ADJ Hydro Beam X2 User guide

HYDRO BEAM X2

User Instructions

©2019 ADJ Products, LLC all rights reserved. Information, specications, diagrams, images, and

FCC STATEMENT
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.

FCC RADIO FREQUENCY INTERFERENCE WARNINGS & INSTRUCTIONS
This product has been tested and found to comply with the limits as per Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful interference in a residential installation.
This device uses and can radiate radio frequency energy and, if not installed and used in accordance with
the included instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this device does cause harmful
interference to radio or television reception, which can be determined by turning the device off and on, the
user is encouraged to try to correct the interference by one or more of the following methods:

· Reorient or relocate the device.

· Increase the separation between the device and the receiver.

· Connect the device to an electrical outlet on a circuit different from which the radio receiver is
connected.

· Consult the dealer or an experienced radio/TV technician for help.

instructions herein are subject to change without notice. ADJ Products, LLC logo and identifying
product names and numbers herein are trademarks of ADJ Products, LLC. Copyright protection
claimed includes all forms and matters of copyrightable materials and information now allowed by
statutory or judicial law or hereinafter granted. Product names used in this document may be
trademarks or registered trademarks of their respective companies and are hereby acknowledged.
All non-ADJ Products, LLC brands and product names are trademarks or registered trademarks of

their respective companies.

ADJ Products, LLC and all aliated companies hereby disclaim any and all liabilities for property,
equipment, building, and electrical damages, injuries to any persons, and direct or indirect economic
loss associated with the use or reliance of any information contained within this document, and/or as
a result of the improper, unsafe, unsucient and negligent assembly, installation, rigging, and operation
of this product.

DOCUMENT VERSION

Due to additional product features and/or enhancements, an updated version of this document
may be available online.
Please check www.adj.com for the latest revision/update of this manual before beginning
installation and/or programming.

Date

10/30/19

12/17/19

Europe Energy Saving Notice
Energy Saving Matters (EuP 2009/125/EC)

Saving electric energy is a key to help protecting the enviroment. Please turn o all electrical products when
they are not in use. To avoid power consumption in idle mode, disconnect all electrical equipment from power
when not in use. Thank you!

Document
Version

1 1.5

1.2

Software
Version >

1.7

DMX Channel
Mode

15 / 17 Initial Version

N/C Updated Display Lock/Unlock Feature

Notes

Hydro Beam X2 Table of Contents

Introduction
Features I Warranty Registration
IP65 Notice
Safety Guidelines
Overview
Discharge Lamp Warning
Lamp Installation
Gobo Specications I Gobos
Gobo Installation
Fixture Installation

Connections

3
4
5

6

10
11
13
17
18
22
25

DMX Set Up
DMX Addressing
DMX Channel Modes

System Menu

WiFly Control
Error Codes
Dimensional Drawings
Power Linking I Cleaning
Limited Warranty (USA Only)
Technical Specications

26

27
28
31
38
40
42
43
44
45

ADJ Products, LLC - www.adj.com - Hydro Beam X2 User Manual Page 2

Hydro Beam X2 Introduction

Unpacking: Thank you for purchasing the Hydro Beam X2 by ADJ Products, LLC. Every Hydro Beam
X2 has been thoroughly tested and has been shipped in perfect operating condition. Carefully check
the shipping carton for damage that may have occurred during shipping. If the carton appears to be
damaged, carefully inspect your xture for any damage and be sure all accessories necessary to operate
the unit has arrived intact. In the case damage has been found or parts are missing, please contact our
toll free customer support number for further instructions. Do not return this unit to your dealer without
rst contacting customer support.

Introduction: The ADJ Hydro Beam X2 is a DMX intelligent, IP rated, high powered, moving head fixture.
To optimize the performance of this product, please read these operating instructions carefully to
familiarize yourself with the basic operations of this unit. This product is intended to be used by

professionally trained personnel only and is not suitable for private use.

These instructions contain important safety information regarding the use and maintenance of this
unit. Please keep this manual with the unit, for future reference.

Customer Support: Contact ADJ Service for any product related service and support needs. Also visit

forums.adj.com with questions, comments or suggestions.

Parts: To purchase parts online visit:

http://parts.adj.com (US)
http://www.adjparts.eu (EU)

ADJ SERVICE USA - Monday - Friday 8:00am to 4:30pm PST
Voice: 800-322-6337 | Fax: [phone] | [e-mail]

ADJ SERVICE EUROPE - Monday - Friday 08:30 to 17:00 CET
Voice: [phone] | Fax: [phone] | [e-mail]

ADJ PRODUCTS LLC USA

6122 S. Eastern Ave. Los Angeles, CA. 90040
323-582-2650 | Fax [phone] | www.adj.com | [e-mail]

ADJ SUPPLY Europe B.V

Junostraat 2 6468 EW Kerkrade, The Netherlands
[phone] | Fax [phone]

www.adj.eu | [e-mail]

ADJ PRODUCTS GROUP Mexico

AV Santa Ana 30 Parque Industrial Lerma, Lerma, Mexico 52000
[phone]

Caution! There are no user serviceable parts inside this unit. Do not attempt any repairs yourself,
doing so will void your manufactures warranty. In the unlikely event your unit may require service
please contact ADJ Products, LLC.

PLEASE recycle the shipping carton when ever possible.

ADJ Products, LLC - www.adj.com - Hydro Beam X2 User Manual Page 3

Hydro Beam X2 Features

• IP65 Outdoor Rated

• Electronic Dimming 0-100%

• DMX-512 protocol

• IP65 Locking 5-Pin XLR Connectors In & Out

• Multiple DMX Modes

• IP65 Locking Power Connectors In & Out

• Colors: 10 + Open (Including 3200K, 5600K, UV, and Quad Split Color)

• Gobos: 11 Rotating/Replaceable Gobos + Open

• Prism 1: Rotating 6-Facet Linear

• Prism 2: Rotating 8-Facet Circular

• Frost Effect

• Motorized Focus

• Multiple Unit Power Linking (See page 43)

Included:
1 x IP65 Locking Power Cable
2 x Omega Brackets

Hydro Beam X2 Warranty Registration

The Hydro Beam X2 carries a 2 year limited warranty. Please fill out the enclosed warranty card to
validate your purchase. All returned service items whether under warranty or not, must be freight pre­paid and accompany a return authorization (R.A.) number. The R.A. number must be clearly written on
the outside of the return package. A brief description of the problem as well as the R.A. number must
also be written down on a piece of paper included in the shipping carton. If the unit is under war­ranty, you must provide a copy of your proof of purchase invoice. You may obtain a R.A. number by
contacting our customer support team on our customer support number. All packages returned to the
service department not displaying a R.A. number on the outside of the package will be returned to the

shipper.

ADJ Products, LLC - www.adj.com - Hydro Beam X2 User Manual Page 4

Hydro Beam X2 IP Notice

IP65 RATED

An IP rated lighting xture is one, which is commonly installed in outdoor environments
and has been designed with an enclosure that eectively protects the ingress (entry)
of external foreign objects such as dust and water. The International Protection (IP)
rating system is commonly expressed as "IP" (Ingress Protection) followed by two
numbers (i.e. IP65) where the numbers dene the degree of protection. The rst digit
(Foreign Bodies Protection) indicates the extent of protection against particles entering
the xture and the second digit (Water Protection) indicates the extent of protection
against water entering the xture. An IP65 rated lighting xture is one, which has been
designed and tested to protect against the ingress of dust (6) and low-pressure water
jets from any direction (5).

MARINE/COASTAL ENVIRONMENT INSTALLATIONS

NOT suitable for marine and/or coastal environment installations. Installing
this xture in a marine and/or coastal environment may cause corrosion and/
or excessive wear to the interior and/or exterior components of the xture.

Damages and/or performance issues resulting from installation in a marine
and/or coastal environment will void the manufactures warranty and will NOT be subject
to any warranty claims and/or repairs.

ADJ Products, LLC - www.adj.com - Hydro Beam X2 User Manual Page 5

Hydro Beam X2 Safety Guidelines

FOR YOUR OWN PERSONAL SAFETY, PLEASE READ AND UNDERSTAND THIS MANUAL COMPLETELY

BEFORE YOU ATTEMPT TO INSTALL OR OPERATE THIS UNIT!

• THERE ARE NO USER SERVICEABLE PARTS INSIDE THIS UNIT. DO NOT ATTEMPT ANY REPAIRS
YOURSELF; DOING SO WILL VOID YOUR MANUFACTURES WARRANTY. DAMAGES RESULTING FROM
MODIFICATIONS TO THIS FIXTURE AND/OR THE DISREGARD OF SAFETY INSTRUCTIONS AND
GUIDELINES IN THIS MANUAL VOID THE MANUFACTURES WARRANTY AND ARE NOT SUBJECT TO
ANY WARRANTY CLAIMS AND/OR REPAIRS.

