ADJ Entourage User Manual [EN]

EntouragE

©2016 ADJ Products, LLC all rights reserved. Information,

specications, diagrams, images, and instructions herein are
subject to change without notice. ADJ Products, LLC logo and
identifying product names and numbers herein are trademarks
of ADJ Products, LLC. Copyright protection claimed includes all
forms and matters of copyrightable materials and information
now allowed by statutory or judicial law or hereinafter granted.
Product names used in this document may be trademarks or
registered trademarks of their respective companies and are
hereby acknowledged. All non-ADJ Products, LLC brands and
product names are trademarks or registered trademarks of their

respective companies.

ADJ Products, LLC and all aliated companies hereby dis­claim any and all liabilities for property, equipment, building, and
electrical damages, injuries to any persons, and direct or indi­rect economic loss associated with the use or reliance of any
information contained within this document, and/or as a result
of the improper, unsafe, unsucient and negligent assembly,
installation, rigging, and operation of this product.

Caution: Fog Machines may set o Smoke Alarms!

User Instructions

8/16

Europe Energy Saving Notice
Energy Saving Matters (EuP 2009/125/EC)
Saving electric energy is a key to help protecting the enviroment.
Please turn o all electrical products when they are not in use. To
avoid power consumption in idle mode, disconnect all electrical
equipment from power when not in use. Thank you!

Entourage Introduction

Entourage Safety Precautions

Introduction: Congratulations, you have just purchased one of the

most reliable fog machines on the market today! The Entourage faze
machine have been designed to perform reliably for years when the
guidelines in this booklet are followed. Please read and understand the

instructions in this manual carefully and thoroughly before attempting
to operate this unit. These instructions contain important information
regarding safety during use and maintenance.

Customer Support: ADJ Products, LLC provides a toll free customer

support line, to provide set up help and to answer any question should
you encounter problems during your set up or initial operation. You
may also visit us on the web at www.adj.com for any comments or
suggestions. For service related issue please contact ADJ Products,
LLC. Service Hours are Monday through Friday 8:00 a.m. to 4:30 p.m.
Pacic Standard Time.
Voice: [phone]
Fax: [phone]
E-mail: [e-mail]

To purchase parts online visit http://parts.americandj.com

Warning! To prevent or reduce the risk of electrical shock or re, do

not expose this unit to rain or moisture.

Caution! There are no user serviceable parts inside this unit. Do not

attempt any repairs yourself, doing so will void your manufactures war­ranty. In the unlikely event your unit may require service please contact
ADJ Products, LLC.

Do not discard the shipping cartoon in the trash. Please recycle when
ever possible.

SAFETY ISSUES:

NEVER POINT OR AIM A FOG MACHINE TOWARDS PEOPLE OR
THEIR CLOTHING. THIS UNIT EMITS HOT VAPOR AND SHOULD
BE USED WITH THE SAME CARE THAT YOU WOULD OBSERVE
WHEN USING AN ELECTRIC KETTLE OR IRON.

Please Note: Specications and improvements in the design of
this unit and this manual are subject to change without any prior
written notice.

• Be sure to save the packing carton in the unlikely event the unit
may have to be returned for service

• Do not spill water or other liquids into or on to your fogger. Be
sure that all the fog uid is kept inside the uid reservoir

• Be sure that the local power outlet match that or the required
voltage for your fog machine

• Do not remove the top cover under any conditions. There are no
user serviceable parts inside

• Disconnect the unit’s main power when left unused for long peri-

ods of time

• Never connect this unit to a dimmer pack

• Do not attempt to operate this unit, if it becomes damaged in anyway

• Never operate this unit when it’s cover is removed

• To reduce the risk of electrical shock or re, do not expose this
unit rain or moisture

• Do not attempt to operate this unit if the power cord has been fray­ ed or broken. Do not attempt to remove or break o the ground
prong from the electrical cord. This prong is used to reduce the
risk of electrical shock and re in case of an internal short

• Disconnect from main power before making any type of connection

• Never block the ventilation holes. Always be sure to mount this
unit in an area that will allow proper ventilation. Allow about 6”
(15cm) between this device and a wall

• This unit is intended for indoor use only, use of this product out­ doors voids all warranties

• Always mount this unit in a safe and stable matter

• Please route your power cord out of the way of foot trac. Power
cords should be routed so they are not likely to be walked on,
pinched by items placed upon or against them

• The unit should only be serviced by qualified service personnel
when:
A. The power-supply cord or the plug has been damaged.
B. Objects have fallen, or liquid has been spilled into the unit.
C. The unit has been exposed to rain or water.
D. The appliance does not appear to operate normally or
exhibits a marked change in performance.

