Page 1
GALAXIAN 3D MKII
Galaxian 3D MKII General Introduction
Unpacking: Thank you for purchasing the Galaxian 3D MKII by ADJ
Products, LLC. Every Galaxian 3D MKII has been thoroughly tested
and has been shipped in perfect operating condition. Carefully check
the shipping carton for damage that may have occurred during shipping. If the carton appears to be damaged, carefully inspect your xture for any damage and be sure all equipment necessary to operate
the unit has arrived intact. In the event damage has been found or parts
are missing, please contact our toll free customer support number for
further instructions. Please do not return this unit to your dealer with-
out contacting customer support rst.
Introduction: The Galaxian 3D MKII is an incredible five channel
DMX intelligent, green and red laser fixture. The red and green laser
beams rotate back and forth creating amazing aerial effect on a ceiling
or wall. The Galaxian 3D MKII can operate as a stand alone fixture, or
in a Master/Slave configuration. The Galaxian 3D MKII can be a sound
active fixture or it can also be controlled via DMX. This fixture is suitable for theaters, studios, retail stores, and other similar locations. For
best results use fog or special effects smoke to enhance the beams
projections.
Customer Support: ADJ Products, LLC provides a toll free cus-
tomer support line, to provide set up help and to answer any question
should you encounter problems during your set up or initial operation.
You may also visit us on the web at www.adj.com for any comments
or suggestions. For service related issue please contact ADJ Products,
LLC. Service Hours are Monday through Friday 8:00 a.m. to 4:30 p.m.
Pacic Standard Time.
Voice: (800) 322-6337
Fax: (323) 582-2941
E-mail: support@americandj.com
3/13
User Instructions
Warning! To prevent or reduce the risk of electrical shock or re, do
not expose this unit to rain or moisture.
Caution! There are no user serviceable parts inside this unit. Do not
attempt any repairs yourself, doing so will void your manufactures warranty. In the unlikely event your unit may require service please contact
ADJ customer support.
PLEASE recycle the shipping carton whenever possible.
ADJ Products, LLC - www.adj.com - Galaxian 3D MKII Instruction Manual Page 2
Page 2
Galaxian 3D MKII General Instructions Galaxian 3D MKII Safety Precautions
!
!
Please carefully read and understand the instructions in this manual
thoroughly before attempting to operate this unit. These instructions
contain important safety information regarding the use and maintenance of this unit. Please keep this manual with the unit, for future
reference.
CAUTION IMPORTANT! When installing this projector, make sure
that it is mounted in a manner that prevents the audience from
looking directly into the beam, and the beam from striking the
audience.
Galaxian 3D MKII Features
• 30mW Green Laser & 80mW Red Laser
• 5 Channel DMX Control
• 2 Operating Modes - Sound Active & DMX Control
• Fan Cooled
• Digital Display for Address and Function Setting
• UC3 Controller (Not Included)
• Power Cord Daisy Chain up to 14 units max. See page 16
Galaxian 3D MKII Warranty Registration
The Galaxian 3D MKII carries a 90 day limited warranty. Please fill out
the enclosed warranty card to validate your purchase. All returned
service items whether under warranty or not, must be freight prepaid and accompany a return authorization (R.A.) number. If the unit
is under warranty you must provide a copy of your proof of purchase
invoice. Please contact ADJ customer support for a R.A. number.
Galaxian 3D MKII Installation
The unit should be mounted using a mounting clamp (not provided),
axing it to the mounting bracket that is provided with the unit.
Always ensure that the unit is rmly xed to avoid vibration and slip-
ping while operating. Always ensure that the structure to which you
are attaching the unit is secure and is able to support a weight of 10
times the unit’s weight. Also, always use a safety cable that can hold
12 times the weight of the unit when installing the xture.
The equipment must be installed by a professional, and it must be
installed in a place where it is out of the reach of people’s grasp.
Safety Issues: This unit may “pop” the fuse if the maximum allotted
load of 7 amps is reached.
