ADJ LED UV GO Operation Manual
LED UV GO Introduction
Unpacking: Thank you for purchasing the LED UV GO by ADJ Prod-
ucts, LLC. Every LED UV GO has been thoroughly tested and has been
shipped in perfect operating condition. Carefully check the shipping
carton for damage that may have occurred during shipping. If the
carton appears to be damaged, carefully inspect your xture for any
damage and be sure all accessories necessary to operate the unit has
arrived intact. In the case damage has been found or parts are missing, please contact our toll free customer support number for further
instructions. Do not return this unit to your dealer without rst contacting customer support.
Introduction: The LED UV GO is part of ADJ’s continuing pursuit for
creating high quality affordable fixtures. The LED UV GO is a UV LED
wash.
Customer Support: ADJ Products, LLC provides a toll free cus-
tomer support line, to provide set up help and to answer any question
should you encounter problems during your set up or initial operation.
You may also visit us on the web at www.adj.com for any comments
or suggestions. Service Hours are Monday through Friday 8:00 a.m. to
4:30 p.m. Pacic Standard Time.
Voice: (800) 322-6337
Fax: (323) 582-2941
E-mail: support@adj.com
1/13
Warning! To prevent or reduce the risk of electrical shock or re, do
not expose this unit to rain or moisture.
Caution! There are no user serviceable parts inside this unit. Do not
attempt any repairs yourself, doing so will void your manufactures warranty. In the unlikely event your unit may require service please contact
ADJ Products, LLC.
PLEASE recycle the shipping carton when ever possible.
User Instructions
ADJ Products, LLC - www.adj.com - LED UV GO Instruction Manual Page 2
LED UV GO General Instructions
LED UV GO Safety Precautions
To optimize the performance of this product, please read these operating instructions carefully to familiarize yourself with the basic operations
of this unit. These instructions contain important safety information
regarding the use and maintenance of this unit. Please keep this manual
with the unit, for future reference.
LED UV GO Features
• Adjustable Dimmer
• Strobing
• Battery Powered (Rechargeable Lithium Battery)
• Battery On/Off Switch On Rear Panel
• ADJ-RC1 Remote Included
LED UV GO Warranty Registration
The LED UV GO carries a 3 year (1095 days) limited warranty. Please
fill out the enclosed warranty card to validate your purchase and warranty. You may also register your product online at www. americandj.
com. All returned service items whether under warranty or not, must
be freight pre-paid and accompany a return authorization (R.A.) number. If the unit is under warranty you must provide a copy of your
proof of purchase invoice. Please contact ADJ customer support for a
R.A. number.
LED UV GO Installation
The unit should be mounted using a mounting clamp (not provided),
afxing it to the mounting bracket that is provided with the unit.
Always ensure that the unit is rmly xed to avoid vibration and slip-
ping while operating. Always ensure that the structure to which you
are attaching the unit is secure and is able to support a weight of 10
times the unit’s weight. Also, always use a safety cable that can hold
12 times the weight of the unit when installing the xture.
The equipment must be installed by a professional, and it must be
installed in a place where it is out of the reach of people’s grasp.
• To reduce the risk of electrical shock or re, do not expose this unit
rain or moisture
• Do not spill water or other liquids into or on to your unit.
• Do not attempt to operate this unit if the power cord has been
frayed or broken. Do not attempt to remove or break off the ground
prong from the electrical cord. This prong is used to reduce the risk
of electrical shock and re in case of an internal short.
• Disconnect from main power before making any type of connection.
• Do not remove the cover under any conditions. There are no user
serviceable parts inside.
• Never operate this unit when it’s cover is removed.
• Never plug this unit in to a dimmer pack
• Always be sure to mount this unit in an area that will allow proper
ventilation. Allow about 6” (15cm) between this device and a wall.
• Do not attempt to operate this unit, if it becomes damaged.
• This unit is intended for indoor use only, use of this product out`
doors voids all warranties.
• During long periods of non-use, disconnect the unit’s main power.
• Always mount this unit in safe and stable matter.
• Power-supply cords should be routed so that they are not likely to
be walked on or pinched by items placed upon or against them,
paying particular attention to the point they exit from the unit.
• Cleaning -The fixture should be cleaned only as recommended by
t he manufacturer. See page 12 for cleaning details.
• Heat -The appliance should be situated away from heat sources
such as radiators, heat registers, stoves, or other appliances (inclu d ing amplifiers) that produce heat.
• The fixture should be serviced by qualified service personnel when:
A. The power-supply cord or the plug has been damaged.
B. Objects have fallen, or liquid has been spilled into the appliance.
C. The appliance has been exposed to rain or water.
D. The appliance does not appear to operate normally or exhibits a
marked change in performance.
ADJ Products, LLC - www.adj.com - LED UV GO Instruction Manual Page 4ADJ Products, LLC - www.adj.com - LED UV GO Instruction Manual Page 3
LED UV GO System Menu LED UV GO System Menu
MENU
Dimmer Mode
Strobe Mode
Blackout mode
LED Display Always On
LED Display Off
Normal
Inversion
Battery state
On-Board System Menu.
navigate system menu. This next section will detail the functions of
each command in the system menu. Please read the next section
thoroughly!
To access the main menu press the MENU button. Tap the UP or
DOWN buttons until you reach function you wish to change. When you
reach the function you wish to change press the ENTER button. When
a function is selected use the UP or DOWN buttons to change the func-
tion settings. Once your changes are made press the ENTER button,
and then press and hold the MENU button for at least three seconds
to conrm and lock the change into the system memory. If the MENU
button is not pressed and held within eight seconds the xture will
automatically conrm and lock the change into the system memory. To
exit without making any changes press the MENU button.
The LED UV GO comes with an easy to
DIMM - Dimmer Mode
1. Press the MENU button until “DINN” is displayed, press
ENTER.
2. “dXXX” will now be displayed, “XXX” representing a number
between 0-255. Use the UP of DOWN buttons to adjust the
output intensity.
Fixture Hours
ADJ Products, LLC - www.adj.com - LED UV GO Instruction Manual Page 5
3. Once you have found your desired intensity, press ENTER to
conrm.
STRO - Strobe mode
1. Press the MENU button until “STRO” is displayed, press
ENTER.
2. “SP X” will now be displayed, “X” representing a number
between 1-9. These are the strobe speeds, 1 being the slowest,
and 9 being the fastest. Use the UP and DOWN buttons to adjust
the strobe speed.
3. Press ENTER to conrm.
ADJ Products, LLC - www.adj.com - LED UV GO Instruction Manual Page 6
Loading...