Page 1
FOCUS SPOT TWO
©2016 ADJ Products, LLC all rights reserved. Information,
specications, diagrams, images, and instructions herein are
subject to change without notice. ADJ Products, LLC logo and
identifying product names and numbers herein are trademarks
of ADJ Products, LLC. Copyright protection claimed includes all
forms and matters of copyrightable materials and information
now allowed by statutory or judicial law or hereinafter granted.
Product names used in this document may be trademarks or
registered trademarks of their respective companies and are
hereby acknowledged. All non-ADJ Products, LLC brands and
product names are trademarks or registered trademarks of their
respective companies.
ADJ Products, LLC and all aliated companies hereby disclaim any and all liabilities for property, equipment, building,
and electrical damages, injuries to any persons, and direct or
indirect economic loss associated with the use or reliance of
any information contained within this document, and/or as a
result of the improper, unsafe, unsucient and negligent assembly, installation, rigging, and operation of this product.
11/18
User Instructions
Europe Energy Saving Notice
Energy Saving Matters (EuP 2009/125/EC)
Saving electric energy is a key to help protecting the enviroment.
Please turn o all electrical products when they are not in use. To
avoid power consumption in idle mode, disconnect all electrical
equipment from power when not in use. Thank you!
Page 2
Focus Spot Two General Instructions Focus Spot Two General Information
Unpacking: Thank you for purchasing the Focus Spot Two by ADJ
Products, LLC. Every Focus Spot Two has been thoroughly tested and
has been shipped in perfect operating condition. Carefully check the
shipping carton for damage that may have occurred during shipping.
If the carton appears to be damaged, carefully inspect your xture for
any damage and be sure all equipment necessary to operate the unit
has arrived intact. In the event damage has been found or parts are
missing, please contact our toll free customer support number for further instructions. Please do not return this unit to your dealer without
contacting customer support rst.
Introduction: The Focus Spot Two is a DMX intelligent, LED moving
head fixture. The Focus Spot Two can operate as a stand alone fixture
or in a Master/Slave set up. The Focus Spot Two has three operating
modes; a sound active, show mode, DMX controlled. This fixture is
suitable for theaters, studios, retail stores, and other similar locations.
For best results use fog or special effects smoke to enhance the beams
projections.
Customer Support: ADJ Products, LLC provides a toll free cus-
tomer support line, to provide help and to answer any question should
you encounter problems during your set up or initial operation. You
may also visit us on the web at www.adj.com for any comments or
suggestions. Service Hours are Monday through Friday 8:00 a.m. to
4:30 p.m. Pacic Standard Time.
Voice: (800) 322-6337
Fax: (323) 582-2941
E-mail: support@americandj.com
Warning! To prevent or reduce the risk of electrical shock or re, do
not expose this unit to rain or moisture.
Warning! This may cause severe eye damage. Avoid looking directly
into the light source at all times!
To optimize the performance of this product, please read these
operating instructions carefully to familiarize yourself with the basic
operations of this unit. These instructions contain important safety
information regarding the use and maintenance of this unit. Please
keep this manual with the unit, for future reference.
Focus Spot Two Features
• DMX-512 Protocol Compatible (2 DMX Channel Modes: 16 Chan-
nels & 18 Channels)
• 3 Operating Modes - Sound Active, Show Mode, & DMX Control
• 5 Dimmer Curves (Standard, Stage, TV, Architectural, & Theatre)
• Internal Microphone
• Digital Display for Address and Function Setting
• 4 Preprogrammed Shows
• UC IR and Airstream IR Compatiable (Not Included)
Focus Spot Two Warranty Registration
The Focus Spot Two carries a 2 year (730 days) limited warranty.
Please fill out the enclosed warranty card to validate your purchase
and warranty. You may also register your product online at www. adjproducts.com. All returned service items whether under warranty or
not, must be freight pre-paid and accompany a return authorization
(R.A.) number. If the unit is under warranty you must provide a copy
of your proof of purchase invoice. Please contact ADJ Products, LLC
customer support for a R.A. number.
Focus Spot Two Handling Precautions
Caution! There are no user serviceable parts inside this unit. Do not
attempt any repairs yourself, doing so will void your manufactures
warranty. In the unlikely event your unit may require service please
contact ADJ Products, LLC.
During operation the housing may become extremely hot. Avoid
touching the unit with bare hands while in use.
ADJ Products, LLC will not accept any liability for any resulting damages caused by the non-observance of this manual or any unauthor-
ized modication to this unit.
ADJ Products, LLC - www.adj.com - Focus Spot Two Instruction Manual Page 3ADJ Products, LLC - www.adj.com - Focus Spot Two Instruction Manual Page 2
Page 3
Focus Spot Two Safety Precautions
For Your Own Personal Safety, Please Read and Understand This
Manual Completely Before You Attempt To Install Or Operate
This Unit!
• To reduce the risk of electrical shock or re, do not expose this unit
rain or moisture
• Do not spill water or other liquids into or on to your unit.
• Be sure that the local power outlet match that of the required volt age for your unit.
• Do not attempt to operate this unit if the power cord has been
frayed or broken.
• Do not attempt to remove or break o the ground prong from
the electrical cord. This prong is used to reduce the risk of electrical
shock and re in case of an internal short.
• Disconnect from main power before making any type of connection.
• Do not remove the cover under any conditions. There are no user
serviceable parts inside.
• Never operate this unit when it’s cover is removed.
• Always be sure to mount this unit in an area that will allow proper
ventilation. Allow about 6” (15cm) between this device and a wall.
• Do not attempt to operate this unit, if it becomes damaged.
• This unit is intended for indoor use only, use of this product out doors voids all warranties.
• Always mount this unit in safe and stable matter.
• Power-supply cords should be routed so that they are not likely to
be walked on or pinched by items placed upon or against them,
paying particular attention to cords at plugs, convenience recep tacles, and the point where they exit from the appliance.
• Cleaning -The fixture should be cleaned only as recommended by
the manufacturer. See page 33 for cleaning details.
• Heat -This fixture should be situated away from heat sources such
as radiators, heat registers, stoves, or other appliances (including
amplifiers) that produce heat.
