Page 1
INNO BEAM LED
©2013 ADJ Products, LLC all rights reserved. Information,
specications, diagrams, images, and instructions herein are
subject to change without notice. ADJ Products, LLC logo and
identifying product names and numbers herein are trademarks
of ADJ Products, LLC. Copyright protection claimed includes all
forms and matters of copyrightable materials and information
now allowed by statutory or judicial law or hereinafter granted.
Product names used in this document may be trademarks or
registered trademarks of their respective companies and are
hereby acknowledged. All non-ADJ Products, LLC brands and
product names are trademarks or registered trademarks of their
respective companies.
ADJ Products, LLC and all aliated companies hereby disclaim any and all liabilities for property, equipment, building,
and electrical damages, injuries to any persons, and direct or
indirect economic loss associated with the use or reliance of
any information contained within this document, and/or as a
result of the improper, unsafe, unsucient and negligent assembly, installation, rigging, and operation of this product.
3/15
User Instructions
Europe Energy Saving Notice
Energy Saving Matters (EuP 2009/125/EC)
Saving electric energy is a key to help protecting the enviroment.
Please turn o all electrical products when they are not in use. To
avoid power consumption in idle mode, disconnect all electrical
equipment from power when not in use. Thank you!
Page 2
Inno Beam LED General Information
Inno Beam LED General Instructions
Unpacking: Thank you for purchasing the Inno Beam LED by ADJ
Products, LLC. Every Inno Beam LED has been thoroughly tested and
has been shipped in perfect operating condition. Carefully check the
shipping carton for damage that may have occurred during shipping.
If the carton appears to be damaged, carefully inspect your xture for
any damage and be sure all equipment necessary to operate the unit
has arrived intact. In the event damage has been found or parts are
missing, please contact our toll free customer support number for further instructions. Please do not return this unit to your dealer without
contacting customer support rst.
Introduction: The Inno Beam LED is a 13 channel DMX intelligent,
moving head, LED fixture. The Inno Beam LED can operate as a stand
alone fixture or in a Master/Slave configuration. The Inno Beam LED
has three operating modes; a sound active, show mode, DMX con-
trolled. This fixture is suitable for theaters, studios, retail stores, and
other similar locations. For best results use fog or special effects smoke
to enhance the beams projections.
Customer Support: ADJ Products, LLC provides a toll free cus-
tomer support line, to provide help and to answer any question should
you encounter problems during your set up or initial operation. You
may also visit us on the web at www.adj.com for any comments or
suggestions. Service Hours are Monday through Friday 8:00 a.m. to
4:30 p.m. Pacic Standard Time.
Voice: (800) 322-6337
Fax: (323) 582-2941
E-mail: support@americandj.com
Warning! To prevent or reduce the risk of electrical shock or re, do
not expose this unit to rain or moisture.
Warning! This may cause severe eye damage. Avoid looking directly
into the light source at all times!
To optimize the performance of this product, please read these
operating instructions carefully to familiarize yourself with the basic
operations of this unit. These instructions contain important safety
information regarding the use and maintenance of this unit. Please
keep this manual with the unit, for future reference.
Inno Beam LED Features
• DMX-512 Protocol Compatible
• 2 DMX Modes: 12 Channel Mode & 14 Channel Mode
• 8 Colors + White
• 4 Fixed Gobos & 4 Spots
• 3 Operating Modes - Sound Active, Show Mode, & DMX Control
• Digital Display for Address and Function Setting
• UC3 Control (Controller Not Included)
• 4 Preprogrammed Shows
• Power Cord Daisy Chain (See page 10)
Inno Beam LED Warranty Registration
The Inno Beam LED carries a 2 year (730 days) limited warranty.
Please fill out the enclosed warranty card to validate your purchase
and warranty. You may also register your product online at www. adjproducts.com. All returned service items whether under warranty or
not, must be freight pre-paid and accompany a return authorization
(R.A.) number. If the unit is under warranty you must provide a copy
of your proof of purchase invoice. Please contact ADJ Products, LLC
customer support for a R.A. number.
Inno Beam LED Handling Precautions
Caution! There are no user serviceable parts inside this unit. Do not
attempt any repairs yourself, doing so will void your manufactures
warranty. In the unlikely event your unit may require service please
contact ADJ Products, LLC.
During operation the housing may become extremely hot. Avoid
touching the unit with bare hands while in use.
ADJ Products, LLC will not accept any liability for any resulting damages caused by the non-observance of this manual or any unauthor-
ized modication to this unit.
ADJ Products, LLC - www.adj.com - Inno Beam LED Instruction Manual Page 3ADJ Products, LLC - www.adj.com - Inno Beam LED Instruction Manual Page 2
Page 3
Inno Beam LED Safety Precautions
Inno Beam LED Mounting
For Your Own Personal Safety, Please Read and Understand This
Manual Completely Before You Attempt To Install Or Operate
This Unit!
• To reduce the risk of electrical shock or re, do not expose this unit
rain or moisture
• Do not spill water or other liquids into or on to your unit.
• Be sure that the local power outlet match that of the required volt age for your unit.
• Do not attempt to operate this unit if the power cord has been
frayed or broken.
• Do not attempt to remove or break o the ground prong from
the electrical cord. This prong is used to reduce the risk of electrical
shock and re in case of an internal short.
• Disconnect from main power before making any type of connection.
• Do not remove the cover under any conditions. There are no user
serviceable parts inside.
