ADJ Saber Spot WW Users Manual

Saber Spot WW

©2017 ADJ Products, LLC all rights reserved. Information,

specications, diagrams, images, and instructions herein are
subject to change without notice. ADJ Products, LLC logo and
identifying product names and numbers herein are trademarks
of ADJ Products, LLC. Copyright protection claimed includes all
forms and matters of copyrightable materials and information
now allowed by statutory or judicial law or hereinafter granted.
Product names used in this document may be trademarks or
registered trademarks of their respective companies and are
hereby acknowledged. All non-ADJ Products, LLC brands and
product names are trademarks or registered trademarks of their

respective companies.

ADJ Products, LLC and all aliated companies hereby dis­claim any and all liabilities for property, equipment, building,
and electrical damages, injuries to any persons, and direct or
indirect economic loss associated with the use or reliance of
any information contained within this document, and/or as a
result of the improper, unsafe, unsucient and negligent as­sembly, installation, rigging, and operation of this product.

2/17

User Instructions

Europe Energy Saving Notice
Energy Saving Matters (EuP 2009/125/EC)
Saving electric energy is a key to help protecting the enviroment.
Please turn o all electrical products when they are not in use. To
avoid power consumption in idle mode, disconnect all electrical
equipment from power when not in use. Thank you!

Saber Spot WW General Information

Saber Spot WW General Instructions

Unpacking: Thank you for purchasing the Saber Spot WW by ADJ

Products, LLC. Every Saber Spot WW has been thoroughly tested and
has been shipped in perfect operating condition. Carefully check the
shipping carton for damage that may have occurred during shipping.
If the carton appears to be damaged, carefully inspect your xture for
any damage and be sure all equipment necessary to operate the unit
has arrived intact. In the event damage has been found or parts are
missing, please contact our toll free customer support number for fur­ther instructions. Please do not return this unit to your dealer without
contacting customer support rst.

Introduction: The Saber Spot WW is a DMX intelligent LED fix-

ture. The Saber Spot WW can operate as a stand alone fixture or in a
Master/Slave set up. The Saber Spot WW has three operating modes;
WW dimmer mode, show mode, & DMX controlled. This fixture is suit-
able for theaters, studios, retail stores, and other similar locations. For

best results use fog or special effects smoke to enhance the beams
projections.

Customer Support: ADJ Products, LLC provides a toll free cus-

tomer support line, to provide help and to answer any question should
you encounter problems during your set up or initial operation. You
may also visit us on the web at www.adj.com for any comments or
suggestions. Service Hours are Monday through Friday 8:00 a.m. to
4:30 p.m. Pacic Standard Time.
Voice: [phone]
Fax: [phone]
E-mail: [e-mail]

Warning! To prevent or reduce the risk of electrical shock or re, do

not expose this unit to rain or moisture.

Warning! This may cause severe eye damage. Avoid looking directly

into the light source at all times!

To optimize the performance of this product, please read these
operating instructions carefully to familiarize yourself with the basic
operations of this unit. These instructions contain important safety
information regarding the use and maintenance of this unit. Please
keep this manual with the unit, for future reference.

Saber Spot WW Features

• DMX-512 Protocol Compatible (3 DMX Channel Modes: 1/2/4

• 3 Operating Modes - Show Mode, WW Dimmer Mode & DMX
Control

• 5 Dimmer Curves (Standard, Stage, TV, Architectural, & Theatre)

• Digital Display for Address and Function Setting

• UC IR Compatible (Not Included) & Airstream App Compatible

• Power Cord Daisy Chainable (See page 23)

Saber Spot WW Warranty Registration

The Saber Spot WW carries a 2 year (730 days) limited warranty.
Please fill out the enclosed warranty card to validate your purchase
and warranty. You may also register your product online at www. adj­products.com. All returned service items whether under warranty or
not, must be freight pre-paid and accompany a return authorization
(R.A.) number. If the unit is under warranty you must provide a copy
of your proof of purchase invoice. Please contact ADJ Products, LLC
customer support for a R.A. number.

Saber Spot WW Handling Precautions

Caution! There are no user serviceable parts inside this unit. Do not

attempt any repairs yourself, doing so will void your manufactures
warranty. In the unlikely event your unit may require service please
contact ADJ Products, LLC.

During operation the housing may become extremely hot. Avoid
touching the unit with bare hands while in use.

ADJ Products, LLC will not accept any liability for any resulting dam­ages caused by the non-observance of this manual or any unauthor-

ized modication to this unit.

ADJ Products, LLC - www.adj.com - Saber Spot WW Instruction Manual Page 3ADJ Products, LLC - www.adj.com - Saber Spot WW Instruction Manual Page 2

Saber Spot WW Safety Precautions

Saber Spot WW DMX Set Up

For Your Own Personal Safety, Please Read and Understand This

Manual Completely Before You Attempt To Install Or Operate

This Unit!