• The fixture should be serviced by qualified service personnel when:
A. Objects have fallen, or liquid has been spilled into the appliance.
B. The appliance has been exposed to rain or water.
C. The appliance does not appear to operate normally or exhibits
a marked change in performance.
Focus Spot Two Safety Precautions
RISK GROUP 3 - RISK OF EXPOSURE TO ULTRAVIOLET (UV) RADIATION!
FIXTURE EMITS HIGH INTENSITY ULTRAVIOLET (UV) LIGHT AT A
WAVELENGTH OF 399NM - 427NM.
WEAR PROPER EYE AND SKIN PROTECTION.
AVOID PROLONGED PERIODS OF EXPOSURE.
AVOID WEARING WHITE COLOR CLOTHING AND/OR USING (UV)
PAINTS ON SKIN.
AVOID DIRECT EYE AND/OR SKIN EXPOSURE AT DISTANCES
SHORTER THAN 11 feet (3.3m).
DO NOT OPERATE FIXTURE WITH DAMAGED OR MISSING EXTERNAL
COVER PROTECTIVE LENS.
DO NOT LOOK DIRECTLY INTO THE (UV) LIGHT AND/OR VIEW (UV)
LIGHT DIRECTLY WITH OPTICAL INSTRUMENTS THAT MAY CONCENTRATE
THE LIGHT/RADIATION OUTPUT.
INDIVIDUALS SUFFERING FROM A RANGE OF EYE CONDITIONS,
SUNLIGHT EXPOSURE DISORDERS, OR INDIVIDUALS USING
PHOTOSENSITIVE MEDICATION, MAY RECEIVE DISCOMFORT IF
EXPOSED TO THE ULTRAVIOLET (UV) LIGHT EMITTED FROM THIS
FIXTURE.
ADJ Products, LLC - www.adj.com - Focus Spot Two Instruction Manual Page 5ADJ Products, LLC - www.adj.com - Focus Spot Two Instruction Manual Page 4
Page 4
Focus Spot Two Mounting
Focus Spot Two Mounting
When installing the unit, the trussing or area of installation must be
able to hold 10 times the weight without any deformation. When
installing the unit must be secured with a secondary safety attachment, e.g. and appropriate safety cable. Never stand directly below
the unit when mounting, removing, or servicing the unit.
Overhead mounting requires extensive experience, including calculating working load limits, installation material being used, and perodic
safety inspection of all installation material and unit. If you lack these
qualications, do not attempt the installation yourself.
The installaiton should be checked by a skilled person once a year.
NOTICE: The suitable enviromental temperature for this lighting xture is between -25˚ C to 45˚ C. Do not place this lighting
xture in an enviroment where the temperatures are under or
above the temperatures stated above. This will allow the xture
to run at its best and help prolong the xture life.
Clamp
Screew
Suspender
The Focus Spot Two is fully operational in three dierent positions,
hanging upside-down from a ceiling or trussing, mounted sideways
on trussing, or set on a at level surface. Be sure this xture is kept
at least 0.5m away from any ammable materials (decoration etc.).
Always use and install the supplied safety cable as a safety measure
to prevent accidental damage and/or injury in the event the clamp
fails (see next page).
ADJ Products, LLC - www.adj.com - Focus Spot Two Instruction Manual Page 6 ADJ Products, LLC - www.adj.com - Focus Spot Two Instruction Manual Page 7
Screw one clamp via a M12 screw and nut to the included
bracket. Attach the bracket using the omega locks to the
bottom of the Focus Spot Two. Attach and pull the safety-cable
through one of the safety holes located on the bottom base and
over the trussing system or a safe xation spot. Insert the end
in the carabine and tighten the safety screw.
Page 5
Focus Spot Two CAD Drawing
Focus Spot Two Base Layout
237mm/9.33”
385mm/15.15”
173mm/6.81”
2 3
1
1. IRreceiver:ToreceivetheIRsignal;
2. LED:
DMX On DMXinputpresent
MASTER On MasterMode
SLAVE ON Slave Mode
SOUND Flashing Sound activation
3. Button:
MENU Toselecttheprogramming functions
UP Togoforwardintheselectedfunctions
DOWN Togobackwardintheselectedfunctions
ENTER Toconrmtheselectedfunctions
4. Display:Toshowthevariousmenusandtheselectedfunction;
5. DMXIn/Out: 3‐pinXLRconnectorsforDMX512operation;
6. PowerIn/out: Connectors for powerinput/output;
7. Fuse(T6.3Amp):Protectstheunitfromover‐voltageorshortcircuit.
4
5
6
7
ADJ Products, LLC - www.adj.com - Focus Spot Two Instruction Manual Page 9ADJ Products, LLC - www.adj.com - Focus Spot Two Instruction Manual Page 8
Page 6
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
DMX512
DMX+,DMX-,COMMON
1
2
3
Termination reduces signal errors and
avoids signal transmission problems
and interference. It is always advisable
to connect a DMX terminal, (Resistance
120 Ohm 1/4 W) between PIN 2 (DMX-)
and PIN 3 (DMX +) of the last fixture.
POWER
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
Focus Spot Two DMX Set Up
Focus Spot Two DMX Set Up
Power Supply: The ADJ Focus Spot Two contains a automatic volt-
age switch, which will auto sense the voltage when it is plugged into
the power source. With this switch there is no need to worry about the
correct power voltage, this unit can be plugged in anywhere.
DMX-512: DMX is short for Digital Multiplex. This is a universal pro-
tocol used by most lighting and controller manufactures as a form of
communication between intelligent fixtures and controllers. A DMX
controller sends DMX data instructions from the controller to the fixture. DMX data is sent as serial data that travels from fixture to fixture
via the DATA “IN” and DATA “OUT” XLR terminals located on all DMX
fixtures (most controllers only have a DATA “OUT” terminal).
