ADJ Ikon Profile Ikon Profile_EN Rev 01-16.pdf

User Instructions

1/16 A.D.J. Supply Europe B.V.

Junostraat 2

6468 EW Kerkrade

The Netherlands

www.adj.eu

A.D.J. Supply Europe B.V. – www.adj.eu – Ikon Profile User Instructions Page 2

©2016 ADJ Products, LLC all rights reserved. Information, specifications, diagrams, images, and instructions
herein are subject to change without notice. ADJ Products, LLC logo and identifying product names and
numbers herein are trademarks of ADJ Products, LLC. Copyright protection claimed includes all forms and
matters of copyrightable materials and information now allowed by statutory or judicial law or hereinafter
granted. Product names used in this document may be trademarks or registered trademarks of their respective
companies and are hereby acknowledged. All non-ADJ Products, LLC brands and product names are
trademarks or registered trademarks of their respective companies.

ADJ Products, LLC and all affiliated companies hereby disclaim any and all liabilities for property, equipment,
building, and electrical damages, injuries to any persons, and direct or indirect economic loss associated with
the use or reliance of any information contained within this document, and/or as a result of the improper,
unsafe, unsufficient and negligent assembly, installation, rigging, and operation of this product.

A.D.J. Supply Europe B.V. – www.adj.eu – Ikon Profile User Instructions Page 3

Contents

INTRODUCTION ....................................................................................................................................................................... 4

PRECAUTIONS ......................................................................................................................................................................... 4

FIXTURE LAYOUT ..................................................................................................................................................................... 5

SYSTEM MENU ........................................................................................................................................................................ 6

DMX VALUES & TRAITS ........................................................................................................................................................... 8

CAD DRAWING ........................................................................................................................................................................ 8

GOBO REPLACEMENT ............................................................................................................................................................. 9

ADDING A COLOR GEL ............................................................................................................................................................. 9

INSTALLATION ......................................................................................................................................................................... 9

PHOTOMETRIC CHART .......................................................................................................................................................... 10

GOBOS .................................................................................................................................................................................. 10

ADJ UC IR CONTROL .............................................................................................................................................................. 10

POWER CORD DAISY CHAIN .................................................................................................................................................. 10

TROUBLE SHOOTING ............................................................................................................................................................. 11

FUSE REPLACEMENT ............................................................................................................................................................. 11

CLEANING.............................................................................................................................................................................. 11

SPECIFICATIONS .................................................................................................................................................................... 12

ROHS - A great Contribution to the Conservation of Environment ..................................................................................... 13

WEEE – Waste of Electrical and Electronic Equipment ........................................................................................................ 14

NOTES ................................................................................................................................................................................... 15

A.D.J. Supply Europe B.V. – www.adj.eu – Ikon Profile User Instructions Page 4

INOZIONE
INTRODUCTION

To optimize the performance of this product, please read these operating instructions carefully to familiarize
yourself with the basic operations of this unit. These instructions contain important safety information regarding
the use and maintenance of this unit. Please keep this manual with the unit, for future reference.
Unpacking: Thank you for purchasing the Ikon Profile by ADJ Products, LLC. Every Ikon Profile has been
thoroughly tested and has been shipped in perfect operating condition. Carefully check the shipping carton for
damage that may have occurred during shipping. If the carton appears to be damaged, carefully inspect your
fixture for any damage and be sure all equipment necessary to operate the unit has arrived intact. In the event
damage has been found or parts are missing, please contact our toll free customer support number for further
instructions. Please do not return this unit to your dealer without contacting customer support first.
Customer Support: If you encounter any problems, please contact your trusted American Audio shop.
We also offer the possibility, to contact us directly: You can contact us via our website www.adj.eu or via
email: [e-mail]
Warning! To prevent or reduce the risk of electrical shock or fire, do not expose this unit to rain or moisture.

Caution! This may cause eye damage. Avoid looking directly into the light source. Use sensible precaution.
Caution! There are no user serviceable parts inside this unit. Do not attempt any repairs yourself, doing so will

void your manufactures warranty. In the unlikely event your unit may require service please contact ADJ
Products, LLC.

