ADJ Encore Profile WW Users Manual

Page 1
EncorE ProfilE 1000 WW
©2016 ADJ Products, LLC all rights reserved. Information,
specications, diagrams, images, and instructions herein are subject to change without notice. ADJ Products, LLC logo and identifying product names and numbers herein are trademarks of ADJ Products, LLC. Copyright protection claimed includes all forms and matters of copyrightable materials and information now allowed by statutory or judicial law or hereinafter granted. Product names used in this document may be trademarks or registered trademarks of their respective companies and are hereby acknowledged. All non-ADJ Products, LLC brands and product names are trademarks or registered trademarks of their
respective companies.
ADJ Products, LLC and all aliated companies hereby dis­claim any and all liabilities for property, equipment, building, and electrical damages, injuries to any persons, and direct or indirect economic loss associated with the use or reliance of any information contained within this document, and/or as a result of the improper, unsafe, unsucient and negligent as­sembly, installation, rigging, and operation of this product.
Rev. 8/16
User Instructions
Europe Energy Saving Notice Energy Saving Matters (EuP 2009/125/EC) Saving electric energy is a key to help protecting the enviroment. Please turn o all electrical products when they are not in use. To avoid power consumption in idle mode, disconnect all electrical equipment from power when not in use. Thank you!
Page 2
Encore Profile 1000 WW Introduction
Encore Profile 1000 WW Features
Unpacking:
by ADJ Products, LLC. Every Encore Prole 1000 WW has been thoroughly tested and has been shipped in perfect operating condi­tion. Carefully check the shipping carton for damage that may have occurred during shipping. If the carton appears to be damaged, care­fully inspect your xture for any damage and be sure all accessories necessary to operate the unit has arrived intact. In the case damage has been found or parts are missing, please contact our toll free cus­tomer support number for further instructions. Do not return this unit to your dealer without rst contacting customer support.
Introduction:
high powered LED follow spot. This follow spot has three operating modes: white dimmer mode, fade mode, and DMX control mode. This xture can be used in a stand alone mode or connected in a Master/ Slave conguration. To optimize the performance of this product, please read these operating instructions carefully to familiarize yourself with the basic operations of this unit. These instructions contain impor­tant safety information regarding the use and maintenance of this unit. Please keep this manual with the unit, for future reference.
Customer Support: ADJ Products, LLC provides a customer support line, to provide set up help and to answer any question should you encounter problems during your set up or initial operation. You may also visit us on the web at www.adj.com for any comments or sugges­tions. Service Hours are Monday through Friday 8:00 a.m. to 4:30 p.m. Pacic Standard Time. Voice: (323) 582-3322 Fax: (323) 582-3108 E-mail: support@AmericanDJ.com
Thank you for purchasing the Encore Prole 1000 WW
The ADJ Encore Profile 1000 WW is a DMX intelligent,
Warning! To prevent or reduce the risk of electrical shock or re, do
not expose this unit to rain or moisture.
Caution! There are no user serviceable parts inside this unit. Do not
attempt any repairs yourself, doing so will void your manufactures war­ranty. In the unlikely event your unit may require service please contact ADJ Products, LLC.
PLEASE recycle the shipping carton when ever possible.
• Three Operating Modes
• Electronic Dimming 0-100%
• 5 Selectable Dimming Curves
• 4 Included Gobos
• DMX-512 protocol
• 3-Pin & 5-Pin DMX Connections
• 3 DMX Modes: 1 Channel Mode, 2 Channel Mode, & 3 Channel Mode.
• ADJ LED RC2, ADJ UC IR, (Not Included) & Airstream IR compat­ ible
• Power Cord Daisy Chain (See page 17)
Encore Profile 1000 WW Warranty Registration
The Encore Profile 1000 WW carries a 2 year limited warranty. Please fill out the enclosed warranty card to validate your purchase. All returned service items whether under warranty or not, must be freight pre-paid and accompany a return authorization (R.A.) number. The R.A. number must be clearly written on the outside of the return pack­age. A brief description of the problem as well as the R.A. number must also be written down on a piece of paper included in the ship­ping carton. If the unit is under warranty, you must provide a copy of your proof of purchase invoice. You may obtain a R.A. number by con­tacting our customer support team on our customer support number. All packages returned to the service department not displaying a R.A. number on the outside of the package will be returned to the shipper.
