Page 1
ADJ Products, LLC
6122 S. Eastern Ave. Los Angeles, CA 90040 USA
Tel: 323-582-2650 / Fax: 323-725-6100
Web: www.adj.com / E-mail: info@americandj.com
EncorE ProfilE 1000 color
A.D.J. Supply Europe B.V.
Junostraat 2
6468 EW Kerkrade
The Netherlands
service@adjgroup.eu / www.adj.eu
Tel: +31 45 546 85 00 / Fax: +31 45 546 85 99
User Instructions
3/16
Page 2
©2016 ADJ Products, LLC all rights reserved. Information,
specications, diagrams, images, and instructions herein are
subject to change without notice. ADJ Products, LLC logo and
identifying product names and numbers herein are trademarks
of ADJ Products, LLC. Copyright protection claimed includes all
forms and matters of copyrightable materials and information
now allowed by statutory or judicial law or hereinafter granted.
Product names used in this document may be trademarks or
registered trademarks of their respective companies and are
hereby acknowledged. All non-ADJ Products, LLC brands and
product names are trademarks or registered trademarks of their
respective companies.
ADJ Products, LLC and all aliated companies hereby dis-
claim any and all liabilities for property, equipment, building, and
electrical damages, injuries to any persons, and direct or indirect economic loss associated with the use or reliance of any
information contained within this document, and/or as a result
of the improper, unsafe, unsucient and negligent assembly,
installation, rigging, and operation of this product.
Encore Profile 1000 Color Specifications
Model:
Encore Profile 1000 Color
Voltage: 100V ~ 240V/50~60Hz
LEDs: 1 x 120W RGBw 4-in-1 COB LED
Beam Angle: 12-30 Degrees
Working Position: Any safe working position
Power Draw: 144W
Power Cord Daisy Chain: 5 Fixtures Max.
Fuse: 3 Amp
Weight: 19 lbs./ 8.5Kgs.
Dimensions: 22” (L) x 9.75” (W) x 15.25” (H)
560 x 250 x 385mm
Colors: RGBW Mixing
Gobo Size: Outer Diameter: 61mm
Inner Diameter: 51mm
Thickness: 2mm
DMX Channels: 5 DMX Modes: 4 Channel Mode,
5 Channel Mode, 6 Channel Mode,
10 Channel Mode, & 11 Channel
Mode
Warranty: 2 Year (730 days)
Europe Energy Saving Notice
Energy Saving Matters (EuP 2009/125/EC)
Saving electric energy is a key to help protecting the enviroment.
Please turn o all electrical products when they are not in use. To
avoid power consumption in idle mode, disconnect all electrical
equipment from power when not in use. Thank you!
Auto Sensing Voltage: This xture contains a automatic volt-
age switch, which will auto sense the voltage when it is plugged
into the power source.
Please Note: Specications and improvements in the design of
this unit and this manual are subject to change without any prior
written notice.
ADJ Products, LLC - www.adj.com - Encore Prole 1000 Color User Manual Page 30
Page 3
Encore Profile 1000 Color Notes
Encore Profile 1000 Color Introduction
Unpacking:
Thank you for purchasing the Encore Prole 1000 Color
by ADJ Products, LLC. Every Encore Prole 1000 Color has been
thoroughly tested and has been shipped in perfect operating condition. Carefully check the shipping carton for damage that may have
occurred during shipping. If the carton appears to be damaged, care-
fully inspect your xture for any damage and be sure all accessories
necessary to operate the unit has arrived intact. In the case damage
has been found or parts are missing, please contact our toll free customer support number for further instructions. Do not return this unit to
your dealer without rst contacting customer support.
Introduction:
The ADJ Encore Profile 1000 Color is a DMX intelligent,
high powered LED follow spot. This follow spot has five operating
modes: RGBW dimmer mode, color change mode, color fade mode,
auto run mode, static color mode, and DMX control mode. This xture
can be used in a stand alone mode or connected in a Master/Slave
conguration. To optimize the performance of this product, please
read these operating instructions carefully to familiarize yourself with
the basic operations of this unit. These instructions contain important safety information regarding the use and maintenance of this unit.
Please keep this manual with the unit, for future reference.
Customer Support: ADJ Products, LLC provides a customer support
line, to provide set up help and to answer any question should you
encounter problems during your set up or initial operation. You may
also visit us on the web at www.adj.com for any comments or suggestions. Service Hours are Monday through Friday 8:00 a.m. to 4:30 p.m.
Pacic Standard Time.
Voice: (323) 582-3322
Fax: (323) 582-3108
E-mail: support@AmericanDJ.com
ADJ Products, LLC - www.adj.com - Encore Prole 1000 Color User Manual Page 29
Warning! To prevent or reduce the risk of electrical shock or re, do
not expose this unit to rain or moisture.
Caution! There are no user serviceable parts inside this unit. Do not
attempt any repairs yourself, doing so will void your manufactures warranty. In the unlikely event your unit may require service please contact
ADJ Products, LLC.
PLEASE recycle the shipping carton when ever possible.
ADJ Products, LLC - www.adj.com - Encore Prole 1000 Color User Manual Page 2
Page 4
Encore Profile 1000 Color Features
• Five Operating Modes
• Electronic Dimming 0-100%
• 5 Selectable Dimming Curves
• 64 Color Macros
• 4 Included Gobos
• DMX-512 protocol
• 3-Pin & 5-Pin DMX Connections
• 5 DMX Modes: 4 Channel Mode, 5 Channel Mode, 6 Channel
Mode, 10 Channel Mode, & 11 Channel Mode.
• ADJ LED RC2, ADJ UC IR, (Not Included) & Airstream IR compat-
ible
• Power Cord Daisy Chain (See page 26)
Encore Profile 1000 Color Warranty Registration
The Encore Profile 1000 Color carries a 2 year limited warranty.
Please fill out the enclosed warranty card to validate your purchase.
All returned service items whether under warranty or not, must be
freight pre-paid and accompany a return authorization (R.A.) number.