PLEASE do not discard the shipping carton in the trash. Please recycle when ever possible.

PRECAUTIONS

Safety Issue: This unit may blow the fuse if the maximum allotted load of 2 amps is reached. If the fuse needs
replacement, please see fuse replacement on page 11.

• Be sure the local power outlet match the required voltage of the unit.

• Disconnect from main power before making any type of connection.

• Do not remove the cover under any conditions. There are no user serviceable parts inside.

• Always be sure to mount this unit in an area that will allow proper ventilation. Allow about 6” (15cm) between

this device and a wall.

• To reduce the risk of electrical shock or fire, do not expose this unit rain or moisture

• This unit is intended for indoor use only, use of this product outdoors voids all warranties.

• During long periods of non-use, disconnect the unit’s main power.

• Always mount this unit in safe and stable matter.

• Power-Cord Protection - Power-supply cords should be routed so that they are not likely to be walked on or

pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience
receptacles, and the point where they exit from the fixture. Do not attempt to remove or break off the ground
prong from the electrical cord. This prong is used to reduce the risk of electrical shock and fire in case of an
internal short.

• The fixture should be serviced by qualified service personnel when:
A. The power cord or the plug has been damaged.
B. Objects have fallen, or liquid has been spilled into the appliance.
C. The appliance has been exposed to rain or water.
D. The fixture does not appear to operate normally or exhibits a marked change in performance.

A.D.J. Supply Europe B.V. – www.adj.eu – Ikon Profile User Instructions Page 5

FIXTURE LAYOUT

1. LED

DMX

On

DMX input present

MASTER

On

Master Mode

SLAVE

ON

Slave Mode

2. Button:

MENU

To select the programming functions

▲ UP

To go forward in the selected functions

▼ DOWN

To go backward in the selected functions

ENTER

To confirm the selected functions

3. Fuse (T 2A): Protect the unit from damage of over current

4. Display: To show the various menus and the selected function

5. Power In/Out: Power cable input/output connections

6. DMX In/Out: 3-pin XLR connections for DMX 512 operation

7. Flags: Use thes e to a dju st the fram ing of your gobo

8. Knobs: Move to adjust the beam angle from 15 to 4 0 degree and to focus the gobo

9. Spring: To lock the color gel frame into place

A.D.J. Supply Europe B.V. – www.adj.eu – Ikon Profile User Instructions Page 6

SYSTEM MENU

On-Board System Menu. The Ikon Profile comes with an easy to navigate system menu. This next section
will detail the functions of each command in the system menu. Please read the next section thoroughly!

To access the main menu press the MENU button. Press the UP or DOWN buttons until you reach function
you wish to change. When you reach the function you wish to change press the enter button. When a function
is selected use the UP or Down buttons to change the function settings. Once your changes are made press
the enter button, and then press and hold the MENU button for at least three seconds to confirm and lock the
change into the system memory. If the menu button is not pressed and held within eight seconds the fixture
will automatically confirm and lock the change into the system memory. To exit without making any changes
press the MENU button.

DMX Address

Slave Mode

DMX Last State

Dimmer Mode

BackLight

Display

Manual Test

Auto Test

Fixture Tempreture
Fixture Hours

Software version

A.D.J. Supply Europe B.V. – www.adj.eu – Ikon Profile User Instructions Page 7

SYSTEM MENU (continued)

ADDR - DMX Address Setting.

1. Press the MENU button until “ADDR” is displayed, press ENTER.

2. The current DMX address will now be displayed and flashing.
Press the UP or DOWN buttons to find your desired address.
Press ENTER to set your desired DMX address.
NOTE: If after you connect your DMX controller the unit does not fall into DMX mode, press and hold the
MENU button for at least 3 seconds.

SLND - This will let you set unit as a master or slave in a master/slave configuration.

1. Press the MENU button until “SLND” is displayed, press ENTER. “MAST” or “SL 1” will be displayed.

2. Press the UP or DOWN buttons until your desired setting is displayed, press ENTER to confirm and exit.

DNST - This mode can be used as a precaution mode, that in case the DMX signal is lost, interrupted,

or power is lost, the operating mode chosen in the setup is the running mode the fixture will go into
when the DMX signal is lost. You can also set this as the operating mode you would like the unit to
return to when power is applied.

