Adj Royal SKY User Manual

ROYAL SKY

©2015 ADJ Products, LLC all rights reserved. Information,

specications, diagrams, images, and instructions herein are

subject to change without notice. ADJ Products, LLC logo and
identifying product names and numbers herein are trademarks
of ADJ Products, LLC. Copyright protection claimed includes all
forms and matters of copyrightable materials and information
now allowed by statutory or judicial law or hereinafter granted.
Product names used in this document may be trademarks or
registered trademarks of their respective companies and are
hereby acknowledged. All non-ADJ Products, LLC brands and
product names are trademarks or registered trademarks of their
respective companies.

ADJ Products, LLC and all aliated companies hereby dis-
claim any and all liabilities for property, equipment, building,
and electrical damages, injuries to any persons, and direct or
indirect economic loss associated with the use or reliance of
any information contained within this document, and/or as a
result of the improper, unsafe, unsucient and negligent as­sembly, installation, rigging, and operation of this product.

3/15

User Instructions

Europe Energy Saving Notice
Energy Saving Matters (EuP 2009/125/EC)
Saving electric energy is a key to help protecting the enviroment.

Please turn o all electrical products when they are not in use. To

avoid power consumption in idle mode, disconnect all electrical

equipment from power when not in use. Thank you!

Royal Sky General Introduction

Royal Sky General Instructions

Unpacking: Thank you for purchasing the Royal Sky by ADJ Products,

LLC®. Every Royal Sky has been thoroughly tested and has been shipped
in perfect operating condition. Carefully check the shipping carton for
damage that may have occurred during shipping. If the carton appears to

be damaged, carefully inspect your xture for any damage and be sure all

equipment necessary to operate the unit has arrived intact. In the event
damage has been found or parts are missing, please contact our toll free
customer support number for further instructions. Please do not return

this unit to your dealer without contacting customer support rst. PLEASE
recycle the shipping carton whenever possible.

Introduction: The Royal Sky is an incredible six channel DMX intelligent,
green and blue laser fixture. The blue laser combined with the green laser
creates an amazing “Liquid Sky” effect when projected. The Royal Sky
can operate as a stand alone fixture, or in a Master/Slave configuration.
The Royal Sky has three operating modes; sound active mode, show
mode, or it can be controlled via DMX. This unit is suitable for theaters,

studios, retail stores, and other similar locations. This fixture is suitable
for theaters, studios, retail stores, and other similar locations. For best

results use fog or special effects smoke to enhance the beams projections.

Customer Support: ADJ® provides a toll free customer support line, to
provide set up help and to answer any question should you encounter
problems during your set up or initial operation. You may also visit us on
the web at www.adj.com for any comments or suggestions. For service
related issue please contact ADJ®. Service Hours are Monday through

Friday 8:00 a.m. to 4:30 p.m. Pacic Standard Time.
Voice: [phone]
Fax: [phone]
E-mail: [e-mail]
To purchase parts online visit http://parts.americandj.com

Warning! To prevent or reduce the risk of electrical shock or re, do not
expose this unit to rain or moisture.

Caution! There are no user serviceable parts inside this unit. Do not

attempt any repairs yourself, doing so will void your manufactures war­ranty. In the unlikely event your unit may require service please contact
ADJ customer support.

Please carefully read and understand the instructions in this manual

thoroughly before attempting to operate this unit. These instructions

contain important safety information regarding the use and mainte­nance of this unit. Please keep this manual with the unit, for future
reference.

CAUTION IMPORTANT! When installing this projector, make sure
that it is mounted in a manner that prevents the audience from
looking directly into the beam, and the beam from striking the
audience.

Royal Sky Features

• Green Laser & Violet Blue Laser

• 6 Channel DMX Control

• 3 Operating Modes - Sound Active, Show Mode, & DMX Control

• 20 Laser Patterns

• Digital Display for Address and Function Setting

• UC3 Controller (Not Included)

• Run as Stand Alone unit or in a Master-Slave Conguration

• Power Cord Daisy Chain up to 16 units max. See page 16

Royal Sky Installation

The unit should be mounted using a mounting clamp (not provided),
axing it to the mounting bracket that is provided with the unit.
Always ensure that the unit is rmly xed to avoid vibration and slip-

ping while operating. Always ensure that the structure to which you
are attaching the unit is secure and is able to support a weight of 10
times the unit’s weight. Also always use a safety cable that can hold

12 times the weight of the unit when installing the xture.
The equipment must be installed by a professional, and it must be

installed in a place where it is out of the reach of people’s grasp.

