ADJ Hydro Spot 1 User guide

HYDRO SPOT 1

User Manual

©2022 ADJ Products, LLC all rights reserved. Information, specications, diagrams, images, and

instructions herein are subject to change without notice. ADJ Products, LLC logo and identifying prod­uct names and numbers herein are trademarks of ADJ Products, LLC. Copyright protection claimed
includes all forms and matters of copyrightable materials and information now allowed by statutory or
judicial law or hereinafter granted. Product names used in this document may be trademarks or regis­tered trademarks of their respective companies and are hereby acknowledged. All non-ADJ Products,
LLC brands and product names are trademarks or registered trademarks of their respective compa­nies.

ADJ Products, LLC and all afliated companies hereby disclaim any and all liabilities for property,

equipment, building, and electrical damages, injuries to any persons, and direct or indirect economic
loss associated with the use or reliance of any information contained within this document, and/or as
a result of the improper, unsafe, insufcient and negligent assembly, installation, rigging, and opera­tion of this product.

DOCUMENT VERSION

Due to additional product features and/or enhancements, an updated version of
this document may be available online.
Please check www.adj.com for the latest revision/update of this manual
before beginning installation and/or programming.

Date

06/30/2022 1.0 1.01 17 / 20 / 22 ch. Initial Release

Europe Energy Saving Notice
Energy Saving Matters (EuP 2009/125/EC)
Saving electric energy is a key to help protecting the enviroment. Please turn off all electrical products when
they are not in use. To avoid power consumption in idle mode, disconnect all electrical equipment from power
when not in use. Thank you!

Document

Version

Software

Version

DMX Channels Notes

2

TABLE OF CONTENTS

Introduction 4
Limited Warranty (USA Only) 5
Warranty Registration | Features 6
Safety Precautions 7
Overview 9
Installation 10
Remote Device Management (RDM) 13
Color Wheels 14
Gobos 15
Control Panel 18
System Menu 19
DMX Set Up 22
DMX Traits 24
Dim Speeds 31
Dim Modes 32
Primary-Secondary Set Up | Multi Unit Power Linking 33
Maintenance Guidelines 34
Torque Settings for Screws 35
Error Codes 37
Dimensional Drawings 38
Specifications 39

3

INTRODUCTION

Unpacking: Thank you for purchasing the Hydro Spot 1 by ADJ Products, LLC. Every device has been
thoroughly tested and has been shipped in perfect operating condition. Carefully check the shipping
carton for damage that may have occurred during shipping. If the carton appears to have been dam-

aged, carefully inspect your xture for any damage and be sure all accessories necessary to operate

the unit have arrived intact. In the event that damage has been found or parts are missing, please con­tact our toll free customer support number for further instructions. Do not return this unit to your dealer

without rst contacting customer support.

Introduction: The ADJ Hydro Spot 1 is a feature-packed, LED-powered moving head spot luminaire
housed within a robust IP65-rated housing. This product is intended to be used by professionally

trained personnel only and is not suitable for private use.

Customer Support: Contact ADJ Service for any product related service and support needs. Also visit

forums.adj.com with questions, comments or suggestions.

Parts: To purchase parts online visit:

http://parts.adj.com (US)
http://www.adjparts.eu (EU)

ADJ SERVICE USA - Monday - Friday 8:00am to 4:30pm PST
Voice: 800-322-6337 | Fax: [phone] | [e-mail]

ADJ SERVICE EUROPE - Monday - Friday 08:30 to 17:00 CET
Voice: [phone] | Fax: [phone] | [e-mail]

ADJ PRODUCTS LLC USA

6122 S. Eastern Ave. Los Angeles, CA. 90040

323-582-2650 | Fax [phone] | www.adj.com | [e-mail]

ADJ SUPPLY Europe B.V

Junostraat 2 6468 EW Kerkrade, The Netherlands

[phone] | Fax [phone]

www.americandj.eu | [e-mail]

ADJ PRODUCTS GROUP Mexico

AV Santa Ana 30 Parque Industrial Lerma, Lerma, Mexico 52000

[phone]

CAUTION! There are no user serviceable parts inside this unit. Do not attempt any repairs yourself,

as doing so will void your manufacturer’s warranty. In the unlikely event your unit may require service,

please contact ADJ Products, LLC.

Do not discard the shipping cartoon in the trash. Please recycle when ever possible.

4

LIMITED WARRANTY (USA ONLY)

A. ADJ Products, LLC hereby warrants, to the original purchaser, ADJ Products, LLC products to be free of

manufacturing defects in material and workmanship for a prescribed period from the date of purchase (see

specic warranty period on reverse). This warranty shall be valid only if the product is purchased within the
United States of America, including possessions and territories. It is the owner’s responsibility to establish

the date and place of purchase by acceptable evidence, at the time service is sought.

B. For warranty service, you must obtain a Return Authorization number (RA#) before sending the product

back—please contact ADJ Products, LLC Service Department at 800-322-6337. Send the product only to
the ADJ Products, LLC factory. All shipping charges must be prepaid. If the requested repairs or service
(including parts replacement) are within the terms of this warranty, ADJ Products, LLC will pay return ship­ping charges only to a designated point within the United States. If the entire instrument is sent, it must be
shipped in its original package and packaging material. No accessories should be shipped with the product.
If any accessories are shipped with the product, ADJ Products, LLC shall incur no liability whatsoever for
loss of or damage to any such accessories, nor for the safe return thereof.

C. This warranty is void if the product serial number and/or labels are altered or removed; if the product is

modied in any manner which ADJ Products, LLC concludes, after inspection, affects the reliability of the

product; if the product has been repaired or serviced by anyone other than the ADJ Products, LLC factory
unless prior written authorization was issued to purchaser by ADJ Products, LLC; if the product is dam­aged because it was not properly maintained as set forth in the product instructions, guidelines and/or user
manual.

D. This is not a service contract, and this warranty does not include maintenance, cleaning, or periodic check-

up. During the period specied above, ADJ Products, LLC will replace defective parts at its expense with
new or refurbished parts, and will absorb all expenses for warranty service and repair labor by reason of

defects in material or workmanship. The sole responsibility of ADJ Products, LLC under this warranty shall
be limited to the repair of the product, or replacement thereof, including parts, at the sole discretion of ADJ
Products, LLC. All products covered by this warranty were manufactured after August 15, 2012, and bear
identifying marks to that effect.

E. ADJ Products, LLC reserves the right to make changes in design and/or improvements upon its products

without any obligation to include these changes in any products theretofore manufactured.

