ADJ Focus Wash 400 User guide

FOCUS WASH 400

US SKU#: FOC615
EU SKU#: 1237000240
ITF-14#: 818651029130

User Manual

©2022 ADJ Products, LLC all rights reserved. Information, specications, diagrams, images, and

instructions herein are subject to change without notice. ADJ Products, LLC logo and identifying
product names and numbers herein are trademarks of ADJ Products, LLC. Copyright protection
claimed includes all forms and matters of copyrightable materials and information now allowed by
statutory or judicial law or hereinafter granted. Product names used in this document may be trade­marks or registered trademarks of their respective companies and are hereby acknowledged. All
non-ADJ Products, LLC brands and product names are trademarks or registered trademarks of their
respective companies.

ADJ Products, LLC and all aliated companies hereby disclaim any and all liabilities for property,

equipment, building, and electrical damages, injuries to any persons, and direct or indirect economic
loss associated with the use or reliance of any information contained within this document, and/or as
a result of the improper, unsafe, insucient and negligent assembly, installation, rigging, and opera­tion of this product.

DOCUMENT VERSION

Due to additional product features and/or enhancements, an updated version of
this document may be available online.
Please check www.adj.com for the latest revision/update of this manual
before beginning installation and/or programming.

Date

05/05/2021 1.0 1.1.1 16 / 21 / 23 ch Initial Release

06/25/2021 2.0 1.1.2

08/09/2021 3.0 N/C No Change Updated Dimensional Drawings

08/25/2021 4.0 N/C No Change Corrected DMX Traits

08/31/2021 5.0 N/C No Change

01/27/2022 6.0 1.1.4 No Change Updated System Menu, DMX Traits

Document

Version

Software

Version

DMX Channels Notes

17 / 22 / 24 / CMY 18

/ CMY 24 ch

Update DMX Traits, System Menu,
added Color Swatch Table, add
Snoot and Linear Lens Installation

Updated Color Macros Chart and
Specifications

Europe Energy Saving Notice
Energy Saving Matters (EuP 2009/125/EC)

Saving electric energy is a key to help protecting the enviroment. Please turn o all electrical products when

they are not in use. To avoid power consumption in idle mode, disconnect all electrical equipment from power
when not in use. Thank you!

ADJ Products, LLC - www.adj.com - Focus Wash 400 User Manual Page 2

TABLE OF CONTENTS

General Information 4

Key Features | Warranty Returns 5

Limited Warranty (USA Only) 6

Safety Guidelines 7

Overview 8

DMX Set Up 9

Installation 11

Control Panel 17

System Menu 18

DMX Addressing 22

DMX Traits 23

Color Macros Chart 30

Virtual Swatch Colors 32

Color Temperature Chart 33

Dimmer Modes & Curves 34

Cleaning & Maintenance 35

Fuse Replacement | Software Updates 36

Dimensional Drawings 37

Specifications 38

ADJ Products, LLC - www.adj.com - Focus Wash 400 User Manual Page 3

GENERAL INFORMATION

Introduction: Congratulations on your purchase of the ADJ Focus Wash 400! This device is a 400W,

RGBACL (Red, Green, Blue, Amber, Cyan, Lime), LED moving light wash, and has been designed to
perform reliably for years when the guidelines in this booklet are followed. Please read and understand
the instructions in this manual carefully and thoroughly before attempting to operate this device. These
instructions contain important information regarding safety during use and maintenance.

Please keep this manual with the device for future reference.

Customer Support: Contact ADJ Service for any product related service and support needs. Also visit

forums.adj.com with questions, comments or suggestions.

Parts: To purchase parts online visit:

http://parts.adj.com (US)
http://www.adjparts.eu (EU)

ADJ SERVICE USA - Monday - Friday 8:00am to 4:30pm PST
Voice: 800-322-6337 | Fax: [phone] | [e-mail]

ADJ SERVICE EUROPE - Monday - Friday 08:30 to 17:00 CET
Voice: [phone] | Fax: [phone] | [e-mail]

ADJ PRODUCTS LLC USA

6122 S. Eastern Ave. Los Angeles, CA. 90040
323-582-2650 | Fax [phone] | www.adj.com | [e-mail]

ADJ SUPPLY Europe B.V

Junostraat 2 6468 EW Kerkrade, The Netherlands
[phone] | Fax [phone]

www.adj.eu | [e-mail]

ADJ PRODUCTS GROUP Mexico

AV Santa Ana 30 Parque Industrial Lerma, Lerma, Mexico 52000
[phone]

WARNING! To prevent or reduce the risk of electrical shock or re, do not expose this unit to rain or

moisture.

CAUTION! There are no user serviceable parts inside this unit. Do not attempt any repairs yourself,
doing so will void your manufacturer’s warranty. In the unlikely event your unit may require service,
please contact ADJ Products, LLC.

Do not discard the shipping cartoon in the trash. Please recycle when ever possible.

ADJ Products, LLC - www.adj.com - Focus Wash 400 User Manual Page 4

KEY FEATURES

• 400W RGBACL LED

• 10 to 46-degree motorized zoom

• Flicker free operation for TV and film

• 16-bit pan/tilt movement

• RGBACL color mixing

• Variable dimming modes/curves and strobe effects

• DMX and RDM protocol support

• DMX and power in/out connections

• LCD menu display with 6 button control panel

• Multiple unit power linking

• Multi-voltage universal auto switching power supply (AC100-240V)

INCLUDED ITEMS:

• Twist-lock power cable (x1)

• Omega brackets (x2)

• Snoot (x1)

• Linear Lens (x1)

• Screws (x4)

WARRANTY RETURNS

All returned service items, whether under warranty or not, must be freight pre-paid and accompanied
by a return authorization (R.A.) number. The R.A. number must be clearly written on the outside of the
return package. A brief description of the problem as well as the R.A. number must also be written
down on a piece of paper included in the shipping carton. If the unit is under warranty, you must pro­vide a copy of your proof of purchase invoice. You may obtain an R.A. number by contacting our cus­tomer support team. All packages returned to the service department not displaying an R.A. number
on the outside of the package will be returned to the shipper.