• To reduce the risk of electrical shock or re, do not expose this unit
rain or moisture

• Do not spill water or other liquids into or on to your unit.

• Be sure that the local power outlet match that of the required volt­ age for your unit.

• Do not attempt to operate this unit if the power cord has been
frayed or broken.

• Do not attempt to remove or break o the ground prong from
the electrical cord. This prong is used to reduce the risk of electrical
shock and re in case of an internal short.

• Disconnect from main power before making any type of connection.

• Do not remove the cover under any conditions. There are no user
serviceable parts inside.

• Never operate this unit when it’s cover is removed.

• Always be sure to mount this unit in an area that will allow proper
ventilation. Allow about 6” (15cm) between this device and a wall.

• Do not attempt to operate this unit, if it becomes damaged.

• This unit is intended for indoor use only, use of this product out­ doors voids all warranties.

• Always mount this unit in safe and stable matter.

• Power-supply cords should be routed so that they are not likely to
be walked on or pinched by items placed upon or against them,
paying particular attention to cords at plugs, convenience recep­ tacles, and the point where they exit from the appliance.

• Cleaning -The fixture should be cleaned only as recommended by
the manufacturer. See page 21 for cleaning details.

• Heat -This fixture should be situated away from heat sources such
as radiators, heat registers, stoves, or other appliances (including
amplifiers) that produce heat.

• The fixture should be serviced by qualified service personnel when:
A. Objects have fallen, or liquid has been spilled into the appliance.
B. The appliance has been exposed to rain or water.
C. The appliance does not appear to operate normally or exhibits
a marked change in performance.

Power Supply: The ADJ Saber Spot WW contains a automatic volt-

age switch, which will auto sense the voltage when it is plugged into
the power source. With this switch there is no need to worry about the
correct power voltage, this unit can be plugged in anywhere.

DMX-512: DMX is short for Digital Multiplex. This is a universal pro-

tocol used by most lighting and controller manufactures as a form of
communication between intelligent fixtures and controllers. A DMX

controller sends DMX data instructions from the controller to the fix­ture. DMX data is sent as serial data that travels from fixture to fixture
via the DATA “IN” and DATA “OUT” XLR terminals located on all DMX
fixtures (most controllers only have a DATA “OUT” terminal).

DMX Linking: DMX is a language allowing all makes and models
of dierent manufactures to be linked together and operate from a
single controller, as long as all xtures and the controller are DMX

compliant. To ensure proper DMX data transmission, when using
several DMX fixtures try to use the shortest cable path possible. The
order in which fixtures are connected in a DMX line does not influence
the DMX addressing. For example; a fixture assigned a DMX address
of 1 may be placed anywhere in a DMX line, at the beginning, at the
end, or anywhere in the middle. Therefore, the first fixture controlled
by the controller could be the last fixture in the chain. When a fixture
is assigned a DMX address of 1, the DMX controller knows to send
DATA assigned to address 1 to that unit, no matter where it is located
in the DMX chain.

Data Cable (DMX Cable) Requirements (For DMX and Master/Slave
Operation): The Saber Spot WW can be controlled via DMX-512

protocol. The Saber Spot WW has 3 DMX channel modes. The DMX
address is set electronically using the controls on
the rear panel of the unit. Your unit and your DMX
controller require a approved DMX-512 110 Ohm
Data cable for data input and data output (Figure

1). We recommend Accu-Cable DMX cables. If you
are making your own cables, be sure to use stan­dard 110-120 Ohm shielded cable (This cable may
be purchased at almost all professional sound and
lighting stores). Your cables should be made with

Figure 1

ADJ Products, LLC - www.adj.com - Saber Spot WW Instruction Manual Page 5ADJ Products, LLC - www.adj.com - Saber Spot WW Instruction Manual Page 4

Saber Spot WW DMX Set Up

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

DMX512

DMX+,DMX-,COMMON

1

2

3

Termination reduces signal errors and
avoids signal transmission problems
and interference. It is always advisable
to connect a DMX terminal, (Resistance
120 Ohm 1/4 W) between PIN 2 (DMX-)
and PIN 3 (DMX +) of the last fixture.

POWER

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

Saber Spot WW DMX Set Up

a male and female XLR connector on either end of the cable. Also
remember that DMX cable must be daisy chained and cannot be split.

Notice: Be sure to follow gures two and three when making your own

cables. Do not use the ground lug on the XLR connector. Do not con­nect the cable’s shield conductor to the ground lug or allow the shield
conductor to come in contact with the XLR’s outer casing. Grounding
the shield could cause a short circuit and erratic behavior.