F. No warranty, whether expressed or implied, is given or made with respect to any accessory supplied with

products described above. Except to the extent prohibited by applicable law, all implied warranties made by
ADJ Products, LLC in connection with this product, including warranties of merchantability or tness, are
limited in duration to the warranty period set forth above. And all warranties, whether expressed or implied,
including warranties of merchantability or tness, are limited in duration to the warranty period set forth
above. The consumer’s and/or dealer’s sole remedy shall be such repair or replacement as is expressly

provided above; and under no circumstances shall ADJ Product, LLC be liable for any loss and/or damage,
direct and/or consequential arising out of the use of, and/or inability to use this product.

G. This warranty is the only written warranty applicable to ADJ Products, LLC products, and supersedes all

prior warranties and written descriptions of warranty terms and conditions heretofore published.

MANUFACTURER’S LIMITED WARRANTY PERIODS:

• Non-LED Lighting Products = 1-Year (365 Days) (Including Special Effect Lighting, Intelligent Lighting,
UV lighting, Strobes, Fog Machines, Bubble Machines, Mirror Balls, Par Cans, Trussing, Lighting Stands,

Power/Data Distribution, etc. excluding LED and lamps)

• Laser Products = 1-Year (365 Days) (excluding laser diodes which have a 6-Month Limited Warranty)

• LED Products = 2-Year (730 Days) (excluding batteries which have a 180 Day Limited Warranty)

• NOTE: 2-Year (730 Days) Limited Warranty ONLY applies to product purchased within the United States.

StarTec Series = 1-Year (365 Days) (excluding batteries which have a 180 Day Limited Warranty)

• ADJ DMX Controllers = 2 Year (730 Days)

• American Audio Products = 1 Year (365 Days)

5

WARRANTY REGISTRATION

Please fill out the enclosed warranty card to validate your purchase. All returned service items,
whether under warranty or not, must be freight pre-paid and accompanied by a return authorization
(R.A.) number. The R.A. number must be clearly written on the outside of the return package. A brief
description of the problem as well as the R.A. number must also be written down on a piece of paper
included in the shipping carton. If the unit is under warranty, you must provide a copy of your proof of
purchase invoice. You may obtain an R.A. number by contacting our customer support team. All pack­ages returned to the service department not displaying an R.A. number on the outside of the package
will be returned to the shipper.

FEATURES

• Motorized Focus

• Motorized Zoom: 12° ~ 23°

• 2 Frost Filters (Heavy and Medium)

• 2 Prism FX: Rotating 5-facet Linear & rotating 6-facet Circular

• 0-100% smooth dimming

• Various strobe speeds

• 2 cooling fans

INCLUDED ITEMS

• Omega Bracket (x1)

• Locking Power Cable (x1)

IP RATING

An IP rated lighting fixture is commonly installed in outdoor environments and has been designed with
an enclosure that effectively protects the ingress (entry) of external foreign objects such as dust and
water. The Ingress Protection (IP) rating system is commonly expressed as “IP” followed by two num-

bers (i.e. IP65), where the numbers define the degree of protection. The first digit (Foreign Bodies

Protection) indicates the extent of protection against particles entering the fixture and the second digit
(Water Protection) indicates the extent of protection against water entering the fixture. An IP65 rated

lighting fixture, such as this one, has been designed and tested to protect against the ingress
of dust (6) and low-pressure water jets from any direction (5).

6

SAFETY PRECAUTIONS

PROTECTION CLASS 1 - FIXTURE MUST BE PROPERLY GROUNDED.

THERE ARE NO USER SERVICEABLE PARTS INSIDE THIS UNIT. DO NOT ATTEMPT

ANY REPAIRS YOURSELF, AS DOING SO WILL VOID YOUR MANUFACTURER’S

WARRANTY. DAMAGES RESULTING FROM MODIFICATIONS TO THIS FIXTURE
AND/OR THE DISREGARD OF SAFETY INSTRUCTIONS AND GUIDELINES IN THIS

MANUAL VOID THE MANUFACTURER’S WARRANTY AND ARE NOT SUBJECT TO

ANY WARRANTY CLAIMS AND/OR REPAIRS.

NEVER LOOK DIRECTLY INTO THE LIGHT SOURCE!
RETINA INJURY RISK - MAY INDUCE BLINDNESS!
SENSITIVE PERSONS MAY SUFFER AN EPILEPTIC SHOCK!

• Maximum ambient operating temperature is 113° F (45° C)!

• DO NOT TOUCH the fixture housing during operation. Disconnect the power and allow approxi­mately 15 minutes for the fixture to cool down before servicing.

• DO NOT shake the fixture, and avoid brute force when installing and/or operating the fixture.

• DO NOT operate the fixture if the power cord has become frayed, crimped and/or damaged. If the
power cord is damaged, replace immediately with a new one of the same power rating.

• DO NOT attempt to remove or break off the ground prong from the electrical cord. This prong is
used to reduce the risk of electrical shock and fire in case of an internal short.

• DO NOT attempt to operate this unit if it has been damaged in any way.

• DO NOT spill water or other liquids into or on to your unit.

• Disconnect from main power before making any type of connection.

• DO NOT block any air ventilation slots. All fan and air inlets must remain clean and never blocked.

Allow approx. 6” (15cm) between fixture and other devices or a wall for proper cooling.

• Always be sure to mount this unit in an area that will allow proper ventilation.

• DO NOT remove the cover under for any reason.

• When installing fixture in a suspended enviroment, always use mounting hardware that is no less

than M10 x 25mm, and always install fixture with an appropriately rated safety cable.

• Never plug this unit in to a dimmer pack.

• During long periods of non-use, disconnect the unit’s main power.

• Always mount this unit in safe and stable matter.

• Power-supply cords should be routed so that they are not likely to be walked on or pinched by

items placed upon or against them, paying particular attention to the point where they exit from the

unit.

• Cleaning - The fixture should be cleaned only as recommended by the manufacturer.

• Heat - The appliance should be situated away from heat sources such as radiators, heat registers,
stoves, or other appliances (including amplifiers) that produce heat.

• The fixture should be serviced by qualified service personnel when:
A. The power-supply cord or the plug have been damaged.
B. Objects have fallen onto, or liquid has been spilled into, the fixture.
C. The fixture does not appear to operate normally or exhibits a marked change in performance.
D. The fixture has fallen and/or has been subjected to extreme handling.

7

SAFETY PRECAUTIONS

RISK GROUP 3 - RISK OF EXPOSURE TO ULTRAVIOLET (UV) RADIATION!

FIXTURE EMITS HIGH INTENSITY ULTRAVIOLET (UV) LIGHT FROM THE UV LED.

WEAR PROPER EYE AND SKIN PROTECTION.

AVOID PROLONGED PERIODS OF EXPOSURE TO THE UV LED.

AVOID WEARING WHITE COLOR CLOTHING AND/OR USING (UV) PAINTS ON SKIN.