• To reduce the risk of electrical shock or re, do not expose this unit
rain or moisture.
• Do not spill water or other liquids into or on to your unit.
• Do not attempt to remove or break o the ground prong from the
electrical cord. This prong is used to reduce the risk of electrical
shock and re in case of an internal short. Do not attempt to oper-
ate this unit if the power cord has been frayed or broken.
• Disconnect from main power before making any type of connection.
• Do not remove the cover under any conditions. There are no user
serviceable parts inside.
• Always be sure to mount this unit in an area that will allow proper
ventilation. Allow about 6” (15cm) between this device and a wall.
• Do not attempt to operate this unit, if it becomes damaged.
• This unit is intended for indoor use only, use of this product out-
doors voids all warranties.
• During long periods of non-use, disconnect the unit’s main power.
• Always mount this unit in safe and stable matter.
• Power cords should be routed so they are not likely to be walked
on, pinched by items placed upon or against them.
• Cleaning -The fixture should be cleaned only as recommended by
the manufacturer. See page 18 for cleaning details.
• Heat -The appliance should be situated away from heat sources
such as radiators, heat registers, stoves, or other appliances
(including amplifiers) that produce heat.
• The fixture should be serviced by qualified service personnel when:
A. The power-supply cord or the plug has been damaged.
B. Objects have fallen, or liquid has been spilled into the unit.
C. The unit has been exposed to rain or water.
D. The unit does not appear to operate normally or exhibits a
marked change in performance.
ADJ Products, LLC - www.adj.com - Galaxian 3D MKII Instruction Manual Page 4ADJ Products, LLC - www.adj.com - Galaxian 3D MKII Instruction Manual Page 3
DANGER
VISIBLE LASER RADIATION
-AVOID DIRECT EYE EXPOSURE
LASER DIODE
WAVELENGTH : 635~650 nm
Max Output : <4.9mW
Class IIIa Laser Product
Page 3
Galaxian 3D MKII Laser Warnings and Safety
NON-INTERLOCKED HOUSING WARNING
The Galaxian 3D MKII contains high power laser devices internally.
Do not open the laser housing, due to the potential exposure to
unsafe levels of laser radiation. The laser power levels, if the unit is
opened, can cause instant blindness, skin burns and res.
Galaxian 3D MKII Laser Warnings and Safety
After setting up, and before public use, test laser to ensure proper
function. Do not use if any defect is detected. Do not use if laser
emits only one or two laser beams rather than dozens/hundreds, as
this could indicate damage to the diraction grating optic, and could
allow emission of higher laser levels above Class 3R.
STOP AND READ ALL LASER SAFETY DATA
OPERATION INSTRUCTIONS AND LASER SAFETY
The light source emitted from this product can potentially cause eye
injury if not set up and used properly. The light source emitted from a
laser is very dierent from any other light sources with which you may
be aware of. Laser light is thousands of times more concentrated
than any light from any other kind of light source. This concentration
of light can cause instant eye injuries, primarily by burning the retina
(the back of your eyeball contatining cells that are sensitive to light).
Even if you cannot feel “heat” from a laser beam, it can still potentially injure or blind you or your audience. Even very small amounts
of laser beam light are potentially hazardous even at long distances.
Laser eye injuries can be sustained faster than you can blink.
Do not think that because this laser splits the laser beam into hundreds of beams and that the laser beam is scanned out in high
speed, that an individual laser beam is safe for eye exposure. This
laser uses dozens of milliwatts of laser power (Class 3B levels inter-
nally) before it splits into multiple beams (Class 3R levels). Many of
the individual beams are potentially hazardous to the eyes.
Do not that because the laser light is moving, it is safe. This is not
true. Nor, do the laser beams always move. Since eye injuries can
occur instantly, it is critical to prevent even the smallest possibility of
any direct eye exposure. In the laser safety regulation, it is not legal
to aim Class 3R lasers in areas which people can get exposed. This
is true even if it is aimed below people’s faces, such as on a dance
oor.