Royal Sky Warranty Registration

The Royal Sky carries a 90 day limited warranty. Please fill out the
enclosed warranty card to validate your purchase. All returned ser­vice items whether under warranty or not, must be freight pre-paid
and accompany a return authorization (R.A.) number. If the unit is
under warranty you must provide a copy of your proof of purchase
invoice. Please contact ADJ

® customer support for a R.A. number.

ADJ Products, LLC - www.adj.com - Royal Sky Instruction Manual Page 3ADJ Products, LLC - www.adj.com - Royal Sky Instruction Manual Page 2

Royal Sky Safety Precautions

!

!

LASER RADIATION AVOID
DIRECT EYE EXPOSURE

Maximum output <5 mW
Wavelength: 405, 532nm

This device complies with 21 CFR chapter I,
Subchapter J, or CFR 1040.10 and 1040.11

Safety Issues: This unit may “pop” the fuse if the maximum allotted
load of 2 amps is reached.

• To reduce the risk of electrical shock or re, do not expose this unit

rain or moisture.

• Do not spill water or other liquids into or on to your unit.

• Do not attempt to remove or break o the ground prong from the
electrical cord. This prong is used to reduce the risk of electrical
shock and re in case of an internal short. Do not attempt to oper-

ate this unit if the power cord has been frayed or broken.

• Disconnect from main power before making any type of connection.

• Do not remove the cover under any conditions. There are no user

serviceable parts inside.

• Always be sure to mount this unit in an area that will allow proper
ventilation. Allow about 6” (15cm) between this device and a wall.

• Do not attempt to operate this unit, if it becomes damaged.

• This unit is intended for indoor use only, use of this product out-

doors voids all warranties.

• During long periods of non-use, disconnect the unit’s main power.

• Always mount this unit in safe and stable matter.

• Power cords should be routed so they are not likely to be walked

on, pinched by items placed upon or against them.

• Cleaning -The fixture should be cleaned only as recommended by

the manufacturer. See page 19 for cleaning details.

• Heat -The appliance should be situated away from heat sources

such as radiators, heat registers, stoves, or other appliances
(including amplifiers) that produce heat.

• The fixture should be serviced by qualified service personnel when:
A. The power-supply cord or the plug has been damaged.
B. Objects have fallen, or liquid has been spilled into the unit.
C. The unit has been exposed to rain or water.
D. The unit does not appear to operate normally or exhibits a

marked change in performance.

ADJ Products, LLC - www.adj.com - Royal Sky Instruction Manual Page 5

Class IIIa laser product

Royal Sky Laser Warnings and Safety

NON-INTERLOCKED HOUSING WARNING

The Royal Sky contains high power laser devices internally. Do not
open the laser housing, due to the potential exposure to unsafe levels
of laser radiation. The laser power levels, if the unit is opened, can
cause instant blindness, skin burns and res.

STOP AND READ ALL LASER SAFETY DATA

OPERATION INSTRUCTIONS AND LASER SAFETY

The light source emitted from this product can potentially cause eye
injury if not set up and used properly. The light source emitted from a
laser is very dierent from any other light sources with which you may

be aware of. Laser light is thousands of times more concentrated

than any light from any other kind of light source. This concentration

of light can cause instant eye injuries, primarily by burning the retina
(the back of your eyeball contatining cells that are sensitive to light).
Even if you cannot feel “heat” from a laser beam, it can still poten­tially injure or blind you or your audience. Even very small amounts
of laser beam light are potentially hazardous even at long distances.
Laser eye injuries can be sustained faster than you can blink.

Do not think that because this laser splits the laser beam into hun­dreds of beams and that the laser beam is scanned out in high

speed, that an individual laser beam is safe for eye exposure. This
laser uses dozens of milliwatts of laser power (Class 3B levels inter-

nally) before it splits into multiple beams (Class 3R levels). Many of
the individual beams are potentially hazardous to the eyes.