The R.A. number must be clearly written on the outside of the return
package. A brief description of the problem as well as the R.A. number
must also be written down on a piece of paper included in the shipping carton. If the unit is under warranty, you must provide a copy of
your proof of purchase invoice. You may obtain a R.A. number by contacting our customer support team on our customer support number.
All packages returned to the service department not displaying a R.A.
number on the outside of the package will be returned to the shipper.
Encore Profile 1000 Color Notes
Encore Profile 1000 Color Installation
The unit should be mounted using a mounting clamp (not provided),
axing it to the mounting bracket that is provided with the unit.
Always ensure that the unit is rmly xed to avoid vibration and slip-
ping while operating. Always ensure that the structure to which you
are attaching the unit is secure and is able to support a weight of 10
times the unit’s weight. Also, always use a safety cable that can hold
12 times the weight of the unit when installing the xture.
The equipment must be installed by a professional, and it must be
installed in a place where it is out of the reach of people’s grasp.
ADJ Products, LLC - www.adj.com - Encore Prole 1000 Color User Manual Page 3
ADJ Products, LLC - www.adj.com - Encore Prole 1000 Color User Manual Page 28
Page 5
Encore Profile 1000 Color Warranty
MANUFACTURER’S LIMITED WARRANTY
A. ADJ Products, LLC hereby warrants, to the original purchaser, ADJ Products, LLC products
to be free of manufacturing defects in material and workmanship for a prescribed period from
the date of purchase (see specific warranty period on reverse). This warranty shall be valid only if the
product is purchased within the United States of America, including possessions and
territories. It is the owner’s responsibility to establish the date and place of purchase by acceptable
evidence, at the time service is sought.
B. For warranty service you must obtain a Return Authorization number (RA#)
before sending back the product–please contact ADJ Products, LLC Service Department
at 800-322-6337. Send the product only to the ADJ Products, LLC factory. All
shipping charges must be pre-paid. If the requested repairs or service (including
parts replacement) are within the terms of this warranty, ADJ Products, LLC will pay return
shipping charges only to a designated point within the United States. If the entire instrument is
sent, it must be shipped in it’s original package. No accessories should be shipped with the product. If
any accessories are shipped with the product, ADJ Products, LLC shall have no liability whatsoever for
loss of or damage to any such accessories, nor for the safe return thereof.
C. This warranty is void if the serial number has been altered or removed; if the product is modified in any
manner which ADJ Products, LLC concludes, after inspection, affects the reliability of the product; if the
product has been repaired or serviced by anyone other than the ADJ Products, LLC factory unless prior
written authorization was issued to purchaser by ADJ Products, LLC; if the product is damaged because
not properly maintained as set forth in the instruction manual.
D. This is not a service contract, and this warranty does not include maintnance, cleaning or periodic check
up. During the period specified above, ADJ Products, LLC will replace defective parts at its expense
with new or refurbished parts, and will absorb all expenses for warranty service and repair labor by
reason of defects in material or workmanship. The sole responsibility of ADJ Products, LLC under this
warranty shall be limited to the repair of the product, or replacement thereof, including parts, at the sole
discretion of ADJ Products, LLC. All products covered by this warranty were manufactured after August
15, 2012, and bear indentifying marks to that effect.
E. ADJ Products, LLC reserves the right to make changes in design and/or improvements upon its products
without any obligation to include these changes in any products theretofore manufactured.
No warranty, whether expressed or implied, is given or made with respect to any accessory supplied with
products described above. Except to the extent prohibited by applicable law, all implied warranties made
by ADJ Products, LLC in connection with this product, including warranties of merchantability or fitness,
are limited in duration to the warranty period set forth above. And no warranties, whether expressed or
implied, including warranties of merchantability or fitness, shall apply to this product after said period
has expired. The consumer’s and/or Dealer’s sole remedy shall be such repair or replacement as is
expressly provided above; and under no circumstances shall ADJ Products, LLC be liable for any loss or
damage, direct or consequential, arising out of the use of, or inability to use, this product.
This warranty is the only written warranty applicable to ADJ Products, LLC Products and
supersedes all prior warranties and written descriptions of warranty terms and conditions heretofore
published.
MANUFACTURER’S LIMITED WARRANTY PERIODS:
•LightingProducts=1-year(365days)LimitedWarranty(Such as: Special Effect Lighting, Intelligent
Lighting, UV lighting, Strobes, Fog Machines, Bubble Machines, Mirror Balls, Par Cans, Trussing,
Lighting Stands etc. excluding LED and lamps)
•LaserProducts=1Year(365Days)LimitedWarranty(excluding laser diodes which have a 6 month
limited warranty)
•L.E.D.Products=2-year(730days)LimitedWarranty(excluding motors, PCB boards, and power
supplies, which have a 1-year (365 day Limited Warranty) batteries which have a 180 day limited war-
ranty). Only the L.E.D.s carry a 2-year warranty (excludingStarTecSerieswhichacarriesa1Year
LimitedWarranty)Note:2YearWarrantyonlyappliestopurchaseswithintheUnitedStates.
•ADJDMXControllers=2Year(730Days)LimitedWarranty(excluding faders and tact switches)
ADJ Products, LLC - www.adj.com - Encore Prole 1000 Color User Manual Page 27
Encore Profile 1000 Color Safety Precautions
• To reduce the risk of electrical shock or re, do not expose this unit
rain or moisture
• Do not spill water or other liquids into or on to your unit.
• Do not attempt to operate this unit if the power cord has been
frayed or broken. Do not attempt to remove or break o the ground
prong from the electrical cord. This prong is used to reduce the risk
of electrical shock and re in case of an internal short.
• Disconnect from main power before making any type of connection.
• Do not remove the cover under any conditions. There are no user
serviceable parts inside.
• Never operate this unit when it’s cover is removed.
• Never plug this unit in to a dimmer pack
• Always be sure to mount this unit in an area that will allow proper
ventilation. Allow about 6” (15cm) between this device and a wall.
• Do not attempt to operate this unit, if it becomes damaged.
• This unit is intended for indoor use only, use of this product out`
doors voids all warranties.
• During long periods of non-use, disconnect the unit’s main power.
• Always mount this unit in safe and stable matter.