ADJ Products, LLC - www.adj.com - Focus Wash 400 User Manual Page 5

LIMITED WARRANTY (USA ONLY)

A. ADJ Products, LLC hereby warrants, to the original purchaser, ADJ Products, LLC products to be free of

manufacturing defects in material and workmanship for a prescribed period from the date of purchase

(see specic warranty period on reverse). This warranty shall be valid only if the product is purchased

within the United States of America, including possessions and territories. It is the owner’s responsibility
to establish the date and place of purchase by acceptable evidence, at the time service is sought.

B. For warranty service, you must obtain a Return Authorization number (RA#) before sending the product

back—please contact ADJ Products, LLC Service Department at 800-322-6337. Send the product only to
the ADJ Products, LLC factory. All shipping charges must be prepaid. If the requested repairs or service
(including parts replacement) are within the terms of this warranty, ADJ Products, LLC will pay return ship­ping charges only to a designated point within the United States. If the entire instrument is sent, it must be
shipped in its original package and packaging material. No accessories should be shipped with the prod­uct. If any accessories are shipped with the product, ADJ Products, LLC shall incur no liability whatsoever
for loss of or damage to any such accessories, nor for the safe return thereof.

C. This warranty is void if the product serial number and/or labels are altered or removed; if the product is

modied in any manner which ADJ Products, LLC concludes, after inspection, aects the reliability of the

product; if the product has been repaired or serviced by anyone other than the ADJ Products, LLC factory
unless prior written authorization was issued to purchaser by ADJ Products, LLC; if the product is dam­aged because it was not properly maintained as set forth in the product instructions, guidelines and/or
user manual.

D. This is not a service contract, and this warranty does not include maintenance, cleaning, or periodic

checkup. During the period specied above, ADJ Products, LLC will replace defective parts at its expense

with new or refurbished parts, and will absorb all expenses for warranty service and repair labor by reason
of defects in material or workmanship. The sole responsibility of ADJ Products, LLC under this warranty
shall be limited to the repair of the product, or replacement thereof, including parts, at the sole discretion
of ADJ Products, LLC. All products covered by this warranty were manufactured after August 15, 2012,

and bear identifying marks to that eect.

E. ADJ Products, LLC reserves the right to make changes in design and/or improvements upon its products

without any obligation to include these changes in any products theretofore manufactured.

F. No warranty, whether expressed or implied, is given or made with respect to any accessory supplied with

products described above. Except to the extent prohibited by applicable law, all implied warranties made

by ADJ Products, LLC in connection with this product, including warranties of merchantability or tness,

are limited in duration to the warranty period set forth above. And all warranties, whether expressed or

implied, including warranties of merchantability or tness, are limited in duration to the warranty period set

forth above. The consumer’s and/or dealer’s sole remedy shall be such repair or replacement as is ex­pressly provided above; and under no circumstances shall ADJ Product, LLC be liable for any loss and/or
damage, direct and/or consequential arising out of the use of, and/or inability to use this product.

G. This warranty is the only written warranty applicable to ADJ Products, LLC products, and supersedes all

prior warranties and written descriptions of warranty terms and conditions heretofore published.

MANUFACTURER’S LIMITED WARRANTY PERIODS:

• Non-LED Lighting Products = 1-Year (365 Days) (Including Special Eect Lighting, Intelligent Lighting,

UV lighting, Strobes, Fog Machines, Bubble Machines, Mirror Balls, Par Cans, Trussing, Lighting Stands,
Power/Data Distribution, etc. excluding LED and lamps)

• Laser Products = 1-Year (365 Days) (excluding laser diodes which have a 6-Month Limited Warranty)

• LED Products = 2-Year (730 Days) (excluding batteries which have a 180 Day Limited Warranty)

• NOTE: 2-Year (730 Days) Limited Warranty ONLY applies to product purchased within the United States.

StarTec Series = 1-Year (365 Days) (excluding batteries which have a 180 Day Limited Warranty)

• ADJ DMX Controllers = 2 Year (730 Days)

• American Audio Products = 1 Year (365 Days)

ADJ Products, LLC - www.adj.com - Focus Wash 400 User Manual Page 6

SAFETY GUIDELINES

For Your Own Personal Safety, Please Read and Understand This Manual Completely Before

You Attempt To Install Or Operate This Unit!

• Be sure to save the packing carton in the unlikely event the device may have to be returned for
service

• Do not spill water or other liquids into or on to the device

• Be sure that the local power outlet matches the required voltage for the device

• Do not open up the device for any reason. There are no user serviceable parts inside

• Disconnect the device’s main power when left unused for long periods of time

• Never connect this device to a dimmer pack

• Do not attempt to operate this device if it has been damaged in any way

• Never operate this device with the cover removed

• To reduce the risk of electrical shock or re, do not expose this device to rain or moisture

• Do not attempt to operate this device if the power cord has been frayed or broken.

• Do not attempt to remove or break o the ground prong from the electrical cord. This prong is used
to reduce the risk of electrical shock and re in case of an internal short

• Disconnect from main power before making any type of connection

• Never block the ventilation holes. Always be sure to mount this device in an area that will allow

proper ventilation. Allow about 6” (15cm) between this device and a wall

• This unit is intended for indoor use only. Use of this product outdoors voids all warranties

• Always mount this unit in a safe and stable matter

• Please route your power cord out of the way of foot trac. Power cords should be routed so they

are not likely to be walked on, or pinched by items placed upon or against them

Maximum ambient operating temperature for this xture is 113 degrees F (45 degrees C). Do not

operate this device when ambient temperature exceeds this value!