Do not that because the laser light is moving, it is safe. This is not

true. Nor, do the laser beams always move. Since eye injuries can
occur instantly, it is critical to prevent even the smallest possibility of

any direct eye exposure. In the laser safety regulation, it is not legal
to aim Class 3R lasers in areas which people can get exposed. This

is true even if it is aimed below people’s faces, such as on a dance

oor.

Do not operate the laser without rst reading and understanding

all safety and technical data in this manual.

Always set up and install all laser eects so that all laser light is at
least 3 meters (9.8 feet) above the oor on which people can stand.

ADJ Products, LLC - www.adj.com - Royal Sky Instruction Manual Page 6

Royal Sky Laser Warnings and Safety

After setting up, and before public use, test laser to ensure proper
function. Do not use if any defect is detected. Do not use if laser
emits only one or two laser beams rather than dozens/hundreds, as

this could indicate damage to the diraction grating optic, and could

allow emission of higher laser levels above Class 3R.

Do not point lasers at people or animals. Never look into the laser
aperture or laser beams.

Do not point lasers in areas in which people can potentially get

exposed, such as uncontrolled balconies, etc.

Do not point lasers at highly reective surfaces, such as windows,
mirrors and shiny metal. Even laser reections can be hazardous.

Never point a laser at aircraft, this is a federal oense.

Never point un-terminated laser beams into the sky.

Do not expose the output optic (aperture) to cleaning chemicals.

Do not use laser if the laser appears to be emitting only one or two

beams.

Do not use the laser if the housing is damaged, the housing is open,
or if the optics appear damaged in any way.

Never open the laser housing. The high laser power levels inside of
the protective housing can start res, burn skin and will cause instant

eye injury.

Never leave this device running unattended.

Royal Sky Laser Warning Labels

LASER RADIATION IS

EMITTED FROM THIS APERTURE

LE RAYONNEMENT

LASER EST EMIS PAR CETTE OUVERTURE

AVOID EX POSUR E

,

EVITEZ L EXPOSITION

53 mm

LASER RADIATION

AVOID DIRECT EYE EXPOSURE

CLASS 3R LASER PRODUCT

RAYONNEMENT LASER

EVITEZ TOUTE EXPOSITION DIRECTE

CLASSE 3R PRODUIT LASER

39mm

41 mm

LASER RADIATION AVOID
DIRECT EYE EXPOSURE

RAYONNEMENT LASER,
EVITEZ TOUTE
EXPOSITION DIRECTE

Maximum output <5 mW
Wavelength: 532nm, 450nm
Class IIIa laser product

Sortie maximale<5m W
Longueur d'onde: 532 nm,
450 nm Classe IIIa produit laser

This device complies with 21 CFR chapter I,
Subchapter J, CFR 1040.10 and 1040.11

Cet appareil est conforme aux normes 21
CFR Chapitre I, Sous-chapitre J,
CFR 1040,10 et 1040.11

Specification stickers

Specification autocollants

66 mm

48 mm

33 mm

The operation of a class 3R laser show is only allowed if the show

is controlled by a skilled and well- trained operator, familiar with the
data included in this manual.

The legal requirements for using laser entertainment products vary
from country to country. The user is responsible for the legal require-

ments at the location/country of use.

Always use proper lighting safety cables when hanging lights and

eects overhead.

52 mm

CAUTION - CLASS 3R

LASER RADIATION WHEN OPEN

AVOID DIRECT EYE EXPOSURE

ATTENTION-CLASSE 3R

RAYONNEMENT LASER LORSQUE OUVERT

EVITEZ TOUTE EXPOSITION DIRECTE

26 mm

ADJ Products, LLC - www.adj.com - Royal Sky Instruction Manual Page 8ADJ Products, LLC - www.adj.com - Royal Sky Instruction Manual Page 7

Royal Sky Set Up

Royal Sky Set Up

Power Supply: The ADJ® Royal Sky contains a automatic voltage

switch, which will auto sense the voltage when it is plugged into the
power source. With this switch there is no need to worry about the cor­rect power voltage, this unit can be plugged in anywhere.

DMX-512: DMX is short for Digital Multiplex. This is a universal pro-

tocol used by most lighting and controller manufactures as a form of
communication between intelligent fixtures and controllers. A DMX

controller sends DMX data instructions from the controller to the fix­ture. DMX data is sent as serial data that travels from fixture to fixture
via the DATA “IN” and DATA “OUT” XLR terminals located on all DMX
fixtures (most controllers only have a DATA “OUT” terminal).