• Power-supply cords should be routed so that they are not likely to
be walked on or pinched by items placed upon or against them,
paying particular attention to the point they exit from the unit.
• Cleaning -The fixture should be cleaned only as recommended by
t he manufacturer. See page 26 for cleaning details.
• Heat -The appliance should be situated away from heat sources
such as radiators, heat registers, stoves, or other appliances (inclu d ing amplifiers) that produce heat.
• The fixture should be serviced by qualified service personnel when:
A. The power-supply cord or the plug has been damaged.
B. Objects have fallen, or liquid has been spilled into the appliance.
C. The appliance has been exposed to rain or water.
D. The appliance does not appear to operate normally or exhibits a
marked change in performance.
ADJ Products, LLC - www.adj.com - Encore Prole 1000 Color User Manual Page 4
Page 6
Encore Profile 1000 Color DMX Set Up
Encore Profile 1000 Color Power Cord Daisy Chain
Power Supply: The ADJ Encore Prole 1000 Color contains a auto-
matic voltage switch, which will auto sense the voltage when it is
plugged into the power source. With this switch there is no need to
worry about the correct power voltage, this unit can be plugged in
anywhere.
DMX-512: DMX is short for Digital Multiplex. This is a universal pro-
tocol used as a form of communication between intelligent fixtures
and controllers. A DMX controller sends DMX data instructions from
the controller to the fixture. DMX data is sent as serial data that travels from fixture to fixture via the DATA “IN” and DATA “OUT” XLR terminals located on all DMX fixtures (most controllers only have a DATA
“OUT” terminal).
DMX Linking: DMX is a language allowing all makes and models of
dierent manufactures to be linked together and operate from a single
controller, as long as all xtures and the controller are DMX compli-
ant. To ensure proper DMX data transmission, when using several
DMX fixtures try to use the shortest cable path possible. The order
in which fixtures are connected in a DMX line does not influence the
DMX addressing. For example; a fixture assigned a DMX address of 1
may be placed anywhere in a DMX line, at the beginning, at the end,
or anywhere in the middle. When a fixture is assigned a DMX address
of 1, the DMX controller knows to send DATA assigned to address 1
to that unit, no matter where it is located in the DMX chain.
Data Cable (DMX Cable) Requirements (For DMX Operation):
The Encore Prole 1000 Color can be controlled via DMX-512 protocol.
The Encore Prole 1000 Color has 5 DMX modes, please see pages 9-10
for the dierent modes. The DMX address is set on the back panel of the
Encore Prole 1000 Color. Your unit and your DMX
controller require a standard 3-pin or 5-pin XLR
connector for data input and data output (Figure
1). We recommend Accu-Cable DMX cables.
If you are making your own cables, be sure to
use standard 110-120 Ohm shielded cable (This
cable may be purchased at almost all pro lighting stores). Your cables should be made with a
male and female XLR connector on either end of
the cable. Also remember that DMX cable must be daisy chained and
Figure 1
With this feature you can connect the xtures to one another
using the PowerCON input and output sockets. The quantity that
can be connected is 5 xtures maximum. After 5 xtures you will
need to use a new power outlet. They must be the same xtures.
DO NOT mix xtures.
Encore Profile 1000 Color Fuse Replacement
Disconnect the unit from its power source. Remove the power cord
from the unit. Once the cord has been removed, the fuse holder is
located above the powerCON connection. Use a phillips head screwdriver to remove the fuse holder. Remove the fuse located inside the
fuse holder and replace with the new fuse. Install the fuse holder and
new fuse and secure it.
Encore Profile 1000 Color Trouble Shooting
Listed below are a few common problems the user may encounter,
with solutions.
Unit not responding to DMX:
1. Check that the DMX cables are connected properly and are
wired correctly (pin 3 is “hot”; on some other DMX devices
pin 2 may be ‘hot’). Also, check that all cables are connected
to the right connectors; it does matter which way the inputs
and outputs are connected.
Encore Profile 1000 Color Cleaning
Due to fog residue, smoke, and dust cleaning the internal and external optical lenses must be carried out periodically to optimize light
output.
1. Use normal glass cleaner and a soft cloth to wipe down the
outside casing.
2. Clean the external optics with glass cleaner and a soft cloth
every 20 days.
3. Always be sure to dry all parts completely before plugging
the unit back in.
Cleaning frequency depends on the environment in which the fixture
operates (i.e. smoke, fog residue, dust, dew).
ADJ Products, LLC - www.adj.com - Encore Prole 1000 Color User Manual Page 5
ADJ Products, LLC - www.adj.com - Encore Prole 1000 Color User Manual Page 26
Page 7
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
DMX512
DMX+,DMX-,COMMON
1
2
3
Termination reduces signal errors and
avoids signal transmission problems
and interference. It is always advisable
to connect a DMX terminal, (Resistance
120 Ohm 1/4 W) between PIN 2 (DMX-)
and PIN 3 (DMX +) of the last fixture.
POWER
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
and PIN 3 (DMX +) of the last fixture.
Encore Profile 1000 Color Gobo Install
Encore Profile 1000 Color DMX Set Up
The Encore Profile 1000 Color comes with 4 replaceable gobos (see
below). To install a gobo, unscrew and remove the phillips screw
located at the bottom of the gobo holder. Gently lift part of the gobo
holder side up and carefully slide the gobo into place. Reinstall the phillips and screw and tighten. Slide the gobo holder into the slot located
at the top of the unit in front of the framing lever.
Encore Profile 1000 Color Dimmer Curve Chart
cannot be split.
Notice: Be sure to follow gures two and three when making your own
cables. Do not use the ground lug on the XLR connector. Do not connect the cable’s shield conductor to the ground lug or allow the shield
conductor to come in contact with the XLR’s outer casing. Grounding
the shield could cause a short circuit and erratic behavior.
