ADJ ECO UV BAR DMX User Instructions

ECO UV BAR DMX

©2013 ADJ Products, LLC all rights reserved. Information,

specications, diagrams, images, and instructions herein are
subject to change without notice. ADJ Products, LLC logo and
identifying product names and numbers herein are trademarks
of ADJ Products, LLC. Copyright protection claimed includes all
forms and matters of copyrightable materials and information
now allowed by statutory or judicial law or hereinafter granted.
Product names used in this document may be trademarks or
registered trademarks of their respective companies and are
hereby acknowledged. All non-ADJ Products, LLC brands and
product names are trademarks or registered trademarks of their

respective companies.

ADJ Products, LLC and all afliated companies hereby dis­claim any and all liabilities for property, equipment, building, and
electrical damages, injuries to any persons, and direct or indi­rect economic loss associated with the use or reliance of any
information contained within this document, and/or as a result
of the improper, unsafe, unsufcient and negligent assembly,
installation, rigging, and operation of this product.

9/13

User Instructions

Eco UV Bar DMX Introduction

Eco UV Bar DMX General Instructions

Unpacking: Thank you for purchasing the Eco UV Bar DMX by ADJ

Products, LLC. Every Eco UV Bar DMX has been thoroughly tested
and has been shipped in perfect operating condition. Carefully check
the shipping carton for damage that may have occurred during ship­ping. If the carton appears to be damaged, carefully inspect your x­ture for any damage and be sure all accessories necessary to operate
the unit has arrived intact. In the case damage has been found or parts
are missing, please contact our toll free customer support number for
further instructions. Do not return this unit to your dealer without rst
contacting customer support.

Introduction: The Eco UV Bar DMX is part of ADJ’s continuing pur-

suit for creating high quality affordable fixtures. The Eco UV Bar DMX is
now DMX controllable, it also comes with an IR Remote for easy con­trol. This unit is great for clubs, bands, roller rinks, arenas, performance
stages, theatrical productions, and any other special effects lighting

Customer Support: ADJ Products, LLC provides a toll free cus-

tomer support line, to provide set up help and to answer any question
should you encounter problems during your set up or initial operation.
You may also visit us on the web at www.adj.com for any comments
or suggestions. Service Hours are Monday through Friday 8:00 a.m. to
4:30 p.m. Pacic Standard Time.
Voice: [phone]
Fax: [phone]
E-mail: [e-mail]
To purchase parts online visit http://parts.americandj.com

Warning! To prevent or reduce the risk of electrical shock or re, do

not expose this unit to rain or moisture.

To optimize the performance of this product, please read these operat­ing instructions carefully to familiarize yourself with the basic operations
of this unit. These instructions contain important safety information
regarding the use and maintenance of this unit. Please keep this manual
with the unit, for future reference.

Eco UV Bar DMX Warranty Registration

The Eco UV Bar DMX carries a 3 year (1095 days) limited warranty.
Please fill out the enclosed warranty card to validate your purchase
and warranty. You may also register your product online at www.
americandj.com. All returned service items whether under warranty or
not, must be freight pre-paid and accompany a return authorization
(R.A.) number. If the unit is under warranty you must provide a copy
of your proof of purchase invoice. Please contact ADJ customer sup­port for a R.A. number.

Eco UV Bar DMX Cleaning

Due to fog residue, smoke, and dust cleaning the internal and exter­nal optical lenses must be carried out periodically to optimize light
output.

1. Use normal glass cleaner and a soft cloth to wipe down the
outside casing.

2. Clean the external optics with glass cleaner and a soft cloth
every 20 days.

3. Always be sure to dry all parts completely before plugging
the unit back in.
Cleaning frequency depends on the environment in which the fixture
operates (i.e. smoke, fog residue, dust, dew).

Caution! There are no user serviceable parts inside this unit. Do not

attempt any repairs yourself, doing so will void your manufactures war­ranty. In the unlikely event your unit may require service please contact
ADJ Products, LLC.

PLEASE recycle the shipping carton when ever possible.