Keep ammable materials away from this xture!

FIXTURE IS DESIGNED FOR INDOOR USE ONLY! DO NOT EXPOSE TO RAIN OR MOISTURE!

The device should be serviced by qualified service personnel when:
A. The power-supply cord or the plug has been damaged.
B. Objects have fallen on, or liquid has been spilled into, the device.
C. The device has been exposed to rain or water.
D. The appliance does not appear to operate normally or exhibits a marked change in performance.

ADJ Products, LLC - www.adj.com - Focus Wash 400 User Manual Page 7

OVERVIEW

1. Display Screen

2. Left Button

3. Down Button

4. Enter Button

5. Right Button

6. Up Button

7. Carry Handle (x2)

8. Mode Button

9. Service Port

10. Power In

11. Power Out

12. DMX In, 3-pin

13. DMX In, 5-pin

14. DMX Out, 3-pin

15. DMX Out, 5-pin

16. Fuse

17. Mounting Clamp Attachment (x4)

18. Safety Cable Attachment

ADJ Products, LLC - www.adj.com - Focus Wash 400 User Manual Page 8

DMX SET UP

DMX-512: DMX is short for Digital Multiplex. This is a universal protocol used as a form of commu­nication between intelligent fixtures and controllers. A DMX controller sends DMX data instructions
from the controller to the fixture. DMX data is sent as serial data that travels from fixture to fixture
via the DATA “IN” and DATA “OUT” XLR terminals located on all DMX fixtures (most controllers only
have a DATA “OUT” terminal).

DMX Linking: DMX is a language allowing all makes and models of different manufacturers to be
linked together and operate from a single controller, as long as all fixtures and the controller are DMX
compliant. To ensure proper DMX data transmission, try to use the shortest cable path possible
when linking several DMX fixtures. The order in which fixtures are connected in a DMX line does not
influence the DMX addressing. For example, a fixture assigned a DMX address of 1 may be placed
anywhere in a DMX line: at the beginning, at the end, or anywhere in the middle. When a fixture is
assigned a DMX address of 1, the DMX controller knows to send DATA assigned to address 1 to that
unit, no matter where it is located in the DMX chain.

Data Cable (DMX Cable) Requirements (For DMX Operation): The Focus Wash 400 can be con­trolled via DMX-512 protocol. The DMX address is set on the front panel of the fixture. Your unit and
your DMX controller require a standard 3-pin XLR connector for data input and data output. We rec­ommend Accu-Cable DMX cables. If you are making your own cables, be sure to use standard 110­120 Ohm shielded cable (This cable may be purchased at almost all pro lighting stores). Your cables
should be made with a male XLR connector at one end and a female XLR connector on the other.
Also remember that DMX cable must be daisy chained and cannot be split.

Notice: Be sure to follow figures 1 and 2 when making your own cables. Do not use the ground lug
on the XLR connector. Do not connect the cable’s shield conductor to the ground lug or allow the
shield conductor to come in contact with the XLR’s outer casing. Grounding the shield could cause a
short circuit and may result in erratic behavior.

ADJ Products, LLC - www.adj.com - Focus Wash 400 User Manual Page 9

DMX SET UP

Special Note: Line Termination. When longer runs of cable are used, you may need to use a ter­minator on the last unit to avoid erratic behavior. A terminator is a 110-120 ohm 1/4 watt resistor
which is connected between pins 2 and 3 of a male XLR connector (DATA + and DATA -). This unit is
inserted in the female XLR connector of the last unit in your daisy chain to terminate the line. Using a
cable terminator (ADJ part number Z-DMX/T) will decrease the possibilities of erratic behavior.

5-Pin XLR DMX Connectors. Some manufacturers use 5-pin DMX-512 data cables for DATA trans­mission in place of 3-pin. 5-pin DMX fixtures may be implemented in a 3-pin DMX line. When insert­ing standard 5-pin data cables into a 3-pin line, a cable adaptor must be used. These adaptors are
readily available at most electronics stores. The chart below details a proper cable conversion.

ADJ Products, LLC - www.adj.com - Focus Wash 400 User Manual Page 10

INSTALLATION

IP RATING

This device is IP30 rated. It is protected against instrusion of solids larger than 2.5mm in size, such
as tools and thick-gauge wires. The device is NOT protected against liquid instrusion of any

kind.

FLAMMABLE MATERIAL WARNING!

Keep device a minimum of 5.0 feet (1.5m) away from ammable material and/or pyrotechnics.

ELECTRICAL CONNECTIONS

A qualied electrician should be used for all electrical connections and/or installations.

MULTI-DEVICE DAISY CHAINING

• When connected to 240V power, up to 3 devices may be daisy chained together.

• When connected to 110V power, daisy chaining is NOT permitted. In this situation, only
operatethextureasasinglestandalonedevice!

DO NOT INSTALL THE DEVICE IF YOU ARE NOT QUALIFIED TO DO SO!

The unit MUST be installed following all local, national, and country commercial electrical and con­struction codes and regulations.

Before installing or mounting any device, a professional equipment installer MUST be consulted to

determine whether the mounting structure or surface is properly certied to safely support the com­bined weight of the xture, clamps, cables, and accessories.

Overhead xture installations must always be secured with a secondary safety attachment, such as

an appropriately rated safety cable that meets all local, national, and country codes and regulations.

Maximum ambient operating temperature is 113°F (45°C). Do not operate this device when ambient
temperature exceeds this value.

This xture should be installed in areas outside walking paths, seating areas, and areas where unau­thorized personnel might be able to reach the device by hand.

NEVER stand directly below the xture when rigging, removing, or servicing.

Allow approximately 15 minutes for the xture to cool down before servicing.