Encore Profile 1000 WW Installation
The unit should be mounted using a mounting clamp (not provided), axing it to the mounting bracket that is provided with the unit. Always ensure that the unit is rmly xed to avoid vibration and slip­ping while operating. Always ensure that the structure to which you are attaching the unit is secure and is able to support a weight of 10 times the unit’s weight. Also, always use a safety cable that can hold 12 times the weight of the unit when installing the xture. The equipment must be installed by a professional, and it must be installed in a place where it is out of the reach of people’s grasp.
ADJ Products, LLC - www.adj.com - Encore Prole 1000 WW User Manual Page 3ADJ Products, LLC - www.adj.com - Encore Prole 1000 WW User Manual Page 2
Page 3
Encore Profile 1000 WW Safety Precautions
Encore Profile 1000 WW DMX Set Up
• To reduce the risk of electrical shock or re, do not expose this unit rain or moisture
• Do not spill water or other liquids into or on to your unit.
• Do not attempt to operate this unit if the power cord has been frayed or broken. Do not attempt to remove or break o the ground prong from the electrical cord. This prong is used to reduce the risk of electrical shock and re in case of an internal short.
• Disconnect from main power before making any type of connection.
• Do not remove the cover under any conditions. There are no user serviceable parts inside.
• Never operate this unit when it’s cover is removed.
• Never plug this unit in to a dimmer pack
• Always be sure to mount this unit in an area that will allow proper ventilation. Allow about 6” (15cm) between this device and a wall.
• Do not attempt to operate this unit, if it becomes damaged.
• This unit is intended for indoor use only, use of this product out` doors voids all warranties.
• During long periods of non-use, disconnect the unit’s main power.
• Always mount this unit in safe and stable matter.
• Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to the point they exit from the unit.
• Cleaning -The fixture should be cleaned only as recommended by t he manufacturer. See page 17 for cleaning details.
• Heat -The appliance should be situated away from heat sources such as radiators, heat registers, stoves, or other appliances (inclu­ d ing amplifiers) that produce heat.
• The fixture should be serviced by qualified service personnel when: A. The power-supply cord or the plug has been damaged. B. Objects have fallen, or liquid has been spilled into the appliance. C. The appliance has been exposed to rain or water. D. The appliance does not appear to operate normally or exhibits a marked change in performance.
Power Supply: The ADJ Encore Prole 1000 WW contains a auto-
matic voltage switch, which will auto sense the voltage when it is plugged into the power source. With this switch there is no need to worry about the correct power voltage, this unit can be plugged in anywhere.
DMX-512: DMX is short for Digital Multiplex. This is a universal pro-
tocol used as a form of communication between intelligent fixtures and controllers. A DMX controller sends DMX data instructions from the controller to the fixture. DMX data is sent as serial data that trav­els from fixture to fixture via the DATA “IN” and DATA “OUT” XLR ter­minals located on all DMX fixtures (most controllers only have a DATA “OUT” terminal).
DMX Linking: DMX is a language allowing all makes and models of dierent manufactures to be linked together and operate from a single controller, as long as all xtures and the controller are DMX compli­ant. To ensure proper DMX data transmission, when using several DMX fixtures try to use the shortest cable path possible. The order in which fixtures are connected in a DMX line does not influence the DMX addressing. For example; a fixture assigned a DMX address of 1 may be placed anywhere in a DMX line, at the beginning, at the end, or anywhere in the middle. When a fixture is assigned a DMX address of 1, the DMX controller knows to send DATA assigned to address 1 to that unit, no matter where it is located in the DMX chain.
