ADJ Focus Beam LED User guide

FOCUS BEAM LED

User Instructions

©2019 ADJ Products, LLC all rights reserved. Information, specications, diagrams, images, and

FCC STATEMENT
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.

FCC RADIO FREQUENCY INTERFERENCE WARNINGS & INSTRUCTIONS
This product has been tested and found to comply with the limits as per Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful interference in a residential installation.
This device uses and can radiate radio frequency energy and, if not installed and used in accordance with
the included instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this device does cause harmful
interference to radio or television reception, which can be determined by turning the device off and on, the
user is encouraged to try to correct the interference by one or more of the following methods:

· Reorient or relocate the device.

· Increase the separation between the device and the receiver.

· Connect the device to an electrical outlet on a circuit different from which the radio receiver is
connected.

· Consult the dealer or an experienced radio/TV technician for help.

instructions herein are subject to change without notice. ADJ Products, LLC logo and identifying
product names and numbers herein are trademarks of ADJ Products, LLC. Copyright protection
claimed includes all forms and matters of copyrightable materials and information now allowed by
statutory or judicial law or hereinafter granted. Product names used in this document may be
trademarks or registered trademarks of their respective companies and are hereby acknowledged.
All non-ADJ Products, LLC brands and product names are trademarks or registered trademarks of

their respective companies.

ADJ Products, LLC and all aliated companies hereby disclaim any and all liabilities for property,
equipment, building, and electrical damages, injuries to any persons, and direct or indirect economic
loss associated with the use or reliance of any information contained within this document, and/or as
a result of the improper, unsafe, unsucient and negligent assembly, installation, rigging, and operation
of this product.

DOCUMENT VERSION

Due to additional product features and/or enhancements, an updated version of this document
may be available online.
Please check www.adj.com for the latest revision/update of this manual before beginning
installation and/or programming.

Date

07/02/19

09/26/19

10/31/19

Europe Energy Saving Notice
Energy Saving Matters (EuP 2009/125/EC)

Saving electric energy is a key to help protecting the enviroment. Please turn o all electrical prod­ucts when they are not in use. To avoid power consumption in idle mode, disconnect all electrical

equipment from power when not in use. Thank you!

Document
Version

1

1.2 N/C

2 1.0.4

Software
Version >

1.0.2

DMX Channel Mode

16 / 18 Initial Version

N/C 3-Pin DMX Updated to 5-Pin

N/C

Notes

“Reset All” Added to DMX Modes
Pan Degree Selection Added
Gamma Removed, Dimming Curves Added

Focus Beam LED Table of Contents

Introduction
Features I Warranty Registration

Safety Precautions
Overview

Installation

DMX Set Up

DMX Addressing
DMX Modes & Values

System Menu
Master-Slave Set Up

Dimmer Mode Chart I Dimmer Curve Chart

3
4
5
7
8

9
11
12
17
23
24

Static Gobos I Dimensional Drawings
Fuse Replacement I Multiple Unit Power Linking
Trouble Shooting I Cleaning
Limited Warranty (USA Only)
Technical Specications

25
26
26
27
28

ADJ Products, LLC - www.adj.com - Focus Beam LED User Manual Page 2

Focus Beam LED Introduction

Unpacking: Thank you for purchasing the Focus Beam LED by ADJ Products, LLC. Every unit has
been thoroughly tested and has been shipped in perfect operating condition. Carefully check the ship­ping carton for damage that may have occurred during shipping. If the carton appears to be damaged,
carefully inspect your xture for any damage and be sure all accessories necessary to operate the unit
has arrived intact. In the case damage has been found or parts are missing, please contact our toll free
customer support number for further instructions. Do not return this unit to your dealer without rst

contacting customer support.

Introduction: The Focus Beam LED is a DMX intelligent, moviing head, LED fixture. This xture can be
used in a stand alone mode or connected in a Master/Slave conguration. The fixture comes equipped
with 2 prisms (8 facet circular & 6 facet linear), focus, frost, 6 different dimming options with dimming
speed control. The Focus Beam LED has 2 DMX channel modes; 16 & 18.

This product is intended to be used by professionally trained personnel only and is not suitable
for private use.

Customer Support: Contact ADJ Service for any product related service and support needs. Also visit

https://forums.adj.com/ with questions, comments or suggestions.

Parts: To purchase parts online visit http://parts.americandj.com

ADJ SERVICE USA - Monday - Friday 8:00am to 4:30pm PST
Voice: 800-322-6337 | Fax: [phone] | [e-mail]

ADJ SERVICE EUROPE - Monday - Friday 08:30 to 17:00 CET
Voice: [phone] | Fax: [phone] | [e-mail]

ADJ PRODUCTS LLC USA

6122 S. Eastern Ave. Los Angeles, CA. 90040
323-582-2650 | Fax [phone] | www.adj.com | [e-mail]

ADJ SUPPLY Europe B.V

Junostraat 2 6468 EW Kerkrade, The Netherlands
[phone] | Fax [phone]

www.adj.eu | [e-mail]

ADJ PRODUCTS GROUP Mexico

AV Santa Ana 30 Parque Industrial Lerma, Lerma, Mexico 52000

[phone]

Caution! There are no user serviceable parts inside this unit. Do not attempt any repairs yourself,
doing so will void your manufactures warranty. In the unlikely event your unit may require service
please contact ADJ Products, LLC.

PLEASE recycle the shipping carton when ever possible.

ADJ Products, LLC - www.adj.com - Focus Beam LED User Manual Page 3

Focus Beam LED Features

• Individual Color and Gobo Wheels

• 13 Colors + White & Split Colors

• 14 Gobos + Open

• Electronic Dimming 0-100%

• DMX-512 protocol

• 3-Pin DMX Connections (Updated to 5-Pin DMX Connections 9/26/19)

• 2 DMX Channel Modes: 16 / 18

• Multiple Unit Power Linking (See page 25)

Included:
1 x powerCON Cable
1 x Safety Cable
2 x Omega Clamps

Focus Beam LED Warranty Registration

The Focus Beam LED carries a 2 year limited warranty. Please fill out the enclosed warranty card to
validate your purchase. All returned service items whether under warranty or not, must be freight pre­paid and accompany a return authorization (R.A.) number. The R.A. number must be clearly written on
the outside of the return package. A brief description of the problem as well as the R.A. number must
also be written down on a piece of paper included in the shipping carton. If the unit is under warranty,
you must provide a copy of your proof of purchase invoice. You may obtain a R.A. number by con­tacting our customer support team on our customer support number. All packages returned to the
service department not displaying a R.A. number on the outside of the package will be returned to the

shipper.