COMMON
1
DMX512 IN
3
3-PIN XLR
2
Figure 2
XLR Pin Conguration
1 Ground
3 Hot
Pin 1 = Ground
Pin 2 = Data Compliment (negative)
Pin 3 = Data True (positive)
When longer runs of cable are
Figure 4
XLR Male Socket
1 Ground
DMX512 OT
3-PIN XLR
2 Cold
3 Hot
1
3
2
DMX +
DMX -
XLR Female Socket
2 Cold
Figure 3
Special Note: Line Termination.
used, you may need to use a terminator on the last unit to avoid erratic
behavior. A terminator is a 110-120 ohm 1/4 watt resistor which is connected between pins 2 and 3 of a male XLR connector (DATA + and
DATA -). This unit is inserted in the female XLR connector of the last
unit in your daisy chain to terminate the line. Using a cable terminator
(ADJ part number Z-DMX/T) will decrease the possibilities of erratic
behavior.
Termination reduces signal errors and
1
avoids signal transmission problems
3
and interference. It is always advisable
2
to connect a DMX terminal, (Resistance
120 Ohm 1/4 W) between PIN 2 (DMX-)
Ramp Effect
Standard
Stage
TV
Architectural
Theatre
ADJ Products, LLC - www.adj.com - Encore Prole 1000 Color User Manual Page 25
(Fade Time) (Fade Time)
5-Pin XLR DMX Connectors.
Some manufactures use 5-pin DMX-
512 data cables for DATA transmission in place of 3-pin. 5-pin DMX
xtures may be implemented in a 3-pin DMX line. When inserting standard 5-pin data cables in to a 3-pin line a cable adaptor must be used,
these adaptors are readily available at most electric stores. The chart
below details a proper cable conversion.
3-Pin XLR to 5-Pin XLR Conversion
Conductor 5-Pin XLR Male (In)3-Pin XLR Female (Out)
Ground/Shield
Data Compliment (- signal)
Data True (+ signal)
Not Used
Not Used
Pin 1
Pin 2
Pin 3
ADJ Products, LLC - www.adj.com - Encore Prole 1000 Color User Manual Page 6
Pin 1
Pin 2
Pin 3
Do Not Use
Do Not Use
Page 8
Encore Profile 1000 Color Operating Instructions
LCD Backlight On/Off:
To set the LCD backlight to turn off after 20 seconds, press the
MODE button until “OTHER” is displayed, press the SET UP button
until “OTHER BLGT:XX” is displayed. “XX” represents the current
state. Press the UP or DOWN buttons to set the backlight to turn
“OFF” after 20 seconds or “ON” to stay on at all times.
Operating Modes:
The Encore Profile 1000 Color has six operating modes:
• RGBW Dimmer Mode - Choose one of the four colors to remain
static or adjust the intensity of each color to make your desired
color.
• Color Change mode - There are 16 color change modes to choose
from. In color change mode the unit will cycle through various col ors depending on the color change mode that is chosen. The color
change speed is also adjustable.
• Color Fade mode - There are 16 color fade modes to choose from.
In color fade mode the unit will cycle/fade through various colors
depending on the color fade mode that is chosen. The fade speed
is also adjustable.
• Auto Mode - In Auto mode, the fixture will run a combination of
color change and color fade. The speed is adjustable.
• Static Color Mode - There are 64 colors to choose from.
• DMX control mode - This function will allow you to control each
individual fixtures traits with a standard DMX 512 controller.
Encore Profile 1000 Color Photometric Chart
Encore Profile 1000 Color CAD Drawing
188.6mm/7.425”
173.6mm/6.834”
557.3mm/21.94”
264.02mm/10.394”
373.49mm/14.70”
RGBW Dimmer Mode:
1. Plug the fixture in and press the MODE button until “MANUAL” is
displayed. Press the SET UP button to cycle through the RGBW
colors.
2. When “RED” is displayed you are in Red dimming mode. Press
the UP and DOWN buttons to adjust intensity.
3. When “GREN” is displayed you are in Green dimming mode.
Press the UP and DOWN buttons to adjust intensity.
4. When “BLUE” is displayed you are in Blue dimming mode. Press
the UP and DOWN buttons to adjust intensity.
5. When “WHIT” is displayed you are in White dimming mode. Press
the UP and DOWN buttons to adjust intensity.
ADJ Products, LLC - www.adj.com - Encore Prole 1000 Color User Manual Page 7
ADJ Products, LLC - www.adj.com - Encore Prole 1000 Color User Manual Page 24
Page 9
Encore Profile 1000 Color Color Macro Chart
Encore Profile 1000 Color Operating Instructions
6. After you have adjusted the RGBW colors to make your desired
color you can then activate strobing by pressing the SET UP but ton to enter strobing.
7. “STRO” will be displayed, this is strobing mode. The strobing can
be adjusted between “00” (strobing off) to “15” (fastest strobing).
Color Change Mode:
1. Plug the fixture in and press the MODE button until “JUMP RUN
SNAP:XX” is displayed. “XX” represents a number between 01-16.
RGBW COLOR INTENSITY
2. Use the UP and DOWN buttons to find your desired color change
mode.
3. Press the SET UP button and “SPEED:XX” will be displayed. Use
the UP and DOWN buttons to adjust the speed of the color
change. The speed can be adjusted between “01” (slowest) to
VAULE
“16” (fastest).
Color Fade Mode:
1. Plug the fixture in and press the MODE button until “FADE RUN
FADE:XX” is displayed. “XX” represents a number between 01-16.
2. Use the UP and DOWN buttons to find your desired color fade
mode.
3. Press the SET UP button and “SPEED:XX” will be displayed. Use
the UP and DOWN buttons to adjust the speed of the color fade.
The speed can be adjusted between “01” (slowest) to “16” (fast est).
Auto Run Mode:
RGBW COLOR INTENSITY Color No. DMX
1. Plug the fixture in and press the MODE button until “AUTO RUN
FAD+SNAP” is displayed.
RED GREEN BLUE WHITE RED GREEN BLUE WHITE
2. Press the SET UP button and “SPEED:XX” will be displayed. Use
the UP and DOWN buttons to adjust the speed of the Auto Run.
The speed can be adjusted between “01” (slowest) to “16” (fast-
VAULE
est).
