ADJ Hydro Wash X7 User guide

HYDRO WASH X7

User Instructions

©2019 ADJ Products, LLC all rights reserved. Information, specications, diagrams, images, and

FCC STATEMENT
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.

FCC RADIO FREQUENCY INTERFERENCE WARNINGS & INSTRUCTIONS
This product has been tested and found to comply with the limits as per Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful interference in a residential installation.
This device uses and can radiate radio frequency energy and, if not installed and used in accordance with
the included instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this device does cause harmful
interference to radio or television reception, which can be determined by turning the device off and on, the
user is encouraged to try to correct the interference by one or more of the following methods:

· Reorient or relocate the device.

· Increase the separation between the device and the receiver.

· Connect the device to an electrical outlet on a circuit different from which the radio receiver is
connected.

· Consult the dealer or an experienced radio/TV technician for help.

instructions herein are subject to change without notice. ADJ Products, LLC logo and identifying
product names and numbers herein are trademarks of ADJ Products, LLC. Copyright protection
claimed includes all forms and matters of copyrightable materials and information now allowed by
statutory or judicial law or hereinafter granted. Product names used in this document may be
trademarks or registered trademarks of their respective companies and are hereby acknowledged.
All non-ADJ Products, LLC brands and product names are trademarks or registered trademarks of

their respective companies.

ADJ Products, LLC and all aliated companies hereby disclaim any and all liabilities for property,
equipment, building, and electrical damages, injuries to any persons, and direct or indirect economic
loss associated with the use or reliance of any information contained within this document, and/or as
a result of the improper, unsafe, unsucient and negligent assembly, installation, rigging, and operation
of this product.

DOCUMENT VERSION

Due to additional product features and/or enhancements, an updated version of this document
may be available online.
Please check www.adj.com for the latest revision/update of this manual before beginning
installation and/or programming.

Date

09/27/19

10/01/19

12/17/19

Europe Energy Saving Notice
Energy Saving Matters (EuP 2009/125/EC)

Saving electric energy is a key to help protecting the enviroment. Please turn o all electrical products when
they are not in use. To avoid power consumption in idle mode, disconnect all electrical equipment from power
when not in use. Thank you!

Document
Version

1

1.2 N/C

1.3 1.3

Software
Version >

1.0

DMX Channel
Mode

15 / 17 / 41 Initial Version

N/C

N/C Updated Display Lock/Unlock Feature

Notes

Software Update Instructions Added

Hydro Wash X7 Table of Contents

Introduction
Features I Warranty Registration
IP65 Notice
Safety Guidelines
Overview
Torque Settings & IP Tester
Torque Screw Locations
Fixture Installation

Connections

DMX Set Up
DMX Addressing

3
4
5

6

10
11
12
13

16

17
18

DMX Channel Modes

Color Macro Chart
System Menu

WiFly Control
Target Modes
Dimmer Curve Chart
Error Codes
Dimensional Drawings
Updating the Software
Power Linking I Cleaning
Limited Warranty (USA Only)

19
22
24
31
33
34
35

36

37
38
39

Technical Specications

ADJ Products, LLC - www.adj.com - Hydro Wash X7 User Manual Page 2

40

Hydro Wash X7 Introduction

Unpacking: Thank you for purchasing the Hydro Wash X7 by ADJ Products, LLC. Every Hydro Wash X7
has been thoroughly tested and has been shipped in perfect operating condition. Carefully check the
shipping carton for damage that may have occurred during shipping. If the carton appears to be damaged,
carefully inspect your xture for any damage and be sure all accessories necessary to operate the unit
has arrived intact. In the case damage has been found or parts are missing, please contact our toll free
customer support number for further instructions. Do not return this unit to your dealer without rst

contacting customer support.

Introduction: The ADJ Hydro Wash X7 is a DMX intelligent, IP rated, high powered, moving head fixture.
To optimize the performance of this product, please read these operating instructions carefully to
familiarize yourself with the basic operations of this unit.

This product is intended to be used by professionally trained personnel only and is not suitable for
private use.

These instructions contain important safety information regarding the use and maintenance of this
unit. Please keep this manual with the unit, for future reference.

Customer Support: Contact ADJ Service for any product related service and support needs. Also visit

forums.adj.com with questions, comments or suggestions.

Parts: To purchase parts online visit:

http://parts.americandj.com (US)
http://www.adjparts.eu (EU)

ADJ SERVICE USA - Monday - Friday 8:00am to 4:30pm PST
Voice: 800-322-6337 | Fax: [phone] | [e-mail]

ADJ SERVICE EUROPE - Monday - Friday 08:30 to 17:00 CET
Voice: [phone] | Fax: [phone] | [e-mail]

ADJ PRODUCTS LLC USA

6122 S. Eastern Ave. Los Angeles, CA. 90040
323-582-2650 | Fax [phone] | www.adj.com | [e-mail]

ADJ SUPPLY Europe B.V

Junostraat 2 6468 EW Kerkrade, The Netherlands
[phone] | Fax [phone]

www.adj.eu | [e-mail]

ADJ PRODUCTS GROUP Mexico

AV Santa Ana 30 Parque Industrial Lerma, Lerma, Mexico 52000
[phone]

Caution! There are no user serviceable parts inside this unit. Do not attempt any repairs yourself,
doing so will void your manufactures warranty. In the unlikely event your unit may require service
please contact ADJ Products, LLC.

PLEASE recycle the shipping carton when ever possible.

ADJ Products, LLC - www.adj.com - Hydro Wash X7 User Manual Page 3

Hydro Wash X7 Features

• IP65 Outdoor Rated

• Electronic Dimming 0-100%

• DMX-512 protocol

• IP65 Locking 5-Pin XLR Connectors In & Out

• Multiple DMX Modes

• IP65 Locking Power Connectors In & Out

• Zooming

• Multiple Unit Power Linking (See page 38)

Included:
1 x IP65 Locking Power Cable
2 x Omega Brackets

Hydro Wash X7 Warranty Registration

The Hydro Wash X7 carries a 2 year limited warranty. Please fill out the enclosed warranty card to
validate your purchase. All returned service items whether under warranty or not, must be freight pre­paid and accompany a return authorization (R.A.) number. The R.A. number must be clearly written on
the outside of the return package. A brief description of the problem as well as the R.A. number must
also be written down on a piece of paper included in the shipping carton. If the unit is under war­ranty, you must provide a copy of your proof of purchase invoice. You may obtain a R.A. number by
contacting our customer support team on our customer support number. All packages returned to the
service department not displaying a R.A. number on the outside of the package will be returned to the

shipper.

ADJ Products, LLC - www.adj.com - Hydro Wash X7 User Manual Page 4

Hydro Wash X7 IP Notice

IP65 RATED

An IP rated lighting xture is one, which is commonly installed in outdoor environments
and has been designed with an enclosure that eectively protects the ingress (entry)
of external foreign objects such as dust and water. The International Protection (IP)
rating system is commonly expressed as "IP" (Ingress Protection) followed by two
numbers (i.e. IP65) where the numbers dene the degree of protection. The rst digit
(Foreign Bodies Protection) indicates the extent of protection against particles entering
the xture and the second digit (Water Protection) indicates the extent of protection
against water entering the xture. An IP65 rated lighting xture is one, which has been
designed and tested to protect against the ingress of dust (6) and low-pressure water
jets from any direction (5).

MARINE/COASTAL ENVIRONMENT INSTALLATIONS

NOT suitable for marine and/or coastal environment installations. Installing
this xture in a marine and/or coastal environment may cause corrosion and/
or excessive wear to the interior and/or exterior components of the xture.

Damages and/or performance issues resulting from installation in a marine
and/or coastal environment will void the manufactures warranty and will NOT be subject
to any warranty claims and/or repairs.

ADJ Products, LLC - www.adj.com - Hydro Wash X7 User Manual Page 5

Hydro Wash X7 Safety Guidelines

FOR YOUR OWN PERSONAL SAFETY, PLEASE READ AND UNDERSTAND THIS MANUAL COMPLETELY

BEFORE YOU ATTEMPT TO INSTALL OR OPERATE THIS UNIT!