Data Cable (DMX Cable) Requirements (For DMX Operation):
The Encore Prole 1000 WW can be controlled via DMX-512 protocol. The Encore Prole 1000 WW has 3 DMX modes, please see pages 7-8 for the dierent modes. The DMX address is set on the back panel of the Encore Prole 1000 WW. Your unit and your DMX controller require a standard 3-pin or 5-pin XLR connector for data input and data output (Figure
1). We recommend Accu-Cable DMX cables. If you are making your own cables, be sure to use standard 110-120 Ohm shielded cable (This cable may be purchased at almost all pro light­ing stores). Your cables should be made with a male and female XLR connector on either end of the cable. Also remember that DMX cable must be daisy chained and
Figure 1
ADJ Products, LLC - www.adj.com - Encore Prole 1000 WW User Manual Page 4
ADJ Products, LLC - www.adj.com - Encore Prole 1000 WW User Manual Page 5
Page 4
Encore Profile 1000 WW DMX Set Up
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
DMX512
DMX+,DMX-,COMMON
1
2
3
Termination reduces signal errors and avoids signal transmission problems and interference. It is always advisable to connect a DMX terminal, (Resistance 120 Ohm 1/4 W) between PIN 2 (DMX-) and PIN 3 (DMX +) of the last fixture.
POWER
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
and PIN 3 (DMX +) of the last fixture.
Encore Profile 1000 WW Operating Instructions
cannot be split.
Notice: Be sure to follow gures two and three when making your own
cables. Do not use the ground lug on the XLR connector. Do not con­nect the cable’s shield conductor to the ground lug or allow the shield conductor to come in contact with the XLR’s outer casing. Grounding the shield could cause a short circuit and erratic behavior.
COMMON
1
DMX512 IN
3
3-PIN XLR
2
Figure 2
XLR Pin Conguration
1 Ground
3 Hot
Pin 1 = Ground
Pin 2 = Data Compliment (negative)
Pin 3 = Data True (positive)
When longer runs of cable are
Figure 4
Pin 1
Pin 2
Pin 3
Do Not Use
Do Not Use
XLR Male Socket
1 Ground
DMX512 OT
3-PIN XLR
2 Cold
3 Hot
1
3
2
DMX +
DMX -
XLR Female Socket
2 Cold
Figure 3
Special Note: Line Termination.
used, you may need to use a terminator on the last unit to avoid erratic behavior. A terminator is a 110-120 ohm 1/4 watt resistor which is con­nected between pins 2 and 3 of a male XLR connector (DATA + and DATA -). This unit is inserted in the female XLR connector of the last unit in your daisy chain to terminate the line. Using a cable terminator (ADJ part number Z-DMX/T) will decrease the possibilities of erratic behavior.
5-Pin XLR DMX Connectors.
512 data cables for DATA transmission in place of 3-pin. 5-pin DMX xtures may be implemented in a 3-pin DMX line. When inserting stan­dard 5-pin data cables in to a 3-pin line a cable adaptor must be used, these adaptors are readily available at most electric stores. The chart below details a proper cable conversion.
Conductor 5-Pin XLR Male (In)3-Pin XLR Female (Out)
Ground/Shield
Data Compliment (- signal)
Data True (+ signal)
Not Used
Not Used
ADJ Products, LLC - www.adj.com - Encore Prole 1000 WW User Manual Page 6
Termination reduces signal errors and
1
avoids signal transmission problems
3
and interference. It is always advisable
2
to connect a DMX terminal, (Resistance 120 Ohm 1/4 W) between PIN 2 (DMX-)
Some manufactures use 5-pin DMX-
3-Pin XLR to 5-Pin XLR Conversion
Pin 1
Pin 2
Pin 3
LCD Backlight On/Off:
To set the LCD backlight to turn off after 20 seconds, press the MODE button until “OTHER” is displayed, press the SET UP button until “OTHER BLGT:XX” is displayed. “XX” represents the current state. Press the UP or DOWN buttons to set the backlight to turn “OFF” after 20 seconds or “ON” to stay on at all times.
Operating Modes:
The Encore Profile 1000 WW has three operating modes:
• Dimmer Mode - Adjust the intensity of the white color.
• Fade Mode - The unit will fade in and out.
• DMX control mode - This function will allow you to control each individual fixtures traits with a standard DMX 512 controller.
Dimmer Mode:
1. Plug the fixture in and press the MODE button until “MANUAL WHIT:XXX” is displayed.
2. Press the UP and DOWN buttons to adjust intensity.
3. After you have adjusted the output intensity you can then activate strobing by pressing the SET UP button to enter strobing.