ADJ Products, LLC - www.adj.com - Entourage Instruction Manual Page 2

ADJ Products, LLC - www.adj.com - Entourage Instruction Manual Page 3

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

DMX512

DMX+,DMX-,COMMON

1

2

3

Termination reduces signal errors and
avoids signal transmission problems
and interference. It is always advisable
to connect a DMX terminal, (Resistance
120 Ohm 1/4 W) between PIN 2 (DMX-)
and PIN 3 (DMX +) of the last fixture.

POWER

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

and PIN 3 (DMX +) of the last fixture.

Entourage DMX Information Entourage DMX Information

Power Supply: Before plugging your unit in, be sure the source volt-

age in your area matches the required voltage for your ADJ Entourage.
The ADJ Entourage is available in a 120v and 230v version. Because
line voltage may vary from venue to venue, you should be sure your
unit voltage matches the wall outlet voltage before attempting to oper­ate you xture.

DMX-512: DMX is short for Digital Multiplex. This is a universal pro-

tocol used as a form of communication between intelligent fixtures
and controllers. A DMX controller sends DMX data instructions from
the controller to the fixture. DMX data is sent as serial data that trav­els from fixture to fixture via the DATA “IN” and DATA “OUT” XLR ter­minals located on all DMX fixtures (most controllers only have a DATA
“OUT” terminal).

DMX Linking: DMX is a language allowing all makes and models of
dierent manufactures to be linked together and operate from a single
controller, as long as all xtures and the controller are DMX compli­ant. To ensure proper DMX data transmission, when using several
DMX fixtures try to use the shortest cable path possible. The order
in which fixtures are connected in a DMX line does not influence the
DMX addressing. For example; a fixture assigned a DMX address of 1
may be placed anywhere in a DMX line, at the beginning, at the end,
or anywhere in the middle. When a fixture is assigned a DMX address
of 1, the DMX controller knows to send DATA assigned to address 1
to that unit, no matter where it is located in the DMX chain.

Data Cable (DMX Cable) Requirements (For DMX Operation):

The Entourage can be controlled via DMX-512 protocol. The Entourage
has 3 DMX channel modes, 1 channel, 2 channel, and 4 channel. The
DMX address is set on the back panel. Your unit and your DMX con­troller require a standard 3-pin XLR connector for
data input and data output (Figure 1). We recom­mend Accu-Cable DMX cables. If you are making
your own cables, be sure to use standard 110-120
Ohm shielded cable (This cable may be purchased
at almost all pro lighting stores). Your cables should
be made with a male and female XLR connector on
either end of the cable. Also remember that DMX

cable must be daisy chained and cannot be split.

ADJ Products, LLC - www.adj.com - Entourage Instruction Manual Page 4 ADJ Products, LLC - www.adj.com - Entourage Instruction Manual Page 5

Figure 1

Notice: Be sure to follow gures two and three when making your own

cables. Do not use the ground lug on the XLR connector. Do not con­nect the cable’s shield conductor to the ground lug or allow the shield
conductor to come in contact with the XLR’s outer casing. Grounding
the shield could cause a short circuit and erratic behavior.