AVOID DIRECT EYE AND/OR SKIN EXPOSURE AT DISTANCES SHORTER THAN 11 feet (3.3m).

DO NOT OPERATE FIXTURE WITH DAMAGED OR MISSING EXTERNAL COVER.

DO NOT LOOK DIRECTLY INTO THE (UV) LIGHT AND/OR VIEW (UV) LIGHT DIRECTLY WITH
OPTICAL INSTRUMENTS THAT MAY CONCENTRATE THE LIGHT/RADIATION OUTPUT.

INDIVIDUALS SUFFERING FROM A RANGE OF EYE CONDITIONS, SUNLIGHT EXPOSURE DIS­ORDERS, OR INDIVIDUALS USING PHOTOSENSITIVE MEDICATION MAY EXPERIENCE DIS­COMFORT IF EXPOSED TO THE ULTRAVIOLET (UV) LIGHT EMITTED FROM THIS FIXTURE.

8

OVERVIEW

Mode

Button

Display
Screen

Left

Button

Down

Button

Enter

Button

Right

Button

Up

Button

Carry

Handle

Power

In

Safety

Cable

Loop

Power

Out

Fuse

Omega
Bracket
Mounts

DMX

Out

DMX

In

Carry

Handle

9

INSTALLATION

DO NOT INSTALL THE FIXTURE IF YOU ARE NOT QUALIFIED TO DO SO!

Fixture MUST be installed following all local, national, and country commercial electrical and construc­tion codes and regulations.

When installing the unit, the trussing or area of installation must be able to support at least 10 times
the weight of the unit and any attached accessories without any deformation. The unit must be
secured with a secondary safety attachment, e.g. an appropriately-rated safety cable.

Before rigging/mounting a fixture to any metal truss/structure or placing the fixture(s) on any surface, a

professional equipment installer MUST be consulted to determine if the metal truss/structure or surface
is properly certified to safely hold the combined weight of the fixture(s), clamps, cables, and accesso­ries.

Maximum ambient operating temperature is 113°F (45°C).

Fixture(s) should be installed away from walking paths, seating areas, or areas where unauthorized
personnel might reach the fixture by hand.

NEVER stand directly below the fixture(s) when rigging, removing, or servicing.

Overhead fixture installation must always be secured with a secondary safety attachment, such as an
appropriately rated safety cable that can hold at least 10 times the weight of the fixture.

Overhead mounting requires extensive experience, including calculating working load limits, knowl-

edge of installation material being used, and perodic safety inspection of all installation material as
well as the unit itself. If you lack these qualifications, do not attempt the installation yourself.

The installaiton should be checked by a skilled person once a year.

10

INSTALLATION

CLAMP MOUNTING

This fixture features mounting points on the underside for the attachment of two Omega brackets.

Additionally, the unit also features a safety cable loop on the underside, near one of the carry handles

(see the illustration below). When mounting the fixture to a truss or any other suspended or overhead

installation, be sure to secure appropriately rated mounting clamps (not included) to each Omega
bracket. Please note that two Omega brackets and two mounting clamps are needed to safely
support the fixture in a suspended installation. Attach a separate SAFETY CABLE of the appro-
priate weight rating to the provided safety cable loop. NEVER use carry handles as an attachment
points for the safety cable.

MOUNTING

CLAMPS

OMEGA

CLAMP

MOUNTING

POINTS

(2 per clamp)

OMEGA

CLAMPS

SAFETY

CABLE

LOOP

SAFETY CABLE:

ALWAYS ATTACH A SAFETY CABLE WHENEVER INSTALLING THIS FIX-

TURE IN A SUSPENDED ENVIRONMENT TO ENSURE THAT THE FIXTURE

WILL NOT FALL IF THE CLAMP FAILS.

11

INSTALLATION

POTENTIAL INTERNAL FIXTURE DAMAGE FROM EXTERNAL SOURCES OF LIGHT BEAMS

External sources of light beams from direct sunlight, lighting and moving head fixtures, and lasers,
which are focused directly towards the exterior housing and/or penetrate the front lens opening of ADJ
lighting fixtures, can cause severe internal damage including burning of optics, dichroic color filters,

glass and metal gobos, prisms, animation wheels, frost filters, iris, shutters, motors, belts, wiring, dis­charge lamps, and LEDs.

This issue is not specific only to ADJ lighting fixtures, but rather it is a common issue with lighting fix­tures from all manufacturers. Although there is no true way to fully prevent this issue from happening,
the guidelines below can reduce the risk of potential damage. Contact ADJ Service for more details.

DO NOT EXPOSE THE FIXTURE AND/OR FRONT LENS OPENING TO LIGHT BEAMS FROM
DIRECT SUNLIGHT, OTHER LIGHTING OR MOVING HEAD FIXTURES, AND LASERS DURING
UNPACKING, INSTALLATION, USE, AND EXTENDED IDLE TIMES OUTDOORS. DO NOT FOCUS
A LIGHT BEAM FROM ONE LIGHTING FIXTURE DIRECTLY TOWARDS ANOTHER.

SUN PROTECTION MODE/ HIBERNATION MODE:

This state can be set via DMX, or the device will go into this state after 3 minutes without a DMX sig­nal. This function can be switched on or off in the DMX traits (see the DMX Traits section for details).
When the sun protection is activated, the pan-and-tilt function of the moving-head will position the lens
away from direct sunlight, or other high intensity light source, to protect the internal belts, electronics
etc. from burn damage.

When the unit is in the ‘sun protection state’, it uses its accelerometer sensors (X-Y-Z) (only present on

discharge units and IP units) to position the front lens downwards, even when the unit(s) will be moved
from its position. This will keep on changing the position of the head.

Please note that ‘manual mode’ overrides the ‘sun-protection mode’. The hibernation function is

an existing feature that puts the unit into a ‘sleep state’ to save power (this is a state where only the

electronics remain on, and all other functions are turned off, functions such as motors lamps etc). This
state is automatically activated when no DMX signal is present for the set time (1-99min or off).

12

REMOTE DEVICE MANAGEMENT (RDM)

NOTE: In order for RDM to work properly, RDM enabled equipment must be used throughout
the entire system, including DMX data splitters and wireless systems.

Remote Device Management (RDM) is a protocol that sits on top of the DMX512 data standard for

lighting, allowing the DMX systems of the xtures to be modied and monitored remotely. This proto-

col is ideal for instances in which a unit is installed in a location that is not easily accessible.

With RDM, the DMX512 system becomes bi-directional, allowing a compatible RDM enabled con-

troller to send out a signal to devices on the wire, as well as allowing the xture to respond (known as

a GET command). The controller can then use its SET command to modify settings that would typi-

cally have to be changed or viewed directly via the unit’s display screen, including the DMX Address,

DMX Channel Mode, and Temperature Sensors.

