ADJ HYDRO PROFILE User Manual [EN]

HYDRO PROFILE

User Manual

©2022 ADJ Products, LLC all rights reserved. Information, specications, diagrams, images, and

instructions herein are subject to change without notice. ADJ Products, LLC logo and identifying prod­uct names and numbers herein are trademarks of ADJ Products, LLC. Copyright protection claimed
includes all forms and matters of copyrightable materials and information now allowed by statutory or
judicial law or hereinafter granted. Product names used in this document may be trademarks or regis­tered trademarks of their respective companies and are hereby acknowledged. All non-ADJ Products,
LLC brands and product names are trademarks or registered trademarks of their respective compa­nies.

ADJ Products, LLC and all afliated companies hereby disclaim any and all liabilities for property,

equipment, building, and electrical damages, injuries to any persons, and direct or indirect economic
loss associated with the use or reliance of any information contained within this document, and/or as
a result of the improper, unsafe, insufcient and negligent assembly, installation, rigging, and opera­tion of this product.

DOCUMENT VERSION

Due to additional product features and/or enhancements, an updated version of
this document may be available online.
Please check www.adj.com for the latest revision/update of this manual
before beginning installation and/or programming.

Date

Document

Version

05/25/2022 1.0 1.01 36 / 50 / 57 Ch. Initial Release.

07/13/2022 1.1 1.02 No Change

07/19/2022 1.2 N/C No Change

10/19/2022 1.3 1.03 No Change

Software

Version

DMX Channels Notes

Added: Torque Settings for Screws.
Updated: Features, Installation, Gobos,
RDM, Control Panel, System Menu,
Cleaning & Maintenance.

Updated Dimensional Drawings and
Specifications.

Updated gobo page, temporary outdoor
use notice, System Menu, & DMX Traits

Europe Energy Saving Notice
Energy Saving Matters (EuP 2009/125/EC)
Saving electric energy is a key to help protecting the enviroment. Please turn off all electrical products when
they are not in use. To avoid power consumption in idle mode, disconnect all electrical equipment from power
when not in use. Thank you!

2

TABLE OF CONTENTS

Introduction 4
Limited Warranty (USA Only) 5
Warranty Registration | Features 6
Safety Guidelines 7
Overview 8
Installation 9
Remote Device Management (RDM) 12
Gobos 13
Control Panel 16
System Menu 17
DMX Setup 20
DMX Traits 22
Color Wheel | Animation Wheel 30
White Color Temperature Chart 31
Frame Macros Chart 32
Dim Speeds 33
Dimmer Modes 34
Cleaning and Maintenance 35
Torque Settings for Screws 37
Dimensional Drawings 39
Error Codes 40
Specifications 41

3

INTRODUCTION

Unpacking: Thank you for purchasing the Hydro Prole by ADJ Products, LLC. Every device has been

thoroughly tested and has been shipped in perfect operating condition. Carefully check the shipping
carton for damage that may have occurred during shipping. If the carton appears to have been dam-

aged, carefully inspect your xture for any damage and be sure all accessories necessary to operate

the unit have arrived intact. In the event that damage has been found or parts are missing, please con­tact our toll free customer support number for further instructions. Do not return this unit to your dealer

without rst contacting customer support.

Introduction: The ADJ Hydro Prole is a DMX intelligent, weather-proof LED moving head xture. To

optimize the performance of this product, please read these operating instructions carefully in order to
familiarize yourself with the basic operations of this unit. These instructions contain important safety
information regarding the use and maintenance of this unit. Please keep this manual with the unit for
future reference.

Customer Support: Contact ADJ Service for any product related service and support needs. Also visit

forums.adj.com with questions, comments or suggestions.

Parts: To purchase parts online visit:

http://parts.adj.com (US)
http://www.adjparts.eu (EU)

ADJ SERVICE USA - Monday - Friday 8:00am to 4:30pm PST
Voice: 800-322-6337 | Fax: [phone] | [e-mail]

ADJ SERVICE EUROPE - Monday - Friday 08:30 to 17:00 CET
Voice: [phone] | Fax: [phone] | [e-mail]

ADJ PRODUCTS LLC USA

6122 S. Eastern Ave. Los Angeles, CA. 90040

323-582-2650 | Fax [phone] | www.adj.com | [e-mail]

ADJ SUPPLY Europe B.V

Junostraat 2 6468 EW Kerkrade, The Netherlands

[phone] | Fax [phone]

www.americandj.eu | [e-mail]

ADJ PRODUCTS GROUP Mexico

AV Santa Ana 30 Parque Industrial Lerma, Lerma, Mexico 52000

[phone]

CAUTION! There are no user serviceable parts inside this unit. Do not attempt any repairs yourself,

as doing so will void your manufacturer’s warranty. In the unlikely event your unit may require service,

please contact ADJ Products, LLC.

Do not discard the shipping cartoon in the trash. Please recycle when ever possible.

4

LIMITED WARRANTY (USA ONLY)

A. ADJ Products, LLC hereby warrants, to the original purchaser, ADJ Products, LLC products to be free of

manufacturing defects in material and workmanship for a prescribed period from the date of purchase (see

specic warranty period on reverse). This warranty shall be valid only if the product is purchased within the
United States of America, including possessions and territories. It is the owner’s responsibility to establish

the date and place of purchase by acceptable evidence, at the time service is sought.

B. For warranty service, you must obtain a Return Authorization number (RA#) before sending the product

back—please contact ADJ Products, LLC Service Department at 800-322-6337. Send the product only to
the ADJ Products, LLC factory. All shipping charges must be prepaid. If the requested repairs or service
(including parts replacement) are within the terms of this warranty, ADJ Products, LLC will pay return ship­ping charges only to a designated point within the United States. If the entire instrument is sent, it must be
shipped in its original package and packaging material. No accessories should be shipped with the product.
If any accessories are shipped with the product, ADJ Products, LLC shall incur no liability whatsoever for
loss of or damage to any such accessories, nor for the safe return thereof.

C. This warranty is void if the product serial number and/or labels are altered or removed; if the product is

modied in any manner which ADJ Products, LLC concludes, after inspection, affects the reliability of the

product; if the product has been repaired or serviced by anyone other than the ADJ Products, LLC factory
unless prior written authorization was issued to purchaser by ADJ Products, LLC; if the product is dam­aged because it was not properly maintained as set forth in the product instructions, guidelines and/or user
manual.

D. This is not a service contract, and this warranty does not include maintenance, cleaning, or periodic check-

up. During the period specied above, ADJ Products, LLC will replace defective parts at its expense with
new or refurbished parts, and will absorb all expenses for warranty service and repair labor by reason of

defects in material or workmanship. The sole responsibility of ADJ Products, LLC under this warranty shall
be limited to the repair of the product, or replacement thereof, including parts, at the sole discretion of ADJ
Products, LLC. All products covered by this warranty were manufactured after August 15, 2012, and bear
identifying marks to that effect.

E. ADJ Products, LLC reserves the right to make changes in design and/or improvements upon its products

without any obligation to include these changes in any products theretofore manufactured.

F. No warranty, whether expressed or implied, is given or made with respect to any accessory supplied with

products described above. Except to the extent prohibited by applicable law, all implied warranties made by
ADJ Products, LLC in connection with this product, including warranties of merchantability or tness, are
limited in duration to the warranty period set forth above. And all warranties, whether expressed or implied,
including warranties of merchantability or tness, are limited in duration to the warranty period set forth
above. The consumer’s and/or dealer’s sole remedy shall be such repair or replacement as is expressly

provided above; and under no circumstances shall ADJ Product, LLC be liable for any loss and/or damage,
direct and/or consequential arising out of the use of, and/or inability to use this product.

G. This warranty is the only written warranty applicable to ADJ Products, LLC products, and supersedes all

prior warranties and written descriptions of warranty terms and conditions heretofore published.

