ADJ ENCORE LP12IP User Manual [EN]

ENCORE LP12IP

User Manual

©2021 ADJ Products, LLC all rights reserved. Information, specications, diagrams, images, and

instructions herein are subject to change without notice. ADJ Products, LLC logo and identifying
product names and numbers herein are trademarks of ADJ Products, LLC. Copyright protection
claimed includes all forms and matters of copyrightable materials and information now allowed by
statutory or judicial law or hereinafter granted. Product names used in this document may be trade­marks or registered trademarks of their respective companies and are hereby acknowledged. All
non-ADJ Products, LLC brands and product names are trademarks or registered trademarks of their
respective companies.

ADJ Products, LLC and all aliated companies hereby disclaim any and all liabilities for property,

equipment, building, and electrical damages, injuries to any persons, and direct or indirect economic
loss associated with the use or reliance of any information contained within this document, and/or as
a result of the improper, unsafe, insucient and negligent assembly, installation, rigging, and opera­tion of this product.

DOCUMENT VERSION

Due to additional product features and/or enhancements, an updated version of
this document may be available online.
Please check www.adj.com for the latest revision/update of this manual
before beginning installation and/or programming.

Date

12/30/2021 1.0 1.02

Europe Energy Saving Notice
Energy Saving Matters (EuP 2009/125/EC)

Saving electric energy is a key to help protecting the enviroment. Please turn o all electrical products when

they are not in use. To avoid power consumption in idle mode, disconnect all electrical equipment from power
when not in use. Thank you!

Document

Version

Software

Version

DMX Channels Notes

4 / 7 / 8 / 10 / 13 / 16

channels

2

Initial Release.

TABLE OF CONTENTS

Introduction 4

Limited Warranty (USA Only) 5

Warranty Registration | Features 6

Safety Guidelines 7

Overview 8

Installation 9

Control Panel 12

System Menu 13

DMX Setup 16

DMX Traits 18

Color Macros Chart 21

Dim Modes 23

Daisy Chain Power Linking | Cleaning and Maintenance 24

Dimensional Drawings 25

Specifications 26

Accessory and Ordering Information 27

3

INTRODUCTION

Unpacking: Thank you for purchasing the Encore LP12IP by ADJ Products, LLC. Every Encore LP12IP
has been thoroughly tested and has been shipped in perfect operating condition. Carefully check the
shipping carton for damage that may have occurred during shipping. If the carton appears to be dam-

aged, carefully inspect your xture for any damage and be sure all accessories necessary to operate

the unit have arrived intact. In the event that damage has been found or parts are missing, please
contact our toll free customer support number for further instructions. Do not return this unit to your

dealer without rst contacting customer support.

Introduction: The ADJ Encore LP12IP is a DMX intelligent, heavy duty Par. To optimize the perfor­mance of this product, please read these operating instructions carefully to familiarize yourself with
the basic operations of this unit. These instructions contain important safety information regarding the
use and maintenance of this unit. Please keep this manual with the unit for future reference.

Customer Support: Contact ADJ Service for any product related service and support needs. Also visit

forums.adj.com with questions, comments or suggestions.

Parts: To purchase parts online visit:

http://parts.adj.com (US)
http://www.adjparts.eu (EU)

ADJ SERVICE USA - Monday - Friday 8:00am to 4:30pm PST
Voice: 800-322-6337 | Fax: [phone] | [e-mail]

ADJ SERVICE EUROPE - Monday - Friday 08:30 to 17:00 CET
Voice: [phone] | Fax: [phone] | [e-mail]

ADJ PRODUCTS LLC USA

6122 S. Eastern Ave. Los Angeles, CA. 90040
323-582-2650 | Fax [phone] | www.adj.com | [e-mail]

ADJ SUPPLY Europe B.V

Junostraat 2 6468 EW Kerkrade, The Netherlands

[phone] | Fax [phone]

www.americandj.eu | [e-mail]

ADJ PRODUCTS GROUP Mexico

AV Santa Ana 30 Parque Industrial Lerma, Lerma, Mexico 52000

[phone]

CAUTION! There are no user serviceable parts inside this unit. Do not attempt any repairs yourself,
as doing so will void your manufacturer’s warranty. In the unlikely event your unit may require service,
please contact ADJ Products, LLC.

Do not discard the shipping cartoon in the trash. Please recycle when ever possible.

4

LIMITED WARRANTY (USA ONLY)

A. ADJ Products, LLC hereby warrants, to the original purchaser, ADJ Products, LLC products to be free of

manufacturing defects in material and workmanship for a prescribed period from the date of purchase

(see specic warranty period on reverse). This warranty shall be valid only if the product is purchased

within the United States of America, including possessions and territories. It is the owner’s responsibility
to establish the date and place of purchase by acceptable evidence, at the time service is sought.