DMX Linking: DMX is a language allowing all makes and models
of dierent manufactures to be linked together and operate from a
single controller, as long as all xtures and the controller are DMX
compliant. To ensure proper DMX data transmission, when using
several DMX fixtures try to use the shortest cable path possible. The
order in which fixtures are connected in a DMX line does not influence
the DMX addressing. For example; a fixture assigned a DMX address
of 1 may be placed anywhere in a DMX line, at the beginning, at the
end, or anywhere in the middle. Therefore, the first fixture controlled
by the controller could be the last fixture in the chain. When a fixture
is assigned a DMX address of 1, the DMX controller knows to send
DATA assigned to address 1 to that unit, no matter where it is located
in the DMX chain.
Data Cable (DMX Cable) Requirements (For DMX and Master/Slave
Operation): The Focus Spot Two can be controlled via DMX-512 proto-
col. The Focus Spot Two has 2 DMX channel modes; 16 channel mode
& 18 channel mode. The DMX address is set electronically using the controls on the front panel of
the unit. Your unit and your DMX controller require
a approved DMX-512 110 Ohm Data cable for data
input and data output (Figure 1). We recommend
Accu-Cable DMX cables. If you are making your
own cables, be sure to use standard 110-120 Ohm
shielded cable (This cable may be purchased at
almost all professional sound and lighting stores).
Figure 1
Your cables should be made with a male and female XLR connector on
either end of the cable. Also remember that DMX cable must be daisy
chained and cannot be split.
Notice: Be sure to follow gures two and three when making your own
cables. Do not use the ground lug on the XLR connector. Do not connect the cable’s shield conductor to the ground lug or allow the shield
conductor to come in contact with the XLR’s outer casing. Grounding
the shield could cause a short circuit and erratic behavior.
COMMON
1
DMX512 IN
3
3-PIN XLR
2
Figure 2
XLR Pin Conguration
Pin 1 = Ground
Pin 2 = Data Compliment (negative)
Pin 3 = Data True (positive)
Figure 4
XLR Male Socket
1 Ground
DMX512 OT
3-PIN XLR
2 Cold
3 Hot
1
3
2
XLR Female Socket
2 Cold
DMX +
DMX -
1 Ground
3 Hot
Figure 3
Special Note: Line Termination.
used, you may need to use a terminator on the last unit to avoid erratic
When longer runs of cable are
behavior. A terminator is a 110-120 ohm 1/4 watt resistor which is connected between pins 2 and 3 of a male XLR connector (DATA + and
DATA -). This unit is inserted in the female XLR connector of the last
unit in your daisy chain to terminate the line. Using a cable terminator
(ADJ part number Z-DMX/T) will decrease the possibilities of erratic
behavior.
Termination reduces signal errors and
1
avoids signal transmission problems
3
and interference. It is always advisable
2
to connect a DMX terminal, (Resistance
120 Ohm 1/4 W) between PIN 2 (DMX-)
and PIN 3 (DMX +) of the last fixture.
ADJ Products, LLC - www.adj.com - Focus Spot Two Instruction Manual Page 10
ADJ Products, LLC - www.adj.com - Focus Spot Two Instruction Manual Page 11
Page 7
Focus Spot Two DMX Set Up
Focus Spot Two 16 Channel Mode
5-Pin XLR DMX Connectors.
Some manufactures use 5-pin DMX-
512 data cables for DATA transmission in place of 3-pin. 5-pin DMX
xtures may be implemented in a 3-pin DMX line. When inserting standard 5-pin data cables in to a 3-pin line a cable adaptor must be used,
these adaptors are readily available at most electric stores. The chart
below details a proper cable conversion.
3-Pin XLR to 5-Pin XLR Conversion
Conductor 5-Pin XLR Male (In)3-Pin XLR Female (Out)
Ground/Shield
Data Compliment (- signal)
Data True (+ signal)
Not Used
Not Used
Pin 1
Pin 2
Pin 3
Pin 1
Pin 2
Pin 3
Pin 4 - Do Not Use
Pin 5 - Do Not Use
Channel Value Function
1 0 - 255 PAN MOVEMENT 0° - 540
2 0 - 255 TILT MOVEMENT 0° - 230°
3 COLOR
0 - 14 WHITE
15 - 29 RED
30 - 44 BLUE
45 - 59 GREEN
60 - 74 YELLOW
75 - 89 PINK
90 - 104 LIGHT BLUE
105 - 119 LIGHT GREEN
120 - 127 LIGHT YELLOW
128 - 189 CLOCKWISE ROTATION FAST - SLOW
190 - 193 STOP
194 - 255 COUNTER-CLOCKWISE ROTATION
SLOW - FAST
4 GOBOS
0 - 9 OPEN
10 - 18 GOBO 1
19 - 27 GOBO 2
28 - 36 GOBO 3
37 - 46 GOBO 4
47 - 55 GOBO 5
56 - 63 GOBO 6
64 - 73 OPEN SHAKE
74 - 82 GOBO 1 SHAKE
83 - 91 GOBO 2 SHAKE
92 - 100 GOBO 3 SHAKE
101 - 110 GOBO 4 SHAKE
111 - 119 GOBO 5 SHAKE
120 - 127 GOBO 6 SHAKE
128 - 189 CLOCKWISE ROTATION FAST - SLOW
190 - 193 STOP
194 - 255 COUNTER-CLOCKWISE ROTATION
SLOW - FAST
ADJ Products, LLC - www.adj.com - Focus Spot Two Instruction Manual Page 12 ADJ Products, LLC - www.adj.com - Focus Spot Two Instruction Manual Page 13