ADJ Products, LLC - www.adj.com - Focus Wash 400 User Manual Page 11

INSTALLATION

POTENTIAL INTERNAL FIXTURE DAMAGE FROM EXTERNAL SOURCES OF LIGHT BEAMS

External sources of light beams from direct sunlight, lighting moving head fixtures, and lasers which
are focused directly towards the exterior housing and/or penetrate the front lens opening of ADJ
lighting fixtures can cause severe internal damage including burning of optics, dichroic color filters,
glass and metal gobos, prisms, animation wheels, frost filters, irises, shutters, motors, belts, wiring,
discharge lamps, and LEDs.

This issue is not unique to ADJ lighting fixtures; it is a common issue with lighting fixtures from all
manufacturers. Although there is no true way to fully prevent this issue from happening, the guide­lines below can reduce the risk of any potential damage if followed. Contact ADJ Service for more
details.

DO NOT EXPOSE THE FIXTURE AND/OR FRONT LENS OPENING TO LIGHT BEAMS FROM
DIRECT SUNLIGHT, OTHER LIGHTING MOVING HEAD FIXTURES, AND LASERS DURING
UNPACKING, INSTALLATION, USE, AND EXTENDED IDLE TIMES OUTDOORS. DO NOT FOCUS
A LIGHT BEAM FROM ONE LIGHTING FIXTURE DIRECTLY TOWARDS ANOTHER.

ADJ Products, LLC - www.adj.com - Focus Wash 400 User Manual Page 12

INSTALLATION

CLAMP INSTALLATION

This fixture features multiple mounting clamp attachment points, as well as a safety cable attach­ment point, located on the bottom face of the fixture (see the illustration below). When mounting the
fixture to a truss or any other suspended or overhead installation, be sure to secure appropriately
rated clamps (not included) to the clamp attachment points and attach a separate SAFETY CABLE
of the appropriate safety rating to the safety cable rigging point.

SAFETY CABLE

ALWAYS ATTACH A SAFETY

CABLE WHENEVER INSTALLING

THIS FIXTURE IN A SUSPENDED

ENVIRONMENT TO ENSURE

THAT THE FIXTURE WILL NOT

FALL IF THE CLAMP FAILS.

RIGGING

Overhead rigging requires extensive experience, including but not limited to: calculating working
load limits, understanding the installation material being used, and periodic safety inspection of all
installation material and the fixture itself. If you lack these qualifications, do not attempt to perform
the installation yourself. Improper installation can result in bodily injury.

ADJ Products, LLC - www.adj.com - Focus Wash 400 User Manual Page 13

INSTALLATION

NOTICE: The max suitable enviromental temperature for this lighting fixture is 45˚C. Do not place
this lighting fixture in an environment where the temperatures exceed this rating. This will allow the
fixture to run at its best and help prolong the fixture life.

The Focus Wash 400 is fully operational in three different mounting positions: hanging upside-down
from a ceiling or trussing, sideways on trussing, or set on a flat level surface. Be sure this fixture is
kept at least 12m (40ft) away from any flammable materials (decoration etc.). Always use and install
a safety cable (not included) as a safety measure to prevent accidental damage and/or injury in the
event the clamp fails. Never use the carrying handles for secondary attachment.

ADJ Products, LLC - www.adj.com - Focus Wash 400 User Manual Page 14

INSTALLATION

SNOOT INSTALLATION: This device can be fitted with a removable snoot, which can be installed by
following the directions below.

1. Find the four (4) mounting holes located
around the frame of the lens.

2. Align the mounting tabs on the snoot with the
mounting holes on the frame of the lens.

3. Use a screwdriver to insert and tighten
screws into each of the mounting tabs.

4. Installation is now complete!

ADJ Products, LLC - www.adj.com - Focus Wash 400 User Manual Page 15

INSTALLATION

LINEAR LENS INSTALLATION: This device can be fitted with a linear lens, which can be installed
by following the directions below.

1. Find the four (4) mounting holes located
around the frame of the fixture lens.

2. Align the mounting tabs on the linear lens with
the mounting holes on the fixture lens.

3. Use a screwdriver to insert and tighten
screws into each of the mounting tabs.

4. Installation is now complete!

ADJ Products, LLC - www.adj.com - Focus Wash 400 User Manual Page 16

CONTROL PANEL

This fixture includes an easy to navigate control panel display, from which all necessary settings and
adjustments can be made. During normal operating, pressing the MODE button once will access
the fixture’s main menu. Once in the main menu, the UP and DOWN buttons can be used to navi­gate through the different functions. Press the ENTER button to select the option displayed on the
screen, and use the LEFT and RIGHT buttons to adjust the settings for the selected option. Press
the ENTER button once more to confirm the setting. Pressing the MODE button at any time to return
to the main menu without making any adjustments.

System Menu Access: To access the system menu when the fixture is not running on the inter­nal battery, press and hold the MODE button to illuminate the display screen until the DMX
address is displayed. Then navigate to the desired system menu.

ADJ Products, LLC - www.adj.com - Focus Wash 400 User Manual Page 17

SYSTEM MENU

DMX SETTINGS

DMX Address

DMX Channel
Mode

No DMX Status

Primary

Secondary

Status Settings

001 ~ 512

Basic

Standard

Extended

CMY St.

CMY Ext.