B. For warranty service, you must obtain a Return Authorization number (RA#) before sending the product

back—please contact ADJ Products, LLC Service Department at 800-322-6337. Send the product only to
the ADJ Products, LLC factory. All shipping charges must be prepaid. If the requested repairs or service
(including parts replacement) are within the terms of this warranty, ADJ Products, LLC will pay return ship­ping charges only to a designated point within the United States. If the entire instrument is sent, it must be
shipped in its original package and packaging material. No accessories should be shipped with the prod­uct. If any accessories are shipped with the product, ADJ Products, LLC shall incur no liability whatsoever
for loss of or damage to any such accessories, nor for the safe return thereof.

C. This warranty is void if the product serial number and/or labels are altered or removed; if the product is

modied in any manner which ADJ Products, LLC concludes, after inspection, aects the reliability of the

product; if the product has been repaired or serviced by anyone other than the ADJ Products, LLC factory
unless prior written authorization was issued to purchaser by ADJ Products, LLC; if the product is dam­aged because it was not properly maintained as set forth in the product instructions, guidelines and/or
user manual.

D. This is not a service contract, and this warranty does not include maintenance, cleaning, or periodic

checkup. During the period specied above, ADJ Products, LLC will replace defective parts at its expense
with new or refurbished parts, and will absorb all expenses for warranty service and repair labor by reason

of defects in material or workmanship. The sole responsibility of ADJ Products, LLC under this warranty
shall be limited to the repair of the product, or replacement thereof, including parts, at the sole discretion
of ADJ Products, LLC. All products covered by this warranty were manufactured after August 15, 2012,

and bear identifying marks to that eect.

E. ADJ Products, LLC reserves the right to make changes in design and/or improvements upon its products

without any obligation to include these changes in any products theretofore manufactured.

F. No warranty, whether expressed or implied, is given or made with respect to any accessory supplied with

products described above. Except to the extent prohibited by applicable law, all implied warranties made
by ADJ Products, LLC in connection with this product, including warranties of merchantability or tness,
are limited in duration to the warranty period set forth above. And all warranties, whether expressed or
implied, including warranties of merchantability or tness, are limited in duration to the warranty period set
forth above. The consumer’s and/or dealer’s sole remedy shall be such repair or replacement as is ex-

pressly provided above; and under no circumstances shall ADJ Product, LLC be liable for any loss and/or
damage, direct and/or consequential arising out of the use of, and/or inability to use this product.

G. This warranty is the only written warranty applicable to ADJ Products, LLC products, and supersedes all

prior warranties and written descriptions of warranty terms and conditions heretofore published.

MANUFACTURER’S LIMITED WARRANTY PERIODS:

• Non-LED Lighting Products = 1-Year (365 Days) (Including Special Eect Lighting, Intelligent Lighting,

UV lighting, Strobes, Fog Machines, Bubble Machines, Mirror Balls, Par Cans, Trussing, Lighting Stands,

Power/Data Distribution, etc. excluding LED and lamps)

• Laser Products = 1-Year (365 Days) (excluding laser diodes which have a 6-Month Limited Warranty)

• LED Products = 2-Year (730 Days) (excluding batteries which have a 180 Day Limited Warranty)

• NOTE: 2-Year (730 Days) Limited Warranty ONLY applies to product purchased within the United States.
StarTec Series = 1-Year (365 Days) (excluding batteries which have a 180 Day Limited Warranty)

• ADJ DMX Controllers = 2 Year (730 Days)

• American Audio Products = 1 Year (365 Days)

5

WARRANTY REGISTRATION

The Encore LP12IP carries a 2 year limited warranty. Please ll out the enclosed warranty card to

validate your purchase. All returned service items, whether under warranty or not, must be freight pre­paid and accompanied by a return authorization (R.A.) number. The R.A. number must be clearly writ­ten on the outside of the return package. A brief description of the problem as well as the R.A. num­ber must also be written down on a piece of paper included in the shipping carton. If the unit is under
warranty, you must provide a copy of your proof of purchase invoice. You may obtain an R.A. number
by contacting our customer support team on our customer support number. All packages returned to
the service department not displaying an R.A. number on the outside of the package will be returned
to the shipper.

FEATURES

The ADJ Encore LP12IP is a versatile, heavy duty Par with twelve (12) 20W Quad LEDs (4-IN-1: Red,
Green, Blue & Lime), a 10-degree beam angle, and all metal construction. It is IP65 outdoor rated to
protect against, rain, snow and dust for temporary outdoor events. It offers flicker free operation for
TV and film and linear white color temperature control from 2700K - 6500K.