DMX Linking: DMX is a language allowing all makes and models of
dierent manufactures to be linked together and operate from a sin­gle controller, as long as all xtures and the controller are DMX com-

pliant. To ensure proper DMX data transmission, when using several
DMX fixtures try to use the shortest cable path possible. The order
in which fixtures are connected in a DMX line does not influence the
DMX addressing. For example; a fixture assigned a DMX address of 1
may be placed anywhere in a DMX line, at the beginning, at the end,
or anywhere in the middle. Therefore, the first fixture controlled by the
controller could be the last fixture in the chain. When a fixture is as­signed a DMX address of 1, the DMX controller knows to send DATA
assigned to address 1 to that unit, no matter where it is located in the
DMX chain.

Data Cable (DMX Cable) Requirements (For DMX and Master/Slave
Operation): The Royal Sky can be controlled via DMX-512 protocol.

The Royal Sky is a 6 channel DMX unit. The DMX address is set elec­tronically using the controls on the rear panel of

the unit. Your unit and your DMX controller require
a approved DMX-512 110 Ohm Data cable for data
input and data output (Figure 1). We recommend
Accu-Cable DMX cables. If you are making your
own cables, be sure to use standard 110-120 Ohm
shielded cable (This cable may be purchased at

almost all professional sound and lighting stores).
Your cables should be made with a male and

female XLR connector on either end of the cable. Also remember that

ADJ Products, LLC - www.adj.com - Royal Sky Instruction Manual Page 9 ADJ Products, LLC - www.adj.com - Royal Sky Instruction Manual Page 10

Figure 1

DMX cable must be daisy chained and cannot be split.

Notice: Be sure to follow gures two and three when making your own

cables. Do not use the ground lug on the XLR connector. Do not con­nect the cable’s shield conductor to the ground lug or allow the shield

conductor to come in contact with the XLR’s outer casing. Grounding

the shield could cause a short circuit and erratic behavior.

COMMON

1

DMX512 IN

3

3-PIN XLR

1 Ground

3 Hot

2

XLR Pin Conguration

Pin 1 = Ground

Pin 2 = Data Compliment (negative)

Pin 3 = Data True (positive)

Figure 2

When longer runs of cable are

Figure 4

XLR Male Socket

1 Ground

Figure 3

DMX512 OUT

3-PIN XLR

2 Cold

3 Hot

1

3

2

DMX +

DMX -

XLR Female Socket

2 Cold

Special Note: Line Termination.

used, you may need to use a terminator on the last unit to avoid erratic

behavior. A terminator is a 110-120 ohm 1/4 watt resistor which is con­nected between pins 2 and 3 of a male XLR connector (DATA + and
DATA -). This unit is inserted in the female XLR connector of the last

unit in your daisy chain to terminate the line. Using a cable terminator

(ADJ part number Z-DMX/T) will decrease the possibilities of erratic

behavior.

Termination reduces signal errors and

1

avoids signal transmission problems

3

and interference. It is always advisable

2

to connect a DMX terminal, (Resistance
120 Ohm 1/4 W) between PIN 2 (DMX-)
and PIN 3 (DMX +) of the last fixture.

Royal Sky Set Up

Royal Sky System Menu

5-Pin XLR DMX Connectors.

Some manufactures use 5-pin DMX-

512 data cables for DATA transmission in place of 3-pin. 5-pin DMX
xtures may be implemented in a 3-pin DMX line. When inserting stan-

dard 5-pin data cables in to a 3-pin line a cable adaptor must be used,

these adaptors are readily available at most electric stores. The chart

below details a proper cable conversion.

3-Pin XLR to 5-Pin XLR Conversion

Conductor 5-Pin XLR Male (In)3-Pin XLR Female (Out)

Ground/Shield

Data Compliment (- signal)

Data True (+ signal)

Not Used

Not Used

Pin 1

Pin 2

Pin 3

Pin 1

Pin 2

Pin 3

Pin 4 - Do Not Use

Pin 5 - Do Not Use

ADJ Products, LLC - www.adj.com - Royal Sky Instruction Manual Page 12ADJ Products, LLC - www.adj.com - Royal Sky Instruction Manual Page 11

Royal Sky System Menu

Royal Sky System Menu

System Menu: When conrming your setting press ENTER
and then hold MENU for at least 2-3 seconds, or you can
wait 1 minute for automatic setup. To exit without making
any adjustments press the MENU button.

