specications, diagrams, images, and instructions herein are
subject to change without notice. ADJ Products, LLC logo and
identifying product names and numbers herein are trademarks
of ADJ Products, LLC. Copyright protection claimed includes all
forms and matters of copyrightable materials and information
now allowed by statutory or judicial law or hereinafter granted.
Product names used in this document may be trademarks or
registered trademarks of their respective companies and are
hereby acknowledged. All non-ADJ Products, LLC brands and
product names are trademarks or registered trademarks of their
respective companies.
ADJ Products, LLC and all aliated companies hereby disclaim any and all liabilities for property, equipment, building,
and electrical damages, injuries to any persons, and direct or
indirect economic loss associated with the use or reliance of
any information contained within this document, and/or as a
result of the improper, unsafe, unsucient and negligent assembly, installation, rigging, and operation of this product.
1/16
User Instructions
Europe Energy Saving Notice
Energy Saving Matters (EuP 2009/125/EC)
Saving electric energy is a key to help protecting the enviroment.
Please turn o all electrical products when they are not in use. To
avoid power consumption in idle mode, disconnect all electrical
equipment from power when not in use. Thank you!
Ikon Profile Introduction
Ikon Profile Warranty Registration
To optimize the performance of this product, please read these operating
instructions carefully to familiarize yourself with the basic operations of
this unit. These instructions contain important safety information regarding the use and maintenance of this unit. Please keep this manual with the
unit, for future reference.
Unpacking:
Thank you for purchasing the Ikon Profile by ADJ Products, LLC. Every
Ikon Prole has been thoroughly tested and has been shipped in perfect
operating condition. Carefully check the shipping carton for damage that
may have occurred during shipping. If the carton appears to be damaged,
carefully inspect your unit for any damage and be sure all equipment nec-
essary to operate the system has arrived intact. In the event damage has
been found or parts are missing, please contact our toll free customer
support number for further instructions. Please do not return the unit to
your dealer without rst contacting customer support.
Customer Support:
ADJ Products, LLC provides a toll free customer support line, to provide
set up help and to answer any question should you encounter problems
during your set up or initial operation. You may also visit us on the web at
www.adj.com for any comments or suggestions. For service related issue
please contact ADJ Products, LLC. Service Hours are Monday through
Friday 8:00 a.m. to 4:30 p.m. Pacic Standard Time.
Voice: (800) 322-6337
Fax: (323) 582-2941
E-mail: support@americandj.com
Warning! To prevent or reduce the risk of electrical shock or re, do not
expose this unit to rain or moisture.
Caution! This may cause eye damage. Avoid looking directly into the light
source. Use sensible precaution.
Caution! There are no user serviceable parts inside this unit. Do not
attempt any repairs yourself, doing so will void your manufactures warranty. In the unlikely event your unit may require service please contact
ADJ Products, LLC.
PLEASE do not discard the shipping carton in the trash. Please recycle when ever possible.
The Ikon Profile carries a two year (730 days) limited warranty. Please
fill out the enclosed warranty card to validate your purchase. All
returned service items whether under warranty or not, must be freight
pre-paid and accompany a return authorization (R.A.) number. If the
unit is under warranty you must provide a copy of your proof of purchase invoice. Please contact ADJ customer support for a R.A. number.
Ikon Profile Precautions
Safety Issue: This unit may blow the fuse if the maximum allotted
load of 2 amps is reached. If the fuse needs replacement, please see
fuse replacement on page 14.
• Be sure the local power outlet match the required voltage of the
unit.
• Disconnect from main power before making any type of connection.
• Do not remove the cover under any conditions. There are no user
serviceable parts inside.
• Always be sure to mount this unit in an area that will allow proper
ventilation. Allow about 6” (15cm) between this device and a wall.
• To reduce the risk of electrical shock or re, do not expose this unit
rain or moisture
• This unit is intended for indoor use only, use of this product out doors voids all warranties.
• During long periods of non-use, disconnect the unit’s main power.
• Always mount this unit in safe and stable matter.
• Power-Cord Protection - Power-supply cords should be routed
so that they are not likely to be walked on or pinched by items
placed upon or against them, paying particular attention to cords at
plugs, convenience receptacles, and the point where they exit from
the fixture. Do not attempt to remove or break o the ground prong
from the electrical cord. This prong is used to reduce the risk of
electrical shock and re in case of an internal short.
