Inno Pocket Spot Pearl
©2014 ADJ Products, LLC all rights reserved. Information,
specications, diagrams, images, and instructions herein are
subject to change without notice. ADJ Products, LLC logo and
identifying product names and numbers herein are trademarks
of ADJ Products, LLC. Copyright protection claimed includes all
forms and matters of copyrightable materials and information
now allowed by statutory or judicial law or hereinafter granted.
Product names used in this document may be trademarks or
registered trademarks of their respective companies and are
hereby acknowledged. All non-ADJ Products, LLC brands and
product names are trademarks or registered trademarks of their
respective companies.
ADJ Products, LLC and all aliated companies hereby disclaim any and all liabilities for property, equipment, building,
and electrical damages, injuries to any persons, and direct or
indirect economic loss associated with the use or reliance of
any information contained within this document, and/or as a
result of the improper, unsafe, unsucient and negligent assembly, installation, rigging, and operation of this product.
Rev. 10/14
User Instructions
Europe Energy Saving Notice
Energy Saving Matters (EuP 2009/125/EC)
Saving electric energy is a key to help protecting the enviroment.
Please turn o all electrical products when they are not in use. To
avoid power consumption in idle mode, disconnect all electrical
equipment from power when not in use. Thank you!
Inno Pocket Spot Pearl General Information
Inno Pocket Spot Pearl General Instructions
Unpacking: Thank you for purchasing the Inno Pocket Spot Pearl by
ADJ Products, LLC. Every Inno Pocket Spot Pearl has been thoroughly
tested and has been shipped in perfect operating condition. Carefully
check the shipping carton for damage that may have occurred during
shipping. If the carton appears to be damaged, carefully inspect your
xture for any damage and be sure all equipment necessary to operate the unit has arrived intact. In the event damage has been found
or parts are missing, please contact our toll free customer support
number for further instructions. Please do not return this unit to your
dealer without contacting customer support rst.
Introduction: The Inno Pocket Spot Pearl is a DMX intelligent, moving
head, mini LED fixture. The Inno Pocket Spot Pearl can operate as a
stand alone fixture or in a Master/Slave configuration. The Inno Pocket
Spot Pearl has three operating modes; a sound active, show mode,
DMX controlled. This fixture is suitable for theaters, studios, retail
stores, and other similar locations. For best results use fog or special
effects smoke to enhance the beams projections.
Customer Support: ADJ Products, LLC provides a toll free cus-
tomer support line, to provide help and to answer any question should
you encounter problems during your set up or initial operation. You
may also visit us on the web at www.adj.com for any comments or
suggestions. Service Hours are Monday through Friday 8:00 a.m. to
4:30 p.m. Pacic Standard Time.
Voice: (800) 322-6337
Fax: (323) 582-2941
E-mail: support@americandj.com
Warning! To prevent or reduce the risk of electrical shock or re, do
not expose this unit to rain or moisture.
Warning! This may cause severe eye damage. Avoid looking directly
into the light source at all times!
To optimize the performance of this product, please read these
operating instructions carefully to familiarize yourself with the basic
operations of this unit. These instructions contain important safety
information regarding the use and maintenance of this unit. Please
keep this manual with the unit, for future reference.
Inno Pocket Spot Pearl Features
• DMX-512 Protocol Compatible (9 DMX Channels or 11 Channels)
• 7 Colors + White
• Fixed Gobo Wheel with 7 Gobos + Spot
• 3 Operating Modes - Sound Active, Show Mode, & DMX Control
• Internal Microphone
• Digital Display for Address and Function Setting
• 4 Preprogrammed Shows
• UC-IR Compatiable (Not Included)
Inno Pocket Spot Pearl Warranty Registration
The Inno Pocket Spot Pearl carries a 2 year (730 days) limited war-
ranty. Please fill out the enclosed warranty card to validate your
purchase and warranty. You may also register your product online
at www. adjproducts.com. All returned service items whether under
warranty or not, must be freight pre-paid and accompany a return
authorization (R.A.) number. If the unit is under warranty you must
provide a copy of your proof of purchase invoice. Please contact ADJ
Products, LLC customer support for a R.A. number.
Inno Pocket Spot Pearl Handling Precautions
Caution! There are no user serviceable parts inside this unit. Do not
attempt any repairs yourself, doing so will void your manufactures
warranty. In the unlikely event your unit may require service please
contact ADJ Products, LLC.
During operation the housing may become extremely hot. Avoid
touching the unit with bare hands while in use.
ADJ Products, LLC will not accept any liability for any resulting damages caused by the non-observance of this manual or any unauthor-
ized modication to this unit.
ADJ Products, LLC - www.adj.com - Inno Pocket Spot Pearl Instruction Manual Page 3ADJ Products, LLC - www.adj.com - Inno Pocket Spot Pearl Instruction Manual Page 2
Inno Pocket Spot Pearl Safety Precautions
Inno Pocket Spot Pearl Mounting
For Your Own Personal Safety, Please Read and Understand This
Manual Completely Before You Attempt To Install Or Operate
This Unit!
• To reduce the risk of electrical shock or re, do not expose this unit
rain or moisture
• Do not spill water or other liquids into or on to your unit.