COMMON

1

DMX512 IN

3

3-PIN XLR

2

Figure 2

XLR Pin Conguration

1 Ground

Pin 1 = Ground

Pin 2 = Data Compliment (negative)

Pin 3 = Data True (positive)

When longer runs of cable are

Figure 4

Pin 1

Pin 2

Pin 3

Do Not Use

Do Not Use

XLR Male Socket

1 Ground

DMX512 OT

3-PIN XLR

2 Cold

3 Hot

1

3

2

DMX +

DMX -

XLR Female Socket

2 Cold

3 Hot

Figure 3

Special Note: Line Termination.

used, you may need to use a terminator on the last unit to avoid erratic
behavior. A terminator is a 110-120 ohm 1/4 watt resistor which is con­nected between pins 2 and 3 of a male XLR connector (DATA + and
DATA -). This unit is inserted in the female XLR connector of the last
unit in your daisy chain to terminate the line. Using a cable terminator
(ADJ part number Z-DMX/T) will decrease the possibilities of erratic
behavior.

5-Pin XLR DMX Connectors.

512 data cables for DATA transmission in place of 3-pin. 5-pin DMX
xtures may be implemented in a 3-pin DMX line. When inserting stan­dard 5-pin data cables in to a 3-pin line a cable adaptor must be used,
these adaptors are readily available at most electric stores. The chart
below details a proper cable conversion.

Conductor 5-Pin XLR Male (In)3-Pin XLR Female (Out)

Ground/Shield

Data Compliment (- signal)

Data True (+ signal)

Not Used

Not Used

Termination reduces signal errors and

1

avoids signal transmission problems

3

and interference. It is always advisable

2

to connect a DMX terminal, (Resistance
120 Ohm 1/4 W) between PIN 2 (DMX-)

Some manufactures use 5-pin DMX-

3-Pin XLR to 5-Pin XLR Conversion

Pin 1

Pin 2

Pin 3

Entourage Layout

Entourage CAD Drawing

A. Flight Case
B. Unique Anti-Spill Tank
C. Quick Connector
D. Blue LCD Screen
E. 6 Buttons of Control
F. DMX 5-Pin XLR Output
G. DMX 5-Pin XLR Input

H. DMX 3-Pin XLR Output
I. DMX 3-Pin XLR Input
J. Breaker
K. PowerCon Input
L. Fog Output Deector
M. Sponge

21”/533mm

9.8”/249mm

15.2”/387mm

Entourage General Set-Up

1. Open the shipping carton and carefully remove the unit from the shipping

carton.

2. Be sure to remove all the packing material especially around the nozzle.

3. Set the fog machine on a flat dry surfaceand fill the fog fluid reservoir with
American DJ brand fog juice. Place the feeder tube with the filter deep

inside the reservoir and tighten the cap.

4. Plug the unit in to a matching power supply and the unit will begin to heat
up. Wait about 45 seconds for the fogger to reach normal operating
temperature.

5. Follow the operating instructions on the next pages for proper operation.

ADJ Products, LLC - www.adj.com - Entourage Instruction Manual Page 6 ADJ Products, LLC - www.adj.com - Entourage Instruction Manual Page 7

Entourage Control Panel

Warming

Up……

DMX set

Addr- xxx

DMX set

Addr- xxx

Version:

1.0

Warming

Up……

DMX set

Addr- xxx

--> Dura xxx
Intv xxx

Dura xxx

--> Intv xxx

Warming

Up……

DMX set

Addr- xxx

Dura xxx

--> Intv xxx

DMX set

Addr- xxx

Version:

1.0

Warming

Up……

DMX set

Addr- xxx

DUR. xxx

INT. xxx

--> Dura xxx
Intv xxx

Dura xxx

--> Intv xxx

(Stop)

Cleaning

DMX set

Addr- xxx

Warming

Up……

DMX set

Addr- xxx

--> Dura xxx
Intv xxx

Dura xxx

--> Intv xxx

DMX set

Addr- xxx

Entourage Operation

TIMER OPERATION:

Increasing numerical value for Function

Fan Speed
& Volume Adjustment

Timer Fog,
adjustable by Function Button

Constant Fog, adjustable by Function Button

Entourage Start Up

Decreasing numerical value
for Function

Manual Fog,
Max. Fan Speed & Volume

START UP:

1. Connect the provided PowerCon cable to the fog machine
input. Then plug the power cord into a matching power
source. There is no ON/OFF switch.

2. Primary power is now “On”.

Version:

1.0

3. 2 Seconds after power is applied the unit
will begin to warm up.