FIXTURE RDM INFORMATION:

RDM Code Device ID Device Model ID Personality ID

Basic 17 (1)

0x1900 26 0000-FFFF 26

Standard 20 (2)

Extend 22 (3)

Please be aware that not all RDM devices support all RDM features, and therefore it is important
to check beforehand to ensure that the equipment that you are considering includes all of the fea­tures that you require.

The following parameters are accessible in RDM on this device:

[0x0015] Comms Status [0x00E1] DMX Personality Description
[0x0020] Queued Messages [0x0200] Sensor Denition
[0x0030] Status Message [0x0201] Sensor Value
[0x0031] Status ID Description [0x0400] Device Hours
[0x0032] Clear Status ID [0x0405] Device Power Cycles
[0x0080] Device Model Description [0x0500] Display Invert
[0x0081] Manufacturer Label [0x0501] Display Level
[0x0082] Device Label [0x0600] Pan Invert
[0x0090] Factory Defaults [0x0601] Tilt Invert
[0x00C1] Boot Software Version ID [0x1001] Reset Device
[0x00E0] DMX Personality

13

COLOR WHEELS

COLOR WHEEL 1

CTB

(5600K)

High
CRI

UV

Orange

Red

Medium

Blue

Green

Amber

Magenta

Blue

Green

COLOR WHEEL 2

Yellow

Light

Purple

CTO

(3200K)

UV

Pink

14

GOBOS

DESIGNS

3

4

2

5

1

6

GOBO DIMENSIONS

Thickness Inner (Viewable) Diameter Outer Diameter

0 in

0.002in

(0.5mm)

0.75in

(19.0mm)

0.906in

(23.0mm

-0.008in

0mm

-0.2mm

)

15

GOBOS

ROTATING GOBO HOLDER DIMENSIONS

ø 0.94in (24.0mm)

ø 0.906in
(23.0mm

+0.004 in

-0.0 in

+0.1 mm

-0.0 mm

)

ø 0.83in (21.0mm)

ø 0.906in
(23.0mm

+0.008 in

-0.004 in

+0.2 mm

-0.1 mm

)

(3.0mm)

0.12in

Orientation

Point

(6.2mm)

0.24in

16

ø 0.83in

(21.0mm)

GOBOS

REPLACEMENT PROCEDURE

1. Place the device on a at, stable surface, and allow the device to cool down for at least 1 hour
before beginning this procedure.

2. Engage both the pan and tilt locks, and remove the head covers.

3. Locate the gobo module, which can be identied by nding the cooling fan located near the middle
of the module, as shown in the illustration below. Disconnect any electrical connectors linking the

module to the xture head, and remove the screws holding the module in place. Slide the module

out of the head.

4. Pull the gobo holder away from the gobo wheel, then gently slide it outwards. Use a pair of needle
nose pliers to carefully remove the retainer spring from the gobo holder. The gobo can now be
removed from the gobo holder, and replaced with a new gobo. Reassemble by reversing these
steps.

17

CONTROL PANEL

The Hydro Spot 1 features a display screen with a 6-button control pad, which can be used to easily
adjust any device settings.

• The MODE button cycles through main menu options, or returns to the previous menu without mak-

ing changes.

• The ENTER button is used to select the highlighted option, or to conrm a selection.

• The UP, DOWN, LEFT, and RIGHT buttons are used to navigate and adjust menu options and set-

tings displayed on the screen.

KEY LOCK

This function allows the user to configure whether or not the display screen and control panel keys
will lock after a certain period of inactivity. It can be accessed by navigating to Personality > Display >
Key Lock in the system menu. The setting options are described below:

• OFF: The display screen and control panel keys remain active at all times.

• ON: The display screen and control panel keys automatically lock after a certain period of inactiv-

ity, which can be set under Personality > Display > Screen Saver Delay. To unlock, press and hold
the MODE button for 10 seconds.

• ON1: The display screen and control panel keys automatically lock after a certain period of inac­tivity, which can be set under Personality > Display > Screen Saver Delay. To unlock, press UP,
DOWN, UP, DOWN, ENTER in that order.

18

SYSTEM MENU

DMX Address 001 - xxx

DMX Channel
Mode

DMX SETTINGS

No DMX Status

Prim/Sec Mode Primary / Secondary

Select Signal

Wiy Settings

PERSONALITY

Status Settings

Fan Settings

Zoom Speed

Basic 17

Standard 20

Extended 22

Holds last settings

Hold Last

Blackout

Manual

Internal Programs

DMX or Wiy

Wiy and DMX Out

Wiy Enable On / Off

Set Wiy Channel 00 - 14

Pan Degree 540 / 630

Pan Invert On / Off

Tilt Invert On / Off

P/T Feedback On / Off Pan/Tilt Feedback

P/T Speed

Hibernation Off, 01min - 99 min Default = 15min

Head Fan

Base Fan

Standard

Fast

Speed 1

Speed 2

Auto

High

Low

Auto

High

Low

when DMX signal
is lost

Takes all channels
to 0 when DMX
signal is lost

Reverts to manual
mode when DMX
signal is lost

Reverts to se­lected internal
program when
DMX signal is lost

DMX has prior­ity; green LED

indicates Wiy

connected, and
red LED indicates
Wiy not con­nected

DMX XLR output
sends DMX signal
out

Pan/Tilt Speed

CONTINUED ON NEXT PAGE

19

SYSTEM MENU

Dim Modes

LED Refresh Rate

Dim Curve

Reset Motors

PERSONALITY
(continued)

Display

Service Passcode = 050

Pan 000 - 255

MANUAL
CONTROL

Pan Fine 000 - 255

Tilt 000 - 255

Tilt Fine 000 - 255

... ...

Standard

Stage

TV

Architectural

Theatre

Stage 2

Dim Speed 0.1s - 10.0s

900 Hz-1500 Hz, 2500 Hz, 4000 Hz, 5000 Hz, 6000 Hz, 10
KHz, 15 KHz, 20 KHz, 25 KHz

Square

Linear

Inv Squa

S Curve

Reset All Motors Yes / No

Pan/Tilt Reset Yes / No

... ...

Effect Reset Yes / No

Intensity 1 - 10

Display Invert Yes / No

Screen Saver
Delay

Key Lock

Off - 10 min Default = 05 min

Off Keys do not lock

On

On1

Pan 000 - 255

Tilt 000 - 255

Effect Adjust
(Calibration)

Update Software Off / On

Factory Restore
Passcode = 011

Color1 000 - 255

Color2 000 - 255

Gobo 000 - 255

Shutter 000 - 255

...