• Never operate this unit when it’s cover is removed.
• Always be sure to mount this unit in an area that will allow proper
ventilation. Allow about 6” (15cm) between this device and a wall.
• Do not attempt to operate this unit, if it becomes damaged.
• This unit is intended for indoor use only, use of this product out doors voids all warranties.
• Always mount this unit in safe and stable matter.
• Power-supply cords should be routed so that they are not likely to
be walked on or pinched by items placed upon or against them,
paying particular attention to cords at plugs, convenience recep tacles, and the point where they exit from the appliance.
• Cleaning -The fixture should be cleaned only as recommended by
the manufacturer. See page 28 for cleaning details.
• Heat -This fixture should be situated away from heat sources such
as radiators, heat registers, stoves, or other appliances (including
amplifiers) that produce heat.
• The fixture should be serviced by qualified service personnel when:
A. Objects have fallen, or liquid has been spilled into the appliance.
B. The appliance has been exposed to rain or water.
C. The appliance does not appear to operate normally or exhibits
a marked change in performance.
When installing the unit, the trussing or area of installation must be
able to hold 10 times the weight without any deformation. When
installing the unit must be secured with a secondary safety attachment, e.g. and appropriate safety cable. Never stand directly below
the unit when mounting, removing, or servicing the unit.
Overhead mounting requires extensive experience, including calculating working load limits, installation material being used, and perodic
safety inspection of all installation material and unit. If you lack these
qualications, do not attempt the installation yourself.
The installaiton should be checked by a skilled person once a year.
The Inno Beam LED is fully operational in two dierent mounting
positions, hanging upside-down from a ceiling or set on a at level
surface. To avoid internal damage to the unit, never mount the unit on
its side as illustrated above. Be sure this xture is kept at least 0.5m
away from any ammable materials (decoration etc.). Always use
and install the supplied safety cable as a safety measure to prevent
accidental damage and/or injury in the event the clamp fails (see next
page).
ADJ Products, LLC - www.adj.com - Inno Beam LED Instruction Manual Page 6ADJ Products, LLC - www.adj.com - Inno Beam LED Instruction Manual Page 5
Page 4
Inno Beam LED Mounting
Inno Beam LED Set Up
NOTICE: The suitable enviromental temperature for this light-
ing xture is between -25˚ C to 45˚ C. Do not place this lighting
xture in an enviroment where the temperatures are under or
above the temperatures stated above. This will allow the xture
to run at its best and help prolong the xture life.
Power Supply: The ADJ Inno Beam LED contains a automatic volt-
age switch, which will auto sense the voltage when it is plugged into
a power source. With this switch there is no need to worry about the
correct power voltage, this unit can be plugged in anywhere.
DMX-512: DMX is short for Digital Multiplex. This is a universal pro-
tocol used by most lighting and controller manufactures as a form of
communication between intelligent fixtures and controllers. A DMX
controller sends DMX data instructions from the controller to the fixture. DMX data is sent as serial data that travels from fixture to fixture
via the DATA “IN” and DATA “OUT” XLR terminals located on all DMX
fixtures (most controllers only have a DATA “OUT” terminal).
DMX Linking: DMX is a language allowing all makes and models
of dierent manufactures to be linked together and operate from a
single controller, as long as all xtures and the controller are DMX
compliant. To ensure proper DMX data transmission, when using
several DMX fixtures try to use the shortest cable path possible. The
order in which fixtures are connected in a DMX line does not influence
the DMX addressing. For example; a fixture assigned a DMX address
of 1 may be placed anywhere in a DMX line, at the beginning, at the
end, or anywhere in the middle. Therefore, the first fixture controlled
by the controller could be the last fixture in the chain. When a fixture
is assigned a DMX address of 1, the DMX controller knows to send
DATA assigned to address 1 to that unit, no matter where it is located
in the DMX chain.
Data Cable (DMX Cable) Requirements (For DMX and Master/Slave
Operation): The Inno Beam LED can be controlled via DMX-512 pro-
tocol. The Inno Beam LED has 2 DMX modes. The DMX address is
Screw one clamp via a M12 screw and nut onto the Omega
holder. Insert the quick-lock fasteners of the Omega holder
into the respective holes on the bottom of the Inno Beam LED.
Tighten the quick-lock fasteners fully clockwise. Pull the safetycable through the hole on the bottom of the base and over the
trussing system or a safe xation spot. Insert the end in the
carabine and tighten the safety screw.
ADJ Products, LLC - www.adj.com - Inno Beam LED Instruction Manual Page 7 ADJ Products, LLC - www.adj.com - Inno Beam LED Instruction Manual Page 8
set electronically using the controls on the front
panel of the unit. Your unit and your DMX controller require a approved DMX-512 110 Ohm Data
cable for data input and data output (Figure 1). We
recommend Accu-Cable DMX cables. If you are
making your own cables, be sure to use standard
110-120 Ohm shielded cable (This cable may be
purchased at almost all professional sound and
lighting stores). Your cables should be made with
Figure 1
Page 5
Inno Beam LED Set Up
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
DMX512
DMX+,DMX-,COMMON
1
2
3
Termination reduces signal errors and
avoids signal transmission problems
and interference. It is always advisable
to connect a DMX terminal, (Resistance
120 Ohm 1/4 W) between PIN 2 (DMX-)
and PIN 3 (DMX +) of the last fixture.