INCLUDED ITEMS

• Power Cord (x1)

• Bracket Yoke (x1)

• Frost Filter (x1)

IP RATING
This device is IP65 rated. This means that the unit is dust-tight, and protected against low­pressure jets of water from any direction.

6

SAFETY GUIDELINES

THIS FIXTURE IS COMPOSED OF SOPHISTICATED ELECTRONIC COMPONENTS. TO GUARANTEE
SMOOTH OPERATION, IT IS IMPORTANT TO FOLLOW ALL INSTRUCTIONS AND GUIDELINES IN
THIS MANUAL. ADJ PRODUCTS, LLC IS NOT RESPONSIBLE FOR INJURY AND/OR DAMAGES
RESULTING FROM THE MISUSE OF THIS FIXTURE DUE TO THE DISREGARD OF THE INFORMATION
PRINTED IN THIS MANUAL. ONLY QUALIFIED AND/OR CERTIFIED PERSONNEL SHOULD PERFORM
INSTALLATION OF THIS FIXTURE AND ONLY THE ORIGINAL RIGGING PARTS INCLUDED WITH THIS
FIXTURE SHOULD BE USED FOR INSTALLATION. ANY MODIFICATIONS TO THE FIXTURE AND/OR
THE INCLUDED MOUNTING HARDWARE WILL VOID THE ORIGINAL MANUFACTURER’S WARRANTY
AND INCREASE THE RISK OF DAMAGE AND/OR PERSONAL INJURY. ONLY CERTIFIED PERSONNEL
SHOULD PERFORM INSTALLATION OF THIS FIXTURE.

• PROTECTION CLASS 1 - FIXTURE MUST BE PROPERLY GROUNDED.

• THERE ARE NO USER SERVICEABLE PARTS INSIDE THIS UNIT.

• DO NOT ATTEMPT ANY REPAIRS YOURSELF; DOING SO WILL VOID YOUR MANUFACTURER’S

WARRANTY. DAMAGES RESULTING FROM MODIFICATIONS TO THIS FIXTURE AND/OR THE
DISREGARD OF SAFETY INSTRUCTIONS AND GUIDELINES IN THIS MANUAL VOID THE
MANUFACTURER’S WARRANTY AND ARE NOT SUBJECT TO ANY WARRANTY CLAIMS AND/OR
REPAIRS.

• DO NOT PLUG FIXTURE INTO A DIMMER PACK!

• NEVER OPEN THIS FIXTURE WHILE IN USE!

• UNPLUG POWER BEFORE SERVICING FIXTURE!

• NEVER TOUCH FIXTURE DURING OPERATION, AS IT MAY BE HOT!

• KEEP FLAMMABLE MATERIALS AWAY FROM FIXTURE!

• NEVER LOOK DIRECTLY INTO THE LIGHT SOURCE!

• RETINA INJURY RISK - MAY INDUCE BLINDNESS!

• SENSITIVE PERSONS MAY SUFFER AN EPILEPTIC SHOCK!

• MINIMUM DISTANCE TO OBJECTS/SURFACES IS 6.6 FEET (2 METERS)

• MAXIMUM AMBIENT TEMPERATURE IS 113° F (45°C). DO NOT OPERATE THE DEVICE WHEN
AMBIENT TEMPERATURE EXCEEDS THIS VALUE.

• MINIMUM DISTANCE TO FLAMMABLE MATERIALS FROM THE SURFACE IS 1.6 FEET (0.5 METER).

• DO NOT TOUCH the xture housing during operation. Turn OFF the power and allow approximately 60
minutes for the xture to cool down before serving.

• DO NOT shake xture, and avoid brute force when installing and/or operating xture.

• DO NOT operate xture if the power cord is frayed, crimped, damaged and/or if any of the power cord
connectors are damaged and do not insert into the xture securely with ease. NEVER force a power cord
connector into the xture. If the power cord or any of its connectors are damaged, replace it immediately

with a new one of the same power rating.

• DO NOT block any air ventilation slots. All fan and air inlets must remain clean and never blocked. Allow
approx. 6” (15cm) between xture and other devices or a wall for proper cooling.

• When installing xture in a suspended environment, always use mounting hardware that is no less than
M10 x 25 mm, and always install xture with an appropriately rated safety cable.

• Always disconnect xture from main power source before performing any type of service and/or cleaning

procedure.

• Only handle the power cord by the plug end. Never pull out the plug by tugging the wire portion of the
cord.

• During the initial operation of this xture, a light smoke or smell may emit from the interior of the xture.
This is a normal process and is caused by excess paint in the interior of the casing burning off from the

heat associated with the lamp and will decrease gradually over time.