1. Press the MENU button until “DNST” is displayed, and either “MASL”, “BLND”, or “LAST” will be displayed
beneath.

2. Press ENTER and the bottom choice will begin to flash. Use the UP or DOWN buttons to choose an
operating mode you would like the unit to start up in when power is applied or the DMX signal is lost.

• MASL (Master Slave) - If the DMX signal is lost or power is applied, the unit will automatically go into Master
Slave mode and run a built-in show.

• BLND (Blackout) - If the DMX signal is lost or interrupted, the unit will automatically go into stand by mode.

• LAST - If the DMX signal is lost the fixture will stay in the last DMX setting. If power is applied and this mode

is set, the unit will automatically go into the last DMX set up.

3. Press ENTER to confirm your desired set up.

DIND - This will let select your desired dimmer curve.

1. Press the MENU button until “DIND” is displayed, and press ENTER. 1 of 5 dimmer curves will be displayed.
“STDA” (standard), “STGE” (stage), “TV” (TV), “ARAL” (Architectural), or “THAL” (Theatre). 2. Press the UP or

DOWN buttons to find your desired dimmer curve and press ENTER to confim and exit.

LED - With this function the LED display will turn off after 2 minutes.

1. Press the MENU button until “LED” is displayed, press ENTER.

2. The display will show either “ON” or “OFF”. Press the UP or DOWN buttons to select “ON” to keep the LED

display on at all times, or “OFF” to allow the LED display to turn off after 2 minutes. Press any button to turn on
the LED display again.

3. Press ENTER to confirm and exit.

DISP - This function will reverse the display 180º.

1. Press the MENU button until “DISP” is displayed, press ENTER.

2. Press the UP button to select “DISP” to activate this function, or “DSIP” to deactivate this function.

3. Press ENTER to confirm.

MANU - In this submenu you are able to test the dimmer, and strobe.

1. Press the MENU button until “MANU” is displayed, press ENTER.

2. Use the UP and DOWN buttons to scroll through the various functions able for testing. Once you have found
your desired function you would like to test press ENTER.

3. After you have pressed ENTER, use the UP and DOWN buttons to adjust the values and test the function.
To exit press the MENU button.

TEST - This function will run a self test program.

1. Press the MENU button until “TEST” is displayed, press ENTER.

2. The fixture will now run a self test.

A.D.J. Supply Europe B.V. – www.adj.eu – Ikon Profile User Instructions Page 8

SYSTEM MENU (continued)

TEMP - With this function you can check the temperature of the fixture.

1. Press the MENU button until “TEMP” is displayed, press ENTER.

2. The fixture temperature will now be displayed. Press MENU to exit.

FHRS - With this function you can display the running time of the unit.

1. Press the MENU button until “FHRS” is displayed, press ENTER.

2. The display shows the running time of the unit. Press MENU to exit.

VER - Use this function to display the Software version of the unit.

1. Press the MENU button until “VER” is displayed, press ENTER.

2. The display will show the software version.

DMX VALUES & TRAITS

Channel

Value

Function

1

STROBING/SHUTTER

0 - 7

CLOSED

8 - 15

OPEN

16 - 131

STROBE SLOW - FAST

132 - 139

OPEN

140 - 181

FAST CLOSE - SLOW OPEN

182 - 189

OPEN

190 - 231

SLOW CLOSE - FAST OPEN

232 - 239

OPEN

240 - 247

RANDOM STROBE

248 - 255

OPEN

2

0 - 255

MASTER DIMMER 0% - 100%

3

DIMMER MODE

0 - 20

STANDARD

21 - 40

STAGE

41 - 60

TV

61 - 80

ARCHITECTURAL

81 - 100

THEATRE

101 - 255

DEFAULT DIMMER SETTING

CAD DRAWING

A.D.J. Supply Europe B.V. – www.adj.eu – Ikon Profile User Instructions Page 9

GOBO REPLACEMENT

The Ikon Profile gobo can be interchanged at any time and allows you to customize your system.
To replace gobo;

1. Gently slide the gobo housing out of the top of unit. The gobo housing is located in front of the top flag.

2. Once the gobo housing has been removed, remove the retaining ring that holds the gobo in. This can easily
be done using needle nose pliers.