Hold Last

Hold Last 2

Blackout

Manual

On / Off

On / Off

Pan Degree

Pan Invert

Tilt Invert

P/T Feedback

Fixture adheres to most recent setting

Fixture adheres to most recent setting and
Zoom will return to 0

Fixture goes into standby mode

Fixture reverts to manual mode settings

630 / 540

On / Off

On / Off

On / Off

PERSONALITY

P/T Speed

Hibernation

Fan Settings Head

Standard

Zoom Speed

Fast

Standard

Stage

TV

Dim Modes

Architectural

Theatre

Stage 2

Dim Speed 0.1 s ~ 10 s

Speed 1 / Speed 2

Off, 1min ~ 99 min

Default 15 min

Auto

High

Low

CONTINUED ON NEXT PAGE

ADJ Products, LLC - www.adj.com - Focus Wash 400 User Manual Page 18

SYSTEM MENU

900 ~ 1500 Hz

2500 Hz

4000 Hz

5000 Hz

PERSONALITY
(cont’d from prev
page)

LED Refresh Rate

Dim Curve

Reset Motors

Display

6000 Hz

10 kHz

15 kHz

20 kHz

25 kHz

Linear

Square

Inv Squa

S Curve

Reset All Motors

Pan/Tilt Reset

Effect Reset

Intensity

Display Invert Yes / No

Screen Saver Delay Off ~ 10 min

Yes / No

Yes / No

Yes / No

1 ~ 10

Default = 15 KHz

Default = 5 min

Key Lock

Service Passcode = 050

Off / On / On1

Pan

Effect Adjust
(Calibration)
Passcode = 050

USB Port Power Off / On

Update Software Off / On

Factory Restore

-128 ~ 127

Tilt

-128 ~ 127

...

Off / On
Passcode = 011

ADJ Products, LLC - www.adj.com - Focus Wash 400 User Manual Page 19

SYSTEM MENU

Pan 000 ~ 255

Pan Fine 000 ~ 255

MANUAL

INTERNAL
PROGRAMS

Tilt 000 ~ 255

Tilt Fine 000 ~ 255

... 000 ~ 255

Speed 000 - 255

Program 1

Fade 000 - 255

Speed 000 - 255

Program 2

Fade 000 - 255

Speed 000 - 255

Program 3

Fade 000 - 255

Speed 000 - 255

Program 4

Fade 000 - 255

Speed 000 - 255

Program 5

Fade 000 - 255

Speed 000 - 255

Program 6

Fade 000 - 255

INFORMATION

Program 7

Fixture Life Time

Total LED Time

CONTINUED ON NEXT PAGE

Speed 000 - 255

Fade 000 - 255

Power On Time

P-On Time-R
(Power On Resettable Time)

P-On Time-Reset
(Power On Time
Reset)

LED On Time

LED On Time-R

LED Hours Reset Passcode = 050

Passcode = 050

ADJ Products, LLC - www.adj.com - Focus Wash 400 User Manual Page 20

SYSTEM MENU

INFORMATION

(cont’d from prev

page)

Fixture Temps

Fan Info (RPM)

DMX Values

Error Logs

Software Version

LEDs

Base

Reset LED Temp

Reset Base Temp

LED Fan

Base Fan

Pan

Pan Fine

...

Fixture Errors

Reset Error Log

Current

Max Resettable

Current

Max Resettable

Yes / No

Yes / No

Yes / No

Passcode = 050

Passcode = 050

scrolls through
error list

Passcode = 050

ADJ Products, LLC - www.adj.com - Focus Wash 400 User Manual Page 21

DMX ADDRESSING

All fixtures should be given a DMX starting address when operating with a DMX controller, in order to
ensure that the correct fixture responds to the correct control signal. This digital starting address is
the channel number from which the fixture starts to “listen” to the digital control signal sent out from
the DMX controller. This starting DMX address is assigned by setting the correct DMX address on
the digital control display on the fixture.

You can set the same starting address for all fixtures or a group of fixtures, or set different addresses
for each individual fixture. Setting all fixtures to the same DMX address will cause all fixtures to react
in the same way. In this case, please note that changing the settings of one channel will affect all the
fixtures simultaneously.

If you set each fixture to a different DMX address, each unit will start to “listen” to the channel num­ber you have set, based on the quantity of DMX channels of each fixture. That means changing the
settings of one channel will only affect the selected fixture.

As an example, when operating this fixture model in Basic (17 channel) mode, you should set the
starting DMX address of the first unit to 1, the second unit to 18 (1 + 17), the third unit to 35 (1 + 17 +

17), and so on. (See the chart below for more details.)

Channel Mode Unit 1 Address Unit 2 Address Unit 3 Address Unit 4 Address

Basic

Standard

Extended

CMY St.

CMY Ext.

1 18 35 52

1 23 45 67

1 25 49 73

1 19 37 55

1 25 49 73

ADJ Products, LLC - www.adj.com - Focus Wash 400 User Manual Page 22

CHANNEL

DMX TRAITS

Basic Standard Ext

1 1 1 1 1 000 - 255

2 2 2 2 000 - 255

2 3 3 3 3 000 - 255

4 4 4 4 000 - 255

3 5 5 000 - 255

4 6 6 000 - 255

5 7 7 000 - 255

6 8 8 000 - 255

7 9 9 000 - 255

8 10 10 000 - 255

CMY

St.

5 5 000 - 255

6 7 000 - 255

CMY

Ext

6 000 - 255

VALUES FUNCTION

Pan Movement, 540/630 Degrees

Pan Fine Movement

Tilt Movement, 270 Degrees

Tilt Fine Movement

Red, 0% - 100%

Green, 0% - 100%

Blue, 0% - 100%

Amber, 0% - 100%

Cyan, 0% - 100%

Lime, 0% - 100%

Cyan, (0-100% Cyan)

Cyan Fine

Magenta, 0% - 100%

8 000 - 255

7 9 000 - 255

10 000 - 255

9 11 11 8 11 000 - 255

000 - 031 No Function

032 - 076 2700K

10 12 12 9 12

11 13 13 10 13

077 - 121 3200K

122 - 166 4000K

167 - 211 5600K

212 - 255 6500K

000

001 - 060

Magenta Fine

Yellow, 0% - 100%

Yellow Fine

Color Temperature Linear 2700K -

10000K

Color Temperature Presets

Color Wheel

Open

Virtual Swatch Colors (see Virtual
Swatch Colors section)

061 - 179 Open

180 - 201 Color Scroll Clockwise, fast to slow

CONTINUED ON NEXT PAGE

ADJ Products, LLC - www.adj.com - Focus Wash 400 User Manual Page 23

CHANNEL

DMX TRAITS

Basic Standard Ext

11 13 13 10 13

14 14 11 14

12 15 15 15 000 - 255

CMY

St.