• Consistent operational breaks will ensure xture will function properly for many years.

• ONLY Use original packaging and materials to transport the xture in for service.

7

OVERVIEW

8

INSTALLATION

FLAMMABLE MATERIAL WARNING

Keep xture minimum 5.0 feet (1.5m) away from flammable materials and/or pyrotech­nics.

ELECTRICAL CONNECTIONS

A qualied electrician should be used for all electrical connections and/or installations.

USE CAUTION WHEN POWER LINKING FIXTURES OF OTHER MODEL TYPES, AS
THE POWER CONSUMPTION OF OTHER MODEL FIXTURES MAY EXCEED THE
MAX POWER OUTPUT ON THIS FIXTURE. CHECK SILK SCREEN FOR MAX AMPS.

MINIMUM DISTANCE TO OBJECTS/SURFACES IS 6.6 FEET (2 METERS).
MINIMUM DISTANCE OF INFLAMMABLE MATERIALS FROM THE SURFACE IS 1.6
FEET (0.5 METER)

DO NOT INSTALL THE FIXTURE IF YOU ARE NOT QUALIFIED TO DO SO!

• Fixture MUST be installed following all local, national, and country commercial electrical and con­struction codes and regulations.

• Before rigging/mounting a single xture or multiple xtures to any metal truss/structure or placing
the xture(s) on any surface, a professional equipment installer MUST be consulted to determine
if the metal truss/structure or surface is properly certied to safely hold the combined weight of
the xture(s), clamps, cables, and accessories.

• Maximum fixture ambient operating temperature is 113°F (45°C). Do not use operate the fixture
when ambient temperature exceeds this value!

• Fixture(s) should be installed in areas outside walking paths, seating areas, or areas were unau­thorized personnel might reach the xture by hand.

• NEVER stand directly below the xture(s) when rigging, removing or servicing.

• Overhead xture installation must always be secured with a secondary safety attachment, such

as an appropriately rated safety cable.

• Allow approximately 60 minutes for the xture to cool down before servicing.

IP RATING
This device is IP65 rated. This means that the unit is dust-tight, and protected against low­pressure jets of water from any direction.

RIGGING
Overhead rigging requires extensive experience, including calculating working load limits,
installation material being used, and periodic safety inspection of all installation material and

thefixture,amongotherskills.Ifyoulackthesequalifications,donotattempttheinstallation

yourself. Improper installation can result in bodily injury.

9

INSTALLATION

CLAMP INSTALLATION

This fixture features a mounting point on the yoke for the attachment of an Omega bracket and
mounting clamp. There is also a safety cable loop located on the rear of the fixture near the display
screen (see the illustration below). When mounting the fixture to a truss or any other suspended or

overhead installation, be sure to secure appropriately rated clamps and Omega brackets (not includ­ed) to the yoke, and attach a separate SAFETY CABLE of the appropriate weight rating to the safety
cable loop.

SAFETY CABLE:

ALWAYS ATTACH A SAFETY CABLE WHENEVER INSTALLING THIS FIXTURE

IN A SUSPENDED ENVIRONMENT TO ENSURE THAT THE FIXTURE WILL NOT

FALL IF THE CLAMP FAILS.

CONNECTIONS

Ensure all connections and end caps are properly sealed with a dielectric grease (available at most
electrical suppliers) to prevent corrosion, water intrusion, and/or electrical short circuiting. In order

to maintain IP65 rating integrity and prevent water from entering the fixture, all unused con­nections must be sealed by closing their protective rubber caps.

10

INSTALLATION

POTENTIAL INTERNAL FIXTURE DAMAGE FROM EXTERNAL SOURCES OF LIGHT BEAMS

External sources of light beams from direct sunlight, lighting moving head fixtures, and lasers which
are focused directly towards the exterior housing and/or penetrate the front lens opening of ADJ
lighting fixtures can cause severe internal damage including burning of optics, dichroic color filters,

glass and metal gobos, prisms, animation wheels, frost filters, irises, shutters, motors, belts, wiring,
discharge lamps, and LEDs.

This issue is not unique to ADJ lighting fixtures; it is a common issue with lighting fixtures from all

manufacturers. Although there is no true way to fully prevent this issue from happening, the guide­lines below can reduce the risk of any potential damage if followed. Contact ADJ Service for more
details.

DO NOT EXPOSE THE FIXTURE AND/OR FRONT LENS OPENING TO LIGHT BEAMS FROM
DIRECT SUNLIGHT, OTHER LIGHTING MOVING HEAD FIXTURES, AND LASERS DURING
UNPACKING, INSTALLATION, USE, AND EXTENDED IDLE TIMES OUTDOORS. DO NOT FOCUS
A LIGHT BEAM FROM ONE LIGHTING FIXTURE DIRECTLY TOWARDS ANOTHER.