Do not operate the laser without rst reading and understanding
all safety and technical data in this manual.
Always set up and install all laser eects so that all laser light is at
least 3 meters (9.8 feet) above the oor on which people can stand.
ADJ Products, LLC - www.adj.com - Galaxian 3D MKII Instruction Manual Page 5
Do not point lasers at people or animals. Never look into the laser
aperture or laser beams.
Do not point lasers in areas in which people can potentially get
exposed, such as uncontrolled balconies, etc.
Do not point lasers at highly reective surfaces, such as windows,
mirrors and shiny metal. Even laser reections can be hazardous.
Never point a laser at aircraft, this is a federal oense.
Never point un-terminated laser beams into the sky.
Do not expose the output optic (aperture) to cleaning chemicals.
Do not use laser if the laser appears to be emitting only one or two
beams.
Do not use the laser if the housing is damaged, the housing is open,
or if the optics appear damaged in any way.
Never open the laser housing. The high laser power levels inside of
the protective housing can start res, burn skin and will cause instant
eye injury.
Never leave this device running unattended.
The operation of a class 3R laser show is only allowed if the show
is controlled by a skilled and well- trained operator, familiar with the
data included in this manual.
The legal requirements for using laser entertainment products vary
from country to country. The user is responsible for the legal requirements at the location/country of use.
Always use proper lighting safety cables when hanging lights and
eects overhead.
ADJ Products, LLC - www.adj.com - Galaxian 3D MKII Instruction Manual Page 6
Page 4
Galaxian 3D MKII Laser Warning Labels
Galaxian 3D MKII Set Up
LASER RADI ATION
IS EMITTED F ROM
THIS APERT URE
AVOID E XPOSU RE
ADJ Products, LLC
6122 S.Eastern Ave.
Los Angeles. CA 90040 USA
Manufactured:
LASER RADIATION AVOID
DIRECT EYE EXPOSURE
Maximum output <5 mW
Wavelength 532nm & 635nm
Class IIIa laser product
This device complies with 21 CFR chapter l,
Subchapter J, CFR 1040.10 and 1040.11
Specification stickers
CAUTION - CLASS 3R
LASER RADIATION WHEN OPEN
AVOID DIRECT EYE EXPOSURE
LASER RADI ATION
IS EMITTED F ROM
THIS APERT URE
AVOID E XPOSU RE
40mm
40mm
17mm
41 mm
LASER RADIATION AVOID
DIRECT EYE EXPOSURE
Maximum output <5 mW
Wavelength 532nm & 635nm
Class IIIa laser product
This device complies with 21 CFR chapter l,
Subchapter J, CFR 1040.10 and 1040.11
40mm
CAUTION - CLASS 3R
LASER RADIATION WHEN OPEN
AVOID DIRECT EYE EXPOSURE
12mm
Specification stickers
20mm
Power Supply: Before plugging your unit in, be sure the source volt-
age in your area matches the required voltage for your ADJ Galaxian 3D MKII. The ADJ Galaxian 3D MKII voltage is user selectable.
Because line voltage may vary from venue to venue, you should be
sure your unit voltage matches the wall outlet voltage before attempt-
ing to operate you xture.
DMX-512: DMX is short for Digital Multiplex. This is a universal pro-
tocol used by most lighting and controller manufactures as a form of
communication between intelligent fixtures and controllers. A DMX
30 mm
controller sends DMX data instructions from the controller to the fixture. DMX data is sent as serial data that travels from fixture to fixture
via the DATA “IN” and DATA “OUT” XLR terminals located on all DMX
fixtures (most controllers only have a DATA “OUT” terminal).
DMX Linking: DMX is a language allowing all makes and models of
dierent manufactures to be linked together and operate from a single controller, as long as all xtures and the controller are DMX com-
pliant. To ensure proper DMX data transmission, when using several
DMX fixtures try to use the shortest cable path possible. The order
in which fixtures are connected in a DMX line does not influence the
DMX addressing. For example; a fixture assigned a DMX address of 1
may be placed anywhere in a DMX line, at the beginning, at the end,
or anywhere in the middle. Therefore, the first fixture controlled by the
controller could be the last fixture in the chain. When a fixture is assigned a DMX address of 1, the DMX controller knows to send DATA
assigned to address 1 to that unit, no matter where it is located in the
DMX chain.