Off / On

Default = 1200 Hz

Press and hold
MODE button for
10 sec to unlock
keys

Press Up, Down,
Up, Down, Enter
to unlock keys

CONTINUED ON NEXT PAGE

20

SYSTEM MENU

INTERNAL
PROGRAMS

INFORMATION

Program 1

Program 2

... ... ...

Program 7

Fixture Life Time

Total LED Time

Fixture Temps

Fixture Humidity

Fan Info (RPM)

DMX Values

Error Logs

Software Version U:xxx

Speed 000 - 255

Fade 000 - 255

Speed 000 - 255

Fade 000 - 255

Speed 000 - 255

Fade 000 - 255

Power On Time xxxxxx Hours

P-On Time-R xxxxxx Hours

P-On Time-Reset Passcode = 050

LED On Time xxxxxx Hours

LED On Time-R xxxxxx Hours

LED Hours Reset Passcode = 050

Current xxx F / xxx C

LEDs

Max Resettable xxx F / xxx C

Current xxx F / xxx C

Base Temp

Max Resettable xxx F / xxx C

Reset LED Temp Yes / No Passcode = 050

Reset Base Temp Yes / No Passcode = 050

Head xxx %

Base xxx %

LED Fan xxxx RPM LED

Base Fan xxxx RPM

Pan

Pan Fine

...

xxxxx

Reset Error Log Yes / No Passcode = 050

Total lifetime

hours that xture

has been pow­ered on, cannot
be reset

Hours powered on
since last reset

Reset hours pow­ered on

Total lifetime
hours that LED
has been run,
cannot be reset

Hours LED has
been run since
last reset

Reset LED run
hours

Displays current
LED temp

Max recorded

LED temp since
last reset

Displays current
base temp

Max recorded

base temp since
last reset

List errors one by
one

21

DMX SET UP

DMX-512: DMX is short for Digital Multiplex. This is a universal protocol used as a form of commu-

nication between intelligent fixtures and controllers. A DMX controller sends DMX data instructions
from the controller to the fixture. DMX data is sent as serial data that travels from fixture to fixture via
the DATA “IN” and DATA “OUT” XLR terminals located on all DMX fixtures (most controllers only have
a DATA “OUT” terminal).

DMX Linking: DMX is a language allowing all makes and models of different manufacturers to be

linked together and operate from a single controller, as long as all fixtures and the controller are

DMX compliant. To ensure proper DMX data transmission, try to use the shortest cable path possible

when linking several DMX fixtures. The order in which fixtures are connected in a DMX line does not
influence the DMX addressing. For example, a fixture assigned a DMX address of 1 may be placed
anywhere in a DMX line: at the beginning, at the end, or anywhere in the middle. When a fixture is

assigned a DMX address of 1, the DMX controller knows to send DATA assigned to address 1 to that
unit, no matter where it is located in the DMX chain.

Data Cable (DMX Cable) Requirements (For DMX Operation): This unit can be controlled via DMX­512 protocol. The DMX address is set on the rear panel of the unit. Your unit and your DMX controller
require a standard 5-pin XLR connector for data input and data output. We recommend Accu-Cable
DMX cables. If you are making your own cables, be sure to use standard 110-120 Ohm shielded
cable (This cable may be purchased at almost all pro lighting stores). Your cables should be made
with a male XLR connector at one end and a female XLR connector at the other. Also remember that
DMX cable must be daisy chained and cannot be split.

Notice: Be sure to follow the diagram below when making your own cables. Do not use the ground

lug on the XLR connector. Do not connect the cable’s shield conductor to the ground lug or allow the
shield conductor to come into contact with the XLR’s outer casing. Grounding the shield could cause

a short circuit and erratic behavior.

Special Note: Line Termination. When longer runs of cable are used, you may need to use a termi­nator on the last unit to avoid erratic behavior. A terminator is a 110-120 ohm 1/4 watt resistor which is
connected between pins 2 and 3 of a male XLR connector (DATA + and DATA -). This unit is inserted
in the female XLR connector of the last unit in your daisy chain to terminate the line. Using a cable
terminator (ADJ part number Z-DMX/T) will reduce the risk of erratic behavior.

22

DMX SET UP

DMX ADDRESSING.

All fixtures should be given a DMX starting address when using a DMX controller, so the correct fix­ture responds to the correct control signal. This digital starting address is the channel number from

which the fixture starts to “listen” to the digital control signal sent out from the DMX controller. The

assignment of this starting DMX address is achieved by setting the correct DMX address on the digi-

tal control display on the fixture.

You can set the same starting address for all fixtures or a group of fixtures, or set different addresses
for each individual fixture. Setting all fixtures to the same DMX address will cause all fixtures to react
in the same way. In other words, changing the settings of one channel will affect all the fixtures simul-

taneously.

If you set each fixture to a different DMX address, each unit will start to “listen” to the channel number
you have set, based on the quantity of DMX channels of each fixture. That means changing the set­tings of one channel will only affect the selected fixture.

For example, when this unit is operating in 17 channel mode, you should set the starting DMX

address of the first unit to 1, the second unit to 18 (1 + 17), the third unit to 35 (1 + 17 + 17), and so
on. See the chart below for more details.

CHANNEL MODE UNIT 1 ADDRESS UNIT 2 ADDRESS UNIT 3 ADDRESS UNIT 4 ADDRESS

17 Ch 1 18 35 52
20 Ch 1 21 41 61
22 Ch 1 23 45 67

23

DMX TRAITS

CHANNEL

17 CH 20 CH 22 CH

1 1 1 000 - 255 Pan Movement, 540/630

2 2 000 - 255 Pan Fine

2 3 3 000 - 255 Tilt Movement, 270

4 4 000 - 255 Tilt Fine

3 5 5

4 6 6

DMX

VALUES

000 - 009 Open

010 - 016 Open / Red

017 - 023 Red

024 - 030 Red / Medium Blue

031 - 037 Medium Blue

038 - 044 Medium Blue / Green

045 - 051 Green

052 - 058 Green / Amber

059 - 065 Amber

066 - 072 Amber / Orange

073 - 079 Orange

080 - 086 Orange / High CRI

087 - 093 High CRI

094 - 100 High CRI / CTB (5600K)

101 - 107 CTB (5600K)

108 - 114 CTB (5600K) / UV

115 - 121 UV

122 - 127 UV / Open

128 - 189 Clockwise Color Wheel Rotation, fast to slow

190 - 193 No Rotation

194 - 255 Counter-Clockwise Color Wheel Rotation, slow to fast

000 - 009 Open

010 - 016 Open / Magenta

017 - 023 Magenta

024 - 030 Magenta / Blue

031 - 037 Blue

038 - 044 Blue / Green

045 - 051 Green

052 - 058 Green / Yellow

059 - 065 Yellow

066 - 072 Yellow / Light Purple

073 - 079 Light Purple

080 - 086 Light Purple / Pink

FUNCTION

Color Wheel 1

Color Wheel 2

CONTINUED ON NEXT PAGE

24

DMX TRAITS

CHANNEL

17 CH 20 CH 22 CH

4 6 6

5 7 7

6 8 8

DMX

VALUES

087 - 093 Pink

094 - 100 Pink / UV

101 - 107 UV

108 - 114 UV / CTO (3200K)