MANUFACTURER’S LIMITED WARRANTY PERIODS:

• Non-LED Lighting Products = 1-Year (365 Days) (Including Special Effect Lighting, Intelligent Lighting,
UV lighting, Strobes, Fog Machines, Bubble Machines, Mirror Balls, Par Cans, Trussing, Lighting Stands,

Power/Data Distribution, etc. excluding LED and lamps)

• Laser Products = 1-Year (365 Days) (excluding laser diodes which have a 6-Month Limited Warranty)

• LED Products = 2-Year (730 Days) (excluding batteries which have a 180 Day Limited Warranty)

• NOTE: 2-Year (730 Days) Limited Warranty ONLY applies to product purchased within the United States.

StarTec Series = 1-Year (365 Days) (excluding batteries which have a 180 Day Limited Warranty)

• ADJ DMX Controllers = 2 Year (730 Days)

• American Audio Products = 1 Year (365 Days)

5

WARRANTY RETURNS

Please ll out the enclosed warranty card to validate your purchase. All returned service items,

whether under warranty or not, must be freight pre-paid and accompanied by a return authorization
(R.A.) number. The R.A. number must be clearly written on the outside of the return package. A brief
description of the problem as well as the R.A. number must also be written down on a piece of paper
included in the shipping carton. If the unit is under warranty, you must provide a copy of your proof of
purchase invoice. You may obtain an R.A. number by contacting our customer support team on our
customer support number. All packages returned to the service department not displaying an R.A.
number on the outside of the package will be returned to the shipper.

FEATURES

The Hydro Profile is ADJ’s first weatherproof moving head profile fixture, which combines a potent 660­Watt cool white LED light engine with an impressive 25,000+ Lumens, and an expansive feature set to

deliver a truly powerful and versatile luminaire.

INCLUDED ITEMS

• Omega Bracket (x2)

• Locking Power Cable (x1)

IP RATING

An IP rated lighting fixture is commonly installed in outdoor environments and has been designed
with an enclosure that effectively protects the ingress (entry) of external foreign objects such as dust
and water. The Ingress Protection (IP) rating system is commonly expressed as “IP” followed by two

numbers (i.e. IP65), where the numbers define the degree of protection. The first digit (Foreign Bodies

Protection) indicates the extent of protection against particles entering the fixture, while the second
digit (Water Protection) indicates the extent of protection against water entering the fixture.

An IP65 rated lighting fixture, such as this one, is dust tight, and protected against low pres­sure water jets from any direction. INTENDED FOR TEMPORARY OUTDOOR USE ONLY!

6

SAFETY GUIDELINES

THIS FIXTURE IS COMPOSED OF SOPHISTICATED ELECTRONIC COMPONENTS. TO GUARANTEE
SMOOTH OPERATION, IT IS IMPORTANT TO FOLLOW ALL INSTRUCTIONS AND GUIDELINES IN
THIS MANUAL. ADJ PRODUCTS, LLC IS NOT RESPONSIBLE FOR INJURY AND/OR DAMAGES
RESULTING FROM THE MISUSE OF THIS FIXTURE DUE TO THE DISREGARD OF THE INFORMATION
PRINTED IN THIS MANUAL. ONLY QUALIFIED AND/OR CERTIFIED PERSONNEL SHOULD PERFORM
INSTALLATION OF THIS FIXTURE AND ONLY THE ORIGINAL RIGGING PARTS INCLUDED WITH THIS
FIXTURE SHOULD BE USED FOR INSTALLATION. ANY MODIFICATIONS TO THE FIXTURE AND/OR

THE INCLUDED MOUNTING HARDWARE WILL VOID THE ORIGINAL MANUFACTURER’S WARRANTY

AND INCREASE THE RISK OF DAMAGE AND/OR PERSONAL INJURY. ONLY CERTIFIED PERSONNEL
SHOULD PERFORM INSTALLATION OF THIS FIXTURE.

• PROTECTION CLASS 1 - FIXTURE MUST BE PROPERLY GROUNDED.

• THERE ARE NO USER SERVICEABLE PARTS INSIDE THIS UNIT.

• DO NOT ATTEMPT ANY REPAIRS YOURSELF; DOING SO WILL VOID YOUR MANUFACTURER’S
WARRANTY. DAMAGES RESULTING FROM MODIFICATIONS TO THIS FIXTURE AND/OR THE
DISREGARD OF SAFETY INSTRUCTIONS AND GUIDELINES IN THIS MANUAL VOID THE

MANUFACTURER’S WARRANTY AND ARE NOT SUBJECT TO ANY WARRANTY CLAIMS AND/OR

REPAIRS.

• DO NOT PLUG FIXTURE INTO A DIMMER PACK!

• NEVER OPEN THIS FIXTURE WHILE IN USE!

• UNPLUG POWER BEFORE SERVICING FIXTURE!

• NEVER TOUCH FIXTURE DURING OPERATION, AS IT MAY BE HOT!

• KEEP FLAMMABLE MATERIALS AWAY FROM FIXTURE!

• NEVER LOOK DIRECTLY INTO THE LIGHT SOURCE!

• RETINA INJURY RISK - MAY INDUCE BLINDNESS!

• SENSITIVE PERSONS MAY SUFFER AN EPILEPTIC SHOCK!

• MINIMUM DISTANCE TO OBJECTS/SURFACES IS 6.6 FEET (2 METERS)

• MAXIMUM AMBIENT TEMPERATURE IS 113° F (45°C). DO NOT OPERATE THE DEVICE WHEN
AMBIENT TEMPERATURE EXCEEDS THIS VALUE.

• MINIMUM DISTANCE TO FLAMMABLE MATERIALS FROM THE SURFACE IS 1.6 FEET (0.5 METER).

• DO NOT TOUCH the xture housing during operation. Turn OFF the power and allow approximately 60
minutes for the xture to cool down before servicing.

• DO NOT shake xture, and avoid brute force when installing and/or operating xture.

• DO NOT operate xture if the power cord is frayed, crimped, damaged and/or if any of the power cord con-

nectors are damaged and do not insert into the xture securely with ease. NEVER force a power cord con­nector into the xture. If the power cord or any of its connectors are damaged, replace it immediately with a

new one of the same power rating.

• DO NOT block any air ventilation slots. All fan and air inlets must remain clean and never blocked. Allow

approx. 6” (15cm) between xture and other devices or a wall for proper cooling.

• When installing xture in a suspended environment, always use mounting hardware that is no less than
M10 x 25 mm, and always install xture with an appropriately rated safety cable.

• Always disconnect xture from main power source before performing any type of service and/or cleaning
procedure.

• Only handle the power cord by the plug end. Never pull out the plug by tugging the wire portion of the cord.

• During the initial operation of this xture, a light smoke or smell may emit from the interior of the xture.

This is a normal process and is caused by excess paint in the interior of the casing burning off from the

heat associated with the lamp and will decrease gradually over time.

• Consistent operational breaks will ensure xture will function properly for many years.

• ONLY use original packaging and materials to transport the xture for service.

7

OVERVIEW

Pan

Lock

Carry

Handle

Mode

Button

Out

DMX

In

Carry

Handle

Safety

Cable

Loop

Display
Screen

Left

Button

Down

Button

Enter

Button

Right

Button

FusePower

In

DMX

Up

Button

Omega
Bracket

Attachment

Points

8

INSTALLATION

FLAMMABLE MATERIAL WARNING

Keep xture minimum 5.0 feet (1.5m) away from flammable materials and/or pyrotechnics.

ELECTRICAL CONNECTIONS

A qualied electrician should be used for all electrical connections and/or installations.

MINIMUM DISTANCE TO OBJECTS/SURFACES IS 6.6 FEET (2 METERS).
MINIMUM DISTANCE OF FLAMMABLE MATERIALS FROM THE SURFACE IS 1.6
FEET (0.5 METER)

DO NOT INSTALL THE FIXTURE IF YOU ARE NOT QUALIFIED TO DO SO!

• FixtureMUSTbeinstalledfollowingalllocal,national,andcountrycommercialelectricalandcon­structioncodesandregulations.