ADDR - DMX Address Setting via control board -

1. Press the MENU button until “ADDR” is displayed, press ENTER.

2. “X” will now be displayed, “X” represents the displayed address.
Press the UP or DOWN buttons to nd your desired address.

3. Press ENTER to conrm, then connect your DMX controller.
NOTE: If after you connect your DMX controller the unit does not fall
into DMX mode, press and hold the MENU button for at least 3 sec-

onds.

SLND - This will let you set unit as a slave in a master/

slave conguration.

1. Press the MENU button until “SLND” is displayed, press ENTER.

Either “SL 1” or “SL 2” will be displayed.

2. Press the UP or DOWN buttons until your desired setting is dis­played, press ENTER to conm.

NOTE: In a Master/Slave conguration you can make one xture the
Master and then set the next xture to “SL 2”, the xtures will now

have contrast movement to each other.

for at least 3 seconds.

SOUN - In this mode you can run in sound active mode.

1. Press the MENU button until “SOUN” is displayed, press ENTER.

2. Either “ON” or “OFF” will now be displayed. Press the UP or DOWN

buttons to select one or the other.

3. When you have made your selection, press the ENTER, and then
press and hold the MENU button for at least 3 seconds to conrm.

SENS - Sound sensitivity control.

1. Press the MENU button until “SENS” is displayed, press ENTER.

2. The display will show a number between 0-100. Press the UP or
DOWN buttons to adjust the sound sensitivity. 0 being the least sen-

sitive and 100 the most sensitive.

3. Press the ENTER to conrm.

BLND - This will control blackout

1. Press the MENU button until “BLND” is displayed, press ENTER.

2. Either “YES” or “NO” will now be displayed. Press the UP or DOWN

buttons to select one or the other.

3. Press ENTER, and then press and hold the MENU button for at least
three seconds to conrm.

SHND: SH 0 - SH 18 - Show modes 0-18 (Factory

programs) Show Mode can run with or without sound active
mode on. With sound active mode on, the shows will tend to
run faster.

1. Press the MENU button until “SHND” is displayed, press ENTER.

2. “SH X” will now be displayed, “X” representing a number between

0-18. Shows 1-18 are preprogrammed shows, while “SH 0” is random
show mode. Press the UP or DOWN buttons to nd your desired show.

3. Press ENTER to conrm, and then press and hold the MENU button

LED - With this function the LED display will turn off after

2 minutes.

1. Press the MENU button until “LED” is displayed, press ENTER.

2. Either “ON” or “OFF” will now be displayed. Press the UP or DOWN
buttons to select “ON” to keep the LED display on at all times, or
“OFF” to allow the LED display to turn o after 2 minutes. Press any

button to turn on the LED display again.

ADJ Products, LLC - www.adj.com - Royal Sky Instruction Manual Page 14ADJ Products, LLC - www.adj.com - Royal Sky Instruction Manual Page 13

Royal Sky Operation Royal Sky System Menu

3. Press ENTER, and then press and hold the MENU button for at least
three seconds to conrm.

DISP - This function will “ip” the LED display 180º.

1. Press the MENU button until “DISP” is displayed, press ENTER.

2. Press ENTER to “ip” the display. Press ENTER to “ip” it again.

Press MENU when you have decided on your desired display setup.

TEST - This function will allow you to test the pan & tilt

functions.

1. Press the MENU button until “TEST” is displayed, press ENTER.

2. Either “PAN”, “TILT” or “P T” will be displayed. Use the UP or
DOWN buttons to scroll to the function you would like to test and
press ENTER. The function will now run a self test. Press MENU to
exit

FHRS - With this function you can display the running

time of the unit.

1. Press the MENU button until “FHRS” is displayed, press ENTER.

2. The running time of the xture will now be displayed. Press MENU
to exit.

VER - This will display the software version

1. Press the MENU button until “VER” is displayed. Press the ENTER

button and the software vesion will be displayed.

2. Press the MENU button to leave this function.

RSET - Use this function to reset the unit.

1. Tap the MENU button until “RSET” is displayed, press ENTER.

2. The xture will now reset.

CAUTION IMPORTANT! When installing this projector, make sure
that it is mounted in a manner that prevents the audience from
looking directly into the beam, and the beam from striking the

audience.

