ADJ Ikon IR Users Manual

IKON IR

©2015 ADJ Products, LLC all rights reserved. Information,

specications, diagrams, images, and instructions herein are
subject to change without notice. ADJ Products, LLC logo and
identifying product names and numbers herein are trademarks
of ADJ Products, LLC. Copyright protection claimed includes all
forms and matters of copyrightable materials and information
now allowed by statutory or judicial law or hereinafter granted.
Product names used in this document may be trademarks or
registered trademarks of their respective companies and are
hereby acknowledged. All non-ADJ Products, LLC brands and
product names are trademarks or registered trademarks of their

respective companies.

ADJ Products, LLC and all aliated companies hereby dis­claim any and all liabilities for property, equipment, building,
and electrical damages, injuries to any persons, and direct or
indirect economic loss associated with the use or reliance of
any information contained within this document, and/or as a
result of the improper, unsafe, unsucient and negligent as­sembly, installation, rigging, and operation of this product.

8/15

User Instructions

Europe Energy Saving Notice
Energy Saving Matters (EuP 2009/125/EC)
Saving electric energy is a key to help protecting the enviroment.
Please turn o all electrical products when they are not in use. To
avoid power consumption in idle mode, disconnect all electrical
equipment from power when not in use. Thank you!

Ikon IR Introduction

Ikon IR Warranty Registration

To optimize the performance of this product, please read these operating
instructions carefully to familiarize yourself with the basic operations of
this unit. These instructions contain important safety information regard­ing the use and maintenance of this unit. Please keep this manual with the
unit, for future reference.

Unpacking:

Thank you for purchasing the Ikon IR by ADJ Products, LLC. Every Ikon
IR has been thoroughly tested and has been shipped in perfect operating
condition. Carefully check the shipping carton for damage that may have
occurred during shipping. If the carton appears to be damaged, carefully
inspect your unit for any damage and be sure all equipment necessary
to operate the system has arrived intact. In the event damage has been
found or parts are missing, please contact our toll free customer sup­port number for further instructions. Please do not return the unit to your
dealer without rst contacting customer support.

Customer Support:

ADJ Products, LLC provides a toll free customer support line, to provide
set up help and to answer any question should you encounter problems
during your set up or initial operation. You may also visit us on the web at
www.adj.com for any comments or suggestions. For service related issue
please contact ADJ Products, LLC. Service Hours are Monday through
Friday 8:00 a.m. to 4:30 p.m. Pacic Standard Time.
Voice: [phone]
Fax: [phone]
E-mail: [e-mail]

Warning! To prevent or reduce the risk of electrical shock or re, do not
expose this unit to rain or moisture.

Caution! This may cause eye damage. Avoid looking directly into the light
source. Use sensible precaution.

Caution! There are no user serviceable parts inside this unit. Do not
attempt any repairs yourself, doing so will void your manufactures war­ranty. In the unlikely event your unit may require service please contact
ADJ Products, LLC.

PLEASE do not discard the shipping carton in the trash. Please recy­cle when ever possible.

ADJ Products, LLC - www.adj.com - Ikon IR User Manual Page 2

The Ikon IR carries a two year (730 days) limited warranty. Please
fill out the enclosed warranty card to validate your purchase. All
returned service items whether under warranty or not, must be freight
pre-paid and accompany a return authorization (R.A.) number. If the
unit is under warranty you must provide a copy of your proof of pur­chase invoice. Please contact ADJ customer support for a R.A. num­ber.

Ikon IR Precautions

Safety Issue: This unit may blow the fuse if the maximum allotted

load of 7 amps is reached. If the fuse needs replacement, please see
fuse replacement on page 6.

• Be sure the local power outlet match the required voltage of the
unit.

• Disconnect from main power before making any type of connection.

• Do not remove the cover under any conditions. There are no user
serviceable parts inside.

• Always be sure to mount this unit in an area that will allow proper
ventilation. Allow about 6” (15cm) between this device and a wall.