• Beforerigging/mountingasinglefixtureormultiplefixturestoanymetaltruss/structureorplacing
thefixture(s)onanysurface,aprofessionalequipmentinstallerMUSTbeconsultedtodetermine
whetherthemetaltruss/structureorsurfaceisproperlycertifiedtosafelyholdthecombined
weightofthefixture(s),clamps,cables,andaccessories.

• Maximumfixtureambientoperatingtemperatureis113°F (45°C). Donotuseoperatethefixture
whenambienttemperatureexceedsthisvalue!

• Fixture(s)shouldbeinstalledoutsidewalkingpaths,seatingareas,orareaswereunauthorized
personnelmightreachthefixturebyhand.

• NEVERstanddirectlybelowthefixture(s)whenrigging,removing,orservicing.

• Overheadfixtureinstallationmustalwaysbesecuredwithasecondarysafetyattachment,such
asanappropriatelyratedsafetycable.

• Allowapproximately60minutesforthefixturetocooldownbeforeservicing.

IP RATING

An IP rated lighting fixture is commonly installed in outdoor environments and has been designed
withanenclosurethateffectivelyprotectstheingress(entry)ofexternalforeignobjectssuchasdust
andwater.TheIngressProtection(IP)ratingsystemiscommonlyexpressedas“IP”followedbytwo
numbers(i.e.IP65),wherethenumbersdefinethedegreeofprotection.Thefirstdigit(ForeignBodies
Protection)indicatesthe extent ofprotectionagainst particlesentering the fixture,whilethe second
digit(WaterProtection)indicatestheextentofprotectionagainstwaterenteringthefixture.

An IP65 rated lighting fixture, such as this one, is dust tight, and protected against low pressure
water jets from any direction. INTENDED FOR TEMPORARY OUTDOOR USE ONLY!

RIGGING
Overhead rigging requires extensive experience, including calculating working load limits,
knowledge about installation materials being used, and periodic safety inspection of all instal-

lation material and the fixture, among other skills. If you lack these qualifications, do not

attempt the installation yourself. Improper installation can result in bodily injury.

9

INSTALLATION

CLAMP INSTALLATION

This fixture features a mounting points on the underside of the base for the attachment of Omega

clamps. Make sure to always install the device using both Omega clamp mounting points. A loop
for the attachment of a safety cable is also located on the underside of the base (see the illustration

below). When mounting the fixture to a truss or any other suspended or overhead installation, be sure

to secure an appropriately rated clamp (not included) to each Omega bracket, and attach a separate
SAFETY CABLE of the appropriate weight rating to the safety cable loop.

OMEGA

CLAMP

MOUNTING

POINTS

SAFETY

CABLE

LOOP

SAFETY CABLE:

ALWAYS ATTACH A SAFETY CABLE WHENEVER INSTALLING THIS FIXTURE

IN A SUSPENDED ENVIRONMENT TO ENSURE THAT THE FIXTURE WILL NOT

FALL IF THE CLAMP FAILS.

10

INSTALLATION

POTENTIAL INTERNAL FIXTURE DAMAGE FROM EXTERNAL SOURCES OF LIGHT BEAMS

External sources of light beams from direct sunlight, lighting moving head fixtures, and lasers which
are focused directly towards the exterior housing and/or penetrate the front lens opening of ADJ light­ing fixtures can cause severe internal damage, including burning of optics, dichroic color filters, glass

and metal gobos, prisms, animation wheels, frost filters, irises, shutters, motors, belts, wiring, dis­charge lamps, and LEDs.

This issue is not unique to ADJ lighting fixtures, but rather it is a common issue with lighting fixtures

from all manufacturers. Although there is no true way to completely prevent this issue from hap­pening, the guidelines below can reduce the risk of any potential damage if followed. Contact ADJ
Service for more details.

DO NOT EXPOSE THE FIXTURE AND/OR FRONT LENS OPENING TO LIGHT BEAMS FROM
DIRECT SUNLIGHT, OTHER LIGHTING OR MOVING HEAD FIXTURES, AND LASERS DURING
UNPACKING, INSTALLATION, USE, AND EXTENDED IDLE TIMES OUTDOORS. DO NOT FOCUS
A LIGHT BEAM FROM ONE LIGHTING FIXTURE DIRECTLY TOWARDS ANOTHER.

SUN PROTECTION MODE/ HIBERNATION MODE:

This state can be set via DMX, or the device will go into this state after 3 minutes without a DMX sig­nal. This function can be switched on or off in the DMX traits (see the DMX Traits section for details).
When the sun protection is activated, the pan-and-tilt function of the moving-head will position the lens
away from direct sunlight, or other high intensity light source, to protect the internal belts, electronics
etc. from burn damage.

When the unit is in the ‘sun protection state’, it uses its accelerometer sensors (X-Y-Z) (only present on

discharge units and IP units) to position the front lens downwards, even when the unit(s) will be moved
from its position. This will keep on changing the position of the head.

Please note that ‘manual mode’ overrides the ‘sun-protection mode’. The hibernation function is

an existing feature that puts the unit into a ‘sleep state’ to save power (this is a state where only the

electronics remain on, and all other functions are turned off, functions such as motors lamps etc). This
state is automatically activated when no DMX signal is present for the set time (1-99min or off).

11

REMOTE DEVICE MANAGEMENT (RDM)

NOTE: In order for RDM to work properly, RDM enabled equipment must be used throughout
the entire system, including DMX data splitters and wireless systems.

Remote Device Management (RDM) is a protocol that sits on top of the DMX512 data standard for
lighting, allowing the DMX systems of the fixtures to be modified and monitored remotely. This proto­col is ideal for instances in which a unit is installed in a location that is not easily accessible.

With RDM, the DMX512 system becomes bi-directional, allowing a compatible RDM enabled control-

ler to send out a signal to devices on the wire, as well as allowing the fixture to respond (known as a

GET command). The controller can then use its SET command to modify settings that would typically

have to be changed or viewed directly via the unit’s display screen, including the DMX Address, DMX

Channel Mode, and Temperature Sensors.

FIXTURE RDM INFORMATION:

RDM Code Device ID Device Model ID Personality ID

Basic 36 (1)

0x1900 24 0000-FFFF 24

Standard 50 (2)

Extended 57 (3)

Please be aware that not all RDM devices support all RDM features, and therefore it is important
to check beforehand to ensure that the equipment that you are considering includes all of the features
that you require.

The following parameters are accessible in RDM on this device:

[0x0015] Comms Status [0x00E1] DMX Personality Description
[0x0020] Queued Message [0x0200] Sensor Denition
[0x0030] Status Messages [0x0201] Sensor Value
[0x0031] Status ID Description [0x0400] Device Hours
[0x0032] Clear Status ID [0x0405] Device Power Cycles
[0x0080] Device Model Description [0x0500] Display Invert
[0x0081] Manufacturer Label [0x0501] Display Level
[0x0082] Device Label [0x0600] Pan Invert
[0x0090] Factory Defaults [0x0601] Tilt Invert
[0x00C1] Boot Software Version ID [0x1001] Reset Device
[0x00E0] DMX Personality

12

GOBOS

DESIGNS

FIXED GOBOS ROTATING GOBOS

#2

#3

#4

#5

#6

#7

DIMENSIONS - FIXED GOBOS

#1

#2

#1

#3

#4

#8

#5

#7

#6

ø 0.8in (20.0mm)

1.5in (38.1mm)

13

ø 0.9in

(23.0mm)

(3.2mm)

0.125in

GOBOS

DIMENSIONS - ROTATING GOBOS

Ø 0.08in (2.0mm)

Depth = 0.01in (0.3mm)

Ø 1.4in

(36.0mm)

Note: Dotting and milling

slot on the same tooth tip.