• Be sure that the local power outlet match that of the required volt age for your unit.
• Do not attempt to operate this unit if the power cord has been
frayed or broken.
• Do not attempt to remove or break o the ground prong from
the electrical cord. This prong is used to reduce the risk of electrical
shock and re in case of an internal short.
• Disconnect from main power before making any type of connection.
• Do not remove the cover under any conditions. There are no user
serviceable parts inside.
• Never operate this unit when it’s cover is removed.
• Always be sure to mount this unit in an area that will allow proper
ventilation. Allow about 6” (15cm) between this device and a wall.
• Do not attempt to operate this unit, if it becomes damaged.
• This unit is intended for indoor use only, use of this product out doors voids all warranties.
• Always mount this unit in safe and stable matter.
• Power-supply cords should be routed so that they are not likely to
be walked on or pinched by items placed upon or against them,
paying particular attention to cords at plugs, convenience recep tacles, and the point where they exit from the appliance.
• Cleaning -The fixture should be cleaned only as recommended by
the manufacturer. See page 25 for cleaning details.
• Heat -This fixture should be situated away from heat sources such
as radiators, heat registers, stoves, or other appliances (including
amplifiers) that produce heat.
• The fixture should be serviced by qualified service personnel when:
A. Objects have fallen, or liquid has been spilled into the appliance.
B. The appliance has been exposed to rain or water.
C. The appliance does not appear to operate normally or exhibits
a marked change in performance.
When installing the unit, the trussing or area of installation must be
able to hold 10 times the weight without any deformation. When
installing the unit must be secured with a secondary safety attachment, e.g. and appropriate safety cable. Never stand directly below
the unit when mounting, removing, or servicing the unit.
Overhead mounting requires extensive experience, including calculating working load limits, installation material being used, and perodic
safety inspection of all installation material and unit. If you lack these
qualications, do not attempt the installation yourself.
The installaiton should be checked by a skilled person once a year.
The Inno Pocket Spot Pearl is fully operational in two dierent mounting positions, hanging upside-down from a ceiling or set on a at
level surface. To avoid internal damage to the unit, never mount the
unit on its side as illustrated above. Be sure this xture is kept at least
0.5m away from any ammable materials (decoration etc.). Always
use and install the supplied safety cable as a safety measure to prevent accidental damage and/or injury in the event the clamp fails (see
next page).
ADJ Products, LLC - www.adj.com - Inno Pocket Spot Pearl Instruction Manual Page 5ADJ Products, LLC - www.adj.com - Inno Pocket Spot Pearl Instruction Manual Page 4
Inno Pocket Spot Pearl Mounting
Inno Pocket Spot Pearl DMX Set Up
NOTICE: The suitable enviromental temperature for this light-
ing xture is between -25˚ C to 45˚ C. Do not place this lighting
xture in an enviroment where the temperatures are under or
above the temperatures stated above. This will allow the xture
to run at its best and help prolong the xture life.
Power Supply: The ADJ Inno Pocket Spot Pearl contains a automatic
voltage switch, which will auto sense the voltage when it is plugged
into the power source. With this switch there is no need to worry about
the correct power voltage, this unit can be plugged in anywhere.
DMX-512: DMX is short for Digital Multiplex. This is a universal pro-
tocol used by most lighting and controller manufactures as a form of
communication between intelligent fixtures and controllers. A DMX
controller sends DMX data instructions from the controller to the fixture. DMX data is sent as serial data that travels from fixture to fixture
via the DATA “IN” and DATA “OUT” XLR terminals located on all DMX
fixtures (most controllers only have a DATA “OUT” terminal).
DMX Linking: DMX is a language allowing all makes and models
of dierent manufactures to be linked together and operate from a
single controller, as long as all xtures and the controller are DMX
compliant. To ensure proper DMX data transmission, when using
several DMX fixtures try to use the shortest cable path possible. The
order in which fixtures are connected in a DMX line does not influence
the DMX addressing. For example; a fixture assigned a DMX address
of 1 may be placed anywhere in a DMX line, at the beginning, at the
end, or anywhere in the middle. Therefore, the first fixture controlled
by the controller could be the last fixture in the chain. When a fixture
is assigned a DMX address of 1, the DMX controller knows to send
DATA assigned to address 1 to that unit, no matter where it is located
in the DMX chain.
Data Cable (DMX Cable) Requirements (For DMX and Master/Slave
Operation): The Inno Pocket Spot Pearl can be controlled via DMX-
512 protocol. The Inno Pocket Spot Pearl two DMX channel modes;
9 channel mode & 11 channel mode. The DMX
Screw one clamp via a M12 screw and nut to the included
bracket. Attach the bracket using the included screws to the
bottom of the Inno Pocket Spot Pearl. Attach the eyehole screw
to the bottom of the base and pull the safety-cable through
the screw and over the trussing system or a safe xation spot.
Insert the end in the carabine and tighten the safety screw.