Color No. DMX
OFF 0 0 0 0 0 Color33 129-132 255 206 1 43 0
Color1 1-4 80 255 234 8 0 Color34 133-136 254 177 153 0
Color2 5-8 80 255 164 80 Color35 137-140 254 192 138 0
Color3 9-12 77 255 112 77 Color36 141-144 254 165 98 0
Color4 13-16 117 255 83 83 Color37 145-148 254 121 0 0
Color5 17-20 160 255 77 77 Color38 149-152 176 17 0 0
Color6 21-24 223 255 83 83 Color39 153-156 96 0 11 0
Color7 25-28 255 243 77 77 Color40 157-160 234 139 171 0
Color8 29-32 255 200 74 74 Color41 161-164 224 5 97 0
Color9 33-36 255 166 77 77 Color42 165-168 175 77 173 0
Color10 37-40 255 125 74 74 Color43 169-172 119 130 199 0
Color11 41-44 255 97 77 74 Color44 173-176 147 164 212 0
Color12 45-48 255 71 77 71 Color45 177-180 88 2 163 0
Color13 49-52 255 83 134 83 Color46 181-184 0 38 86 0
Color14 53-56 255 93 182 93 Color47 185-188 0 142 208 0
Color15 57-60 255 96 236 96 Color48 189-192 52 148 209 0
Color16 61-64 238 93 255 93 Color49 193-196 1 134 201 0
Color17 65-68 196 87 255 87 Color50 197-200 0 145 212 0
Color18 69-72 150 90 255 90 Color51 201-204 0 121 192 0
Color19 73-76 100 77 255 77 Color52 205-208 0 129 184 0
Color20 77-80 77 100 255 77 Color5 3 209-212 0 83 115 0
Color21 81-84 67 148 255 6 7 Color54 213-216 0 97 166 0
Color22 85-88 77 195 255 7 7 Color55 217-220 1 100 167 0
Color23 89-92 77 234 255 7 7 Color56 221-224 0 40 86 0
Color24 93-96 158 255 144 144 Color57 225-228 209 219 182 0
Color25 97-100 255 251 153 153 Colo r58 229-232 42 165 85 0
Color26 101-104 255 175 147 147 Color59 233-236 0 46 35 0
Color27 105-108 255 138 186 138 Color60 237-240 8 107 222 0
Color28 109-112 255 147 251 147 Color61 241-244 107 156 231 0
Color29 113-116 151 138 255 138 Color62 245-248 165 198 247 0
ADJ Products, LLC - www.adj.com - Encore Prole 1000 Color User Manual Page 23
Static Color Mode:
Color30 117-120 99 0 255 100 Color63 249-252 0 0 189 0
Color31 121-124 138 169 255 138 Color64 253-255 255 255 255 0
Color32 125-128 255 255 255 255
1. Plug the fixture in and press the MODE button until “CLR MACS
COLOR:XX” is displayed. “XX” represents a number between
00-64.
2. Use the UP and DOWN buttons to scroll through the 64 colors
and find you desired color. After you have found your desired
ADJ Products, LLC - www.adj.com - Encore Prole 1000 Color User Manual Page 8
Page 10
Encore Profile 1000 Color Operating Instructions
Encore Profile 1000 Color 11 Channel Mode
color you can activate strobing by pressing the SET UP button to
enter the strobe mode.
3. “STROB:XX” will be displayed, this is strobe mode. The strobing
can be adjusted between “00” (flash off) to “15” (fastest flash).
DMX Mode:
Operating through a DMX controller gives the user the freedom to
create their own programs tailored to their own individual needs.
The Encore Profile 1000 Color has 5 DMX modes: 4 channel mode,
5 channel mode, 6 channel mode, 10 channel mode, and 11 channel
mode. See page’s 14-22 for each mode’s DMX traits.
1. This function will allow you to control each individual fixture’s
traits with a standard DMX 512 controller.
2. To run your fixture in DMX mode press the MODE button until
“DMX MODE:XXX” is displayed. “XXX” represents the current
displayed DMX address. Use the UP or DOWN buttons to select
your desired DMX address, then press the SETUP button to select
your DMX channel mode.
3. Use the UP or DOWN buttons to scroll through the DMX channel
modes. The channel modes are listed below:
• “CHAN: 04” is 4 Channel DMX Mode.
• “CHAN: 05” is 5 Channel DMX Mode.
• “CHAN: 06” is 6 Channel DMX Mode.
• “CHAN: 10” is 10 Channel DMX Mode.
• “CHAN: 11” is 11 Channel DMX Mode.
4. Please see pages 14-22 for DMX values and traits.
5. After you have chosen your desired DMX Channel mode plug in
the fixture via the XLR connections to any standard DMX control ler.
Channel Value Function
11 DIMMER CURVES
0 - 20 STANDARD
21 - 40 STAGE
41 - 60 TV
61 - 80 ARCHITECTURAL
81 - 100 THEATRE
101 - 255 DEFAULT TO UNIT SETTING
When Channel 7 is between the values of 0-51, Channels 1-4 are used, and
Channel 6 will control strobing.
When Channel 7 is between the values of 52-102, Channel 8 is in Color Macros
Mode, and Channel 6 will control strobing.
When Channel 7 is between the values of 103-153, Channel 8 is in Color Change
Mode, and Channel 9 will control the color change speed.
When Channel 7 is between the values of 154-204, Channel 8 is in Color Fade
Mode, and Channel 9 will control the color fade speed.
When Channel 7 is between the values of 205-255, Channel 8 is in Auto Run
Mode, and Channel 9 will control the Auto Run speed.
System Reset:
This will return the fixture to its factory settings.
1. Plug the fixture in and press the MODE button until “OTHER
MODE” is displayed.
2. Press the SET UP button until “SYSRESET” is displayed.
3. Press the UP and DOWN buttons simultaneously to reset or press
the MODE button to exit.