• DO NOT PLUG THE FIXTURE INTO A DIMMER PACK!
NEVER OPEN THIS FIXTURE WHILE IN USE!
UNPLUG POWER BEFORE SERVICING FIXTURE!
NEVER TOUCH THE FIXTURE DURING OPERATION AS IT MAY BE HOT!
KEEP FLAMMABLE MATERIALS AWAY FROM FIXTURE!

• ENSURE ALL CONNECTIONS AND END CAPS ARE PROPERLY SEALED WITH A DIELECTRIC GREASE
(AVAILABLE AT MOST ELECTRICAL SUPPLIERS) TO PREVENT WATER CORROSION AND/OR
ELECTRICAL SHORT CIRCUIT.

• IF THE FIXTURE IS EXPOSED TO ENVIRONMENTAL TEMPERATURE CHANGES SUCH AS RELOCATION
FROM AN OUTDOOR COLD TO AN INDOOR WARM ENVIRONMENT, DO NOT POWER THE FIXTURE
ON IMMEDIATELY. INTERNAL CONDENSATION AS A RESULT OF ENVIROMENTAL TEMPERATURE
CHANGE CAN CAUSE INTERNAL FIXTURE DAMAGE. LEAVE THE FIXTURE POWERED OFF UNTIL IT HAS
REACHED ROOM TEMPERATURE BEFORE POWERING ON.

• NEVER LOOK DIRECTLY INTO THE LIGHT SOURCE! RETINA INJURY RISK - MAY INDUCE BLINDNESS!
SENSITIVE PERSONS MAY SUFFER AN EPILEPTIC SHOCK!

• Be sure that the local power outlet is compatible with the required voltage for your unit.

• Do not attempt to operate this unit if the power cord has been frayed or broken.

• Do not attempt to remove or break o the ground prong from the electrical cord. This prong is used to
reduce the risk of electrical shock and re in case of an internal short.

• Disconnect from main power before making any type of connection.

• Do not remove the cover under any conditions. There are no user serviceable parts inside.

• Never operate this unit when it’s cover is removed.

• Always be sure to mount this unit in an area that will allow proper ventilation. Allow about 6” (15cm) between this
device and a wall.

• Do not attempt to operate this unit, if it becomes damaged.

• Always mount this unit in safe and stable matter.

• Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed
upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point
where they exit from the appliance.

• Cleaning -The fixture should be cleaned only as recommended by the manufacturer. See page 43 for cleaning
details.

• Heat -This fixture should be situated away from heat sources such as radiators, heat registers, stoves, or other
appliances (including amplifiers) that produce heat.

• The fixture should be serviced by qualified service personnel when the appliance does not appear to operate
normally or exhibits a marked change in performance.

ADJ Products, LLC - www.adj.com - Hydro Beam X2 User Manual Page 6

Hydro Beam X2 Safety Guidelines

PROTECTION CLASS 1 - FIXTURE MUST BE PROPERLY GROUNDED

SENSITIVE PERSONS MAY SUFFER AN EPILEPTIC SHOCK!

SAFETY G U I DELI NES

To guarantee a smooth operation, it is important to follow all instructions and guidelines in
this manual. ADJ Products, LLC is not responsible for injury and/or damages resulting
from the misuse of this fixture due to the disregard of the information printed in this
manual. Only qualified and/or certified personnel should perform installation of this fixture
and only the original rigging parts included with this fixture should be used for installation.
Any modifications to the fixture and/or the included mounting hardware will void the
original manufactures warranty and increase the risk of damage and/or personal injury.

THERE ARE NO USER SERVICEABLE PARTS INSIDE THIS UNIT.
DO NOT ATTEMPT ANY REPAIRS YOURSELF; DOING SO WILL VOID
YOUR MANUFACTURES WARRANTY. DAMAGES RESULTING FROM
MODIFICATIONS TO THIS FIXTURE AND/OR THE DISREGARD OF
SAFETY INSTRUCTIONS AND GUIDELINES IN THIS MANUAL VOID
THE MANUFACTURES WARRANTY AND ARE NOT SUBJECT TO ANY
WARRANTY CLAIMS AND/OR REPAIRS.

DO NOT PLUG FIXTURE INTO A DIMMER PACK!
NEVER OPEN THIS FIXTURE WHILE IN USE!
UNPLUG POWER BEFORE SERVICING FIXTURE!
NEVER TOUCH FIXTURE DURING OPERATION AS IT MAY BE HOT!
KEEP FLAMMABLE MATERIALS AWAY FROM FIXTURE!

ENSURE ALL CONNECTIONS AND END CAPS ARE PROPERLY
SEALED WITH A DIELECTRIC GREASE (AVAILABLE AT MOST
ELECTRICAL SUPPLIERS) TO PREVENT WATER CORROSION AND/OR
ELECTRICAL SHORT CIRCUIT.

IF THE FIXTURE IS EXPOSED TO ENVIRONMENTAL TEMPERATURE
CHANGES SUCH AS RELOCATION FROM AN OUTDOOR COLD TO AN
INDOOR WARM ENVIRONMENT, DO NOT POWER THE FIXTURE ON
IMMEDIATELY. INTERNAL CONDENSATION AS A RESULT OF
ENVIRONMENTAL TEMPERATURE CHANGE CAN CAUSE INTERNAL
FIXTURE DAMAGE. LEAVE THE FIXTURE POWERED OFF UNTIL IT
HAS REACHED ROOM TEMPERATURE BEFORE POWERING ON.

NEVER LOOK DIRECTLY INTO THE LIGHT SOURCE!
RETINA INJURY RISK - MAY INDUCE BLINDNESS!

ADJ Products, LLC - www.adj.com - Hydro Beam X2 User Manual Page 7

Hydro Beam X2 Safety Guidelines

S A FETY GUI D ELI N E S

RISK GROUP 3 - RISK OF EXPOSURE TO ULTRAVIOLET UV

RADIATION! FIXTURE EMITS HIGH INTENSITY WAVELENGTH

OF ULTRAVIOLET UV LIGHT FROM THE UV COLOR FILTER.

WEAR PROPER EYE AND SKIN PROTECTION. AVOID

PROLONGED PERIODS OF EXPOSURE TO UV COLOR FILTER.

AVOID WEARING WHITE COLOR CLOTHING AND/OR USING

UV PAINTS ON SKIN. AVOID DIRECT EYE AND/OR SKIN

EXPOSURE AT DISTANCES LESS THAN 11 feet (3.3m). DO NOT OPERATE FIXTURE

WITH DAMAGED/MISSING EXTERNAL COVERS. DO NOT LOOK DIRECTLY INTO THE

UV LIGHT AND/OR VIEW UV LIGHT DIRECTLY WITH OPTICAL INSTRUMENTS THAT

MAY CONCENTRATE THE LIGHT/RADIATION OUTPUT. INDIVIDUALS SUFFERING

FROM A RANGE OF EYE CONDITIONS, SUNLIGHT EXPOSURE DIS-ORDERS, OR

INDIVIDUALS USING PHOTOSENSITIVE MEDICATION, MAY RECEIVE DISCOMFORT

IF EXPOSED TO THE ULTRAVIOLET UV LIGHT EMITTED FROM THE UV LED.

DO NOT TOUCH the fixture housing during operation. Turn OFF the power and allow

approximately 60 minutes for the fixture to cool down before servicing.

DO NOT shake fixture; avoid brute force when installing and/or operating fixture.

DO NOT operate fixture if the power cord has become frayed, crimped, damaged and/or if any

of the power cord connectors are damaged and do not insert into the fixture securely with

NEVER force a power cord connector into the fixture. If the power cord or any of its
connectors are damaged, replace it immediately with a new one of similar power rating.

DO NOT block any air ventilation slots; these must remain clean and never blocked.

Allow approx. 6” (15cm) between fixture and other devices or a wall for proper cooling.

When installing fixture in a suspended environment, always use mounting hardware that is no
less than M10 x 25 mm, and always attach an appropriately rated safety cable.

ALWAYS disconnect fixture from main power source before performing any type of service
and/or cleaning procedure. Only handle the power cord by the plug end; never pull out the
plug by tugging the wire portion of the cord.

During the initial operation of this fixture, a light smoke or smell may emit from the interior
of the fixture. This is a normal process and is caused by excess paint in the interior of the casing
burning off from the heat associated with the lamp and will decrease gradually over time.

ease.

Consistent operational breaks will ensure fixture will function properly for many years.

ONLY use the original packaging and materials to transport the fixture in for service.

ADJ Products, LLC - www.adj.com - Hydro Beam X2 User Manual Page 8

Hydro Beam X2 Safety Guidelines

POTENTIAL INTERNAL FIXTURE DAMAGE FROM EXTERNAL SOURCES OF LIGHT BEAMS

External sources of light beams from direct sunlight, lighting moving head xtures, and lasers, which
are focused directly towards the exterior housing and/or penetrate the front lens opening of ADJ
lighting xtures, can cause severe internal damage including burning to optics, dichroic color lters,
glass and metal gobos, prisms, animation wheels, frost lters, iris, shutters, motors, belts, wiring,
discharge lamps, and LEDs.