3. Remove and replace the gobo with your desired replacement. Reinsert the retainer ring, and make sure the
ring rests firmly against the gobo.

4. Slide the gobo assembly back into place.

ADDING A COLOR GEL

A color gel (not included) can be added to the front of the Ikon Profile and can be interchanged at any time.
This allows you to customize your system.
To add a color gel;

1. Locate the color gel frame at the front of the unit. Slide the spring lever back and slide the gel frame out of
the holder.

2. Once the gel frame has been removed slide your desired color gel into the middle of the frame.

3. Slide the spring back and slide the gel frame into place.

INSTALLATION

The unit should be mounted using a mounting clamp (not provided), affixing it to the mounting bracket that is
provided with the unit. Always ensure that the unit is firmly fixed to avoid vibration and slipping while operating.
Always ensure that the structure to which you are attaching the unit is secure and is able to support a weight

of 10 times the unit’s weight. Also, always use a safety cable that can hold 12 times the weight of the unit

when installing the fixture. The equipment must be installed by a professional, and it must be installed in a
place where it is out of the reach of people’s grasp.

Allation

Color Gel Splint

Spring

A.D.J. Supply Europe B.V. – www.adj.eu – Ikon Profile User Instructions Page 10

n Profile

PHOTOMETRIC CHART

GOBOS

ADJ UC IR CONTROL

The UC IR (sold separately) infrared remote gives you control of various functions (See below). To control
the fixture you must aim the remote at the front of the fixture and be no more than 30 feet away.
The Ikon Profile comes with the Airstream IR remote transmitter. The transmitter plugs into the headphone
jack of your iOS phone or tablet. To control your IR fixture you must raise the volume to the maximum on your
iOS phone or table and aim the transmitter at the front of the fixture and be no more than 15 feet away. After
you have purchased the Airstream IR transmitters, the app is a free download from the app store for your iOS
phone or tablet. The app comes with 3 pages of control depending on the IR fixture you are using. Please see
below for IR functions including the corresponding app page.

Works with App page 1.
STAND BY - Pressing this button will blackout the fixture.
FULL ON - This button is invalid for this fixture.
STROBE - Press and hold this button to activate strobing.
FADE/GOBO - This button is invalid for this fixture.
“DIMMER +” and “DIMMER -” - Use these buttons to adjust the output intensity.
1-9 - These buttons are invalid for this fixture.
SOUND ON & OFF - These button’s are invalid for this fixture.
SHOW - This button is invalid for this fixture.

POWER CORD DAISY CHAIN

With this feature you can connect the fixtures to one another using the IEC input and output sockets.
The quantity that can be connected is 16 fixtures maximum @ 120V and 27 fixtures maximum @ 230V.
After the maximum fixture’s is reached you will need to use a new power outlet. They must be the
same fixtures. DO NOT mix fixtures.

Distance(m)

A.D.J. Supply Europe B.V. – www.adj.eu – Ikon Profile User Instructions Page 11

TROUBLE SHOOTING

No light output from the unit;

1. Be sure the fuse has not popped. The fuse is located on the rear panel.

2. Be sure the 4 flags are open and not closed.

FUSE REPLACEMENT

First unplug the power. The fuse holder is located next to the I.E.C power cord output. Using a phillips-head
screw driver unscrew the fuse holder. Remove the bad fuse and replace with a new one.

CLEANING

Fixture Cleaning:

Due to fog residue, smoke, and dust cleaning the internal and external optical lenses should be carried out
periodically to optimize light output. Cleaning frequency depends on the environment in which the fixture
operates (I.e. smoke, fog residue, dust, dew). In heavy club use we recommend cleaning on a monthly basis.
Periodic cleaning will ensure longevity, and crisp output.