4. “STRO” will be displayed, this is strobing mode. The strobing can be adjusted between “00” (strobing off) to “15” (fastest strobing).
DMX Mode:
Operating through a DMX controller gives the user the freedom to create their own programs tailored to their own individual needs. The
Encore Profile 1000 WW has 3 DMX modes: 1 channel mode, 2 chan­nel mode, and 3 channel mode. See page 15 for each mode’s DMX
traits.
1. This function will allow you to control each individual fixture’s traits with a standard DMX 512 controller.
2. To run your fixture in DMX mode press the MODE button until “DMX MODE ADDR:XXX” is displayed. “XXX” represents the cur rent displayed DMX address. Use the UP or DOWN buttons to select your desired DMX address, then press the SETUP button to select your DMX Channel mode.
3. Use the UP or DOWN buttons to scroll through the DMX Channel modes. The Channel modes are listed below:
• “CHAN: 01” is 1 Channel DMX Mode.
ADJ Products, LLC - www.adj.com - Encore Prole 1000 WW User Manual Page 7
Page 5
Encore Profile 1000 WW Operating Instructions
Encore Profile 1000 WW Operating Instructions
• “CHAN: 02” is 2 Channel DMX Mode.
• “CHAN: 03” is 3 Channel DMX Mode.
4. Please see page 15 for DMX values and traits.
5. After you have chosen your desired DMX Channel mode plug in the fixture via the XLR connections to any standard DMX control-
ler.
Fade Mode:
1. Plug the fixture in and press the MODE button until “FADE RUN SPEED:XX” is displayed. “XX” represents a number between 01-16.
2. Use the UP and DOWN buttons to find your desired color fade
mode.
3. Press the SET UP button and “SPEED:XX” will be displayed. Use the UP and DOWN buttons to adjust the speed of the color
fade.
System Reset:
This will return the fixture to its factory settings.
1. Plug the fixture in and press the MODE button until “OTHER MODE” is displayed.
2. Press the SET UP button until “SYSRESET” is displayed.
3. Press the UP and DOWN buttons simultaneously to reset or press the MODE button to exit.
Dimmer Curve:
This is used to set the dimming curve used with DMX mode. See page 29 for the different dimming curves.
1. Plug the fixture in and press the MODE button until “DMX MODE ADDR:XXX” is displayed.
2. Press the SET UP button until “DELAY:X” is displayed. “X” repre-
sents the displayed dimmer curve (0-4).
• 0 - Standard
• 1 - Stage
• 2 - TV
• 3 - Architectural
• 4 - Theatre
3. Press the UP or DOWN buttons to scroll through and select
your desired dimming curve.
DMX State:
This mode can be used as a precaution mode, that in case the DMX signal is lost, the operating mode chosen in the setup is the running mode the xture will go into when the DMX signal is lost. You can also set this as the operating mode you would like the unit to return to when power is applied.
1. Plug the fixture in and press the MODE button until “DMX MODE ADDR:XXX” is displayed.
2. Press the SET UP button until “DMX MODE NO” is displayed. The
current DMX state will be displayed.
• “BLACK” (Blackout) - If the DMX signal is lost or interrupted,
the unit will automatically go into stand by mode.
• “HOLD” (Last State) - If the DMX signal is lost or interrupted,
the xture will stay in the last DMX set up.
• “AUTO” (Auto Run) - If the DMX signal is lost or interrupted,
the unit will automatically go into Auto Run mode.
3. Press the UP or DOWN buttons to scroll through and select
your desired DMX state.
IR Receiver On/Off:
This function is used to activate and deactivate the infared sensor. When this function is activated you can control the fixture using the ADJ LED RC2 (sold separately), ADJ UC IR (sold separately), and Airstream IR app. Please see pages 12-14 for remote controls and functions. To control the Encore Profile 1000 WW, plug the included IR receiver into IR receiver input located on the rear of the controller. You must aim the remote at the IR sensor and be no more the 30 feet away.
1. Plug the fixture in and press the MODE button until “OTHER
MODE” is displayed.
2. Press the SET UP button until “IR: XX” is displayed.
3. Press the UP or DOWN buttons to either activate the remote func-
tion (On) or deactivate it (Off).