This issue is not specic only to ADJ lighting xtures, it is a common issue with lighting xtures
from all manufacturers. Although there is no true way to fully prevent this issue from happening, the
guidelines below can prevent any potential damage from occurring if followed. Contact ADJ Service
for more details.

DO NOT EXPOSE THE FIXTURE AND/OR FRONT LENS OPENING TO LIGHT BEAMS FROM DIRECT
SUNLIGHT, OTHER LIGHTING MOVING HEAD FIXTURES, AND LASERS WHILE UNPACKING,
INSTALLATION, USE, AND EXTENDED IDLE TIMES OUTDOORS.
DO NOT FOCUS A LIGHT BEAM FROM ONE LIGHTING FIXTURE DIRECTLY TOWARDS ANOTHER.

ADJ Products, LLC - www.adj.com - Hydro Beam X2 User Manual Page 9

Hydro Beam X2 Overview

MENU

ENTER

3 4 5 96 87 10111

2

1. Lens

2. MENU Button

3. ENTER Button

4. LCD Menu Control Display

5. DOWN Button

6. UP Button

7. IP65 Locking 5-Pin XLR Connector OUT

8. IP65 Locking 5-Pin XLR Connector IN

9. Gore Valve

10. IP65 Locking Power Connector IN

11. IP65 Locking Power Connector OUT

ADJ Products, LLC - www.adj.com - Hydro Beam X2 User Manual Page 10

Hydro Beam X2 Discharge Lamp Warning

D I SCHARGE L A M P W ARNI N G

This fixture is fitted with a DISCHARGE LAMP, which is highly
susceptible to damage if improperly handled. NEVER touch the
lamp with your bare hands as the oil from your hands will shorten
the life of the lamp. Also, NEVER move the fixture until the lamp
has had ample time to cool. Lamps are NOT covered under
warranty conditions. Avoid switching the fixture ON and OFF
repeatedly in short intervals as this will reduce lamp life and
intensity. To achieve the intensity associated with discharge
lamps, these lamps use gas sealed in a high-pressure
environment to emit a brilliant output.

Due to the high pressure involved with the construction of the lamp, the lamp MAY

EXPLODE DURING PROLONGED EXTENSIVE USE. This risk is increased with age;

added care is encouraged when dealing with older lamps. Thus, the lamp must always

be replaced at the end of their recommended duty cycle. Extreme caution should be

used when operating this or any fixture fitted with a gas discharge lamp.

U V RADI ATI ON NOT I C E

This fixture emits intense UV radiation, which is harmful to the

eyes and skin.

severe damage to the retina. NEVER operate this fixture with

ANY of the protective covers removed. These covers have been

specially designed to shield against UV radiation.

The intense luminance of the lamp can cause

ADJ Products, LLC - www.adj.com - Hydro Beam X2 User Manual Page 11

Hydro Beam X2 Discharge Lamp Warning

LAMP REPLACEMENT WARNING

NOTE: The lamp life is represented in “Percentages”.

When the unit reaches 15% of lamp life left, the display will ash the message “Replace The Lamp Soon”.
This message will ash for up to 10 minutes. To conrm this warning and return to normal operation,

press the ENTER button.

When the unit reaches 10% of lamp life left, the display will again ash the message “Replace The Lamp
Soon”. This message will ash for up to 10 minutes. To conrm this warning and return to normal

operation, press the ENTER button. NOTE: When the xture is powered OFF and then back ON
again, the xture display will ash the following message: “Replace The Lamp Soon”.

When the unit reaches between 5%-0%% of lamp life left, the display will ash the message
“Replace The Lamp Immediately”. The unit will now NO longer respond to DMX commands and

enter hibernation mode which will discontinue all xture functionality with the exception of a few
menu commands.The xture will continue to enter into hibernation mode until the lamp is replaced
and the lamp time (LAMP ON TIME-R) has been reset. See page 36 “LAMP ON TIME-R” under the

“TOTAL LAMP TIME” submenu.

NOTE: After replacing the lamp, the lamp time MUST be reset. The lamp time must be reset to
gain access to the full system menu.

Lamp Life may vary depending on several factors including but not limited to:

Enviromental Conditions, Power/Voltage, Usage Patterns (On-O Cycling), Control,

and Dimming.

ADJ Products, LLC - www.adj.com - Hydro Beam X2 User Manual Page 12

Hydro Beam X2 Lamp Installation

LAMP INSTALLATION

WARNING! LAMP REPLACEMENT SHOULD ONLY BE DONE BY A TRAINED TECHNICIAN.

1. Turn OFF power and allow approximately 60 minutes for the xture to cool down.

2. Unscrew the (4x) allen head screws to remove the rear cover. When removing the rear cover,
please be advised that the cover is connected to the unit via a safety cable and connected wire

cable.

3. Gently remove the (2x) spade terminals
connected to the lamp.

4. Loosen the Phillips head screw to unlock
the lamp holding slider.

ADJ Products, LLC - www.adj.com - Hydro Beam X2 User Manual Page 13

Hydro Beam X2 Lamp Installation

5. Carefully slide the lamp to the right and tighten the Phillips head screw. Carefully remove the lamp
from its holder and replace with the same type lamp.

6. Once the new lamp has been inserted, loosen the Phillips head screw again to allow the lamp
holding mechanism to slide back to its closed position. Tighten the Phillips head screw.

Reconnect the (2x) spade terminal and replace the cover and tighten the (4x) Allen screws.

ADJ Products, LLC - www.adj.com - Hydro Beam X2 User Manual Page 14

Hydro Beam X2 Torque Settings & IP Tester

TORQUE SETTINGS FOR SCREWS

ALL SCREWS MUST BE TIGHTENED WITH A TORQUE DRIVER. All screws are Allen Head

screws. Please see below for screw locations, screw quantity and torque settings. The number listed
in the “#” column corresponds to the location on the xture. See the xture diagram and number on
the next page for SCREW LOCATION depictions.

SCREW LOCATIONS TORQUE SETTING & TOOL SIZE#

1 Lens Assembly to Head Casting (x14) 6.5-8.7 In-Lb / 3mm Hex

2 Lamp Cover to Head Casting (x4) 6.7-9.6 In-Lb / 4mm Hex

3 Plastic Head Cover to Head Casting (4 x Each Side = 8 Total) 6.5-8.7 In-Lb / 3mm Hex

4 Yoke Arm Cover to Yoke Frame (11 x Each Side = 22 Total) 6.5-8.7 In-Lb / 3mm Hex

5 Access Cover to Yoke Frame (x4) Manual Screwdriver / 3mm Hex

6 Bottom Cover to Base Casting (x16) 6.7-9.6 In-Lb / 3mm Hex

7 Power & Data Connector to Base Casting (x8) 6.5-8.7 In-Lb / Torx T8

8 1/4 Turn Adaptor Plate to Bottom Cover (x16) 6.5-8.7 In-Lb / 3mm Hex

TORQUE DRIVERS (Recommended):
UTICA TS-30 (Shown)

ALTERNATIVE DRIVERS:
Proto J6107A
Wiha 28887

CAUTION! DO NOT OVER TORQUE SCREWS AS THIS CAN CAUSE LEAKAGE ISSUES!
TO CONFIRM THE IP65 INTENGRITY AFTER A LAMP REPLACEMENT, TEST THE FIXTURE
USING THE ELATION IP TESTER. CONTACT ELATION SERVICE FOR MORE DETAILS.

ADJ Products, LLC - www.adj.com - Hydro Beam X2 User Manual Page 15

Hydro Beam X2 Screw Locations

2

1

7

5

3

3

4 4

5

6

8

6

6

8

6

ADJ Products, LLC - www.adj.com - Hydro Beam X2 User Manual Page 16

Hydro Beam X2 Gobo Specifications

* * * IMPORTANT NOTICE REGARDING CUSTOM GOBOS * * *

Due to the extreme high temperature optical system, special BOROFLOAT glass material and design criteria
are required.

Due to varying gobo manufacturing processes and tolerances, it is highly recommended to provide a gobo
sample and gobo holder/wheel sample from the xture to the custom gobo vendor for accurate sizing. Gobo
specications below including diameter, thickness, and materials have been tested and are compatible in
this xture.

Using custom gobos that do not match the gobo specications below, is not recommended and any damage
to the xture as a result of using a custom gobo is NOT covered under warranty. Extended testing of custom
gobo designs is highly recommended prior to using.

PLEASE CONTACT ADJ CUSTOMER SUPPORT FOR FURTHER INFORMATION.