CMY

Ext

VALUES FUNCTION

202 - 207 Stop

208 - 229

230 - 234 Open

235 - 239 Random Slots Fast

240 - 244 Random Slots Medium

245 - 249 Random Slots Slow

250 - 255 Open

000 No Function

001 - 255 Shift CT, Red to Green

Color Wheel (cont’d)

Color Scroll Counter-Clockwise, slow
to fast

Color Temperature Red to Green

Color Macros (see Color Macros
Chart)

000 - 031 Shutter Closed (LEDs Off)

032 - 063 Shutter Open (LEDs On)

064 - 095 Strobe effect, slow to fast

13 16 16 12 16

14 17 17 13 17 000 - 255

18 18 18 000 - 255

15 19 19 14 19 000 - 255

20 20 000 - 255

096 - 127 Shutter Open (LEDs On)

128 - 159 Pulse effect in sequences

160 - 191 Shutter Open (LEDs On)

192 - 223 Random strobe effect, slow to fast

224 - 255 Shutter Open (LEDs On)

Shutter

Dimmer Intensity, 0 to 100%

Dimmer Fine

Zoom, wide to narrow

Zoom Fine

CONTINUED ON NEXT PAGE

ADJ Products, LLC - www.adj.com - Focus Wash 400 User Manual Page 24

CHANNEL

DMX TRAITS

Basic Standard Ext

CMY

St.

CMY

Ext

VALUES FUNCTION

Dim Modes

000 - 020 Standard

021 - 040 Stage

041 - 060 TV

061 - 080 Architectural

081 - 100 Theatre

101 - 120 Stage 2

Dimming Speed

121 0.1 s

122 0.2 s

123 0.3 s

124 0.4 s

125 0.5 s

20 21 15 21

126 0.6 s

127 0.7 s

128 0.8 s

129 0.9 s

130 1.0 s

131 1.5 s

132 2.0 s

133 3.0 s

134 4.0 s

135 5.0 s

136 6.0 s

137 7.0 s

138 8.0 s

139 9.0 s

140 10.0 s

141 - 255 Default

CONTINUED ON NEXT PAGE

ADJ Products, LLC - www.adj.com - Focus Wash 400 User Manual Page 25

CHANNEL

DMX TRAITS

Basic Standard Ext

22 16 22

16 21 23 17 23 000 - 255

CMY

St.

CMY

Ext

VALUES FUNCTION

000 - 020 Linear

021 - 040 Square

041 - 060 Inv. Squa

061 - 080 S. Curve

081 - 255 No Function

000 - 010 Default Refresh Rate (15 KHz)

011 900 Hz

012 910 Hz

013 920 Hz

014 930 Hz

Dim Curves

Pan/Tilt Speed, max to min

Special Functions

17 22 24 18 24

015 940 Hz

016 950 Hz

017 960 Hz

018 970 Hz

019 980 Hz

020 990 Hz

021 1000 Hz

022 1010 Hz

023 1020 Hz

024 1030 Hz

025 1040 Hz

026 1050 Hz

027 1060 Hz

028 1070 Hz

029 1080 Hz

030 1090 Hz

031 1100 Hz

CONTINUED ON NEXT PAGE

ADJ Products, LLC - www.adj.com - Focus Wash 400 User Manual Page 26

CHANNEL

DMX TRAITS

Basic Standard Ext

CMY

St.

CMY

Ext

VALUES FUNCTION

Special Functions (cont’d)

032 1110 Hz

033 1120 Hz

034 1130 Hz

035 1140 Hz

036 1150 Hz

037 1160 Hz

038 1170 Hz

039 1180 Hz

040 1190 Hz

041 1210 Hz

042 1220 Hz

043 1230 Hz

17 22 24 18 24

044 1240 Hz

045 1250 Hz

046 1260 Hz

047 1270 Hz

048 1280 Hz

049 1290 Hz

050 1300 Hz

051 1310 Hz

052 1320 Hz

053 1330 Hz

054 1340 Hz

055 1350 Hz

056 1360 Hz

057 1370 Hz

058 1380 Hz

059 1390 Hz

CONTINUED ON NEXT PAGE

ADJ Products, LLC - www.adj.com - Focus Wash 400 User Manual Page 27

CHANNEL

DMX TRAITS

Basic Standard Ext

CMY

St.

CMY

Ext

VALUES FUNCTION

Special Functions (cont’d)

060 1400 Hz

061 1410 Hz

062 1420 Hz

063 1430 Hz

064 1440 Hz

065 1450 Hz

066 1460 Hz

067 1470 Hz

068 1480 Hz

069 1490 Hz

070 1500 Hz

071 2500 Hz

17 22 24 18 24

072 4000 Hz

073 5000 Hz

074 6000 Hz

075 10 KHz

076 15 KHz

077 20 KHz

078 25 KHz

079 Disable LED Refresh Rate

080 - 089 Enable blackout while pan/tilt moving

090 - 099 Disable blackout while pan/tilt moving

100 - 105 Fan Mode Low

106 - 111 Fan Mode High

112 - 117 Fan Mode Auto

118 - 139 No function

140 - 149 Reset all

150 - 159 Reset pan/tilt

160 - 169 Reset effect

CONTINUED ON NEXT PAGE

ADJ Products, LLC - www.adj.com - Focus Wash 400 User Manual Page 28

CHANNEL

DMX TRAITS

Basic Standard Ext

17 22 24 18 24

CMY

St.