• The fixture should be serviced by qualified service personnel when:
A. The power cord or the plug has been damaged.
B. Objects have fallen, or liquid has been spilled into the appliance.
C. The appliance has been exposed to rain or water.
D. The fixture does not appear to operate normally or exhibits a
marked change in performance.
navigate system menu. This next section will detail the functions of
each command in the system menu. Please read the next section
thoroughly!
To access the main menu press the MENU button. Press the UP or
DOWN buttons until you reach function you wish to change. When
you reach the function you wish to change press the ENTER button.
When a function is selected use the UP or DOWN buttons to change
the function settings. Once your changes are made press the ENTER
button, and then press and hold the MENU button for at least three
seconds to conrm and lock the change into the system memory. If
the MENU button is not pressed and held within eight seconds the
xture will automatically conrm and lock the change into the system
memory. To exit without making any changes press the MENU button.
The Ikon Prole comes with an easy to
ADDR -DMX Address Setting.
1. Press the MENU button until “ADDR” is displayed, press
ENTER.
2. The current DMX address will now be displayed and ashing.
Press the UP or DOWN buttons to nd your desired address.
Press ENTER to set your desired DMX address.
NOTE: If after you connect your DMX controller the unit does
not fall into DMX mode, press and hold the MENU button for at
least 3 seconds.
DNST - This mode can be used as a precaution mode,
that in case the DMX signal is lost, interrupted, or power is
lost, the operating mode chosen in the setup is the running
mode the xture will go into when the DMX signal is lost. You
can also set this as the operating mode you would like the
unit to return to when power is applied.
1. Press the MENU button until “DNST” is displayed, and either
“MASL”, “BLND”, or “LAST” will be displayed beneath.
2. Press ENTER and the bottom choice will begin to ash. Use
the UP or DOWN buttons to choose an operating mode you
would like the unit to start up in when power is applied or the
DMX signal is lost.
• MASL (Master Slave) - If the DMX signal is lost or power is
applied, the unit will automatically go into Master Slave mode
and run a built-in show.
• BLND (Blackout) - If the DMX signal is lost or interrupted, the
unit will automatically go into stand by mode.
• LAST - If the DMX signal is lost the xture will stay in the last
DMX setting. If power is applied and this mode is set, the unit will
automatically go into the last DMX set up.
3. Press ENTER to conrm your desired set up.
SLND - This will let you set unit as a master or slave in
a master/slave conguration.
1. Press the MENU button until “SLND” is displayed, press
ENTER. “MAST” or “SL 1” will be displayed.
2. Press the UP or DOWN buttons until your desired setting is
displayed, press ENTER to conm and exit.
DIND - This will let select your desired dimmer curve.
1. Press the MENU button until “DIND” is displayed, and press
ENTER. 1 of 5 dimmer curves will be displayed. “STDA” (standard), “STGE” (stage), “TV” (TV), “ARAL” (Architectural), or
“THAL” (Theatre). See the dimmer curve chart on page 28 for
more info.
2. Press the UP or DOWN buttons to nd your desired dimmer
curve and press ENTER to conm and exit.
LED - With this function the LED display will turn off
after 2 minutes.
1. Press the MENU button until “LED” is displayed, press
ENTER.
2. The display will show either “ON” or “OFF”. Press the UP or
DOWN buttons to select “ON” to keep the LED display on at
all times, or “OFF” to allow the LED display to turn o after 2
minutes. Press any button to turn on the LED display again.
3. Press ENTER to conrm and exit.
DISP - This function will reverse the display 180º.
1. Press the MENU button until “DISP” is displayed, press
ENTER.
2. Press the UP button to select “DISP” to activate this function, or “DSIP” to deactivate this function.
3. Press ENTER to conrm.
MANU - In this submenu you are able to test the dimmer,
and strobe.
TEST - This function will run a self test program.
1. Press the MENU button until “TEST” is displayed, press
ENTER.
2. The xture will now run a self test.
TEMP - With this function you can check the tempera-
ture of the xture.
1. Press the MENU button until “TEMP” is displayed, press
ENTER.
2. The xture temperature will now be displayed. Press MENU
to exit.
FHRS - With this function you can display the running
time of the unit.
1. Press the MENU button until “FHRS” is displayed, press
ENTER.
2. The display shows the running time of the unit. Press MENU
to exit.
1. Press the MENU button until “MANU” is displayed, press
ENTER.
2. Use the UP and DOWN buttons to scroll through the various
functions able for testing. Once you have found your desired
function you would like to test press ENTER.