1.8in (46.6mm)

CRITICAL

+0.003in

Ø 0.787in

(20.0mm

Ø 0.906in

(23.0mm

+0.07mm

+0.10mm

-0.02mm

-0.001in

-0.03mm

+0.004in

-0.0008in

)

)

CRITICAL

Ø 0.08in (2.0mm)

Depth = 0.2in (5.6mm)

14

GOBOS

GOBO REPLACEMENT

1. Placethedeviceonaat,stablesurface,andallowthedevicetocooldownforatleast1hour
beforebeginningthisprocedure.

2. Engageboththepanandtiltlocks,andremovetheheadcovers.

3. Locatethegobomodule(secondmodulefromthebottom,asshownintheillustrationbelow).
Disconnectanyelectricalconnectorslinkingthemoduletothefixturehead,andremovethe
screwsholdingthemoduleinplace.Slidethemoduleoutofthehead.

4. Pullthegoboholderawayfromthegobowheel,thengentlyslideitoutwards.Useapairof
needlenoseplierstocarefullyremovetheretainerspringfromthegoboholder.Thegobocan
nowberemovedfromthegoboholder,andreplacedwithanewgobo.Reassemblebyreversing
thesesteps.

15

CONTROL PANEL

The xture includes an easy to navigate system menu control panel display where all necessary set­tings and adjustments are made. (See image below)

• MODE: Cycles through the main menu options and/or return to previous menu without making

changes.

• ENTER: Select highlighted option and/or confirm selection.

• DOWN/UP/LEFT/RIGHT: Use as a directional pad, or to scroll through menu options.

KEY LOCK

This function allows the user to configure whether or not the display screen and control panel keys
will lock after a certain period of inactivity. It can be accessed by navigating to Personality > Display >
Key Lock in the system menu. The setting options are described below:

• OFF: The display screen and control panel keys remain active at all times.

• ON: The display screen and control panel keys automatically lock after a certain period of inactiv-

ity, which can be set under Personality > Display > Screen Saver Delay. To unlock, press and hold
the MODE button for 10 seconds.

• ON1: The display screen and control panel keys automatically lock after a certain period of inac-

tivity, which can be set under Personality > Display > Screen Saver Delay. To unlock, press UP,
DOWN, UP, DOWN, ENTER in that order.

BATTERY

This unit features a dedicated battery that can be used to power the screen display. This allows the

user to configure the device’s channel mode, DMX address, or any other screen-accessible features

without needing to power on the device or even connect it to a power source. To activate the display
on battery power, press and hold the MODE button for 3 seconds. Please note that the battery is

NOT user-accessible, and the user should NOT attempt to access or replace the battery, as

doing so may void your manufacturer’s warranty. If battery replacement is required, please

contact ADJ service for assistance.

16

SYSTEM MENU

DMX Address 001 - xxx

DMX Channel
Mode

DMX Settings

No DMX Status

Prim/Sec Mode Primary / Secondary

Select Signal

Wifly Settings

Status Settings

Fan Settings

Zoom Speed Standard / Fast

Dim Modes

Personality

LED Refresh Rate

Dim Curve

Reset Motors

Display

Service Passcode

Basic 36

Standard 50

Extended 57

Hold Last

Blackout
Manual
Internal Programs

DMX or Wifly DMX has priority

DMX XLR output

Wifly and DMX Out

Wifly Enable On / Off
Set Wifly Channel 00 - 14

Pan Degree 540
Pan Invert On / Off
Tilt Invert On / Off
P/T Feedback On / Off
P/T Speed Speed 1 / Speed 2
Hibernation Off, 01m - 99m Default = 15m

Auto

Head Fan

Base Fan

Standard

Stage
TV
Architectural
Theatre
Stage 2
Dim Speed 0.1s - 10s

900-1500 Hz (1200 Hz), 2500 Hz, 4000 Hz, 5000 Hz, 6000
Hz, 10 KHz, 15 KHz, 20 KHz, 25 KHz

Square

Linear
Inv. Squa.
S. Curve
Reset All Motors Yes / No
Pan/Tilt Reset Yes / No

... ...

Effect Reset Yes / No
Intensity 1-10
Display Invert YES / NO
Screen Saver Delay
Key Lock OFF/ON/ON1

High
Low

Auto

High
Low

OFF-10M 05M

Pan 000 - 255
Tilt 000 - 255

Effect Adjust
(Calibration)
Passcode = 050

Factory Restore Off / On Passcode =- 011

Cyan 000 - 255
Magenta 000 - 255
Yellow 000 - 255
CTO 000 - 255
...

shall send signal
out

17

SYSTEM MENU

Pan 000-255
Pan Fine 000-255

Manual Control

Internal Programs

Information

Tilt 000-255
Tilt Fine 000-255
... 000-255

Program 1

Program 2

...

Program 7

Fixture Life Time

Total LED Time

Fixture Temps

Fixture Humidity

Fan Info (RPM)

DMX Values

Error Logs

Software Version

Speed 000-255
Fade 000-255
Speed 000-255
Fade 000-255

Speed 000-255
Fade 000-255

Total time xture

Power On Time xxxxxx Hours

P-On Time-R xxxxxx Hours

P-On Time-Reset Passcode = 050

LED On Time xxxxxx Hours

LED On Time-R xxxxxx Hours

LED Hours Reset Passcode = 050 Reset LED time

LEDs

Base Temp

Reset LED Temp Yes / No Passcode = 050
Reset Base Temp Yes / No Passcode = 050
Head xxx%
Base xxx%
LED Fan xxxx RPM LED
Base Fan xxxx RPM
Pan
Pan Fine
...

xxxxx
xxxxx

Reset Error Log Yes / No Passcode = 050
1U:XXX
2U:XXX
3U:XXX

Current xxx F / xxx C

Max Resettable xxx F / xxx C
Current xxx F / xxx C
Max Resettable xxx F / xxx C

List Errors one by one

has been powered
during its lifetime

Time xture has

been powered on
since last reset

Reset power on
time

Total time LED
has been powered

on during xture

lifetime
Time LED has

been powered on
since last reset

18

DMX SETUP

DMX-512: DMX is short for Digital Multiplex. This is a universal protocol used as a form of communi-

cation between intelligent fixtures and controllers. A DMX controller sends DMX data instructions from
the controller to the fixture. DMX data is sent as serial data that travels from fixture to fixture via the
DATA “IN” and DATA “OUT” XLR terminals located on all DMX fixtures (most controllers only have a
DATA “OUT” terminal).

DMX Linking: DMX is a language allowing all makes and models of different manufacturers to be

linked together and operate from a single controller, as long as all xtures and the controller are

DMX compliant. To ensure proper DMX data transmission, try to use the shortest cable path possible

when linking several DMX fixtures. The order in which fixtures are connected in a DMX line does not
influence the DMX addressing. For example, a fixture assigned a DMX address of 1 may be placed
anywhere in a DMX line: at the beginning, at the end, or anywhere in the middle. When a fixture is

assigned a DMX address of 1, the DMX controller knows to send DATA assigned to address 1 to that
unit, no matter where it is located in the DMX chain.

Data Cable (DMX Cable) Requirements (For DMX Operation):This device can be controlled via
DMX-512 protocol, and features multiple DMX channel modes. Your unit and your DMX controller
require a 3-pin or 5-pin XLR connector for data input and data output. If you are making your own
cables, be sure to use standard 110-120 Ohm shielded cable (This cable may be purchased at almost
all professional lighting stores). Your cables should be made with a male XLR connector at one end
and a female XLR connector at the other. Also remember that DMX cable must be daisy chained and
cannot be split.

Special Note: Line Termination. When longer runs of cable are used, you may need to use a termi­nator on the last unit to avoid erratic behavior. A terminator is a 110-120 ohm 1/4 watt resistor which is
connected between pins 2 and 3 of a male XLR connector (DATA + and DATA -). This unit is inserted
in the female XLR connector of the last unit in your daisy chain to terminate the line. Using a cable

terminator (ADJ part number Z-DMX/T) will decrease the chances of erratic behavior.