Warming

Up……

1. Press the TIMER button to enter the fog

timer operation.

DUR. xxx

INT. xxx

2. Press the FUNCTION button to enter the timer settings menu.

3. Use the UP or DOWN buttons to adjust

--> Dura xxx

duration (output) time, 3s-250s.

Intv xxx

4. Press the FUNCTION button to switch to interval adjustment.

5. Use the UP or DOWN buttons to adjust
interval (pause) time, 5s-250s.

6. Press the TIMER button again to activate the
timer function. Press the TIMER button
again to deactivate the timer function.

7. When you stop Timer operation the display
will read (Stop) Cleaning. This will take
about 15 seconds.

8. After cleaning is done, the DMX setting
display will show.

Dura xxx

--> Intv xxx

DUR. xxx

INT. xxx

(Stop)

Cleaning

DMX set

Addr- xxx

4. After the unit has warmed up, the last function that was oper­ating before power was shut o will be displayed again. Exam-
ple: If the Timer function was active that will be displayed.

ADJ Products, LLC - www.adj.com - Entourage Instruction Manual Page 8 ADJ Products, LLC - www.adj.com - Entourage Instruction Manual Page 9

Entourage Operation

Version:

1.0

Warming

Up……

DMX set

Addr- xxx

DUR. xxx

INT. xxx

--> Dura xxx
Intv xxx

Dura xxx

--> Intv xxx

DUR. xxx

INT. xxx

(Stop)

Cleaning

DMX set

Addr- xxx

--> Vol xxx

Fan xxx

Vol xxx

--> Fan xxx

Version:

1.0

Warming

Up……

DMX set

Addr- xxx

DUR. xxx

INT. xxx

--> Dura xxx
Intv xxx

Dura xxx

--> Intv xxx

DUR. xxx

INT. xxx

(Stop)

Cleaning

DMX set

Addr- xxx

--> Vol xxx

Fan xxx

Vol xxx

--> Fan xxx

DMX set

Addr- xxx

Dura xxx

--> Intv xxx

DMX set

Addr- xxx

Warming

Up……

DMX set

Addr- xxx

--> Dura xxx
Intv xxx

Dura xxx

--> Intv xxx

DMX set

Addr- xxx

DMX set

Addr- xxx

Dura xxx

--> Intv xxx

DMX set

Addr- xxx

Vol xxx

--> Fan xxx

Warming

Up……

DMX set

Addr- xxx

--> Dura xxx
Intv xxx

Dura xxx

--> Intv xxx

DMX set

Addr- xxx

Entourage Operation

CONTINUOUS FOGGING:

1. Press the HOLD button to start continuous
fogging. NOTE: Fogging will start right
away.

2. Use the UP or DOWN buttons to adjust
output volume, 5%-100%.

--> Vol xxx

Fan xxx

--> Vol xxx

Fan xxx

3. Press the FUNCTION button to switch to Fan adjustment.

4. Use the UP or DOWN buttons to adjust

Vol xxx

Fan speed, 5%-100%.

--> Fan xxx

5. Press the HOLD button again to stop continuous fogging.

6. When you stop continuous fogging the
display will read (Stop) Cleaning. This will
take about 15 seconds.

(Stop)

Cleaning

MANUAL FOGGING:

1. Press the MANUAL button (without releas­ ing). The machine will output at maximum
level and maximum fan speed. Release the

Manual

V100 F100

button to stop fogging.

2. When you stop fogging the display will read
(Stop) Cleaning. This will take about 15 sec-

onds.

3. After cleaning is done, the DMX setting
display will show.

(Stop)

Cleaning

DMX set

Addr- xxx

7. After cleaning is done, the DMX setting
display will show.

DMX set

Addr- xxx

ADJ Products, LLC - www.adj.com - Entourage Instruction Manual Page 10 ADJ Products, LLC - www.adj.com - Entourage Instruction Manual Page 11

Entourage DMX Mode

DMX set

Addr- xxx

Dura xxx

--> Intv xxx

DMX set

Addr- xxx

Vol xxx

--> Fan xxx

Manual

V100 F100

DMX set

Addr- xxx

Warming

Up……

DMX set

Addr- xxx

--> Dura xxx
Intv xxx

Dura xxx

--> Intv xxx

(Stop)