3. After you have pressed ENTER, use the UP and DOWN buttons to adjust the values and test the function. To exit press the
MENU button.
0 - 7 CLOSED
8 - 15 OPEN
16 - 131 STROBE SLOW - FAST
132 - 139 OPEN
140 - 181 FAST CLOSE - SLOW OPEN
182 - 189 OPEN
190 - 231 SLOW CLOSE - FAST OPEN
232 - 239 OPEN
240 - 247 RANDOM STROBE
248 - 255 OPEN
2 0 - 255 MASTER DIMMER 0% - 100%
3 DIMMER MODE
0 - 20 STANDARD
21 - 40 STAGE
41 - 60 TV
61 - 80 ARCHITECTURAL
81 - 100 THEATRE
101 - 255 DEFAULT DIMMER SETTING
Ikon Profile CAD Drawing
The Ikon Profile gobo can be interchanged at any time and allows
you to customize your system.
To replace gobo;
1. Gently slide the gobo housing out of the top of unit. The gobo
housing is located in front of the top flag.
2. Once the gobo housing has been removed, remove the retaining
ring that holds the gobo in. This can easily be done using needle
nose pliers.
3. Remove and replace the gobo with your desired replacement.
Reinsert the retainer ring, and make sure the ring rests firmly
against the gobo.
4. Slide the gobo assembly back into place.
Ikon Profile Adding a Color Gel
A color gel (not included) can be added to the front of the Ikon Profile
and can be interchanged at any time. This allows you to customize
your system.
To add a color gel;
1. Locate the color gel frame at the front of the unit. Slide the spring
lever back and slide the gel frame out of the holder.
2. Once the gel frame has been removed slide your desired color gel
into the middle of the frame.
3. Slide the spring back and slide the gel frame into place.
The unit should be mounted using a mounting clamp (not provided),
axing it to the mounting bracket that is provided with the unit.
Always ensure that the unit is rmly xed to avoid vibration and slipping while operating. Always ensure that the structure to which you
are attaching the unit is secure and is able to support a weight of 10
times the unit’s weight. Also, always use a safety cable that can hold
12 times the weight of the unit when installing the xture. The equipment must be installed by a professional, and it must be installed in a
place where it is out of the reach of people’s grasp.
Ikon Profile Photometric Chart
(LUX)
(LUX)
Distanc e(m)
15
30
0
352 00
950 0
1.0
893 0 379 0 21 20 128 0
236 0 98 5 583 374
15 30 ~
2.03.04.0
0m( )
5.0
Ikon Profile Gobos
The UC IR (sold separately) infrared remote gives you control of
various functions (See below). To control the fixture you must aim the
remote at the front of the fixture and be no more than 30 feet away.
The Ikon Profile comes with the Airstream IR remote transmitter.
The transmitter plugs into the headphone jack of your iOS phone
or tablet. To control your IR fixture you must raise the volume to the
maximum on your iOS phone or table and aim the transmitter at the
front of the fixture and be no more than 15 feet away. After you have
purchased the Airstream IR transmitters, the app is a free download
from the app store for your iOS phone or tablet. The app comes with
3 pages of control depending on the IR fixture you are using. Please
see below for IR functions including the corresponding app page.
Works with App page 1.
STAN D BY - Pressing this button will blackout the fixture.
FULL ON - This button is invalid for this fixture.
STROBE - Press and hold this button to activate strobing.
FADE/GOBO - This button is invalid for this fixture.
“DIMMER +” and “DIMMER -” - Use these buttons to adjust the out-
put intensity.
1-9 - These buttons are invalid for this fixture.
SOUND ON & OFF - These button’s are invalid for this fixture.
With this feature you can connect the xtures to one another
using the IEC input and output sockets. The quantity that can
be connected is 16 xtures maximum @ 120V and 27 xtures
maximum @ 230V. After the maximum xture’s is reached you will
need to use a new power outlet. They must be the same xtures.
DO NOT mix xtures.
Ikon Profile Trouble Shooting
No light output from the unit;
1. Be sure the fuse has not popped. The fuse is located on the rear panel.
2. Be sure the 4 flags are open and not closed.
Ikon Profile Fuse Replacement
First unplug the power. The fuse holder is located next to the I.E.C
power cord output. Using a phillips-head screw driver unscrew the
fuse holder. Remove the bad fuse and replace with a new one.