19

DMX SETUP

DMX ADDRESSING

All fixtures should be given a DMX starting address when operating with a DMX controller, in order
to ensure that the correct fixture responds to the correct control signal. This digital starting address is
the channel number from which the fixture starts to “listen” to the digital control signal sent out from

the DMX controller. The starting DMX address is configured by setting the correct DMX address on

the control panel display on the fixture.

You can set the same starting address for multiple fixtures, or set different addresses for each indi­vidual fixture. Setting multiple fixtures to the same DMX address will cause all those fixtures to react

in the same way. In this case, please note that changing the settings of one channel will affect all the

fixtures simultaneously.

If you set each fixture to a different DMX address, each unit will start to “listen” to the channel number
you have set, based on the quantity of DMX channels of each fixture. That means changing the set­tings of one channel will only affect the selected fixture.

As an example, when operating this device in 36 channel mode, you should set the starting DMX

address of the first unit to 1, the second unit to 37 (1 + 36), the third unit to 73 (1 + 36 + 36), and so
on. (See the chart below for more details.)

Channel Mode Unit 1 Address Unit 2 Address Unit 3 Address Unit 4 Address

36 Channels 1 37 73 109
50 Channels 1 51 101 151
57 Channels 1 58 115 172

20

DMX TRAITS

CHANNEL

36 CH 50 CH 57 CH

1 1 1 000 - 255 Pan Pan Movement (540/630)

2 2 000 - 255 Pan Fine Pan Fine

2 3 3 000 - 255 Tilt Tilt Movement (270)

4 4 000 - 255 Tilt Fine Tilt Fine

3 5 5 000 - 255 Cyan 0% to 100%

4 6 7 000 - 255 Magenta 0% to 100%

5 7 9 000 - 255 Yellow 0% to 100%

6 8 11 000 - 255 CTO 0% to 100%

7 9 13

8 10 14

8 10 14

DMX VALUE FUNCTION

6 000 - 255 Cyan Fine 0% to 100%

8 000 - 255 Magenta Fine 0% to 100%

10 000 - 255 Yello Fine 0% to 100%

12 000 - 255 CTO Fine 0% to 100%

White Color Temperature Presets

000 - 023 Open
024 - 076 White Color Temperature Presets, see White Color Temperature Chart
077 - 255 7500K

Color Wheel (Snap)

000 - 004 Open
005 - 017 Open / Red
018 - 030 Red
031 - 043 Red / Medium Blue
044 - 056 Medium Blue
057 - 069 Medium Blue / Green
070 - 082 Green
083 - 095 Green / Amber
096 - 108 Amber
109 - 121 Amber / Orange
122 - 134 Orange
135 - 147 Orange / High CRI Filter
148 - 160 High CRI Filter
161 - 173 High CRI Filter / CTB
174 - 186 CTB
187 - 199 CTB / Open
200 - 226 Clockwise Color Wheel Rotation, Fast -> Slow
227 - 228 No Rotation
229 - 255 Counter Clockwise Color Wheel Rotation, Slow -> Fast

Color Wheel (Index)

000 - 000 Open
001 - 029 Open> Red
030 - 030 Red
031 - 055 Red > Medium Blue
056 - 056 Medium Blue
057 - 078 Medium Blue >Green
079 - 079 Green
080 - 105 Green >Amber
106 - 106 Amber
107 - 127 Amber >Orange
128 - 128 Orange
129 - 152 Orange>High CRI Filter
153 - 153 High CRI Filter
154 - 173 High CRI Filter >CTB
174 - 174 CTB
175 - 198 CTB >Open
199 - 199 Open
200 - 226 Clockwise Color Wheel Rotation, Fast -> Slow
227 - 228 No Rotation
229 - 255 Counter Clockwise Color Wheel Rotation, Slow -> Fast

21

DMX TRAITS

CHANNEL

36 CH 50 CH 57 CH

11 15

9 12 16

DMX VALUE FUNCTION

000 - 031 Off
032 - 039 Macro1
040 - 047 Macro2
048 - 055 Macro3
056 - 063 Macro4
064 - 071 Macro5
072 - 079 Macro6
080 - 087 Macro7
088 - 095 Macro8
096 - 103 Macro9

104 - 111 Macro10

112 - 119 Macro11
120 - 127 Macro12
128 - 135 Macro13
136 - 143 Macro14
144 - 151 Macro15
152 - 159 Macro16
160 - 167 Macro17
168 - 175 Macro18
176 - 183 Macro19
184 - 191 Macro20
192 - 199 Macro21
200 - 207 Macro22
208 - 215 Macro23
216 - 223 Macro24
224 - 231 Macro25
232 - 239 Macro26
240 - 247 Macro27
248 - 255 Random CMY

000 - 009 Open
010 - 019 Gobo 1
020 - 029 Gobo 2
030 - 039 Gobo 3
040 - 049 Gobo 4
050 - 059 Gobo 5
060 - 069 Gobo 6
070 - 079 Gobo 7
080 - 094 Gobo 1 Shake, slow to fast
095 - 109 Gobo 2 Shake, slow to fast
110 - 124 Gobo 3 Shake, slow to fast
125 - 139 Gobo 4 Shake, slow to fast
140 - 154 Gobo 5 Shake, slow to fast
155 - 169 Gobo 6 Shake, slow to fast
170 - 189 Gobo 7 Shake, slow to fast
190 - 221 Clockwise Gobo Wheel Rotation, fast to slow
222 - 223 No Rotation
224 - 255 Counter-Clockwise Gobo Wheel Rotation, slow to fast

Color Macros - CMY and Color Wheel

Gobo Wheel 1

22

DMX TRAITS

CHANNEL

36 CH 50 CH 57 CH

10 13 17

11 14 19

12 15 20

13 16 21 000 - 255 Dimmer Intensity, 0% to 100%

17 22 000 - 255 Dimmer Intensity Fine

DMX VALUE FUNCTION

Gobo 1 Rotation

000 - 005 Gobo 1 Rotation Off

006 - 128

129 - 191 Clockwise Gobo Rotation, fast to slow

192 No Rotation

193 - 255 Counter-Clockwise Gobo Rotation, slow to fast

18 000 - 255 Gobo 1 Rotation Fine

000 - 005 Open

006 - 014 Gobo 1

015 - 023 Gobo 2

024 - 032 Gobo 3

033 - 041 Gobo 4

042 - 050 Gobo 5

051 - 059 Gobo 6

060 - 068 Gobo 7

069 - 077 Gobo 8

078 - 091 Gobo 1 Shake, slow to fast

092 - 105 Gobo 2 Shake, slow to fast

106 - 119 Gobo 3 Shake, slow to fast

120 - 133 Gobo 4 Shake, slow to fast

134 - 147 Gobo 5 Shake, slow to fast

148 - 161 Gobo 6 Shake, slow to fast

162 - 175 Gobo 7 Shake, slow to fast

176 - 189 Gobo 8 Shake, slow to fast

190 - 221 Clockwise Gobo Wheel Rotation, fast to slow

222 - 223 No Rotation

224 - 255 Counter-Clockwise Gobo Wheel Rotation, slow to fast

000 - 031 Shutter Closed

032 - 063 Shutter Open

064 - 095 Strobe, slow to fast

096 - 127 Shutter Open

128 - 159 Pulse Effect, slow to fast

160 - 191 Shutter Open

192 - 223 Random Strobe, slow to fast

224 - 255 Shutter Open

Gobo Index, 0°...540°

Gobo Wheel 2

Shutter

23

DMX TRAITS

CHANNEL

36 CH 50 CH 57 CH

14 18 23

15 19 24

16 20 25 000 - 255 Focus, 0% to 100%

17 21 27 000 - 255 Zoom, narrow to wide

18 22 29

19 23 30 000 - 255 Medium Frost, 0% to 100%
20 24 31 000 - 255 Heavy Frost, 0% to 100%