11

CONTROL PANEL

The xture includes an easy to navigate system menu control panel display where all necessary set­tings and adjustments are made. (See image below)

• MODE: Cycles through the main menu options and/or return to previous menu without making
changes.

• DOWN/UP: Scroll through options in the selected menu.

• ENTER: Select highlighted option and/or confirm selection.

This device features two different settings for locking the keypad. Setting Lock to “ON” requires the

user to simply press and hold the MODE button for 10 seconds to unlock the keypad.

Setting Lock to “ON1” provides an additional safeguard against accidental unlocking by requiring
a passcode to unlock the device. To unlock, press the MODE button so that “LOCKED *****” is dis-

played on the screen, then press UP DOWN UP DOWN ENTER in that particular order. Each button

press will remove one asterisk from the LOCKED text on the display screen.

12

SYSTEM MENU

DMX SET

Address

Ch. Mode

No DMX

Primary

Secondary

Fan Set

001 - 512

4ch

7ch

8ch

10ch

13ch

16ch

Hold

Blackout

Int. Prog

On / O

On / O

Auto

High

Set DMX address of the unit.

Set DMX channel mode.

Unit holds last setting if
DMX signal is lost.

Unit goes to standby mode
if DMX signal is lost.

Unit default to last internal
program when DMX signal
is lost.

Set primary mode.

Set secondary mode.

PERSONALITY

Dim Mode

Dim Curve

LED Rfrsh

Display

Silent

Standard

Stage

TV

Archi.

Theatre

Stage 2

Dim Speed 0.1s - 10s

Square

Linear

Inv. Squa

S. Curve

900, 1000, 1100, 1200, 1300, 1400, 1500, 2500,
4000, 5000, 10k, 15k, 20k, 25k

SaveDelay

Lock

1 - 10

ON

ON1

Set LED refresh rate.

Press MODE for 10s to
unlock

Press MODE and display
shows LOCKED *****. To
unlock, press UP DOWN UP
DOWN ENTER.

OFF Keypad is unlocked

CONTINUED ON NEXT PAGE

13

SYSTEM MENU

Red 000 - 255

PERSONALITY
(continued)

MANUAL

Calibrat

Service

Red 000 - 255

Blue 000 - 255

Green 000 - 255

Lime 000 - 255

ClrMacro 00 - 64

ClrTemp 000 - 255

ClrTeMac 000 - 255 Color Temp Macros.

Strobe 000 - 255

MastrDim 000 - 255

AutoProg 000 - 255

ProgSpd 000 - 255

Passcode =
050

S. Update

Restore: Pass­code = 011

Green 000 - 255

Blue 000 - 255

Lime 000 - 255

Yes / No

Yes / No

Restore the unit to factory
settings.

INTPROGS

INFO

ProgFade 000 - 255

Speed 000 - 255

Prog 0

Fade 000 - 255

Speed 000 - 255

Prog 1

Fade 000 - 255

... ... ...

Speed 000 - 255

Prog 7

Fade 000 - 255

PwrOnHr1 xxx Hrs

Hours

PwrOnHr2 xxx Hrs

PwrOnRst Passcode = 050 Reset hours to zero.

xxx° xxx F / xxx C

MaxTemp1 xxx F / xxx C Max temp since last reset.

Temp.

MaxTemp2 xxx F / xxx C

Total hours that xture has

been powered on. Non­resettable.

Hours that xture has been

powered on since last reset.

All time max temp, non-

resettable.

TempRest.

Yes / No

CONTINUED ON NEXT PAGE

Passcode = 050 Reset LED temp.

14

Red

SYSTEM MENU

INFO (contin­ued)

DMX Values

Green

...

AutoProg

SoftVers x.xx

Displays current DMX values
for each DMX channel.

Displays current software
version.

15

DMX SETUP

DMX-512: DMX is short for Digital Multiplex. This is a universal protocol used as a form of commu­nication between intelligent fixtures and controllers. A DMX controller sends DMX data instructions
from the controller to the fixture. DMX data is sent as serial data that travels from fixture to fixture
via the DATA “IN” and DATA “OUT” XLR terminals located on all DMX fixtures (most controllers only
have a DATA “OUT” terminal).

DMX Linking: DMX is a language allowing all makes and models of different manufacturers to be

linked together and operate from a single controller, as long as all xtures and the controller are DMX

compliant. To ensure proper DMX data transmission, try to use the shortest cable path possible

when using several DMX fixtures. The order in which fixtures are connected in a DMX line does not
influence the DMX addressing. For example, a fixture assigned a DMX address of 1 may be placed
anywhere in a DMX line: at the beginning, at the end, or anywhere in the middle. When a fixture is

assigned a DMX address of 1, the DMX controller knows to send DATA assigned to address 1 to that
unit, no matter where it is located in the DMX chain.