• To reduce the risk of electrical shock or re, do not expose this unit
rain or moisture

• This unit is intended for indoor use only, use of this product out­ doors voids all warranties.

• During long periods of non-use, disconnect the unit’s main power.

• Always mount this unit in safe and stable matter.

• Power-Cord Protection - Power-supply cords should be routed
so that they are not likely to be walked on or pinched by items
placed upon or against them, paying particular attention to cords at
plugs, convenience receptacles, and the point where they exit from
the fixture. Do not attempt to remove or break o the ground prong
from the electrical cord. This prong is used to reduce the risk of
electrical shock and re in case of an internal short.

• The fixture should be serviced by qualified service personnel when:
A. The power cord or the plug has been damaged.
B. Objects have fallen, or liquid has been spilled into the appliance.
C. The appliance has been exposed to rain or water.
D. The fixture does not appear to operate normally or exhibits a
marked change in performance.

ADJ Products, LLC - www.adj.com - Ikon IR User Manual Page 3

Ikon IR Operation

Ikon IR ADJ UC IR Control

Introduction: The ADJ Ikon IR is a rotating gobo projector. This fixture
is designed for mobile DJ’s, clubs, bands, roller rinks and any arena that
requires a compact, light weight, easy to use unit. This fixture is also suitable
for theaters, studios, retail stores, and other similar locations.

Power Supply: The ADJ Ikon IR contains a automatic voltage switch, which
will auto sense the voltage when it is plugged into the power source. With this
switch there is no need to worry about the correct power voltage, this unit can
be plugged in anywhere.

Operation: This fixture is designed to operate as a stand alone, rotating
gobo projector, there is no need of a DMX controller. It has been tested and
there is no assembly necessary. The Ikon IR is ready to be plugged in out
of the box. When this fixture is plugged in, the unit will project the included
gobo. Using the bottom knob located at the back of the unit, you can make
the control the gobo rotation speed and rotation direction. The top knob will
let you control output intensity.

After plugging the unit if there is no LED output check the fuse. If the fuse
has not popped, please contact customer support for further instructions.
This fixture features a light weight case design and an adjustable hanging
bracket.

Ikon IR Installation

The unit should be mounted using a mounting clamp (not provided), axing
it to the mounting bracket that is provided with the unit. Always ensure that
the unit is rmly xed to avoid vibration and slipping while operating. Always
ensure that the structure to which you are attaching the unit is secure and
is able to support a weight of 10 times the unit’s weight. Also, always use a
safety cable that can hold 12 times the weight of the unit when installing the
xture. The equipment must be installed by a professional, and it must be
installed in a place where it is out of the reach of people’s grasp.

Ikon IR Photometric Chart

820 0 1740 76 3 430 278
566 8 1240 55 0 318 200
380 0 765 381 221 150

0m( )

43

The ADJ UC IR (sold separately) infrared remote gives you control
of various functions. To control the fixture you must aim the remote at
the front of the fixture and be no more then 30 feet away.

STAN D BY - Pressing this button will blackout the fixture.

FULL ON - This button is invalid for this fixture.

FADE/GOBO - Press this button to activate rotation.

“DIMMER +” and “DIMMER -” - Use these buttons to adjust the out-

put intensity.

1-9 - After pressing the FADE/GOBO button, these buttons will allow
you to select rotation direction and rotation speed. Press buttons 1-4
to select clockwise rotation and speed #1 button being the slowest
and #4 the fastest. Press buttons 6-9 to select counter-clockwise
rotation and speed #6 button being the slowest and #9 the fastest.
Press the #5 button to stop rotation.

SOUND ON & OFF - These button’s are invalid for this fixture.

SHOW - This button is invalid for this fixture.

Ikon IR Gobo Replacement

The Ikon IR comes with a replaceable gobo. This gobo can be interchanged
at any time and allows you to customize your system.