Cleaning

DMX set

Addr- xxx

--> Vol xxx

Fan xxx

Vol xxx

--> Fan xxx

DMX set

Addr- xxx

Manual

V100 F100

*Hold

TimeSet

DMX set

Addr- xxx

4ch.Axxx

VxxxFxxx

Version:

1.0

Warming

Up……

DMX set

Addr- xxx

DUR. xxx

INT. xxx

--> Dura xxx
Intv xxx

Dura xxx

--> Intv xxx

DUR. xxx

INT. xxx

(Stop)

Cleaning

DMX set

Addr- xxx

--> Vol xxx

Fan xxx

--> Vol xxx

Fan xxx

Vol xxx

--> Fan xxx

(Stop)

Cleaning

DMX set

Addr- xxx

Manual

V100 F100

DMX set

Addr- xxx

*Hold

TimeSet

DMX set

Addr- xxx

2ch.Axxx

VxxxFxxx

4ch.Axxx
VxxxFxxx

Version:

1.0

Warming

Up……

DMX set

Addr- xxx

DUR. xxx

INT. xxx

--> Dura xxx
Intv xxx

Dura xxx

--> Intv xxx

DUR. xxx

INT. xxx

(Stop)

Cleaning

DMX set

Addr- xxx

--> Vol xxx

Fan xxx

--> Vol xxx

Fan xxx

Vol xxx

--> Fan xxx

(Stop)

Cleaning

DMX set

Addr- xxx

Manual

V100 F100

DMX set

Addr- xxx

*Hold

TimeSet

DMX set

Addr- xxx

1ch.Axxx

VxxxFxxx

2ch.Axxx

VxxxFxxx

4ch.Axxx
VxxxFxxx

4ch.Axxx

VxxxFxxx

Entourage 1 Channel Mode

DMX Mode:

The Entourage has 3 DMX channel modes; 1 channel mode, 2
channel mode, and 4 channel mode. See page 13 for the DMX

traits.

1. This function will allow you to control each individual fix-
ture’s traits with a standard DMX 512 controller.

2. When the display is showing the DMX setting screen, use
the UP or DOWN buttons to find your desired DMX address.

DMX set

Addr- xxx

3. To run your fixture in DMX mode you must FIRST plug in the
fixture via the XLR connections to any standard DMX con-

troller.

4. Once you have the controller connected to the unit you will
be able to select your desired DMX channel mode. Press the
FUNCTION button to cycle through the DMX channel

modes.

1ch.Axxx

VxxxFxxx

2ch.Axxx

VxxxFxxx

4ch.Axxx

VxxxFxxx

5. When 4 channel mode is selected, after about 5 seconds the
screen will change to the display shown below.

VxxxFxxx

• A = The current DMX address

DxxxIxxx

• V = The current output volume

• F = The current fan speed

• D = The current duration setting

• I = The current interval setting
NOTE: Duration and Interval setting is only available in 4
Channel mode.

ADJ Products, LLC - www.adj.com - Entourage Instruction Manual Page 12 ADJ Products, LLC - www.adj.com - Entourage Instruction Manual Page 13

Channel Value Function

1 OUTPUT VOLUME & FAN SPEED

0 - 4 0% OUTPUT VOLUME
5% FAN SPEED
5 - 255 5%-100% OUTPUT VOLUME
100% FAN SPEED

Entourage 2 Channel Mode

Channel Value Function

1 OUTPUT VOLUME
0 - 4 0% OUTPUT VOLUME
5 - 255 5%-100% OUTPUT VOLUME
2 FAN SPEED
0 - 15 5% FAN SPEED
16 - 255 6%-100% FAN SPEED

Note: In 2 channel mode, when using channel 1 only, the default
fan speed is 30%.