Gamma:
This feature is predominately used when shooting video. Adjust the gamma setting to clean up any lines that might be seen on camera.
1. Plug the fixture in and press the MODE button until “GAMMA” is
ADJ Products, LLC - www.adj.com - Encore Prole 1000 WW User Manual Page 9ADJ Products, LLC - www.adj.com - Encore Prole 1000 WW User Manual Page 8
Page 6
Encore Profile 1000 WW Operating Instructions
Encore Profile 1000 WW Master-Slave Configuration
displayed. The current gamma setting will be displayed.
2. Use the UP and DOWN buttons to switch the gamma setting.
Fan Speed:
This will let you set your desired fan speed.
1. Plug the fixture in and press the MODE button until “FAN SPEED” is displayed, and press ENTER.
2. Use the UP and DOWN buttons to switch between the different
fan speeds.
Refresh Rate:
This feature is predominately used when shooting video. Adjust the frequency setting to clear up any LED flicker that might be seen on
camera.
1. Plug the fixture in and press the MODE button until “FREQUENC” is displayed. The current frequency setting will be displayed.
2. Use the UP and DOWN buttons to switch the frequency setting.
PCB Temperature:
This will check the current temperature of unit as well as switch between fahrenheit and celsius.
1. Plug the fixture in and press the MODE button until “OTHER MODE” is displayed.
2. Press the SET UP button until “TEM:XXXX” is displayed.
3. Use the UP and DOWN buttons to switch between fahrenheit and celsius.
Master-Slave Configuration:
This function will allows you to link units together to run in a Master­Slave setup. In a Master-Slave set up one unit will act as the control-
ling unit and the others will react to the controlling units built-in pro­grams. Any unit can act as a Master or as a Slave however, only one
unit can be programmed to act as the “Master.”
Master-Slave Connections and Settings:
1. Daisy chain your units via the XLR connector on the rear of the
unit. Use standard XLR data cables to link your units together. Remember that the Male XLR connector is the input and the Female XLR connector is the ouput. The first unit in the chain (master) will use the female XLR connector only. The last unit in the chain will use the male XLR connector only.
2. Set the “Master” unit to your desired mode of operation.
3. On the “Slave” units press the MODE button until “Slave Mode” is
displayed. The unit is now set as the “Slave” unit. Each slave unit must be set to the same setting.
4. Connect the rst “Slave” unit to the “Master”, and the “Slave” unit
should now start to follow the “Master”.
Encore Profile 1000 WW Gobo Install
The Encore Profile 1000 WW comes with 4 replaceable gobos (see below). To install a gobo, unscrew and remove the phillips screw located at the bottom of the gobo holder. Gently lift part of the gobo holder side up and carefully slide the gobo into place. Reinstall the phil­lips and screw and tighten. Slide the gobo holder into the slot located at the top of the unit in front of the framing lever.
Encore Profile 1000 WW Focus and Zoom Adjustments
The knobs located on the right side of unit are used to adjust the focus and the zoom. For a tighter/narrow beam move the first/front knob to the front of the fixture, and move the second knob to rear. For a wider beam, move the first/front knob towards the middle of the fixture, and move the second knob towards the middle as well. Adjust accordingly.
ADJ Products, LLC - www.adj.com - Encore Prole 1000 WW User Manual Page 10 ADJ Products, LLC - www.adj.com - Encore Prole 1000 WW User Manual Page 11
Page 7
Encore Profile 1000 WW ADJ LED RC2 Operation
Encore Profile 1000 WW ADJ LED RC2 Operation
The ADJ LED RC2 infrared remote (sold seperately) has many dif­fernet functions to control your Encore Profile 1000 WW. To control the fixture you must aim the controller at the infrared sensor and be no more the 30 feet away. To use the ADJ LED RC2 you must first activate the fixtures infrared sensor, to activate the sensor please see the instructions on page 9.
BLACKOUT - Pressing this button will blackout the fixture.
SELECT PROG - Pressing this button will activate fade mode. Press
the “+” or “-” buttons to adjust the running speed.
FLASH - This button will activate the strobe effect. You can control the flash rate by pressing the “+” and “-” buttons. Press the White button again to exit strobing mode.