ADJ Products, LLC - www.adj.com - Focus Beam LED User Manual Page 4

Focus Beam LED Safety Precautions

• DO NOT TOUCH the xture housing during operation. Turn OFF the power and allow approximately
15 minutes for the xture to cool down before servicing.

• DO NOT shake the xture, avoid brute force when installing and/or operating the xture.

• DO NOT operate the xture if the power cord has become frayed, crimped and/or damaged. If the

power cord is damaged, replace immediately with a new one of similar power rating.

• DO NOT Do not attempt to remove or break o the ground prong from the electrical cord. This
prong is used to reduce the risk of electrical shock and re in case of an internal short.

• DO NOT attempt to operate this unit, if it becomes damaged.

• DO NOT spill water or other liquids into or on to your unit.

• This unit is intended for indoor use only, use of this product outdoors voids all warranties.

• To reduce the risk of electrical shock or re, do not expose this unit rain or moisture

• Disconnect from main power before making any type of connection.

• DO NOT block any air ventilation slots. All fan and air inlets must remain clean and never blocked.
Allow approx. 6” (15cm) between xture and other devices or a wall for proper cooling.

• Always be sure to mount this unit in an area that will allow proper ventilation. Allow about 6”
(15cm) between this device and a wall.

• During the initial operation of this xture, a light smoke or smell may emit from the interior of the
xture. Thsi is a normal process and is caused by excess paint in the interior of the casing burning
o from the heat. This will decrease gradually over time.

• DO NOT remove the cover under any conditions. There are no user serviceable parts inside.

• When installing xture in a suspended enviroment, always use mounting hardware that is no less
than M10 x 25mm, and always install xture with an appropriately rated safety cable.

• Never operate this unit when it’s cover is removed.

• Never plug this unit in to a dimmer pack

• During long periods of non-use, disconnect the unit’s main power.

• Always mount this unit in safe and stable matter.

• Power-supply cords should be routed so that they are not likely to be walked on or pinched by
items placed upon or against them, paying particular attention to the point they exit from the unit.

• Cleaning -The fixture should be cleaned only as recommended by the manufacturer. See page 25
for cleaning details.

• Heat -The appliance should be situated away from heat sources such as radiators, heat registers,
stoves, or other appliances (including amplifiers) that produce heat.

• The fixture should be serviced by qualified service personnel when:
A. The power-supply cord or the plug has been damaged.
B. Objects have fallen, or liquid has been spilled into the fixture.
C. The fixture has been exposed to rain or water.
D. The fixture does not appear to operate normally or exhibits a marked change in performance.
E. The fixture has fallen and/or subjected to extreme handling.

ADJ Products, LLC - www.adj.com - Focus Beam LED User Manual Page 5

Focus Beam LED Safety Precautions

POTENTIAL INTERNAL FIXTURE DAMAGE FROM EXTERNAL SOURCES OF LIGHT BEAMS

External sources of light beams from direct sunlight, lighting moving head xtures, and lasers, which
are focused directly towards the exterior housing and/or penetrate the front lens opening of ADJ
lighting xtures, can cause severe internal damage including burning to optics, dichroic color lters,
glass and metal gobos, prisms, animation wheels, frost lters, iris, shutters, motors, belts, wiring,
discharge lamps, and LEDs.

This issue is not specic only to ADJ lighting xtures, it is a common issue with lighting xtures
from all manufacturers. Although there is no true way to fully prevent this issue from happening, the
guidelines below can prevent any potential damage from occurring if followed. Contact ADJ Service
for more details.

DO NOT EXPOSE THE FIXTURE AND/OR FRONT LENS OPENING TO LIGHT BEAMS FROM DIRECT
SUNLIGHT, OTHER LIGHTING MOVING HEAD FIXTURES, AND LASERS WHILE UNPACKING,
INSTALLATION, USE, AND EXTENDED IDLE TIMES OUTDOORS.
DO NOT FOCUS A LIGHT BEAM FROM ONE LIGHTING FIXTURE DIRECTLY TOWARDS ANOTHER.

ADJ Products, LLC - www.adj.com - Focus Beam LED User Manual Page 6

Focus Beam LED Overview

FOCUS BEAM LED

FOCUS BEAM LED

UPDATED 9/26/19

1. Service Port

2. LED Display

3. LEFT Button

4. DOWN Button

1 2 3 4 5

8
7

5. ENTER Button

6

6. RIGHT Button

7. UP Button

8. MODE Button

9. powerCON In

10. Fuse (3A)

11. 3-Pin DMX In/Out
5-Pin DMX In/Out
(Updated 9/26/19)

8
7

6

1 2 3 4 5

12. powerCON Out

10 11 12910 11 129

ADJ Products, LLC - www.adj.com - Focus Beam LED User Manual Page 7

Focus Beam LED Installation

NOTICE: When installing the unit, the trussing or area of installation must be able to hold 10 times

the weight without any deformation. The suitable enviromental temperature for this lighting xture is
between -25˚ C to 45˚ C. Do not place this lighting xture in an enviroment where the temperatures

are under or above the temperatures stated above. This will allow the xture to run at its best and
help prolong the xture life. Be sure this xture is kept at least 12m (40ft) away from any ammable
materials (decoration etc.).

SAFETY CABLE
RIGGING POINT

OMEGA BRACKET
ATTACHMENT POINTS

Screw one clamp each via a M12 screw and nut into the Omega bracket. Insert the quick-lock fasteners
of the Omega holder’s into the respective holes on the bottom of the Focus Beam LED. Tighten the
quick-lock fasteners fully clockwise. Always use and install the supplied safety cable as a safety
measure to prevent accidental damage and/or injury in the event the clamp fails. Pull the safety
cable through the openings located on the base plate and over the trussing system or a safe xation
spot. Insert the end in the carabine and tighten the safety screw. Note: Never use the carrying handles
for secondary attachment.