Entourage 4 Channel Mode

Channel Value Function

1 OUTPUT VOLUME
0 - 4 0% OUTPUT VOLUME
5 - 255 5%-100% OUTPUT VOLUME
2 FAN SPEED
0 - 15 5% FAN SPEED
16 - 255 6%-100% FAN SPEED
3 DURATION
0 - 7 3 SECONDS
8 - 255 3-250 SECONDS
4 INTERVAL
0 - 9 0 SECONDS
10 - 255 5-250 SECONDS
Note: In 4 channel mode, when using channel 1 only, the default
fan speed is 30%.

Entourage Maintenance Entourage Maintenance

The uid cannot get dirty. Always make sure the cap is clean
and the fog uid line. Periodically nozzle maybe come clogged
by impurities contact ADJ customer service for a replacement
nozzle.

With prolonged use, the ight case side air lter can accumulate
dust. Perodically remove the ight case side cover and remove
the air lter to clean. After cleaning, be sure to dry the air lter,
an reinstall the lter and cover. If you would like to replace the
air lter, contact ADJ customer service.

With prolonged use, the the sponge inside the vent may accu­mulate oil. Periodically clean the sponge or replace with a new
one. If you would like to replace the sponge, contact ADJ cus-

tomer service.

When storing your fog machine be sure to store it in a cool area.
Cover the machine so that dust does not build up on the unit. When

storing the machine for long periods of time, it is highly advised to at

least run the machine every 3-4 months. Long periods of inactivity
can severly shorten the life of your machine. Only run water based
fog juice through your machine. Never run plain water, vinegar, or any
other liquid solution through your machine. Running anything other
then water based fog juice will severly damage your machine.

ADJ Products, LLC - www.adj.com - Entourage Instruction Manual Page 14

ADJ Products, LLC - www.adj.com - Entourage Instruction Manual Page 15

Entourage Warranty Registration

The Entourage fog machine carries a one year (365 days) limited war­ranty. Please fill out the enclosed warranty card to validate your pur­chase. All returned service items whether under warranty or not, must
be freight pre-paid and accompany a return authorization (R.A.) num­ber. The R.A. number must be clearly written on the outside of the
return package. A brief description of the problem as well as the R.A.
number must also be written down on a piece of paper and included
in the shipping container. If the unit is under warranty, you must pro­vide a copy of your proof of purchase invoice. You may obtain a R.A.
number by contacting customer support at [phone].

Entourage Trouble Shooting

When this message is flashing it means either
the heater is to hot or a thermo sensor is cut.

Heater

Overheat

When this message is flashing it means the
unit is uable to heat.

No

Heating

When this message is flashing it mean either
the unit is out of fluid or the pump is not
pumping.

If you experience low fog output, pump noise, or no fog output at
all, disconnect and discontinue use immediately. Do not attempt to
continue pushing the remote control’s activation button as this may
damage the fog machine. Check the fluid level, the breaker, and be
sure the wall outlet is sending power. If all of the above appears to be
okay, and the unit fails to operate correctly, the unit will require ser­vice. Please contact ADJ Products, LLC.

No

Fluid

ADJ Products, LLC - www.adj.com - Entourage Instruction Manual Page 16 ADJ Products, LLC - www.adj.com - Entourage Instruction Manual Page 17

Entourage Warranty

MANUFACTURER’S LIMITED WARRANTY

A. ADJ Products, LLC hereby warrants, to the original purchaser, ADJ Products, LLC products
to be free of manufacturing defects in material and workmanship for a prescribed period from
the date of purchase (see specific warranty period on reverse). This warranty shall be valid only if the
product is purchased within the United States of America, including possessions and
territories. It is the owner’s responsibility to establish the date and place of purchase by acceptable
evidence, at the time service is sought.

B. For warranty service you must obtain a Return Authorization number (RA#)
before sending back the product–please contact ADJ Products, LLC Service Department
at 800-322-6337. Send the product only to the ADJ Products, LLC factory. All
shipping charges must be pre-paid. If the requested repairs or service (including
parts replacement) are within the terms of this warranty, ADJ Products, LLC will pay return
shipping charges only to a designated point within the United States. If the entire instrument is
sent, it must be shipped in it’s original package. No accessories should be shipped with the product. If
any accessories are shipped with the product, ADJ Products, LLC shall have no liability whatsoever for
loss of or damage to any such accessories, nor for the safe return thereof.

