Page 1
FLAT PAR TW12
©2014 ADJ Products, LLC all rights reserved. Information,
specications, diagrams, images, and instructions herein are
subject to change without notice. ADJ Products, LLC logo and
identifying product names and numbers herein are trademarks
of ADJ Products, LLC. Copyright protection claimed includes all
forms and matters of copyrightable materials and information
now allowed by statutory or judicial law or hereinafter granted.
Product names used in this document may be trademarks or
registered trademarks of their respective companies and are
hereby acknowledged. All non-ADJ Products, LLC brands and
product names are trademarks or registered trademarks of their
respective companies.
ADJ Products, LLC and all aliated companies hereby disclaim any and all liabilities for property, equipment, building, and
electrical damages, injuries to any persons, and direct or indirect economic loss associated with the use or reliance of any
information contained within this document, and/or as a result
of the improper, unsafe, unsucient and negligent assembly,
installation, rigging, and operation of this product.
Rev. 10/14
User Instructions
Europe Energy Saving Notice
Energy Saving Matters (EuP 2009/125/EC)
Saving electric energy is a key to help protecting the enviroment.
Please turn o all electrical products when they are not in use. To
avoid power consumption in idle mode, disconnect all electrical
equipment from power when not in use. Thank you!
Page 2
Flat Par TW12 Introduction
Flat Par TW12 Features
Unpacking: Thank you for purchasing the Flat Par TW12 by ADJ Products, LLC. Every Flat Par TW12 has been thoroughly tested and has
been shipped in perfect operating condition. Carefully check the shipping carton for damage that may have occurred during shipping. If the
carton appears to be damaged, carefully inspect your xture for any
damage and be sure all accessories necessary to operate the unit has
arrived intact. In the case damage has been found or parts are missing, please contact our toll free customer support number for further
instructions. Do not return this unit to your dealer without rst contacting customer support.
Introduction: The ADJ Flat Par TW12 is part of a continuing pursuit to
create high quality intelligent lighting. The Flat Par TW12 is a DMX intelligent, high powered LED par fixture. This xture can be used in a stand
alone mode or connected in a Master/Slave conguration. This wash
has five operating modes: Sound Active mode, Auto Run mode, WW/
CW/A Dimmer mode, Static Color mode, and DMX control mode. To
optimize the performance of this product, please read these operating
instructions carefully to familiarize yourself with the basic operations
of this unit. These instructions contain important safety information
regarding the use and maintenance of this unit. Please keep this manual
with the unit, for future reference.
Customer Support: ADJ Products, LLC provides a customer support
line, to provide set up help and to answer any question should you
encounter problems during your set up or initial operation. You may
also visit us on the web at www.adj.com for any comments or suggestions. Service Hours are Monday through Friday 8:00 a.m. to 4:30 p.m.
Pacic Standard Time.
Voice: (323) 582-3322
Fax: (323) 582-3108
E-mail: support@americandj.com
Warning! To prevent or reduce the risk of electrical shock or re, do
not expose this unit to rain or moisture.
Caution! There are no user serviceable parts inside this unit. Do not
attempt any repairs yourself, doing so will void your manufactures warranty. In the unlikely event your unit may require service please contact
ADJ Products, LLC.
PLEASE recycle the shipping carton when ever possible.
ADJ Products, LLC - www.adj.com - Flat Par TW12 User Manual Page 2
• Multi-Colors
• Five Operating Modes
• Electronic Dimming 0-100%
• Built in Microphone
• DMX-512 protocol
• 3-Pin DMX Connection
• 6 DMX Modes: 2 Channel Mode, 3 Channel Mode, 4 Channel
Mode, 5 Channel Mode, 8 Channel Mode, and 9 Channel Mode.
• ADJ LED RC compatiable (Not Included)
• Power Cord Daisy Chain (See page 21)
Flat Par TW12 Warranty Registration
The Flat Par TW12 carries a 2 year limited warranty. Please fill out the
enclosed warranty card to validate your purchase. All returned service
items whether under warranty or not, must be freight pre-paid and
accompany a return authorization (R.A.) number. The R.A. number
must be clearly written on the outside of the return package. A brief
description of the problem as well as the R.A. number must also be
written down on a piece of paper included in the shipping carton. If
the unit is under warranty, you must provide a copy of your proof of
purchase invoice. You may obtain a R.A. number by contacting our
customer support team on our customer support number. All packages returned to the service department not displaying a R.A. number
on the outside of the package will be returned to the shipper.
Flat Par TW12 Installation
The unit should be mounted using a mounting clamp (not provided),
axing it to the mounting bracket that is provided with the unit.
Always ensure that the unit is rmly xed to avoid vibration and slipping while operating. Always ensure that the structure to which you
are attaching the unit is secure and is able to support a weight of 10
times the unit’s weight. Also, always use a safety cable that can hold
12 times the weight of the unit when installing the xture.