ADJ Products, LLC - www.adj.com - Encore Prole 1000 Color User Manual Page 9
ADJ Products, LLC - www.adj.com - Encore Prole 1000 Color User Manual Page 22
Page 11
Encore Profile 1000 Color 11 Channel Mode
Encore Profile 1000 Color Operating Instructions
Channel Value Function
8 COLOR MACROS/PROGRAMS/
AUTO RUN
COLOR CHANGE PROGRAMS
192 - 207 COLOR CHANGE 13
208 - 223 COLOR CHANGE 14
224 - 239 COLOR CHANGE 15
240 - 255 COLOR CHANGE 16
COLOR FADE PROGRAMS
0 - 15 COLOR FADE 1
16 - 31 COLOR FADE 2
32 - 47 COLOR FADE 3
48 - 63 COLOR FADE 4
64 - 79 COLOR FADE 5
80 - 95 COLOR FADE 6
96 - 111 COLOR FADE 7
112 - 127 COLOR FADE 8
128 - 143 COLOR FADE 9
144 - 159 COLOR FADE 10
160 - 175 COLOR FADE 11
176 - 191 COLOR FADE 12
192 - 207 COLOR FADE 13
208 - 223 COLOR FADE 14
224 - 239 COLOR FADE 15
240 - 255 COLOR FADE 16
9 PROGRAM SPEED
0 - 255 SLOW - FAST
10 COLOR TEMPERATURE
0 - 28 3200K
29 - 57 3500K
58 - 86 4200K
87 - 114 4500K
115 - 142 5200K
143 - 170 5500K
171 - 198 6200K
199 - 226 6500K
227 - 255 7200K
ADJ Products, LLC - www.adj.com - Encore Prole 1000 Color User Manual Page 21
Dimmer Curve:
This is used to set the dimming curve used with DMX mode. See
page 29 for the different dimming curves.
1. Plug the fixture in and press the MODE button until “DMX MODE
ADDR:XXX” is displayed.
2. Press the SET UP button until “DELAY:X” is displayed. “X” repre-
sents the displayed dimmer curve (0-4).
• 0 - Standard
• 1 - Stage
• 2 - TV
• 3 - Architectural
• 4 - Theatre
3. Press the UP or DOWN buttons to scroll through and select
your desired dimming curve.
DMX State:
This mode can be used as a precaution mode, that in case the DMX
signal is lost, the operating mode chosen in the setup is the running
mode the xture will go into when the DMX signal is lost. You can also
set this as the operating mode you would like the unit to return to
when power is applied.
1. Plug the fixture in and press the MODE button until “DMX MODE
ADDR:XXX” is displayed.
2. Press the SET UP button until “DMX MODE NO” is displayed. The
current DMX state will be displayed.
• “BLACK” (Blackout) - If the DMX signal is lost or interrupted,
the unit will automatically go into stand by mode.
• “HOLD” (Last State) - If the DMX signal is lost or interrupted,
the xture will stay in the last DMX set up.
• “AUTO” (Auto Run) - If the DMX signal is lost or interrupted,
the unit will automatically go into Auto Run mode.
3. Press the UP or DOWN buttons to scroll through and select
your desired DMX state.
ADJ RFC:
This function is used to activate and deactivate the infared sensor. When this function is activated you can control the fixture using
the ADJ LED RC2 (sold separately), UC IR (sold separately), and
Airstream IR app. Please see pages 13-15 for remote controls and
ADJ Products, LLC - www.adj.com - Encore Prole 1000 Color User Manual Page 10
Page 12
Encore Profile 1000 Color Operating Instructions
Encore Profile 1000 Color 11 Channel Mode
functions. To control the Encore Profile 1000 Color, plug the included
IR receiver into IR receiver input located on the rear of the controller.
You must aim the remote at the IR sensor and be no more the 30 feet
away.
1. Plug the fixture in and press the MODE button until “OTHER
MODE” is displayed.
2. Press the SET UP button until “IR: XX” is displayed.
3. Press the UP or DOWN buttons to either activate the remote func tion (On) or deactivate it (Off).
Color Balance Mode:
1. Plug the fixture in and press the MODE button until “BALANCE” is
displayed. Press the SET UP button for at lease 3 seconds until
the displayed number begins to flash.
2. When “RED” is displayed you are in Red balance mode. Press the
UP and DOWN buttons to adjust intensity.
3. When “GREN” is displayed you are in Green balance mode.
Press the UP and DOWN buttons to adjust intensity.
4. When “BLUE” is displayed you are in Blue balance mode. Press
the UP and DOWN buttons to adjust intensity.
5. When “WHIT” is displayed you are in White balance mode. Press
the UP and DOWN buttons to adjust intensity.
6. Press the SET UP button for 3 seconds to save your settings.
Gamma:
This feature is predominately used when shooting video. Adjust the
gamma setting to clean up any lines that might be seen on camera.
1. Plug the fixture in and press the MODE button until “GAMMA” is
displayed. The current gamma setting will be displayed.
2. Use the UP and DOWN buttons to switch the gamma setting.
Refresh Rate:
This feature is predominately used when shooting video. Adjust the
frequency setting to clear up any LED flicker that might be seen on
camera.
1. Plug the fixture in and press the MODE button until “FREQUENC”
is displayed. The current frequency setting will be displayed.