Data Cable (DMX Cable) Requirements (For DMX Operation):The Encore LP12IP can be con­trolled via DMX-512 protocol, and features multiple DMX channel modes. Your unit and your DMX
controller require a 5-pin XLR connector for data input and data output. If you are making your own
cables, be sure to use standard 110-120 Ohm shielded cable (This cable may be purchased at
almost all pro lighting stores). Your cables should be made with a male XLR connector at one end
and a female XLR connector on the other. Also remember that DMX cable must be daisy chained
and cannot be split.

Special Note: Line Termination. When longer runs of cable are used, you may need to use a ter­minator on the last unit to avoid erratic behavior. A terminator is a 110-120 ohm 1/4 watt resistor
which is connected between pins 2 and 3 of a male XLR connector (DATA + and DATA -). This unit is
inserted in the female XLR connector of the last unit in your daisy chain to terminate the line. Using a
cable terminator (ADJ part number Z-DMX/T) will decrease the chances of erratic behavior.

16

DMX SETUP

DMX ADDRESSING

All fixtures should be given a DMX starting address when operating with a DMX controller, in order to
ensure that the correct fixture responds to the correct control signal. This digital starting address is
the channel number from which the fixture starts to “listen” to the digital control signal sent out from

the DMX controller. The assignment of this starting DMX address is achieved by setting the correct

DMX address on the digital control display on the fixture.

You can set the same starting address for all fixtures or a group of fixtures, or set different addresses
for each individual fixture. Setting all fixtures to the same DMX address will cause all fixtures to react

in the same way. In this case, please note that changing the settings of one channel will affect all the

fixtures simultaneously.

If you set each fixture to a different DMX address, each unit will start to “listen” to the channel num­ber you have set, based on the quantity of DMX channels of each fixture. That means changing the
settings of one channel will only affect the selected fixture.

As an example, when operating this device in 4 channel mode, you should set the starting DMX

address of the first unit to 1, the second unit to 5 (1 + 4), the third unit to 9 (1 + 4 + 4), and so on.
(See the chart below for more details.)

Channel Mode Unit 1 Address Unit 2 Address Unit 3 Address Unit 4 Address

4 Channels

7 Channels

8 Channels

10 Channels

13 Channels

16 Channels

1 5 9 13

1 8 15 22

1 9 17 25

1 11 21 31

1 14 27 40

1 17 33 49

DMX TRAITS

CHANNEL

4CH 7CH 8CH 10CH 13CH 16CH

1 1 1 1 1 1 000 - 255

2 000 - 255

2 2 3 2 2 2 000 - 255

4 000 - 255

3 3 5 3 3 3 000 - 255

6 000 - 255

4 4 7 4 4 4 000 - 255

8 000 - 255

5 5 5 000 - 255

6 6 6 000 - 255

7 7 7

DMX VALUE FUNCTION

000 O

001 - 054 2700K

055 - 109 3200K

Red, 0% - 100%

Red Fine

Green, 0% - 100%

Green Fine

Blue, 0% - 100%

Blue Fine

Lime, 0% - 100%

Lime Fine

Color Macros, see Color Macros Chart section for de-

tailed information

Color Temperature, 2700K - 7000K Linear

Color Temperature Macros

110 - 164 4000K

165 - 219 5600K

220 - 255 6500K

000 - 031 LEDs O

032 - 063 LEDs On

064 - 095 Strobe eect, slow to fast

5 8 8 8

6 9 9 9 000 - 255

7 10 10 10 000 - 255

11

096 - 127 LEDs On

128 - 159 Pulse-eect in sequences

160 - 191 LEDs On

192 - 223 Random strobe eect, slow to fast

224 - 255 LEDs On

000 - 031 O

032 - 063 Auto Program 1

064 - 095 Auto Program 2

Shutter, Strobe

Dimmer Intensity, 0% - 100%

Dimmer Fine

Auto Programs

096 - 127 Auto Program 3

128 - 159 Auto Program 4

CONTINUED ON NEXT PAGE

18

DMX TRAITS

CHANNEL

4CH 7CH 8CH 10CH 13CH 16CH

11

12 000 - 255

13 000 - 255

DMX VALUE FUNCTION

Auto Programs (continued)