ADJ Products, LLC - www.adj.com - Focus Beam LED User Manual Page 8

Focus Beam LED DMX Set Up

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

DMX512

DMX+,DMX-,COMMON

1

2

3

Termination reduces signal errors and
avoids signal transmission problems
and interference. It is always advisable
to connect a DMX terminal, (Resistance
120 Ohm 1/4 W) between PIN 2 (DMX-)
and PIN 3 (DMX +) of the last fixture.

DMX-512: DMX is short for Digital Multiplex. This is a universal protocol used as a form of commu-
nication between intelligent fixtures and controllers. A DMX controller sends DMX data instructions
from the controller to the fixture. DMX data is sent as serial data that travels from fixture to fixture
via the DATA “IN” and DATA “OUT” XLR terminals located on all DMX fixtures (most controllers only

have a DATA “OUT” terminal).

DMX Linking: DMX is a language allowing all makes and models of dierent manufactures to be
linked together and operate from a single controller, as long as all xtures and the controller are DMX
compliant. To ensure proper DMX data transmission, when using several DMX fixtures try to use
the shortest cable path possible. The order in which fixtures are connected in a DMX line does not
influence the DMX addressing. For example; a fixture assigned a DMX address of 1 may be placed
anywhere in a DMX line, at the beginning, at the end, or anywhere in the middle. When a fixture is
assigned a DMX address of 1, the DMX controller knows to send DATA assigned to address 1 to that
unit, no matter where it is located in the DMX chain.

Data Cable (DMX Cable) Requirements (For DMX Operation): The Focus Beam LED can be controlled
via DMX-512 protocol. The Focus Beam LED has 2 DMX channel modes. The DMX address is set on the
front panel of the Focus Beam LED. Your unit and your DMX controller require a standard 3-pin XLR connec-
tor for data input and data output (Figure 1). We recommend Accu-Cable DMX cables. If you are making
your own cables, be sure to use standard 110-120 Ohm shielded cable (This cable
may be purchased at almost all pro lighting stores). Your cables should be made
with a male and female XLR connector on either end of the cable. Also remember
that DMX cable must be daisy chained and cannot be split.

Figure 1

Notice: Be sure to follow gures two and three when making your own cables. Do not use the ground
lug on the XLR connector. Do not connect the cable’s shield conductor to the ground lug or allow the
shield conductor to come in contact with the XLR’s outer casing. Grounding the shield could cause a
short circuit and erratic behavior.

XLR Male Socket

1 Ground

Figure 3

DMX512 OUT

3-PIN XLR

2 Cold

3 Hot

1

3

2

XLR Female Socket

2 Cold

COMMON

DMX +

DMX -

1 Ground

3 Hot

1

DMX512 IN

3

3-PIN XLR

2

Figure 2

XLR Pin Conguration

Pin 1 = Ground

Pin 2 = Data Compliment (negative)

Pin 3 = Data True (positive)

ADJ Products, LLC - www.adj.com - Focus Beam LED User Manual Page 9

Focus Beam LED DMX Set Up

POWER

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

and PIN 3 (DMX +) of the last fixture.

Special Note: Line Termination.

When longer runs of cable are used, you may need to use a termina­tor on the last unit to avoid erratic behavior. A terminator is a 110-120 ohm 1/4 watt resistor which is
connected between pins 2 and 3 of a male XLR connector (DATA + and DATA -). This unit is inserted
in the female XLR connector of the last unit in your daisy chain to terminate the line. Using a cable
terminator (ADJ part number Z-DMX/T) will decrease the possibilities of erratic behavior.

Termination reduces signal errors and

1

3

avoids signal transmission problems
and interference. It is always advisable

2

to connect a DMX terminal, (Resistance
120 Ohm 1/4 W) between PIN 2 (DMX-)

Figure 4

5-Pin XLR DMX Connectors.

Some manufactures use 5-pin DMX-512 data cables for DATA transmis­sion in place of 3-pin. 5-pin DMX xtures may be implemented in a 3-pin DMX line. When inserting
standard 5-pin data cables in to a 3-pin line a cable adaptor must be used, these adaptors are readily
available at most electric stores. The chart below details a proper cable conversion.

3-Pin XLR to 5-Pin XLR Conversion

Conductor 5-Pin XLR Male (In)3-Pin XLR Female (Out)

Ground/Shield

Data Compliment (- signal)

Data True (+ signal)

Not Used

Not Used

Pin 1

Pin 2

Pin 3

Pin 1

Pin 2

Pin 3

Do Not Use

Do Not Use

ADJ Products, LLC - www.adj.com - Focus Beam LED User Manual Page 10

Focus Beam LED DMX Addressing

All xtures should be given a DMX starting address when using a DMX controller, so the correct xture
responds to the correct control signal. This digital starting address is the channel number from which
the xture starts to “listen” to the digital control signal sent out from the DMX controller. The assignment
of this starting DMX address is achieved by setting the correct DMX address on the digital control
display on the xture.

You can set the same starting address for all xtures or a group of xtures, or set dierent addresses
for each individual xture. Setting all xtures to the same DMX address will cause all xtures to react
in the same way, in other words, changing the settings of one channel will aect all the xtures

simultaneously.

If you set each xture to a dierent DMX address, each unit will start to “listen” to the channel number
you have set, based on the quantity of DMX channels of each xture. That means changing the settings
of one channel will only aect the selected xture.

In the case of the Focus Beam LED, when in 16 channel mode you should set the starting DMX ad­dress of the rst unit to 1, the second unit to 17 (16 + 1), the third unit to 33 (17 + 16), and so on. (See
the chart below for more details.)