CMY

Ext

VALUES FUNCTION

Special Functions (cont’d)

170 - 174 Enable Zoom Speed Fast

175 - 179 Disable Zoom Speed Fast

180 - 189 Internal Program 1 (Scenes 1-8)

190 - 199 Internal Program 2 (Scenes 9-16)

200 - 209 Internal Program 3 (Scenes 17-24)

210 - 219 Internal Program 4 (Scenes 25-32)

220 - 229 Internal Program 5 (Scenes 33-40)

230 - 239 Internal Program 6 (Scenes 41-48)

240 - 249 Internal Program 7 (Scenes 49-56)

250 - 255 No Function

ADJ Products, LLC - www.adj.com - Focus Wash 400 User Manual Page 29

COLOR MACROS CHART

MACRO

NUMBER

1 001 - 004 80 255 234 80 0 0

2 005 - 008 80 255 164 80 0 0

3 009 - 012 77 255 112 77 0 0

4 013 - 016 117 255 83 83 0 0

5 017 - 020 160 255 77 77 0 0

6 021 - 024 223 255 83 83 0 0

7 025 - 028 255 243 77 77 0 0

8 029 - 032 255 200 74 74 0 0

9 033 - 036 255 166 77 77 0 0

10 037 - 040 255 125 74 74 0 0

11 041 - 044 255 97 77 74 0 0

12 045 - 048 255 71 77 71 0 0

13 049 - 052 255 83 134 83 0 0

14 053 - 056 255 93 182 93 0 0

DMX

VALUE

RED GREEN BLUE AMBER CYAN LIME

15 057 - 060 255 96 236 96 0 0

16 061 - 064 238 93

17 065 - 068 196 87 255 87 0 0

18 069 - 072 150 90 255 90 0 0

19 073 - 076 100 77 255 77 0 0

20 077 - 080 77 100 255 77 0 0

21 081 - 084 67 148 255 67 0 0

22 085 - 088 77 195 255 77 0 0

23 089 - 092 77 234 255 77 0 0

24 093 - 096 158 255 144 144 0 0

25 097 - 100 255 251 153 153 0 0

26 101 - 104 255 175 147 147 0 0

27 105 - 108 255 138 186 138 0 0

28 109 - 112 255 147 251 147 0 0

29 113 - 116 151 138 255 138 0 0

255 93 0 0

30 117 - 120 99 0 255 100 0 0

31 121 - 124 138 169 255 138 0 0

32 125 - 128 255 255 255 255 0 0

ADJ Products, LLC - www.adj.com - Focus Wash 400 User Manual Page 30

COLOR MACROS CHART

MACRO

NUMBER

33 129 - 132 254 206 143 0 0 0

34 133 - 136 254 177 153 0 0 0

35 137 - 140 254 192 138 0 0 0

36 141 - 144 254 165 98 0 0 0

37 145 - 148 254 121 0 0 0 0

38 149 - 152 176 17 0 0 0 0

39 153 - 156 96 0 11 0 0 0

40 157 - 160 234 139 171 0 0 0

41 161 - 164 224 5 97 0 0 0

42 165 - 168 175 77 173 0 0 0

43 169 - 172 119 130 199 0 0 0

44 173 - 176 147 164 212 0 0 0

45 177 - 180 88 2 163 0 0 0

46 181 - 184 0 38 86 0 0 0

DMX

VALUE

RED GREEN BLUE AMBER CYAN LIME

47 185 - 188 0 142 208 0 0 0

48 189 - 192 52 148

49 193 - 196 1 134 201 0 0 0

50 197 - 200 0 145 212 0 0 0

51 201 - 204 0 121 192 0 0 0

52 205 - 208 0 129 184 0 0 0

53 209 - 212 0 83 115 0 0 0

54 213 - 216 0 97 166 0 0 0

55 217 - 220 1 100 167 0 0 0

56 221 - 224 0 40 86 0 0 0

57 225 - 228 209 219 182 0 0 0

58 229 - 232 42 165 85 0 0 0

59 233 - 236 0 46 35 0 0 0

60 237 - 240 8 107 222 0 0 0

61 241 - 244 254 0 0 0 0 0

209 0 0 0

62 245 - 248 0 254 0 0 0 0

63 249 - 252 0 0 254 0 0 0

64 253 - 255 0 0 0 254 0 0

ADJ Products, LLC - www.adj.com - Focus Wash 400 User Manual Page 31

VIRTUAL SWATCH COLORS

ADJ Products, LLC - www.adj.com - Focus Wash 400 User Manual Page 32

COLOR TEMPERATURE CHART

DMX

VALUES

000 - 026 No function 047 4700

027 2700 048 4800

028 2800 049 4900

029 2900 050 5000

030 3000 051 5100

031 3100 052 5200

032 3200 053 5300

033 3300 054 5400

034 3400 055 5500

035 3500 056 5600

036 3600 057 5700

037 3700 058 5800

038 3800 059 5900

COLOR

TEMPERATURE

DMX

VALUES

COLOR

TEMPERATURE

039 3900 060 6000

040 4000 061 6100

041 4100 062 6200

042 4200 063 6300

043 4300 064 6400

044 4400 065 6500

045 4500 066 - 255 10000

046 4600

ADJ Products, LLC - www.adj.com - Focus Wash 400 User Manual Page 33

DIMMER MODES & CURVES

ADJ Products, LLC - www.adj.com - Focus Wash 400 User Manual Page 34

CLEANING & MAINTENANCE

WARNING! DISCONNECT UNIT FROM POWER BEFORE PERFORMING ANY

CLEANING OR MAINTENANCE PROCEDURES!