POWER
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
Inno Beam LED Set Up
a male and female XLR connector on either end of the cable. Also
remember that DMX cable must be daisy chained and cannot be split.
Notice: Be sure to follow gures two and three when making your own
cables. Do not use the ground lug on the XLR connector. Do not connect the cable’s shield conductor to the ground lug or allow the shield
conductor to come in contact with the XLR’s outer casing. Grounding
the shield could cause a short circuit and erratic behavior.
COMMON
1
DMX512 IN
3
3-PIN XLR
2
Figure 2
XLR Pin Conguration
Pin 1 = Ground
Pin 2 = Data Compliment (negative)
Pin 3 = Data True (positive)
XLR Male Socket
1 Ground
Figure 3
DMX512 OUT
3-PIN XLR
2 Cold
3 Hot
1
3
2
XLR Female Socket
2 Cold
DMX +
DMX -
1 Ground
3 Hot
5-Pin XLR DMX Connectors.
Some manufactures use 5-pin DMX-
512 data cables for DATA transmission in place of 3-pin. 5-pin DMX
xtures may be implemented in a 3-pin DMX line. When inserting standard 5-pin data cables in to a 3-pin line a cable adaptor must be used,
these adaptors are readily available at most electric stores. The chart
below details a proper cable conversion.
3-Pin XLR to 5-Pin XLR Conversion
Conductor 5-Pin XLR Male (In)3-Pin XLR Female (Out)
Ground/Shield
Data Compliment (- signal)
Data True (+ signal)
Not Used
Not Used
Pin 1
Pin 2
Pin 3
Pin 1
Pin 2
Pin 3
Pin 4 - Do Not Use
Pin 5 - Do Not Use
Inno Beam LED Power Cord Daisy Chain
Special Note: Line Termination.
used, you may need to use a terminator on the last unit to avoid erratic
When longer runs of cable are
behavior. A terminator is a 110-120 ohm 1/4 watt resistor which is connected between pins 2 and 3 of a male XLR connector (DATA + and
DATA -). This unit is inserted in the female XLR connector of the last
unit in your daisy chain to terminate the line. Using a cable terminator
(ADJ part number Z-DMX/T) will decrease the possibilities of erratic
behavior.
Termination reduces signal errors and
1
avoids signal transmission problems
3
and interference. It is always advisable
2
to connect a DMX terminal, (Resistance
120 Ohm 1/4 W) between PIN 2 (DMX-)
and PIN 3 (DMX +) of the last fixture.
Figure 4
With this feature you can connect the xtures to one another
using the IEC input and output sockets. The quantity that can be
connected is 3 xtures maximum for 120V, and 6 xtures maximum for 240V. After the maximum xtures has been reached you
will need to use a new power outlet. They must be the same xtures. DO NOT mix xtures.
ADJ Products, LLC - www.adj.com - Inno Beam LED Instruction Manual Page 10ADJ Products, LLC - www.adj.com - Inno Beam LED Instruction Manual Page 9
Page 6
Inno Beam LED System Menu
MENU
Fixture Time
Firmwa re Ve rs io n
DMX Address
Channel Mode
Show Mode
Dimmer Mode
Inno Beam LED System Menu
System Menu: When making adjustments you can press
ENTER to conrm your setup then press and hold the
MENU button for at least 3 seconds to lock it in, or you can
wait 8 seconds for automatic setup. To exit without making
any adjustments press the MENU button.
CONTROL PANEL LOCK:
The control panel will lock itself after 30 seconds if nothing is pressed. To unlock the control panel, press the MENU
button for 3 seconds.
DMX Address - Set the DMX Address -
Slave Mo de
No DMX
Sound S tate
Sound S ense
Pan Inve rt
Tilt Inve rt
Back L ight
Di mm er C al ib ra t
Auto Test
Reset
ADJ Products, LLC - www.adj.com - Inno Beam LED Instruction Manual Page 11
1. Press the MENU button until “DMX Addresss” is displayed,
press ENTER.
2. “X” will now be displayed, “X” represents the displayed
address. Press the UP or DOWN buttons to nd your desired
address.
3. Press ENTER to conrm, and then press and hold the MENU
button for at least three seconds to assign.
Channel Mode - This will let you select your desired
DMX Channel mode.
1. Press the MENU button until “Channel Mode” is displayed,
press ENTER.
2. “X Chan” will now be displayed, “X” represents the displayed
DMX channel mode; either 12 Channel Mode or 14 Channel
Mode. Press the UP or DOWN buttons to nd your desired Chan-
nel mode.
3. Press ENTER to conrm.
Show Mode - Show modes 1 - 4 (Factory Shows).
1. Press the MENU button until “Show Mode” is displayed, press
ENTER.
ADJ Products, LLC - www.adj.com - Inno Beam LED Instruction Manual Page 12
Page 7
Inno Beam LED System Menu
Inno Beam LED System Menu
2. “Show X” will now be displayed, “X” representing a number
between 1-4. Press the UP or DOWN buttons to nd your desired
show and press ENTER to conrm.
3. Press and hold the MENU button for at least 3 seconds to
activate.
Dimmer Mode - In this mode you can select the dimmer
curve. See page 26 for the different dimmer modes.
1. Press the MENU button until “Dimmer Mode” is displayed,
press ENTER.
2. The current dimmer mode will be displayed.
3. Press the UP or DOWN buttons to nd your desired dimmer
mode and press ENTER to conrm.