ADJ Products, LLC - www.adj.com - Eco UV Bar DMX User Manual Page 2

ADJ Products, LLC - www.adj.com - Eco UV Bar DMX User Manual Page 3

Eco UV Bar DMX Safety Precautions

Eco UV Bar DMX DMX Set Up

• To reduce the risk of electrical shock or re, do not expose this unit
rain or moisture

• Do not spill water or other liquids into or on to your unit.

• Be sure that the local power outlet match that of the required volt­ age for your unit.

• Do not attempt to operate this unit if the power cord has been
frayed or broken. Do not attempt to remove or break off the ground
prong from the electrical cord. This prong is used to reduce the risk
of electrical shock and re in case of an internal short.

• Disconnect from main power before making any type of connection.

• Do not remove the cover under any conditions. There are no user
serviceable parts inside.

• Never operate this unit when it’s cover is removed.

• Never plug this unit in to a dimmer pack

• Always be sure to mount this unit in an area that will allow proper
ventilation. Allow about 6” (15cm) between this device and a wall.

• Do not attempt to operate this unit, if it becomes damaged.

• This unit is intended for indoor use only, use of this product out`
doors voids all warranties.

• During long periods of non-use, disconnect the unit’s main power.

• Always mount this unit in safe and stable matter.

• Power-supply cords should be routed so that they are not likely to
be walked on or pinched by items placed upon or against them,
paying particular attention to the point they exit from the unit.

• Cleaning -The fixture should be cleaned only as recommended by
t he manufacturer. See page 3 for cleaning details.

• Heat -The appliance should be situated away from heat sources
such as radiators, heat registers, stoves, or other appliances (inclu­ d ing amplifiers) that produce heat.

• The fixture should be serviced by qualified service personnel when:
A. The power-supply cord or the plug has been damaged.
B. Objects have fallen, or liquid has been spilled into the appliance.
C. The appliance has been exposed to rain or water.
D. The appliance does not appear to operate normally or exhibits a
marked change in performance.

Power Supply: The ADJ Eco UV Bar DMX contains a automatic volt-

age switch, which will auto sense the voltage when it is plugged into
a power source. With this switch there is no need to worry about the
correct power voltage, this unit can be plugged in anywhere.

DMX-512: DMX is short for Digital Multiplex. This is a universal pro-

tocol used as a form of communication between intelligent fixtures
and controllers. A DMX controller sends DMX data instructions from
the controller to the fixture. DMX data is sent as serial data that trav­els from fixture to fixture via the DATA “IN” and DATA “OUT” XLR ter­minals located on all DMX fixtures (most controllers only have a DATA
“OUT” terminal).

DMX Linking: DMX is a language allowing all makes and models of
different manufactures to be linked together and operate from a single
controller, as long as all xtures and the controller are DMX compli­ant. To ensure proper DMX data transmission, when using several
DMX fixtures try to use the shortest cable path possible. The order
in which fixtures are connected in a DMX line does not influence the
DMX addressing. For example; a fixture assigned a DMX address of 1
may be placed anywhere in a DMX line, at the beginning, at the end,
or anywhere in the middle. When a fixture is assigned a DMX address
of 1, the DMX controller knows to send DATA assigned to address 1
to that unit, no matter where it is located in the DMX chain.

Data Cable (DMX Cable) Requirements (For DMX Operation):

The Inno Color Beam Z19 can be controlled via DMX-512 protocol. The
Eco UV Bar DMX is a 3 Channel DMX unit. The DMX address is set on
the rear panel of the Eco UV Bar DMX. Your unit and your DMX control­ler require a approved DMX-512 110 Ohm Data cable for data input
and data output (Figure 1). We recommend Accu-Cable DMX cables. If
you are making your own cables, be sure to use
standard 110-120 Ohm shielded cable (This cable
may be purchased at almost all professional
sound and lighting stores). Your cables should be
made with a male and female XLR connector on
either end of the cable. Also remember that DMX
cable must be daisy chained and cannot be split.

ADJ Products, LLC - www.adj.com - Eco UV Bar DMX User Manual Page 4

Figure 1

ADJ Products, LLC - www.adj.com - Eco UV Bar DMX User Manual Page 5

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

DMX512

DMX+,DMX-,COMMON

1

2

3

Termination reduces signal errors and
avoids signal transmission problems
and interference. It is always advisable
to connect a DMX terminal, (Resistance
120 Ohm 1/4 W) between PIN 2 (DMX-)
and PIN 3 (DMX +) of the last fixture.