Operating Modes: The Royal Sky has three different operating
modes.

Universal DMX Control:

universal DMX-512 controller to control the individual lasers, patterns,
rotation, movement, and zoom. A DMX controller allows you to create
unique programs tailored to your individual needs.

1. The Royal Sky is a five channel DMX fixture. See pages 17-18 for
detailed description of the DMX values and traits.

2. To control your fixture in DMX mode, follow the set-up procedures
on pages 8-10 as well as the set-up specifications that are includ­ ed with your DMX controller.

3. Use the controller’s faders to control the various DMX fixture traits.

4. This will allow you to create your own programs.

5. Follow the instruction on page 11 to set the DMX address.

6. For longer cable runs (more than a 100 feet) use a terminator on
the last fixture.

7. For help operating in DMX mode consult the manual included
with your DMX controller.

This function allows you to use a Elation®

Sound Active Mode (Stand Alone or Master-Slave): This mode

allows either single unit or several units linked together, to run to the
beat of the music.

1. Press the MENU button until “SOUN” is displayed, and press

ENTER.

2. Press the UP or DOWN buttons so that “ON” is displayed, and

press ENTER to conrm and then hold MENU for at least 2-3 sec-

onds.

3. To adjust the sound sensitivity press the MENU button until
“SENS” is displayed and press ENTER. Use the UP or DOWN

buttons to adjust sensitivity.

4. The optional UC3 Controller (not included) may be used to con-
trol different functions including blackout. See page 18 for UC3

controls and functions.

ADJ Products, LLC - www.adj.com - Royal Sky Instruction Manual Page 15 ADJ Products, LLC - www.adj.com - Royal Sky Instruction Manual Page 16

Royal Sky Operation

Show Mode (Stand Alone or Master-Slave): This mode allows a

single unit or several units linked together, to run your desired prepro­grammed show.

1. Press the MENU button until

“SHND” is displayed, and press

ENTER.

2.

Press the UP or DOWN buttons until you nd your desired show,

press ENTER to conrm and then hold MENU for at least 2-3 sec-

onds.

3. The optional UC3 Controller (not included) may be used to con-

trol different functions including blackout. See page 18 for UC3

controls and functions.

Royal Sky Master-Slave Configuration

Master-Slave Conguration: This function will allow you to link

up to 16 units together and operate without a controller. The units will
be sound activated. In Master-Slave operation one unit will act as the
controlling unit and the others will react to the controlling units pro­grams. Any unit can act as a Master or as a Slave.

1. Using approved DMX data cables, daisy chain your units togeth-
er via the XLR connector on the rear of the units. Remember the
Male XLR connector is the input and the Female XLR connector
is the output. The rst unit in the chain (master) will use the female
XLR connector only - The last unit in the chain will use the male
XLR connector only. For longer cable runs we suggest a termina­ tor at the last fixture.

2. Set your Master unit to your desired operating mode.

3. On the slave units press the MENU button until “SLND” is dis-
played, and press ENTER. Choose either “SL 1” or “SL 2” and
press ENTER. See page 12 for more info.

4. The slave units will now follow the Master unit.

Royal Sky Power Cord Daisy Chain

With this feature you can connect the xtures to one another
using the IEC input and output sockets. The quantity that can be
connected is 16 xtures maximum. After 16 xtures you will need
to use a new power outlet. They must be the same xtures. DO
NOT mix xtures.

ADJ Products, LLC - www.adj.com - Royal Sky Instruction Manual Page 17

Royal Sky DMX Traits

Channel Value Function

1 GREEN LASER

0 - 7 OFF
8 - 15 ON
16 - 131 LASER DASH EFFECT
132 - 247 DOT ON LINE EFFECT
248 - 255 ON
2 BLUE LASER
0 - 7 OFF
8 - 15 ON
16 - 131 LASER DASH EFFECT
132 - 247 DOT ON LINE EFFECT
248 - 255 ON
3 PATTERNS
0 - 12 PATTERN 1
13 - 25 PATTERN 2
26 - 38 PATTERN 3
39 - 51 PATTERN 4
52 - 63 PATTERN 5
64 - 76 PATTERN 6
77 - 89 PATTERN 7
90 - 102 PATTERN 8
103 - 115 PATTERN 9
116 - 127 PATTERN 10
128 - 140 PATTERN 11
141 - 153 PATTERN 12
154 - 166 PATTERN 13
167 - 179 PATTERN 14
180 - 191 PATTERN 15
192 - 204 PATTERN 16
205 - 217 PATTERN 17
218 - 230 PATTERN 18
231 - 243 PATTERN 19
244 - 255 PATTERN 20

