer-
sal DMX-512 controller to control the patterns, rotation and strobing.
A DMX controller allows you to create unique programs tailored to
your individual needs.
1. The Stinger is a 10 DMX channel DMX fixture. See pages 15-16
for detailed description of the DMX values and traits.
2. To control your fixture in DMX mode, follow the set-up procedures
on pages 7-9 as well as the set-up specifications that are
included with your DMX controller.
3. Follow the instructions on page 12 to set the DMX address.
4. For longer cable runs (more than a 100 feet) use a terminator on
the last fixture.
5. For help operating in DMX mode consult the manual included
with your DMX controller.
Sound Active Mode: This mode allows a single unit or several units
linked together, to run to the beat of the music.
1. Press the MENU button until “Soun” is displayed, and press
ENTER.
2. Press the UP or DOWN buttons to either activate sound active
mode or deactivate, and press ENTER. The unit will now run to
the beat of the music.
3. The sound sensitivity can be adjusted by pressing the MENU
button until “Sens” is displayed, and then press ENTER. Use the
UP or DOWN buttons to adjust the sound sensitivity, 0 being the
least sensitive, and 99 being the most sensitive.
Show Mode: This mode allows a single unit or several units linked
together, to run to a built-in program.
1. Press the MENU button until “Show” is displayed, and press
ENTER.
2. Press the UP or DOWN buttons to nd your desired show and
press ENTER. The unit will now run your chosen built-in program.
1. Press the either the MENU button until “VER” is displayed, press
ENTER.
2. The display will show the software version.
ADJ Products, LLC - www.adj.com - Stinger Instruction Manual Page 12 ADJ Products, LLC - www.adj.com - Stinger Instruction Manual Page 13
Stinger
Master-Slave Set Up
Stinger DMX Traits
Master-Slave Set Up: This function will allow you to link up to 16
units together and operate without a controller. In a Master-Slave
set-up one unit will act as the controlling unit and the others will react
to the controlling units programs. Any unit can act as a Master or as a
Slave.
1. Using standard XLR microphone cables, daisy chain your units
together via the XLR connector on the rear of the units. Remem ber the Male XLR connector is the input and the Female XLR
connector is the output. The rst unit in the chain (master) will use
the female XLR connector only - The last unit in the chain will use
the male XLR connector only. For longer cable runs we suggest a
terminator at the last fixture.
2. Set the Master to your desired operating mode.
3. Set the Slave unit(s) to address “001”.
4. The slave unit(s) will now follow the Master unit.
Stinger Power Cord Daisy Chain
With this feature you can connect the xtures to one another
using the IEC input and output sockets. The quantity that can be
connected is 10 xtures maximum. After 10 xtures you will need
to use a new power outlet. They must be the same xtures. DO
NOT mix xtures.
Channel Value Function
1 AUTO RUN/SOUND ACTIVE
0 - 9 BLACKOUT
10 - 39 SIX COLORS LED AUTO RUN
40 - 69 WHITE LEDS AUTO RUN
70 - 99 LASER AUTO RUN
100 - 129 AUTO RUN MIXING
130 - 159 SIX COLORS & STROBING
160 - 189 LASER & STROBING
190 - 219 LEDS, LASER, & STROBING
220 - 255 DMX MODE
2 RGBWAP
0 - 9 BLACKOUT
10 - 198 COLOR MACROS
199 - 225 COLOR CHASE 1
226 - 255 COLOR CHASE 2
3 AUTO RUN
0 - 255 AUTO RUN SPEED SLOW - FAST
4 LED STROBE
0 - 9 NO STROBE
10 - 244 LED STROBE SLOW - FAST
245 - 255 SOUND ACTIVE STROBING
5 WHITE LEDS
0 - 9 BLACKOUT
10 - 135 WHITE OUTPUT POSITION
136 - 255 WHITE OUTPUT CHASE
6 WHITE LED STROBE
0 - 127 CHASE SLOW - FAST (NO STROBE)
128 - 255 CHASE SLOW - FAST (STROBING)
7 LASERS
0 - 9 BLACKOUT
10 - 49 RED LASER
50 - 89 GREEN LASER
90 - 129 RED & GREEN LASERS