POWER

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

and PIN 3 (DMX +) of the last fixture.

Eco UV Bar DMX DMX Set Up Eco UV Bar DMX Operating Instructions

Notice: Be sure to follow gures two and three when making your own

cables. Do not use the ground lug on the XLR connector. Do not con­nect the cable’s shield conductor to the ground lug or allow the shield
conductor to come in contact with the XLR’s outer casing. Grounding
the shield could cause a short circuit and erratic behavior.

1

2

XLR Male Socket

1 Ground

Figure 3

DMX512 OUT

3-PIN XLR

2 Cold

3 Hot

Special Note: Line Termination.

used, you may need to use a terminator on the last unit to avoid erratic
behavior. A terminator is a 90-120 ohm 1/4 watt resistor which is con­nected between pins 2 and 3 of a male XLR connector (DATA + and
DATA -). This unit is inserted in the female XLR connector of the last
unit in your daisy chain to terminate the line. Using a cable terminator
(ADJ part number Z-DMX/T) will decrease the possibilities of erratic
behavior.

Termination reduces signal errors and

1

avoids signal transmission problems

3

and interference. It is always advisable

2

to connect a DMX terminal, (Resistance
120 Ohm 1/4 W) between PIN 2 (DMX-)

5-Pin XLR DMX Connectors.

connectors for DATA transmission in place of 3-pin. 5-pin XLR xtures
may be implemented in a 3-pin XLR DMX line. When inserting standard
5-pin XLR connectors in to a 3-pin line a cable adaptor must be used,
these adaptors are readily available at most electric stores. The chart
below details a proper cable conversion.

3-Pin XLR to 5-Pin XLR Conversion

Conductor 5-Pin XLR Male (In)3-Pin XLR Female (Out)

Ground/Shield

Data Compliment (- signal)

Data True (+ signal)

Not Used

Not Used

3

XLR Female Socket

2 Cold

COMMON

DMX +

DMX -

3

1

2

DMX512 IN

3-PIN XLR

Figure 2

XLR Pin Conguration

1 Ground

3 Hot

Pin 1 = Ground

Pin 2 = Data Compliment (negative)

Pin 3 = Data True (positive)

When longer runs of cable are

Figure 4

Some manufactures use 5-pin XLR

Pin 1

Pin 2

Pin 3

Pin 1

Pin 2

Pin 3

Do Not Use

Do Not Use

LED Display On/Off:

To set the LED display to turn off after 10 seconds, press the MODE but­ton until “dS-x” is displayed. “X” represents either “1” or “2”. Press the
UP or DOWN buttons so that “dS-2” is displayed. Now the display will
disappear after 10s. Press any button to turn the display on again. Be
advised though that the display will turn off automatically after 10 sec-

onds.

“dS-1” = LED display on at all times.
“dS-2” = LED display shuts off after 10 seconds.

DMX Mode:

Operating through a DMX controller gives the user the freedom to create
their own programs tailored to their own individual needs. The Eco UV

Bar DMX has 3 DMX Channels.

1. This function will allow you to control each individual fixture’s traits
with a standard DMX 512 controller.

2. To run your fixture in DMX mode press the MODE button until
“1XXX” is displayed. “XXX” represents the current displayed ad­ dress. Use the UP or DOWN buttons to select your desired DMX

address.

3. Please see page 9 for the DMX values and traits.

4. After you have set your desired DMX address plug in the fixture via

the XLR connections to any standard DMX controller.

Strobe Mode:

1. Plug the fixture in and press the MODE button until “2-XX” is dis­ played. “XX” represents a number between 1-20.

2. The strobe speed can be adjusted between 1 (slowest) to 20 (fastest).

3. Use the UP and DOWN buttons to adjust the speed to your desire.

Output Intensity:

1. Plug the fixture in and press the MODE button until “UXXX” is dis­ played. “XXX” represents a number between 000-255.

2. The output intensity can be adjusted between 000 (off) to 255 (bright­ est).

3. Use the UP and DOWN buttons to adjust the output intensity to your

desire.