ROTATING GLASS GOBOS

Gobo O.D. (Max. Outer Diameter) ø9.7mm

Gobo I.D. (Max. Image Diameter) ø6.5mm

Gobo Holder Diameter ø10mm

Gobo Thickness ø0.5mm

Gobo Material BOROFLOAT

Hydro Beam X2 Gobos

GOBO 1 GOBO 2 GOBO 3 GOBO 4 GOBO 5 GOBO 6

GOBO 7 GOBO 8 GOBO 9 GOBO 10 GOBO 11

ADJ Products, LLC - www.adj.com - Hydro Beam X2 User Manual Page 17

Hydro Beam X2 Gobo Installation

GOBO INSTALLATION

WARNING! GOBO REPLACEMENT SHOULD ONLY BE DONE BY A TRAINED TECHNICAN.

TURN OFF POWER AND ALLOW APPROXIMATELY 60 MINUTES FOR THE FIXTURE
TO COOL DOWN.

Unscrew and remove the 8 screws
that secure the moving head shells.

4 x Screws Total
2 x Screws on each side

4 x Screws Total
2 x Screws on
each side

ADJ Products, LLC - www.adj.com - Hydro Beam X2 User Manual Page 18

Hydro Beam X2 Gobo Installation

4 x Screws Total
2 x Screws on each side

4 x Screws Total
2 x Screws on
each side

Unscrew and remove the 8 screws
that secure the moving head shells.

Remove both moving head shells

10 x Screws Total
5 x Screws on each side

After the moving head shells have been removed unscrew and remove the 10 screws
that secure the head in place. Carefully remove the head to access the inside module.

ADJ Products, LLC - www.adj.com - Hydro Beam X2 User Manual Page 19

Hydro Beam X2 Gobo Installation

Guard Plate

2 x Screws

Guard Plate

Note: Disconnect the cables with RED sleeves before dismantling head module.

Head Module

Carefully remove the Head
Module.

ADJ Products, LLC - www.adj.com - Hydro Beam X2 User Manual Page 20

Hydro Beam X2 Gobo Installation

Note: Make sure the retainer spring is secure.

Unscrew and remove the 4 screws

that secure the Insulation Board.

4 x Screws Total

Insulation Board

Carefully remove
the Insulation Board

Gobo

Carefully lift the GOBO
holder up and out from
the GOBO wheel.

Retainer Spring

Gobo Replacement:
The GOBO is secured into the gobo housing
by a retainer spring. Carefully remove the
retainer spring that holds the GOBO in place.
Carefully remove the GOBO from the GOBO
holder. Replace with your desired GOBO, and
reinsert the retainer spring into place.

ADJ Products, LLC - www.adj.com - Hydro Beam X2 User Manual Page 21

Hydro Beam X2 Fixture Installation

F I XTU R E I N S T A LLA T I O N

Keep fixture at least 5.0 feet (1.5m) away from any

flammable materials, decorations, pyrotechnics, etc.

ELEC TRI C AL CONNE C T I ONS

A q ualif ied electri c i an shou l d b e used for all

electri cal c o nnect ions and/ o r i nstalla t i o ns.

MINIMUM DISTANCE TO OBJECTS/SURFACES

M UST BE 40 F EET ( 12 M E T ERS)

FLAMMA B LE M ATER I AL W A RNI N G

MAXIMUM TEMPERATURE OF EXTERNAL SURFACE

212° F ( 100° C )

DO NOT INSTALL THE FIXTURE IF YOU ARE NOT QUALIFIED TO DO SO!

Fixture MUST be installed following all local, national, and country commercial electrical and

construction codes and regulations. Before rigging/mounting the fixture to any metal

truss/structure or placing the fixture on any surface, a professional equipment installer

MUST be consulted to determine if the metal truss/structure or surface is properly certified

to safely hold the combined weight of the fixture, clamps, cables, and accessories.

Overhead fixture installation must always be secured with a secondary safety attachment,

such as an appropriately rated safety cable that meets all local, national, and country codes

and regulations.

Fixture ambient operating temperature range is -4° to 113°F. (-20° to 45°C)

Do not use this fixture outside this temperature range.

Fixture should be installed in areas outside walking paths, seating areas, or away from areas

were unauthorized personnel might reach the fixture by hand.

NEVER stand directly below the fixture when rigging, removing, or servicing.

Allow approximately 60 minutes for the fixture to cool down before servicing.

ADJ Products, LLC - www.adj.com - Hydro Beam X2 User Manual Page 22

Hydro Beam X2 Fixture Installation

NOTICE: The suitable enviromental temperature for this lighting xture is between -25˚ C to 45˚ C.

Do not place this lighting xture in an enviroment where the temperatures are under or above the
temperatures stated above. This will allow the xture to run at its best and help prolong the xture
life.

CLAMP

SAFETY CABLE

Screw one clamp via a M12 screw and nut into the Omega holder. Insert the quick-lock fasteners of
the Omega holder into the respective holes of the adjustable mounting bracket. Tighten the quick-lock
fasteners fully clockwise. Pull the safety-cable through the opening located on the bottom of the unit
and over the trussing system or a safe xation spot. Insert the end in the carabine and tighten the
safety screw.

OMEGA BRACKET

ADJ Products, LLC - www.adj.com - Hydro Beam X2 User Manual Page 23

Hydro Beam X2 Fixture Installation

When installing the unit, the trussing or area of installation must be able to hold 10 times the weight
without any deformation. When installing the unit must be secured with a secondary safety attachment,
e.g. and appropriate safety cable. Never stand directly below the unit when mounting, removing, or

servicing the unit.

Overhead mounting requires extensive experience, including calculating working load limits, installation
material being used, and perodic safety inspection of all installation material and unit. If you lack
these qualications, do not attempt the installation yourself.

These installaiton should be checked by a skilled person once a year.

LCD CONTROL
DISPLAY

CABLES
DOWN

* S I D E M OUNT I N G

TO MAINTAIN IP65 RATING INTEGRITY, FIXTURE

MUST BE INSTALLED WITH CABLES FACING THE

GROUND AT ALL TIMES. WATER MUST EASILY

RUN OFF AND NOT COLLECT AROUND CABLE

CONNECTIONS.

LCD CONTROL
DISPLAY

CABLES
DOWN

* S A FETY CABL E

ALWAYS ATTACH A SAFETY CABLE WHENEVER

INSTALLING THIS FIXTURE IN A SUSPENDED

ENVIRONMENT TO ENSURE THE FIXTURE WILL

NOT DROP IF THE CLAMP FAILS.

The Hydro Beam X2 is fully operational in three dierent mounting positions, hanging upside-down,
mounted sideways on trussing, or set on a at level surface. Be sure this xture is kept at least 12m
(40ft) away from any ammable materials (decoration etc.). Always use and install the supplied safety
cable as a safety measure to prevent accidental damage and/or injury in the event the clamp fails
(see next page). Never use the carrying handles for secondary attachment.

ADJ Products, LLC - www.adj.com - Hydro Beam X2 User Manual Page 24

Hydro Beam X2 Connections

ENSURE ALL CONNECTIONS AND END CAPS ARE PROPERLY SEALED WITH A DIELECTRIC
GREASE (AVAILABLE AT MOST ELECTRICAL SUPPLIERS) TO PREVENT WATER CORROSION
AND/OR ELECTRICAL SHORT CIRCUIT.

TO MAINTAIN IP65 RATING INTEGRITY AND PREVENT WATER FROM ENTERING THE FIXTURE,
ALL UNUSED CONNECTION RUBBER CAPS MUST BE SEALED.

ADJ Products, LLC - www.adj.com - Hydro Beam X2 User Manual Page 25

Hydro Beam X2 DMX Set Up

DMX-512: DMX is short for Digital Multiplex. This is a universal protocol used as a form of communication

between intelligent fixtures and controllers. A DMX controller sends DMX data instructions from
the controller to the fixture. DMX data is sent as serial data that travels from fixture to fixture via the
DATA “IN” and DATA “OUT” XLR terminals located on all DMX fixtures (most controllers only have a
DATA “OUT” terminal).

DMX Linking: DMX is a language allowing all makes and models of dierent manufactures to be
linked together and operate from a single controller, as long as all xtures and the controller are DMX
compliant. To ensure proper DMX data transmission, when using several DMX fixtures try to use
the shortest cable path possible. The order in which fixtures are connected in a DMX line does not
influence the DMX addressing. For example; a fixture assigned a DMX address of 1 may be placed
anywhere in a DMX line, at the beginning, at the end, or anywhere in the middle. When a fixture is
assigned a DMX address of 1, the DMX controller knows to send DATA assigned to address 1 to that
unit, no matter where it is located in the DMX chain.

Data Cable (DMX Cable) Requirements (For DMX Operation): The Hydro Beam X2 can be controlled via
DMX-512 protocol. Your unit and your DMX controller requires a 5-pin XLR connector for data input and data
output. We recommend Accu-Cable DMX cables. If you are making your own cables, be sure to use
standard 110-120 Ohm shielded cable (This cable may be purchased at almost all pro lighting stores).
Your cables should be made with a male and female XLR connector on either end of the cable. Also
remember that DMX cable must be daisy chained and cannot be split.