SPEED - This button is invalid for this fixture.
DMX MODE - This button will cycle between DMX addressing, DMX
channel mode, and dimmer curve selection. Some fixtures will come with different DMX channel modes. This button will switch between the different modes. Please see pages 16-22 for DMX modes, values,
and traits.
SLAVE/SOUND ACTIVE - This designates the fixture as a slave fix­ture in a master/slave configuration. Sound activity is invalid for this fixture.
SET ADDRESS - Press this button to set the DMX address. Press this button first, then press the numbers to set the address. If the ad­dress is correctly set, the LED will flash and the unit will automatically go into DMX mode.
Example: Set DMX Address 1 Press “S-0-0-1” Set DMX Address 245 Press “S-2-4-5”
DMX Mode:
Operating through a DMX controller gives the user the freedom to create their own programs tailored to their own individual needs.
Follow the directions below to set your DMX address, DMX channel mode, and dimmer curve mode.
1. Before connecting to a DMX controller, your fixture has different
DMX channel modes, please select your desired mode by press­ ing the DMX Mode button, and use the “+” or “-” buttons to scroll through the DMX channel modes. Set the mode before you address the fixture. See the bottom of this page for the different DMX modes.
2. Press this button again to enter dimmer curve selection and use
the “+” or “-” buttons to scroll through the dimmer curve modes.
3. After you have selected your mode, set the DMX address for the
fixture by pressing the “S” button. When the “S” button is pressed the LED’s will flash 2-3 times. Use the number buttons to press in your desired address. See “SET ADDRESS” on page 12 for examples. Note: When seeting the DMX address each time a number is pressed a LED color will flash, when you have set the DMX address correctly all LED’s will flash 2-3 times.
4. Now you may connect the fixture via the XLR connections to any
standard DMX controller. Please see page 12 to for a detailed descriptions of the DMX modes, values, and traits.
• If the White LED flashes 1 time you are in 1 Channel Mode.
• If the White LED flashes 2 times you are in 2 Channel Mode.
• If the White LED flashes 3 times you are in 3 Channel Mode.
R G B W - Buttons R G B are invalide for this fixture. Press White but­ton and the use the “+” or “-” to adjust the output intensity. Press the FLASH button to activate strobing and use the “+” or “-” to adjust the
flash speed.
“+” and “-” - These buttons adjust the flash rate, speed of the fade mode, and output intensity.
ADJ Products, LLC - www.adj.com - Encore Prole 1000 WW User Manual Page 12 ADJ Products, LLC - www.adj.com - Encore Prole 1000 WW User Manual Page 13
Page 8
Encore Profile 1000 WW UC IR & Airstream IR Functions
Encore Profile 1000 WW 1 Channel Mode
The UC IR (sold separately) infrared remote gives you control of various functions (See below). To control the fixture you must aim the remote at the front of the fixture and be no more than 30 feet away.
The Encore Profile 1000 WW is also compatible with the Airstream IR app. The IR transmitter is available through any ADJ dealer or through the ADJ parts website. The transmitter plugs into the head­phone jack of your iOS phone or tablet. To control your IR fixture you must raise the volume to the maximum on your iOS phone or table and aim the transmitter at the front of the fixture and be no more than 15 feet away. After you have purchased the Airstream IR transmitters, the app is a free download from the app store for your iOS phone or tablet. The app comes with 3 pages of control depending on the IR fixture you are using. Please see below for IR functions including the corresponding app page. To use either of these means of control you must first activate the fixtures infrared sensor. To activate the sensor please see the instructions on page 9.
Works with App page 1.
STAND BY - Pressing this button will blackout the fixture. Press the
button again to return to the initial state.
FULL ON - Hold this button down to fully light up the unit. When you let the button go, the unit will return to its previous state.
FADE/GOBO - Press this button activate fade mode.
Channel Value Function
1 WHITE
0 - 255 0% - 100%
Encore Profile 1000 WW 2 Channel Mode
Channel Value Function
1 WHITE
0 - 255 0% - 100% 2 MASTER DIMMER 0 - 255 0% - 100%
Encore Profile 1000 WW 3 Channel Mode
Channel Value Function
1 WHITE
0 - 255 0% - 100% 2 MASTER DIMMER 0 - 255 0% - 100% 3 STROBING 0 - 15 NO FUNCTION 16 - 255 STROBING SLOW - FAST
“DIMMER +” and “DIMMER -” - Use these buttons to output inten-
Encore Profile 1000 WW CAD Drawing
sity when in dimmer mode.