Ikon Profile Cleaning
Fixture Cleaning:
Due to fog residue, smoke, and dust cleaning the internal and external optical lenses should be carried out periodically to optimize light
output. Cleaning frequency depends on the environment in which the
fixture operates (I.e. smoke, fog residue, dust, dew). In heavy club
use we recommend cleaning on a monthly basis. Periodic cleaning
will ensure longevity, and crisp output.
1. Use normal glass cleaner and a soft cloth to wipe down the out-
side casing.
2. Clean the external optics with glass cleaner and a soft cloth every
20 days.
3. Clean the internal optics with glass cleaner and a soft cloth every
30-60 days.
4. Always be sure to dry all parts completely before plugging the unit
back in.
A. ADJ Products, LLC hereby warrants, to the original purchaser, ADJ Products, LLC products
to be free of manufacturing defects in material and workmanship for a prescribed period from
the date of purchase (see specific warranty period on reverse). This warranty shall be valid only if the
product is purchased within the United States of America, including possessions and
territories. It is the owner’s responsibility to establish the date and place of purchase by acceptable
evidence, at the time service is sought.
B. For warranty service you must obtain a Return Authorization number (RA#)
before sending back the product–please contact ADJ Products, LLC Service Department
at 800-322-6337. Send the product only to the ADJ Products, LLC factory. All
shipping charges must be pre-paid. If the requested repairs or service (including
parts replacement) are within the terms of this warranty, ADJ Products, LLC will pay return
shipping charges only to a designated point within the United States. If the entire instrument is
sent, it must be shipped in it’s original package. No accessories should be shipped with the product. If
any accessories are shipped with the product, ADJ Products, LLC shall have no liability whatsoever for
loss of or damage to any such accessories, nor for the safe return thereof.
C. This warranty is void if the serial number has been altered or removed; if the product is modified in any
manner which ADJ Products, LLC concludes, after inspection, affects the reliability of the product; if the
product has been repaired or serviced by anyone other than the ADJ Products, LLC factory unless prior
written authorization was issued to purchaser by ADJ Products, LLC; if the product is damaged because
not properly maintained as set forth in the instruction manual.
D. This is not a service contract, and this warranty does not include maintnance, cleaning or periodic check
up. During the period specified above, ADJ Products, LLC will replace defective parts at its expense
with new or refurbished parts, and will absorb all expenses for warranty service and repair labor by
reason of defects in material or workmanship. The sole responsibility of ADJ Products, LLC under this
warranty shall be limited to the repair of the product, or replacement thereof, including parts, at the sole
discretion of ADJ Products, LLC. All products covered by this warranty were manufactured after August
15, 2012, and bear indentifying marks to that effect.
E. ADJ Products, LLC reserves the right to make changes in design and/or improvements upon its products
without any obligation to include these changes in any products theretofore manufactured.
No warranty, whether expressed or implied, is given or made with respect to any accessory supplied with
products described above. Except to the extent prohibited by applicable law, all implied warranties made
by ADJ Products, LLC in connection with this product, including warranties of merchantability or fitness,
are limited in duration to the warranty period set forth above. And no warranties, whether expressed or
implied, including warranties of merchantability or fitness, shall apply to this product after said period
has expired. The consumer’s and/or Dealer’s sole remedy shall be such repair or replacement as is
expressly provided above; and under no circumstances shall ADJ Products, LLC be liable for any loss or
damage, direct or consequential, arising out of the use of, or inability to use, this product.
This warranty is the only written warranty applicable to ADJ Products, LLC Products and
supersedes all prior warranties and written descriptions of warranty terms and conditions heretofore
published.
MANUFACTURER’S LIMITED WARRANTY PERIODS:
•LightingProducts=1-year(365days)LimitedWarranty(Such as: Special Effect Lighting, Intelligent
Lighting, UV lighting, Strobes, Fog Machines, Bubble Machines, Mirror Balls, Par Cans, Trussing,
Lighting Stands etc. excluding LED and lamps)
•LaserProducts=1Year(365Days)LimitedWarranty(excluding laser diodes which have a 6 month
limited warranty)
•L.E.D.Products=2-year(730days)LimitedWarranty(excluding motors, PCB boards, and power
supplies, which have a 1-year (365 day Limited Warranty) batteries which have a 180 day limited war-
ranty). Only the L.E.D.s carry a 2-year warranty (excludingStarTecSerieswhichacarriesa1Year
LimitedWarranty)
•ADJDMXControllers=2Year(730Days)LimitedWarranty(excluding faders and tact switches)