The equipment must be installed by a professional, and it must be
installed in a place where it is out of the reach of people’s grasp.
ADJ Products, LLC - www.adj.com - Flat Par TW12 User Manual Page 3
Page 3
Flat Par TW12 Safety Precautions
Flat Par TW12 Set Up
• To reduce the risk of electrical shock or re, do not expose this unit
rain or moisture
• Do not spill water or other liquids into or on to your unit.
• Do not attempt to operate this unit if the power cord has been
frayed or broken. Do not attempt to remove or break o the ground
prong from the electrical cord. This prong is used to reduce the risk
of electrical shock and re in case of an internal short.
• Disconnect from main power before making any type of connection.
• Do not remove the cover under any conditions. There are no user
serviceable parts inside.
• Never operate this unit when it’s cover is removed.
• Never plug this unit in to a dimmer pack
• Always be sure to mount this unit in an area that will allow proper
ventilation. Allow about 6” (15cm) between this device and a wall.
• Do not attempt to operate this unit, if it becomes damaged.
• This unit is intended for indoor use only, use of this product out`
doors voids all warranties.
• During long periods of non-use, disconnect the unit’s main power.
• Always mount this unit in safe and stable matter.
• Power-supply cords should be routed so that they are not likely to
be walked on or pinched by items placed upon or against them,
paying particular attention to the point they exit from the unit.
• Cleaning -The fixture should be cleaned only as recommended by
t he manufacturer. See page 21 for cleaning details.
• Heat -The appliance should be situated away from heat sources
such as radiators, heat registers, stoves, or other appliances (inclu d ing amplifiers) that produce heat.
• The fixture should be serviced by qualified service personnel when:
A. The power-supply cord or the plug has been damaged.
B. Objects have fallen, or liquid has been spilled into the appliance.
C. The appliance has been exposed to rain or water.
D. The appliance does not appear to operate normally or exhibits a
marked change in performance.
Power Supply: The ADJ Flat Par TW12 contains a automatic voltage
switch, which will auto sense the voltage when it is plugged into the
power source. With this switch there is no need to worry about the correct power voltage, this unit can be plugged in anywhere.
DMX-512: DMX is short for Digital Multiplex. This is a universal pro-
tocol used as a form of communication between intelligent fixtures
and controllers. A DMX controller sends DMX data instructions from
the controller to the fixture. DMX data is sent as serial data that travels from fixture to fixture via the DATA “IN” and DATA “OUT” XLR terminals located on all DMX fixtures (most controllers only have a DATA
“OUT” terminal).
DMX Linking: DMX is a language allowing all makes and models of
dierent manufactures to be linked together and operate from a single
controller, as long as all xtures and the controller are DMX compliant. To ensure proper DMX data transmission, when using several
DMX fixtures try to use the shortest cable path possible. The order
in which fixtures are connected in a DMX line does not influence the
DMX addressing. For example; a fixture assigned a DMX address of 1
may be placed anywhere in a DMX line, at the beginning, at the end,
or anywhere in the middle. When a fixture is assigned a DMX address
of 1, the DMX controller knows to send DATA assigned to address 1
to that unit, no matter where it is located in the DMX chain.
Data Cable (DMX Cable) Requirements (For DMX Operation):
The Flat Par TW12 can be controlled via DMX-512 protocol. The Flat Par
TW12 has 6 DMX channel modes, please see pages 7-8 for the dierent
modes. The DMX address is set on the back panel of the Flat Par TW12.
Your unit and your DMX controller require a standard 3-pin XLR connector for data input and data output (Figure 1). We
recommend Accu-Cable DMX cables. If you are
making your own cables, be sure to use standard
110-120 Ohm shielded cable (This cable may be
purchased at almost all pro lighting stores). Your
cables should be made with a male and female
XLR connector on either end of the cable. Also
remember that DMX cable must be daisy chained
and cannot be split.
Figure 1
ADJ Products, LLC - www.adj.com - Flat Par TW12 User Manual Page 4
ADJ Products, LLC - www.adj.com - Flat Par TW12 User Manual Page 5
Page 4
Flat Par TW12 Set Up
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
DMX512
DMX+,DMX-,COMMON
1
2
3
Termination reduces signal errors and
avoids signal transmission problems
and interference. It is always advisable
to connect a DMX terminal, (Resistance
120 Ohm 1/4 W) between PIN 2 (DMX-)
and PIN 3 (DMX +) of the last fixture.
POWER
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
Flat Par TW12 Operating Instructions
Notice: Be sure to follow gures two and three when making your own
cables. Do not use the ground lug on the XLR connector. Do not connect the cable’s shield conductor to the ground lug or allow the shield
conductor to come in contact with the XLR’s outer casing. Grounding
the shield could cause a short circuit and erratic behavior.