Page 8
Focus Spot Two 16 Channel Mode
Focus Spot Two 16 Channel Mode
Channel Value Function
5 GOBO ROTATION
0 - 127 INDEXING
128 - 189 CLOCKWISE ROTATION FAST - SLOW
190 - 193 STOP
194 - 255 COUNTER-CLOCKWISE ROTATION
SLOW - FAST
6 PRISM
0 - 7 NO EFFECT
8 - 255 PRISM EFFECT
7 STROBE/SHUTTER
0 - 7 OFF
8 - 15 OPEN
16 - 131 STROBING SLOW - FAST
132 - 139 OPEN
140 - 181 SLOW OPEN - FAST CLOSE
182 - 189 OPEN
190 - 231 FAST OPEN - SLOW CLOSE
232 - 239 OPEN
240 - 247 RANDOM STROBE SLOW - FAST
248 - 255 OPEN
8 0 - 255 MASTER DIMMER 0% - 100%
9 UV STROBE/SHUTTER
0 - 7 OFF
8 - 15 OPEN
16 - 131 STROBING SLOW - FAST
132 - 139 OPEN
140 - 181 SLOW OPEN - FAST CLOSE
182 - 189 OPEN
190 - 231 FAST OPEN - SLOW CLOSE
232 - 239 OPEN
240 - 247 RANDOM STROBE SLOW - FAST
248 - 255 OPEN
10 0 - 255 UV MASTER DIMMER 0% - 100%
11 0 - 255 FOCUS 0%- 100%
Channel Value Function
12 SHOW
0 OFF
1 - 21 SHOW 1
22 - 41 SHOW 2
42 - 61 SHOW 3
62 - 81 SHOW 4
82 - 255 SHOW 0 (RANDOM SHOW)
13 0 - 255 SHOW SPEED FAST - SLOW
14 DIMMER MODES
0 - 20 STANDARD
21 - 40 STAGE
41 - 60 TV
61 - 80 ARCHITECTURAL
81 - 100 THEATRE
101 - 255 DEFAULT TO UNIT
15 0 - 255 PAN/TILT SPEED FAST - SLOW
16 FUNCTION
0 - 69 NOTHING
70 - 79 BLACKOUT WITH PAN/TILT
80 - 89 NOTHING
90 - 99 BLACKOUT WITH COLOR CHANGE
100 - 109 NOTHING
110 - 119 BLACKOUT WITH GOBO CHANGE
120 - 129 NOTHING
130 - 139 ENABLE SPLIT COLORS
140 - 209 RESET ALL
210 - 249 NOTHING
250 - 255 SOUND ACTIVE
GOBO 1 GOBO 2 GOBO 3
GOBO 4 GOBO 5 GOBO 6
ADJ Products, LLC - www.adj.com - Focus Spot Two Instruction Manual Page 15ADJ Products, LLC - www.adj.com - Focus Spot Two Instruction Manual Page 14
Page 9
Focus Spot Two 18 Channel Mode
Focus Spot Two 18 Channel Mode
Channel Value Function
1 0 - 255 PAN MOVEMENT 0° - 630°
2 0 - 255 PAN FINE 0% - 100%
3 0 - 255 TILT MOVEMENT 0° - 230°
4 0 - 255 TILT FINE 0% - 100%
5 COLOR
0 - 14 WHITE
15 - 29 RED
30 - 44 BLUE
45 - 59 GREEN
60 - 74 YELLOW
75 - 89 PINK
90 - 104 LIGHT BLUE
105 - 119 LIGHT GREEN
120 - 127 LIGHT YELLOW
128 - 189 CLOCKWISE ROTATION FAST - SLOW
190 - 193 STOP
194 - 255 COUNTER-CLOCKWISE ROTATION
SLOW - FAST
6 GOBOS
0 - 9 OPEN
10 - 18 GOBO 1
19 - 27 GOBO 2
28 - 36 GOBO 3
37 - 46 GOBO 4
47 - 55 GOBO 5
56 - 63 GOBO 6
64 - 73 OPEN SHAKE
74 - 82 GOBO 1 SHAKE
83 - 91 GOBO 2 SHAKE
92 - 100 GOBO 3 SHAKE
101 - 110 GOBO 4 SHAKE
111 - 119 GOBO 5 SHAKE
120 - 127 GOBO 6 SHAKE
128 - 189 CLOCKWISE ROTATION FAST - SLOW
190 - 193 STOP
194 - 255 COUNTER-CLOCKWISE ROTATION
SLOW - FAST
Channel Value Function
7 GOBO ROTATION
0 - 127 INDEXING
128 - 189 CLOCKWISE ROTATION FAST - SLOW
190 - 193 STOP
194 - 255 COUNTER-CLOCKWISE ROTATION
SLOW - FAST
8 PRISM
0 - 7 NO EFFECT
8 - 255 PRISM EFFECT
9 STROBE/SHUTTER
0 - 7 OFF
8 - 15 OPEN
16 - 131 STROBING SLOW - FAST
132 - 139 OPEN
140 - 181 SLOW OPEN - FAST CLOSE
182 - 189 OPEN
190 - 231 FAST OPEN - SLOW CLOSE
232 - 239 OPEN
240 - 247 RANDOM STROBE SLOW - FAST
248 - 255 OPEN
10 0 - 255 MASTER DIMMER 0% - 100%
11 UV STROBE/SHUTTER
0 - 7 OFF
8 - 15 OPEN
16 - 131 STROBING SLOW - FAST
132 - 139 OPEN
140 - 181 SLOW OPEN - FAST CLOSE
182 - 189 OPEN
190 - 231 FAST OPEN - SLOW CLOSE
232 - 239 OPEN
240 - 247 RANDOM STROBE SLOW - FAST
248 - 255 OPEN
12 0 - 255 UV MASTER DIMMER 0% - 100%
13 0 - 255 FOCUS 0%- 100%
ADJ Products, LLC - www.adj.com - Focus Spot Two Instruction Manual Page 16 ADJ Products, LLC - www.adj.com - Focus Spot Two Instruction Manual Page 17
Page 10
Focus Spot Two 18 Channel Mode
Channel Value Function
14 SHOW
0 OFF
1 - 21 SHOW 1
22 - 41 SHOW 2
42 - 61 SHOW 3
62 - 81 SHOW 4
82 - 255 SHOW 0 (RANDOM SHOW)
15 0 - 255 SHOW SPEED FAST - SLOW
16 DIMMER MODES
0 - 20 STANDARD
22 - 40 STAGE
41 - 60 TV
61 - 80 ARCHITECTURAL
81 - 100 THEATRE
101 - 255 DEFAULT TO UNIT
17 0 - 255 PAN/TILT SPEED FAST - SLOW
18 FUNCTION
0 - 69 NOTHING
70 - 79 BLACKOUT WITH PAN/TILT
80 - 89 NOTHING
90 - 99 BLACKOUT WITH COLOR CHANGE
100 - 109 NOTHING
110 - 119 BLACKOUT WITH GOBO CHANGE
120 - 129 NOTHING
130 - 139 ENABLE SPLIT COLORS
140 - 209 RESET ALL
210 - 249 NOTHING
250 - 255 SOUND ACTIVE
Focus Spot Two System Menu
GOBO 1 GOBO 2 GOBO 3
GOBO 4 GOBO 5 GOBO 6
ADJ Products, LLC - www.adj.com - Focus Spot Two Instruction Manual Page 18 ADJ Products, LLC - www.adj.com - Focus Spot Two Instruction Manual Page 19
Page 11
Focus Spot Two System Menu
Focus Spot Two System Menu
System Menu: When making adjustments press ENTER to
conrm your setup then press and hold the MENU button
for at least 3 seconds. To exit without making any adjust-
ments press the MENU button. The display will lock after 30
seconds, press the MENU button for 3 seconds to unlock.