Slave Mode - This will let you set unit as a master or
slave in a master/slave conguration.
1. Press the MENU button until “Slave Mode” is displayed,
press ENTER. Either “Slave 1” or “Slave 2” will be displayed.
2. Press the UP or DOWN buttons until your desired slave
mode is displayed, press ENTER to conm.
NOTE: In a Master/Slave conguration you can make one
xture the Master and then set the next xture to “Slave 2”, the
xtures will now have contrast movement to each other.
either “Show”, “Blackout”, or “Hold” will be displayed beneath.
2. Press ENTER and the bottom choice will begin to ash. Use
the UP or DOWN buttons to choose an operating mode you
would like the unit to start up in when power is applied or the
DMX signal is lost.
• Show - If the DMX signal is lost, or interrupted, the unit will
automatically go into the last selected show mode.
• Blackout- If the DMX signal is lost or interrupted, the unit will
automatically go into stand by mode.
• Hold - If the DMX signal is lost, or interrupted, the xture will
stay in the last DMX setting. If power is applied and this mode is
set, the unit will automatically go into the last DMX set up.
3. Press ENTER to conrm your desired set up.
Sound State - In this mode the unit will run in sound
active mode.
1. Press the MENU button until “Sound State” is displayed, press
ENTER.
2. Either “On” or “O” will now be displayed. Use the UP or
DOWN buttons to toggle between “On” and “O”.
3. Press ENTER to conrm your selection, the press and hold the
MENU button to activate.
No DMX - This mode can be used as a precaution mode,
that in case the DMX signal is lost, interrupted, or power is
lost, the operating mode chosen in the setup is the running
mode the xture will go into when the DMX signal is lost. You
can also set this as the operating mode you would like the
unit to return to when power is applied.
1. Press the MENU button until “NO DMX” is displayed, and
ADJ Products, LLC - www.adj.com - Inno Beam LED Instruction Manual Page 13 ADJ Products, LLC - www.adj.com - Inno Beam LED Instruction Manual Page 14
Sound Sense - In this mode you can adjust the sound
sensitivity of the sound active mode.
1. Press the MENU button until “Sound Sense” is displayed,
press ENTER.
2. Press the UP or DOWN buttons to adjust the sensitivity level.
The sensitivity level can be adjusted between 0 (the lowest) and
100 (most sensitive).
Page 8
Inno Beam LED System Menu Inno Beam LED System Menu
3. Press ENTER to set you desired level.
Pan Invert - Pan Inversion
1. Press the MENU button until “Pan Invert” is displayed, press
ENTER. Either “Yes” or “No” will be displayed.
2. To activate the Pan inversion press the UP or DOWN buttons
until “Yes” is displayed, press ENTER to conm. To deactivate
Pan inversion, select “No” and press Enter.
Tilt Invert - Tilt Inversion
1. Press the MENU button until “Tilt Invert” is displayed, press
ENTER. Either “Yes” or “No” will be displayed.
2. To activate the Tilt inversion press the UP or DOWN buttons
until “Yes” is displayed, press ENTER to conm. To deactivate
Tilt inversion, select “No” and press Enter.
Back Light - With this function you can make the back-
light automatically turn off after one minute.
1. Press the MENU button until “Back Light” is displayed, press
ENTER.
2. Either “ON” or “OFF” will now be displayed. Press the UP or
DOWN buttons to select “ON” to keep the backlight on at all
times, or “OFF” to allow the backlight to turn o after 2 minutes.
Press any button to turn the backlight on again.
3. Press ENTER to conrm.
resents the instensity setting. Use the UP or DOWN buttons to
adjust the LED output intensity. 50 being medium intensity, and
100 being full intensity.
3. When you have found your desired setting press ENTER to
conrm.
Auto Test - This function will run a self test program.
1. Press the MENU button until “Auto Test” is displayed, press
ENTER.
2. The xture will now run a self test. Press the MENU button to
exit.
Fixture Temp. - With this function you can display the
running temperature of the unit.
1. Press the MENU button until “Fixture Temp.” is displayed,
press ENTER.
2. The current running temperature of the xture will now be
displayed. Press MENU to exit.
Fixture Time - With this function you can display the
running time of the unit.
1. Press the MENU button until “Fixture Time” is displayed,
press ENTER.
2. The running time of the xture will now be displayed. Press
MENU to exit.
Dimmer Calibrat - With this function you can set the
output intensity.
1. Press the MENU button until “Dimmer Calibrat” is displayed,
press ENTER.
2. A number between 50-100 will be displayed. This number rep-
Firmware Version - This will display the software ver-
sion
1. Press the MENU button until “Firmware Version” is displayed.
Press the ENTER button and the software vesion will be dis-
played.
ADJ Products, LLC - www.adj.com - Inno Beam LED Instruction Manual Page 16ADJ Products, LLC - www.adj.com - Inno Beam LED Instruction Manual Page 15
Page 9
Inno Beam LED System Menu
2. Press the MENU button to leave this function.
Reset - Use this function to reset the motors.
1. Tap the MENU button until “Reset” is displayed, press
ENTER.
2. The xture will now reset the motors.
Inno Beam LED Home Adjustment Menu
To enter the home adjustment submenu, press the ENTER button for
at least 5 seconds. In this submenu you are able to adjust the original
position (home position) of certain functions.
Pan Oset - Adjustment of the pan home position.