Data Cable (DMX Cable) Requirements (For DMX and Master/Slave
Operation): The Galaxian 3D MKII can be con-
trolled via DMX-512 protocol. The Galaxian 3D
MKII is a ve channel DMX unit. The DMX address
is set electronically using the controls on the top
rear panel of the unit. Your unit and your DMX controller require a approved DMX-512 110 Ohm Data
cable for data input and data output (Figure 1). We
recommend Accu-Cable DMX cables. If you are
making your own cables, be sure to use standard
Figure 1
110-120 Ohm shielded cable (This cable may be purchased at almost
ADJ Products, LLC - www.adj.com - Galaxian 3D MKII Instruction Manual Page 8ADJ Products, LLC - www.adj.com - Galaxian 3D MKII Instruction Manual Page 7
Page 5
Galaxian 3D MKII Set Up Galaxian 3D MKII Set Up
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
DMX512
DMX+,DMX-,COMMON
1
2
3
Termination reduces signal errors and
avoids signal transmission problems
and interference. It is always advisable
to connect a DMX terminal, (Resistance
120 Ohm 1/4 W) between PIN 2 (DMX-)
and PIN 3 (DMX +) of the last fixture.
POWER
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
all professional sound and lighting stores). Your cables should be made
with a male and female XLR connector on either end of the cable. Also
remember that DMX cable must be daisy chained and cannot be split.
Notice: Be sure to follow gures two and three when making your own
cables. Do not use the ground lug on the XLR connector. Do not connect the cable’s shield conductor to the ground lug or allow the shield
conductor to come in contact with the XLR’s outer casing. Grounding
the shield could cause a short circuit and erratic behavior.
COMMON
1
DMX512 IN
3
3-PIN XLR
2
Figure 2
XLR Pin Conguration
Pin 1 = Ground
Pin 2 = Data Compliment (negative)
Pin 3 = Data True (positive)
XLR Male Socket
1 Ground
Figure 3
DMX512 OUT
3-PIN XLR
2 Cold
3 Hot
1
3
2
XLR Female Socket
2 Cold
DMX +
DMX -
1 Ground
3 Hot
5-Pin XLR DMX Connectors.
Some manufactures use 5-pin DMX-
512 data cables for DATA transmission in place of 3-pin. 5-pin DMX
xtures may be implemented in a 3-pin DMX line. When inserting standard 5-pin data cables in to a 3-pin line a cable adaptor must be used,
these adaptors are readily available at most electric stores. The chart
below details a proper cable conversion.
3-Pin XLR to 5-Pin XLR Conversion
Conductor 5-Pin XLR Male (In)3-Pin XLR Female (Out)
Ground/Shield
Data Compliment (- signal)
Data True (+ signal)
Not Used
Not Used
Pin 1
Pin 2
Pin 3
Pin 1
Pin 2
Pin 3
Pin 4 - Do Not Use
Pin 5 - Do Not Use
Special Note: Line Termination.
When longer runs of cable are
used, you may need to use a terminator on the last unit to avoid erratic
behavior. A terminator is a 110-120 ohm 1/4 watt resistor which is con-
nected between pins 2 and 3 of a male XLR connector (DATA + and
DATA -). This unit is inserted in the female XLR connector of the last
unit in your daisy chain to terminate the line. Using a cable terminator
(ADJ part number Z-DMX/T) will decrease the possibilities of erratic
behavior.
ADJ Products, LLC - www.adj.com - Galaxian 3D MKII Instruction Manual Page 9 ADJ Products, LLC - www.adj.com - Galaxian 3D MKII Instruction Manual Page 10
Termination reduces signal errors and
1
avoids signal transmission problems
3
and interference. It is always advisable
2
to connect a DMX terminal, (Resistance
120 Ohm 1/4 W) between PIN 2 (DMX-)
and PIN 3 (DMX +) of the last fixture.