DMX Address - Set the DMX Address -
1. Press the MENU button until “DMX Addresss” is displayed, press
ENTER.
2. “X” will now be displayed, “X” represents the displayed address.
Press the UP or DOWN buttons to nd your desired address.
3. Press ENTER to conrm, and then press and hold the MENU button
for at least three seconds to assign.
Channel Mode - This will let you select your desired
DMX Channel mode.
1. Press the MENU button until “Channel Mode” is displayed, press
ENTER.
2. “X Chan” will now be displayed, “X” represents the displayed DMX
channel mode. Press the UP or DOWN buttons to nd your desired
Channel mode.
3. Press ENTER to conrm.
Show Mode - Show modes 0-4 (Factory programs).
Show mode can run with or without sound active mode
active.
1. Press the MENU button until “Show Mode” is displayed, press
ENTER.
2. “Show X” will now be displayed, “X” representing a number between
0-4. Shows 1-4 are factory programs, while show “0” is random mode.
Use the UP or DOWN buttons to nd your desired show.
3. When you have found your desired show press ENTER, then press
and hold the MENU button for at least 3 seconds to activate.
Sound Mode - In this mode the unit will run in sound
active mode.
1. Press the MENU button until “Sound Mode” is displayed, press
ENTER.
2. Either “On” or “O” will now be displayed. Use the UP or DOWN
buttons to toggle between “On” and “O”.
3. Press ENTER to conrm your selection, the press and hold the
MENU button to activate.
Sound Sense - In this mode you can adjust the sound
sensitivity of the sound active mode.
Slave Mode - This will let you set unit as a master or
slave in a master/slave conguration.
1. Press the MENU button until “Slave Mode” is displayed, press
ENTER. Either “Master”, “Slave 1” or “Slave 2” will be displayed.
2. Press the UP or DOWN buttons until your desired setting is displayed, then press ENTER to conm.
NOTE: In a Master/Slave conguration you can make one xture the
Master and then set the next xture to “Slave 2”, the xtures will now
have contrast movement to each other.
ADJ Products, LLC - www.adj.com - Focus Spot Two Instruction Manual Page 20 ADJ Products, LLC - www.adj.com - Focus Spot Two Instruction Manual Page 21
1. Press the MENU button until “Sound Sense” is displayed, press
ENTER.
2. Press the UP or DOWN buttons to adjust the sensitivity level. The
sensitivity level can be adjusted between 0 (the lowest) and 100 (most
sensitive).
3. Press ENTER to set you desired level.
Page 12
Focus Spot Two System Menu
Focus Spot Two System Menu
DMX State - This mode can be used as a precaution
mode, that in case the DMX signal is lost, the operating mode
chosen in the setup is the running mode the xture will go
into when the DMX signal is lost. You can also set this as
the operating mode you would like the unit to return to when
power is applied.
1. Press the MENU button until “DMX State” is displayed, press ENTER.
2. Either “Master Slave”, “Blackout”, or “Last State” will be displayed.
Choose an operating mode you would like the unit to start up in when
power is applied or the DMX signal is lost.
• Master Slave - If the DMX signal is lost or power is applied, the unit
will automatically go into Master Slave mode.
• Blackout - If the DMX signal is lost or power is applied, the unit will
automatically go into stand by mode.
• Last State - If the DMX signal is lost the xture will stay in the last
DMX set up. If power is applied and this mode is set, the unit will automatically go into the last DMX set up.
3. Press ENTER to conrm your desired set up.
Dimmer Curve - In this mode you can select the dimmer
curve.
Pan Invert - Pan Inversion
1. Press the MENU button until “Pan Invert” is displayed, press
ENTER. Either “Yes” or “No” will be displayed.
2. To activate the Pan inversion press the UP or DOWN buttons until
“Yes” is displayed, press ENTER to conm. To deactivate Pan inversion, select “No” and press Enter.
Tilt Invert - Tilt Inversion
1. Press the MENU button until “Tilt Invert” is displayed, press
ENTER. Either “Yes” or “No” will be displayed.
2. To activate the Tilt inversion press the UP or DOWN buttons until
“Yes” is displayed, press ENTER to conm. To deactivate Tilt inversion, select “No” and press Enter.
Back Light - With this function you can make the back-
light automatically turn off after one minute.
1. Press the MENU button until “Back Light” is displayed, press ENTER.
2. Either “On” or “O” will now be displayed. Press the UP or DOWN
buttons to select “On” to keep the backlight on at all times, or “O” to
allow the backlight to turn o after 1 minute. Press any button to turn
the backlight on again.
1. Press the MENU button until “Dimmer Curve” is displayed, press
ENTER.
2. The current dimmer curve setting will be displayed.
3. Press the UP or DOWN buttons to nd your desired dimmer curve
and press ENTER to conrm. See the Dimmer Curve Chart on page 32
for the dierent settings.
Auto Test - This function will run a self test program.
1. Press the MENU button until “Auto Test” is displayed, press
ENTER.
2. The xture will now run a self test. Press the MENU button to exit.
LED Temp. - With this function you can display the run-
ning temperature of the unit.
1. Press the MENU button until “LED Temp.” is displayed, press
ENTER.