• THERE ARE NO USER SERVICEABLE PARTS INSIDE THIS UNIT. DO NOT ATTEMPT ANY REPAIRS
YOURSELF; DOING SO WILL VOID YOUR MANUFACTURES WARRANTY. DAMAGES RESULTING FROM
MODIFICATIONS TO THIS FIXTURE AND/OR THE DISREGARD OF SAFETY INSTRUCTIONS AND
GUIDELINES IN THIS MANUAL VOID THE MANUFACTURES WARRANTY AND ARE NOT SUBJECT TO
ANY WARRANTY CLAIMS AND/OR REPAIRS.

• DO NOT PLUG THE FIXTURE INTO A DIMMER PACK!
NEVER OPEN THIS FIXTURE WHILE IN USE!
UNPLUG POWER BEFORE SERVICING FIXTURE!
NEVER TOUCH THE FIXTURE DURING OPERATION AS IT MAY BE HOT!
KEEP FLAMMABLE MATERIALS AWAY FROM FIXTURE!

• ENSURE ALL CONNECTIONS AND END CAPS ARE PROPERLY SEALED WITH A DIELECTRIC GREASE
(AVAILABLE AT MOST ELECTRICAL SUPPLIERS) TO PREVENT WATER CORROSION AND/OR
ELECTRICAL SHORT CIRCUIT.

• IF THE FIXTURE IS EXPOSED TO ENVIRONMENTAL TEMPERATURE CHANGES SUCH AS RELOCATION
FROM AN OUTDOOR COLD TO AN INDOOR WARM ENVIRONMENT, DO NOT POWER THE FIXTURE
ON IMMEDIATELY. INTERNAL CONDENSATION AS A RESULT OF ENVIROMENTAL TEMPERATURE
CHANGE CAN CAUSE INTERNAL FIXTURE DAMAGE. LEAVE THE FIXTURE POWERED OFF UNTIL IT HAS
REACHED ROOM TEMPERATURE BEFORE POWERING ON.

• NEVER LOOK DIRECTLY INTO THE LIGHT SOURCE! RETINA INJURY RISK - MAY INDUCE BLINDNESS!
SENSITIVE PERSONS MAY SUFFER AN EPILEPTIC SHOCK!

• Be sure that the local power outlet is compatible with the required voltage for your unit.

• Do not attempt to operate this unit if the power cord has been frayed or broken.

• Do not attempt to remove or break o the ground prong from the electrical cord. This prong is used to
reduce the risk of electrical shock and re in case of an internal short.

• Disconnect from main power before making any type of connection.

• Do not remove the cover under any conditions. There are no user serviceable parts inside.

• Never operate this unit when it’s cover is removed.

• Always be sure to mount this unit in an area that will allow proper ventilation. Allow about 6” (15cm) between this
device and a wall.

• Do not attempt to operate this unit, if it becomes damaged.

• Always mount this unit in safe and stable matter.

• Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed
upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point
where they exit from the appliance.

• Cleaning -The fixture should be cleaned only as recommended by the manufacturer. See page 38 for cleaning
details.

• Heat -This fixture should be situated away from heat sources such as radiators, heat registers, stoves, or other
appliances (including amplifiers) that produce heat.

• The fixture should be serviced by qualified service personnel when the appliance does not appear to operate
normally or exhibits a marked change in performance.

ADJ Products, LLC - www.adj.com - Hydro Wash X7 User Manual Page 6

Hydro Wash X7 Safety Guidelines

PROTECTION CLASS 1 - FIXTURE MUST BE PROPERLY GROUNDED

SENSITIVE PERSONS MAY SUFFER AN EPILEPTIC SHOCK!

SAFETY G U I DELI NES

To guarantee a smooth operation, it is important to follow all instructions and guidelines in
this manual. ADJ Products, LLC is not responsible for injury and/or damages resulting
from the misuse of this fixture due to the disregard of the information printed in this
manual. Only qualified and/or certified personnel should perform installation of this fixture
and only the original rigging parts included with this fixture should be used for installation.
Any modifications to the fixture and/or the included mounting hardware will void the
original manufactures warranty and increase the risk of damage and/or personal injury.

THERE ARE NO USER SERVICEABLE PARTS INSIDE THIS UNIT.
DO NOT ATTEMPT ANY REPAIRS YOURSELF; DOING SO WILL VOID
YOUR MANUFACTURES WARRANTY. DAMAGES RESULTING FROM
MODIFICATIONS TO THIS FIXTURE AND/OR THE DISREGARD OF
SAFETY INSTRUCTIONS AND GUIDELINES IN THIS MANUAL VOID
THE MANUFACTURES WARRANTY AND ARE NOT SUBJECT TO ANY
WARRANTY CLAIMS AND/OR REPAIRS.

DO NOT PLUG FIXTURE INTO A DIMMER PACK!
NEVER OPEN THIS FIXTURE WHILE IN USE!
UNPLUG POWER BEFORE SERVICING FIXTURE!
NEVER TOUCH FIXTURE DURING OPERATION AS IT MAY BE HOT!
KEEP FLAMMABLE MATERIALS AWAY FROM FIXTURE!

ENSURE ALL CONNECTIONS AND END CAPS ARE PROPERLY
SEALED WITH A DIELECTRIC GREASE (AVAILABLE AT MOST
ELECTRICAL SUPPLIERS) TO PREVENT WATER CORROSION AND/OR
ELECTRICAL SHORT CIRCUIT.

IF THE FIXTURE IS EXPOSED TO ENVIRONMENTAL TEMPERATURE
CHANGES SUCH AS RELOCATION FROM AN OUTDOOR COLD TO AN
INDOOR WARM ENVIRONMENT, DO NOT POWER THE FIXTURE ON
IMMEDIATELY. INTERNAL CONDENSATION AS A RESULT OF
ENVIRONMENTAL TEMPERATURE CHANGE CAN CAUSE INTERNAL
FIXTURE DAMAGE. LEAVE THE FIXTURE POWERED OFF UNTIL IT
HAS REACHED ROOM TEMPERATURE BEFORE POWERING ON.

NEVER LOOK DIRECTLY INTO THE LIGHT SOURCE!
RETINA INJURY RISK - MAY INDUCE BLINDNESS!

ADJ Products, LLC - www.adj.com - Hydro Wash X7 User Manual Page 7

Hydro Wash X7 Safety Guidelines

S A FETY GUI D ELI N E S

DO NOT TOUCH the fixture housing during operation. Turn OFF the power and allow

approximately 60 minutes for the fixture to cool down before servicing.

DO NOT shake fixture; avoid brute force when installing and/or operating fixture.

DO NOT operate fixture if the power cord has become frayed, crimped, damaged and/or if any

of the power cord connectors are damaged and do not insert into the fixture securely with ease.

NEVER force a power cord connector into the fixture. If the power cord or any of its
connectors are damaged, replace it immediately with a new one of similar power rating.

DO NOT block any air ventilation slots; these must remain clean and never blocked.

Allow approx. 6” (15cm) between fixture and other devices or a wall for proper cooling.

When installing fixture in a suspended environment, always use mounting hardware that is no
less than M10 x 25 mm, and always attach an appropriately rated safety cable.

ALWAYS disconnect fixture from main power source before performing any type of service
and/or cleaning procedure. Only handle the power cord by the plug end; never pull out the
plug by tugging the wire portion of the cord.

During the initial operation of this fixture, a light smoke or smell may emit from the interior
of the fixture. This is a normal process and is caused by excess paint in the interior of the casing
burning off from the heat associated with the LED and will decrease gradually over time.

Consistent operational breaks will ensure fixture will function properly for many years.

ONLY use the original packaging and materials to transport the fixture in for service.

ADJ Products, LLC - www.adj.com - Hydro Wash X7 User Manual Page 8

Hydro Wash X7 Safety Guidelines

POTENTIAL INTERNAL FIXTURE DAMAGE FROM EXTERNAL SOURCES OF LIGHT BEAMS

External sources of light beams from direct sunlight, lighting moving head xtures, and lasers, which
are focused directly towards the exterior housing and/or penetrate the front lens opening of ADJ
lighting xtures, can cause severe internal damage including burning to optics, dichroic color lters,
glass and metal gobos, prisms, animation wheels, frost lters, iris, shutters, motors, belts, wiring,
discharge lamps, and LEDs.

This issue is not specic only to ADJ lighting xtures, it is a common issue with lighting xtures
from all manufacturers. Although there is no true way to fully prevent this issue from happening, the
guidelines below can prevent any potential damage from occurring if followed. Contact ADJ Service
for more details.