ADJ Products, LLC - www.adj.com - Inno Pocket Spot Pearl Instruction Manual Page 6 ADJ Products, LLC - www.adj.com - Inno Pocket Spot Pearl Instruction Manual Page 7
address is set electronically using the controls on
the front panel of the unit. Your unit and your DMX
controller require a approved DMX-512 110 Ohm
Data cable for data input and data output (Figure
1). We recommend Accu-Cable DMX cables. If you
are making your own cables, be sure to use standard 110-120 Ohm shielded cable (This cable may
be purchased at almost all professional sound and
Figure 1
Inno Pocket Spot Pearl DMX Set Up
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
DMX512
DMX+,DMX-,COMMON
1
2
3
Termination reduces signal errors and
avoids signal transmission problems
and interference. It is always advisable
to connect a DMX terminal, (Resistance
120 Ohm 1/4 W) between PIN 2 (DMX-)
and PIN 3 (DMX +) of the last fixture.
POWER
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
Inno Pocket Spot Pearl DMX Set Up
lighting stores). Your cables should be made with a male and female
XLR connector on either end of the cable. Also remember that DMX
cable must be daisy chained and cannot be split.
Notice: Be sure to follow gures two and three when making your own
cables. Do not use the ground lug on the XLR connector. Do not connect the cable’s shield conductor to the ground lug or allow the shield
conductor to come in contact with the XLR’s outer casing. Grounding
the shield could cause a short circuit and erratic behavior.
COMMON
1
DMX512 IN
3
3-PIN XLR
2
Figure 2
XLR Pin Conguration
Pin 1 = Ground
Pin 2 = Data Compliment (negative)
Pin 3 = Data True (positive)
XLR Male Socket
1 Ground
Figure 3
DMX512 OT
3-PIN XLR
2 Cold
3 Hot
1
3
2
XLR Female Socket
2 Cold
DMX +
DMX -
1 Ground
3 Hot
5-Pin XLR DMX Connectors.
Some manufactures use 5-pin DMX-
512 data cables for DATA transmission in place of 3-pin. 5-pin DMX
xtures may be implemented in a 3-pin DMX line. When inserting standard 5-pin data cables in to a 3-pin line a cable adaptor must be used,
these adaptors are readily available at most electric stores. The chart
below details a proper cable conversion.
3-Pin XLR to 5-Pin XLR Conversion
Conductor 5-Pin XLR Male (In)3-Pin XLR Female (Out)
Ground/Shield
Data Compliment (- signal)
Data True (+ signal)
Not Used
Not Used
Pin 1
Pin 2
Pin 3
Pin 1
Pin 2
Pin 3
Pin 4 - Do Not Use
Pin 5 - Do Not Use
Special Note: Line Termination.
used, you may need to use a terminator on the last unit to avoid erratic
behavior. A terminator is a 110-120 ohm 1/4 watt resistor which is con-
When longer runs of cable are
nected between pins 2 and 3 of a male XLR connector (DATA + and
DATA -). This unit is inserted in the female XLR connector of the last
unit in your daisy chain to terminate the line. Using a cable terminator
(ADJ part number Z-DMX/T) will decrease the possibilities of erratic
behavior.
Termination reduces signal errors and
1
avoids signal transmission problems
3
and interference. It is always advisable
2
to connect a DMX terminal, (Resistance
120 Ohm 1/4 W) between PIN 2 (DMX-)
and PIN 3 (DMX +) of the last fixture.
Figure 4
ADJ Products, LLC - www.adj.com - Inno Pocket Spot Pearl Instruction Manual Page 9ADJ Products, LLC - www.adj.com - Inno Pocket Spot Pearl Instruction Manual Page 8
Inno Pocket Spot Pearl System Menu
g
Sho w Mo de
Slave M od e
Los t DM X Signa l
Sou nd S en se
Pan Inv er se
Di splay N ormal
Di splay I nv ersio n
DMX 512 Ad dr ess Set tin
Channel M ode
Dim me r Mod e
Sou nd M ode
Inno Pocket Spot Pearl System Menu
System Menu: When making adjustments press ENTER to
conrm your setup then press and hold the MENU button
for at least 3 seconds. To exit without making any adjust-
ments press the MENU button. The display will lock after 30
seconds, press the MENU button for 3 seconds to unlock.
ADDR - DMX Address Setting.
1. Press the either the MENU, UP, or DOWN buttons until “ADDR” is
displayed, press ENTER.
2. The current address will now be displayed and ashing. Press the
UP or DOWN buttons to nd your desired address. Press ENTER to
set your desired DMX address.
CHND - This will let select your desired DMX channel
mode.
1. Press the either the MENU button until “CHND” is displayed, press
ENTER. Either “9CH” or “11CH” will be displayed
2. Press the UP or DOWN buttons to nd your desired DMX channel
mode and press ENTER to conm and exit.
ADJ Products, LLC - www.adj.com - Inno Pocket Spot Pearl Instruction Manual Page 10
SHND - Show modes 0-4 (Factory programs). Show
mode can run with or without sound active mode active.
1. Press the MENU button until “SHND” is displayed, press ENTER.
Til t Inverse
LED Dis play
Aut o Test
Fi xtu re U se Ti me
Fi rmwar e Version
Res et
2. “Sh X” will now be displayed, “X” representing a number between
0-4. Shows 1-4 are factory programs, while show “0” is random mode.
Use the UP or DOWN buttons to nd your desired show.