COMMON
1
DMX512 IN
3
3-PIN XLR
2
Figure 2
XLR Pin Conguration
1 Ground
3 Hot
Pin 1 = Ground
Pin 2 = Data Compliment (negative)
Pin 3 = Data True (positive)
When longer runs of cable are
Figure 4
Pin 1
Pin 2
Pin 3
Do Not Use
Do Not Use
XLR Male Socket
1 Ground
DMX512 OUT
3-PIN XLR
2 Cold
3 Hot
1
3
2
DMX +
DMX -
XLR Female Socket
2 Cold
Figure 3
Special Note: Line Termination.
used, you may need to use a terminator on the last unit to avoid erratic
behavior. A terminator is a 110-120 ohm 1/4 watt resistor which is connected between pins 2 and 3 of a male XLR connector (DATA + and
DATA -). This unit is inserted in the female XLR connector of the last
unit in your daisy chain to terminate the line. Using a cable terminator
(ADJ part number Z-DMX/T) will decrease the possibilities of erratic
behavior.
5-Pin XLR DMX Connectors.
512 data cables for DATA transmission in place of 3-pin. 5-pin DMX
xtures may be implemented in a 3-pin DMX line. When inserting standard 5-pin data cables in to a 3-pin line a cable adaptor must be used,
these adaptors are readily available at most electric stores. The chart
below details a proper cable conversion.
Conductor 5-Pin XLR Male (In)3-Pin XLR Female (Out)
Ground/Shield
Data Compliment (- signal)
Data True (+ signal)
Not Used
Not Used
ADJ Products, LLC - www.adj.com - Flat Par TW12 User Manual Page 6
Termination reduces signal errors and
1
avoids signal transmission problems
3
and interference. It is always advisable
2
to connect a DMX terminal, (Resistance
120 Ohm 1/4 W) between PIN 2 (DMX-)
and PIN 3 (DMX +) of the last fixture.
Some manufactures use 5-pin DMX-
3-Pin XLR to 5-Pin XLR Conversion
Pin 1
Pin 2
Pin 3
The display will lock after 30 seconds, press the MENU
button for 3 seconds to unlock.
LED Display On/Off:
To set the LED display to turn off after 10 seconds, press the MODE button until “don” is displayed, press the UP button to display “doff”. Now
the display will disappear after 10s. Press any button to turn the display
on again. Be advised though that the display will turn off automatically
after 10 seconds.
To set the display press the MODE button until “dXX” is displayed. “XX”
represents either “on” or “oFF” Use the UP or DOWN buttons to select
either:
“don” = LED display on at all times.
“doFF” = LED display shuts off after 10 seconds.
LED Display Inversion:
Follow these instructions to flip the display 180° so that the display can
be read upside down.
1. Plug the fixture in and press the MODE button until “dXX” is dis-
played. “XX” represents either “on” or “oFF”.
2. Press the SET UP button until “Stnd” is displayed.
3. Press the UP or DOWN buttons to reverse the display 180°.
Operating Modes:
The Flat Par TW12 has five operating modes:
• Sound-Active mode - The unit will react to sound, chasing through the
built in programs.
• Static Color Mode - There are 32 colors to choose from.
• Auto Run Mode - There are 3 Auto Modes to choose from.
• WW/CW/A Dimmer Mode - Choose one of the three colors to remain
static or adjust the intensity of each color to make your desired
color.
• DMX control mode - This function will allow you to control each
individual fixtures traits with a standard DMX 512 controller.
DMX Mode:
Operating through a DMX controller gives the user the freedom to create
their own programs tailored to their own individual needs. The Flat Par
TW12 has 6 DMX modes: 2 Channel mode, 3 Channel mode, 4 Channel
mode, 5 Channel mode, 8 Channel mode, and a 9 Channel mode.
ADJ Products, LLC - www.adj.com - Flat Par TW12 User Manual Page 7
Page 5
Flat Par TW12 Operating Instructions
Flat Par TW12 Operating Instructions
1. This function will allow you to control each individual fixture’s traits
with a standard DMX 512 controller.
2. To run your fixture in DMX mode press the MODE button until
“d.XXX” is displayed. “XXX” represents the current displayed ad dress. Use the UP or DOWN buttons to select your desired DMX
address, then press the SETUP button to select your DMX Channel
mode.
3. Use the UP or DOWN buttons to scroll through the DMX Channel
modes. The Channel modes are listed below:
• To run the 2 Channel Mode, press the MODE button until “Ch02”
is displayed. This is the 2 Channel DMX Mode.
• To run the 3 Channel Mode, press the MODE button until “Ch03”
is displayed. This is the 3 Channel DMX Mode.
• To run the 4 Channel Mode, press the MODE button until “Ch04”
is displayed. This is the 4 Channel DMX Mode.
• To run the 5 Channel Mode, press the MODE button until “Ch05”
is displayed. This is the 5 Channel DMX Mode.