160 - 191 Auto Program 5

192 - 223 Auto Program 6

224 - 255 Auto Program 7

Auto Program Speed, slow to fast

Auto Program Fade, least to most

Dim Mode

000 - 020 Standard

021 - 040 Stage

041 - 060 TV

061 - 080 Architectural

081 - 100 Theatre

101 - 120 Stage 2

121 0.1s dim speed

122 0.2s dim speed

11 14

123 0.3s dim speed

124 0.4s dim speed

125 0.5s dim speed

126 0.6s dim speed

127 0.7s dim speed

128 0.8s dim speed

129 0.9s dim speed

130 1.0s dim speed

131 1.5s dim speed

132 2.0s dim speed

133 3.0s dim speed

134 4.0s dim speed

135 5.0s dim speed

136 6.0s dim speed

137 7.0s dim speed

138 8.0s dim speed

139 9.0s dim speed

140 10.0s dim speed

141 - 255 Default to Unit Setting

CONTINUED ON NEXT PAGE

19

DMX TRAITS

CHANNEL

4CH 7CH 8CH 10CH 13CH 16CH

12 15

13 16

DMX VALUE FUNCTION

Dim Curves

000 - 020 Linear

021 - 040 Square

041 - 060 Inv. Squa

061 - 080 S. Curve

081 - 255 No function

Refresh Rate

000 - 015 Default to Unit Setting

016 - 030 900 Hz

031 - 045 1000 Hz

046 - 060 1100 Hz

061 - 075 1200 Hz

076 - 090 1300 Hz

091 - 105 1400 Hz

106 - 120 1500 Hz

121 - 135 2500 Hz

136 - 150 4000 Hz

151 - 165 5000 Hz

166 - 180 10000 Hz

181 - 195 15000 Hz

196 - 210 20000 Hz

211 - 225 25000 Hz

226 - 255 No Function

20

COLOR MACROS CHART

COLOR

MACRO NO.

O 000 0 0 0 0

1 001 - 004 80 255 234 80

2 005 - 008 80 255 164 80

3 009 - 012 77 255 112 77

4 013 - 016 117 255 83 83

5 017 - 020 160 255 77 77

6 021 - 024 223 255 83 83

7 025 - 028 255 243 77 77

8 029 - 032 255 200 74 74

9 033 - 036 255 166 77 77

10 037 - 040 255 125 74 74

11 041 - 044 255 97 77 71

12 045 - 048 255 71 77 71

13 049 - 052 255 83 134 83

14 053 - 056 255 93 182 93

DMX VALUE RED GREEN BLUE LIME

15 057 - 060 255 96 236 96

16 061 - 064 238 93 255 93

17 065 - 068 196 87 255 87

18 069 - 072 150 90 255 90

19 073 - 076 100 77 255 77

20 077 - 080 77 100 255 77

21 081 - 084 67 148 255 67

22 085 - 088 77 195 255 77

23 089 - 092 77 234 255 77

24 093 - 096 158 255 144 144

25 097 - 100 255 251 153 153

26 101 - 104 255 175 147 147

27 105 - 108 255 138 186 138

28 109 - 112 255 147 251 147

29 113 - 116 151 138 255 138

30 117 - 120 99 0 255 100

31 121 - 124 138 169 255 138

32 125 - 128 255 255 255 255

33 129 - 132 255 206 143 0

34 133 - 136 254 177 153 0

35 137 - 140 254 192 138 0

36 141 - 144 254 165 98 0

21

COLOR MACROS CHART

COLOR

MACRO NO.

37 145 - 148 254 121 0 0

38 149 - 152 176 17 0 0

39 153 - 156 96 0 11 0

40 157 - 160 234 139 171 0

41 161 - 164 224 5 97 0

42 165 - 168 175 77 173 0

43 169 - 172 119 130 199 0

44 173 - 176 147 164 212 0

45 177 - 180 88 2 163 0

46 181 - 184 0 38 86 0

47 185 - 188 0 142 208 0

48 189 - 192 52 148 209 0

49 193 - 196 1 134 201 0

50 197 - 200 0 145 212 0

51 201 - 204 0 121 192 0

DMX VALUE RED GREEN BLUE LIME

52 205 - 208 0 129 184 0

53 209 - 212 0 83 115 0

54 213 - 216 0 97 166 0

55 217 - 220 1 100 167 0

56 221 - 224 0 40 86 0

57 225 - 228 209 219 182 0

58 229 - 232 42 165 85 0

59 233 - 236 0 46 35 0

60 237 - 240 8 107 222 0

61 241 - 244 255 0 0 0

62 245 - 248 0 255 0 0

63 249 - 252 0 0 255 0

64 253 - 255 0 0 0 255

22

DIM MODES

23

DAISY CHAIN POWER LINKING

These units have the capability to be daisy chained together via the power in/out ports. The maxi­mum number of units that can be linked together in this manner is as follows:

• 6 units maximum when running on 120V power.