DO NOT EXPOSE THE FIXTURE AND/OR FRONT LENS OPENING TO LIGHT BEAMS FROM DIRECT
SUNLIGHT, OTHER LIGHTING MOVING HEAD FIXTURES, AND LASERS WHILE UNPACKING,
INSTALLATION, USE, AND EXTENDED IDLE TIMES OUTDOORS.
DO NOT FOCUS A LIGHT BEAM FROM ONE LIGHTING FIXTURE DIRECTLY TOWARDS ANOTHER.

ADJ Products, LLC - www.adj.com - Hydro Wash X7 User Manual Page 9

Hydro Wash X7 Overview

1. MENU Button

2. ENTER Button

3. LCD Menu Control Display

1 2 3 4 5

4. DOWN Button

5. UP Button

6. Service Port

7. IP65 Locking 5-Pin XLR Connectors In/Out

8. Gore Valve

9. IP65 Locking Power Connectors In/Out

6 7 8 9

ADJ Products, LLC - www.adj.com - Hydro Wash X7 User Manual Page 10

Hydro Wash X7 Torque Settings & IP Tester

TORQUE SETTINGS FOR SCREWS

ALL SCREWS MUST BE TIGHTENED WITH A TORQUE DRIVER. All screws are Allen Head

screws. Please see below for screw locations, screw quantity and torque settings. The number listed
in the “#” column corresponds to the location on the xture. See the xture diagram and number on
the next page for SCREW LOCATION depictions.

SCREW LOCATIONS SCREW TORQUE SETTINGS#

1 Lens Assembly to Head Casting (x6) 6.5-8.7 In-Lb

2 Lamp Cover to Head Casting (x4) 6.5-8.7 In-Lb

3 Yoke Arm Cover to Yoke Frame (8 x Each Side = 16 Total) 6.5-8.7 In-Lb

4 Access Cover to Yoke Frame (x4) Fasten by Manual Screwdriver

5 Handle to Base Casting (2 x Each Side = 4 Total) Fasten by Air Screwdriver

6 Bottom Cover to Base Casting (x12) 6.7-9.6 In-Lb

7 Power & Data Connector to Base Casting (x10) 6.5-8.7 In-Lb

8 1/4 Turn Adaptor Plate to Bottom Cover (x16) 6.5-8.7 In-Lb

TORQUE DRIVERS (Recommended):
UTICA TS-30 (Shown)

ALTERNATIVE DRIVERS:
Proto J6107A
Wiha 28887

CAUTION! DO NOT OVER TORQUE SCREWS AS THIS CAN CAUSE LEAKAGE ISSUES!
TO CONFIRM THE IP65 INTENGRITY AFTER A LAMP REPLACEMENT, TEST THE FIXTURE
USING THE ELATION IP TESTER. CONTACT ELATION SERVICE FOR MORE DETAILS.

ADJ Products, LLC - www.adj.com - Hydro Wash X7 User Manual Page 11

Hydro Wash X7 Torque Screw Locations

1

4

2

7

6

3

6

8

8

6

6

5

ADJ Products, LLC - www.adj.com - Hydro Wash X7 User Manual Page 12

Hydro Wash X7 Fixture Installation

F I XTU R E I N S T A LLA T I O N

Keep fixture at least 1.6 feet (0.5m) away from any

flammable materials, decorations, pyrotechnics, etc.

ELEC TRI C AL CONNE C T I ONS

A qualif i ed e lectri ci an sho ul d be used f or a ll

el ectri cal c onnect i ons and/ or i nst alla ti o ns.

MINIMUM DISTANCE TO OBJECTS/SURFACES

M UST BE 1.6 F EET ( 0.5 M E T ERS)

FLAMMA B LE M ATER I AL W A RNI N G

MAXIMUM TEMPERATURE OF EXTERNAL SURFACE

167° F ( 75° C )

DO NOT INSTALL THE FIXTURE IF YOU ARE NOT QUALIFIED TO DO SO!

Fixture MUST be installed following all local, national, and country commercial electrical and

construction codes and regulations. Before rigging/mounting the fixture to any metal

truss/structure or placing the fixture on any surface, a professional equipment installer

MUST be consulted to determine if the metal truss/structure or surface is properly certified

to safely hold the combined weight of the fixture, clamps, cables, and accessories.

Overhead fixture installation must always be secured with a secondary safety attachment,

such as an appropriately rated safety cable that meets all local, national, and country codes

and regulations.

Fixture maximum ambient operating temperature is 104°F. (40°C).

Do not use this fixture outside this temperature range.

Fixture should be installed in areas outside walking paths, seating areas, or away from areas

were unauthorized personnel might reach the fixture by hand.

NEVER stand directly below the fixture when rigging, removing, or servicing.

Allow approximately 15 minutes for the fixture to cool down before serving.

ADJ Products, LLC - www.adj.com - Hydro Wash X7 User Manual Page 13

Hydro Wash X7 Fixture Installation

CLAMP
(Not Included)

OMEGA
BRACKET

SAFETY CABLE
(Not Included)

OMEGA
BRACKET

Screw one clamp via a M12 screw and nut into the Omega Bracket. Insert the quick-lock fasteners
of the Omega Bracket into the respective holes of the xture base plate. NOTE: The clamp must be
attached to the Omega Bracket before attaching the bracket to the xture. Tighten the quick-
lock fasteners fully clockwise. Pull the safety-cable through the opening located on the bottom of the
unit and over the trussing system or a safe xation spot. Insert the end in the carabine and tighten
the safety screw.

ADJ Products, LLC - www.adj.com - Hydro Wash X7 User Manual Page 14

Hydro Wash X7 Fixture Installation

When installing the unit, the trussing or area of installation must be able to hold 10 times the weight
without any deformation. When installing the unit must be secured with a secondary safety attachment,
e.g. and appropriate safety cable. Never stand directly below the unit when mounting, removing, or

servicing the unit.

Overhead mounting requires extensive experience, including calculating working load limits, installation
material being used, and perodic safety inspection of all installation material and unit. If you lack
these qualications, do not attempt the installation yourself.

These installaiton should be checked by a skilled person once a year.

LCD CONTROL
DISPLAY

CABLES
DOWN

* S I D E M OUNT I N G

TO MAINTAIN IP65 RATING INTEGRITY, FIXTURE

MUST BE INSTALLED WITH CABLES FACING THE

GROUND AT ALL TIMES. WATER MUST EASILY

RUN OFF AND NOT COLLECT AROUND CABLE

CONNECTIONS.

LCD CONTROL
DISPLAY

CABLES
DOWN

* S A FETY CABL E

ALWAYS ATTACH A SAFETY CABLE WHENEVER

INSTALLING THIS FIXTURE IN A SUSPENDED

ENVIRONMENT TO ENSURE THE FIXTURE WILL

NOT DROP IF THE CLAMP FAILS.

The Hydro Wash X7 is fully operational in three dierent mounting positions, hanging upside-down,
mounted sideways on trussing, or set on a at level surface. Always use and install a safety cable as
a safety measure to prevent accidental damage and/or injury in the event the clamp fails. Never use
the carrying handles for secondary attachment.

ADJ Products, LLC - www.adj.com - Hydro Wash X7 User Manual Page 15

Hydro Wash X7 Connections

ENSURE ALL CONNECTIONS AND END CAPS ARE PROPERLY SEALED WITH A DIELECTRIC
GREASE (AVAILABLE AT MOST ELECTRICAL SUPPLIERS) TO PREVENT WATER CORROSION
AND/OR ELECTRICAL SHORT CIRCUIT.

TO MAINTAIN IP65 RATING INTEGRITY AND PREVENT WATER FROM ENTERING THE FIXTURE,
ALL UNUSED CONNECTION RUBBER CAPS MUST BE SEALED.

ADJ Products, LLC - www.adj.com - Hydro Wash X7 User Manual Page 16

Hydro Wash X7 DMX Set Up

DMX-512: DMX is short for Digital Multiplex. This is a universal protocol used as a form of communication

between intelligent fixtures and controllers. A DMX controller sends DMX data instructions from
the controller to the fixture. DMX data is sent as serial data that travels from fixture to fixture via the
DATA “IN” and DATA “OUT” XLR terminals located on all DMX fixtures (most controllers only have a
DATA “OUT” terminal).