21 25 32

DMX VALUE FUNCTION

Prisms and Prism/Gobo Macros

000 - 005 No Prism (Open)
006 - 066 Prism 1 (6 Linear Prism)
067 - 127 Prism 2 (4 Facet Prism)
128 - 135 Macro1
136 - 143 Macro2
144 - 151 Macro3
152 - 159 Macro4
160 - 167 Macro5
168 - 175 Macro6
176 - 183 Macro7
184 - 191 Macro8
192 - 199 Macro9
200 - 207 Macro10
208 - 215 Macro11
216 - 223 Macro12
224 - 231 Macro13
232 - 239 Macro14
240 - 247 Macro15
248 - 255 Macro16

Prism Rotation

000 - 005 Prism Rotation Off

006 - 128

129 - 191 Clockwise Prism Rotation, fast to slow

192 No Rotation

193 - 255 Counter-Clockwise Prism Rotation, slow to fast

26 000 - 255 Focus Fine, 0% to 100%

28 000 - 255 Zoom Fine, narrow to wide

000 - 225 Open to Close
226 - 235 Pulse Up, slow to fast
236 - 245 Pulse Down, slow to fast

246 - 255 Random Effect, slow to fast

000 - 005 Animation Rot. OFF
006 - 128 Animation Index 0 ... 540°
129 - 191 Clockwise Animation Rotation, Fast -> Slow

192 No Rotation

193 - 255 Counter Clockwise Animation Rotation, Slow-> Fast

Prism Indexing, 0°...540°

Iris

Animation

24

DMX TRAITS

CHANNEL

36 CH 50 CH 57 CH

22 26 33 000 - 255 Blade 1A, 0% to 100%

27 34 000 - 255 Blade 1A Fine, 0% to 100%

23 28 35 000 - 255 Blade 1B, 0% to 100%

29 36 000 - 255 Blade 1B Fine, 0% to 100%

24 30 37 000 - 255 Blade 2A, 0% to 100%

31 38 000 - 255 Blade 2A Fine, 0% to 100%

25 32 39 000 - 255 Blade 2B, 0% to 100%

33 40 000 - 255 Blade 2B Fine, 0% to 100%

26 34 41 000 - 255 Blade 3A, 0% to 100%

35 42 000 - 255 Blade 3A Fine, 0% to 100%

27 36 43 000 - 255 Blade 3B, 0% to 100%

37 44 000 - 255 Blade 3B Fine, 0% to 100%

28 38 45 000 - 255 Blade 4A, 0% to 100%

39 46 000 - 255 Blade 4A Fine, 0% to 100%

29 40 47 000 - 255 Blade 4B, 0% to 100%

41 48 000 - 255 Blade 4B Fine, 0% to 100%

30 42 49 000 - 255 Frame Rotation, 0° to 120°

43 50 000 - 255 Frame Rotation Fine, 0% to 100%

31 44 51 000 - 255 Frame Speed, max to min

32 45 52

DMX VALUE FUNCTION

Frame Macros, refer to Frame Macros Chart section of this manual

000 - 007 Off
008 - 015 Macro 1
016 - 023 Macro 2
024 - 031 Macro 3
032 - 039 Macro 4
040 - 047 Macro 5
048 - 055 Macro 6
056 - 063 Macro 7
064 - 071 Macro 8
072 - 079 Macro 9
080 - 087 Macro 10
088 - 095 Macro 11
096 - 103 Macro 12

104 - 111 Macro 13

112 - 119 Macro 14
120 - 127 Macro 15
128 - 135 Macro 16
136 - 143 Macro 17
144 - 151 Macro 18
152 - 159 Macro 19
160 - 167 Macro 20
168 - 175 Macro 21
176 - 183 Macro 22
184 - 191 Macro 23
192 - 199 Macro 24
200 - 207 Macro 25
208 - 215 Macro 26
216 - 223 Macro 27
224 - 231 Macro 28
232 - 239 Macro 29
240 - 247 Macro 30
248 - 255 Macro 31

25

DMX TRAITS

CHANNEL

36 CH 50 CH 57 CH

33 46 53

47 54

34 48 55 000 - 255 CMY / Color Macro Speed Max -> Min

35 49 56

36 50 57

DMX VALUE FUNCTION

Dimmer Mode

000 - 020 Default to Unit Setting
021 - 040 Standard
041 - 060 Stage
061 - 080 TV
081 - 100 Architectural
101 - 120 Theater
121 - 140 Stage 2
141 - 160 Dim Speed, fast to slow (0.1s to 10s)
161 - 255 Default to Unit Setting

Dim Curves

000 - 020 Square
021 - 040 Linear
041 - 060 Inv. Squa.
061 - 080 S. Curve
081 - 255 No Function

Pan/Tilt Speed

000 - 225 Pan/Tilt Fast -> Slow
226 - 235 Blackout by movement
236 - 245 Blackout by all wheel changing
246 - 255 No function

Special Functions

000 - 039 No function (1200 Hz LED Refresh Rate (Default)
040 - 049 Fan Control - Low (Hold 3s)
050 - 059 Fan Control - High (Hold 3s)
060 - 069 Fan Control - Auto (Default) (Hold 3s)
070 - 074 All motor Reset (Hold 3s)
075 - 079 Pan / Tilt Reset (Hold 3s)
080 - 084 Color Reset (Hold 3s)
085 - 089 Gobo Reset (Hold 3s)
090 - 094 Focus and Zoom Reset (Hold 3s)
095 - 099 Shutter Reset (Hold 3s)
100 - 104 Framing Reset (Hold 3s)
105 - 109 Other motors Reset (Hold 3s)

110 - 114 Enable Zoom Speed Fast (Hold 3s)

115 - 119 Disable Zoom Speed Fast (Hold 5s)
120 - 124 Pump ON
125 - 129 Pump OFF
130 - 134 Enable Color Wheel Index to any position (Hold 3s)
135 - 139 Disable Color Wheel Index to any position (Hold 5s)
140 - 148 No function
149 - 150 Wifly ON (Default) (Hold 3s)
151 - 152 Wifly OFF (Hold 5s)
153 - 154 Hibernation Enable (Hold 3s)
155 - 156 Hibernation OFF (Hold 5s)
157 - 158 Display Backlight ON (Hold 3s)
159 - 160 Display Backlight OFF (Hold 5s)
161 - 162 Pan/Tilt Speed 1 (Default) (Hold 5s)
163 - 164 Pan/Tilt Speed 2 (Hold 5s)
165 - 166 Invert Pan ON (Hold 3s)
167 - 168 Invert Pan OFF (Hold 5s)
169 - 170 Invert Tilt ON (Hold 3s)
171 - 172 Invert Tilt OFF (Hold 5s)

26

DMX TRAITS

CHANNEL

36 CH 50 CH 57 CH

DMX VALUE FUNCTION

Refresh Rate (Hold 1s)