Channel Mode

16Channels 1 17 33 49

18 Channels 1 19 37 55

Unit1

Address

Unit2

Address

Unit3

Address

Unit4

Address

ADJ Products, LLC - www.adj.com - Focus Beam LED User Manual Page 11

Focus Beam LED DMX Modes & Values

16 Channels 18 Channels Values

1 1

2

2 3

4

3 5

000-255

000-255

000-255

000-255

000-004
005-011
012-018
019-025
026-032
033-039
040-046
047-053
054-060
061-067
068-074
075-081
082-088
089-095
096-102
103-109
110-116
117-123
124-130
131-137
138-144
145-151
152-158
159-165
166-172
173-179
180-186
187-193
194-220
221-229
230-255

Functions

PAN MOVEMENT 8-BIT:

Pan Movement (0° - 630°)

PAN FINE 16-BIT:

Fine Control of Pan Movement

TILT MOVEMENT 8-BIT:

Tilt Movement (0° - 270°)

TILT FINE 16-BIT:

Fine Control of Tilt Movement

COLOR WHEEL:

Open / White
White + Red
Red
Red + Light Blue
Light Blue
Light Blue + Green
Green
Green + Yellow
Yellow
Yellow + Orange
Orange
Orange + Magenta
Magenta
Magenta + Amber
Amber
Amber + Lime
Lime
Lime + Purple
Purple
Purple + Pink
Pink
Pink + Cyan
Cyan
Cyan + CTO
CTO
CTO + Blue
Blue
Blue + White
Clockwise Rotation Fast - Slow
Stop
Counter-Clockwise Rotation Slow - Fast

NOTE: The Prism and Frost channels CANNOT be used at the same time. The Frost channel will
override the Prism channel.

ADJ Products, LLC - www.adj.com - Focus Beam LED User Manual Page 12

Focus Beam LED DMX Modes & Values

16 Channels 18 Channels Values

000-003
004-007
008-011
012-015
016-019
020-023
024-027
028-031
032-035
036-039
040-043
044-047
048-051
052-055

4 6

5 7

6 8

7 9

8 10

056-059
060-063
064-068
069-072
073-076
077-080
081-084
085-089
090-093
094-097
098-101
102-105
106-110
111-114
115-118
119-122
123-127
128-189
190-193
194-255

000-007
008-255

000-127
128-189
190-193
194-255

000-007
008-255

000-127
128-189
190-193
194-255

Functions

GOBO WHEEL:

Open
Gobo 1
Gobo 2
Gobo 3
Gobo 4
Gobo 5
Gobo 6
Gobo 7
Gobo 8
Gobo 9
Gobo 10
Gobo 11
Gobo 12
Gobo 13
Gobo 14
Open
Gobo 1 Shake
Gobo 2 Shake
Gobo 3 Shake
Gobo 4 Shake
Gobo 5 Shake
Gobo 6 Shake
Gobo 7 Shake
Gobo 8 Shake
Gobo 9 Shake
Gobo 10 Shake
Gobo 11 Shake
Gobo 12 Shake
Gobo 13 Shake
Gobo 14 Shake
Open Shake
Counter-Clockwise Rotation Fast - Slow
Stop
Clockwise Rotation Slow - Fast

PRISM 1 (8 FACET CIRCULAR):

Close
Open

ROTATING PRISM 1 (8 FACET CIRCULAR):

Indexing
Clockwise Rotation Fast - Slow
Stop
Counter-Clockwise Rotation Slow - Fast

PRISM 2 (6 FACET LINEAR):

Close
Open

ROTATING PRISM 2 (6 FACET LINEAR):

Indexing
Clockwise Rotation Fast - Slow
Stop
Counter-Clockwise Rotation Slow - Fast

ADJ Products, LLC - www.adj.com - Focus Beam LED User Manual Page 13

Focus Beam LED DMX Modes & Values

16 Channels 18 Channels Values

000-031
032-063
064-095

9 11

10 12

11 13

12 14

13 15

14 16

15 17

096-127
128-159
160-191
192-223
224-255

000-255

000-020
021-040
041-060
061-080
081-100
101-120

121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140

141-255

000-255

Functions

SHUTTER & STROBING:

Close
Open
Strobing Slow - Fast
Open
Pulsating Strobe
Open
Random Strobing Slow - Fast
Open

MASTER DIMMER:

0% - 100% 000-255

DIMMER FINE:

0% - 100% 000-255

FOCUS:

Linear Near - Far000-255

FROST:

0% - 100%

DIMMER MODES:

Standard
Stage
TV
Architectural
Theatre
Stage 2

DIMMER DELAY TIME

0.1Sec.

0.2Sec.

0.3Sec.

0.4Sec.

0.5Sec.

0.6Sec.

0.7Sec.

0.8Sec.

0.9Sec.

1.0Sec.

1.5Sec.

2.0Sec.

3.0Sec.

4.0Sec.

5.0Sec.

6.0Sec.

7.0Sec.

8.0Sec.

9.0Sec.
10Sec.
Default to Unit Setting

PAN/TILT SPEED:

Fast - Slow

ADJ Products, LLC - www.adj.com - Focus Beam LED User Manual Page 14

Focus Beam LED DMX Modes & Values

16 Channels 18 Channels Values

000-010
011-078

11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30

16 18

31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60

Functions

LED REFRESH RATE & SPECIAL FUNCTIONS:

Default LED Refresh Rate 1200Hz
Refresh Rate (Hz)
900
910
920
930
940
950
960
970
980
990
1000
1010
1020
1030
1040
1050
1060
1070
1080
1090
1100
1110
1120
1130
1140
1150
1160
1170
1180
1190
1210
1220
1230
1240
1250
1260
1270
1280
1290
1300
1310
1320
1330
1340
1350
1360
1370
1380
1390
1400

ADJ Products, LLC - www.adj.com - Focus Beam LED User Manual Page 15

Focus Beam LED DMX Modes & Values

16 Channels 18 Channels Values

61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76

16 18

77
78

79
080-089
090-099
100-109
110-119
120-129
130-139
140-149
150-159
160-169
170-179
180-189
190-199
200-209
210-219
220-229
230-239
240-249
250-255

Functions

LED REFRESH RATE & SPECIAL FUNCTIONS:

1410
1420
1430
1440
1450
1460
1470
1480
1490
1500
2500
4000
5000
6000
10,000
15,000
20,000
25,000
Disable LED Refresh Rate
Enable Blackout with Pan/Tilt Movement
Disable Blackout with Pan/Tilt Movement
Enable Blackout with Color Change
Disable Blackout with Color Change
Enable Blackout with Gobo Change
Disable Blackout with Gobo Change
Pan/Tilt Reset
Focus Reset
Effect Reset
Shutter Reset
Internal Program 1 (Scenes 1-8)
Internal Program 2 (Scenes 9-16)
Internal Program 3 (Scenes 17-24)
Internal Program 4 (Scenes 25-32)
Internal Program 5 (Scenes 33-40)
Internal Program 6 (Scenes 41-48)
Internal Program 7 (Scenes 49-56)
No Function

SOFTWARE UPDATE - DMX Values 250-255 Updated in Software Version >1.0.4

Reset All250-25516 18

ADJ Products, LLC - www.adj.com - Focus Beam LED User Manual Page 16

Focus Beam LED System Menu

SYSTEM MENU

The xture includes an easy to navigate system menu control panel display where all necessary
settings and adjustments are made. (See image below) During normal operation, pressing the MODE
button once will access the xture’s main menu. Once in the main menu, you can navigate through
the dierent menus and the sub-menus with the UP and DOWN buttons. When you reach a eld that
requires adjusting, press the ENTER button to access that eld and use the UP, DOWN, LEFT or
RIGHT buttons (depending on the sub menu) to adjust the eld. Pressing the ENTER button once
more to conrm your setting. You may exit the main menu at any time without making any adjustments

by pressing the MODE button.

To access the system menu when the xture is not powered using the internal battery, press

and hold the MODE button to illuminate the LCD screen until the DMX address is displayed.
Then navigate to the desired system menu.

FOCUS BEAM LED

LCD CONTROL PANEL LOCKOUT

When the Key Lock function is activated, the control panel will automatically lock after the time set
under the SCREEN SAVER DELAY submenu.

When the Key Lock function is set to ON, the control panel will lock and the display will show “Un­lock” at the bottom of the display. Press and hold the MODE button for 3 seconds to unlock.

When the Key Lock function is set to ON1, the control panel will lock and the display will show “Unlock”
at the bottom of the display. To unlock the display follow these steps:

1. Press the UP button, and the display will show *.

2. Press the DOWN button, and the display will show **.

3. Press the UP button, and the display will show ***.

4. Press the DOWN button, and the display will show ****.

5. Press the ENTER buttton, to conrm.

If the button sequence was entered correctly, the display and control panel will unlock. If the button
sequence was entered incorrectly, the display will return to the DMX addess display.

ADJ Products, LLC - www.adj.com - Focus Beam LED User Manual Page 17

Focus Beam LED System Menu

Software Version <V1.0.3

MENU OPTIONS DESCRIPTIONSUBMENU

DMX Addressing

DMX Channel Mode Selection

DMX Lost Status

Reverse Pan Motion

Reverse Tilt Motion

Pan/Tilt Movement Feedback

Pan/Tilt Movement Speed

Sleep Setting (No Activity)

Fan Speed Setting

DMX SETTINGS

Set Address

DMX Channel Mode

No DMX Status Hold Last / Blackout / Manual

001-XXX

16Ch / 18Ch

Pan Invert: ON / OFF

Tilt Invert: ON / OFF

Status Settings

P./T. Feedback: ON / OFF

P./T. Speed: Speed 1 / Speed 2

Hibernation: Off / 01M~99M / 15M

Fan Settings

Head Fan: Auto / High / Silent (Low)

PERSONALITY

MANUAL CONTROL

Dim Modes

LED Refresh Rate

Gamma

Reset Motors

Display

Service

Pan
Pan Fine
Tilt
Tilt Fine
Color
Gobo
Prism 1
Prism 1 Rot.
Prism 2
Prism 2 Rot.
Shutter
Dimmer
Dimmer Fine
Focus
Frost
Dim Modes
P/T Speed
Special Function

Standard/Stage/TV/Architectur/Theatre/Stage2
Dim Speed: 0.1-0.9s ~ 1-10s

1200 / 900-1500 / 2500 / 4000 / 5000 / 6000
10000 / 15000 / 20000 / 25000 (Hz)

1.0 / 2.0 / 2.2 / 2.4 / 2.6 / 2.8 Gamma Brightness

Reset All Motors: YES / NO

Pan/Tilt Reset: YES / NO

Effect Reset: YES / NO

Dimming Curve Modes
Dimming Speed

LED Refresh Setting

Reset All Motors

Reset the Pan & Tilt Motors

Reset the Effect Motor

Shutter Reset: YES / NO Reset the Shutter Motor

Intensity: 1~10 (Dimmest-Brightest)

Display Invert: YES / NO

Screen Saver Delay: OFF~10M

Display Intensity Adjustment

Display Inversion

Display Shutoff Time

Key Lock: OFF / ON / ON1 Display Control Lock

Pass Code = 050

Effect Adjust (Calibration)

(Pass Code = 50)

USB Port Power: ON / OFF

Update Software: YES / NO

Factory Restore: YES / NO

(Pass Code = 11)

Calibration Adjustment

USB Port Activation

Software Update

Restore Factory Settings

000-255
000-255
000-255
000-255
000-255
000-255
000-255
000-255
000-255

Manual Control Settings
000-255
000-255
000-255
000-255
000-255
000-255
000-255
000-255
000-255

ADJ Products, LLC - www.adj.com - Focus Beam LED User Manual Page 18

Focus Beam LED System Menu

Software Version >V1.0.4

MENU OPTIONS DESCRIPTIONSUBMENU

DMX SETTINGS

PERSONALITY

Set Address

DMX Channel Mode

No DMX Status Hold Last / Blackout / Manual

001-XXX

16Ch / 18Ch

Pan Degree: 630 / 540

Pan Invert: ON / OFF

Status Settings

Tilt Invert: ON / OFF

P./T. Feedback: ON / OFF

P./T. Speed: Speed 1 / Speed 2

Hibernation: Off / 01M~99M / 15M

Fan Settings

Dim Modes

LED Refresh Rate

Dim Curve

Head Fan: Auto / High / Silent (Low)