• To run the 8 Channel Mode, press the MODE button until “Ch08”
is displayed. This is the 8 Channel DMX Mode.
• To run the 9 Channel Mode, press the MODE button until “Ch09”
is displayed. This is the 9 Channel DMX Mode.
4. See pages 14-19 for the DMX values and traits of each channel
mode.
5. After you have chosen your desired DMX Channel mode plug in
the fixture via the XLR connections to any standard DMX controller.
WW/CW/A Dimmer Mode:
1. Plug the fixture in and press the MODE button until:
2. When “H.XXX” is displayed you are in Warm White dimming mode.
Press the UP and DOWN buttons to adjust intensity.
3. When “C.XXX” is displayed you are in Cool White dimming mode.
Press the UP and DOWN buttons to adjust intensity.
4. When “A.XXX” is displayed you are in Amber dimming mode. Press
the UP and DOWN buttons to adjust intensity.
5. After you have adjusted the colors to make your desired color you
can then activate strobing by pressing the SET UP button to
enter the strobe mode.
6. “S.XXX” will be displayed, this is strobing mode. The strobing can be
adjusted between “S.000” (strobe off) to “S.015” (fastest strobe).
ADJ Products, LLC - www.adj.com - Flat Par TW12 User Manual Page 8
Sound Active Mode:
In this mode the Flat Par TW12 will react to sound, and chase through
the different colors.
1. Plug the fixture in and press the MODE button until “So-X” is dis-
played. “X” represents the sound active mode (1-8) currently dis-
played.
2. The fixture will now change via sound.
3. To adjust the sound sensivity, press the SET UP button. “SJ-X”
will be displayed. Use the UP or DOWN buttons to adjust the
sensitivity. “SJ-1” is the least sensitive, “SJ-8” is the most sensitive.
Auto Run Mode:
There are 3 types of Auto Run Modes to choose from; Color
Color Change, and both modes running together.
The running
is adjustable in all 3 modes.
1. Plug the fixture in and press the MODE button until either “AF-X”,
“AJ-X”, or “A-JF” is displayed.
• AF-X = Color Fade mode, there are 8 Color Fade modes to choose
from. Use the UP or DOWN buttons to scroll through the different
Auto Fade modes.
• AJ-X = Color Change mode, there are 8 Color Change modes to
choose from. Use the UP or DOWN buttons to scroll through the
different Auto Change modes.
• A-JF = Both Color Fade and Color Change modes running.
2. After you have chosen your desired running mode press the SET UP
button until “SP.XX” is displayed. When this is displayed you can
adjust the running speed of your desired program. Use the UP or
DOWN button to adjust the speed between “SP.01” (slowest) and
“SP.16” (fastest). Once you have set your desired running speed,
press the SET UP button to return to your desired Auto Run Mode.
Fade,
speed
Static Color Mode:
1. Plug the fixture in and press the MODE button until “CLXX” is dis-
played.
2. There are 32 colors to choose from. Select your desired color by
pressing the UP and DOWN buttons. After you have selected your
desired color you can activate strobing by pressing the SET UP but ton to enter the strobe mode.
3. “S.XXX” will be displayed, this is strobing. The strobing can be
adjusted between “S.000” (strobe off) to “S.015” (fastest strobe).
ADJ Products, LLC - www.adj.com - Flat Par TW12 User Manual Page 9
Page 6
Flat Par TW12 Operating Instructions
Flat Par TW12 Operating Instructions
Default Running Mode:
This is a default running mode. When this mode is activated all modes
will return to their default settings.
1. Plug the fixture in and press the MODE button until “dXX” is dis-
played. “XX” represents either “on” or “oFF”.
2. Press the SET UP button until “dEFA” is displayed.
3. Press the UP and DOWN buttons simultaneously. Press the
MODE button to exit.
ADJ LED RC3:
This function is used to activate and deactivate the ADJ LED RC3
(Remote Control). When this function is activated you can control the
fixture using the ADJ LED RC3. Please see the next page for ADJ LED
RC3 controls and functions.
1. Plug the fixture in and press the MODE button until “dXX” is dis-
played. “XX” represents either “on” or “oFF”.
2. Press the SET UP button until “IrXX” is displayed. “XX” represents
either “on” or “oF”.
3. Press the UP or DOWN buttons to either activate the remote func tion (On) or deactivate it (Off).
DMX State:
This mode can be used as a precaution mode, that in case the DMX
signal is lost, the operating mode chosen in the setup is the running
mode the xture will go into when the DMX signal is lost. You can also
set this as the operating mode you would like the unit to return to when
power is applied.
1. Press the MODE button until the DMX address is displayed.
2. Press the SET UP button until “No-X” is displayed. “X” represents
a number between 0-2.
3. Use the UP or DOWN buttons to operating mode you would like
the unit to start up in when power is applied or the DMX signal is
lost.
• “N0-0” (BLACKOUT) - If the DMX signal is lost or power is applied,
the unit will automatically go into stand by mode.