Special Note: Line Termination.

on the last unit to avoid erratic behavior. A terminator is a 110-120 ohm 1/4 watt resistor which is con­nected between pins 2 and 3 of a male XLR connector (DATA + and DATA -). This unit is inserted in the
female XLR connector of the last unit in your daisy chain to terminate the line. Using a cable terminator
(ADJ part number Z-DMX/T) will decrease the possibilities of erratic behavior.

TO MAINTAIN IP65 RATING INTEGRITY AND PREVENT WATER FROM ENTERING THE FIXTURE,
ALL UNUSED CONNECTION RUBBER CAPS MUST BE SEALED AND ONLY IP65 RATED POWER
AND DATE CABLES MUST BE USED.

When longer runs of cable are used, you may need to use a terminator

ADJ Products, LLC - www.adj.com - Hydro Beam X2 User Manual Page 26

Hydro Beam X2 DMX Addressing

DMX ADDRESSING

All xtures should be given a DMX starting address when using a DMX controller, so the correct xture
responds to the correct control signal. This digital starting address is the channel number from which
the xture starts to “listen” to the digital control signal sent out from the DMX controller. The assignment
of this starting DMX address is achieved by setting the correct DMX address on the digital control
display on the xture.

You can set the same starting address for all xtures or a group of xtures, or set dierent addresses
for each individual xture. Setting all xtures to the same DMX address will cause all xtures to react
in the same way, in other words, changing the settings of one channel will aect all the xtures

simultaneously.

If you set each xture to a dierent DMX address, each unit will start to “listen” to the channel number
you have set, based on the quantity of DMX channels of each xture. That means changing the settings
of one channel will only aect the selected xture.

In the case of the Hydro Beam X2, when in 15 Channel you should set the starting DMX address of
the rst unit to 1, the second unit to 16 (15 + 1), the third unit to 31 (16 + 15), and so on. (See the chart
below for more details.)

Channel Mode

15 Channels 1 16 31 46

17 Channels 1 18 35 52

Unit1

Address

Unit2

Address

Unit3

Address

Unit4

Address

ADJ Products, LLC - www.adj.com - Hydro Beam X2 User Manual Page 27

Hydro Beam X2 DMX Channel Modes

15 Channels 17 Channels Values

1 1

2

2 3

4

3 5

000-255

000-255

000-255

000-255

000-007
008-009
010-011
012-013
014-015
016-017
018-019
020-021
022-023
024-025
026-027
028-029
030-031
032-033
034-035
036-037
038-039
040-041
042-043
044-045
046-047
048-049
050-051
052-053
054-055
056-057
058-059
060-061
062-063
064-127
128-189
190-193
194-255

Functions

PAN MOVEMENT 8-BIT:

Pan Movement (0° - 540°)

PAN FINE 16-BIT:

Fine Control of Pan Movement

TILT MOVEMENT 8-BIT:

Tilt Movement (0° - 270°)

TILT FINE 16-BIT:

Fine Control of Tilt Movement

COLOR WHEEL:

Open / White
White + Red
Red
Red + Orange
Orange
Orange + Light Blue
Light Blue
Light Blue + Green
Green
Green + Light Green
Light Green
Light Green + Purple
Purple
Purple + Pink
Pink
Pink + Yellow
Yellow
Yellow + Magenta
Magenta
Magenta + Blue
Blue
Blue + Red/Green/Blue/Orange (Quad)
Red/Green/Blue/Orange (Quad)
Red/Green/Blue/Orange (Quad) + CTO-3200K
CTO-3200K
CTO-3200K + CTO-5600K
CTO-5600K
CTO-5600K + UV
UV
Color Wheel Indexing
Clockwise Rotation Fast - Slow
Stop
Clockwise Rotation Slow - Fast

ADJ Products, LLC - www.adj.com - Hydro Beam X2 User Manual Page 28

Hydro Beam X2 DMX Channel Modes

15 Channels 17 Channels Values

000-009
010-014
015-019
020-024
025-029
030-034
035-039
040-044
045-049
050-054
055-059

4 6

5 7

6 8

7 9

8 10

9 11

060-063
064-068
069-073
074-078
079-083
084-088
089-093
094-098
099-103
104-108
109-113
114-118
119-127
128-189
190-193
194-255

000-127
128-189
190-193
194-255

000-007
008-255

000-127
128-189
190-193
194-255

000-007
008-255

000-127
128-189
190-193
194-255

Functions

GOBO WHEEL:

Open
Gobo 1
Gobo 2
Gobo 3
Gobo 4
Gobo 5
Gobo 6
Gobo 7
Gobo 8
Gobo 9
Gobo 10
Gobo 11
Open Shake
Gobo 1 Shake
Gobo 2 Shake
Gobo 3 Shake
Gobo 4 Shake
Gobo 5 Shake
Gobo 6 Shake
Gobo 7 Shake
Gobo 8 Shake
Gobo 9 Shake
Gobo 10 Shake
Gobo 11 Shake
Clockwise Rotation Fast - Slow
Stop
Counter-Clockwise Rotation Slow - Fast

ROTATING GOBO:

Indexing
Clockwise Rotation Fast - Slow
Stop
Counter-Clockwise Rotation Slow - Fast

PRISM 1 (6 FACET LINEAR):

Close
Open

ROTATING PRISM 1 (6 FACET LINEAR):

Indexing
Counter-Clockwise Rotation Fast - Slow
Stop
Clockwise Rotation Slow - Fast

PRISM 2 (8 FACET CIRCULAR):

Close
Open

ROTATING PRISM 2 (8 FACET CIRCULAR):

Indexing
Counter-Clockwise Rotation Fast - Slow
Stop
Clockwise Rotation Slow - Fast

ADJ Products, LLC - www.adj.com - Hydro Beam X2 User Manual Page 29

Hydro Beam X2 DMX Channel Modes

15 Channels 17 Channels Values

000-031
032-063

10 12

11 13

12 14

13 15

14 16

15 17

064-095
096-127
128-159
160-191
192-223
224-255

000-007
008-255

000-255

000-069
070-079
080-089
090-099
100-109
110-119
120-129
130-139
140-149
150-159
160-179
180-189
190-199
200-209
210-229
230-239
240-255

Functions

SHUTTER & STROBING:

Close
Open
Strobing Slow - Fast
Open
Pulsating Strobe Slow - Fast
Open
Random Strobing
Open

MASTER DIMMER:

0% - 100% 000-255

FOCUS:

0% - 100%000-255

FROST:

Off
On

PAN/TILT MOVEMENT SPEED:

Fast - Slow

SPECIAL FUNCTIONS:

No Function
Blackout W/ Pan/Tilt Movement Enabled
Blackout W/ Pan/Tilt Movement Disabled
Blackout W/ Color Wheel Movement Enabled
Blackout W/ Color Wheel Movement Disabled
Blackout W/ Gobo Wheel Movement Enabled
Blackout W/ Gobo Wheel Movement Disabled
Lamp On
Reset Pan & Tilt Motors
Reset Effect Motors
No Function
Lamp Full Power
Lamp Half Power
Reset All
No Function
Lamp Off
No Function

ADJ Products, LLC - www.adj.com - Hydro Beam X2 User Manual Page 30

Hydro Beam X2 System Menu

SYSTEM MENU

The xture includes an easy to navigate system menu control panel display where all necessary
settings and adjustments are made. (See image below) During normal operation, pressing the MENU
button once will access the xture’s main menu. Once in the main menu, you can navigate through
the dierent functions and access the sub-menus with the UP and DOWN buttons. When you reach
a eld that requires adjusting, press the ENTER button to access that eld and use the UP and
DOWN buttons to adjust the eld. Pressing the ENTER button once more will conrm your setting.
You may exit the main menu at any time without making any adjustments by pressing the MENU

button.

SYSTEM LOCK/UNLOCK: When the display lock function is activated, the display and system
menu will lock after 10 seconds of no activity. To UNLOCK the display, press and HOLD the MENU
button for 10+ seconds.
While pressing the MENU button, a timer will appear at the bottom of the display indicating the pass­ing seconds from 0-9. Once the timer reaches 9 seconds, the display will unlock allowing access to

the system menu.

DO NOT RELEASE THE MENU BUTTON UNTIL THE DISPLAY IS UNLOCKED.

If the MENU button is released before the timer reaches 9 seconds and/or is unlocked, the display
will not unlock and the time will be reset.

NOTE: The timer will not appear in the display if the lock function is disabled.