1. Press the ENTER button for at least 3 seconds, then press the UP
or DOWN buttons so that “Pan Offset” is displayed, press ENTER.
2. Use the UP and DOWN buttons to make your adjustments, and
then press ENTER to conrm. Press the MENU button for one second
to exit.
Tilt Oset - Adjustment of the tilt home position.
1. Press the ENTER button for at least 3 seconds, then press the UP
or DOWN buttons so that “Tilt Offset” is displayed, press ENTER.
2. Use the UP and DOWN buttons to make your adjustments, and
then press ENTER to conrm. Press the MENU button for one second
to exit.
Color Oset - Home setting adjustment for the color
wheel.
1. Press the ENTER button for at least 3 seconds, then press the UP
or DOWN buttons so that “Color Offset” is displayed, press ENTER.
2. Use the UP and DOWN buttons to make your adjustments, and
ADJ Products, LLC - www.adj.com - Inno Beam LED Instruction Manual Page 17 ADJ Products, LLC - www.adj.com - Inno Beam LED Instruction Manual Page 18
Page 10
Inno Beam LED Home Adjustment Menu
Inno Beam LED Operation
then press ENTER to conrm. Press the MENU button for one second
to exit.
Gobo Oset - Home setting adjustment for the gobo
wheel.
1. Press the ENTER button for at least 3 seconds, then press the UP
or DOWN buttons so that “Gobo Offset” is displayed, press ENTER.
2. Use the UP and DOWN buttons to make your adjustments, and
then press ENTER to conrm. Press the MENU button for one second
to exit.
Prism Oset - Home setting adjustment for the prism.
1. Press the ENTER button for at least 3 seconds, then press the UP
or DOWN buttons so that “Prism Offset” is displayed, press ENTER.
2. Use the UP and DOWN buttons to make your adjustments, and
then press ENTER to conrm. Press the MENU button for one second
to exit.
RPrism Oset - Home setting adjustment for the rotat-
ing prism.
1. Press the ENTER button for at least 3 seconds, then press the
UP or DOWN buttons so that “RPrism Offset” is displayed, press
ENTER.
2. Use the UP and DOWN buttons to make your adjustments, and
then press ENTER to conrm. Press the MENU button for one second
to exit.
Frost Oset - Home setting adjustment for the frost.
1. Press the ENTER button for at least 3 seconds, then press the UP
or DOWN buttons so that “Frost Offset” is displayed, press ENTER.
2. Use the UP and DOWN buttons to make your adjustments, and
then press ENTER to conrm. Press the MENU button for one second
to exit.
ADJ Products, LLC - www.adj.com - Inno Beam LED Instruction Manual Page 19 ADJ Products, LLC - www.adj.com - Inno Beam LED Instruction Manual Page 20
Operating Modes:
• Sound Active mode -
The fixture will react to sound, chasing through the built-in programs.
• Show mode -
The fixture will run one of four shows that you choose.
• DMX control mode -
This function will allow you to control each individual fixtures traits
with a standard DMX-512 controller such as the Elation® Show
Designer.
™
Universal DMX Control: This function allows you to use a Elation®
universal DMX-512 controller to control the chases and patterns,
dimmer and strobe. A DMX controller allows you to create unique
programs tailored to your individual needs.
1. The Inno Beam LED has 2 DMX modes; a 12 channel mode and
14 channel mode. See pages 22-27 for detailed description of the
DMX values and traits.
2. To control your fixture in DMX mode, follow the set-up procedures
on pages 8-10 as well as the set-up specifications that are includ ed with your DMX controller.
3. Use the controller’s faders to control the various DMX fixture traits.
4. This will allow you to create your own programs.
5. Follow the instructions on page 12 to set the DMX address.
6. For longer cable runs (more than a 100 feet) use a terminator on
the last fixture.
7. For help operating in DMX mode consult the manual included
with your DMX controller.
Sound Active Mode: This mode allows either single unit or several
units linked together, to run to the beat of the music.
1. Press the MENU button until “Sound State” is displayed, and
press ENTER. Press the UP or DOWN buttons so that “ON”
is displayed and press ENTER.
2. The sound sensitivity can be adjusted by pressing the MENU
button until “Sound Sense” is displayed. Press ENTER and use
the UP and DOWN buttons to adjust the sound sensitivity. “0”
being the least sensitive and “100” being the most.
3. The optional UC3 Controller (not included) may be used to con-
trol different functions including blackout.
Page 11
Inno Beam LED Operation
Show Mode: This mode allows either a single unit or several units
linked together, to run one of four shows that you choose.
1. Press the MENU button until “Show Mode” is displayed, and
press ENTER.
2. Press the UP or DOWN buttons until you nd your desired show,
and press ENTER.
Inno Beam LED Master-Slave Setup
Master-Slave Conguration This function will allow you to link up
to 16 units together and operate without a controller. The units will
be sound activated. In Master-Slave operation one unit will act as the
controlling unit and the others will react to the controlling units programs. Any unit can act as a Master or as a Slave.
1. Using approved DMX data cables, daisy chain your units togeth-
er via the XLR connector on the rear of the units. Remember the
Male XLR connector is the input and the Female XLR connector
is the output. The rst unit in the chain (master) will use the female
XLR connector only - The last unit in the chain will use the male
XLR connector only. For longer cable runs we suggest a termina tor at the last fixture.
2. On the Master unit find your desired show and set that show by
pressing the ENTER button.