DMX Linking: DMX is a language allowing all makes and models of dierent manufactures to be
linked together and operate from a single controller, as long as all xtures and the controller are DMX
compliant. To ensure proper DMX data transmission, when using several DMX fixtures try to use
the shortest cable path possible. The order in which fixtures are connected in a DMX line does not
influence the DMX addressing. For example; a fixture assigned a DMX address of 1 may be placed
anywhere in a DMX line, at the beginning, at the end, or anywhere in the middle. When a fixture is
assigned a DMX address of 1, the DMX controller knows to send DATA assigned to address 1 to that
unit, no matter where it is located in the DMX chain.

Data Cable (DMX Cable) Requirements (For DMX Operation): The Hydro Wash X7 can be controlled via
DMX-512 protocol. Your unit and your DMX controller requires a 5-pin XLR connector for data input and data
output. We recommend Accu-Cable DMX cables. If you are making your own cables, be sure to use
standard 110-120 Ohm shielded cable (This cable may be purchased at almost all pro lighting stores).
Your cables should be made with a male and female XLR connector on either end of the cable. Also
remember that DMX cable must be daisy chained and cannot be split.

Special Note: Line Termination.

on the last unit to avoid erratic behavior. A terminator is a 110-120 ohm 1/4 watt resistor which is con­nected between pins 2 and 3 of a male XLR connector (DATA + and DATA -). This unit is inserted in the
female XLR connector of the last unit in your daisy chain to terminate the line. Using a cable terminator
(ADJ part number Z-DMX/T) will decrease the possibilities of erratic behavior.

TO MAINTAIN IP65 RATING INTEGRITY AND PREVENT WATER FROM ENTERING THE FIXTURE,
ALL UNUSED CONNECTION RUBBER CAPS MUST BE SEALED AND ONLY IP65 RATED POWER
AND DATE CABLES MUST BE USED.

When longer runs of cable are used, you may need to use a terminator

ADJ Products, LLC - www.adj.com - Hydro Wash X7 User Manual Page 17

Hydro Wash X7 DMX Addressing

DMX ADDRESSING

All xtures should be given a DMX starting address when using a DMX controller, so the correct xture
responds to the correct control signal. This digital starting address is the channel number from which
the xture starts to “listen” to the digital control signal sent out from the DMX controller. The assignment
of this starting DMX address is achieved by setting the correct DMX address on the digital control
display on the xture.

You can set the same starting address for all xtures or a group of xtures, or set dierent addresses
for each individual xture. Setting all xtures to the same DMX address will cause all xtures to react
in the same way, in other words, changing the settings of one channel will aect all the xtures

simultaneously.

If you set each xture to a dierent DMX address, each unit will start to “listen” to the channel number
you have set, based on the quantity of DMX channels of each xture. That means changing the settings
of one channel will only aect the selected xture.

In the case of the Hydro Wash X7, when in 15 Channel you should set the starting DMX address of
the rst unit to 1, the second unit to 16 (15 + 1), the third unit to 31 (16 + 15), and so on. (See the chart
below for more details.)

Channel Mode

15 Channels 1 16 31 46

17 Channels 1 18 35 52

41 Channels 1 42 83 124

Unit1

Address

Unit2

Address

Unit3

Address

Unit4

Address

ADJ Products, LLC - www.adj.com - Hydro Wash X7 User Manual Page 18

Hydro Wash X7 DMX Channel Modes

ADJ HYDRO WASH X7

DMX Channel Values & Functions

Supports Software Version > 1.0

*Rotation direction (Clockwise/Counter-Clockwise) and control of effects depends on head orientation and Pan/Tilt settings*

15 Channels

1

2

3

5

6

7

8

17 Channels

1

2

3

4

5

6

7

8

9

10

Features subject to change without notice

41 Channels Values

1

2

3

4

5

64

000-255

000-255

000-255

000-255

000-002
003-004
005-006
007-008
009-010
011-012
013-014
015-016
017-018
019-021
022-023
024-025
026-027
028-029
030-031
032-033
034-035
036-037
038-039
040-042
043-044
045-046
047-048
049-050
051-052
053-054
055-056
057-058
059-060
061-063
064-127
128-189
190-193
194-255

Functions

PAN MOVEMENT 8-BIT

Pan Movement

PAN FINE 16-BIT

Fine Control of Pan Movement

TILT MOVEMENT 8-BIT

Tilt Movement

TILT FINE 16-BIT

Fine Control of Tilt Movement

COLORS
OPEN
COLOR 1
COLOR 2
COLOR 3
COLOR 4
COLOR 5
COLOR 6
COLOR 7
COLOR 8
COLOR 9
COLOR 10
COLOR 11
COLOR 12
COLOR 13
COLOR 14
COLOR 15
COLOR 16
COLOR 17
COLOR 18
COLOR 19
COLOR 20
COLOR 21
COLOR 22
COLOR 23
COLOR 24
COLOR 25
COLOR 26
COLOR 27
COLOR 28
COLOR 29
COLOR INDEXING
CLOCKWISE ROTATION FAST-SLOW
STOP
CLOCKWISE ROTATION SLOW-FAST

64 COLOR MACROS000-255

Please see Color Macro Chart on pages 22-23

RED 0%-100%000-255

GREEN 0%-100%000-255

BLUE 0%-100%000-255

WHITE 0%-100%000-255

ADJ Products, LLC - www.adj.com - Hydro Wash X7 User Manual Page 19

Hydro Wash X7 DMX Channel Modes

15 Channels 17 Channels

9

10

11

12

11

12

13

14

41 Channels Values

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

26

27

28

29

30

31

32

33

34

35

36

37

38

000-255

000-031
032-063
064-095
096-127
128-159
160-191
192-223
224-255

Functions

RED (1) 0%-100%

GREEN (1) 0%-100%000-255

BLUE (1) 0%-100%000-255

WHITE (1) 0%-100%000-255

RED (2) 0%-100%000-255

GREEN (2) 0%-100%000-255

BLUE (2) 0%-100%000-255

WHITE (2) 0%-100%000-255

RED (3) 0%-100%000-255

GREEN (3) 0%-100%000-255

BLUE (3) 0%-100%000-255

WHITE (3) 0%-100%000-255

RED (4) 0%-100%000-255

GREEN (4) 0%-100%000-255

BLUE (4) 0%-100%000-255

WHITE (4) 0%-100%000-255

RED (5) 0%-100%000-255

GREEN (5) 0%-100%000-255

BLUE (5) 0%-100%000-255

WHITE (5) 0%-100%000-255

RED (6) 0%-100%000-255

GREEN (6) 0%-100%000-255

BLUE (6) 0%-100%000-255

WHITE (6) 0%-100%000-255

RED (7) 0%-100%000-255

GREEN (7) 0%-100%000-255

BLUE (7) 0%-100%000-255

WHITE (7) 0%-100%000-255

SHUTTER & STROBE

SHUTTER CLOSED
SHUTTER OPEN
STROBE EFFECT SLOW-FAST
SHUTTER OPEN
PULSE EFFECT IN SEQUENCES
SHUTTER OPEN
RANDOM STROBING SLOW-FAST
SHUTTER OPEN

DIMMER 0%-100%000-255

DIMMER FINE 0%-100%000-255

ZOOM 0%-100%000-255

ADJ Products, LLC - www.adj.com - Hydro Wash X7 User Manual Page 20

Hydro Wash X7 DMX Channel Modes

NO FUNCTION

240-255

13

14

15

15

16

17

41 Channels Values15 Channels 17 Channels

DIMMER MODES:

STANDARD
STAGE
TV
ARCHITECTURAL
THEATRE
STAGE 2

DIMMER DELAY TIME

0.1Sec.

0.2Sec.

0.3Sec.

0.4Sec.

0.5Sec.

0.6Sec.

0.7Sec.

0.8Sec.

0.9Sec.

1.0Sec.

1.5Sec.

2.0Sec.

3.0Sec.

4.0Sec.

5.0Sec.

6.0Sec.

7.0Sec.

8.0Sec.