1. Use normal glass cleaner and a soft cloth to wipe down the outside casing.

2. Clean the external optics with glass cleaner and a soft cloth every 20 days.

3. Clean the internal optics with glass cleaner and a soft cloth every 30-60 days.

4. Always be sure to dry all parts completely before plugging the unit back in.

A.D.J. Supply Europe B.V. – www.adj.eu – Ikon Profile User Instructions Page 12

SPECIFICATIONS

Model:

Ikon Profile

Voltage:
LED:
Power Consumption:
PowerCon Daisy Chain:

Colours:
Beam Angle:
Dimensions:

Weight:
Gobos:

Fuse:
Duty Cycle:

100-240V, 50/60Hz
1 x 32W White LED
44W
16 Fixtures Max. (120V)
27 Fixtures Max. (230V)
White
15 - 30 Degrees
16”(L) x 6”(W) x 5”(H)
403 x 150 x 127mm
6 Lbs./ 2.7 Kgs
Size: 26.8mm
Viewable: 24mm
2 Amp
None

Auto Sensing Voltage: This fixture contains an automatic voltage switch, which will auto sense the voltage

when it is plugged into the power source.

Please Note: Specifications and improvements in the design of this unit and this manual are subject to change
without any prior written notice.

A.D.J. Supply Europe B.V. – www.adj.eu – Ikon Profile User Instructions Page 13

ROHS - A great Contribution to the Conservation of Environment

Dear Customer,
The European Union has adopted a directive on the restriction / prohibition of the use of hazardous

substances. This directive, referred to as ROHS, is a frequently discussed topic in the electronic industry.
It restricts, among other things, six materials: Lead (Pb), Mercury (Hg), hexavalent chromium (CR VI),

cadmium (Cd), polybrimated biphenyls as flame retardant (PBB), polybrominated diphenyl, also a flame
retardant (PBDE). The directive applies to nearly all electronic and electrical devices whose mode of operation
involves electric or electromagnetic fields – in short: each kind of electronics we have around us in our
households or at work.

As manufacturers of products of the brands of AMERICAN AUDIO, AMERICAN DJ, ELATION Professional
and ACCLAIM Lighting, we are obligated to comply with the RoHS directive. Therefore, as early as two years
prior to the directive coming into force, we started our search for alternative environmentally friendly materials
and manufacturing processes.

Well before the RoHS directive took effect, all of our products were manufactured meeting the standards of the
European Union. With regular audits and material tests we can still assure that the components we use are
always RoHS-compliant and that the manufacturing process, as far as the state of technology allows, is
environmentally friendly.

The ROHS directive is an important step to the protection of our environment. We, as manufactures, feel
obligated to make our contribution in this respect.

A.D.J. Supply Europe B.V. – www.adj.eu – Ikon Profile User Instructions Page 14

WEEE – Waste of Electrical and Electronic Equipment

Every year thousands of tonnes of electronic components, which are harmful to the environment, end up at the
waste disposals around the world. To ensure the best possible disposal or recovery of electronic components,
the European Union has adopted the WEEE directive.

The WEEE-system (Waste of Electrical and Electronic Equipment) can be compared with the system of the

“Green Spot”, which has been in use for several years. The manufactures have to make their contribution to

the utilization of waste at the time they release the product. Money resources obtained by doing so will be
applied to develop a common system of waste management. Thereby we can ensure professional and
environmentally friendly scraping and recycling program.

As manufactures, we are part of the German system of EAR and we make our contribution towards it.
(Registration in Germany: DE41027552)
That means that products of AMERICAN DJ and AMERICAN AUDIO can be left in the collection points free of

charge and they will be used in the recycling program. Products of ELATION Professional, which are used
only by professionals, shall be handled by us. Please send Elation products directly to us at the end of their
lifetime so that we can professionally dispose of them.

Like the above ROHS, the WEEE directive is an important contribution to the environment protection and we
are glad to help to clean the environment with this disposal system.

We are happy to answer any of your inquiries and welcome your suggestions at: [e-mail]

A.D.J. Supply Europe B.V. – www.adj.eu – Ikon Profile User Instructions Page 15

NOTES

A.D.J. Supply Europe B.V. – www.adj.eu – Ikon Profile User Instructions Page 16

A.D.J. Supply Europe B.V.

Junostraat 2

6468 EW Kerkrade

The Netherlands

www.adj.eu