MENU

ENTER

ADJ Products, LLC - www.adj.com - Hydro Beam X2 User Manual Page 31

Hydro Beam X2 System Menu

MENU OPTIONS DESCRIPTIONSUBMENU

DMX SETTINGS

PERSONALITY

MANUAL
CONTROL

DMX Address

DMX CH Mode

No DMX Status

Select Signal

Status Settings

WiFly Settings

Reset Motors

Display

Service

Pan
Tilt
Color
Gobo
RGobo
Prism1
RPrism1
Prism2
RPrism2
Shutter
Dimmer
Frost
Focus

001-512

15Ch / 17Ch

Hold Last / Blackout / Manual

DMX: Yes / No

WiFly: Yes / No

WiFly and DMX Out: Yes / No

Pan Invert: On / Off

Tilt Invert: On / Off

P./T. Feedback: On / Off

Pan Degree: 540

P./T. Speed: Speed 1 / Speed 2

Hibernation: Off / 01M~99M / 15M

Set WiFly Channel: 00~14

Enable / Disable WiFly

Reset All Motors: Yes / No

Pan/Tilt Reset: Yes / No

Color Reset: Yes / No

Gobo/R-G Reset: Yes / No

Prism1/R-P1 Reset: Yes / No

Prism2/R-P2 Reset: Yes / No

Shutter Reset: Yes / No

Focus Reset: Yes / No

Frost Reset: Yes / No

Intensity: 1~10 (Dimmest-Brightest)

Display Invert: Yes / No

Screen Saver Delay: Off~10M
Lock On/Off: On / Off

Calibration

Pass Code = 050

000-255
000-255
000-255
000-255
000-255
000-255
000-255
000-255
000-255
000-255
000-255
000-255
000-255

(Pass Code = 050)

Factory Restore: Yes / No
(Pass Code = 011)

DMX Addressing

DMX Channel Mode
Selection

DMX Lost Status

Control via DMX

Control via WiFly
Control via WiFly and send

DMX Out via DMX cable
Reverse Pan Motion

Reverse Tilt Motion

Pan/Tilt Movement Feedback

Pan Degree

Pan/Tilt Movement Speed

Sleep Setting (No Activity)

Set WiFly Wireless Channel

Activate / Deactivate WiFly

Reset All Motors

Reset the Pan & Tilt Motors

Reset the Color Wheel Motor

Reset the Gobo Wheel Motors

Reset the Prism 1 Motors

Reset the Prism 2 Motors

Reset the Shutter Motor

Reset the Focus Motor

Reset the Frost Motor

Display Brightness

Display Readout Inversion

Display Shutoff Time
Display Lock

Calibration Adjustment

Restore Factory Settings

Manual Control

ADJ Products, LLC - www.adj.com - Hydro Beam X2 User Manual Page 32

Hydro Beam X2 System Menu

MENU OPTIONS DESCRIPTIONSUBMENU

INFORMATION

Fixture Life Time

Total Lamp Time

Fixture Temps

Power On Time: XXXXXX Hours

P-On Time-R: XXXXXX Hours

P-On Time Reset: Pass Code = 050

Lamp On Time - XXXXXX Hours

Lamp On Time-R - XXXXXX Hours

Lamp On Time Reset: Pass Code = 050

LampLifeTime: XXX%

Current: XXX ˚F / XXX ˚C

Max Resettable: XXX ˚F / XXX ˚C

Head

Max Not Resettable: XXX ˚F / XXX ˚C

Current: XXX ˚F / XXX ˚C

Max Resettable: XXX ˚F / XXX ˚C

Base

Max Not Resettable: XXX ˚F / XXX ˚C

Reset Head Temp: Yes / No (Pass Code = 050)

Reset Base Temp: Yes / No (Pass Code = 050)

Total Running Time
(Not Resettable)

Total Running Time
(Resettable)

Reset P-On Time-R
(Total Running Time)

Lamp On Time
(Not Resettable)

Lamp On Time
(Resettable)

Reset Lamp On Time-R
(Lamp On Time)

Current Lamp Life Percentage

Current Head Temperature

Maximum Temperature

(1)

Reached (Resettable)

(See Note 1)

(2)

Maximum Temperature
Reached (Not Resettable)

(See Note 2)

Current Base Temperature

(1)

Maximum Temperature
Reached (Resettable)

(See Note 1)

Maximum Temperature

(2)

Reached (Not Resettable)

(See Note 2)

Reset Head Temperature
(Max Resettable)

Reset Base Temperature
(Max Resettable)

Humidity

Fan Info. (RPM)

DMX Values

(See Note 3)

(3)

Head Humidity: XXX%

Base Humidity: XXX%

Base Fan 1: XXXX
Base Fan 2: XXXX
Base Fan 3: XXXX
Arm Fan 1: XXXX
Arm Fan 2: XXXX
Head Fan 1: XXXX
Head Fan 2: XXXX
Head Fan 3: XXXX
Head Fan 4: XXXX
Head Fan 5: XXXX
Head Fan 6: XXXX
Head Fan 7: XXXX

Pan / Pan Fine / Tilt / Tilt Fine / Color / Gobo /
RGobo / Prism1 / RPrism1 / Prism2 / RPrism2 /
Shutter / Dimmer / Focus / Frost / P/T Speed /

Current Head Humidity

Current Base Humidity

Base Fan 1 Speed
Base Fan 2 Speed
Base Fan 3 Speed
Arm Fan 1 Speed
Arm Fan 2 Speed
Head Fan 1 Speed
Head Fan 2 Speed
Head Fan 3 Speed
Head Fan 4 Speed
Head Fan 5 Speed
Head Fan 6 Speed
Head Fan 7 Speed

Current DMX Values

Spe. Func

ADJ Products, LLC - www.adj.com - Hydro Beam X2 User Manual Page 33

Hydro Beam X2 System Menu

MENU OPTIONS DESCRIPTIONSUBMENU

INFORMATION

Error Logs

Fixture Errors (Listed Errors One by One)

Reset Error Log: Yes / No (Pass Code = 050)

Software Version Current Software VersionX.XX

Last 10 Fixture Error Codes

Clear the Error Log

Lamp ON / OFF

Lamp ON

LAMP CONTROL

Notes:
(1) Current Maximum Temperature - Maximum fixture temp. that has been recorded, before reset and after reset.
(2) Maximum Temperature - Overall maximum fixture temp. that has been recorded. (Not Resettable)
(3) DMX Value options depend on the DMX Channel mode the fixture is set to

with Power

Lamp ON via DMX On / Off

Lamp OFF via DMX On / Off

On / Off

On / Off

Lamp On/Off

Lamp ON when Power ON

Lamp Power ON via DMX

Lamp Power OFF via DMX

ADJ Products, LLC - www.adj.com - Hydro Beam X2 User Manual Page 34

Hydro Beam X2 System Menu

DMX SETTINGS - The submenus listed under DMX SETTINGS are as follows: DMX Address, DMX
Channel Mode, No DMX Status, and Select Signal.

- DMX ADDRESS - In this submenu you can use the UP or DOWN buttons to adjust and nd your

desired DMX address.

- DMX CHANNEL MODE - In this submenu you can use the UP or DOWN buttons to nd your
desired DMX channel mode.

- NO DMX STATUS - This submenu setting is used as a precaution mode in case the DMX signal is
lost or interrupted. The operating mode chosen in this submenu is the running mode the xture
will go into when the DMX signal is lost. Listed below are the 2 modes.

• HOLD - This setting will have the xture stay in the last DMX setup.

• BLACKOUT - This setting will have the xture automatically go into stand by mode.

• MANUAL - This setting will go into the current manual control set up. See MANUAL CONTROL.

PERSONALITY - The submenus listed under PERSONALITY are as follows: Select Signal, Status
Settings, WiFly Settings, Reset Motors, Display, and Service.

- SELECT SIGNAL - In this submenu you can select your desired DMX control mode:

• DMX - Control the unit via DMX cable connection.

• WiFly - Control the unit via WiFly connection.

• WiFly / DMX Out - Control the unit via WiFly connection. The DMX signal is sent to the next unit
via DMX cable.

- STATUS SETTINGS - In this submenu you are able to access and adjust/change: Pan Invert, Tilt
Invert, P./T. Feedback, Pan Degree, P./T. Speed, and Hibernation.

- WIFLY SETTINGS - In this submenu you are able to access and adjust/change: WiFly Channel
and Enable/Disable WiFly.

- RESET MOTORS - In this submenu you are able to reset selected motors.

- DISPLAY - In this submenu you are able to access and adjust/change: Backlight Intensity, Display

Invert, Screen Saver Delay, and Display Lock.

- SERVICE - In this submenu you are able to access and adjust/change: the calibration (eect
adjust) and restore the factory settings.

MANUAL CONTROL - This menu is for manual testing and manual control. Pan, tilt, color wheel,
gobo wheel, gobo rotation, prism 1, prism 1 rotation, prism 2, prism 2 rotation, shutter, dimmer, frost,
and focus can all be tested/adjusted.

ADJ Products, LLC - www.adj.com - Hydro Beam X2 User Manual Page 35

Hydro Beam X2 System Menu

INFORMATION - The submenus listed under INFORMATION are as follows: Fixture Life Time,
Total Lamp Time, Fixture Temps, Humidity, Fan Info. (RPM), DMX Values, Error Logs, and Software
Version.

- FIXTURE LIFE TIME

• Power On Time -The TOTAL power ON running time of the unit is displayed. This time CANNOT
be reset. Reminder: The displayed time represents the TOTAL POWER ON time.