Standard/Stage/TV/Architectur/Theatre/Stage2
Dim Speed: 0.1-0.9s ~ 1-10s

1200 / 900-1500 / 2500 / 4000 / 5000 / 6000
10000 / 15000 / 20000 / 25000 (Hz)

Linear / Square / Inverse Square / S-Curve Set Dimming Curve

Reset All Motors: YES / NO

Pan/Tilt Reset: YES / NO

Reset Motors

Effect Reset: YES / NO

DMX Addressing

DMX Channel Mode Selection

DMX Lost Status

Pan Degree Selection

Reverse Pan Motion

Reverse Tilt Motion

Pan/Tilt Movement Feedback

Pan/Tilt Movement Speed

Sleep Setting (No Activity)

Fan Speed Setting

Dimming Curve Modes
Dimming Speed

LED Refresh Setting

Reset All Motors

Reset the Pan & Tilt Motors

Reset the Effect Motor

MANUAL CONTROL

Display

Service

Pan
Pan Fine
Tilt
Tilt Fine
Color
Gobo
Prism 1
Prism 1 Rot.
Prism 2
Prism 2 Rot.
Shutter
Dimmer
Dimmer Fine
Focus
Frost
Dim Modes
P/T Speed
Special Function

Shutter Reset: YES / NO Reset the Shutter Motor

Intensity: 1~10 (Dimmest-Brightest)

Display Invert: YES / NO

Screen Saver Delay: OFF~10M

Display Intensity Adjustment

Display Inversion

Display Shutoff Time

Key Lock: OFF / ON / ON1 Display Control Lock

Pass Code = 050

Effect Adjust (Calibration)

(Pass Code = 50)

USB Port Power: ON / OFF

Update Software: YES / NO

Factory Restore: YES / NO

(Pass Code = 11)

Calibration Adjustment

USB Port Activation

Software Update

Restore Factory Settings

000-255
000-255
000-255
000-255
000-255
000-255
000-255
000-255
000-255

Manual Control Settings

000-255
000-255
000-255
000-255
000-255
000-255
000-255
000-255
000-255

ADJ Products, LLC - www.adj.com - Focus Beam LED User Manual Page 19

Focus Beam LED System Menu

MENU OPTIONS DESCRIPTIONSUBMENU

INTERNAL
PROGRAMS

INFORMATION

Program 1
Program 2
Program 3
Program 4
Program 5
Program 6
Program 7

Fixture Life Time

Total LED Time

Speed: 000~255 Fade: 000~255
Speed: 000~255 Fade: 000~255
Speed: 000~255 Fade: 000~255
Speed: 000~255 Fade: 000~255
Speed: 000~255 Fade: 000~255
Speed: 000~255 Fade: 000~255
Speed: 000~255 Fade: 000~255

Power On Time: XXXXXX Hours

P-On Time-R: XXXXXX Hours

P-On Time-Reset: YES / NO

Pass Code = 50

LED On Time: XXXXXX Hours

LED On Time-R: XXXXXX Hours

LED Hours Reset: YES / NO

Pass Code = 50

Current: XXX ˚F / XXX ˚C

Max Resettable: XXX ˚F / XXX ˚C

LED’s

Fixture Temps

Max Not Resettable: XXX ˚F / XXX ˚C

Reset Lamp Temp: YES / NO

(Pass Code = 050)

Fan Info. (RPM) LED Fan: XXXX LED Fan Speed

DMX Values

(See Note 3)

Error Logs

Software Version X.XX Current Software Version

Notes:
(1) Current Maximum Temperature - Maximum fixture temp. that has been recorded, before reset and after reset.
(2) Maximum Temperature - Overall maximum fixture temp. that has been recorded. (Not Resettable)
(3) DMX Value options depend on the current DMX Channel mode setting.

(3)

Pan / Pan Fine / Tilt / Tilt Fine / Color / Gobo /
Prism 1 / Prism 1 Rot / Prism 2 / Prism 2 Rot /
Dimmer / Dimmer Fine / Focus / Frost /
Dim Modes / P/T Speed / Special Function

Fixture Errors

Reset Error Log - Pass Code = 50

Program 1 with Adjustments
Program 2 with Adjustments
Program 3 with Adjustments
Program 4 with Adjustments
Program 5 with Adjustments
Program 6 with Adjustments
Program 7 with Adjustments

Total Running Time
(Not Resettable)

Total Running Time
(Resettable)

Reset Total Running Time

Total LED On Running
Time (Not Resettable)

LED On Running Time
(Resettable)

Reset LED Running Time

Current Head Temperature

Maximum Temperature

(1)

Reached (Resettable)

(See Note 1)

Maximum Temperature

(2)

Reached (Not Resettable)

(See Note 2)

Reset LED Temperature
(Max Resettable)

Current DMX Values

List of Errors (One by One)

Clear the Error Log

ADJ Products, LLC - www.adj.com - Focus Beam LED User Manual Page 20

Focus Beam LED System Menu

DMX SETTINGS - The submenus listed under DMX SETTINGS are as follows: Set Address, DMX
Channel Mode, and No DMX Status.

- SET ADDRESS - In this submenu you can nd and set your desired DMX address.

- DMX CHANNEL MODE - In this submenu you can nd and set your desired DMX channel mode.

- NO DMX STATUS - This submenu setting is used as a precaution mode in case the DMX signal is

lost or interrupted. The operating mode chosen in this submenu is the running mode the xture
will go into when the DMX signal is lost. Listed below are the 3 modes.

• Hold Last - This setting will have the xture stay in the last DMX setup.

• Blackout - This setting will have the xture automatically go into stand by mode.

• Manual - This setting will go into the current manual control set up. See MANUAL CONTROL.

PERSONALITY - The submenus listed under PERSONALITY are as follows: Status Settings, Fan
Settings, Dim Modes, LED Refresh Rate, Gamma, Reset Motors, Display, and Service.

- STATUS SETTINGS - In this submenu you are able to access and adjust/change: Pan Degree,

Pan Invert, Tilt Invert, P./T. Feedback, P./T. Speed, and Hibernation.
NOTE: Pan Degree Added with software version >1.0.4

- FAN SETTINGS - In this submenu you are able to select your desired fan speed setting.