3. When you have found your desired show press ENTER, then press
and hold the MENU button for at least 3 seconds to activate. After
you have set your desired show, it can be changed at any time using
the UP or DOWN buttons.
DIND - This will let select your desired dimmer curve.
ADJ Products, LLC - www.adj.com - Inno Pocket Spot Pearl Instruction Manual Page 11
Inno Pocket Spot Pearl System Menu
Inno Pocket Spot Pearl System Menu
1. Press the either the MENU button until “DIND” is displayed, press
ENTER. 1 of 5 dimmer curves will be displayed. “STDA” (standard),
“STGE” (stage), “TV” (TV), “ARAL” (theatrical), or “THAL” (Architectural).
2. Press the UP or DOWN buttons to nd your desired dimmer curve
and press ENTER to conm and exit.
will automatically go into show mode.
• BLAC (Blackout) - If the DMX signal is lost or interrupted, the unit will
automatically go into stand by mode.
3. Press ENTER to conrm your desired set up.
SOUN - Sound Active mode.
SLND - This will let you set unit as a master or slave in a
master/slave conguration.
1. Press the MENU button until “SLND” is displayed, press ENTER.
Either “MAST”, “SL 1”, or “SL 2” will be displayed.
2. Press the UP or DOWN buttons until your desired setting is displayed, press ENTER to conm.
NOTE: In a Master/Slave conguration you can set one xture to
Master and then set the next xture to “SL 2”, the xtures will now
have contrast movement to each other.
LOST - This mode can be used as a precaution mode, that
in case the DMX signal is lost, interrupted, or power is lost,
the operating mode chosen in the setup is the running mode
the xture will go into when the DMX signal is lost. You can
also set this as the operating mode you would like the unit to
return to when power is applied.
1. Press the MENU button until “LOST” is displayed, and either
“HOLD”, “SHND”, or “BLAC” will be displayed beneath.
2. Press ENTER and the bottom choice will begin to ash. Use the UP
or DOWN buttons to choose an operating mode you would like the unit
to start up in when power is applied or the DMX signal is lost.
• Hold - If the DMX signal is lost the xture will stay in the last DMX setting. If power is applied and this mode is set, the unit will automatically
go into the last DMX set up.
• SHND (Show Mode) - If the DMX signal is lost, interrupted, the unit
ADJ Products, LLC - www.adj.com - Inno Pocket Spot Pearl Instruction Manual Page 12 ADJ Products, LLC - www.adj.com - Inno Pocket Spot Pearl Instruction Manual Page 13
1. Press the MENU button until “SOUN” is displayed, press ENTER.
2. The display will show either “ON” or “OFF”. Press the UP or
DOWN buttons to select “ON” to activate sound active mode, or
“OFF” to deactivate sound active mode.
3. Press ENTER to conrm.
SENS - In this mode you can adjust the sound sensitiv-
ity.
1. Press the MENU button until “SENS” is displayed, press ENTER.
2. A number between 0-100 will be displayed. Press the UP or DOWN
buttons to adjust the sound sensitivity. 0 being the least sensitive,
and 100 being the most sensitive.
3. When you have found your desired setting press ENTER to conrm.
PINT - Pan Inversion
1. Press the MENU button until “PINT” is displayed, press ENTER.
Either “Yes” or “No” will be displayed.
2. To activate the Pan inversion press the UP or DOWN buttons until
“Yes” is displayed, press ENTER to conm. To deactivate Pan inversion, select “No” and press Enter.
TINT - Tilt Inversion
1. Press the MENU button until “TINT” is displayed, press ENTER.
Either “Yes” or “No” will be displayed.
Inno Pocket Spot Pearl System Menu
Inno Pocket Spot Pearl System Menu
2. To activate the tilt inversion press the UP or DOWN buttons until
“Yes” is displayed, press ENTER to conm. To deactivate tilt inversion, select “No” and press Enter.
LED - With this function you can have the LED display
turn off after 10 seconds.
1. Press the MENU button until “LED” is displayed, press ENTER.
2. The display will show either “ON” or “OFF”. Press the UP or
DOWN buttons to select “ON” to keep the LED display on at all
times, or “OFF” to switch to have the LED display switch o after 10
seconds.
3. Press ENTER to conrm. To make you LED display reappear again
press any button.
DISP - This function will reverse the display 180º.
1. Press the MENU button until “DISP” is displayed, press ENTER.
2. Press ENTER to “ip” the display. Press ENTER to “ip” it again.
Press ENTER when you have made your desired setup.
the unit.
1. Press the either the MENU button until “VER” is displayed, press
ENTER.
2. The display will show the software version.
RSET - Use this function to reset the unit.
1. Press the MENU button until “RSET” is displayed, press ENTER.
2. The xture will now reset.
Inno Pocket Spot Pearl Home Adjustment Menu
TEST - This function will run a self test program.
1. Press the MENU button until “TEST” is displayed, press ENTER.
2. The xture will now run a self test.
FHRS - With this function you can display the running
time of the unit.
1. Press the MENU button until “FHRS” is displayed, press ENTER.
2. The running time of the xture will now be displayed. Press MENU
to exit.