115 - 121 CTO (3200K)

122 - 127 CTO (3200K) / Open

128 - 189 Clockwise Color Wheel Rotation, fast to slow

190 - 193 No Rotation

194 - 255 Counter-Clockwise Color Wheel Rotation, slow to fast

000 - 004 Open

005 - 019 Gobo 1 - Dotted Tunnel

020 - 034 Gobo 2 - Scattered Triangles

035 - 049 Gobo 3 - Swipe

050 - 064 Gobo 4 - Flower Petals

065 - 079 Gobo 5 - Starry Night

080 - 094 Gobo 6 - Swirl

095 - 109 Gobo 1 Shake, slow to fast

110 - 124 Gobo 2 Shake, slow to fast

125 - 139 Gobo 3 Shake, slow to fast

140 - 154 Gobo 4 Shake, slow to fast

155 - 169 Gobo 5 Shake, slow to fast

170 - 189 Gobo 6 Shake, slow to fast

190 - 221 Clockwise Gobo Wheel Rotation, fast to slow

222 - 223 No Rotation

224 - 255 Counter-Clockwise Gobo Wheel Rotation, slow to fast

000 - 127 Indexing

128 - 189 Clockwise Gobo Rotation, fast to slow

190 - 193 No Rotation

194 - 255 Counter-Clockwise Gobo Rotation, slow to fast

FUNCTION

Color Wheel 2 (continued)

Gobo Wheel

Gobo Rotation

CONTINUED ON NEXT PAGE

25

DMX TRAITS

CHANNEL

17 CH 20 CH 22 CH

7 9 9

8 10 10 000 - 255 Dimmer Intensity, 0% to 100%

11 000 - 255 Dimmer Intensity Fine

9 11 12

DMX

VALUES

000 - 031 Shutter Closed

032 - 063 Shutter Open

064 - 095 Strobe, slow to fast

096 - 127 Shutter Open

128 - 159 Pulse Effect, slow to fast

160 - 191 Shutter Open

192 - 223 Random Strobe, slow to fast

224 - 255 Shutter Open

000 - 005 No Prism - Open

006 - 066 Prism 1 (5 Facet Linear Prism)

067 - 127 Prism 2 (6 Facet Circular Prism)

129 - 135 Macro 1

136 - 143 Macro 2

144 - 151 Macro 3

152 - 159 Macro 4

160 - 167 Macro 5

168 - 175 Macro 6

176 - 183 Macro 7

184 - 191 Macro 8

192 - 199 Macro 9

200 - 207 Macro 10

208 - 215 Macro 11

216 - 223 Macro 12

224 - 231 Macro 13

232 - 239 Macro 14

240 - 247 Macro 15

248 - 255 Macro 16

000 - 005 Prism Rotation Off

FUNCTION

Shutter

Prisms and Prism/Gobo Macros

Prism Rotation

10 12 13

006 - 128

129 - 191 Clockwise Prism Rotation, fast to slow

192 No Rotation

193 - 255 Counter-Clockwise Prism Rotation, slow to fast

11 13 14 000 - 255 Focus, 0% to 100%
12 14 15 000 - 255 Zoom, narrow to wide

Prism Indexing, 0°...540°

CONTINUED ON NEXT PAGE

26

DMX TRAITS

CHANNEL

17 CH 20 CH 22 CH

16 000 - 255 Zoom Fine
13 15 17 000 - 255 Heavy Frost, 0% to 100%
14 16 18 000 - 255 Medium Frost, 0% to 100%

15 17 19

18 20

16 19 21

17 20 22

DMX

VALUES

000 - 020 Default to Unit Setting

021 - 040 Standard

041 - 060 Stage

061 - 080 TV

081 - 100 Architectural

101 - 120 Theater

121 - 140 Stage 2

141 - 160 Dim Speed, fast to slow (0.1s to 10.0s)

161 - 255 Default to Unit Setting

000 - 020 Square

021 - 040 Linear

041 - 060 Inv Squa

061 - 080 S Curve

081 - 255 No Function

000 - 225 Pan/Tilt, fast to slow

226 - 235 Blackout by Movement

236 - 245 Blackout by All Wheel Changing

246 - 255 No Function

000 - 039 No Function

040 - 049 Fan Control - Low (hold 3s)

050 - 059 Fan Control - High (hold 3s)

060 - 069 Fan Control - Auto (Default, hold 3s)

070 - 074 All motor reset (hold 3s)

075 - 079 Pan/tilt reset (hold 3s)

080 - 084 Color reset (hold 3s)

085 - 089 Gobo reset (hold 3s)

090 - 094 Focus and zoom reset (hold 3s)

095 - 099 Shutter reset (hold 3s)

100 - 104 No Function

105 - 109 Other motors reset (hold 3s)

110 - 148 No Function

FUNCTION

Dimmer Modes

Dim Curves

Pan/Tilt Speed

Special Functions

CONTINUED ON NEXT PAGE

27

DMX TRAITS

CHANNEL

17 CH 20 CH 22 CH

17 20 22

DMX

VALUES

149 - 150 Wiy On (Default, hold 3s)

151 - 152 Wiy Off (hold 5s)
153 - 154 Hibernation Enable (hold 3s) - see Installation section for details
155 - 156 Hibernation Off (hold 5s) - see Installation section for details

157 - 158 Display Backlight On (hold 3s)

159 - 160 Display Backlight Off (hold 5s)

161 - 162 Pan/Tilt Speed 1 (default, hold 5s)

163 - 164 Pan/Tilt Speed 2 (hold 5s)

165 - 166 Invert Pan On (hold 3s)

167 - 168 Invert Pan Off (hold 5s)

169 - 170 Invert Tilt On (hold 3s)

171 - 172 Invert Tilt Off (hold 5s)

173 900

174 910

175 920

176 930

177 940

178 950

179 960

180 970

181 980

182 990

183 1000

184 1010

185 1020

186 1030

187 1040

188 1050

189 1060

190 1070

191 1080

192 1090

193 1100

194 111 0

195 1120

196 1130

197 1140

FUNCTION

Special Functions (continued)

Refresh Rate (Hz, Hold 1s)