2. Use the UP and DOWN buttons to switch the frequency setting.
ADJ Products, LLC - www.adj.com - Encore Prole 1000 Color User Manual Page 11
Channel Value Function
1 RED
0 - 255 0% - 100%
2 GREEN
0 - 255 0% - 100%
3 BLUE
0 - 255 0% - 100%
4 WHITE
0 - 255 0% - 100%
5 MASTER DIMMER
0 - 255 0% - 100%
6 STROBE
0 - 15 LED OFF
16 - 255 STROBING SLOW - FAST
7 PROGRAM SELECTION MODE
0 - 51 DIMMING MODE
52 - 102 COLOR MACRO MODE
103 - 153 COLOR CHANGE MODE
154 - 204 COLOR FADE MODE
205 - 255 AUTO RUN MODE
8 COLOR MACROS/PROGRAMS/
AUTO RUN
0 - 255 COLOR MACRO MODE
(See page 23 for the Color Macro Chart)
COLOR CHANGE PROGRAMS
0 - 15 COLOR CHANGE 1
16 - 31 COLOR CHANGE 2
32 - 47 COLOR CHANGE 3
48 - 63 COLOR CHANGE 4
64 - 79 COLOR CHANGE 5
80 - 95 COLOR CHANGE 6
96 - 111 COLOR CHANGE 7
112 - 127 COLOR CHANGE 8
128 - 143 COLOR CHANGE 9
144 - 159 COLOR CHANGE 10
160 - 175 COLOR CHANGE 11
176 - 191 COLOR CHANGE 12
ADJ Products, LLC - www.adj.com - Encore Prole 1000 Color User Manual Page 20
Page 13
Encore Profile 1000 Color 10 Channel Mode
Encore Profile 1000 Color Operating Instructions
Channel Value Function
8 COLOR MACROS/PROGRAMS/
AUTO RUN
COLOR CHANGE PROGRAMS
192 - 207 COLOR CHANGE 13
208 - 223 COLOR CHANGE 14
224 - 239 COLOR CHANGE 15
240 - 255 COLOR CHANGE 16
COLOR FADE PROGRAMS
0 - 15 COLOR FADE 1
16 - 31 COLOR FADE 2
32 - 47 COLOR FADE 3
48 - 63 COLOR FADE 4
64 - 79 COLOR FADE 5
80 - 95 COLOR FADE 6
96 - 111 COLOR FADE 7
112 - 127 COLOR FADE 8
128 - 143 COLOR FADE 9
144 - 159 COLOR FADE 10
160 - 175 COLOR FADE 11
176 - 191 COLOR FADE 12
192 - 207 COLOR FADE 13
208 - 223 COLOR FADE 14
224 - 239 COLOR FADE 15
240 - 255 COLOR FADE 16
9 PROGRAM SPEED
0 - 255 SLOW - FAST
10 DIMMER CURVES
0 - 20 STANDARD
21 - 40 STAGE
41 - 60 TV
61 - 80 ARCHITECTURAL
81 - 100 THEATRE
101 - 255 DEFAULT TO UNIT SETTING
PCB Temperature:
This will check the current temperature of unit as well as switch
between fahrenheit and celsius.
1. Plug the fixture in and press the MODE button until “OTHER
MODE” is displayed.
2. Press the SET UP button until “TEM:XXXX” is displayed.
3. Use the UP and DOWN buttons to switch between fahrenheit and
celsius.
Encore Profile 1000 Color Master-Slave Configuration
Master-Slave Configuration:
This function will allows you to link units together to run in a MasterSlave setup. In a Master-Slave set up one unit will act as the controlling unit and the others will react to the controlling units built-in programs. Any unit can act as a Master or as a Slave however, only one
unit can be programmed to act as the “Master.”
Master-Slave Connections and Settings:
1. Daisy chain your units via the XLR connector on the rear of the
unit. Use standard XLR data cables to link your units together.
Remember that the Male XLR connector is the input and the
Female XLR connector is the ouput. The first unit in the chain
(master) will use the female XLR connector only. The last unit in
the chain will use the male XLR connector only.
2. Set the “Master” unit to your desired mode of operation.
3. On the “Slave” units press the MODE button until “Slave Mode” is
displayed. The unit is now set as the “Slave” unit. Each slave unit
must be set to the same setting.
4. Connect the rst “Slave” unit to the “Master”, and the “Slave” unit
should now start to follow the “Master”.
Encore Profile 1000 Color Focus and Zoom Adjustments
The knobs located on the right side of unit are used to adjust the focus
and the zoom. For a tighter/narrow beam move the first/front knob to
the front of the fixture, and move the second knob to rear. For a wider
beam, move the first/front knob towards the middle of the fixture, and
move the second knob towards the middle as well. Adjust accordingly.
ADJ Products, LLC - www.adj.com - Encore Prole 1000 Color User Manual Page 19
ADJ Products, LLC - www.adj.com - Encore Prole 1000 Color User Manual Page 12
Page 14
Encore Profile 1000 Color ADJ LED RC2 Operation
Encore Profile 1000 Color 10 Channel Mode
The ADJ LED RC2 infrared remote (sold seperately) has many dif-
fernet functions to control your Encore Profile 1000 Color. To control
the fixture you must aim the controller at the infrared sensor and be
no more the 30 feet away. To use the ADJ LED RC2 you must first
activate the fixtures infrared sensor, to activate the sensor please see
the instructions on pages 10-11.
BLACKOUT - Pressing this button will blackout the fixture.
SELECT PROG - Pressing this button will cycle through static color
mode, color change mode, color fade mode, and auto run mode.
Each press of this button will change to the next mode. When you
found your desired mode use the “+” or “-” to scroll through the programs or static colors. When in either color fade, or color change
mode, press the Speed button and use the “+” or “-” to adjust the
running speed. When in static color mode, press the Flash button to
activate strobe and use the “+” or “-” to adjust the strobe speed.
FLASH - This button will activate the strobe effect. You can control
the flash rate by pressing the “+” and “-” buttons. Press this button
again to exit strobe mode.
SPEED - Press this button and use the “+” & “-” buttons to adjust the
speed of the color change mode, color fade mode, and auto run.
DMX MODE - This button will cycle between DMX addressing, DMX
channel mode, and dimmer curve selection. Some fixtures will come
with different DMX channel modes. This button will switch between
the different modes. Please see pages 16-22 for DMX modes, values,
and traits.
SLAVE/SOUND ACTIVE - This designates the fixture as a slave fixture in a master/slave configuration. Sound activity is invalid for this
fixture.
SET ADDRESS - Press this button to set the DMX address. Press
this button first, then press the numbers to set the address. If the
address is correctly set, all LED’s will flash and the unit will automatically go into DMX mode.