VER - Use this function to display the Software version of
To enter the home position adjustment menu, press the ENTER
button for at least 5 seconds. In this submenu you are able to adjust
the original position of the pan position, tilt position, color wheel position, and gobo wheel position.
OPAN - Adjustment of the pan position.
1. Press the ENTER button for at least 5 seconds, then press the UP
or DOWN buttons so that “OPAN” is displayed, press ENTER.
2. Use the UP and DOWN buttons to make your adjustments, and
then press ENTER to conrm. Press the MENU button for one second
to exit.
ADJ Products, LLC - www.adj.com - Inno Pocket Spot Pearl Instruction Manual Page 15ADJ Products, LLC - www.adj.com - Inno Pocket Spot Pearl Instruction Manual Page 14
Inno Pocket Spot Pearl Operation Inno Pocket Spot Pearl Home Adjustment Menu
OTIL - Adjustment of the tilt position.
1. Press the ENTER button for at least 5 seconds, then press the UP
or DOWN buttons so that “OTIL” is displayed, press ENTER.
2. Use the UP and DOWN buttons to make your adjustments, and
then press ENTER to conrm. Press the MENU button for one second
to exit.
OGOB - Adjustment of the gobo wheel.
1. Press the ENTER button for at least 5 seconds, then press the UP
or DOWN buttons so that “OGOB” is displayed, press ENTER.
2. Use the UP and DOWN buttons to make your adjustments, and
then press ENTER to conrm. Press the MENU button for one second
to exit.
OCOL - Adjustment for the color wheel.
1. Press the ENTER button for at least 3 seconds, then press the UP
or DOWN buttons so that “OCOL” is displayed, press ENTER.
2. Use the UP and DOWN buttons to make your adjustments, and
then press ENTER to conrm. Press the MENU button for one second
to exit.
Universal DMX Control: This function allows you to use a Elation®
universal DMX-512 controller to control the chases and patterns,
dimmer and strobe. A DMX controller allows you to create unique
programs tailored to your individual needs.
1. The Inno Pocket Spot Pearl has 2 DMX channel modes; 9 channel
mode or 11 channel mode. See pages 20-23 for detailed descrip tion of the DMX values and traits.
2. To control your fixture in DMX mode, follow the set-up procedures
on pages 5-7 as well as the set-up specifications that are includ ed with your DMX controller.
3. Use the controller’s faders to control the various DMX fixture traits.
4. This will allow you to create your own programs.
5. Follow the instruction on page 9 to set the DMX address.
6. For longer cable runs (more than a 100 feet) use a terminator on
the last fixture.
7. For help operating in DMX mode consult the manual included
with your DMX controller.
Sound Active Mode: This mode allows either single unit or several
units linked together, to run to the beat of the music.
1. Press the MENU button until “SOUN” is displayed, and press
ENTER. Press the UP or DOWN buttons so that “ON” is dis-
played and press ENTER.
2. Press the MENU button until “SENS” is displayed, and press
ENTER. Use the UP and DOWN buttons to adjust the sound
sensitivity. Press ENTER when you have found your desired sensi-
tivity level.
Show Mode: This mode allows either a single unit or several units
linked together, to run one of four shows that you choose.
1. Press the MENU button until “SHND” is displayed, and press
ENTER.
2. Press the UP or DOWN buttons until you nd your desired show,
and press ENTER.
ADJ Products, LLC - www.adj.com - Inno Pocket Spot Pearl Instruction Manual Page 16 ADJ Products, LLC - www.adj.com - Inno Pocket Spot Pearl Instruction Manual Page 17
Inno Pocket Spot Pearl Remote Operation Inno Pocket Spot Pearl Master-Slave Set Up
Master-Slave Operation This function will allow you to link up to 16
units together and operate without a controller. The units will be sound
activated. In Master-Slave operation one unit will act as the controlling
unit and the others will react to the controlling units programs. Any unit
can act as a Master or as a Slave.
1. Using approved DMX data cables, daisy chain your units togeth-
er via the XLR connector on the rear of the units. Remember the
Male XLR connector is the input and the Female XLR connector
is the output. The rst unit in the chain (master) will use the female
XLR connector only - The last unit in the chain will use the male
XLR connector only. For longer cable runs we suggest a termina tor at the last fixture.
2. On the Master unit press the MENU button until “SLND” is dis played, and press ENTER. Use the UP and DOWN buttons to
scroll to the “MAST” setting and press ENTER.
3. After setting the Master unit to the master setting find your
desired operating mode.
4. On the slave units press the MENU button until “SLND” is dis played, and press ENTER. Choose either “SL 1” or “SL 2” and
press ENTER. See page 10 for more info.
5. The slave units will now follow the Master unit.
The UC-IR infrared remote gives you control of various functions
(See below). To control the fixture you must aim the remote at the
front of the fixture and be no more then 30 feet away.
STAND BY - Pressing this button will blackout the fixture.
FULL ON - Hold this button down to fully light up the unit. When you
let the button go, the unit will return to its previous state.
FADE/GOBO - Press this button to enter Gobo mode. Use the 1-9
buttons to select your desired gobo. Adjust the output intensity using
the “DIMMER +” and “DIMMER -” buttons.