• P-On Time-R - The CURRENT power ON running time of the unit is displayed. This running time
may not be the same as the total power ON running time displayed under “Power On Time”. This

time CAN be reset. Reminder: The displayed time represents the CURRENT POWER ON TIME
since the last reset.

• P-On Time Reset - Reset the CURRENT power ON running time that is displayed under “P-On Time-R”.

- TOTAL LAMP TIME

• Lamp On Time - The TOTAL Lamp ON time is displayed. This total lamp ON time CANNOT be
reset. Reminder: The displayed time represents the TOTAL LAMP ON time.

• Lamp On Time-R - The CURRENT LED ON running time is displayed. This running time may not
be the same as the total lamp ON time displayed under “Lamp On Time”. This total lamp ON

time CAN be reset. Reminder: The displayed time represents the CURRENT LAMP ON time
since the last reset.

• Lamp On Time Reset - With this function you can reset the CURRENT lamp ON time that is displayed
under “Lamp On Time-R”.

• LampLifeTime - With this function you can check the current lamp life percentage.

- FIXTURE TEMPS

• Head
Current - Current temperature of the moving head is displayed.
Max Resettable - Maximum moving head temperature that has been recorded, before reset

and after reset. (Resettable)

Max Not Resettable - Overall maximum moving head temperature that has been recorded.
(Not Resettable)

• Base
Current - Current temperature of the base is displayed.

Max Resettable - Maximum base temperature that has been recorded, before reset and after
reset. (Resettable)
Max Not Resettable - Overall maximum moving head temperature that has been recorded.
(Not Resettable)

Reset Head Temp - Reset the “MAX RESETTABLE” moving head temperature. (Pass Code is “50”)

Reset Base Temp - Reset the “MAX RESETTABLE” base temperature. (Pass Code is “50”)

ADJ Products, LLC - www.adj.com - Hydro Beam X2 User Manual Page 36

Hydro Beam X2 System Menu

- HUMIDITY
Head Humidity - The current humidity of the moving head is displayed.

Base Humidity - The current humidity of the base is displayed.

- FAN INFO. (RPM)
Base Fan1 - Current speed of base fan 1 is displayed.

Base Fan2 - Current speed of base fan 2 is displayed.

Base Fan3 - Current speed of base fan 3 is displayed.

Arm Fan1 - Current speed of arm fan 1 is displayed.

Arm Fan2 - Current speed of arm fan 2 is displayed.

Head Fan1 - Current speed of moving head fan 1 is displayed.

Head Fan2 - Current speed of moving head fan 2 is displayed.

Head Fan3 - Current speed of moving head fan 3 is displayed.

Head Fan4 - Current speed of moving head fan 4 is displayed.

Head Fan5 - Current speed of moving head fan 5 is displayed.

Head Fan6 - Current speed of moving head fan 6 is displayed.

Head Fan7 - Current speed of moving head fan 7 is displayed.

- DMX Values - Displays the DMX values of any DMX channel that is currently in use.

- Error Logs - Displays any error codes.

- Software Version - Current software version is displayed.

LAMP CONTROL - The submenus listed under LAMP CONTROL are as follows: Lamp ON/OFF,
Lamp ON with Power, Lamp ON via DMX, and Lamp OFF via DMX.

- Lamp ON/OFF - Turn the lamp On/O.

- Lamp ON with Power - Lamp powers “ON” when power is applied.

- Lamp ON via DMX - Power lamp “ON” using a DMX controller.

- Lamp OFF via DMX - Power lamp “OFF” using a DMX controller.

ADJ Products, LLC - www.adj.com - Hydro Beam X2 User Manual Page 37

Hydro Beam X2 WiFly Control

BEFORE SETTING THE WIRELESS CHANNEL ON ANY WIFLY FIXTURE, MAKE SURE
THE SOURCE WIFLY WIRELESS DMX TRANSCEIVER DEVICE IS OFF.

With this feature you are able to control the unit with DMX without the need of XLR cables. Your
DMX controller must be connected to a ADJ WiFly Transceiver to use this function. You are able to
communicate up to 2500 feet/760 meters (open line of sight).

1. Ensure the source WiFly wireless DMX Transceiver device is powered OFF.

2. Power ON the fixture and using the control panel scroll to the PERSONALITY menu and press

ENTER. Use the UP and DOWN buttons to highlight the WIFLY SETTINGS submenu and press
ENTER.

3. Using the UP and DOWN buttons, highlight ENABLE/DISABLE WIFLY. Press the ENTER button
to toggle between ENABLE & DISABLE. Press ENTER so that “Enable” is displayed.

4. Next highlight SET WIFLY CHANNEL and press ENTER. Use the UP and DOWN buttons to find
your desired WiFly address and press ENTER to confirm.

NOTE: Erratic fixture movement may occur if other WiFly wireless DMX products are in use in
the same area and are using the same WiFly wireless channel. When WiFly is enabled, the fixture
may immediately start to respond to the DMX wireless signal from another WiFly wireless DMX
Transceiver. Make sure to know what WiFly wireless channels are being used in the area where the
fixture is being used.

ADJ WIFLY WIRELESS TRANSCEIVER only has 0-14 wireless channels, NO CH 15.

5. Press the MENU button to exit out of the WIFLY SETTINGS submenu. Press the UP button so
that SELECT SIGNAL is highlighted and press ENTER. Press the DOWN button to highlight
WIFLY and press ENTER. Select YES and press ENTER to confirm.

6. Set your desired DMX address in the DMX ADDRESS submenu of the DMX SETTINGS main system
menu. Set your desired DMX channel mode in the DMX CH MODE submenu of the DMX SETTINGS
main system menu.

7. Repeat this process for all WiFly compatible fixtures in the WiFly wireless network, making sure
all fixtures are assigned the same WiFly wireless channel.

8. After all fixtures in the WiFly wireless network have been set to the same WiFly wireless channel
and powered ON, power ON the source WiFly DMX Transceiver device.

4. Test all fixtures connected to the WiFly wireless network to confirm proper functionality.

ADJ Products, LLC - www.adj.com - Hydro Beam X2 User Manual Page 38

Hydro Beam X2 WiFly Control

WIRELESS WIFLY INSTALLATION LOCATION GUIDELINES

Wireless DMX signal can penetrate walls, glass, metal, and most objects. However, there are many
factors that can aect and/or interrupt the wireless DMX signal, one of which is people. Therefore, it
is highly recommended to position the wireless antenna a minimum of 9.8 ft. (3m) above audiences
and/or above ground level. Careful planning and testing of the selected installation location is critical
to ensure optimum and reliable wireless DMX operation.

9.8 ft (3m)