• 12 units maximum when running on 240V power.

DO NOT EXCEED THE NUMBER OF UNITS LISTED ABOVE.

DO NOT MIX MAKE AND MODEL TYPES WHEN DAISY CHAINING! All units that are connected in

this manner must be of the same make and model type.

CLEANING AND MAINTENANCE

DISCONNECT POWER BEFORE PERFORMING ANY MAINTENANCE!

CLEANING

Frequent cleaning is recommended to ensure proper function, optimized light output, and an
extended life. The frequency of cleaning depends on the environment in which the xture oper­ates: damp, smoky, or particularly dirty environments can cause greater accumulation of dirt on

the xture’s optics. Clean the external lens surface periodically with a soft cloth to avoid dirt/debris

accumulation.

NEVER use alcohol, solvents, or ammonia-based cleaners.

MAINTENANCE

Regular inspections are recommended to ensure proper function and extended life. There are no
user serviceable parts inside this xture. Please refer all other service issues to an authorized ADJ

service technician. Should you need any spare parts, please order genuine parts from your local ADJ
dealer.

Please refer to the following points during routine inspections:

• A detailed electrical check by an approved electrical engineer every three months, to make sure
the circuit contacts are in good condition and prevent overheating.

• Be sure all screws and fasteners are securely tightened at all times. Loose screws may fall out
during normal operation, resulting in damage or injury as larger parts could fall.

• Check for any deformations on the housing, color lenses, rigging hardware, and rigging points
(ceiling, suspension, trussing). Deformations in the housing could allow for dust or liquids to enter

into the xture. Damaged rigging points or unsecured rigging could cause the xture to fall and

seriously injure a person(s).

• Electric power supply cables must not show any damage, material fatigue, or sediments.

• NEVER remove the ground prong from the power cable.

DIMENSIONAL DRAWINGS

Dimensions may not be drawn to scale.

25

SPECIFICATIONS

SOURCE:

• Light Source: 12 x 20-Watt Quad RGBL LEDs (4-IN-1: Red, Green, Blue & Lime)

PHOTMETRIC DATA:

• Beam angle: 10-degree

• CRI: 84.4

• CRI R9: 67.9

• Lumens: 4700

EFFECTS:

• Linear Color Temperature Control (2700K to 7000K)

• Preset Color Temperatures (2700K, 3200K, 4000K, 5600K and 6500K)

• 16-Bit Fine Color Control (Red, Green, Blue & Lime)

• 64 built-in Color Macros

CONTROL / CONNECTIONS:

• 4-button, DMX digital display on rear panel

• 5 Operational modes: Static Color Mode, RGBL Dimmer Mode, Program Mode, and DMX Controlled

• Supports RDM (Remote Devise Management)

• With Wired Digital Communication Network

• 6 selectable Dimming Modes (Standard, Stage, TV, Architectural, Theatre & Stage 2)

• 4 selectable Dim Curves (Linear, Square Inv. Squa, S-Curve)

• Adjustable Refresh Rate (14 presets from 900 – 25,000Hz)

• Flicker Free operation (No flickering on camera)

• LED pulse and strobe effect

• Electronic Dimming: 0 - 100%

• 6 DMX Modes: 4, 7, 8, 10, 13, & 16-channel

• Quiet fan mode

CONSTRUCTION:

• IP65 Rated: Ingress Protection against liquid, snow, dust and sand

• All metal construction

• IP Rated rubber covers protect In/Out Locking Power connectors and IP rated 5-pin sockets

• Locking, outdoor IN/Out Power connectors

• Data linkable via 5-pin DMX connections

• Includes Lens kit with 4 different beam angles

• Scissor Yoke & safety eye

ELECTRICAL / THERMAL:

• Multi-voltage operation: AC 100-240V, 47/63Hz

• Daisy chain: 6 @ 120V, 12 @ 220V

• Max power: 192W

DIMENSIONS / WEIGHT:

• Dimensions (LxWxH): 11.1” x 7.9” x 11.8” / 281.2mm x 199.5mm x 300.0mm

• Weight: 10.5 lbs. / 4.75 kg.

APPROVALS / RATINGS:

• cETLus Pending

• IP65

Specifications and manual are subject to improvement without prior written notice.

26

ACCESSORY AND ORDERING INFORMATION

SKU NUMBER DESCRIPTION

ENC341 ADJ Encore LP12IP

ELP12L100 100-degree Frost Filter

ELP12L60 60-degree Frost Filter

ELP12L20 20-degree Frost Filter

ELP12L30X60 30x60-degree Frost Filter

ELP12L1X40 1x40-degree Frost Filter

27