“DIMMER +” and “DIMMER -” - Use these buttons to adjust the output intensity and to adjust the strobe speed.
STROBE - This button will activate the strobe effect. You can control
the flash rate by pressing the “DIMMER +” and “DIMMER -” buttons.
If you press and hold this button the unit will begin to strobe.
COLOR - Press this button to enter Dimmer mode. Use the 1-9 but-
tons to select your desired color. Adjust the output intensity using the
“DIMMER +” and “DIMMER -” buttons.
1-9 - When in either Gobo mode or Color mode, these buttons will
allow you to select either a gobo or color.
SOUND ON & OFF - These buttons activate and deactivate the
sound active mode.
SHOW -
This activates the show mode. Use the “DIMMER +” and
“DIMMER -” buttons to scroll through the 4 shows.
ADJ Products, LLC - www.adj.com - Inno Pocket Spot Pearl Instruction Manual Page 18 ADJ Products, LLC - www.adj.com - Inno Pocket Spot Pearl Instruction Manual Page 19
Inno Pocket Spot Pearl 9 Channel Mode
Inno Pocket Spot Pearl 9 Channel Mode
Channel Value Function
1 0 - 255 PAN MOVEMENT 8bit
2 0 - 255 TILT MOVEMENT 8bit
3 COLORS
0 - 7 WHITE
8 - 14 RED
15 - 21 ORANGE
22 - 28 YELLOW
29 - 35 GREEN
36 - 42 BLUE
43 - 49 LIGHT BLUE
50 - 56 PINK
57 - 127 SPLIT COLORS
128 - 189 COLOR SCROLL FAST - SLOW
190 - 193 STOP
194 - 255 COLOR SCROLL SLOW - FAST
4 GOBO WHEEL
0 - 7 OPEN
8 - 15 GOBO 1
16 - 23 GOBO 2
24 - 31 GOBO 3
32 - 39 GOBO 4
40 - 47 GOBO 5
48 - 55 GOBO 6
56 - 63 GOBO 7
64 - 71 OPEN SHAKE
72 - 79 GOBO 1 SHAKE
80 - 87 GOBO 2 SHAKE
88 - 95 GOBO 3 SHAKE
96 - 103 GOBO 4 SHAKE
104 - 111 GOBO 5 SHAKE
112 - 119 GOBO 6 SHAKE
120 - 127 GOBO 7 SHAKE
128 - 189 GOBO SCROLL FAST - SLOW
190 - 193 STOP
194 - 255 GOBO SCROLL SLOW - FAST
Channel Value Function
5 SHUTTER/STROBE
0 - 7 BLACKOUT
8 - 15 SHUTTER OPEN
16 - 131 STROBING SLOW - FAST
132 - 139 SHUTTER OPEN
140 - 181 SHUTTER SLOW OPEN - FAST CLOSE
182 - 189 SHUTTER OPEN
190 - 231 SHUTTER FAST OPEN - SLOW CLOSE
232 - 239 SHUTTER OPEN
240 - 247 RANDOM STROBE
248 - 255 SHUTTER OPEN
6 0 - 255 DIMMER 0% - 100%
7 0 - 255 MOVEMENT SPEED FAST - SLOW
8 FUNCTION
0 - 69 NO FUNCTION
70 - 79 BLACKOUT WITH PAN/TILT
80 - 89 NO FUNCTION
90 - 99 BLACKOUT WITH COLOR CHANGE
100 - 109 NO FUNCTION
110 - 119 BLACKOUT WITH GOBO CHANGE
120 - 199 NO FUNCTION
200 - 209 RESET ALL
210 - 249 NO FUNCTION
250 - 255 SOUND ACTIVE MODE
9 DIMMER CURVES
0 - 20 STANDARD
21 - 40 STAGE
41 - 60 TV
61 - 80 ARCHITECTURAL
81 - 100 THEATER
101 - 255 DEFAULT TO UNIT CURVE SETTING
ADJ Products, LLC - www.adj.com - Inno Pocket Spot Pearl Instruction Manual Page 20 ADJ Products, LLC - www.adj.com - Inno Pocket Spot Pearl Instruction Manual Page 21
Inno Pocket Spot Pearl 11 Channel Mode
Inno Pocket Spot Pearl 11 Channel Mode
Channel Value Function
1 0 - 255 PAN MOVEMENT 8bit
2 0 - 255 PAN FINE 16bit
3 0 - 255 TILT MOVEMENT 8bit
4 0 - 255 TILT FINE 16bit
5 COLORS
0 - 7 WHITE
8 - 14 RED
15 - 21 ORANGE
22 - 28 YELLOW
29 - 35 GREEN
36 - 42 BLUE
43 - 49 LIGHT BLUE
50 - 56 PINK
57 - 127 SPLIT COLORS
128 - 189 COLOR SCROLL FAST - SLOW
190 - 193 STOP
194 - 255 COLOR SCROLL SLOW - FAST
6 GOBO WHEEL
0 - 7 OPEN
8 - 15 GOBO 1
16 - 23 GOBO 2
24 - 31 GOBO 3
32 - 39 GOBO 4
40 - 47 GOBO 5
48 - 55 GOBO 6
56 - 63 GOBO 7
64 - 71 OPEN SHAKE
72 - 79 GOBO 1 SHAKE
80 - 87 GOBO 2 SHAKE
88 - 95 GOBO 3 SHAKE
96 - 103 GOBO 4 SHAKE
104 - 111 GOBO 5 SHAKE
112 - 119 GOBO 6 SHAKE
120 - 127 GOBO 7 SHAKE
128 - 189 GOBO SCROLL FAST - SLOW
Channel Value Function