STROBE - Press this button for strobing.
188.6mm/7.425”
557.3mm/21.94”
COLOR - Press this button to activate dimmer mode. Use the “DIMMER+” and “DIMMER-” to scroll through the colors.
1-9 - These buttons are invalid for this fixture
173.6mm/6.834”
SHOW 0 - This button is not valid for this fixture.
ADJ Products, LLC - www.adj.com - Encore Prole 1000 WW User Manual Page 14 ADJ Products, LLC - www.adj.com - Encore Prole 1000 WW User Manual Page 15
373.49mm/14.70”
264.02mm/10.394”
Page 9
Encore Profile 1000 WW Photometric Chart
Encore Profile 1000 WW Power Cord Daisy Chain
With this feature you can connect the xtures to one another
using the PowerCON input and output sockets. The quantity that
can be connected is 5 xtures maximum. After 5 xtures you will need to use a new power outlet. They must be the same xtures. DO NOT mix xtures.
Encore Profile 1000 WW Fuse Replacement
Disconnect the unit from its power source. Remove the power cord from the unit. Once the cord has been removed, the fuse holder is located above the powerCON connection. Use a phillips head screw­driver to remove the fuse holder. Remove the fuse located inside the fuse holder and replace with the new fuse. Install the fuse holder and new fuse and secure it.
Encore Profile 1000 WW Trouble Shooting
Encore Profile 1000 WW Dimmer Curve Chart
Ramp Effect
Standard
Stage
TV
Architectural
Theatre
(Fade Time) (Fade Time)
Listed below are a few common problems the user may encounter, with solutions.
Unit not responding to DMX:
1. Check that the DMX cables are connected properly and are
wired correctly (pin 3 is “hot”; on some other DMX devices pin 2 may be ‘hot’). Also, check that all cables are connected to the right connectors; it does matter which way the inputs and outputs are connected.
Encore Profile 1000 WW Cleaning
Due to fog residue, smoke, and dust cleaning the internal and exter­nal optical lenses must be carried out periodically to optimize light output.
1. Use normal glass cleaner and a soft cloth to wipe down the
outside casing.
2. Clean the external optics with glass cleaner and a soft cloth
every 20 days.
3. Always be sure to dry all parts completely before plugging
the unit back in. Cleaning frequency depends on the environment in which the fixture operates (i.e. smoke, fog residue, dust, dew).
ADJ Products, LLC - www.adj.com - Encore Prole 1000 WW User Manual Page 16 ADJ Products, LLC - www.adj.com - Encore Prole 1000 WW User Manual Page 17
Page 10
Encore Profile 1000 WW Warranty
MANUFACTURER’S LIMITED WARRANTY
A. ADJ Products, LLC hereby warrants, to the original purchaser, ADJ Products, LLC products to be free of manufacturing defects in material and workmanship for a prescribed period from the date of purchase (see specific warranty period on reverse). This warranty shall be valid only if the product is purchased within the United States of America, including possessions and territories. It is the owner’s responsibility to establish the date and place of purchase by acceptable evidence, at the time service is sought.
B. For warranty service you must obtain a Return Authorization number (RA#) before sending back the product–please contact ADJ Products, LLC Service Department at 800-322-6337. Send the product only to the ADJ Products, LLC factory. All shipping charges must be pre-paid. If the requested repairs or service (including parts replacement) are within the terms of this warranty, ADJ Products, LLC will pay return shipping charges only to a designated point within the United States. If the entire instrument is sent, it must be shipped in it’s original package. No accessories should be shipped with the product. If any accessories are shipped with the product, ADJ Products, LLC shall have no liability whatsoever for loss of or damage to any such accessories, nor for the safe return thereof.