9.0Sec.
10Sec.
DEFAULT TO UNIT SETTING

PAN/TILT SPEED FAST-SLOW000-255

SPECIAL FUNCTIONS

DEFAULT LED REFRESH RATE (1200Hz)
900Hz REFRESH RATE
1000Hz REFRESH RATE
1100Hz REFRESH RATE
1300Hz REFRESH RATE
1400Hz REFRESH RATE
1500Hz REFRESH RATE
2500Hz REFRESH RATE
4000Hz REFRESH RATE
5000Hz REFRESH RATE
6000Hz REFRESH RATE
10000Hz REFRESH RATE
15000Hz REFRESH RATE
DEFAULT TO UNIT SETTING
NO FUNCTION
ENABLE BLACKOUT W/ PAN/TILT MOVEMENT
DISABLE BLACKOUT W/ PAN/TILT MOVEMENT
NO FUNCTION
PAN/TILT RESET
ZOOM RESET
NULL
ALL RESET
NULL

39

40

41

000-020
021-040
041-060
061-080
081-100
101-120

121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140

141-255

000-010

11
12
13
14
15
16
17
18
19
20
21
22

23
024-079
080-089
090-099
100-139
140-149
150-159
160-199
200-209
210-239

Functions

ADJ Products, LLC - www.adj.com - Hydro Wash X7 User Manual Page 21

Hydro Wash X7 Color Macro Chart

Color No. DMX

VAULE

OFF 0 0 0 0 0

Color1 1-4 80 255 234 80

Color2 5-8 80 255 164 80

Color3 9-12 77 255 112 77

Color4 13-16 117 255 83 83

Color5 17-20 160 255 77 77

Color6 21-24 223 255 83 83

Color7 25-28 255 243 77 77

Color8 29-32 255 200 74 74

Color9 33-36 255 166 77 77

Col or10 37-40 255 125 74 74

Color11 41-44 255 97 77 74

Color12 45-48 255 71 77 71

Color13 49-52 255 83 134 83

RED GREEN BLUE WHITE

RGBW COLOR INTENSITY

Color14 53-56 255 93 182 93

Color15 57-60 255 96 236 96

Color16 61-64 238 93 255 93

Color17 65-68 196 87 255 87

Color18 69-72 150 90 255 90

Color19 73-76 100 77 255 77

Color20 77-80 77 100 255 77

Color21 81-84 67 148 255 67

Color22 85-88 77 195 255 77

Color23 89-92 77 234 255 77

Color24 93-96 158 255 144 144

Color25 97-100 255 251 153 153

Color26 101-104 255 175 147 147

Color27 105-108 255 138 186 138

Color28 109-112 255 147 251 147

Color29 113-116 151 138 255 138

Color30 117-120

Color31 121-124 138 169 255 138

Color32 125-128 255 255 255 255

99 0 255 100

ADJ Products, LLC - www.adj.com - Hydro Wash X7 User Manual Page 22

Hydro Wash X7 Color Macro Chart

Color No. DMX

VAULE

Color33 129-132 255 206 143 0

Color34 133-136 254 177 153 0

Color35 137-140 254 192 138 0

Color36 141-144 254 165 98 0

Color37 145-148 254 121 0 0

Color38 149-152 176 17 0 0

Color39 153-156 96 0 11 0

Color40 157-160 234 139 171 0

Color41 161-164 224 5 97 0

Color42 165-168 175 77 173 0

Color43 169-172 119 130 199 0

Color44 173-176 147 164 212 0

Color45 177-180 88 2 163 0

Color46 181-184 0 38 86 0

RED GREEN BLUE WHITE

RGBW COLOR INTENSITY

Color47 185-188 0 142 208 0

Color48 189-192 52 148 209 0

Color49 193-196 1 134 201 0

Color50 197-200 0 145 212 0

Color51 201-204 0 121 192 0

Color52 205-208 0 129 184 0

Color53 209-212 0 83 115 0

Color54 213-216 0 97 166 0

Color55 217-220 1 100 167 0

Color56 221-224 0 40 86 0

Color57 225-228 209 219 182 0

Color58 229-232 42 165 85 0

Color59 233-236 0 46 35 0

Color60 237-240 8 107 222 0

Color61 241-244 0

Color62 245-248 0

0 255 0

0 0 255

Color63 249-252 0 0 0

Color64 253-255 0 255 0 0

255

ADJ Products, LLC - www.adj.com - Hydro Wash X7 User Manual Page 23

Hydro Wash X7 System Menu

SYSTEM MENU

The xture includes an easy to navigate system menu control panel display where all necessary
settings and adjustments are made. (See image below) During normal operation, pressing the MENU
button once will access the xture’s main menu. Once in the main menu, you can navigate through
the dierent functions and access the sub-menus with the UP and DOWN buttons. When you reach
a eld that requires adjusting, press the ENTER button to access that eld and use the UP and
DOWN buttons to adjust the eld. Pressing the ENTER button once more will conrm your setting.
You may exit the main menu at any time without making any adjustments by pressing the MENU

button.

SYSTEM LOCK/UNLOCK: When the display lock function is activated, the display and system
menu will lock after 10 seconds of no activity. To UNLOCK the display, press and HOLD the MENU
button for 10+ seconds.
While pressing the MENU button, a timer will appear at the bottom of the display indicating the pass­ing seconds from 0-9. Once the timer reaches 9 seconds, the display will unlock allowing access to

the system menu.

DO NOT RELEASE THE MENU BUTTON UNTIL THE DISPLAY IS UNLOCKED.

If the MENU button is released before the timer reaches 9 seconds and/or is unlocked, the display
will not unlock and the time will be reset.

NOTE: The timer will not appear in the display if the lock function is disabled.

ADJ Products, LLC - www.adj.com - Hydro Wash X7 User Manual Page 24

Hydro Wash X7 System Menu

MENU OPTIONS DESCRIPTIONSUBMENU

DMX SETTINGS

PERSONALITY

DMX Address

DMX Channel
Mode

No DMX Status

Select Signal

Status Settings

WiFly Settings

Fan Settings

Dim Modes

001-XXX

15Ch / 17Ch / 41Ch

Hold Last / Blackout / Int Programs / Manual

DMX: Yes / No

WiFly: Yes / No

WiFly and DMX Out: Yes / No

Pan Invert: On / Off

Tilt Invert: On / Off

P./T. Feedback: On / Off

P./T. Speed: Speed 1 / Speed 2

Hibernation: Off / 01M~99M / 15M

Set WiFly Channel: 00~14

Enable / Disable WiFly

Head: Auto / High / Silent (Low)

Base: Auto / High / Silent (Low)

Standard/Stage/TV/Architectural/Theatre/Stage2
Dim Speed: 0.1-0.9s ~ 1-10s

DMX Addressing

DMX Channel Mode
Selection

DMX Lost Status

Control via DMX

Control via WiFly
Control via WiFly and send

DMX Out via DMX cable

Reverse Pan Motion

Reverse Tilt Motion

Pan/Tilt Movement Feedback

Pan/Tilt Movement Speed

Sleep Setting (No Activity)

Set WiFly Wireless Channel

Activate / Deactivate WiFly

Head Fan Speed Setting

Base Fan Speed Setting

Dimming Curve Modes
Dimming Speed

900Hz / 1000Hz / 1100Hz / 1200Hz / 1300Hz /

LED Refresh Rate

Gamma 1.0 / 2.0 / 2.2 / 2.4 / 2.6 / 2.8 Gamma Brightness

Reset Motors

Display

Service

(Pass Code = 050)

1400Hz / 1500Hz / 2500Hz / 4000Hz /5000Hz /
6000Hz / 10000Hz / 15000Hz

Reset All Motor: YES / NO

Pan/Tilt Reset: YES / NO

Zoom Reset: YES / NO

Intensity: 1~10 (Dimmest-Brightest)

Display Invert: YES / NO

Screen Saver Delay: OFF~10M

Lock On/Off: ON / OFF Display Control Lock

Calibration - Pass Code = 050

USB Port Power: ON / OFF

Update Software

Factory Restore: YES / NO - Pass Code = 011

LED Refresh Setting

Reset All Motors

Reset the Pan & Tilt Motors

Reset the Zoom Motor

Display Intensity Adjustment

Display Inversion

Display Blackout Time

Calibration/Adjustments

USB Port Activation

Software Update

Restore Factory Settings

ADJ Products, LLC - www.adj.com - Hydro Wash X7 User Manual Page 25

Hydro Wash X7 System Menu

MENU OPTIONS DESCRIPTIONSUBMENU

Mode

MODE 1 (001)