• “N0-1” (HOLD) - If the DMX signal is lost the xture will stay in the
ADJ Products, LLC - www.adj.com - Flat Par TW12 User Manual Page 10
last DMX set up. If power is applied and this mode is set, the unit will
automatically go into the last DMX set up.
• “N0-2” (FADE PROGRAM) - If the DMX signal is lost or power is
applied, the unit will automatically run the fade program.
Dimmer Curve:
This is used to set the dimmer curve used with DMX mode. See the
Dimmer Curve chart on page 20 for more information.
1. Plug the fixture in and press the MODE button until the DMX
address is displayed.
2. Press the ENTER button until “dr-X” is displayed. “X” represents
the current dimming mode.
3. Use the UP and DOWN buttons to find your desired dimmer
curve. Press SET UP when you are finished.
• dr-0 - Standard
• dr-1 - Stage
• dr-2 - TV
• dr-3 - Architectural
• dr-4 - Theater
Flat Par TW12 Master-Slave Configuration
Master-Slave Configuration:
This function will allows you to link units together to run in a Master-Slave
mode. In Master-Slave operation one unit will act as the controlling unit
and the others will react to the controlling units built-in programs. Any
unit can act as a Master or as a Slave however, only one unit can be programmed to act as the “Master.”
Master-Slave Connections and Settings:
1. Daisy chain your units via the XLR connector on the rear of the unit.
Use standard XLR data cables to link your units together. Remember
that the Male XLR connector is the input and the Female XLR con-
nector is the ouput. The first unit in the chain (master) will use the
female XLR connector only. The last unit in the chain will use the
male XLR connector only.
2. Connect the rst “Slave” unit to the “Master.”
3. Set the “Master” unit to your desired mode of operation. For the
“Slave” unit(s) press the MODE button until “SLAv” is displayed. The
“Slave” unit(s) will now follow the “Master”.
ADJ Products, LLC - www.adj.com - Flat Par TW12 User Manual Page 11
Page 7
Flat Par TW12 ADJ LED RC3 Operation
Flat Par TW12 ADJ LED RC3 Operation
The ADJ LED RC3 infrared remote (sold seperately) has many differnet functions and gives you complete control of your Flat Par
TW12. To control the your desired fixture you must aim the controller
at the front of the fixture and be no more the 30 feet away. To use the
ADJ LED RC3 you must first activate the fixtures infrared receiver, to
activate the receiver please see the instructions on page 10.
BLACKOUT - Pressing this button will blackout the fixture.
AUTO RUN - Pressing this button will cycle through the auto run
mode, color fade mode, and color change. You can control the speed
of the 3 modes by pressing the SPEED button first and then pressing
the “+” and “-” buttons. In color fade and color change mode, press
the “+” and “-” buttons to scroll through the 8 modes.
PROGRAM SELECTION - Pressing this button activates static color
mode. Use the “+” or “-” to scroll through the 32 colors. Press Flash
to activate/deactivate strobing. Use the “+” and “-” buttons to adjust
the strobe speed.
DMX MODE - Press this button to cycle between DMX Channel mode
selection, DMX addressing, DMX State, and dimming curve selection.
Each press of this button will change to the next mode.
• In DMX State mode press the the “+” and “-” buttons to scroll
through the DMX state modes. See DMX State on page 10-11 for
more info.
• In DMX address mode press the the “+” and “-” buttons to adjust
the DMX address.
• In dimmer curve setting press the the “+” and “-” buttons to scroll
through the dimmer curves. See Dimmer Curves on page 11 for more
info.
Mode.
• If the Warm White & Amber LED’s glow you are in 8 Channel
Mode.
• If Cool White & Amber LED’s glow you are in 9 Channel Mode.
SOUND ACTIVE - This button activates sound active mode. Use the
“+” and “-” buttons to scroll through the 8 sound active modes. Press
the Speed button and use the “+” and “-” buttons to adjust the sound
sensitivity level.
SLAVE - This designates the fixture as a slave fixture in a master/
slave configuration.
SET ADDRESS - Press this button to set the DMX address. Press
this button first, then press the numbers to set the address.
Note: When setting the DMX address each time a number is pressed
a LED color will glow, when you have set the DMX address correctly
all LED’s will flash 2-3 times.
Example: Set DMX Address 1 Press “S-0-0-1”
Set DMX Address 245 Press “S-2-4-5”
WW CW A - Press either one of these buttons and the press the “+”
or “-” to adjust the output intensity. Press Flash to activate/deactivate
strobing. Use the “+” and “-” buttons to adjust the strobe speed.
• In DMX Channel selection press the the “+” and “-” buttons to scroll
through the different DMX Channel modes. See DMX mode on pages
7-8 for more info. The info below and on the next page will help identify which channel mode you are in.
• If the Warm White LED’s glow you are in 2 Channel Mode.