173 900 Hz LED Refresh Rate (Hold 1s)
174 910 Hz LED Refresh Rate (Hold 1s)
175 920 Hz LED Refresh Rate (Hold 1s)
176 930 Hz LED Refresh Rate (Hold 1s)
177 940 Hz LED Refresh Rate (Hold 1s)
178 950 Hz LED Refresh Rate (Hold 1s)
179 960 Hz LED Refresh Rate (Hold 1s)
180 970 Hz LED Refresh Rate (Hold 1s)
181 980 Hz LED Refresh Rate (Hold 1s)
182 990 Hz LED Refresh Rate (Hold 1s)
183 1000 Hz LED Refresh Rate (Hold 1s)
184 1010 Hz LED Refresh Rate (Hold 1s)
185 1020 Hz LED Refresh Rate (Hold 1s)
186 1030 Hz LED Refresh Rate (Hold 1s)
187 1040 Hz LED Refresh Rate (Hold 1s)
188 1050 Hz LED Refresh Rate (Hold 1s)
189 1060 Hz LED Refresh Rate (Hold 1s)
190 1070 Hz LED Refresh Rate (Hold 1s)
191 1080 Hz LED Refresh Rate (Hold 1s)
192 1090 Hz LED Refresh Rate (Hold 1s)
193 1100 Hz LED Refresh Rate (Hold 1s)
194 1110 Hz LED Refresh Rate (Hold 1s)
195 1120 Hz LED Refresh Rate (Hold 1s)
196 1130 Hz LED Refresh Rate (Hold 1s)
197 1140 Hz LED Refresh Rate (Hold 1s)
198 1150 Hz LED Refresh Rate (Hold 1s)
199 1160 Hz LED Refresh Rate (Hold 1s)
200 1170 Hz LED Refresh Rate (Hold 1s)
201 1180 Hz LED Refresh Rate (Hold 1s)
202 1190 Hz LED Refresh Rate (Hold 1s)
203 1210 Hz LED Refresh Rate (Hold 1s)
204 1220 Hz LED Refresh Rate (Hold 1s)
205 1230 Hz LED Refresh Rate (Hold 1s)
206 1240 Hz LED Refresh Rate (Hold 1s)
207 1250 Hz LED Refresh Rate (Hold 1s)
208 1260 Hz LED Refresh Rate (Hold 1s)
209 1270 Hz LED Refresh Rate (Hold 1s)
210 1280 Hz LED Refresh Rate (Hold 1s)
211 1290 Hz LED Refresh Rate (Hold 1s)
212 1300 Hz LED Refresh Rate (Hold 1s)
213 1310 Hz LED Refresh Rate (Hold 1s)
214 1320 Hz LED Refresh Rate (Hold 1s)
215 1330 Hz LED Refresh Rate (Hold 1s)

27

DMX TRAITS

CHANNEL

36 CH 50 CH 57 CH

36 50 57

DMX VALUE FUNCTION

Refresh Rate (Hold 1s)

216 1340 Hz LED Refresh Rate (Hold 1s)
217 1350 Hz LED Refresh Rate (Hold 1s)
218 1360 Hz LED Refresh Rate (Hold 1s)
219 1370 Hz LED Refresh Rate (Hold 1s)
220 1380 Hz LED Refresh Rate (Hold 1s)
221 1390 Hz LED Refresh Rate (Hold 1s)
222 1400 Hz LED Refresh Rate (Hold 1s)
223 1410 Hz LED Refresh Rate (Hold 1s)
224 1420 Hz LED Refresh Rate (Hold 1s)
225 1430 Hz LED Refresh Rate (Hold 1s)
226 1440 Hz LED Refresh Rate (Hold 1s)
227 1450 Hz LED Refresh Rate (Hold 1s)
228 1460 Hz LED Refresh Rate (Hold 1s)
229 1470 Hz LED Refresh Rate (Hold 1s)
230 1480 Hz LED Refresh Rate (Hold 1s)
231 1490 Hz LED Refresh Rate (Hold 1s)
232 1500 Hz LED Refresh Rate (Hold 1s)
233 2500 Hz LED Refresh Rate (Hold 1s)
234 4000 Hz LED Refresh Rate (Hold 1s)
235 5000 Hz LED Refresh Rate (Hold 1s)
236 6000 Hz LED Refresh Rate (Hold 1s)
237 10,000 Hz LED Refresh Rate (Hold 1s)
238 15,000 Hz LED Refresh Rate (Hold 1s)
239 20,000 Hz LED Refresh Rate (Hold 1s)
240 25,000 Hz LED Refresh Rate (Hold 1s)
241 Internal program 1 (scenes 1~8) (Hold 3s)
242 Internal program 2 (scenes 9~16) (Hold 3s)
243 Internal program 3 (scenes 17~24) (Hold 3s)

244 Internal program 4 (scenes 25~32) (Hold 3s)
245 Internal program 5 (scenes 33~40) (Hold 3s)
246 Internal program 6 (scenes 41~48) (Hold 3s)
247 Internal program 7 (scenes 49~56) (Hold 3s)

248 - 255 No function

28

COLOR WHEEL

BLUE

RED

CTC

ANIMATION WHEEL

GREEN

AMBER

ORANGE

CRI

29

WHITE COLOR TEMPERATURE CHART

DMX VALUES

024 2700
025 2800
026 2900
027 3000
028 3100
029 3200
030 3300
031 3400
032 3500
033 3600
034 3700
035 3800
036 3900
037 4000
038 4100
039 4200
040 4300
041 4400
042 4500
043 4600
044 4700
045 4800
046 4900
047 5000
048 5100
049 5200
050 5300

COLOR

TEMPERATURE

DMX VALUES

051 5400
052 5500
053 5600
054 5700
055 5800
056 5900
057 6000
058 6100
059 6200
060 6300
061 6400
062 6500
063 6600
064 6700
065 6800
066 6900
067 7000
068 7100
069 7200
070 7300
071 7400
072 7500
073 7600
074 7700
075 7800
076 7900

COLOR

TEMPERATURE

30

FRAME MACROS CHART

MACRO

NUMBER

1 150 0 150 0 150 0 150 0

2 138 116 126 0 162 206 88 146

3 146 0 208 70 166 0 162 168

4 220 0 122 0 166 0 114 64

5 0 104 0 124 0 162 64 132

6 88 74 132 240 84 144 11 4 60

7 144 74 0 255 10 108 48 116

8 138 116 198 0 162 106 112 78

9 96 100 0 130 162 0 0 172

10 138 216 134 0 0 206 88 146

11 88 94 0 244 46 112 11 4 44

12 138 216 140 0 0 206 0 0

13 124 62 216 0 108 206 126 2

14 152 118 128 106 136 102 68 114

15 124 54 0 154 16 118 126 206

16 0 214 2 146 0 124 0 128

17 144 74 0 152 10 240 138 74

18 102 120 56 202 30 102 152 40

19 174 104 100 124 194 152 64 132

20 88 74 132 240 84 102 114 172

21 86 11 2 168 0 228 26 122 64

22 146 0 208 70 166 0 162 0

23 138 116 126 0 162 206 11 2 78

24 150 154 150 0 150 0 150 86

25 122 0 0 196 150 0 150 86

26 182 0 98 124 162 64 0 168

27 210 0 120 0 166 0 162 0

28 88 92 150 0 228 144 114 0

29 122 0 0 130 162 0 220 86

30 124 54 216 154 16 11 8 126 2

31 138 116 198 142 0 160 138 80

FRAME

BLADE 1A

FRAME

BLADE 1B

FRAME

BLADE 2A

FRAME

BLADE 2B

FRAME

BLADE 3A

FRAME

BLADE 3B

FRAME

BLADE 4A

FRAME

BLADE 4B

31

DIM SPEEDS

DMX VALUE DELAY TIME

141 0.1s

142 0.2s

143 0.3s

144 0.4s

145 0.5s

146 0.6s

147 0.7s

148 0.8s

149 0.9s

150 1.0s

151 1.5s

152 2.0s

153 3.0s

154 4.0s

155 5.0s

156 6.0s

157 7.0s

158 8.0s

159 9.0s

160 10.0s

32

DIMMER MODES

DIMMER

100%

50%

10%

0%

255 255

0 0

Stage 2 0 1100 0 1660

Rise Time

Down Time

0 sec Fade Time

1 sec Fade Time

Dimming

Curve

Ramp Effect

Time (ms)

0 Sec

Rise Time (ms) Down Time (ms) Rise Time (ms) Down Time (ms)

Standard (default) 0 0 0 0

Stage 780 1100 1540 1660

TV 1180 1520 1860 1940

Architectural 1380 1730 2040 2120

Theatre 1580 1940 2230 2280

33

CLEANING AND MAINTENANCE

DISCONNECT POWER BEFORE PERFORMING ANY MAINTENANCE!

CLEANING

Frequent cleaning is recommended to ensure proper function, optimized light output, and an

extended life. The frequency of cleaning depends on the environment in which the xture operates:
damp, smoky, or particularly dirty environments can cause greater accumulation of dirt on the xture’s
optics. Clean the external lens surface periodically with a soft cloth to avoid dirt/debris accumulation.

NEVER use alcohol, solvents, or ammonia-based cleaners.