ADJ Products, LLC - www.adj.com - Stinger Instruction Manual Page 14 ADJ Products, LLC - www.adj.com - Stinger Instruction Manual Page 15
Stinger DMX Traits
Stinger Fuse Replacement
Channel Value Function
7 LASERS
130 - 169 RED & GREEN LASERS FLICKER
170 - 209 GREEN & RED LASERS FLICKER
210 - 249 RED & GREEN LASERS FLICKER
SYNC
250 - 255 RED & GREEN LASERS ALTERNATE
FLICKER
8 LASER STROBE CONTROL
0 - 9 NO STROBE
10 - 244 STROBING SLOW - FAST
245 - 255 SOUND ACTIVE STROBING
9 LED ROTATION
0 - 8 NO ROTATION
9 - 127 CLOCKWISE ROTATION
SLOW - FAST
128 - 255 COUNTER-CLOCKWISE ROTATION
SLOW - FAST
10 LASER ROTATION
0 - 127 LASER PATTERNS
128 - 255 PATTERN CHASE SLOW - FAST
Disconnect the unit from its power source. Remove the power cord
from the unit. Once the cord has been removed, you will find that
the fuse holder is located inside the power socket. Insert a flat-head
screw driver into the power socket and gently pry out the fuse holder.
Remove the bad fuse and replace with a new one. The fuse holder also
has a holder for a spare fuse.
Stinger Cleaning
Fixture Cleaning: Due to fog residue, smoke, and dust cleaning the
internal and external optical lenses and mirror should be carried out
periodically to optimize light output. Cleaning frequency depends on
the environment in which the fixture operates (I.e. smoke, fog residue,
dust, dew). In heavy club use we recommend cleaning on a monthly
basis. Periodic cleaning will ensure longevity, and crisp output.
1. Use normal glass cleaner and a soft cloth to wipe down the out-
side casing.
2. Use a brush to wipe down the cooling vents and fan grill.
3. Clean the external optics and mirror with glass cleaner and a soft
cloth every 20 days.
4. Clean the internal optics with glass cleaner and a soft cloth every
30-60 days.
5. Always be sure to dry all parts completely before plugging the unit
back in.
Stinger Trouble Shooting
Trouble Shooting: Listed below are a few common problems that
you may encounter, with solutions.
No light output from the unit;
1. Be sure the external fuse has not blown. The fuse is located on
the rear panel of the unit.
2. Be sure the fuse holder is completely and properly seated.
Unit does not respond to sound;
1. Low frequencies (bass) should cause the unit to react to sound.
Tapping on the microphone, quiet or high pitched sounds may
not activate the unit.
2. Check the sound sensitivity level.
ADJ Products, LLC - www.adj.com - Stinger Instruction Manual Page 16 ADJ Products, LLC - www.adj.com - Stinger Instruction Manual Page 17
Stinger Warranty
MANUFACTURER’S LIMITED WARRANTY
A. ADJ Products, LLC hereby warrants, to the original purchaser, ADJ Products, LLC products
to be free of manufacturing defects in material and workmanship for a prescribed period from
the date of purchase (see specific warranty period on reverse). This warranty shall be valid only if the
product is purchased within the United States of America, including possessions and
territories. It is the owner ’s responsibility to establish the date and place of purchase by acceptable
evidence, at the time service is sought.
B. For warranty service you must obtain a Return Authorization number (RA#)
before sending back the product–please contact ADJ Products, LLC Service Department
at 800-322-6337. Send the product only to the ADJ Products, LLC factory. All
shipping charges must be pre-paid. If the requested repairs or service (including
parts replacement) are within the terms of this warranty, ADJ Products, LLC will pay return
shipping charges only to a designated point within the United States. If the entire instrument is
sent, it must be shipped in it’s original package. No accessories should be shipped with the product. If
any accessories are shipped with the product, ADJ Products, LLC shall have no liability whatsoever for
loss of or damage to any such accessories, nor for the safe return thereof.