Figure 4
Page 6
Galaxian 3D MKII System Menu Galaxian 3D MKII System Menu Chart
System Menu: When conrming your setting press ENTER
and then hold MENU for at least 2-3 seconds, or you can
wait 1 minute for automatic setup. To exit without making
any adjustments press the MENU button.
ADDR - DMX Address Setting.
1. Tap the either the MENU, UP, or DOWN buttons until “ADDR”
is displayed, press ENTER.
2. The current address will now be displayed and ashing.
Press the UP or DOWN buttons to nd your desired address.
Press ENTER to set your desired DMX address.
SLND - This will let you set unit as a master or slave in
a master/slave conguration.
1. Tap the MENU button until “SLND” is displayed, press
ENTER. Either “SL 1” or “SL 2” will be displayed.
2. Tap the UP or DOWN buttons until your desired setting is
displayed, press ENTER and then hold MENU for at least 2-3
seconds to conm.
NOTE: In a Master/Slave conguration you can make one
xture the Master and then set the next xture to “SL 2”, the
xtures will now have contrast movement to each other.
SOUN - Sound Active mode.
1. Tap the MENU button until “SOUN” is displayed, press
ENTER.
2. The display will show either “ON” or “OFF”. Press the UP or
DOWN buttons to select “ON” to activate sound active mode,
or “OFF” to deactivate sound active mode.
3. Press ENTER and then hold MENU for at least 2-3 seconds
to conm.
ADJ Products, LLC - www.adj.com - Galaxian 3D MKII Instruction Manual Page 12ADJ Products, LLC - www.adj.com - Galaxian 3D MKII Instruction Manual Page 11
Page 7
Galaxian 3D MKII System Menu Galaxian 3D MKII System Menu
DNST - This mode can be used as a precaution mode, that
in case the DMX signal is lost, the operating mode chosen
in the setup is the running mode the xture will go into when
the DMX signal is lost. You can also set this as the operat-
ing mode you would like the unit to return to when power is
applied.
1. Press the MENU button until “DNST” is displayed, press
ENTER.
2. Either “MAST”, “BLND”, or “LAST” will be displayed. Choose
an operating mode you would like the unit to start up in when
power is applied or the DMX signal is lost.
• MAST (Master Slave) - If the DMX signal is lost or power is
applied, the unit will automatically go into Master Slave mode.
• BLND (Blackout) - If the DMX signal is lost or power is applied,
the unit will automatically go into stand by mode.
• LAST (Last State) - If the DMX signal is lost the xture will stay
in the last DMX set up. If power is applied and this mode is set,
the unit will automatically go into the last DMX set up.
DISP - This function will “ip” the LED display 180º.
1. Press the MENU button until “DISP” is displayed, press ENTER.
2. Either “dISP” or “dSIP” will now be displayed. Press the UP or
DOWN buttons to select one or the other.
3. Press ENTER, and then press and hold the MENU button for at least
three seconds to conrm.
TEST - This function will run a self test program.
1. Press the MENU button until “TEST” is displayed, press ENTER.
2. The unit will now run a self test. Press the MENU button to exit.
FHRS - With this function you can display the running
time of the xture.
1. Tap the MENU button until “FHRS” is displayed, press
ENTER.
2. The display shows the running time of the unit. Press MENU
to exit.
3. Press ENTER to conrm your desired set up.
LED - With this function you can have the LED display
turn off after 10 seconds.
1. Tap the MENU button until “LED” is displayed, press ENTER.
2. The display will show either “ON” or “OFF”. Press the UP or
DOWN buttons to select “ON” to keep the LED display on at
all times, or “OFF” to switch to have the LED display switch o
after 10 seconds.
3. Press ENTER and then hold MENU for at least 2-3 seconds
to conm.