To replace gobo;

1. Unscrew the two screws located at the bottom that secure the gobo
housing.

2. Remove the gobo housing.

3. Once the gobo housing has been removed, remove the retaining
ring that holds the gobo in. This can easily be done using needle nose

pliers.

4. Remove and replace the gobo with your desired replacement. Reinsert
the retainer ring, and make sure the ring rests firmly against the gobo.

5. Slide the gobo assembly back into place, and secure the housing with
two screws.

Distance(m)

0

ADJ Products, LLC - www.adj.com - Ikon IR User Manual Page 4

1.0 2.0 3.0 4.0

0.443 0.887 1.33 1.774 2.217

0.573 1.147 1.72 2.294 2.867

0.788 1.576 2.363 3.151 3.939

5.0

ADJ Products, LLC - www.adj.com - Ikon IR User Manual Page 5

Ikon IR Power Cord Daisy Chain

With this feature you can connect the xtures to one another

using the IEC input and output sockets. The quantity that can

be connected is 9 fixtures maximum @ 120V and 17 fixtures
maximum @ 230V. After the maximum xture’s is reached you will
need to use a new power outlet. They must be the same xtures.
DO NOT mix xtures.

Ikon IR Trouble Shooting

No light output from the unit;

1. Be sure the fuse has not popped. The fuse is located on the rear
panel.

Ikon IR Fuse Replacement

First unplug the power. The fuse holder is located above the I.E.C
power cord output. Using a flat-head screw driver unscrew the fuse
holder. Remove the bad fuse and replace with a new one.

Ikon IR Cleaning

Fixture Cleaning:

Due to fog residue, smoke, and dust cleaning the internal and exter­nal optical lenses should be carried out periodically to optimize light
output. Cleaning frequency depends on the environment in which the
fixture operates (I.e. smoke, fog residue, dust, dew). In heavy club
use we recommend cleaning on a monthly basis. Periodic cleaning
will ensure longevity, and crisp output.

1. Use normal glass cleaner and a soft cloth to wipe down the out-

side casing.

2. Clean the external optics with glass cleaner and a soft cloth every
20 days.

3. Clean the internal optics with glass cleaner and a soft cloth every
30-60 days.

4. Always be sure to dry all parts completely before plugging the unit
back in.

ADJ Products, LLC - www.adj.com - Ikon IR User Manual Page 6

Ikon IR Warranty

MANUFACTURER’S LIMITED WARRANTY

A. ADJ Products, LLC hereby warrants, to the original purchaser, ADJ Products, LLC products
to be free of manufacturing defects in material and workmanship for a prescribed period from
the date of purchase (see specific warranty period on reverse). This warranty shall be valid only if the
product is purchased within the United States of America, including possessions and
territories. It is the owner’s responsibility to establish the date and place of purchase by acceptable
evidence, at the time service is sought.

B. For warranty service you must obtain a Return Authorization number (RA#)
before sending back the product–please contact ADJ Products, LLC Service Department
at 800-322-6337. Send the product only to the ADJ Products, LLC factory. All
shipping charges must be pre-paid. If the requested repairs or service (including
parts replacement) are within the terms of this warranty, ADJ Products, LLC will pay return
shipping charges only to a designated point within the United States. If the entire instrument is
sent, it must be shipped in it’s original package. No accessories should be shipped with the product. If
any accessories are shipped with the product, ADJ Products, LLC shall have no liability whatsoever for
loss of or damage to any such accessories, nor for the safe return thereof.

C. This warranty is void if the serial number has been altered or removed; if the product is modified in any
manner which ADJ Products, LLC concludes, after inspection, affects the reliability of the product; if the
product has been repaired or serviced by anyone other than the ADJ Products, LLC factory unless prior
written authorization was issued to purchaser by ADJ Products, LLC; if the product is damaged because
not properly maintained as set forth in the instruction manual.