MAINTENANCE

Regular inspections are recommended to ensure proper function and extended life. There are no user
serviceable parts inside this xture. Please refer all other service issues to an authorized ADJ service

technician. Should you need any spare parts, please order genuine parts from your local ADJ dealer.

Please refer to the following points during routine inspections:

• A detailed electrical check by an approved electrical engineer every three months, to make sure
the circuit contacts are in good condition and prevent overheating.

• Be sure all screws and fasteners are securely tightened at all times. Loose screws may fall out
during normal operation, resulting in damage or injury as larger parts could fall.

• Check for any deformations on the housing, color lenses, rigging hardware, and rigging points
(ceiling, suspension, trussing). Deformations in the housing could allow for dust or liquids to enter
into the xture. Damaged rigging points or unsecured rigging could cause xture to fall and seri­ously injure a person(s).

• Electric power supply cables must not show any damage, material fatigue, or sediments.

NEVER remove the ground prong from the power cable.

FIXTURE DISASSEMBLY

The following points should be observed after performing any maintenance procedure that requires
disassembly of the unit:

• After the unit has been reassembled, open the valve, and allow the light to run for approximately 2

hours in order to dry out any moisture that has been trapped inside the fixture. The process should
continue until indicated humidity drops below 15% for the head and 30% for the base.

• Once this has been achieved, the light can be switched off, but the unit should remain connected
to power so that the cooling fan can cool down the unit. Please note that allowing cool down time
should ALWAYS be done after lamp operation.

• Some units may require partial disassembly in order to gain access to the valve. Please contact
ADJ service for information regarding the location and access procedure for the valve on your
specific unit model.

34

CLEANING AND MAINTENANCE

PUMP FUNCTION

Certain mechanisms within this fixture, such as the effects wheels and the framing mechanism, emit

small amounts of oil vapor, which can accumulate on the lens and result in reduced light output. To

counteract this issue, this fixture features an air pump installed in the arm, which serves to ventilate
the air inside the fixture head in order to remove this oil vapor. In particular, it is recommended to run

this pump following maintenance or repair procedures of mechanisms inside the head, as these proce­dures can result in increased emission of oil vapor. Refer to the System Menu section of this manual
for instructions on how to activate this pump.

SOFTWARE UPDATES

For software updates, please contact ADJ service to obtain a software uploader and detailed instruc­tions. Refer to the Introduction section of this manual for contact information.

35

TORQUE SETTINGS FOR SCREWS

ALL SCREWS MUST BE TIGHTENED WITH A TORQUE DRIVER. All screws are Allen head

screws. Please refer to the table and diagram below for screw locations, quantity, and torque settings.

1

2

5

Zone

No.

Description Quantity Torque Spec

1 Lens Frame 4

2 Main Head Covers 10 per side (20 total)

3 Arm Covers 6 per side (12 total)

Base Front/Rear

4

Covers

5 Carry Handles 2 per handle (4 total)

8 per side (16 total)

3

4

4.3 + 0.6 lbf-in
(5.0 + 0.7 kgf-cm)

6.9 + 0.6 lbf-in
(8.0 + 0.7 kgf-cm)

4.3 + 0.4 lbf-in
(5.0 + 0.5 kgf-cm)

6.9 + 0.6 lbf-in
(8.0 + 0.7 kgf-cm)

6.9 + 0.6 lbf-in
(8.0 + 0.7 kgf-cm)

36

TORQUE SETTINGS FOR SCREWS

TORQUE DRIVERS (Recommended): UTICA TS-30 (Shown)

TORQUE DRIVER (Alternate):

• Proto J6107A

• Wiha 28887

CAUTION! DO NOT OVER TORQUE SCREWS AS THIS CAN CAUSE LEAKAGE
ISSUES! TO CONFIRM THE IP65 INTEGRITY AFTER A LAMP REPLACEMENT,
TEST THE FIXTURE USING THE IP TESTER. CONTACT ADJ SERVICE FOR
MORE DETAILS.

CAUTION! THE USE OF PROTECTIVE GLOVES AND SAFETY GOGGLES IS
STRONGLY RECOMMENDED WHILE PERFORMING THE IP PRESSURE TEST!
AVOID PLACING YOUR FACE, EYES, HANDS, ETC IN CLOSE PROXIMITY TO

THE FIXTURE’S LENS WHILE PERFORMING THE TEST!

IP PRESSURE TESTING PARAMETERS

Maximum Pressure Minimum Pressure Steady/Hold Time

3.3 psi

(23 KPa)

2.9 psi

(20 KPa)

37

15 sec

DIMENSIONAL DRAWINGS

[4.6in]

116mm

522mm [20.6in]

120mm

[4.7in]

319mm [12.5in]

376mm [14.8in]

573mm [22.6in]

428mm [16.9in]

304mm [12.0in]

260mm [10.2in]

720mm [28.3in]

433mm [17.0in]

180mm

[7.1in]

Dimensions may not be drawn to scale

[7.1in]

180mm

38

ERROR CODES

Pan Prism1
Tilt Prism1 Rot
Cyan Prism2
Magenta Prism2 Rot
Yellow Animation
CTO Animation Rot
Color Wheel Blade Rot
Gobo LED Fan
Rot Robo Base Fan
Fixed Gobo Gobo Fan
Focus LED Temp
Zoom Base Temp

39

SPECIFICATIONS

Light Source:

• 660W Cool White LED Engine (50,000 hr.)

• 25,000+ Lumens

Features:

• Motorized Focus

• 2 Frost Filters

• Motorized Zoom: 6 ~ 45 degrees

• 4 Blade Framing System (Rotatable)

• Iris

• Animation Wheel

• 2 Prism FX: Rotating 6-facet Linear & rotating 4-facet
Circular

• 0-100% smooth dimming

• Various strobe speeds

• 2 cooling fans

Color:

• CMY color mixing system

• Variable CTO flag

• Color wheel with 7 dichroic colors + white (includes CTB
and High CRI filters)

• Colors on wheel are removable and replaceable

Gobo Wheels:

• (1) Rotating Gobo wheel with 7 Gobos

• (1) Static Gobo wheel with 8 Gobos

• All Gobo’s are replaceable

• Gobo Shake Effect on both wheels

• Aluminum Gobo size: 23mm (outer); 19mm (viewable);

0.5mm (thickness)

• Glass gobo size: 23mm (outer); 19mm (viewable);

3.3mm (thickness)

Prism Wheel:

• Prism Wheel 1: Rotatable 6-facet Linear

• Prism Wheel 2: Rotatable 4-facet Circular

• Both Prisms are indexable

Control:

• 3 DMX Channel Modes: 36/50/57

• Color LCD display with 6-button function menu

• Control Mode: DMX512 or internal programs

• 6 Dim Modes: Standard, Stage, TV, Architectural, Theatre,
Stage2

• 4 Dim Curves: Square, Linear, Inv. Square and S. Curve

• Selectable LED Refresh Rates (900 Hz~25K Hz)

• 0-100% smooth dimming

• Various strobe speeds

• With Wired Digital Communication Network

• RDM (Remote Device Management)

Pan/Tilt:

• Pan: 540 degrees

• Tilt: 270 degrees

Connections:

• DMX Connections: 5-pin XLR In/Out

• Power Connections: IP65 PowerLock Input

Electrical:

• Multi-voltage operation: 100-240V, 50/60Hz

• Max power consumption: 1088W

Dimensions & Weight:

• Dimensions (LxWxH): 12.5” x 17.0” x 28.3”
(319x433x720mm)

• Weight: 84.9 lbs (38.5 kg)

Approvals / Rating:

• ETL Approved / CE Certified

• IP65 with Marine Coated Exterior and conformal coated
PCBs (Temporary outdoor use only)

Specifications and manual are subject to improvement

without prior written notice.

Frost Filters:

• Frost 1: Heavy frost for wash effect

• Frost 2: Medium frost creates lightly blurred edges for
Gobo and Prism FX

40