Pan
Tilt
Color
Red 1-7
Green 1-7
Blue 1-7
White 1-7
Color Macros
Shutter
Dimmer

MANUAL
CONTROL

Zoom
Spe. Func

MODE 2 (002)

Pan
Tilt
Colors
All Red
All Green
All Blue
All White
Color Macros
Shutter
Dimmer
Zoom
Spe. Func

Program 0

INTERNAL
PROGRAMS

Program 1
Program 2
Program 3
Program 4

Target Mode Mode 0 / Mode 1 / Mode 2 / Mode 3 / Mode 4Target Mode Target Mode

Fixture Life Time

001 / 002

000-255
000-255
000-255
000-255
000-255
000-255
000-255
000-255
000-255
000-255
000-255
000-255

000-255
000-255
000-255
000-255
000-255
000-255
000-255
000-255
000-255
000-255
000-255
000-255

Speed: 000~255 Fade: 000~255
Speed: 000~255 Fade: 000~255
Speed: 000~255 Fade: 000~255
Speed: 000~255 Fade: 000~255
Speed: 000~255 Fade: 000~255

Power On Time - XXXXXX Hours

P-On Time-R - XXXXXX Hours

Manual Control

Program 0 with Adjustments
Program 1 with Adjustments
Program 2 with Adjustments
Program 3 with Adjustments
Program 4 with Adjustments

Total Running Time
(Not Resettable)

Total Running Time
(Resettable)

Information

Total LED Time

P-On Time Reset - Pass Code = 050

LED On Time - XXXXXX Hours

LED On Time-R - XXXXXX Hours

LED On Time Reset - Pass Code = 050

Reset Total Running Time

Total LED On Running
Time (Not Resettable)

LED On Running Time
(Resettable)

Reset LED Running Time

ADJ Products, LLC - www.adj.com - Hydro Wash X7 User Manual Page 26

Hydro Wash X7 System Menu

MENU OPTIONS DESCRIPTIONSUBMENU

Current: XXX ˚F / XXX ˚C

Max Resettable: XXX ˚F / XXX ˚C

LED’s

Max Not Resettable: XXX ˚F / XXX ˚C

Current LED Temperature

Maximum Temperature

(1)

Reached (Resettable)

(See Note 1)

Maximum Temperature

(2)

Reached (Not Resettable)

(See Note 2)

Current: XXX ˚F / XXX ˚C

Current Head Temperature

Maximum Temperature

Head

Max Resettable: XXX ˚F / XXX ˚C

Reached (Resettable)

(See Note 1)

Maximum Temperature

Fixture Temps

Max Not Resettable: XXX ˚F / XXX ˚C

Current: XXX ˚F / XXX ˚C

Reached (Not Resettable)

(See Note 2)

Current Base Temperature

Maximum Temperature

Information

Max Resettable: XXX ˚F / XXX ˚C

Base

Reached (Resettable)

(See Note 1)

Maximum Temperature

Max Not Resettable: XXX ˚F / XXX ˚C

Reset LED Temp: Pass Code = 050

Reset Head Temp: Pass Code = 050

Reset Base Temp: Pass Code = 050

Head Humidity: XXX%

Reached (Not Resettable)

(See Note 2)

Reset LED Temperature
(Max Resettable)

Reset Head Temperature
(Max Resettable)

Reset Head Temperature
(Max Resettable)

Current Head Humidity

Humidity

Fan Info. (RPM)

Base Humidity: XXX%

LED Fan: XXXX

Base Fan: XXXX

Current Base Humidity

Current LED Fan Speed

Current Base Fan Speed

Arm Fan: XXXX Current Arm Fan Speed

Pan / Pan Fine / Tilt / Tilt Fine / Color /

DMX Values

(See Note 3)

(3)

Color Macros / Red 1-7 / Green 1-7 /
Blue 1-7 / White 1-7 / Shutter / Dimmer /
Dimmer Fine / Zoom / Dimmer Modes /

Current DMX Values

P/T Speed / Spe. Func

Error Logs

Max Temp LED ON

High Temp LED
OFF

Fixture Errors (Listed Errors One by One)

Reset Error Log: Yes / No (Pass Code = 050)

32~169˚F, 99˚F

(See Note 4 below)

170˚F, 99˚F

(See Note 5 below)

(5)

/ 77˚C, 37˚C

(4)

/ 0~76˚C, 37˚C

(4)

(5)

Last 10 Fixture Error Codes

Clear the Error Log

Fixture Temp. (LED On)

Fixture Temp. (LED Off)

VX.XSoftware Version Current Software Version

(1) Current Maximum Temperature - Maximum temp. that has been recorded, before reset and after reset.
(2) Maximum Temperature - Overall maximum temp. that has been recorded. (Not Resettable)
(3) DMX Value settings depend on the DMX Channel mode the fixture is set to.
(4) Max Temp LED ON - Normal Operating Temperature
(5) Max Temp LED OFF - Normal Operating Temperature

(1)

(2)

(1)

(2)

ADJ Products, LLC - www.adj.com - Hydro Wash X7 User Manual Page 27

Hydro Wash X7 System Menu

DMX SETTINGS - The submenus listed under DMX SETTINGS are as follows: DMX Address,
DMX Channel Mode, and No DMX Status.

- DMX ADDRESS - In this submenu you can nd and set your desired DMX address.

- DMX CHANNEL MODE - In this submenu you can nd and set your desired DMX channel mode.

- NO DMX STATUS - This submenu setting is used as a precaution mode in case the DMX signal is

lost or interrupted. The operating mode chosen in this submenu is the running mode the xture
will go into when the DMX signal is lost. Listed below are the 3 modes.

• Hold Last - This setting will have the xture stay in the last DMX setup.

• Blackout - This setting will have the xture automatically go into stand by mode.

• Manual - This setting will go into the current manual control set up. See MANUAL CONTROL.

PERSONALITY - The submenus listed under PERSONALITY are as follows: Select Signal, Status
Settings, WiFly Settings, Reset Motors, Display, and Service.

- SELECT SIGNAL - In this submenu you can select your desired DMX control mode:

• DMX - Control the unit via DMX cable connection.

• WiFly - Control the unit via WiFly.

• WiFly and DMX Out - Control the unit via WiFly connection. The DMX signal is sent to the next
unit via DMX cable.

- STATUS SETTINGS - In this submenu you are able to access and adjust/change: Pan Invert, Tilt
Invert, P./T. Feedback, P./T. Speed, and Hibernation.

- WIFLY SETTINGS - In this submenu you are able to access and adjust/change: WiFly Channel setting
and Enable/Disable WiFly.

- FAN SETTINGS - In this submenu you are able to select your desired fan speed settings for both
the head and base fans.

- DIM MODES - In this submenu you are able to select your desired dimmer mode and adjust the
dimming speed time. See page 34 for the dimmer curve chart.

- LED REFRESH RATE - In this submenu you are able to select your desired LED refresh rate.

- GAMMA - In this submenu you are able to select your desired gamma setting.

- RESET MOTORS - In this submenu you are able to reset selected motors.

- DISPLAY - In this submenu you are able to access and adjust/change the backlight intensity, display

inversion, screen saver display time, and display lock function.

ADJ Products, LLC - www.adj.com - Hydro Wash X7 User Manual Page 28

Hydro Wash X7 System Menu

- SERVICE - In this submenu you are able to access the calibration adjustment, USB port power on/o,
software update, and restore the factory settings.

NOTE: To update the software please see page 37 for more details.

MANUAL CONTROL - This menu is for manual testing and manual control. Under MANUAL CONTROL
the xture has two control modes; “MODE 1” and “MODE 2”.

NOTE: NO DMX STATUS must be set to “Manual” when using Manual Control.

INTERNAL PROGRAMS - This menu allows you to select 1 of 4 (0-4 internal programs to run. Program
speed and fade speed are adjustable. The selected program will also run when “Int Program.” is
selected under the “NO DMX STATUS” setting.

TARGET MODE - Target mode is a restrictive pan/tilt control limiting the movement to a certain
degree. See page 33 for a diagram of the Target mode movements.

INFORMATION - The submenus listed under INFORMATION are as follows: Fixture Life Time,
Total LED Time, Fixture Temps, Humidity, Fan Info. (RPM), DMX Values, Error Logs, Max Temp LED
ON, High Temp LED OFF, and Software Version.

- FIXTURE LIFE TIME

• Power On Time -The TOTAL power ON running time of the unit is displayed. This time CANNOT
be reset.