• If the Cool White LED’s glow you are in 3 Channel Mode.
• If the Amber LED’s glow you are in 4 Channel Mode.
• If the Warm & Cool White LED’s glow you are in 5 Channel
ADJ Products, LLC - www.adj.com - Flat Par TW12 User Manual Page 12
ADJ Products, LLC - www.adj.com - Flat Par TW12 User Manual Page 13
Page 8
Flat Par TW12 2 Channel Mode
Flat Par TW12 5 Channel Mode
Channel Value Function
1 0 - 255 COLOR MACROS
(See the Color Macro chart on page 19)
2 0 - 255 DIMMER 0% - 100%
Flat Par TW12 3 Channel Mode
Channel Value Function
1 WARM WHITE
0 - 255 0% - 100%
2 COOL WHITE
0 - 255 0% - 100%
3 AMBER
0 - 255 0% - 100%
Flat Par TW12 4 Channel Mode
Channel Value Function
1 WARM WHITE
0 - 255 0% - 100%
2 COOL WHITE
0 - 255 0% - 100%
3 AMBER
0 - 255 0% - 100%
4 MASTER DIMMER
0 - 255 0% - 100%
Channel Value Function
1 WARM WHITE
0 - 255 0% - 100%
2 COOL WHITE
0 - 255 0% - 100%
3 AMBER
0 - 255 0% - 100%
4 MASTER DIMMER
0 - 255 0% - 100%
5 STROBING
0 - 31 LED OFF
32 - 63 LED ON
64 - 95 STROBING SLOW - FAST
96 - 127 LED ON
128 - 159 PULSE STROBING SLOW - FAST
160 - 191 LED ON
192 - 223 RANDOM STROBING SLOW - FAST
224 - 255 LED ON
ADJ Products, LLC - www.adj.com - Flat Par TW12 User Manual Page 15ADJ Products, LLC - www.adj.com - Flat Par TW12 User Manual Page 14
Page 9
Flat Par TW12 8 Channel Mode
Flat Par TW12 8 Channel Mode
Channel Value Function
1 WARM WHITE
0 - 255 0% - 100%
2 COOL WHITE
0 - 255 0% - 100%
3 AMBER
0 - 255 0% - 100%
4 MASTER DIMMER
0 - 255 0% - 100%
5 STROBING
0 - 31 LED OFF
32 - 63 LED ON
64 - 95 STROBING SLOW - FAST
96 - 127 LED ON
128 - 159 PULSE STROBING SLOW - FAST
160 - 191 LED ON
192 - 223 RANDOM STROBING SLOW - FAST
224 - 255 LED ON
6 0 - 255 COLOR MACROS
(See the Color Macro chart on page 19)
7 PROGRAMS
0 - 127 NO PROGRAM
128 - 135 COLOR FADE 1
136 - 143 COLOR FADE 2
144 - 151 COLOR FADE 3
152 - 159 COLOR FADE 4
160 - 167 COLOR FADE 5
168 - 175 COLOR FADE 6
176 - 183 COLOR FADE 7
184 - 191 COLOR FADE 8
192 - 199 COLOR CHANGE 1
200 - 207 COLOR CHANGE 2
208 - 215 COLOR CHANGE 3
216 - 223 COLOR CHANGE 4
224 - 231 COLOR CHANGE 5
ADJ Products, LLC - www.adj.com - Flat Par TW12 User Manual Page 16 ADJ Products, LLC - www.adj.com - Flat Par TW12 User Manual Page 17
Channel Value Function
7 PROGRAMS
232 - 239 COLOR CHANGE 6
240 - 247 SOUND ACTIVE MODE 1
248 - 255 SOUND ACTIVE MODE 2
8 PROGRAM SPEED/SOUND SENSITIVE
0 - 255 PROGRAM SPEED SLOW - FAST
0 - 255 SOUND SENSITIVITY MIN - MAX
When channel 6 is being used, channels 1-3 will cannot be
used.
When channel 7 is between the values of 128-239, channel 8
will control the program speed.
When channel 7 is between the values of 240-255, channel 8
will control the sound sensitivity.