6 190 - 193 STOP
194 - 255 GOBO SCROLL SLOW - FAST
7 SHUTTER/STROBE
0 - 7 BLACKOUT
8 - 15 SHUTTER OPEN
16 - 131 STROBING SLOW - FAST
132 - 139 SHUTTER OPEN
140 - 181 SHUTTER SLOW OPEN - FAST CLOSE
182 - 189 SHUTTER OPEN
190 - 231 SHUTTER FAST OPEN - SLOW CLOSE
232 - 239 SHUTTER OPEN
240 - 247 RANDOM STROBE
248 - 255 SHUTTER OPEN
8 0 - 255 DIMMER 0% - 100%
9 0 - 255 MOVEMENT SPEED FAST - SLOW
10 FUNCTION
1 - 69 NO FUNCTION
70 - 79 BLACKOUT WITH PAN/TILT
80 - 89 NO BLACKOUT WITH PAN/TILT
90 - 99 BLACKOUT WITH COLOR CHANGE
100 - 109 NO BLACKOUT WITH COLOR CHANGE
110 - 119 BLACKOUT WITH GOBO CHANGE
120 - 129 NO BLACKOUT WITH GOBO CHANGE
130 - 199 NO FUNCTION
200 - 209 RESET ALL
210 - 249 NO FUNCTION
250 - 255 SOUND ACTIVE MODE
11 DIMMER CURVES
0 - 20 STANDARD
21 - 40 STAGE
41 - 60 TV
61 - 80 ARCHITECTURAL
81 - 100 THEATER
101 - 255 DEFAULT TO UNIT CURVE SETTING
ADJ Products, LLC - www.adj.com - Inno Pocket Spot Pearl Instruction Manual Page 23ADJ Products, LLC - www.adj.com - Inno Pocket Spot Pearl Instruction Manual Page 22
Inno Pocket Spot Pearl Photometric Chart
R
G
B
1458 417
154
115
82
2790
780 356 207 143
425
123 58 36
28
RGBW
1m 2m 3m 4m 5m
4500
1280 584 339 227
1.0 2.0 3.0 4.0
Distance(m)
0
0m( )
5.0
60
0m( )
30900 10920 4916 2085
1788
17
1213
INNO POCKET SPOT
1.0 2.0 3.0 4.0
Distance(m)
0
0m( )
159000 75300 40060 19930
5.0
14470
6
6.0
9800
INNO BEAM LED
0m( )
6.0
Distance(m)
13
0
1.0 2.0 3.0 4.0
5.0
Inno Pocket Spot Pearl Fuse Replacement
Locate and remove the unit’s power cord. Once the cord has been
removed located the fuse holder located inside the power socket.
Insert a flat-head screw driver into the power socket and gently pry
out the fuse holder. Remove the bad fuse and replace with a new one.
The fuse holder has a built-in socket for a spare fuse be sure not to
confuse the spare fuse with active fuse.
Inno Pocket Spot Pearl Cleaning
Inno Pocket Spot Pearl Dimmer Curve Chart
Ramp Effect
Standard
Stage
TV
Architectural
Theatre
(Fade Time) (Fade Time)
Due to fog residue, smoke, and dust cleaning the internal and external optical lenses and mirror should be carried out periodically to
optimize light output. Cleaning frequency depends on the environment in which the fixture operates (I.e. smoke, fog residue, dust,
dew). In heavy club use we recommend cleaning on a monthly basis.
Periodic cleaning will ensure longevity, and crisp output.
1. Use normal glass cleaner and a soft cloth to wipe down the out-
side casing.
2. Use a brush to wipe down the cooling vents and fan grill.
3. Clean the external optics with glass cleaner and a soft cloth every
20 days.
4. Clean the internal optics with glass cleaner and a soft cloth every
30-60 days.
5. Always be sure to dry all parts completely before plugging the unit
back in.
Inno Pocket Spot Pearl Trouble Shooting
Trouble Shooting: Listed below are a few common problems that
you may encounter, with solutions.
No light output from the unit;
1. Be sure the external fuse has not blown. The fuse is located on
the rear panel of the unit.
2. Be sure the fuse holder is completely and properly seated.
Unit does not respond to sound;
1. Low frequencies (bass) should cause the unit to react to sound.
Tapping on the microphone, quiet or high pitched sounds may
ADJ Products, LLC - www.adj.com - Inno Pocket Spot Pearl Instruction Manual Page 24 ADJ Products, LLC - www.adj.com - Inno Pocket Spot Pearl Instruction Manual Page 25
not activate the unit.