• P-On Time-R - The CURRENT power ON running time of the unit is displayed. This running time
may not be the same as the total power ON running time displayed under “Power On Time”. This

time CAN be reset. NOTE: The displayed time represents the current power ON time since the
last reset.

• P-On Time Reset - Reset the CURRENT power ON running time that is displayed under “P-On Time-R”.

- TOTAL LED TIME

• LED On Time - The TOTAL LED ON time is displayed. This total LED ON time CANNOT be reset.
NOTE: The displayed time represents the TOTAL LED ON time.

• LED On Time-R - The CURRENT LED ON running time is displayed. This running time may not
be the same as the total LED ON time displayed under “LED On Time”. This total LED ON time

CAN be reset. NOTE: The displayed time represents the CURRENT LED ON time since the last
reset.

• LED On Time Reset - With this function you can reset the CURRENT LED ON time that is displayed
under “LED On Time-R”.

ADJ Products, LLC - www.adj.com - Hydro Wash X7 User Manual Page 29

Hydro Wash X7 System Menu

- FIXTURE TEMPS

• LED’s
Current - Current temperature of the LED’s is displayed.
Max Resettable - Maximum LED temperature that has been recorded, before reset and after
reset. (Resettable)
Max Not Resettable - Overall maximum LED temperature that has been recorded.
(Not Resettable)

• Head
Current - Current temperature of the head is displayed.

Max Resettable - Maximum base temperature that has been recorded, before reset and after
reset. (Resettable)
Max Not Resettable - Overall maximum moving head temperature that has been recorded.
(Not Resettable)

• Base
Current - Current temperature of the base is displayed.

Max Resettable - Maximum base temperature that has been recorded, before reset and after
reset. (Resettable)
Max Not Resettable - Overall maximum moving base temperature that has been recorded.
(Not Resettable)

• Reset LED Temp - Reset the LED temperature reading.

• Reset head Temp - Reset the head temperature reading.

• Reset Base Temp - Reset the base temperature reading.

- HUMIDITY

• Head Humidity - The current humidity of the moving head is displayed.

• Base Humidity - The current humidity of the base is displayed.

- FAN INFO. (RPM) - In this submenu the current LED, base, and arm fan speed will be displayed.

- DMX VALUES - Displays the DMX values of any DMX channel that is currently in use. NOTE: DMX
value options depend on the current DMX channel mode setting.

- ERROR LOGS - In this submenu you are able to check any unit errors as well as clear the error log.

- MAX TEMP LED ON - In this submenu you are able to check the normal operating temperatures as

well as the current temperature of the xture.

- HIGH TEMP LED OFF - In this submenu you are able to check the normal operating temperatures
as well as the current temperature of the xture.

- SOFTWARE VERSION - Current software version is displayed.

ADJ Products, LLC - www.adj.com - Hydro Wash X7 User Manual Page 30

Hydro Wash X7 WiFly Control

BEFORE SETTING THE WIRELESS CHANNEL ON ANY WIFLY FIXTURE, MAKE SURE
THE SOURCE WIFLY WIRELESS DMX TRANSCEIVER DEVICE IS OFF.

With this feature you are able to control the unit with DMX without the need of XLR cables. Your
DMX controller must be connected to a ADJ WiFly Transceiver to use this function. You are able to
communicate up to 2500 feet/760 meters (open line of sight).

1. Ensure the source WiFly wireless DMX Transceiver device is powered OFF.

2. Power ON the fixture and using the control panel scroll to the PERSONALITY menu and press

ENTER. Use the UP and DOWN buttons to highlight the WIFLY SETTINGS submenu and press
ENTER.

3. Using the UP and DOWN buttons, highlight ENABLE/DISABLE WIFLY. Press the ENTER button
to toggle between ENABLE & DISABLE. Press ENTER so that “ENABLE” is displayed.

4. Next highlight SET WIFLY CHANNEL and press ENTER. Use the UP and DOWN buttons to find
your desired WiFly address and press ENTER to confirm.

NOTE: Erratic fixture movement may occur if other WiFly wireless DMX products are in use in
the same area and are using the same WiFly wireless channel. When WiFly is enabled, the fixture
may immediately start to respond to the DMX wireless signal from another WiFly wireless DMX
Transceiver. Make sure to know what WiFly wireless channels are being used in the area where the
fixture is being used.

ADJ WIFLY WIRELESS TRANSCEIVER only has 0-14 wireless channels, NO CH 15.

5. Set your desired DMX address in the DMX ADDRESS submenu of the DMX SETTINGS main system
menu. Set your desired DMX channel mode in the DMX CHANNEL MODE submenu of the
DMX SETTINGS main system menu.

6. Repeat this process for all WiFly compatible fixtures in the WiFly wireless network, making sure
all fixtures are assigned the same WiFly wireless channel.

7. After all fixtures in the WiFly wireless network have been set to the same WiFly wireless channel
and powered ON, power ON the source WiFly DMX Transceiver device.

8. Test all fixtures connected to the WiFly wireless network to confirm proper functionality.

ADJ Products, LLC - www.adj.com - Hydro Wash X7 User Manual Page 31

Hydro Wash X7 WiFly Control

WIRELESS WIFLY INSTALLATION LOCATION GUIDELINES

Wireless DMX signal can penetrate walls, glass, metal, and most objects. However, there are many
factors that can aect and/or interrupt the wireless DMX signal, one of which is people. Therefore, it
is highly recommended to position the wireless antenna a minimum of 9.8 ft. (3m) above audiences
and/or above ground level. Careful planning and testing of the selected installation location is critical
to ensure optimum and reliable wireless DMX operation.

9.8 ft (3m)

Above Ground

ADJ Products, LLC - www.adj.com - Hydro Wash X7 User Manual Page 32

Hydro Wash X7 Target Modes

Mode 0:

Mode 1: Pan Movement Range: 90º Tilt Movement Range: 135º

Mode 2:

Pan Movement Range: 540º Tilt Movement Range: 270º

Pan Movement Range: 90º Tilt Movement Range: 135º

Mode 3:

Mode 4:

Pan Movement Range: 90º Tilt Movement Range: 135º

Pan Movement Range: 90º Tilt Movement Range: 135º

ADJ Products, LLC - www.adj.com - Hydro Wash X7 User Manual Page 33

Hydro Wash X7 Dimmer Curve Chart

DIMMER

100%

50%

10%

0%

Time (ms)

255 255

0 0

Stage 780 1100 1540 1660

TV 1180 1520 1860 1940

Architectural 1380 1730 2040 2120

0 sec Fade Time

1 sec Fade Time

0 Sec

Rise Time Down Time

Dimming Curve

Ramp Effect

Rise Time (ms) Down Time (ms) Rise Time (ms) Down Time (ms)

Standard (default) 0 0 0 0

Theatre 1580 1940 2230 2280

Stage 2

0 1100 0 1660

ADJ Products, LLC - www.adj.com - Hydro Wash X7 User Manual Page 34

Hydro Wash X7 Error Codes

1

2

3

4

5

6

7

8

9

10

11

PRINT ERROR MESSAGE DESCRIPTION

HeadFan speed too fast HeadFan speed too fast

   

CPU-B Error CPU-B Error

CPU-C Error CPU-C Error

CPU-D Error CPU-D Error

Pan Reset Error

Pan Encode Error

Tilt Reset Error

Tilt Encode Error

Zoom Reset Error

HeadFan Start Error HeadFan can't start

HeadFan Stop Error HeadFan can't stop

Pan: Reset Error

Pan: Encode Error

Tilt: Reset Error

Tilt: Encode Error

Zoom: Reset Error

12

13

14

15

16

17

18

19

20

HeadFan speed too slow HeadFan speed too slow

BaseFan Start Error BaseFan can't start

BaseFan Stop Error BaseFan can't stop

BaseFan speed too fast BaseFan speed too fast

BaseFan speed too slow BaseFan speed too slow

ArmFan Start Error ArmFan can't start

ArmFan Stop Error ArmFan can't stop

Led Temp: Too High

Led Temp Error

Led Temp: Too High

Led Temp Error

ADJ Products, LLC - www.adj.com - Hydro Wash X7 User Manual Page 35

Hydro Wash X7 Dimensional Drawings

6.41” / 163mm

10.17” / 258.3mm

8.26” / 210mm

16.09” / 408.8mm

7.73” / 196.5mm

18” / 457mm

11.89” / 302.1mm

11.32” / 287.6mm

ADJ Products, LLC - www.adj.com - Hydro Wash X7 User Manual Page 36

Hydro Wash X7 Updating the Software

ONLY QUALIFIED TECHNICIANS SHOULD PERFORM THIS FUNCTION!
NOTE ALL MENU SETTINGS BEFORE UPDATING SOFTWARE!
FIXTURE SOFTWARE CAN NOT BE DOWNGRADED!
DOWNLOAD FIXTURE SOFTWARE TO PC ONLY! (NO MAC SUPPORT)
PLEASE CONTACT ADJ CUSTOMER SERVICE FOR FURTHER INFORMATION.