VER - This will display the software version.
1. Press the MENU button until “VER” is displayed. Press the ENTER
button and the software vesion will be displayed.
2. Press the MENU button to leave this function.
RSET - Use this function to reset the unit.
1. Tap the MENU button until “RSET” is displayed, press ENTER.
2. The xture will now reset.
ADJ Products, LLC - www.adj.com - Galaxian 3D MKII Instruction Manual Page 14ADJ Products, LLC - www.adj.com - Galaxian 3D MKII Instruction Manual Page 13
Page 8
Galaxian 3D MKII Operation
Galaxian 3D MKII Operation
CAUTION IMPORTANT! When installing this projector, make sure
that it is mounted in a manner that prevents the audience from
looking directly into the beam, and the beam from striking the
audience.
Operating Modes: The Galaxian 3D MKII has two different operating modes.
Universal DMX Control: This function allows you to use a Elation®
universal DMX-512 controller to control the chases and patterns,
dimmer and strobe. A DMX controller allows you to create unique
programs tailored to your individual needs.
1. The Galaxian 3D MKII is a five DMX channel DMX fixture. See
page 17 for detailed description of the DMX values and traits.
2. To control your fixture in DMX mode, follow the set-up procedures
on pages 8-10 as well as the set-up specifications that are includ ed with your DMX controller.
3. Use the controller’s faders to control the various DMX fixture traits.
4. This will allow you to create your own programs.
5. Follow the instruction on page 12 to set the DMX address.
6. For longer cable runs (more than a 100 feet) use a terminator on
the last fixture.
7. For help operating in DMX mode consult the manual included
with your DMX controller.
er via the XLR connector on the rear of the units. Remember the
Male XLR connector is the input and the Female XLR connector
is the output. The rst unit in the chain (master) will use the female
XLR connector only - The last unit in the chain will use the male
XLR connector only. For longer cable runs we suggest a termina-
tor at the last fixture.
2. On the Master unit find your desired show and set that show by
pressing the ENTER button.
3. On the slave units tap the MENU button until “SLND” is dis-
played, and Press ENTER. Choose either “SL 1” or “SL 2” and
press ENTER. Please see page 12 for more info.
4. The slave units will now follow the Master unit.
Galaxian 3D MKII Power Cord Daisy Chain
With this feature you can connect the xtures to one another
using the IEC input and output sockets. The quantity that can be
connected is 14 xtures maximum. After 14 xtures you will need
to use a new power outlet. They must be the same xtures. DO
NOT mix xtures.
Sound Active Mode: This mode allows either single unit or several
Galaxian 3D MKII UC3 Control
units linked together, to run to the beat of the music.
1. Tap the MENU button until “SOUN” is displayed, and press
ENTER.
2. Tap the UP or DOWN buttons so that “ON” is displayed, and
press ENTER and then hold MENU for at least 2-3 seconds.
3. The optional UC3 Controller (not included) may be used to con trol different functions including blackout.
Master-Slave Operation This function will allow you to link up to 16
Stand By Blackout the fixture
Function 1. Strobe Red
2. Strobe Green
3. Strobe in Green/Red
Mode Sound (LED OFF) Speed(LED ON)
Chase Speed
1-3
units together and operate without a controller. The units will be sound
activated. In Master-Slave operation one unit will act as the controlling
unit and the others will react to the controlling units programs. Any unit
can act as a Master or as a Slave.