3. On the slave units tap the MENU button until “Slave Mode” is
displayed, and Press ENTER. Choose either “Slave 1” or “Slave
2” and press ENTER. See pages 13-14 for more info.
4. The slave units will now follow the Master unit.
Inno Beam LED UC3 Control
The optional UC3 Controller (not included) may be used to con-
trol different functions including blackout.
Stand By
Function
Mode
Blackout the unit
1. Sync. Strobe
2. Async strobe
3. Sound Strobe
Sound (LED OFF)
Show
1-4
Show (LED
Slow Blinking)
1. Press to select color
2. Hold to select gobo
LED ON
Inno Beam LED 12 Channel Mode
Channel Value Function
1 0 - 255 PAN
2 0 - 255 TILT
3 COLORS
0 - 7 OPEN
8 - 14 RED
15 - 21 ORANGE
22 - 28 YELLOW
29 - 35 GREEN
36 - 42 BLUE
43 - 49 MAGENTA
50 - 56 LIGHT BLUE
57 - 63 PINK
64 - 127 SPLIT COLORS
128 - 189 RAINBOW EFFECT FAST - SLOW
190 - 193 STOP
194 - 255 RAINBOW EFFECT SLOW - FAST
4 GOBO WHEEL
0 - 7 OPEN
8 - 15 GOBO 1
16 - 23 GOBO 2
24 - 31 GOBO 3
32 - 39 GOBO 4
40 - 47 GOBO 5
48 - 55 GOBO 6
56 - 63 GOBO 7
64 - 71 OPEN SHAKE
72 - 79 GOBO 1 SHAKE
80 - 87 GOBO 2 SHAKE
88 - 95 GOBO 3 SHAKE
96 - 103 GOBO 4 SHAKE
104 - 111 GOBO 5 SHAKE
112 - 119 GOBO 6 SHAKE
120 - 127 GOBO 7 SHAKE
128 - 189 GOBO WHEEL ROTATION FAST - SLOW
190 - 193 STOP
194 - 255 GOBO WHEEL ROTATION SLOW - FAST
ADJ Products, LLC - www.adj.com - Inno Beam LED Instruction Manual Page 21 ADJ Products, LLC - www.adj.com - Inno Beam LED Instruction Manual Page 22
Page 12
Inno Beam LED 12 Channel Mode
Inno Beam LED 12 Channel Mode
Channel Value Function
5 PRISM EFFECT
0 - 7 NO EFFECT
8 - 255 PRISM EFFECT
6 PRISM ROTATION
0 - 127 360° PRISM INDEXING
128 - 189 COUNTER-CLOCKWISE ROTATION
FAST - SLOW
190 - 193 STOP
194 - 255 CLOCKWISE ROTATION SLOW - FAST
7 SHUTTER
0 - 7 OFF
8 - 15 OPEN
16 - 131 STROBING SLOW - FAST
Channel Value Function
11 BLACKOUT/RESET
200 - 209 RESET ALL
210 - 255 NOTHING
12 DIMMER MODES
0 - 20 STANDARD
21 - 40 STAGE
41 - 60 TV
61 - 80 ARCHITECTURAL
81 - 100 THEATRE
101 - 255 UNIT DEFAULT
To disable blackouts under channel 11, set the fader to the
according blackout values and wait 3 seconds
132 - 139 OPEN
140 - 181 SLOW OPEN - FAST CLOSE
182 - 189 OPEN
190 - 231 FAST OPEN - SLOW CLOSE
232 - 239 OPEN
240 - 247 RANDOM STROBE
248 - 255 OPEN
8 0 - 255 MASTER DIMMER 0% - 100%
9 0 - 255 FROST
10 0 -255 PAN/TILT SPEED FAST - SLOW
11 BLACKOUT/RESET
0 - 69 NOTHING
70 - 79 ENABLE BLACKOUT W/ PAN/TILT
MOVEMENT
80 - 89 DISABLE BLACKOUT W/ PAN/TILT
MOVEMENT
90 - 99 ENABLE BLACKOUT W/ COLOR
CHANGE
100 - 109 DISABLE BLACKOUT W/ COLOR
CHANGE
110 - 119 ENABLE BLACKOUT W/ GOBO
CHANGE
120 - 199 DISABLE BLACKOUT W/ GOBO
CHANGE
ADJ Products, LLC - www.adj.com - Inno Beam LED Instruction Manual Page 23 ADJ Products, LLC - www.adj.com - Inno Beam LED Instruction Manual Page 24