1. Contact ADJ Customer Service to obtain the software update les.

2. Copy the software les to a compatiable USB ash drive.

NOTE: MAKE SURE THESE SOFTWARE FILES ARE THE ONLY FILES LOADED ONTO THE
USB FLASH DRIVE.

3. Disconnect DMX and WiFly connections and power the xture ON.

4. Insert the USB ash drive into the SERVICE PORT located on the rear panel of the unit.

5. Locate “PERSONALITY” within the system menu and press ENTER. Scroll to the “SERVICE”
submenu and press ENTER. Enter the passcode “50” to gain access.

6. Scroll to the “USB PORT POWER” setting and activate the USB service port by selecting ON.

NOTE: The USB port is OFF by default.

7. After activating the USB port, scroll to “UPDATE SOFTWARE” and press ENTER.

8. Two (2) software les will be displayed as downloaded earlier. Highlight the rst le and press ENTER.
Select YES to begin the rst of two updating processes. Once YES is selected the display
will show “Updating, Please wait...”. A percentage bar will also be displayed.

9. After the rst update is complete, the xture will run a software check (this can take some time).

10. After the software check is complete, the xture will peform a reset.

11. Once the reset is complete, scroll to the “PERSONALITY” menu again and press ENTER. Scroll
to the “SERVICE” submenu and press ENTER. Enter the passcode “50” to gain access.

12. Reactivate the USB port power if necessary. (See step 6)

13. Scroll to “UPDATE SOFTWARE” setting again and press ENTER.

14. Highlight the second le this time and press ENTER. Select YES to begin the second and nal
updating process. Once YES is selected the display will show “Updating, Please wait...”.
A percentage bar will also be displayed.

15. After the second update is complete, the xture will run a software check again.

16. After the software check is complete, the xture will peform another reset.

17. Remove the USB ash drive.

18. After the reset process is complete check the new software version to conrm it is updated to the
most recent software.

ADJ Products, LLC - www.adj.com - Hydro Wash X7 User Manual Page 37

Hydro Wash X7 Multiple Unit Power Linking

With this feature you can connect the xtures to one another using the power cable input and

output sockets.
NOTE: USE CAUTION WHEN POWER LINKING OTHER FIXTURES AS THE POWER
CONSUMPTION OF OTHER MODEL FIXTURES MAY EXCEED THE MAX POWER OUTPUT ON
THIS FIXTURE! CHECK SILK SCREEN FOR MAX AMPS.

Hydro Wash X7 Cleaning

Due to fog residue, smoke, and dust cleaning the internal and external optical lenses must be car­ried out periodically to optimize light output.

1. Use normal glass cleaner and a soft cloth to wipe down the outside casing.

2. Clean the external optics with glass cleaner and a soft cloth every 20 days.

3. Always be sure to dry all parts completely before plugging the unit back in.
Cleaning frequency depends on the environment in which the fixture operates (i.e. smoke, fog residue,
dust, dew).

ADJ Products, LLC - www.adj.com - Hydro Wash X7 User Manual Page 38

Hydro Wash X7 Limited Warranty (USA Only)

MANUFACTURER’S LIMITED WARRANTY

A. ADJ Products, LLC hereby warrants, to the original purchaser, ADJ Products, LLC products to be free of manufacturing

defects in material and workmanship for a prescribed period from the date of purchase (see specific warranty period
on reverse). This warranty shall be valid only if the product is purchased within the United States of America, including
possessions and territories. It is the owner’s responsibility to establish the date and place of purchase by acceptable
evidence, at the time service is sought.

B. For warranty service you must obtain a Return Authorization number (RA#) before sending back the product–please

contact ADJ Products, LLC Service Department at 800-322-6337. Send the product only to the ADJ Products, LLC
factory. All shipping charges must be pre-paid. If the requested repairs or service (including parts replacement) are
within the terms of this warranty, ADJ Products, LLC will pay return shipping charges only to a designated point
within the United States. If the entire instrument is sent, it must be shipped in it’s original package. No accessories
should be shipped with the product. If any accessories are shipped with the product, ADJ Products, LLC shall
have no liability whatsoever for loss of or damage to any such accessories, nor for the safe return thereof.

C. This warranty is void if the serial number has been altered or removed; if the product is modified in any manner

which ADJ Products, LLC concludes, after inspection, affects the reliability of the product; if the product has been
repaired or serviced by anyone other than the ADJ Products, LLC factory unless prior written authorization was issued
to purchaser by ADJ Products, LLC; if the product is damaged because not properly maintained as set forth in the

instruction manual.

D. This is not a service contract, and this warranty does not include maintnance, cleaning or periodic check up.

During the period specified above, ADJ Products, LLC will replace defective parts at its expense with new or
refurbished parts, and will absorb all expenses for warranty service and repair labor by reason of defects in material or
workmanship. The sole responsibility of ADJ Products, LLC under this warranty shall be limited to the repair of the
product, or replacement thereof, including parts, at the sole discretion of ADJ Products, LLC. All products covered
by this warranty were manufactured after August 15, 2012, and bear indentifying marks to that effect.

E. ADJ Products, LLC reserves the right to make changes in design and/or improvements upon its products without

any obligation to include these changes in any products theretofore manufactured.

No warranty, whether expressed or implied, is given or made with respect to any accessory supplied with products

described above. Except to the extent prohibited by applicable law, all implied warranties made by ADJ Products,
LLC in connection with this product, including warranties of merchantability or fitness, are limited in duration to the
warranty period set forth above. And no warranties, whether expressed or implied, including warranties of merchantability or
fitness, shall apply to this product after said period has expired. The consumer’s and/or Dealer’s sole remedy shall
be such repair or replacement as is expressly provided above; and under no circumstances shall ADJ Products,
LLC be liable for any loss or damage, direct or consequential, arising out of the use of, or inability to use, this
product.

This warranty is the only written warranty applicable to ADJ Products, LLC Products and supersedes all prior warranties

and written descriptions of warranty terms and conditions heretofore published.

MANUFACTURER’S LIMITED WARRANTY PERIODS:

• Non L.E.D. Lighting Products = 1-year (365 days) Limited Warranty (Such as: Special Effect Lighting, Intelligent
Lighting, UV lighting, Strobes, Fog Machines, Bubble Machines, Mirror Balls, Par Cans, Trussing, Lighting Stands
etc. excluding LED and lamps)

• Laser Products = 1 Year (365 Days) Limited Warranty (excluding laser diodes which have a 6 month limited
warranty)

• L.E.D. Products = 2-year (730 days) Limited Warranty (excluding batteries which have a 180 day limited warranty).

Note: 2 Year Warranty only applies to purchases within the United States.

• StarTec Series = 1 Year Limited Warranty (excluding batteries which have a 180 day limited warranty).

• ADJ DMX Controllers = 2 Year (730 Days) Limited Warranty

ADJ Products, LLC - www.adj.com - Hydro Wash X7 User Manual Page 39

Hydro Wash X7 Technical Specifications

Voltage: 100V ~ 240V/50~60Hz
IP Rating: IP65
LEDs: 7 x Osram 40W RGBW (4-in-1) LEDs
Power Draw: 370W
Weight: 35 lbs./ 16 kgs.
Dimensions: 11.89” (L) x 10.17” (W) x 18” (H)
302 x 258.3 x 457mm
DMX Channels: 3 DMX Modes: 15 / 17 / 41
Warranty: 2 Year (730 days)

Please Note: Specications and improvements in the design of this unit and this

manual are subject to change.

ADJ Products, LLC - www.adj.com - Hydro Wash X7 User Manual Page 40