Inno Pocket Spot Pearl Warranty
MANUFACTURER’S LIMITED WARRANTY
A. ADJ Products, LLC hereby warrants, to the original purchaser, ADJ Products, LLC products
to be free of manufacturing defects in material and workmanship for a prescribed period from
the date of purchase (see specific warranty period on reverse). This warranty shall be valid only if the
product is purchased within the United States of America, including possessions and
territories. It is the owner’s responsibility to establish the date and place of purchase by acceptable
evidence, at the time service is sought.
B. For warranty service you must obtain a Return Authorization number (RA#) before sending back
the product–please contact ADJ Products, LLC Service Department at 800-322-6337. Send the pro duct only to the ADJ Products, LLC factory. All shipping charges must be pre-paid. If the requested
repairs or service (including parts replacement) are within the terms of this warranty, ADJ Products, LLC
will pay return shipping charges only to a designated point within the United States. If the entire instru ment is sent, it must be shipped in it’s original package. No accessories should be shipped with the product.
If any accessories are shipped with the product, ADJ Products, LLC shall have no liability whatsoever for
loss of or damage to any such accessories, nor for the safe return thereof.
C. This warranty is void if the serial number has been altered or removed; if the product is modified in any
manner which ADJ Products, LLC concludes, after inspection, affects the reliability of the product; if the
product has been repaired or serviced by anyone other than the ADJ Products, LLC factory unless prior
written authorization was issued to purchaser by ADJ Products, LLC; if the product is damaged because
not properly maintained as set forth in the instruction manual.
D. This is not a service contract, and this warranty does not include maintnance, cleaning or periodic check
up. During the period specified above, ADJ Products, LLC will replace defective parts at its expense
with new or refurbished parts, and will absorb all expenses for warranty service and repair labor by
reason of defects in material or workmanship. The sole responsibility of ADJ Products, LLC under this
warranty shall be limited to the repair of the product, or replacement thereof, including parts, at the sole
discretion of ADJ Products, LLC. All products covered by this warranty were manufactured after August
15, 2012, and bear indentifying marks to that effect.
E. ADJ Products, LLC reserves the right to make changes in design and/or improvements upon its products
without any obligation to include these changes in any products theretofore manufactured.
Inno Pocket Spot Pearl Specifications
Model: Inno Pocket Spot Pearl
Voltage: 100 - 240V, 50/60Hz
LED: 1 x 12W White LED
Power Consumption: 26W @ 120V
27W @ 230V
Dimensions: 6.25”(L) x 5.75”(W) x 10.5”(H)
159mm x 147mm x 265mm
Weight: 7 Lbs. / 3 kgs.
Beam Angle: 13 Degrees
Fuse: 2 Amp
Duty Cycle: None
DMX: 2 DMX Channel Modes: 9 Channel
Mode & 11 Channel Mode
Colors: 7 + White
Gobos: 7 + Spot
Sound Active: Ye s
Working Position: Any Safe, Secure Position
Warranty: 2 Year (730 days)
Please Note: Specications and improvements in the design
of this unit and this manual are subject to change without any
prior written notice.
No warranty, whether expressed or implied, is given or made with respect to any accessory supplied with
products described above. Except to the extent prohibited by applicable law, all implied warranties made
by ADJ Products, LLC in connection with this product, including warranties of merchantability or fitness,
are limited in duration to the warranty period set forth above. And no warranties, whether expressed or
implied, including warranties of merchantability or fitness, shall apply to this product after said period
has expired. The consumer’s and/or Dealer’s sole remedy shall be such repair or replacement as is
expressly provided above; and under no circumstances shall ADJ Products, LLC be liable for any loss or
damage, direct or consequential, arising out of the use of, or inability to use, this product.
This warranty is the only written warranty applicable to ADJ Products, LLC Products and
supersedes all prior warranties and written descriptions of warranty terms and conditions heretofore
published.
MANUFACTURER’S LIMITED WARRANTY PERIODS:
•LightingProducts=1-year(365days)LimitedWarranty(Such as: Special Effect Lighting, Intelligent
Lighting, UV lighting, Strobes, Fog Machines, Bubble Machines, Mirror Balls, Par Cans, Trussing,
Lighting Stands etc. excluding LEDs and lamps)
•LaserProducts=90-DayLimitedWarranty
•L.E.D.Products=2-year(730days)LimitedWarranty(excluding motors, PCB boards, and power
supplies, which have a 1-year (365 day Limited Warranty) and batteries which have a 180 day
limited warranty).
ADJ Products, LLC - www.adj.com - Inno Pocket Spot Pearl Instruction Manual Page 26
Auto Sensing Voltage: This xture contains a automatic volt-
age switch, which will auto sense the voltage when it is plugged
into the power source.
ADJ Products, LLC
6122 S. Eastern Ave. Los Angeles, CA 90040 USA
Tel: 323-582-2650 / Fax: 323-725-6100
Web: www.adj.com / E-mail: info@americandj.com
A.D.J. Supply Europe B.V.
Junostraat 2
6468 EW Kerkrade
Netherlands
service@adjgroup.eu / www.adj.eu
Tel: +31 45 546 85 00 / Fax: +31 45 546 85 99
146.3mm/5.75”
119.9mm/4.72”
214mm/8.42”
264.5mm/10.41”
71mm/2.8”
147mm/5.78”
159mm/6.25”
Loading...