ADJ Products, LLC - www.adj.com - Focus Spot Two Instruction Manual Page 23ADJ Products, LLC - www.adj.com - Focus Spot Two Instruction Manual Page 22
Page 13
Focus Spot Two System Menu
2. The current running temperature of the xture will now be displayed. Press MENU to exit.
Fixture Time - With this function you can display the
running time of the unit.
1. Press the MENU button until “Fixture Time” is displayed, press
ENTER.
2. The running time of the xture will now be displayed. Press MENU
to exit.
Firmware Version - This will display the rmware/soft-
ware version
1. Press the MENU button until “Firmware Version” is displayed. Press
the ENTER button and the software vesion will be displayed.
2. Press the MENU button to leave this function.
Focus Spot Two Home Adjustment Menu
To enter the Oset Menu, press the MENU button to unlock the display, then press the ENTER button for at least 5 seconds. In this submenu you are able to adjust the home position of the pan, tilt, focus,
prism, rotating gobo motor, gobo wheel, and color wheel. To exit this
menu press and hold the MENU button.
Pro Default - Restore the factory settings
1. Press the MENU button until “Pro Default” is displayed, press
ENTER. Either “On” or “O” will be displayed.
2. To restore the settings press the UP or DOWN buttons until “On” is
displayed, press ENTER to conm.
Pan Oset - Adjustment of the pan home position.
1. Press the ENTER button for at least 5 seconds, then press the UP
or DOWN buttons so that “Pan Offset” is displayed, press ENTER.
2. Use the UP and DOWN buttons to make your adjustments, and
then press ENTER to conrm. Press the MENU button for one second
to exit.
Reset - Use this function to reset the motors.
1. Press the MENU button until “Reset” is displayed, press ENTER.
ENTER. Either “No” or “Yes” will be displayed.
2. To reset the xture select “Yes” and press ENTER to conrm. The
xture will now begin to reset.
Tilt Oset - Adjustment of the tilt home position.
1. Press the ENTER button for at least 5 seconds, then press the UP
or DOWN buttons so that “Tilt Offset” is displayed, press ENTER.
2. Use the UP and DOWN buttons to make your adjustments, and
then press ENTER to conrm. Press the MENU button for one second
to exit.
Focus Oset - Setting adjustment for the focus.
1. Press the ENTER button for at least 3 seconds, then press the UP
or DOWN buttons so that “Focus Offset” is displayed, press ENTER.
ADJ Products, LLC - www.adj.com - Focus Spot Two Instruction Manual Page 24 ADJ Products, LLC - www.adj.com - Focus Spot Two Instruction Manual Page 25
Page 14
Focus Spot Two Home Adjustment Menu
Focus Spot Two Operation
2. Use the UP and DOWN buttons to make your adjustments, and
then press ENTER to conrm. Press the MENU button for one second
to exit.
Prism Oset - Setting adjustment for the prism.
1. Press the ENTER button for at least 5 seconds, then press the UP
or DOWN buttons so that “Prism Offset” is displayed, press ENTER.
2. Use the UP and DOWN buttons to make your adjustments, and
then press ENTER to conrm. Press the MENU button for one second
to exit.
Rgobo Oset - Setting adjustment for the rotating
gobo motor.
1. Press the ENTER button for at least 5 seconds, then press the
UP or DOWN buttons so that “Rgobo Offset” is displayed, press
ENTER.
2. Use the UP and DOWN buttons to make your adjustments, and
then press ENTER to conrm. Press the MENU button for one second
to exit.
Gobo Oset - Setting adjustment for the gobo wheel.
1. Press the ENTER button for at least 5 seconds, then press the UP
or DOWN buttons so that “Gobo Offset” is displayed, press ENTER.
2. Use the UP and DOWN buttons to make your adjustments, and
then press ENTER to conrm. Press the MENU button for one second
to exit.
Color Oset - Setting adjustment for the color wheel.
1. Press the ENTER button for at least 5 seconds, then press the UP
or DOWN buttons so that “Color Offset” is displayed, press ENTER.
2. Use the UP and DOWN buttons to make your adjustments, and
then press ENTER to conrm. Press the MENU button for one second
to exit.
Universal DMX Control: This function allows you to use a univer-
sal DMX-512 controller to control the pan, tilt, gobos, colors, focusing, dimmer and strobe. A DMX controller allows you to create unique
programs tailored to your individual needs.
1. The Focus Spot Two has 2 DMX channel modes; 15 channel
mode and 17 channel mode. See pages 13-18 for detailed
description of the DMX values and traits.
2. To control your fixture in DMX mode, follow the set-up procedures
on pages 10-12 as well as the set-up specifications that are
included with your DMX controller.
3. Use the controller’s faders to control the various DMX fixture traits.
4. This will allow you to create your own programs.
5. Follow the instructions on page 20 to select your desired DMX
channel mode and to set the DMX address.
6. For longer cable runs (more than a 100 feet) use a terminator on
the last fixture.
7. For help operating in DMX mode consult the manual included
with your DMX controller.
Sound Active Mode: This mode allows either single unit or several
units linked together, to run to the beat of the music.
1. Press the MENU button until “Sound State” is displayed, and
press ENTER. Press the UP or DOWN buttons so that “ON” is dis played and press ENTER.
2. Press the MENU button until “Sound Sense” is displayed, and
press ENTER. Use the UP and DOWN buttons to adjust the sound
sensitivity. Press ENTER when you have found your desired sensi-
tivity level.
Show Mode: This mode allows either a single unit or several units
linked together, to run one of four shows that you choose.
1. Press the MENU button until “Show Mode” is displayed, and
press ENTER.
2. Press the UP or DOWN buttons to nd your desired show, and
press ENTER.
ADJ Products, LLC - www.adj.com - Focus Spot Two Instruction Manual Page 26 ADJ Products, LLC - www.adj.com - Focus Spot Two Instruction Manual Page 27
Page 15
Focus Spot Two Master-Slave Set Up
Focus Spot Two Remote Operation
Master-Slave Operation This function will allow you to link up to 16
units together and operate without a controller. The units will be sound
activated. In Master-Slave operation one unit will act as the controlling
unit and the others will react to the controlling units programs. Any unit
can act as a Master or as a Slave.