D. This is not a service contract, and this warranty does not include maintnance, cleaning or periodic check
up. During the period specified above, ADJ Products, LLC will replace defective parts at its expense
with new or refurbished parts, and will absorb all expenses for warranty service and repair labor by
reason of defects in material or workmanship. The sole responsibility of ADJ Products, LLC under this
warranty shall be limited to the repair of the product, or replacement thereof, including parts, at the sole
discretion of ADJ Products, LLC. All products covered by this warranty were manufactured after August
15, 2012, and bear indentifying marks to that effect.

E. ADJ Products, LLC reserves the right to make changes in design and/or improvements upon its products
without any obligation to include these changes in any products theretofore manufactured.

No warranty, whether expressed or implied, is given or made with respect to any accessory supplied with
products described above. Except to the extent prohibited by applicable law, all implied warranties made
by ADJ Products, LLC in connection with this product, including warranties of merchantability or fitness,
are limited in duration to the warranty period set forth above. And no warranties, whether expressed or
implied, including warranties of merchantability or fitness, shall apply to this product after said period
has expired. The consumer’s and/or Dealer’s sole remedy shall be such repair or replacement as is
expressly provided above; and under no circumstances shall ADJ Products, LLC be liable for any loss or
damage, direct or consequential, arising out of the use of, or inability to use, this product.

This warranty is the only written warranty applicable to ADJ Products, LLC Products and
supersedes all prior warranties and written descriptions of warranty terms and conditions heretofore
published.

MANUFACTURER’S LIMITED WARRANTY PERIODS:

 •LightingProducts=1-year(365days)LimitedWarranty(Such as: Special Effect Lighting, Intelligent

Lighting, UV lighting, Strobes, Fog Machines, Bubble Machines, Mirror Balls, Par Cans, Trussing,
Lighting Stands etc. excluding LED and lamps)

 •LaserProducts=1Year(365Days)LimitedWarranty(excluding laser diodes which have a 6 month

limited warranty)

 •L.E.D.Products=2-year(730days)LimitedWarranty(excluding motors, PCB boards, and power
supplies, which have a 1-year (365 day Limited Warranty) batteries which have a 180 day limited war-

ranty). Only the L.E.D.s carry a 2-year warranty (excludingStarTecSerieswhichacarriesa1Year

LimitedWarranty)

•ADJDMXControllers=2Year(730Days)LimitedWarranty(excluding faders and tact switches)

ADJ Products, LLC - www.adj.com - Ikon IR User Manual Page 7

Ikon IR Notes Ikon IR Notes

ADJ Products, LLC - www.adj.com - Ikon IR User Manual Page 8

ADJ Products, LLC - www.adj.com - Ikon IR User Manual Page 9

Ikon IR Specifications

Model: Ikon IR

Voltage: 100-240V, 50/60Hz
LED: 1 x 60W
Power Consumption: 74W
Power Cord Daisy Chain: 9 Fixtures Max. (120V)

17 Fixtures Max. (230V)

Colors: White
Beam Angle: 25, 32, or 43 Degrees
Dimensions: 9.5”(L) x 9.5”(W) x 8.5”(H)
236 x 236 x 215mm
Weight: 6.6 Lbs./3 Kgs
Gobos: Size: 54mm

Viewable: 50mm

Fuse: 3.15 Amp
Duty Cycle: None
Warranty: Two Year (730 Days)

Auto Sensing Voltage: This xture contains a automatic voltage

switch, which will auto sense the voltage when it is plugged into
the power source.

Please Note: Specications and improvements in the design

of this unit and this manual are subject to change without any
prior written notice.

ADJ Products, LLC - www.adj.com - Ikon IR User Manual Page 10

ADJ Products, LLC

6122 S. Eastern Ave. Los Angeles, CA 90040 USA

Tel: [phone] / Fax: [phone]

Web: www.adj.com / E-mail: [e-mail]

A.D.J. Supply Europe B.V.

Junostraat 2

6468 EW Kerkrade

Netherlands

[e-mail] / www.adj.eu

Tel: [phone] / Fax: [phone]