CONTINUED ON NEXT PAGE

28

DMX TRAITS

CHANNEL

17 CH 20 CH 22 CH

17 20 22

DMX

VALUES

198 1150

199 1160

200 1170

201 1180

202 1190

203 1210

204 1220

205 1230

206 1240

207 1250

208 1260

209 1270

210 1280

211 1290

212 1300

213 1310

214 1320

215 1330

216 1340

217 1350

218 1360

219 1370

220 1380

221 1390

222 1400

223 1410

224 1420

225 1430

226 1440

227 1450

228 1460

229 1470

230 1480

231 1490

232 1500

233 2500

234 4000

235 5000

FUNCTION

Refresh Rates (Hz, hold 3s) (continued)

CONTINUED ON NEXT PAGE

29

DMX TRAITS

CHANNEL

17 CH 20 CH 22 CH

17 20 22

DMX

VALUES

236 6000

237 10,000

238 15,000

239 20,000

240 25,000

241 Internal Program 1 (scenes 1-8, hold 3s)

242 Internal Program 2 (scenes 9-16, hold 3s)

243 Internal Program 3 (scenes 17-24, hold 3s)

244 Internal Program 4 (scenes 25-32, hold 3s)

245 Internal Program 5 (scenes 33-40, hold 3s)

246 Internal Program 6 (scenes 41-48, hold 3s)

247 Internal Program 7 (scenes 49-56, hold 3s)

248 - 255 No Function

FUNCTION

Refresh Rates (Hz, hold 3s) (continued)

30

DIM SPEEDS

DMX VALUES DELAY TIME

121 0.1 sec
122 0.2 sec
123 0.3 sec
124 0.4 sec
125 0.5 sec
126 0.6 sec
127 0.7 sec
128 0.8 sec
129 0.9 sec
130 1.0 sec
131 1.5 sec
132 2.0 sec
133 3.0 sec
134 4.0 sec
135 5.0 sec
136 6.0 sec
137 7.0 sec
138 8.0 sec
139 9.0 sec
140 10.0 sec

31

DIM MODES

DIMMER

100%

50%

10%

0%

255 255

0 0

Stage 2 0 1100 0 1660

Rise Time

Down Time

0 sec Fade Time

1 sec Fade Time

Time (ms)

0 Sec

Dimming Curve

Ramp Effect

Rise Time (ms) Down Time (ms) Rise Time (ms) Down Time (ms)

Standard (default) 0 0 0 0

Stage 780 1100 1540 1660

TV 1180 1520 1860 1940

Architectural 1380 1730 2040 2120

Theatre 1580 1940 2230 2280

32

PRIMARY-SECONDARY SET UP

This function allows you to link units together to run in a Primary-Secondary set-up, in which one unit

will act as the controlling unit and the others will react to the controlling unit’s built-in programs. Any

unit can be configured to act as a Primary or as a Secondary, but only one unit in a given system can
be programmed to act as the Primary.

Primary-Secondary Connections and Settings:

1. Daisy chain your units via the XLR connectors on the rear panels of each unit. Use standard XLR
data cables to link your units together. Remember that the male XLR connector is the input and
the female XLR connector is the ouput. The first unit in the chain (primary) will use the female XLR
connector only, wile the last unit in the chain will use the male XLR connector only.

2. Use the display screen and control panel to navigate to Personality > Prim/Sec Mode. Select

this sub-menu using the ENTER button, and use the arrows to toggle between “Primary” and
“Secondary”. Press ENTER to confirm your selection.

3. Repeat Step 2 for each unit in the system. Make sure that only one unit is designated as the
Primary, while all other units are designated as Secondaries.

4. The secondary units will now follow the behavior of the primary unit.

MULTI UNIT POWER LINKING

This features allows you to connect the fixtures to one another using the power cable input and output

sockets.

The maximum number of units that can be linked in this manner is as follows:

• 3 units when running on 110V power.

• 8 units when running on 240V power.

DO NOT EXCEED THIS MAXIMUM NUMBER WHEN POWER LINKING UNITS!

All linked units must be of the same make and model type. Do not mix and match units!

33

MAINTENANCE GUIDELINES

DISCONNECT POWER BEFORE PERFORMING ANY MAINTENANCE!

CLEANING

Frequent cleaning is recommended to ensure proper function, optimized light output, and an extend­ed life. The frequency of cleaning depends on the environment in which the fixture operates: damp,
smoky, or particularly dirty environments can cause greater accumulation of dirt on the fixture’s optics.
Clean the external lens surface regularly with a soft cloth to avoid dirt/debris accumulation.

NEVER use alcohol, solvents, or ammonia-based cleaners.

MAINTENANCE

Regular inspections are recommended to ensure proper function and extended life. There are no
user serviceable parts inside this fixture. Please refer all other service issues to an authorized ADJ

service technician. Should you need any spare parts, please order genuine parts from your local ADJ
dealer.

Please refer to the following points during routine inspections:
A. A detailed electrical check by an approved electrical engineer every three months, to make sure

the circuit contacts are in good condition and prevent overheating.

B. Be sure all screws and fasteners are securely tightened at all times. Loose screws may fall out

during normal operation, resulting in damage or injury as larger parts could fall.

C. Check for any deformations on the housing, color lenses, rigging hardware, and rigging points

(ceiling, suspension, trussing). Deformations in the housing could allow for dust to enter into the

fixture. Damaged rigging points or unsecured rigging could cause the fixture to fall and seriously

injure a person(s).

D. Electric power supply cables must not show any damage, material fatigue, or sediments.

NEVER remove the ground prong from the power cable.

SOFTWARE UPDATES

For software updates, please contact ADJ service to obtain a software uploader and detailed instruc­tions. Refer to the Introduction section of this manual for contact information.

FIXTURE DISASSEMBLY

The following points should be observed after performing any maintenance procedure that requires
disassembly of the unit:

• After the unit has been reassembled, open the valve, and allow the light to run for approximately 2

hours in order to dry out any moisture that has been trapped inside the fixture. The process should

continue until indicated humidity drops below 15% for the head and 30% for the base.

• Once this has been achieved, the light can be switched off, but the unit should remain connected
to power so that the cooling fan can cool down the unit. Please note that allowing cool down time
should ALWAYS be done after lamp operation.

• Some units may require partial disassembly in order to gain access to the valve. Please contact
ADJ service for information regarding the location and access procedure for the valve on your
specific unit model.

34

TORQUE SETTINGS FOR SCREWS

ALL SCREWS MUST BE TIGHTENED WITH A TORQUE DRIVER. All screws are Allen head

screws. Please refer to the table and diagram below for screw locations, quantity, and torque settings.

1

2

3

5

Zone

No.