Page 13
Inno Beam LED 14 Channel Mode
Inno Beam LED 14 Channel Mode
Channel Value Function
1 0 - 255 PAN
2 0 - 255 PAN FINE
3 0 - 255 TILT
4 0 - 255 TILT FINE
5 COLORS
0 - 7 OPEN
8 - 14 RED
15 - 21 ORANGE
22 - 28 YELLOW
29 - 35 GREEN
36 - 42 BLUE
43 - 49 MAGENTA
50 - 56 LIGHT BLUE
57 - 63 PINK
64 - 127 SPLIT COLORS
128 - 189 RAINBOW EFFECT FAST - SLOW
190 - 193 STOP
194 - 255 RAINBOW EFFECT SLOW - FAST
6 GOBO WHEEL
0 - 7 OPEN
8 - 15 GOBO 1
16 - 23 GOBO 2
24 - 31 GOBO 3
32 - 39 GOBO 4
40 - 47 GOBO 5
48 - 55 GOBO 6
56 - 63 GOBO 7
64 - 71 OPEN SHAKE
72 - 79 GOBO 1 SHAKE
80 - 87 GOBO 2 SHAKE
88 - 95 GOBO 3 SHAKE
96 - 103 GOBO 4 SHAKE
104 - 111 GOBO 5 SHAKE
112 - 119 GOBO 6 SHAKE
120 - 127 GOBO 7 SHAKE
128 - 189 GOBO WHEEL ROTATION FAST - SLOW
Channel Value Function
6 GOBO WHEEL CONT.
190 - 193 STOP
194 - 255 GOBO WHEEL ROTATION SLOW - FAST
7 PRISM EFFECT
0 - 7 NO EFFECT
8 - 255 PRISM EFFECT
8 PRISM ROTATION
0 - 127 360° PRISM INDEXING
128 - 189 COUNTER-CLOCKWISE ROTATION
FAST - SLOW
190 - 193 STOP
194 - 255 CLOCKWISE ROTATION SLOW - FAST
9 SHUTTER
0 - 7 OFF
8 - 15 OPEN
16 - 131 STROBING SLOW - FAST
132 - 139 OPEN
140 - 181 SLOW OPEN - FAST CLOSE
182 - 189 OPEN
190 - 231 FAST OPEN - SLOW CLOSE
232 - 239 OPEN
240 - 247 RANDOM STROBE
248 - 255 OPEN
10 0 - 255 MASTER DIMMER 0% - 100%
11 0 - 255 FROST
12 0 -255 PAN/TILT SPEED FAST - SLOW
13 BLACKOUT/RESET
0 - 69 NOTHING
70 - 79 ENABLE BLACKOUT W/ PAN/TILT
MOVEMENT
80 - 89 DISABLE BLACKOUT W/ PAN/TILT
MOVEMENT
90 - 99 ENABLE BLACKOUT W/ COLOR
CHANGE
100 - 109 DISABLE BLACKOUT W/ COLOR
CHANGE
ADJ Products, LLC - www.adj.com - Inno Beam LED Instruction Manual Page 26ADJ Products, LLC - www.adj.com - Inno Beam LED Instruction Manual Page 25
Page 14
R
G
B
1458 417
154
115
82
2790
780 356 207 143
425
123 58 36
28
RGBW
1m 2m 3m 4m 5m
4500
1280 584 339 227
1.0 2.0 3.0 4.0
Distance(m)
0
0m( )
5.0
60
Distance(m)
0m( )
30900 10920 4916 2085
1788
17
1213
INNO BEAM LED
Inno Beam LED Photometric Chart Inno Beam LED 14 Channel Mode
Channel Value Function
13 BLACKOUT/RESET
110 - 119 ENABLE BLACKOUT W/ GOBO
CHANGE
120 - 199 DISABLE BLACKOUT W/ GOBO
CHANGE
200 - 209 RESET ALL
210 - 255 NOTHING
14 DIMMER MODES
0 - 20 STANDARD
21 - 40 STAGE
41 - 60 TV
61 - 80 ARCHITECTURAL
81 - 100 THEATRE
101 - 255 UNIT DEFAULT
To disable blackouts under channel 13, set the fader to the
according blackout values and wait 3 seconds
Distance(m)
159000 75300 40060 19930
0
1.0 2.0 3.0 4.0
14470
6
5.0
Inno Beam LED Dimmer Curve Chart
Ramp Effect
(Fade Time) (Fade Time)
9800
0m( )
6.0
Standard
Stage
TV
Architectural
Theatre
ADJ Products, LLC - www.adj.com - Inno Beam LED Instruction Manual Page 27 ADJ Products, LLC - www.adj.com - Inno Beam LED Instruction Manual Page 28
Page 15
Inno Beam LED Fuse Replacement
Locate and remove the unit’s power cord. Once the cord has been
removed located the fuse holder located inside the power socket.
Insert a flat-head screw driver into the power socket and gently pry
out the fuse holder. Remove the bad fuse and replace with a new one.
The fuse holder has a built-in socket for a spare fuse be sure not to
confuse the spare fuse with active fuse.
Inno Beam LED Cleaning
Due to fog residue, smoke, and dust cleaning the internal and external optical lenses and mirror should be carried out periodically to
optimize light output. Cleaning frequency depends on the environment in which the fixture operates (I.e. smoke, fog residue, dust,
dew). In heavy club use we recommend cleaning on a monthly basis.
Periodic cleaning will ensure longevity, and crisp output.
1. Use normal glass cleaner and a soft cloth to wipe down the out-
side casing.
2. Use a brush to wipe down the cooling vents and fan grill.
3. Clean the external optics with glass cleaner and a soft cloth every
20 days.
4. Clean the internal optics with glass cleaner and a soft cloth every
30-60 days.
5. Always be sure to dry all parts completely before plugging the unit
back in.
Inno Beam LED Trouble Shooting
Trouble Shooting: Listed below are a few common problems that
you may encounter, with solutions.
No light output from the unit;
1. Be sure you have connected your unit into a standard 120v wall
outlet. Be sure to voltage selector switch in the correct position.
2. Be sure the external fuse has not blown. The fuse is located on
the rear panel of the unit.
3. Be sure the fuse holder is completely and properly seated.
Unit does not respond to sound;
1. Low frequencies (bass) should cause the unit to react to sound.
Tapping on the microphone, quiet or high pitched sounds may
not activate the unit.