- DIM MODES - In this submenu you are able to select your desired dimmer mode and adjust the

dimming speed time.

- LED REFRESH RATE - In this submenu you are able to select your desired LED refresh rate.

- GAMMA - In this submenu you are able to select your desired gamma setting.

NOTE: Remove from software version <1.0.3.

- DIM CURVE - In this submenu you are able to select your desired dimmer curve setting.

NOTE: Added with software version >1.0.4

- RESET MOTORS - In this submenu you are able to reset selected motors.

- DISPLAY - In this submenu you you are able to adjust the display intensity, invert the display, activate

the display blackout, and activate/deactivate the display lock.

- SERVICE - In this submenu you are able to access and adjust/change: the calibration (eect
adjust), activate the service port, update software, and restore the factory settings.

MANUAL CONTROL - This menu is for manual testing and manual control. Pan, tilt, color wheel,
gobo wheel, prism 1, prism 1 rotation, shutter, dimmer, focus, frost can all be tested/adjusted.
NOTE: The Prism and Frost features CANNOT be used at the same time.

ADJ Products, LLC - www.adj.com - Focus Beam LED User Manual Page 21

Focus Beam LED System Menu

INTERNAL PROGRAMS - In this menu you are able to select 1 of 7 internal programs to run. Program
running speed and fade speed are adjustable.

INFORMATION - The submenus listed under INFORMATION are as follows: Fixture Life Time,
Total LED Time, Fixture Temps, Fan Info. (RPM), DMX Values, Error Logs, and Software Version.

- FIXTURE LIFE TIME

• Power On Time -The TOTAL power ON running time of the unit is displayed. This time CANNOT
be reset.

• P-On Time-R - The CURRENT power ON running time of the unit is displayed. This running time
may not be the same as the total power ON running time displayed under “Power On Time”. This

time CAN be reset. NOTE: The displayed time represents the current power ON time since the
last reset.

• P-On Time-Reset - Reset the CURRENT power ON running time that is displayed under “P-On Time-R”.

- TOTAL LED TIME

• LED On Time - The TOTAL LED ON time is displayed. This total LED ON time CANNOT be reset.
NOTE: The displayed time represents the TOTAL LED ON time.

• LED On Time-R - The CURRENT LED ON running time is displayed. This running time may not
be the same as the total LED ON time displayed under “LED On Time”. This total LED ON time

CAN be reset. NOTE: The displayed time represents the current LED ON time since the last
reset.

• LED On Time Reset - With this function you can reset the CURRENT LED ON time that is displayed
under “LED On Time-R”.

- FIXTURE TEMPS

• LED - The current temperature of the LED is displayed.

• Reset LED Temp - Reset the LED temperature reading.

- FAN INFO. (RPM) - In this submenu the current fan speed will be displayed.

- DMX VALUES - Displays the DMX values of any DMX channel that is currently in use. NOTE: DMX
value options depend on the current DMX channel mode setting.

- ERROR LOGS - In this submenu you are able to check any unit errors as well a clearing the error

log.

- SOFTWARE VERSION - Current software version is displayed.

ADJ Products, LLC - www.adj.com - Focus Beam LED User Manual Page 22

Focus Beam LED Master-Slave Set Up

Master-Slave Configuration:

This function will allows you to link units together to run in a Master-Slave set-up. In a Master-Slave
set up one unit will act as the controlling unit and the others will react to the controlling units built-in
programs. Any unit can act as a Master or as a Slave however, only one unit can be programmed to
act as the “Master.”

Master-Slave Connections and Settings:

1. Daisy chain your units via the XLR connector on the rear of the unit. Use standard XLR data
cables to link your units together. Remember that the Male XLR connector is the input and the
Female XLR connector is the ouput. The first unit in the chain (master) will use the female XLR
connector only. The last unit in the chain will use the male XLR connector only.

2. Set the “Master” unit to your desired mode of operation.

3. Connect the rst “Slave” unit to the “Master.”

4. Set the “Slave” unit(s) to DMX control.

ADJ Products, LLC - www.adj.com - Focus Beam LED User Manual Page 23

Focus Beam LED Dimmer Mode Chart

DIMMER

100%

50%

10%

0%

Time (ms)

255 255

0 0

Stage 780 1100 1540 1660

TV 1180 1520 1860 1940

Architectural 1380 1730 2040 2120

0 sec Fade Time

1 sec Fade Time

Rise Time Down Time

0 Sec

Dimming Curve

Ramp Effect

Rise Time (ms) Down Time (ms) Rise Time (ms) Down Time (ms)

Standard (default) 0 0 0 0

Theatre 1580 1940 2230 2280

Stage 2

0 1100 0 1660

Focus Beam LED Dimmer Curve Chart

100%

Output

100%

Output

100%

Output

100%

Output

0

DMX % DMX % DMX % DMX %

0

0

LINEAR SQUARE INVERSE SQUARE S-CURVE

ADJ Products, LLC - www.adj.com - Focus Beam LED User Manual Page 24

0

Focus Beam LED Static Gobos

OPEN GOBO 1 GOBO 2 GOBO 3 GOBO 4

GOBO 7 GOBO 8 GOBO 9 GOBO 10 GOBO 11 GOBO 12

Focus Beam LED Dimensional Drawing

8.34” / 212mm

11.102” / 282mm

GOBO 5 GOBO 6

GOBO 13

7.55” / 191.81mm

GOBO 14

14” / 355.95mm

17.61” / 447.3mm

6.850” / 174mm

4.213” / 107mm

3.676” / 93.36mm

10.96” / 278.61mm

3.543” / 90mm

10.96” / 278.61mm

6.85” / 174mm

ADJ Products, LLC - www.adj.com - Focus Beam LED User Manual Page 25

Focus Beam LED Fuse Replacement

Unplug the unit from any power source it may be connected to. Once the power has been disconnected,
use a flat head screw driver to unscrew the fuse holder located next to the powerCON input. Remove
the bad fuse and replace with a new one, and screw the fuse holder back in.