C. This warranty is void if the serial number has been altered or removed; if the product is modified in any
manner which ADJ Products, LLC concludes, after inspection, affects the reliability of the product; if the
product has been repaired or serviced by anyone other than the ADJ Products, LLC factory unless prior
written authorization was issued to purchaser by ADJ Products, LLC; if the product is damaged because
not properly maintained as set forth in the instruction manual.
D. This is not a service contract, and this warranty does not include maintnance, cleaning or periodic check
up. During the period specified above, ADJ Products, LLC will replace defective parts at its expense
with new or refurbished parts, and will absorb all expenses for warranty service and repair labor by
reason of defects in material or workmanship. The sole responsibility of ADJ Products, LLC under this
warranty shall be limited to the repair of the product, or replacement thereof, including parts, at the sole
discretion of ADJ Products, LLC. All products covered by this warranty were manufactured after August
15, 2012, and bear indentifying marks to that effect.
E. ADJ Products, LLC reserves the right to make changes in design and/or improvements upon its products
without any obligation to include these changes in any products theretofore manufactured.
No warranty, whether expressed or implied, is given or made with respect to any accessory supplied with
products described above. Except to the extent prohibited by applicable law, all implied warranties made
by ADJ Products, LLC in connection with this product, including warranties of merchantability or fitness,
are limited in duration to the warranty period set forth above. And no warranties, whether expressed or
implied, including warranties of merchantability or fitness, shall apply to this product after said period
has expired. The consumer’s and/or Dealer’s sole remedy shall be such repair or replacement as is
expressly provided above; and under no circumstances shall ADJ Products, LLC be liable for any loss or
damage, direct or consequential, arising out of the use of, or inability to use, this product.
This warranty is the only written warranty applicable to ADJ Products, LLC Products and
supersedes all prior warranties and written descriptions of warranty terms and conditions heretofore
published.
MANUFACTURER’S LIMITED WARRANTY PERIODS:
•LightingProducts=1-year(365days)LimitedWarranty(Such as: Special Effect Lighting, Intelligent
Lighting, UV lighting, Strobes, Fog Machines, Bubble Machines, Mirror Balls, Par Cans, Trussing,
Lighting Stands etc. excluding LED and lamps)
•LaserProducts=1Year(365Days)LimitedWarranty(excluding laser diodes which have a 6 month
limited warranty)
•L.E.D.Products=2-year(730days)LimitedWarranty(excluding motors, PCB boards, and power
supplies, which have a 1-year (365 day Limited Warranty) batteries which have a 180 day limited war-
ranty). Only the L.E.D.s carry a 2-year warranty (excludingStarTecSerieswhichacarriesa1Year
LimitedWarranty)
•ADJDMXControllers=2Year(730Days)LimitedWarranty(excluding faders and tact switches)
ADJ Products, LLC - www.adj.com - Stinger Instruction Manual Page 18
Stinger Specifications
Model: Stinger
Voltage: 100V ~ 240V 50/60Hz
LED: 6 x 5W RGBAWP Hex LEDs
8 x 3W White LEDs
Laser: 4.9mW Red & Green Laser Diodes
Power Draw: 70W
Fuse: 2A
Power Cord Daisy Chain: 10 Fixtures Max.
Dimensions: 12”(L) x 9”(W) x 9.75”(H)
304mm x 230.5mm x9.75mm
Weight: 11 lbs. / 5 kgs.
Colors: RGBAWP
Duty Cycle: None
DMX Channels: 10
Sound Active: Ye s
Working Position: Any Safe, Secure Position
Warranty: 1 Year (365 Days)
Auto Sensing Voltage: This xture contains a automatic voltage
switch, which will auto sense the voltage when it is plugged into
the power source.
Please Note: Specications and improvements in the design
of this unit and this manual are subject to change without any
prior written notice.
ADJ Products, LLC
6122 S. Eastern Ave. Los Angeles, CA 90040 USA
Tel: 323-582-2650 / Fax: 323-725-6100
Web: www.adj.com / E-mail: info@americandj.com
A.D.J. Supply Europe B.V.
Junostraat 2
6468 EW Kerkrade
Netherlands
service@adjgroup.eu / www.adj.com
Tel: +31 45 546 85 00 / Fax: +31 45 546 85 99
Loading...