Inno Beam LED Warranty
MANUFACTURER’S LIMITED WARRANTY
A. ADJ Products, LLC hereby warrants, to the original purchaser, ADJ Products, LLC products
to be free of manufacturing defects in material and workmanship for a prescribed period from
the date of purchase (see specific warranty period on reverse). This warranty shall be valid only if the
product is purchased within the United States of America, including possessions and
territories. It is the owner’s responsibility to establish the date and place of purchase by acceptable
evidence, at the time service is sought.
B. For warranty service you must obtain a Return Authorization number (RA#) before sending back
the product–please contact ADJ Products, LLC Service Department at 800-322-6337. Send the pro duct only to the ADJ Products, LLC factory. All shipping charges must be pre-paid. If the requested
repairs or service (including parts replacement) are within the terms of this warranty, ADJ Products, LLC
will pay return shipping charges only to a designated point within the United States. If the entire instru ment is sent, it must be shipped in it’s original package. No accessories should be shipped with the product.
If any accessories are shipped with the product, ADJ Products, LLC shall have no liability whatsoever for
loss of or damage to any such accessories, nor for the safe return thereof.
C. This warranty is void if the serial number has been altered or removed; if the product is modified in any
manner which ADJ Products, LLC concludes, after inspection, affects the reliability of the product; if the
product has been repaired or serviced by anyone other than the ADJ Products, LLC factory unless prior
written authorization was issued to purchaser by ADJ Products, LLC; if the product is damaged because
not properly maintained as set forth in the instruction manual.
D. This is not a service contract, and this warranty does not include maintnance, cleaning or periodic check
up. During the period specified above, ADJ Products, LLC will replace defective parts at its expense
with new or refurbished parts, and will absorb all expenses for warranty service and repair labor by
reason of defects in material or workmanship. The sole responsibility of ADJ Products, LLC under this
warranty shall be limited to the repair of the product, or replacement thereof, including parts, at the sole
discretion of ADJ Products, LLC. All products covered by this warranty were manufactured after August
15, 2012, and bear indentifying marks to that effect.
E. ADJ Products, LLC reserves the right to make changes in design and/or improvements upon its products
without any obligation to include these changes in any products theretofore manufactured.
No warranty, whether expressed or implied, is given or made with respect to any accessory supplied with
products described above. Except to the extent prohibited by applicable law, all implied warranties made
by ADJ Products, LLC in connection with this product, including warranties of merchantability or fitness,
are limited in duration to the warranty period set forth above. And no warranties, whether expressed or
implied, including warranties of merchantability or fitness, shall apply to this product after said period
has expired. The consumer’s and/or Dealer’s sole remedy shall be such repair or replacement as is
expressly provided above; and under no circumstances shall ADJ Products, LLC be liable for any loss or
damage, direct or consequential, arising out of the use of, or inability to use, this product.
This warranty is the only written warranty applicable to ADJ Products, LLC Products and
supersedes all prior warranties and written descriptions of warranty terms and conditions heretofore
published.
MANUFACTURER’S LIMITED WARRANTY PERIODS:
•LightingProducts=1-year(365days)LimitedWarranty(Such as: Special Effect Lighting, Intelligent
Lighting, UV lighting, Strobes, Fog Machines, Bubble Machines, Mirror Balls, Par Cans, Trussing,
Lighting Stands etc. excluding LEDs and lamps)
•LaserProducts=90-DayLimitedWarranty
•L.E.D.Products=2-year(730days)LimitedWarranty(excluding motors, PCB boards, and power
supplies, which have a 1-year (365 day Limited Warranty) and batteries which have a 180 day
limited warranty).
ADJ Products, LLC - www.adj.com - Inno Beam LED Instruction Manual Page 30ADJ Products, LLC - www.adj.com - Inno Beam LED Instruction Manual Page 29
Page 16
Inno Beam LED Specifications
Model: Inno Beam LED
Voltage: 100 - 240V 50/60Hz
LED: 1 x 80W LED
Power Consumption: 129W
Power Cord Daisy Chain: 3 Fixtures Max. (120V)
6 Fixtures Max. (240V)
Dimensions: 11.5”(L) x 7.5”(W) x 18.25”(H)
289mm x 188mm x 461mm
Beam Angle: 6 Degrees
Weight: 18 Lbs. / 8.2 kgs.
Fuse: 7 Amp
Duty Cycle: None
DMX: 12 DMX Channels & 14 DMX Channels
Colors: 8 + White
Gobos: 4 + 4 Spots
Sound Active: Ye s
Working Position: Any Safe, Secure Position
Warranty: 2 Year (730 days)
Auto Sensing Voltage: This xture contains a automatic volt-
age switch, which will auto sense the voltage when it is plugged
into the power source.
Please Note: Specications and improvements in the design
of this unit and this manual are subject to change without any
prior written notice.
ADJ Products, LLC - www.adj.com - Inno Beam LED Instruction Manual Page 31
ADJ Products, LLC
6122 S. Eastern Ave. Los Angeles, CA 90040 USA
Tel: 323-582-2650 / Fax: 323-725-6100
Web: www.adj.com / E-mail: info@americandj.com
A.D.J. Supply Europe B.V.
Junostraat 2
6468 EW Kerkrade
Netherlands
service@adjgroup.eu / www.adj.eu
Tel: +31 45 546 85 00 / Fax: +31 45 546 85 99
Loading...