Example: Set DMX Address 1 Press “S-0-0-1”
Set DMX Address 245 Press “S-2-4-5”
ADJ Products, LLC - www.adj.com - Encore Prole 1000 Color User Manual Page 13
Channel Value Function
1 RED
0 - 255 0% - 100%
2 GREEN
0 - 255 0% - 100%
3 BLUE
0 - 255 0% - 100%
4 WHITE
0 - 255 0% - 100%
5 MASTER DIMMER
0 - 255 0% - 100%
6 SHUTTER/STROBE
0 - 15 LED OFF
16 - 255 STROBING SLOW - FAST
7 PROGRAM SELECTION MODE
0 - 51 DIMMING MODE
52 - 102 COLOR MACRO MODE
103 - 153 COLOR CHANGE MODE
154 - 204 COLOR FADE MODE
205 - 255 AUTO RUN MODE
8 COLOR MACROS/PROGRAMS/
AUTO RUN
0 - 255 COLOR MACRO MODE
(See page 23 for the Color Macro Chart)
COLOR CHANGE PROGRAMS
0 - 15 COLOR CHANGE 1
16 - 31 COLOR CHANGE 2
32 - 47 COLOR CHANGE 3
48 - 63 COLOR CHANGE 4
64 - 79 COLOR CHANGE 5
80 - 95 COLOR CHANGE 6
96 - 111 COLOR CHANGE 7
112 - 127 COLOR CHANGE 8
128 - 143 COLOR CHANGE 9
144 - 159 COLOR CHANGE 10
160 - 175 COLOR CHANGE 11
176 - 191 COLOR CHANGE 12
ADJ Products, LLC - www.adj.com - Encore Prole 1000 Color User Manual Page 18
Page 15
Encore Profile 1000 Color 6 Channel Mode
Encore Profile 1000 Color ADJ LED RC2 Operation
Channel Value Function
1 RED
0 - 255 0% - 100%
2 GREEN
0 - 255 0% - 100%
3 BLUE
0 - 255 0% - 100%
4 WHITE
0 - 255 0% - 100%
5 MASTER DIMMER
0 - 255 0% - 100%
6 SHUTTER/STROBE
0 - 15 LED OFF
16 - 255 STROBING SLOW - FAST
R G B W - Press either one of these buttons and the press the “+”
or “-” to adjust the brightness. Press the FLASH button to activate
strobing and use the “+” or “-” to adjust the flash speed.
“+” and “-” - These buttons adjust the flash rate and speed of the
color change mode, color fade mode, and auto run. When in color
change or color fade mode they are used to find your desired program. See color change mode and color fade mode on page 8.
DMX Mode:
Operating through a DMX controller gives the user the freedom to
create their own programs tailored to their own individual needs.
Follow the directions below to set your DMX address and DMX channel mode.
1. Before connecting to a DMX controller, your fixture has different
DMX channel modes, please select your desired mode by press ing the DMX Mode button, then using the “+” or “-” buttons to
scroll through the DMX channel modes. Set the mode before you
address the fixture. See the bottom of this page for the different
DMX modes.
2. After you have selected your mode, set the DMX address for the
fixture by pressing the “S” button. When the “S” button is pressed
the LED’s will flash 2-3 times. Use the number buttons to press in
your desired address. See “SET ADDRESS” on page 13 for
examples.
Note: When seeting the DMX address each time a number is pressed
a LED color will flash, when you have set the DMX address correctly
all LED’s will flash 2-3 times.
ADJ Products, LLC - www.adj.com - Encore Prole 1000 Color User Manual Page 17
3. Now you may connect the fixture via the XLR connections to any
standard DMX controller. Please see pages 16-22 to for a detailed
descriptions of the DMX modes, values, and traits.
• If the Red LED flashes you are in 4 Channel Mode.
• If the Green LED flashes you are in 5 Channel Mode.
• If the Blue LED flashes you are in 6 Channel Mode.
• If the White LED flashes you are in 10 Channel Mode.
• If the Red & Green LED’s flash you are in 11 Channel Mode.
ADJ Products, LLC - www.adj.com - Encore Prole 1000 Color User Manual Page 14
Page 16
Encore Profile 1000 Color UC IR Remote & Airstream IR
Encore Profile 1000 Color 4 Channel Mode
The UC IR (sold separately) infrared remote gives you control of
various functions (See below). To control the fixture you must aim the
remote at the front of the fixture and be no more than 30 feet away.
The Airstream IR (sold separately) remote transmitter plugs into the
headphone jack of your iOS phone or tablet. To control your IR fixture
you must raise the volume to the maximum on your iOS phone or tablet and aim the transmitter at the fixture sensor and be no more than
15 feet away. After you have purchased the Airstream IR transmitters,
the app is a free download from the app store for your iOS phone
or tablet. The app comes with 3 pages of control depending on the
fixture you are using. Please see below for IR functions including the
corresponding app page.
Works with App page 1.
STAND BY - Pressing this button will blackout the fixture. Press the
button again to return to the initial state.
FULL ON - Hold this button down to fully light up the unit. When you
let the button go, the unit will return to its previous state.
FADE/GOBO - Pressing this button activates color fade mode. .
“DIMMER +” and “DIMMER -” - Use these buttons adjust output in-
tensity in color mode.
STROBE - Press and hold this button for strobing.
COLOR - Press this button to activate color mode. Use buttons 1-9
to select your desired color. Use the “DIMMER+” and “DIMMER-” to
scroll through the colors.
Channel Value Function
1 RED
0 - 255 0% - 100%
2 GREEN
0 - 255 0% - 100%
3 BLUE
0 - 255 0% - 100%
4 WHITE
0 - 255 0% - 100%
Encore Profile 1000 Color 5 Channel Mode
Channel Value Function
1 RED
0 - 255 0% - 100%
2 GREEN
0 - 255 0% - 100%
3 BLUE
0 - 255 0% - 100%
4 WHITE
0 - 255 0% - 100%
5 MASTER DIMMER
0 - 255 0% - 100%
1-9 - Use these buttons to select your desired color or show when
show mode is active. Use the “DIMMER+” and “DIMMER-” buttons to
adjust the output intensity.
SHOW 0 - Press this button to activate show mode. Use buttons
1-9 to select shows 1-9. Press this button twice to run show 10, and
press button 1 to run show 11.
ADJ Products, LLC - www.adj.com - Encore Prole 1000 Color User Manual Page 15
ADJ Products, LLC - www.adj.com - Encore Prole 1000 Color User Manual Page 16
Loading...