1. Using approved DMX data cables, daisy chain your units togeth-
er via the XLR connector on the rear of the units. Remember the
Male XLR connector is the input and the Female XLR connector
is the output. The rst unit in the chain (master) will use the female
XLR connector only - The last unit in the chain will use the male
XLR connector only. For longer cable runs we suggest a termina tor at the last fixture.
2. On the Master unit press the MENU button until “Slave Mode” is
displayed, and press ENTER. Use the UP and DOWN buttons to
scroll to the “Master” setting and press ENTER.
3. After setting the Master unit to the master setting find and set
your desired operating mode.
4. On the slave units press the MENU button until “Slave Mode” is
displayed, and press ENTER. Choose either “Slave 1” or “Slave
2” and press ENTER.
5. The slave units will now follow the Master unit.
Focus Spot Two Manual Focus
The focus can be adjusted under DMX control. It can also be manually focused using the focus wheel located on the bottom front of the
moving head. Rotate the focus wheel back and forth until you get your
perfect focus. This wheel can be used in conjunction with the focus
channel in DMX mode as well.
Focus Spot Two Power Cord Daisy Chain
With this feature you can connect the xtures to one another
using the PowerCon input and output sockets. The quantity that
can be connected is 14 xtures maximum @ 120V and 26 xtures
maximum @ 230V. After you have reached the maximum amount
of xtures you will need to use a new power outlet. They must be
the same xtures. DO NOT mix xtures.
The UC IR (sold separately) infrared remote gives you control of
various functions (See below). To control the fixture you must aim the
remote at the front of the fixture and be no more than 30 feet away.
The Airstream IR (sold separately) remote transmitter plugs into
the headphone jack of your iOS phone or tablet. To control your IR
fixture you must raise the volume to the maximum on your iOS phone
or tablet and aim the transmitter at the fixture sensor and be no more
than 15 feet away. After you have purchased the Airstream IR transmitters, the app is a free download from the app store for your iOS
phone or tablet. The app comes with 3 pages of control depending
on the fixture you are using. Please see below for IR functions. This
unit works with App page 1.
STAND BY - Pressing this button will blackout the fixture.
FULL ON - Hold this button down to fully light up the unit. When you
let the button go, the unit will return to its previous state.
FADE/GOBO - Press this button once to access gobo wheel. Use
the number buttons to find your desired gobo.
“DIMMER +” and “DIMMER -” - Use these buttons to adjust the output intensity in Color mode.
STROBE - This button will activate the strobe effect. Press and hold
this button to activate strobing and release the button to stop strob-
ing.
COLOR - Press this button to access the color wheel. Use the num-
ber buttons to select your desired color. Adjust the output intensity
using the “DIMMER +” and “DIMMER -” buttons.
1-9 - In color mode and gobo mode, these buttons will allow you to
select a desired color or gobo. In show mode buttons 1-4 will let you
select your desired show.
SOUND ON & OFF - These buttons activate and deactivate the
sound active mode.
SHOW - This activates the show mode. Use buttons 1-4 to select
your desired show.
ADJ Products, LLC - www.adj.com - Focus Spot Two Instruction Manual Page 28
ADJ Products, LLC - www.adj.com - Focus Spot Two Instruction Manual Page 29
Page 16
Focus Spot Two Changing the Gobo
The gobo’s in this unit are interchangable. Please be very careful when replacing the gobo.
Caution! Never open the unit when in use. Always disconnect
the main power before attempting to change the gobos.
1. To change a gobo, rotate the moving head so that the UV
lens is located on top. Unscrew the single middle screw. See
instruction number 1 on the next page.
2. Once you loosen the single screw you are able to swing the
head back. See instruction number 2 on the next page. You
will now be able to access the gobo wheel. Turn the wheel
with your hand until you come across the gobo you would
like to change.
3. To remove the gobo holder gently pull the gobo holder to-
wards the front of the unit and slide it up and out.
4. Gently and carefully remove the retainer ring. After the re-
tainer ring is removed, carefully remove the gobo.
5. Change the gobo and replace the retainer ring. Carefully slide
the gobo holder back into the housing slot.
Focus Spot Two Removing the Head Casing
Sc re w
1. Unscrew the single screw 2. Flip the top cover back
Sc rew
6. Reassemble the unit.
3. Remove the lens
4. Unscrew the 4 screws
located on the other side
ADJ Products, LLC - www.adj.com - Focus Spot Two Instruction Manual Page 30 ADJ Products, LLC - www.adj.com - Focus Spot Two Instruction Manual Page 31
Page 17
Focus Spot Two Photometric Chart
Focus Spot Two Fuse Replacement
W
Lux
Lux
Distance(m)
Diameter(m)15°
Diameter(m)20°
34410 8370 3790 2090
25700 6240 2780 1530W
0.317
0.389
1
2
0.634
0.778
0.95
1.166
3
°
15
4
20
1.267
1.555
°
1300
950
5
1.584
1.944
Focus Spot Two Dimmer Curve Chart
Locate and remove the unit’s PowerCon cord. Once the cord has been
removed the fuse holder is located under the power socket. Use a philips head screw driver unscrew the fuse holder. Remove the bad fuse
and replace with a new one.
Focus Spot Two Cleaning
Due to fog residue, smoke, and dust cleaning the internal and external optical lenses and mirror should be carried out periodically to
optimize light output. Cleaning frequency depends on the environment in which the fixture operates (I.e. smoke, fog residue, dust,
dew). In heavy club use we recommend cleaning on a monthly basis.
Periodic cleaning will ensure longevity, and crisp output.
1. Use normal glass cleaner and a soft cloth to wipe down the out-
side casing.
2. Use a brush to wipe down the cooling vents and fan grill.
3. Clean the external optics with glass cleaner and a soft cloth every
20 days.
4. Clean the internal optics with glass cleaner and a soft cloth every
30-60 days.
5. Always be sure to dry all parts completely before plugging the unit
back in.
Focus Spot Two Trouble Shooting
Trouble Shooting: Listed below are a few common problems that
you may encounter, with solutions.