C. This warranty is void if the serial number has been altered or removed; if the product is modified in any
manner which ADJ Products, LLC concludes, after inspection, affects the reliability of the product; if the
product has been repaired or serviced by anyone other than the ADJ Products, LLC factory unless prior
written authorization was issued to purchaser by ADJ Products, LLC; if the product is damaged because
not properly maintained as set forth in the instruction manual.

D. This is not a service contract, and this warranty does not include maintnance, cleaning or periodic check
up. During the period specified above, ADJ Products, LLC will replace defective parts at its expense
with new or refurbished parts, and will absorb all expenses for warranty service and repair labor by
reason of defects in material or workmanship. The sole responsibility of ADJ Products, LLC under this
warranty shall be limited to the repair of the product, or replacement thereof, including parts, at the sole
discretion of ADJ Products, LLC. All products covered by this warranty were manufactured after August
15, 2012, and bear indentifying marks to that effect.

E. ADJ Products, LLC reserves the right to make changes in design and/or improvements upon its products
without any obligation to include these changes in any products theretofore manufactured.

No warranty, whether expressed or implied, is given or made with respect to any accessory supplied with
products described above. Except to the extent prohibited by applicable law, all implied warranties made
by ADJ Products, LLC in connection with this product, including warranties of merchantability or fitness,
are limited in duration to the warranty period set forth above. And no warranties, whether expressed or
implied, including warranties of merchantability or fitness, shall apply to this product after said period
has expired. The consumer’s and/or Dealer’s sole remedy shall be such repair or replacement as is
expressly provided above; and under no circumstances shall ADJ Products, LLC be liable for any loss or
damage, direct or consequential, arising out of the use of, or inability to use, this product.

This warranty is the only written warranty applicable to ADJ Products, LLC Products and
supersedes all prior warranties and written descriptions of warranty terms and conditions heretofore
published.

MANUFACTURER’S LIMITED WARRANTY PERIODS:

 •LightingProducts=1-year(365days)LimitedWarranty(Such as: Special Effect Lighting, Intelligent

Lighting, UV lighting, Strobes, Fog Machines, Bubble Machines, Mirror Balls, Par Cans, Trussing,
Lighting Stands etc. excluding LED and lamps)

 •LaserProducts=1Year(365Days)LimitedWarranty(excluding laser diodes which have a 6 month

limited warranty)

 •L.E.D.Products=2-year(730days)LimitedWarranty(excluding motors, PCB boards, and power
supplies, which have a 1-year (365 day Limited Warranty) batteries which have a 180 day limited war-

ranty). Only the L.E.D.s carry a 2-year warranty (excludingStarTecSerieswhichacarriesa1Year

LimitedWarranty)Note:2YearWarrantyonlyappliestopurchaseswithintheUnitedStates.

•ADJDMXControllers=2Year(730Days)LimitedWarranty(excluding faders and tact switches)

Entourage Specifications

MODEL - Entourage

VOLTAGE*: 120v or 230V, 50/60Hz
HEATER: 1400W
POWER CONSUMPTION: 1500W
WEIGHT: 47 Lbs. / 21.3 Kgs
DIMENSIONS: 21" x 15.25” x 9.75”

533 x 387 x 249 mm

BREAKER: NFB 16A (120V) / 10A (230V)
WARM UP TIME: 45 Seconds
TANK CAPACITY: 5.6 Liter
OUTPUT: 1500 cubic feet per minute
FLUID TYPE: Water Based American DJ Fog Juice
DMX CHANNELS: 3 DMX Channel Modes: 1/2/4
DUTY CYCLE: Not to exceed 6 hours turned on.

*Voltage is preset at the factory and may not be changed

ADJ Products, LLC - www.adj.com - Entourage Instruction Manual Page 18

ADJ Products, LLC

6122 S. Eastern Ave. Los Angeles, CA 90040 USA

Tel: [phone] / Fax: [phone]

Web: www.adj.com / E-mail: [e-mail]

A.D.J. Supply Europe B.V.

Junostraat 2

6468 EW Kerkrade

Netherlands

[e-mail] / www.adj.eu

Tel: [phone] / Fax: [phone]