ADJ Products, LLC - www.adj.com - Royal Sky Instruction Manual Page 18

Royal Sky DMX Traits

Channel Value Function

4 LASER MOVEMENT

0 - 9 NO MOVEMENT
10 - 120 LEFT - RIGHT FAST - SLOW
121 - 134 NO MOVEMENT
135 - 245 UP - DOWN SLOW - FAST
246 - 255 NO MOVEMENT
246 - 255 NO ROTATION
5 LASER ROTATION
0 - 9 NO ROTATION
10 - 120 COUNTER-CLOCKWISE
FAST - SLOW
121 - 134 NO ROTATION
135 - 245 CLOCKWISE SLOW - FAST
246 - 255 NO ROTATION
6 ZOOM
0 - 127 ZOOM OUT - ZOOM IN
128 - 255 ZOOM IN - OUT SLOW - FAST

Royal Sky UC3 Control

Royal Sky Fuse Replacement

Locate and remove the unit’s power cord. Once the cord has been

removed located the fuse holder located inside the power socket.
Insert a flat-head screw driver into the power socket and gently pry
out the fuse holder. Remove the bad fuse and replace with a new one.

The fuse holder has a built-in socket for a spare fuse be sure not to

confuse the spare fuse with active fuse.

Royal Sky Cleaning

Fixture Cleaning: Due to fog residue, smoke, and dust cleaning

the internal and external lenses should be carried out periodically to

optimize light output.

1. Use normal glass cleaner and a soft cloth to wipe down the out­ side casing.

2. Clean the external optics with glass cleaner and a soft cloth every

20 days.

3. Always be sure to dry all parts completely before plugging the
unit back in.

Cleaning frequency depends on the environment in which the fixture

operates (I.e. smoke, fog residue, dust, dew). In heavy use we recom­mend cleaning on a monthly basis. Periodic cleaning will ensure lon­gevity, and crisp beam output.

ADJ Products, LLC - www.adj.com - Royal Sky Instruction Manual Page 19

Royal Sky Trouble Shooting

Trouble Shooting: Listed below are a few common problems that
you may encounter, with solutions.

No laser output from the unit;

1. Be sure you have turned “ON” the unit.

2. Be sure the external fuse has not blown. The fuse is located on
the rear panel of the unit.

3. Be sure the fuse holder is completely and properly seated.

4. Be sure the unit is not in blackout mode.

Unit does not respond to sound;

1. Low frequencies (bass) should cause the unit to react to sound.

Tapping on the microphone, quiet or high pitched sounds may

not activate the unit.

ADJ Products, LLC - www.adj.com - Royal Sky Instruction Manual Page 20

Royal Sky Warranty

MANUFACTURER’S LIMITED WARRANTY

A. ADJ Products, LLC hereby warrants, to the original purchaser, ADJ Products, LLC products
to be free of manufacturing defects in material and workmanship for a prescribed period from
the date of purchase (see specific warranty period on reverse). This warranty shall be valid only if the
product is purchased within the United States of America, including possessions and
territories. It is the owner’s responsibility to establish the date and place of purchase by acceptable
evidence, at the time service is sought.

B. For warranty service you must obtain a Return Authorization number (RA#)

before sending back the product–please contact ADJ Products, LLC Service Department
at 800-322-6337. Send the product only to the ADJ Products, LLC factory. All

shipping charges must be pre-paid. If the requested repairs or service (including
parts replacement) are within the terms of this warranty, ADJ Products, LLC will pay return
shipping charges only to a designated point within the United States. If the entire instrument is
sent, it must be shipped in it’s original package. No accessories should be shipped with the product. If
any accessories are shipped with the product, ADJ Products, LLC shall have no liability whatsoever for
loss of or damage to any such accessories, nor for the safe return thereof.