C. This warranty is void if the serial number has been altered or removed; if the product is modified in any manner which ADJ Products, LLC concludes, after inspection, affects the reliability of the product; if the product has been repaired or serviced by anyone other than the ADJ Products, LLC factory unless prior written authorization was issued to purchaser by ADJ Products, LLC; if the product is damaged because not properly maintained as set forth in the instruction manual.
D. This is not a service contract, and this warranty does not include maintnance, cleaning or periodic check up. During the period specified above, ADJ Products, LLC will replace defective parts at its expense with new or refurbished parts, and will absorb all expenses for warranty service and repair labor by reason of defects in material or workmanship. The sole responsibility of ADJ Products, LLC under this warranty shall be limited to the repair of the product, or replacement thereof, including parts, at the sole discretion of ADJ Products, LLC. All products covered by this warranty were manufactured after August 15, 2012, and bear indentifying marks to that effect.
E. ADJ Products, LLC reserves the right to make changes in design and/or improvements upon its products without any obligation to include these changes in any products theretofore manufactured.
No warranty, whether expressed or implied, is given or made with respect to any accessory supplied with products described above. Except to the extent prohibited by applicable law, all implied warranties made by ADJ Products, LLC in connection with this product, including warranties of merchantability or fitness, are limited in duration to the warranty period set forth above. And no warranties, whether expressed or implied, including warranties of merchantability or fitness, shall apply to this product after said period has expired. The consumer’s and/or Dealer’s sole remedy shall be such repair or replacement as is expressly provided above; and under no circumstances shall ADJ Products, LLC be liable for any loss or damage, direct or consequential, arising out of the use of, or inability to use, this product.
This warranty is the only written warranty applicable to ADJ Products, LLC Products and supersedes all prior warranties and written descriptions of warranty terms and conditions heretofore published.
MANUFACTURER’S LIMITED WARRANTY PERIODS:
•LightingProducts=1-year(365days)LimitedWarranty(Such as: Special Effect Lighting, Intelligent
Lighting, UV lighting, Strobes, Fog Machines, Bubble Machines, Mirror Balls, Par Cans, Trussing, Lighting Stands etc. excluding LED and lamps)
•LaserProducts=1Year(365Days)LimitedWarranty(excluding laser diodes which have a 6 month
limited warranty)
•L.E.D.Products=2-year(730days)LimitedWarranty(excluding motors, PCB boards, and power supplies, which have a 1-year (365 day Limited Warranty) batteries which have a 180 day limited war-
ranty). Only the L.E.D.s carry a 2-year warranty (excludingStarTecSerieswhichacarriesa1Year
LimitedWarranty)Note:2YearWarrantyonlyappliestopurchaseswithintheUnitedStates.
•ADJDMXControllers=2Year(730Days)LimitedWarranty(excluding faders and tact switches)
ADJ Products, LLC - www.adj.com - Encore Prole 1000 WW User Manual Page 18
Encore Profile 1000 WW Specifications
Model:
Encore Profile 1000 WW
Voltage: 100V ~ 240V/50~60Hz LEDs: 1 x 120W WW COB LED (3200K, CRI 98) Beam Angle: 12-30 Degrees Working Position: Any safe working position Power Draw: 144W Power Cord Daisy Chain: 5 Fixtures Max. Fuse: 3 Amp Weight: 19 lbs./ 8.5Kgs. Dimensions: 22” (L) x 9.75” (W) x 15.25” (H) 560 x 250 x 385mm Colors: Warm White DMX Channels: 3 DMX Modes: 1 Channel Mode, 2 Channel Mode, & 3 Channel Mode Warranty: 2 Year (730 days)
Auto Sensing Voltage: This xture contains a automatic volt-
age switch, which will auto sense the voltage when it is plugged into the power source.
Please Note: Specications and improvements in the design of this unit and this manual are subject to change without any prior written notice.
ADJ Products, LLC
6122 S. Eastern Ave. Los Angeles, CA 90040 USA
Tel: 323-582-2650 / Fax: 323-725-6100
Web: www.adj.com / E-mail: info@americandj.com
A.D.J. Supply Europe B.V.
Junostraat 2
6468 EW Kerkrade
The Netherlands
service@adjgroup.eu / www.adj.eu
Tel: +31 45 546 85 00 / Fax: +31 45 546 85 99
Loading...