Page 10
Flat Par TW12 9 Channel Mode
Flat Par TW12 9 Channel Mode
Channel Value Function
1 WARM WHITE
0 - 255 0% - 100%
2 COOL WHITE
0 - 255 0% - 100%
3 AMBER
0 - 255 0% - 100%
4 MASTER DIMMER
0 - 255 0% - 100%
5 STROBING
0 - 31 LED OFF
32 - 63 LED ON
64 - 95 STROBING SLOW - FAST
96 - 127 LED ON
128 - 159 PULSE STROBING SLOW - FAST
160 - 191 LED ON
192 - 223 RANDOM STROBING SLOW - FAST
224 - 255 LED ON
6 0 - 255 COLOR MACROS
(See the Color Macro chart on page 19)
7 PROGRAMS
0 - 127 NO PROGRAM
128 - 135 COLOR FADE 1
136 - 143 COLOR FADE 2
144 - 151 COLOR FADE 3
152 - 159 COLOR FADE 4
160 - 167 COLOR FADE 5
168 - 175 COLOR FADE 6
176 - 183 COLOR FADE 7
184 - 191 COLOR FADE 8
192 - 199 COLOR CHANGE 1
200 - 207 COLOR CHANGE 2
208 - 215 COLOR CHANGE 3
216 - 223 COLOR CHANGE 4
224 - 231 COLOR CHANGE 5
Channel Value Function
7 PROGRAMS
232 - 239 COLOR CHANGE 6
240 - 247 SOUND ACTIVE MODE 1
248 - 255 SOUND ACTIVE MODE 2
8 PROGRAM SPEED/SOUND SENSITIVE
0 - 255 PROGRAM SPEED SLOW - FAST
0 - 255 SOUND SENSITIVITY MIN - MAX
9 DIMMER CURVES
0 - 20 STANDARD
21 - 40 STAGE
41 - 60 TV
61 - 80 ARCHITECTURAL
81 - 100 THEATRE
101 - 255 DEFAULT TO UNIT CURVE SETTING
* Channels 1, 2, and 3 will not work, when Channel 6 is being used.
* When using Channel 7 values 128-239, Channel 8 will control the speed of the
programs.
* When using Channel 7 values 240-255, Channel 8 will control the sound sensitivity.
Flat Par TW12 Color Macro Chart
ADJ Products, LLC - www.adj.com - Flat Par TW12 User Manual Page 19ADJ Products, LLC - www.adj.com - Flat Par TW12 User Manual Page 18
Page 11
Flat Par TW12 Dimmer Curve Chart
Flat Par TW12 Power Cord Daisy Chain Flat Par TW12 Photometric Chart
With this feature you can connect the xtures to one another
using the IEC input and output sockets. The quantity that can be
connected is 10 xtures maximum. After 10 xtures you will need
to use a new power outlet. They must be the same xtures. DO
NOT mix xtures.
Flat Par TW12 Fuse Replacement
Disconnect the unit from its power source. Remove the power cord
from the unit. Once the cord has been removed, you will find that the
fuse holder is located inside the power socket. Insert a flat-head screw
driver into the power socket and gently pry out the fuse holder. Remove
the bad fuse and replace with a new one. The fuse holder also has a
holder for a spare fuse.
Flat Par TW12 Trouble Shooting
Listed below are a few common problems the user may encounter,
with solutions.
Unit not responding to DMX:
1. Check that the DMX cables are connected properly and are
wired correctly (pin 3 is “hot”; on some other DMX devices
pin 2 may be ‘hot’). Also, check that all cables are connected
to the right connectors; it does matter which way the inputs
and outputs are connected.
Unit does not respond to sound:
1. Quiet or high pitched sounds will not activate the unit.
2. Make sure that Sound Active mode is activated.
Flat Par TW12 Cleaning
Due to fog residue, smoke, and dust cleaning the internal and external optical lenses must be carried out periodically to optimize light
output.
Ramp Effect
Standard
Stage
TV
Architectural
Theatre
(Fade Time) (Fade Time)
1. Use normal glass cleaner and a soft cloth to wipe down the
outside casing.
2. Clean the external optics with glass cleaner and a soft cloth
every 20 days.
3. Always be sure to dry all parts completely before plugging
the unit back in.
Cleaning frequency depends on the environment in which the fixture
operates (i.e. smoke, fog residue, dust, dew).
ADJ Products, LLC - www.adj.com - Flat Par TW12 User Manual Page 20 ADJ Products, LLC - www.adj.com - Flat Par TW12 User Manual Page 21
Page 12
Flat Par TW12 Warranty
MANUFACTURER’S LIMITED WARRANTY
A. ADJ Products, LLC hereby warrants, to the original purchaser, ADJ Products, LLC products
to be free of manufacturing defects in material and workmanship for a prescribed period from
the date of purchase (see specific warranty period on reverse). This warranty shall be valid only if the
product is purchased within the United States of America, including possessions and
territories. It is the owner’s responsibility to establish the date and place of purchase by acceptable
evidence, at the time service is sought.
B. For warranty service you must obtain a Return Authorization number (RA#) before sending back
the product–please contact ADJ Products, LLC Service Department at 800-322-6337. Send the pro duct only to the ADJ Products, LLC factory. All shipping charges must be pre-paid. If the requested repairs
or service (including parts replacement) are within the terms of this warranty, ADJ Products, LLC will pay
return shipping charges only to a designated point within the United States. If the entire instrument is sent,
it must be shipped in it’s original package. No accessories should be shipped with the product. If
any accessories are shipped with the product, ADJ Products, LLC shall have no liability whatsoever for
loss of or damage to any such accessories, nor for the safe return thereof.