Focus Beam LED Multiple Unit Power Linking

With this feature you can connect the xtures to one another using the power cable input and

output sockets.
NOTE: USE CAUTION WHEN POWER LINKING OTHER FIXTURES AS THE POWER
CONSUMPTION OF OTHER MODEL FIXTURES MAY EXCEED THE MAX POWER OUTPUT ON
THIS FIXTURE! CHECK SILK SCREEN FOR MAX AMPS.

Focus Beam LED Trouble Shooting

Listed below are a few common problems the user may encounter, with solutions.

Unit not responding to DMX:

1. Check that the DMX cables are connected properly and are wired correctly (pin 3 is “hot”; on
some other DMX devices pin 2 may be ‘hot’). Also, check that all cables are connected to the right
connectors; it does matter which way the inputs and outputs are connected.

Focus Beam LED Cleaning

Due to fog residue, smoke, and dust cleaning the internal and external optical lenses must be car­ried out periodically to optimize light output.

1. Use normal glass cleaner and a soft cloth to wipe down the outside casing.

2. Clean the external optics with glass cleaner and a soft cloth every 20 days.

3. Always be sure to dry all parts completely before plugging the unit back in.
Cleaning frequency depends on the environment in which the fixture operates (i.e. smoke, fog resi­due, dust, dew).

ADJ Products, LLC - www.adj.com - Focus Beam LED User Manual Page 26

Focus Beam LED Limited Warranty (USA Only)

MANUFACTURER’S LIMITED WARRANTY

A. ADJ Products, LLC hereby warrants, to the original purchaser, ADJ Products, LLC products to be free of manufacturing

defects in material and workmanship for a prescribed period from the date of purchase (see specific warranty period
on reverse). This warranty shall be valid only if the product is purchased within the United States of America, including
possessions and territories. It is the owner’s responsibility to establish the date and place of purchase by acceptable
evidence, at the time service is sought.

B. For warranty service you must obtain a Return Authorization number (RA#) before sending back the product–please

contact ADJ Products, LLC Service Department at 800-322-6337. Send the product only to the ADJ Products, LLC
factory. All shipping charges must be pre-paid. If the requested repairs or service (including parts replacement) are
within the terms of this warranty, ADJ Products, LLC will pay return shipping charges only to a designated point
within the United States. If the entire instrument is sent, it must be shipped in it’s original package. No accessories
should be shipped with the product. If any accessories are shipped with the product, ADJ Products, LLC shall
have no liability whatsoever for loss of or damage to any such accessories, nor for the safe return thereof.

C. This warranty is void if the serial number has been altered or removed; if the product is modified in any manner

which ADJ Products, LLC concludes, after inspection, affects the reliability of the product; if the product has been
repaired or serviced by anyone other than the ADJ Products, LLC factory unless prior written authorization was issued
to purchaser by ADJ Products, LLC; if the product is damaged because not properly maintained as set forth in the

instruction manual.

D. This is not a service contract, and this warranty does not include maintnance, cleaning or periodic check up.

During the period specified above, ADJ Products, LLC will replace defective parts at its expense with new or
refurbished parts, and will absorb all expenses for warranty service and repair labor by reason of defects in material or
workmanship. The sole responsibility of ADJ Products, LLC under this warranty shall be limited to the repair of the
product, or

replacement thereof, including parts, at the sole discretion of ADJ Products, LLC. All products covered by this

warranty were manufactured after August 15, 2012, and bear indentifying marks to that effect.

E. ADJ Products, LLC reserves the right to make changes in design and/or improvements upon its products without

any obligation to include these changes in any products theretofore manufactured.

No warranty, whether expressed or implied, is given or made with respect to any accessory supplied with products

described above. Except to the extent prohibited by applicable law, all implied warranties made by ADJ Products,
LLC in connection with this product, including warranties of merchantability or fitness, are limited in duration to the
warranty period set forth above. And no warranties, whether expressed or implied, including warranties of merchantability or
fitness, shall apply to this product after said period has expired. The consumer’s and/or Dealer’s sole remedy shall
be such repair or replacement as is expressly provided above; and under no circumstances shall ADJ Products,
LLC be liable for any loss or damage, direct or consequential, arising out of the use of, or inability to use, this
product.

This warranty is the only written warranty applicable to ADJ Products, LLC Products and supersedes all prior warranties

and written descriptions of warranty terms and conditions heretofore published.

MANUFACTURER’S LIMITED WARRANTY PERIODS:

• Non L.E.D. Lighting Products = 1-year (365 days) Limited Warranty (Such as: Special Effect Lighting, Intelligent
Lighting, UV lighting, Strobes, Fog Machines, Bubble Machines, Mirror Balls, Par Cans, Trussing, Lighting Stands
etc. excluding LED and lamps)

• Laser Products = 1 Year (365 Days) Limited Warranty (excluding laser diodes which have a 6 month limited

warranty)

• L.E.D. Products = 2-year (730 days) Limited Warranty (excluding batteries which have a 180 day limited warranty).

Note: 2 Year Warranty only applies to purchases within the United States.

• StarTec Series = 1 Year Limited Warranty (excluding batteries which have a 180 day limited warranty).

• ADJ DMX Controllers = 2 Year (730 Days) Limited Warranty

ADJ Products, LLC - www.adj.com - Focus Beam LED User Manual Page 27

Focus Beam LED Specifications

Model:

Voltage: 100V ~ 240V/50~60Hz
LEDs: 1 x 80W Cool White LED
Color Temperature: 7400K
Working Position: Any safe working position
Power Draw: 136W
Fuse: 2A
Dimensions: 10.96” (L) x 7.55” (W) x 17.61” (H)

278.61 x 191.8 x 447.3mm
Weight: 27lbs. / 12.25 kgs
Colors: 13 Colors + White
Gobos: 14 Static Gobos + Open
Prisms: 8 Facet Circular & 6 Facet Linear
DMX Channels: 2 DMX Modes: 16 / 18
Warranty: 2 Year (730 days)

Please Note: Specications and improvements in the design of
this unit and this manual are subject to change without notice.

Focus Beam LED

ADJ Products, LLC - www.adj.com - Focus Beam LED User Manual Page 28