Delay:

1. Plug the fixture in and press the MODE button until “dr-X” is dis­ played. “X” represents a number between 0-4.

ADJ Products, LLC - www.adj.com - Eco UV Bar DMX User Manual Page 7ADJ Products, LLC - www.adj.com - Eco UV Bar DMX User Manual Page 6

Eco UV Bar DMX Operating Instructions

2. The output intensity can be adjusted between 000 (off) to 255 (bright­ est).

3. Use the UP and DOWN buttons to adjust the output intensity to your

desire.

Note: The delay mode works in conjunction with Channel 3 values 101-

255.

Eco UV Bar DMX DMX Control

Universal DMX Control: This function allows you to use a Elation®

universal DMX-512 controller to control the chases and patterns, dim­mer and strobe. A DMX controller allows you to create unique pro­grams tailored to your individual needs. The Eco UV Bar DMX has 3
DMX Channels.

1. This function will allow you to control each individual fixture’s
traits with a standard DMX 512 controller such as the
Elation® Show Designer™ or the Elation® DMX Operator.

2. To run your fixture in DMX mode, set your desired DMX address
following the directions on page 7, and the set-up specifications
that come with your DMX controller.

3. Plug in the fixture via the XLR connections to any standard DMX

controller.

4. For longer cable runs (more than a 100 feet) use a terminator on
the last fixture.

Eco UV Bar DMX IR Remote

IR Remote: The included IR remote is a basic remote control that can

control strobing and strobing speed. Each press of the Strobing but­ton will change the speed. The strobing speed goes from full on, to
slowest strobing, then moderate strobing and finally fastest strobe.
Pressing the On/Off button will allow the remote to control the Eco UV
Bar DMX.

Eco UV Bar DMX 3 DMX Channels

Channel Value Function

1 DIMMER

0 - 255 0% - 100%
2 STROBING
0 - 255 SLOW - FAST
3 DIMMER CURVE
0 - 20 NO DIMMER CURVE
21 - 40 DIMMER CURVE 1
41 - 60 DIMMER CURVE 2
61 - 80 DIMMER CURVE 3
81 - 100 DIMMER CURVE 4
101 - 255 DELAY MODE CONTROL

Channel 3 values 101-255 works in conjuction with Delay mode in the menu setting.

Eco UV Bar DMX Power Cord Daisy Chain

With this feature you can connect the xtures to one another

using the IEC input and output sockets. The quantity that can be

connected is 10 xtures maximum. After 10 xtures you will need
to use a new power outlet. They must be the same xtures. DO
NOT mix xtures.

Eco UV Bar DMX Cleaning

Master-Slave Operation: This function will allow you to link up to 16

units together and operate without a controller. The units will be sound
activated. In Master-Slave operation one unit will act as the controlling

unit and the others will react to the controlling units programs. Any unit
can act as a Master or as a Slave.

1. Using approved DMX data cables, daisy chain your units togeth-
er via the XLR connector on the rear of the units. Remember the
Male XLR connector is the input and the Female XLR connector
is the output. The rst unit in the chain (master) will use the female
XLR connector only - The last unit in the chain will use the male
XLR connector only. For longer cable runs we suggest a termina­ tor at the last fixture.

2. On the Master unit set your desired settings.

3. Set the Slave units to DMX mode setting. The Slave units should
now follow the Master.

ADJ Products, LLC - www.adj.com - Eco UV Bar DMX User Manual Page 9ADJ Products, LLC - www.adj.com - Eco UV Bar DMX User Manual Page 8

Eco UV Bar DMX Warranty

MANUFACTURER’S LIMITED WARRANTY

A. ADJ Products, LLC hereby warrants, to the original purchaser, ADJ Products, LLC products
to be free of manufacturing defects in material and workmanship for a prescribed period from
the date of purchase (see specific warranty period on reverse). This warranty shall be valid only if the
product is purchased within the United States of America, including possessions and
territories. It is the owner’s responsibility to establish the date and place of purchase by acceptable
evidence, at the time service is sought.

B. For warranty service you must obtain a Return Authorization number (RA#) before sending back the
product–please contact ADJ Products, LLC Service Department at 800-322-6337. Send the product
only to the ADJ Products, LLC factory. All shipping charges must be pre-paid. If the requested repairs or
service (including parts replacement) are within the terms of this warranty, ADJ Products, LLC will pay
return shipping charges only to a designated point within the United States. If the entire instrument is
sent, it must be shipped in it’s original package. No accessories should be shipped with the product. If
any accessories are shipped with the product, ADJ Products, LLC shall have no liability whatsoever for
loss of or damage to any such accessories, nor for the safe return thereof.