C. This warranty is void if the serial number has been altered or removed; if the product is modified in any
manner which ADJ Products, LLC concludes, after inspection, affects the reliability of the product; if the
product has been repaired or serviced by anyone other than the ADJ Products, LLC factory unless prior
written authorization was issued to purchaser by ADJ Products, LLC; if the product is damaged because
not properly maintained as set forth in the instruction manual.
D. This is not a service contract, and this warranty does not include maintenance, cleaning or periodic check
up. During the period specified above, ADJ Products, LLC will replace defective parts at its expense
with new or refurbished parts, and will absorb all expenses for warranty service and repair labor by
reason of defects in material or workmanship. The sole responsibility of ADJ Products, LLC under this
warranty shall be limited to the repair of the product, or replacement thereof, including parts, at the sole
discretion of ADJ Products, LLC. All products covered by this warranty were manufactured after August
15, 2012, and bear indentifying marks to that effect.
Flat Par TW12 Notes
E. ADJ Products, LLC reserves the right to make changes in design and/or improvements upon it’s products
without any obligation to include these changes in any products theretofore manufactured.
No warranty, whether expressed or implied, is given or made with respect to any accessory supplied with
products described above. Except to the extent prohibited by applicable law, all implied warranties made
by ADJ Products, LLC in connection with this product, including warranties of merchantability or fitness,
are limited in duration to the warranty period set forth above. And no warranties, whether expressed or
implied, including warranties of merchantability or fitness, shall apply to this product after said period
has expired. The consumer’s and/or Dealer’s sole remedy shall be such repair or replacement as is
expressly provided above; and under no circumstances shall ADJ Products, LLC be liable for any loss or
damage, direct or consequential, arising out of the use of, or inability to use, this product.
This warranty is the only written warranty applicable to ADJ Products, LLC Products and
supersedes all prior warranties and written descriptions of warranty terms and conditions heretofore
published. This warranty was revised after December 1, 2012.
MANUFACTURER’S LIMITED WARRANTY PERIODS:
•LightingProducts=1-year(365days)LimitedWarranty(Such as: Special Effect Lighting, Intelligent
Lighting, UV lighting, Strobes, Fog Machines, Bubble Machines, Mirror Balls, Par Cans, Trussing,
Lighting Stands etc. excluding LEDs and lamps)
•LaserProducts=90-DayLimitedWarranty
•L.E.D.Products=2-year(730days)LimitedWarranty(excluding motors, PCB boards, and power
supplies, which have a 1-year (365 day Limited Warranty) and batteries which have a 180 day
limited warranty).
ADJ Products, LLC - www.adj.com - Flat Par TW12 User Manual Page 22
ADJ Products, LLC - www.adj.com - Flat Par TW12 User Manual Page 23
Page 13
Flat Par TW12 Notes
Flat Par TW12 Notes
ADJ Products, LLC - www.adj.com - Flat Par TW12 User Manual Page 24
ADJ Products, LLC - www.adj.com - Flat Par TW12 User Manual Page 25
Page 14
Flat Par TW12 Specifications
Model:
Voltage: 100V ~ 240V/50~60Hz
LEDs: 12 x 5W 3-in-1 Tri LED’s
Beam Angle: 40 Degrees
Working Position: Any safe working position
Power Draw: 61W
Power Cord Daisy Chain: 10 Fixtures Max.
Fuse: 2A
Weight: 7lbs./ 3.25Kgs.
Dimensions: 13” (L) x 11” (W) x 4” (H)
328 x 280 x 105mm
Colors: Warm White, Cool White, & Amber
DMX Channels: 6 DMX Modes: 2 Channel Mode,
3 Channel Mode, 4 Channel Mode,
5 Channel Mode, 8 Channel Mode
& 9 Channel Mode
Warranty: 2 Year (730 days)
Color Temperature
Variable: 2700-6500
Cool White: >6500°K
Warm White: >2700°K
Amber (Wavelength): 590-595NM
Flat Par TW12
CRI Values
Cool White: 70-80
Warm White: 70-80
Amber: None
Auto Sensing Voltage: This xture contains a automatic voltage
switch, which will auto sense the voltage when it is plugged into
the power source.
Please Note: Specications and improvements in the design of
this unit and this manual are subject to change without any prior
written notice.
ADJ Products, LLC - www.adj.com - Flat Par TW12 User Manual Page 26
ADJ Products, LLC
6122 S. Eastern Ave. Los Angeles, CA 90040 USA
Tel: 323-582-2650 / Fax: 323-725-6100
Web: www.adj.com / E-mail: info@americandj.com
A.D.J. Supply Europe B.V.
Junostraat 2
6468 EW Kerkrade
Netherlands
service@adjgroup.eu / www.adj.com
Tel: +31 45 546 85 00 / Fax: +31 45 546 85 99
Loading...