1. Using approved DMX data cables, daisy chain your units togeth-
ADJ Products, LLC - www.adj.com - Galaxian 3D MKII Instruction Manual Page 15 ADJ Products, LLC - www.adj.com - Galaxian 3D MKII Instruction Manual Page 16
Page 9
Galaxian 3D MKII DMX Traits
Channel Value Function
1 RED LASER
0 - 7 OFF
8 - 15 ON
16 - 239 STROBING SLOW - FAST
240 - 247 SOUND ACTIVE
248 - 255 ON
2 GREEN LASER
0 - 7 OFF
8 - 15 ON
16 - 239 STROBING SLOW - FAST
240 - 247 SOUND ACTIVE
248 - 255 ON
3 LASER ROTATION 1
0 - 127 0° - 360°
128 - 189 COUNTER - CLOCKWISE FAST - SLOW
190 - 193 NO ROTATION
194 - 255 CLOCKWISE SLOW - FAST
4 LASER ROTATION 2
0 - 127 0° - 360°
128 - 189 COUNTER - CLOCKWISE FAST - SLOW
190 - 193 NO ROTATION
194 - 255 CLOCKWISE SLOW - FAST
5 MACROS
0 - 7 NO FUNCTION
8 - 23 MACRO 1
24 - 39 MACRO 2
40 - 55 MACRO 3
56 - 71 MACRO 4
72 - 87 MACRO 5
88 - 103 MACRO 6
104 - 119 MACRO 7
120 - 135 MACRO 8
136 - 151 MACRO 9
152 - 167 MACRO 10
168 - 183 MACRO 11
184 - 199 MACRO 12
200 - 215 MACRO 13
216 - 231 MACRO 14
232 - 247 MACRO 15
248 - 255 SOUND ACTIVE
Galaxian 3D MKII Fuse Replacement
Locate and remove the unit’s power cord. Once the cord has been
removed located the fuse holder located inside the power socket.
Insert a flat-head screw driver into the power socket and gently pry
out the fuse holder. Remove the bad fuse and replace with a new one.
The fuse holder has a built-in socket for a spare fuse be sure not to
confuse the spare fuse with active fuse.
Galaxian 3D MKII Cleaning
Fixture Cleaning: Due to fog residue, smoke, and dust cleaning
the internal and external lenses should be carried out periodically to
optimize light output.
1. Use normal glass cleaner and a soft cloth to wipe down the out side casing.
2. Clean the external optics with glass cleaner and a soft cloth every
20 days.
3. Always be sure to dry all parts completely before plugging the
unit back in.
Cleaning frequency depends on the environment in which the fixture
operates (I.e. smoke, fog residue, dust, dew). In heavy use we recommend cleaning on a monthly basis. Periodic cleaning will ensure longevity, and crisp beam output.
Galaxian 3D MKII Trouble Shooting
Trouble Shooting: Listed below are a few common problems that
you may encounter, with solutions.
No output from the unit;
1. Be sure the external fuse has not blown. The fuse is located on
the rear panel of the unit.
2. Be sure the fuse holder is completely and properly seated.
Unit does not respond to sound;
1. Low frequencies (bass) should cause the unit to react to sound.
Tapping on the microphone, quiet or high pitched sounds may
not activate the unit.
ADJ Products, LLC - www.adj.com - Galaxian 3D MKII Instruction Manual Page 17
ADJ Products, LLC - www.adj.com - Galaxian 3D MKII Instruction Manual Page 18
Page 10
Galaxian 3D MKII Warranty
MANUFACTURER’S LIMITED WARRANTY
A. ADJ Products, LLC hereby warrants, to the original purchaser, ADJ Products, LLC products
to be free of manufacturing defects in material and workmanship for a prescribed period from
the date of purchase (see specific warranty period on reverse). This warranty shall be valid only if the
product is purchased within the United States of America, including possessions and
territories. It is the owner’s responsibility to establish the date and place of purchase by acceptable
evidence, at the time service is sought.
B. For warranty service you must obtain a Return Authorization number (RA#)
before sending back the product–please contact ADJ Products, LLC Service Department
at 800-322-6337. Send the product only to the ADJ Products, LLC factory. All
shipping charges must be pre-paid. If the requested repairs or service (including
parts replacement) are within the terms of this warranty, ADJ Products, LLC will pay return
shipping charges only to a designated point within the United States. If the entire instrument is
sent, it must be shipped in it’s original package. No accessories should be shipped with the product. If
any accessories are shipped with the product, ADJ Products, LLC shall have no liability whatsoever for
loss of or damage to any such accessories, nor for the safe return thereof.