C. This warranty is void if the serial number has been altered or removed; if the product is modified in any
manner which ADJ Products, LLC concludes, after inspection, affects the reliability of the product; if the
product has been repaired or serviced by anyone other than the ADJ Products, LLC factory unless prior
written authorization was issued to purchaser by ADJ Products, LLC; if the product is damaged because
not properly maintained as set forth in the instruction manual.

D. This is not a service contract, and this warranty does not include maintnance, cleaning or periodic check
up. During the period specified above, ADJ Products, LLC will replace defective parts at its expense
with new or refurbished parts, and will absorb all expenses for warranty service and repair labor by
reason of defects in material or workmanship. The sole responsibility of ADJ Products, LLC under this
warranty shall be limited to the repair of the product, or replacement thereof, including parts, at the sole
discretion of ADJ Products, LLC. All products covered by this warranty were manufactured after August
15, 2012, and bear indentifying marks to that effect.

E. ADJ Products, LLC reserves the right to make changes in design and/or improvements upon its products
without any obligation to include these changes in any products theretofore manufactured.

No warranty, whether expressed or implied, is given or made with respect to any accessory supplied with
products described above. Except to the extent prohibited by applicable law, all implied warranties made
by ADJ Products, LLC in connection with this product, including warranties of merchantability or fitness,
are limited in duration to the warranty period set forth above. And no warranties, whether expressed or
implied, including warranties of merchantability or fitness, shall apply to this product after said period
has expired. The consumer’s and/or Dealer’s sole remedy shall be such repair or replacement as is
expressly provided above; and under no circumstances shall ADJ Products, LLC be liable for any loss or
damage, direct or consequential, arising out of the use of, or inability to use, this product.

This warranty is the only written warranty applicable to ADJ Products, LLC Products and
supersedes all prior warranties and written descriptions of warranty terms and conditions heretofore
published.

MANUFACTURER’S LIMITED WARRANTY PERIODS:

 •LightingProducts=1-year(365days)LimitedWarranty(Such as: Special Effect Lighting, Intelligent

Lighting, UV lighting, Strobes, Fog Machines, Bubble Machines, Mirror Balls, Par Cans, Trussing,
Lighting Stands etc. excluding LEDs and lamps)

 •LaserProducts=90-DayLimitedWarranty
 •L.E.D.Products=3-year(1095days)LimitedWarranty(excluding motors, PCB boards, and power

supplies, which have a 1-year (365 day Limited Warranty) and batteries which have a 180 day
limited warranty). Only the L.E.D.s carry a 3-year warranty

ADJ Products, LLC - www.adj.com - Eco UV Bar DMX User Manual Page 10

Eco UV Bar DMX Specifications

Model:

SPECIFICATIONS:

Eco UV Bar DMX

Working Position: Any safe working position
Voltage: 100V ~ 240V, 47/63Hz
Power Cord Daisy Chain: 10 Fixtures Max.
LEDs: 18 x 3W LEDs
Beam Angle: 120 Degrees
Power Consumption: 52W
Fuse: 1Amp
Weight: 5lbs./ 2.3Kgs.
Dimensions: 39.5” (L) x 2.5” (W) x 4.75” (H)
1000 (L) x 60 (W) x 115 (H) mm
Colors: UV
Warranty: 3 Year (1095 days)

Auto Sensing Voltage: This xture contains a electronic bal-

last, which will auto sense the voltage when it is plugged into the
power source.

Please Note: Specications and improvements in the design of
this unit and this manual are subject to change without any prior
written notice.

ADJ Products, LLC

6122 S. Eastern Ave. Los Angeles, CA 90040 USA

Tel: [phone] / Fax: [phone]

Web: www.adj.com / E-mail: [e-mail]

A.D.J. Supply Europe B.V.

Junostraat 2

6468 EW Kerkrade

Netherlands

[e-mail] / www.adj.eu

Tel: [phone] / Fax: [phone]