COMMON

1

DMX512 IN

3

3-PIN XLR

2

Figure 2

XLR Pin Conguration

Pin 1 = Ground

Pin 2 = Data Compliment (negative)

Pin 3 = Data True (positive)

XLR Male Socket

1 Ground

Figure 3

DMX512 OT

3-PIN XLR

2 Cold

3 Hot

1

3

2

XLR Female Socket

2 Cold

DMX +

DMX -

1 Ground

3 Hot

5-Pin XLR DMX Connectors.

Some manufactures use 5-pin DMX-

512 data cables for DATA transmission in place of 3-pin. 5-pin DMX
xtures may be implemented in a 3-pin DMX line. When inserting stan­dard 5-pin data cables in to a 3-pin line a cable adaptor must be used,
these adaptors are readily available at most electric stores. The chart
below details a proper cable conversion.

3-Pin XLR to 5-Pin XLR Conversion

Conductor 5-Pin XLR Male (In)3-Pin XLR Female (Out)

Ground/Shield

Data Compliment (- signal)

Data True (+ signal)

Not Used

Not Used

Pin 1

Pin 2

Pin 3

Pin 1

Pin 2

Pin 3

Pin 4 - Do Not Use

Pin 5 - Do Not Use

Special Note: Line Termination.

used, you may need to use a terminator on the last unit to avoid erratic
behavior. A terminator is a 110-120 ohm 1/4 watt resistor which is con-

When longer runs of cable are

nected between pins 2 and 3 of a male XLR connector (DATA + and
DATA -). This unit is inserted in the female XLR connector of the last
unit in your daisy chain to terminate the line. Using a cable terminator
(ADJ part number Z-DMX/T) will decrease the possibilities of erratic
behavior.

ADJ Products, LLC - www.adj.com - Saber Spot WW Instruction Manual Page 6 ADJ Products, LLC - www.adj.com - Saber Spot WW Instruction Manual Page 7

Termination reduces signal errors and

1

avoids signal transmission problems

3

and interference. It is always advisable

2

to connect a DMX terminal, (Resistance
120 Ohm 1/4 W) between PIN 2 (DMX-)
and PIN 3 (DMX +) of the last fixture.

Figure 4

Saber Spot WW System Menu

Software Update

Display Menu

Special Remark:

SN MENU DISPLAY FUNCTION

1

2 CHANNNEL 4CH 1/2/4CH(see channel mode)

3 Slave Slave mode

4

5

6

7

8

9 TempUnit C/ F

10 Temp Val Temperature show: xxx F

11 AUTOLOCK Display keylock OFF/ON

12 IR Active IR setting OFF/ON

13 FlipDisplay Flip display OFF/ON

Please Wait ...

ADJ

SOFTWARE V1.0 3
About LED protection ：

When reach 65 degree, the power consumption is reduced to 82%. When the sensor is

damaged, the power consumption is reduced to 65%.

DMX MODE
ADDR：001

LOOK

Store:01

Reset ？

NO

Manual

W 000-255 S 000- 255

DimCurve

Standard

NO DMX No DMX mode

Hold Blackout, Hold, LOOK

Yes,press ENTER to resume the factory

Standard, Stage, TV, Architec,

Address setting

001- 512

Store mode 01- 13

default setting

Manual dimmer

W 000-255 strobe ：S000- 255

5 kinds Dimmer curve

Theatre

Saber Spot WW System Menu

System Menu: When making adjustments press ENTER to

conrm your setup then press and hold the MENU button

for at least 3 seconds. To exit without making any adjust-

ments press the MENU button. The display will lock after 30
seconds, press the MENU button for 3 seconds to unlock.

DMX MODE - DMX Address Setting.

1. Press the either the MENU, UP, or DOWN buttons until “DMX
MODE” is displayed, press ENTER.

2. The current address will now be displayed and ashing.
Press the UP or DOWN buttons to nd your desired address.
Press ENTER to set your desired DMX address.

CHANNEL - This will let select your desired DMX

channel mode.

1. Press the either the MENU button until “CHANNEL” is dis­played, press ENTER. The current DMX channel mode will be

displayed.

2. Press the UP or DOWN buttons to nd your desired DMX
channel mode and press ENTER to conm and exit.

SLAVE - This will let you set the unit as the slave in a

master/slave conguration.

1. Press the MENU button until “SLAVE” is displayed, press
ENTER.

LOOK - In this mode you can run a show mode.

1. Press the MENU button until “LOOK” is displayed, press
ENTER.

2. Use the UP or DOWN buttons to nd your desired mode.

ADJ Products, LLC - www.adj.com - Saber Spot WW Instruction Manual Page 9ADJ Products, LLC - www.adj.com - Saber Spot WW Instruction Manual Page 8