C. This warranty is void if the serial number has been altered or removed; if the product is modified in any
manner which ADJ Products, LLC concludes, after inspection, affects the reliability of the product; if the
product has been repaired or serviced by anyone other than the ADJ Products, LLC factory unless prior
written authorization was issued to purchaser by ADJ Products, LLC; if the product is damaged because
not properly maintained as set forth in the instruction manual.
D. This is not a service contract, and this warranty does not include maintnance, cleaning or periodic check
up. During the period specified above, ADJ Products, LLC will replace defective parts at its expense
with new or refurbished parts, and will absorb all expenses for warranty service and repair labor by
reason of defects in material or workmanship. The sole responsibility of ADJ Products, LLC under this
warranty shall be limited to the repair of the product, or replacement thereof, including parts, at the sole
discretion of ADJ Products, LLC. All products covered by this warranty were manufactured after August
15, 2012, and bear indentifying marks to that effect.
E. ADJ Products, LLC reserves the right to make changes in design and/or improvements upon its products
without any obligation to include these changes in any products theretofore manufactured.
Galaxian 3D MKII Specifications
Model: Galaxian 3D MKII
Voltage: 120V 60Hz or 230V 50Hz
Power Consumption: 22.5W
Power Cord Daisy Chain: 14 Fixtures Max.
Lasers: 30mW Green Diode
80mW Red Diode
Colors: Red & Green
Beam Angle: 90 Degrees
Dimensions: 8.75”(L) x 7.75”(W) x 3.25”(H)
221mm x 194mm x 78mm
Weight: 7 Lbs. / 3 kgs.
Fuse: 6.3 Amp
Duty Cycle: None
DMX: 5 DMX Channels
Sound Active: Ye s
Working Position: Any Safe, Secure Position
Warranty: 90 Days
Please Note: Specications and improvements in the design
of this unit and this manual are subject to change without any
prior written notice.
No warranty, whether expressed or implied, is given or made with respect to any accessory supplied with
products described above. Except to the extent prohibited by applicable law, all implied warranties made
by ADJ Products, LLC in connection with this product, including warranties of merchantability or fitness,
are limited in duration to the warranty period set forth above. And no warranties, whether expressed or
implied, including warranties of merchantability or fitness, shall apply to this product after said period
has expired. The consumer’s and/or Dealer’s sole remedy shall be such repair or replacement as is
expressly provided above; and under no circumstances shall ADJ Products, LLC be liable for any loss or
damage, direct or consequential, arising out of the use of, or inability to use, this product.
This warranty is the only written warranty applicable to ADJ Products, LLC Products and
supersedes all prior warranties and written descriptions of warranty terms and conditions heretofore
published.
MANUFACTURER’S LIMITED WARRANTY PERIODS:
•LightingProducts=1-year(365days)LimitedWarranty(Such as: Special Effect Lighting, Intelligent
Lighting, UV lighting, Strobes, Fog Machines, Bubble Machines, Mirror Balls, Par Cans, Trussing,
Lighting Stands etc. excluding LED and lamps)
•LaserProducts=90-DayLimitedWarranty
•L.E.D.Products=3-year(1095days)LimitedWarranty(excluding motors, PCB boards, and power
supplies, which have a 1-year (365 day Limited Warranty) and batteries which have a 180 day
limited warranty). Only the L.E.D.s carry a 3-year warranty
ADJ Products, LLC - www.adj.com - Galaxian 3D MKII Instruction Manual Page 19
ADJ Products, LLC
6122 S. Eastern Ave. Los Angeles, CA 90040 USA
Tel: 323-582-2650 / Fax: 323-725-6100
Web: www.adj.com / E-mail: info@adj.com
A.D.J. Supply Europe B.V.
Junostraat 2
6468 EW Kerkrade
Netherlands
service@adj.eu / www.adj.com
Tel: +31 45 546 85 00 / Fax: +31 45 546 85 99
Loading...