ALWAYS ALLOW THE FIXTURE TO COOL FOR AT LEAST 15 MINUTES BEFORE

PERFORMING ANY CLEANING OR MAINTENANCE!

CLEANING

Frequent cleaning is recommended to ensure proper function, optimized light output, and an extend­ed life. The frequency of cleaning depends on the environment in which the fixture operates: damp,
smoky, or particularly dirty environments can cause greater accumulation of dirt on the fixture’s
optics. Clean periodically with a soft cloth to avoid dirt/debris accumulation.

NEVER use alcohol, solvents, or ammonia-based cleaners.

MAINTENANCE

Regular inspections are recommended to ensure proper function and extended life. There are no
user serviceable parts inside this fixture. Please refer all other service issues to an authorized ADJ
service technician. Should you need any spare parts, please order genuine parts from an authorized
ADJ dealer.

Please refer to the following points during routine inspections:

• A detailed electrical check by an approved electrical engineer every three months, to make sure
the circuit contacts are in good condition and prevent overheating.

• Be sure all screws and fasteners are securely tightened at all times. Loose screws may fall out
during normal operation, resulting in damage or injury as larger parts could fall.

• Check for any deformations on the housing, color lenses, rigging hardware and rigging points
(ceiling, suspension, trussing). Deformations in the housing could allow for dust to enter into the
fixture. Damaged rigging points or unsecured rigging could cause the fixture to fall and seriously
injure a person(s).

• Electric power supply cables must not show any damage, material fatigue or sediments.

ADJ Products, LLC - www.adj.com - Focus Wash 400 User Manual Page 35

FUSE REPLACEMENT

Disconnect the unit from the power source, then use a flat head screw driver to unscrew the fuse
holder located above the DMX ports. Remove the bad fuse and replace with a new one, then screw
the fuse holder back in. Replace only with a new fuse of the same type and rating.

SOFTWARE UPDATES

ONLY QUALIFIED TECHNICIANS SHOULD PERFORM THIS FUNCTION! NOTE ALL MENU SET­TINGS BEFORE UPDATING SOFTWARE!
FIXTURE SOFTWARE CANNOT BE DOWNGRADED!
DOWNLOAD FIXTURE SOFTWARE TO PC ONLY! (NO MAC SUPPORT)
PLEASE CONTACT ADJ CUSTOMER SERVICE FOR FURTHER INFORMATION.

1. Contact ADJ customer service to obtain the updated software. Download software to a USB
flash drive. In order to minimize the risk of downloading the incorrect software to your device,
make sure that the desired update files are the only files on the USB flash drive.

2. Disconnect any DMX connections from your device. Insert the USB flash drive into the service
port on your device.

3. Use the display screen control panel to navigate to Personality > Service > USB Port Power.
See the System Menu section of this manual for detailed instructions. Enter the passcode when
prompted, and switch the USB Port Power setting to ON.

4. Highlight the desired file and press ENTER to select it and begin the download.

5. The unit will now update, run an automatic software check, and reset. This may take some time.

6. Repeat this process for each software update file.

7. Verify by navigating to Information > Software Version and confirming that the correct software
version number is shown there (see the System Menu section of this manual for detailed instruc­tions).

ADJ Products, LLC - www.adj.com - Focus Wash 400 User Manual Page 36

DIMENSIONAL DRAWINGS

Without Snoot

Snoot Installed

Drawings may not be to scale.

ADJ Products, LLC - www.adj.com - Focus Wash 400 User Manual Page 37

SPECIFICATIONS

SOURCE:

• 400W RGBACL LED

• 50,000 Hour Average LED Life*

*May vary depending on several factors including but not limited to: Environmental Conditions, Power/Voltage, Usage Patterns (On-O Cycling), Con-

trol, and Dimming.

PHOTOMETRIC DATA:

• Zoom Range 10° - 46°

• Color Temperature: 10000K

• 4,600 Total Lumen Fixture Output

• Lux @ 10’: 10,384 lx (965 foot candles), 1.8’ diameter

• CRI: 94

• CRI R9: 87.3

• TM30 Rf: 90.8

• TM30 Rg: 99.5

COLOR:

• RGBWACL (Red, Green, Blue, Amber, Cyan, Lime)

EFFECTS:

• RGBACL Color Mixing

• 10~46-degree Motorized Zoom

• Electronic Strobe

• Color Temperature Red to Green control via DMX

• Linear Color Temperature control, 2700k to 10,000k

• Preset Color Temperatures (2700k, 3200k, 4000k, 5600k and 6500k)

CONTROL / CONNECTIONS:

• 3 DMX Channel Modes (16, 21 & 23 Channel Modes)

• Selectable LED Refresh Rates, 900Hz to 25K Hz.

• Linear Dimming with user selectable Dim Curves, Dim Modes and Dim Speeds

• 6-button Control Panel and LCD Menu Display

• RDM (Remote Device Management)

• Locking 3-pin and 5-pin XLR Connector In/Out

• IP65 Locking Power Connector In/Out

• With Wired Digital Communication Network

SIZE / WEIGHT:

• Length: 10.96” (278.43mm)

• Width: 8.40” (213.33mm)

• Vertical Height (Without Snoot): 19.61” (498.1mm)

• Vertical Height (Snoot Installed): 22.37” (568.1mm)

• Weight: 23.5 lbs. (10.7 kg)

ELECTRICAL / THERMAL:

• Multi-voltage: AC 100-240V - 47/63Hz

• 438W Max Power Consumption

• Multiple Unit Power Linking

• 5°F to 113°F (-15°C to 45°C)

APPROVALS / RATINGS:

• CE | cETLus (Pending) | IP20

Specicationsanddocumentationsubjecttochangewithoutnotice.

ADJ Products, LLC - www.adj.com - Focus Wash 400 User Manual Page 38

ADJ Products, LLC - www.adj.com - Focus Wash 400 User Manual Page 39