Description Quantity Torque Spec

1 Lens Frame 4

2 Main Head Cover 7 per side (14 total)

3 Arm Cover 6 per side (12 total)

4 Base Side Cover 8 per side (16 total)

5 Carry Handle 2 per handle (4 total)

35

4

4.3 + 0.6 in-lb
(5.0 + 0.7 Kg-cm)

6.9 + 0.6 in-lb
(8.0 + 0.7 Kg-cm)

4.3 + 0.4 in-lb
(5.0 + 0.5 Kg-cm)

6.9 + 0.6 in-lb
(8.0 + 0.7 Kg-cm)

6.9 + 0.6 in-lb
(8.0 + 0.7 Kg-cm)

TORQUE SETTINGS FOR SCREWS

TORQUE DRIVERS (Recommended): UTICA TS-30 (Shown)

TORQUE DRIVER (Alternate):

• Proto J6107A

• Wiha 28887

CAUTION! DO NOT OVER TORQUE SCREWS AS THIS CAN CAUSE LEAKAGE
ISSUES! TO CONFIRM THE IP65 INTEGRITY AFTER A LAMP REPLACEMENT,
TEST THE FIXTURE USING THE IP TESTER. CONTACT ADJ SERVICE FOR
MORE DETAILS.

CAUTION! THE USE OF PROTECTIVE GLOVES AND SAFETY GOGGLES IS
STRONGLY RECOMMENDED WHILE PERFORMING THE IP PRESSURE TEST!
AVOID PLACING YOUR FACE, EYES, HANDS, ETC IN CLOSE PROXIMITY TO

THE FIXTURE’S LENS WHILE PERFORMING THE TEST!

IP PRESSURE TESTING PARAMETERS

Maximum Pressure Minimum Pressure Steady/Hold Time

3.3 psi (23 KPa) 2.9 psi (20 KPa) 15 sec

36

ERROR CODES

When power is applied, the unit will automatically enter a “Reset/Test” mode. This mode brings all
the internal motors to a home position. If there is an internal problem with one or more of the motors,

an error code will ash in the display, as described in the chart below. For example, when the dis­play shows “Pan” it means there is some type of error with the Pan motor. If there are multiple errors
during the start-up process, they will all ash in the display. For example: if the xtures have errors
on Pan, Tilt, and Color Wheel 1 all at the same time, you will see the error message “Pan”, “Tilt”, and
“Color Wheel 1” ash repeated 5 times.

If an error does occur during the initial start-up procedure, the xture will self-generate a second reset

signal and try to realign all the motors and correct the errors. If the error persists after a second at­tempt, a third attempt will be made. If after a third attempt all the errors have not been corrected, the

xture will make the following determinations:

• 3 or More Errors: The xture cannot function properly with three or more errors. Therefore the

xture will place itself in a stand-by mode until subsequent repairs can be made.

• Less Than 3 Errors: The xture has less than 3 errors. Therefore, most other functions will work

properly. The xture will attempt to operate normally until the errors can be correct by a technician.
The errors in question will remain ashing in the display as a reminder of internal errors.

Error Code Description

Pan Pan Error
Tilt Tilt Error
Color Wheel 1 Color Wheel 1 Error
Color Wheel 2 Color Wheel 2 Error
Focus Focus Error
Zoom Zoom Error
Gobo Gobo Wheel Error
Rot Gobo Gobo Rotation Error
Prism 1 Prism 1 Error
Prism 1 Rot Prism 1 Rotation Error
Prism 2 Prism 2 Error
Prism 2 Rot Prism 2 Rotation Error
LED Fan LED Fan Error
Base Fan Base Fan Error
LED Temp LED Temperature Error
Base Temp Base Temperature Error

37

DIMENSIONAL DRAWINGS

Ø 2.97in (75.53mm)

19.22in (488.15mm)

14.94in (379.60mm)

0.36in

4.31in (109.40mm)

(9.22mm)

12.41in (315.17mm)

8.82in

(224.00mm)

7.82in (198.57mm)

11.48in (291.55mm)

10.33in (262.30mm)

13.14in (333.80mm)

8.18in (209.79mm)

9.41in (239.00mm)

8.17in (207.45mm)

9.09in (231.00mm)

14.13in (359.00mm)

6.43in

5.47in
(163.45mm)

(139.00mm)

Drawings are not to scale.

9.41in (239.00mm)

38

SPECIFICATIONS

Light Source:

• 200W Cool White LED Engine (50,000 hr.)

Features:

• Motorized Focus

• Motorized Zoom: 12° ~ 23°

• 2 Frost Filters (Heavy and Medium)

• 2 Prism FX: Rotating 5-facet Linear & rotating
6-facet Circular

• 0-100% smooth dimming

• Various strobe speeds

• 2 cooling fans

Color Wheels:

• (2) Color wheels

• 8 dichroic colors + white on each wheel
(includes CTO, CTB and UV filters)

GOBO Wheels:

• (1) Wheel with 6 Rotatable Gobo’s

• All Gobo’s are replaceable

• Gobo Shake Effect

• Aluminum GOBO size: 23mm (outer); 19mm
(viewable); 0.5mm (thickness)

• Glass gobo size: 23mm (outer); 19mm (view­able); 3.3mm (thickness)

Prism Wheel:

• Prism Wheel 1: Rotatable 6-facet Circular

• Prism Wheel 2: Rotatable 5-facet Linear

• Both Prisms are indexable

Frost Filters:

• Frost 1: Heavy frost for wash effect

• Frost 2: Medium frost creates lightly blurred
edges for Gobo and Prism FX

Control:

• 3 DMX Channel Modes: 17/20/22-ch

• Color LCD display with 6-button function
menu

• Control Mode: DMX512 or internal programs

• 6 Dim Modes: Standard, Stage, TV,
Architectural, Theatre, Stage2

• 4 Dim Curves: Square, Linear, Inv. Square
and S. Curve

• Selectable LED Refresh Rates (900 Hz~25K
Hz)

• 0-100% smooth dimming

• Various strobe speeds

• RDM (Remote Device Management)

• With Wired Digital Communication Network

Pan/Tilt:

• Pan: 630 degrees

• Tilt: 270 degrees

Connections:

• DMX Connections: 5-pin XLR In/Out

• Power Connections: IP65 PowerLock In/Out
to daisy chain power

Electrical:

• Multi-voltage operation: 90-240V, 50/60Hz

• Max power consumption: 280W

Dimensions & Weight:

• Dimensions (LxWxH): 9.49” x 14.57” x

19.21” (241x370x488mm)

• Weight: 35.2lbs (16kg)

Approvals / Rating:

• ETL Approved / CE Certified

• IP65 with Marine Coated Exterior and con­formal coated PCBs

4010765

Please Note: Specifications and improvements in the design of this unit and this manual are subject to change without

any prior written notice.

39