Ramp Effect
Standard
Stage
TV
Architectural
Theatre
(Fade Time) (Fade Time)
No light output from the unit;
1. Be sure the external fuse has not blown. The fuse is located on
the rear panel of the unit.
2. Be sure the fuse holder is completely and properly seated.
Unit does not respond to sound;
1. Low frequencies (bass) should cause the unit to react to sound.
Tapping on the microphone, quiet or high pitched sounds may
not activate the unit.
ADJ Products, LLC - www.adj.com - Focus Spot Two Instruction Manual Page 32 ADJ Products, LLC - www.adj.com - Focus Spot Two Instruction Manual Page 33
Page 18
Focus Spot Two Warranty
MANUFACTURER’S LIMITED WARRANTY
A. ADJ Products, LLC hereby warrants, to the original purchaser, ADJ Products, LLC products
to be free of manufacturing defects in material and workmanship for a prescribed period from
the date of purchase (see specific warranty period on reverse). This warranty shall be valid only if the
product is purchased within the United States of America, including possessions and
territories. It is the owner ’s responsibility to establish the date and place of purchase by acceptable
evidence, at the time service is sought.
B. For warranty service you must obtain a Return Authorization number (RA#)
before sending back the product–please contact ADJ Products, LLC Service Department
at 800-322-6337. Send the product only to the ADJ Products, LLC factory. All
shipping charges must be pre-paid. If the requested repairs or service (including
parts replacement) are within the terms of this warranty, ADJ Products, LLC will pay return
shipping charges only to a designated point within the United States. If the entire instrument is
sent, it must be shipped in it’s original package. No accessories should be shipped with the product. If
any accessories are shipped with the product, ADJ Products, LLC shall have no liability whatsoever for
loss of or damage to any such accessories, nor for the safe return thereof.
C. This warranty is void if the serial number has been altered or removed; if the product is modified in any
manner which ADJ Products, LLC concludes, after inspection, affects the reliability of the product; if the
product has been repaired or serviced by anyone other than the ADJ Products, LLC factory unless prior
written authorization was issued to purchaser by ADJ Products, LLC; if the product is damaged because
not properly maintained as set forth in the instruction manual.
D. This is not a service contract, and this warranty does not include maintnance, cleaning or periodic check
up. During the period specified above, ADJ Products, LLC will replace defective parts at its expense
with new or refurbished parts, and will absorb all expenses for warranty service and repair labor by
reason of defects in material or workmanship. The sole responsibility of ADJ Products, LLC under this
warranty shall be limited to the repair of the product, or replacement thereof, including parts, at the sole
discretion of ADJ Products, LLC. All products covered by this warranty were manufactured after August
15, 2012, and bear indentifying marks to that effect.
E. ADJ Products, LLC reserves the right to make changes in design and/or improvements upon its products
without any obligation to include these changes in any products theretofore manufactured.
No warranty, whether expressed or implied, is given or made with respect to any accessory supplied with
products described above. Except to the extent prohibited by applicable law, all implied warranties made
by ADJ Products, LLC in connection with this product, including warranties of merchantability or fitness,
are limited in duration to the warranty period set forth above. And no warranties, whether expressed or
implied, including warranties of merchantability or fitness, shall apply to this product after said period
has expired. The consumer’s and/or Dealer’s sole remedy shall be such repair or replacement as is
expressly provided above; and under no circumstances shall ADJ Products, LLC be liable for any loss or
damage, direct or consequential, arising out of the use of, or inability to use, this product.
This warranty is the only written warranty applicable to ADJ Products, LLC Products and
supersedes all prior warranties and written descriptions of warranty terms and conditions heretofore
published.
MANUFACTURER’S LIMITED WARRANTY PERIODS:
•NonL.E.D.LightingProducts=1-year(365days)LimitedWarranty(Such as: Special Effect
Lighting, Intelligent Lighting, UV lighting, Strobes, Fog Machines, Bubble Machines, Mirror Balls, Par
Cans, Trussing, Lighting Stands etc. excluding LED and lamps)
•LaserProducts=1Year(365Days)LimitedWarranty(excluding laser diodes which have a 6 month
limited warranty)
•L.E.D.Products=2-year(730days)LimitedWarranty(excluding batteries which have a 180 day lim-
ited warranty). Note:2YearWarrantyonlyappliestopurchaseswithintheUnitedStates.
•StarTecSeries=1YearLimitedWarranty(excluding batteries which have a 180 day limited war-
ranty).
•ADJDMXControllers=2Year(730Days)LimitedWarranty
ADJ Products, LLC - www.adj.com - Focus Spot Two Instruction Manual Page 34
Focus Spot Two Specifications
Model: Focus Spot Two
Voltage: 100 - 240V, 50/60Hz
LED: 1 x 75W Cold White LED
1 x 3W UV LED
Wavelength: 399~427nm
Power Consumption: 108W
Dimensions: 6.75”(L) x 9.25”(W) x 15.25”(H)
173mm x 237mm x 385mm
Weight: 16 Lbs. / 7.3 kgs.
Beam Angle: 15 ~ 20 Degrees
Gobo Size: 23.8mm (Outer)
19mm (Inner/Image)
0.2mm (Thickness)
Fuse: 2 Amp
Power Cord Daisy Chain: 14 Fixtures Max. (120V)
26 Fixtures Max. (230V)
Duty Cycle: None
DMX: 2 DMX Channel Modes: 16 Channel
Mode & 18 Channel Mode
Sound Active: Ye s
Working Position: Any Safe, Secure Position
Warranty: 2 Year (730 days)
Please Note: Specications and improvements in the design
of this unit and this manual are subject to change without any
prior written notice.
ADJ Products, LLC
6122 S. Eastern Ave. Los Angeles, CA 90040 USA
Tel: 323-582-2650 / Fax: 323-725-6100
Web: www.adj.com / E-mail: info@americandj.com
A.D.J. Supply Europe B.V.
Junostraat 2
6468 EW Kerkrade
The Netherlands
service@adjgroup.eu / www.adj.eu
Tel: +31 45 546 85 00 / Fax: +31 45 546 85 99
Loading...