Above Ground

ADJ Products, LLC - www.adj.com - Hydro Beam X2 User Manual Page 39

Hydro Beam X2 Error Codes

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15



Printerrormessage Description

Lamp Hot Power Off Lamp Hot Power Off

CPU-B Error CPU-B Error

CPU-C Error CPU-C Error

CPU-D Error CPU-D Error

CPU-E Error CPU-E Error

Pan Reset Error

Pan Encoder Error

Tilt Reset Error

Tilt Encoder Error

Color Reset Error Color: Reset Error

Gobo Reset Error Gobo: Reset Error

RGobo Reset Error RGobo: Reset Error

Prism1 Reset Error Prism1: Reset Error

RPrism1 Reset Error RPrism1: Reset Error

Prism2 Reset Error Prism2: Reset Error

Pan: Reset Error

Pan: Encoder Error

Tilt: Reset Error

Tilt: Encoder Error

16

17

18

19

20

21

22

23

24

25

26

27

28

29

RPrism2 Reset Error RPrism2: Reset Error

Focus Reset Error Focus: Reset Error

Base Fan 1 start Errors

Base Fan 1 stop Errors

Base Fan 1 Too Low Errors

Base Fan 1 Too High Errors

Base Fan 2 start Errors

Base Fan 2 stop Errors

Base Fan 2 Too Low Errors

Base Fan 2 Too High Errors

Base Fan 3 start Errors

Base Fan 3 stop Errors

Base Fan 3 Too Low Errors

Base Fan 3 Too High Errors

Base Fan 1 Can’t Start

Base Fan 1 Can’t Stop

Base Fan 1 speed Too low

Base Fan 1 speed Too high

Base Fan 2 Can’t Start

Base Fan 2 Can’t Stop

Base Fan 2 speed Too low

Base Fan 2 speed Too high

Base Fan 3 Can’t Start

Base Fan 3 Can’t Stop

Base Fan 3 speed Too low

Base Fan 3 speed Too high

ADJ Products, LLC - www.adj.com - Hydro Beam X2 User Manual Page 40

Hydro Beam X2 Error Codes



30

31 Side Fan 1 stop Errors

32 Side Fan 2 start Errors

33 Side Fan 2 stop Errors

34 Lamp Fan 1 start Errors

35 Lamp Fan 1 stop Errors

36 Lamp Fan 1 Too Low Errors

37 Lamp Fan 1 Too High Errors

38 Lamp Fan 2 start Errors

39 Lamp Fan 2 stop Errors

40 Lamp Fan 2 Too Low Errors

41 Lamp Fan 2 Too High Errors

42 Lamp Fan 3 start Errors

43 Lamp Fan 3 stop Errors

44 Lamp Fan 3 Too Low Errors

45 Lamp Fan 3 Too High Errors

46 Lamp Fan 4 start Errors

47 Lamp Fan 4 stop Errors

48 Lamp Fan 4 Too Low Errors

49 Lamp Fan 4 Too High Errors

50 Lamp Fan 5 start Errors

51 Lamp Fan 5 stop Errors

52 Lamp Fan 5 Too Low Errors

53 Lamp Fan 5 Too High Errors

54 Lamp Fan 6 start Errors

55 Lamp Fan 6 stop Errors

56 Lamp Fan 6 Too Low Errors

57 Lamp Fan 6 Too High Errors

58 Lamp Fan 7 start Errors

59 Lamp Fan 7 stop Errors

60 Lamp Fan 7 Too Low Errors

61 Lamp Fan 7 Too High Errors

Printerrormessage Description

Side Fan 1 start Errors

Side Fan 1 Can’t Start

Side Fan 1 Can’t Stop

Side Fan 2 Can’t Start

Side Fan 2 Can’t Stop

Lamp Fan 1 Can’t Start

Lamp Fan 1 Can’t Stop

Lamp Fan 1 speed Too low

Lamp Fan 1 speed Too high

Lamp Fan 2 Can’t Start

Lamp Fan 2 Can’t Stop

Lamp Fan 2 speed Too low

Lamp Fan 2 speed Too high

Lamp Fan 3 Can’t Start

Lamp Fan 3 Can’t Stop

Lamp Fan 3 speed Too low

Lamp Fan 3 speed Too high

Lamp Fan 4 Can’t Start

Lamp Fan 4 Can’t Stop

Lamp Fan 4 speed Too low

Lamp Fan 4 speed Too high

Lamp Fan 5 Can’t Start

Lamp Fan 5 Can’t Stop

Lamp Fan 5 speed Too low

Lamp Fan 5 speed Too high

Lamp Fan 6 Can’t Start

Lamp Fan 6 Can’t Stop

Lamp Fan 6 speed Too low

Lamp Fan 6 speed Too high

Lamp Fan 7 Can’t Start

Lamp Fan 7 Can’t Stop

Lamp Fan 7 speed Too low

Lamp Fan 7 speed Too high

ADJ Products, LLC - www.adj.com - Hydro Beam X2 User Manual Page 41

Hydro Beam X2 Dimensional Drawings

*NOT TO SCALE

14.65” / 372mm

10.4” / 264mm

21.5” / 547.2mm

14.65” / 372mm

16.5” / 419.5mm

MENU

ENTER

10.4” / 264mm

24.8” / 630mm

MENU

ENTER

15.8” / 402mm

19” / 482mm

13” / 330mm

5.5” / 140mm

5.5” / 140mm

ADJ Products, LLC - www.adj.com - Hydro Beam X2 User Manual Page 42

Hydro Beam X2 Multiple Unit Power Linking

With this feature you can connect the xtures to one another using the power cable input and

output sockets.
NOTE: USE CAUTION WHEN POWER LINKING OTHER FIXTURES AS THE POWER
CONSUMPTION OF OTHER MODEL FIXTURES MAY EXCEED THE MAX POWER OUTPUT ON
THIS FIXTURE! CHECK SILK SCREEN FOR MAX AMPS.

Hydro Beam X2 Cleaning

Due to fog residue, smoke, and dust cleaning the internal and external optical lenses must be car­ried out periodically to optimize light output.

1. Use normal glass cleaner and a soft cloth to wipe down the outside casing.

2. Clean the external optics with glass cleaner and a soft cloth every 20 days.

3. Always be sure to dry all parts completely before plugging the unit back in.
Cleaning frequency depends on the environment in which the fixture operates (i.e. smoke, fog residue,
dust, dew).

ADJ Products, LLC - www.adj.com - Hydro Beam X2 User Manual Page 43

Hydro Beam X2 Limited Warranty (USA Only)

MANUFACTURER’S LIMITED WARRANTY

A. ADJ Products, LLC hereby warrants, to the original purchaser, ADJ Products, LLC products to be free of manufacturing

defects in material and workmanship for a prescribed period from the date of purchase (see specific warranty period
on reverse). This warranty shall be valid only if the product is purchased within the United States of America, including
possessions and territories. It is the owner’s responsibility to establish the date and place of purchase by acceptable
evidence, at the time service is sought.

B. For warranty service you must obtain a Return Authorization number (RA#) before sending back the product–please

contact ADJ Products, LLC Service Department at 800-322-6337. Send the product only to the ADJ Products, LLC
factory. All shipping charges must be pre-paid. If the requested repairs or service (including parts replacement) are
within the terms of this warranty, ADJ Products, LLC will pay return shipping charges only to a designated point
within the United States. If the entire instrument is sent, it must be shipped in it’s original package. No accessories
should be shipped with the product. If any accessories are shipped with the product, ADJ Products, LLC shall
have no liability whatsoever for loss of or damage to any such accessories, nor for the safe return thereof.

C. This warranty is void if the serial number has been altered or removed; if the product is modified in any manner

which ADJ Products, LLC concludes, after inspection, affects the reliability of the product; if the product has been
repaired or serviced by anyone other than the ADJ Products, LLC factory unless prior written authorization was issued
to purchaser by ADJ Products, LLC; if the product is damaged because not properly maintained as set forth in the

instruction manual.

D. This is not a service contract, and this warranty does not include maintnance, cleaning or periodic check up.

During the period specified above, ADJ Products, LLC will replace defective parts at its expense with new or
refurbished parts, and will absorb all expenses for warranty service and repair labor by reason of defects in material or
workmanship. The sole responsibility of ADJ Products, LLC under this warranty shall be limited to the repair of the
product, or

replacement thereof, including parts, at the sole discretion of ADJ Products, LLC. All products covered by this

warranty were manufactured after August 15, 2012, and bear indentifying marks to that effect.

E. ADJ Products, LLC reserves the right to make changes in design and/or improvements upon its products without

any obligation to include these changes in any products theretofore manufactured.

No warranty, whether expressed or implied, is given or made with respect to any accessory supplied with products

described above. Except to the extent prohibited by applicable law, all implied warranties made by ADJ Products,
LLC in connection with this product, including warranties of merchantability or fitness, are limited in duration to the
warranty period set forth above. And no warranties, whether expressed or implied, including warranties of merchantability or
fitness, shall apply to this product after said period has expired. The consumer’s and/or Dealer’s sole remedy shall
be such repair or replacement as is expressly provided above; and under no circumstances shall ADJ Products,
LLC be liable for any loss or damage, direct or consequential, arising out of the use of, or inability to use, this
product.

This warranty is the only written warranty applicable to ADJ Products, LLC Products and supersedes all prior warranties

and written descriptions of warranty terms and conditions heretofore published.

MANUFACTURER’S LIMITED WARRANTY PERIODS:

• Non L.E.D. Lighting Products = 1-year (365 days) Limited Warranty (Such as: Special Effect Lighting, Intelligent
Lighting, UV lighting, Strobes, Fog Machines, Bubble Machines, Mirror Balls, Par Cans, Trussing, Lighting Stands
etc. excluding LED and lamps)

• Laser Products = 1 Year (365 Days) Limited Warranty (excluding laser diodes which have a 6 month limited
warranty)

• L.E.D. Products = 2-year (730 days) Limited Warranty (excluding batteries which have a 180 day limited warranty).

Note: 2 Year Warranty only applies to purchases within the United States.

• StarTec Series = 1 Year Limited Warranty (excluding batteries which have a 180 day limited warranty).

• ADJ DMX Controllers = 2 Year (730 Days) Limited Warranty

ADJ Products, LLC - www.adj.com - Hydro Beam X2 User Manual Page 44

Hydro Beam X2 Technical pecifications

Voltage: 100V ~ 240V/50~60Hz
IP Rating: IP65
Lamp: Osram Sirius HRI 370W LL Discharge Lamp
Color Temperature: 7800K
Power Draw: 540W
Weight: 64 lbs./ 29 kgs.
Dimensions: 15.8” (L) x 16.5” (W) x 24.8” (H)
402 x 419.5 x 630mm
Gobos: 11 Gobos + Open
Prisms: 2 Prisms (1 x 6 Facet Linear & 1 x 8 Facet Circular)
DMX Channels: 2 DMX Modes: 15 / 17
Warranty: 2 Year (730 days)

* May vary depending on several factors including but not limited to:

Enviromental Conditions, Power/Voltage, Usage Patterns (On-O Cycling), Control, and Dimming.

Please Note: Specications and improvements in the design of this unit and this
manual are subject to change without notice.

ADJ Products, LLC - www.adj.com - Hydro Beam X2 User Manual Page 45