C. This warranty is void if the serial number has been altered or removed; if the product is modified in any
manner which ADJ Products, LLC concludes, after inspection, affects the reliability of the product; if the
product has been repaired or serviced by anyone other than the ADJ Products, LLC factory unless prior
written authorization was issued to purchaser by ADJ Products, LLC; if the product is damaged because
not properly maintained as set forth in the instruction manual.

D. This is not a service contract, and this warranty does not include maintnance, cleaning or periodic check
up. During the period specified above, ADJ Products, LLC will replace defective parts at its expense
with new or refurbished parts, and will absorb all expenses for warranty service and repair labor by
reason of defects in material or workmanship. The sole responsibility of ADJ Products, LLC under this
warranty shall be limited to the repair of the product, or replacement thereof, including parts, at the sole
discretion of ADJ Products, LLC. All products covered by this warranty were manufactured after August
15, 2012, and bear indentifying marks to that effect.

E. ADJ Products, LLC reserves the right to make changes in design and/or improvements upon its products
without any obligation to include these changes in any products theretofore manufactured.

No warranty, whether expressed or implied, is given or made with respect to any accessory supplied with
products described above. Except to the extent prohibited by applicable law, all implied warranties made
by ADJ Products, LLC in connection with this product, including warranties of merchantability or fitness,
are limited in duration to the warranty period set forth above. And no warranties, whether expressed or
implied, including warranties of merchantability or fitness, shall apply to this product after said period
has expired. The consumer’s and/or Dealer’s sole remedy shall be such repair or replacement as is
expressly provided above; and under no circumstances shall ADJ Products, LLC be liable for any loss or
damage, direct or consequential, arising out of the use of, or inability to use, this product.

This warranty is the only written warranty applicable to ADJ Products, LLC Products and
supersedes all prior warranties and written descriptions of warranty terms and conditions heretofore
published.

MANUFACTURER’S LIMITED WARRANTY PERIODS:

 •LightingProducts=1-year(365days)LimitedWarranty(Such as: Special Effect Lighting, Intelligent

Lighting, UV lighting, Strobes, Fog Machines, Bubble Machines, Mirror Balls, Par Cans, Trussing,
Lighting Stands etc. excluding LED and lamps)

 •LaserProducts=1Year(365Days)LimitedWarranty(excluding laser diodes which have a 6 month

limited warranty)

 •L.E.D.Products=2-year(730days)LimitedWarranty(excluding motors, PCB boards, and power
supplies, which have a 1-year (365 day Limited Warranty) batteries which have a 180 day limited war-

ranty). Only the L.E.D.s carry a 2-year warranty (excluding StarTec Series which a carries a 90 Day

Limited Warranty)

•ADJDMXControllers=2Year(730Days)LimitedWarranty(excluding faders and tact switches)

ADJ Products, LLC - www.adj.com - Royal Sky Instruction Manual Page 21 ADJ Products, LLC - www.adj.com - Royal Sky Instruction Manual Page 22

Royal Sky Notes

Royal Sky Specifications

Model: Royal Sky

Voltage: 100-240V, 50/60Hz

Power Cord Daisy Chain: 16 Fixtures Max.

Power Consumption: 20W

Lasers: Green Diode
Violet Blue Diode
Beam Angle: 38 Degrees
Dimensions: 8.5”(L) x 11.5”(W) x 7.75”(H)
213mm x 289mm x 194mm
Colors: Green & Violet Blue
Weight: 9 Lbs. / 3.8 kgs.

Fuse: 7 Amp
Duty Cycle: None
DMX: 6 DMX Channels

Sound Active: Ye s
Working Position: Any Safe, Secure Position

Warranty: 90 Days

Auto Sensing Voltage: This xture contains a automatic volt-

age switch, which will auto sense the voltage when it is plugged
into the power source.

Please Note: Specications and improvements in the design

of this unit and this manual are subject to change without any
prior written notice.

ADJ Products, LLC - www.adj.com - Royal Sky Instruction Manual Page 23

ADJ Products, LLC

6122 S. Eastern Ave. Los Angeles, CA 90040 USA

Tel: [phone] / Fax: [phone]

Web: www.adj.com / E-mail: [e-mail]

A.D.J. Supply Europe B.V.

Junostraat 2

6468 EW Kerkrade

Netherlands

[e-mail] / www.adj.eu

Tel: [phone] / Fax: [phone]