Adj Double Phase LED User Manual [ru]

Double Phase LED General Information

Unpacking: Thank you for purchasing the Double Phase LED by

American DJ®. Every Double Phase LED has been thoroughly tested
and has been shipped in perfect operating condition. Carefully check
the shipping carton for damage that may have occurred during ship­ping. If the carton appears to be damaged, carefully inspect your x­ture for any damage and be sure all equipment necessary to operate
the unit has arrived intact. In the event damage has been found or parts
are missing, please contact our toll free customer support number for
further instructions. Please do not return this unit to your dealer with-

out contacting customer support rst.

Introduction: The Double Phase LED is a dual barrel mirrored, DMX

intelligent, 4-in-1 RGBW LED fixture. The Double Phase LED is 6
Channel DMX unit. The fixture can operate in three different operating

modes; show mode, sound-active, or controlled via DMX. The unit can
be used as a stand alone unit or linked in a master/slave configuration.

For best results use fog or special effects smoke to enhance the beams
projections.

Customer Support: American DJ® provides a toll free customer

support line, to provide help and to answer any question should you
encounter problems during your set up or initial operation. You may
also visit us on the web at www.americandj.com for any comments or
suggestions. Service Hours are Monday through Friday 8:00 a.m. to

4:30 p.m. Pacic Standard Time.
Voice: [phone]
Fax: [phone]

E-mail: [e-mail]
To purchase parts online visit http://parts.americandj.com

3/12

User Instructions

Warning! To prevent or reduce the risk of electrical shock or re, do

not expose this unit to rain or moisture.

Warning! This may cause severe eye damage. Avoid looking directly

into the light source at all times!

American DJ® - www.americandj.com - Double Phase LED Instruction Manual Page 2

Double Phase LED General Instructions

Double Phase LED Safety Precautions

To optimize the performance of this product, please read these
operating instructions carefully to familiarize yourself with the basic
operations of this unit. These instructions contain important safety
information regarding the use and maintenance of this unit. Please
keep this manual with the unit, for future reference.

Double Phase LED Features

• Two DMX Channel Modes: 1 Channel Mode & 6 Channel Mode

• CREE Brand 4-in-1 RGBW LEDs

• 3 Operating Modes - Sound Active mode, Show mode, and DMX

Controlled

• Set Up: Stand Alone or Master-Slave Configuration

• Internal Microphone

• Digital Display for Address and Function Setting

• UC3 Controller (Not Included)

• 8 Preprogrammed Shows and 1 Random Show

• Power Cord Daisy Chain

Double Phase LED Warranty Registration

The Double Phase LED carries a 3 year (1095 days) limited warranty.
Please fill out the enclosed warranty card to validate your purchase
and warranty. You may also register your product online at www.
americandj.com. All returned service items whether under warranty or
not, must be freight pre-paid and accompany a return authorization
(R.A.) number. If the unit is under warranty you must provide a copy
of your proof of purchase invoice. Please contact American DJ® cus­tomer support for a R.A. number.

Double Phase LED Handling Precautions

Caution! There are no user serviceable parts inside this unit. Do not

attempt any repairs yourself, doing so will void your manufactures war­ranty. In the unlikely event your unit may require service please contact
American DJ®.

American DJ® will not accept any liability for any resulting damages
caused by the non-observance of this manual or any unauthorized

modication to this unit.

For Your Own Personal Safety, Please Read and Understand This

Manual Completely Before You Attempt To Install Or Operate

This Unit!

• To reduce the risk of electrical shock or re, do not expose this unit

rain or moisture

• Do not spill water or other liquids into or on to your unit.

• Be sure that the local power outlet match that of the required volt-

age for your unit.

• Do not attempt to operate this unit if the power cord has been

frayed or broken.

• Do not attempt to remove or break o the ground prong from

the electrical cord. This prong is used to reduce the risk of electrical

shock and re in case of an internal short.

• Disconnect from main power before making any type of connection.

• Do not remove the cover under any conditions. There are no user

serviceable parts inside.

• Never operate this unit when it’s cover is removed.

• Always be sure to mount this unit in an area that will allow proper
ventilation. Allow about 6” (15cm) between this device and a wall.

• Do not attempt to operate this unit, if it becomes damaged.

• This unit is intended for indoor use only, use of this product out-

doors voids all warranties.

• Always mount this unit in safe and stable matter.

• Power-supply cords should be routed so that they are not likely to

be walked on or pinched by items placed upon or against them,
paying particular attention to cords at plugs, convenience recep-

tacles, and the point where they exit from the appliance.

• Cleaning -The fixture should be cleaned only as recommended by

the manufacturer. See page 18 for cleaning details.

• Heat -This fixture should be situated away from heat sources such

as radiators, heat registers, stoves, or other appliances (including
amplifiers) that produce heat.

• The fixture should be serviced by qualified service personnel when:

A. Objects have fallen, or liquid has been spilled into the appliance.

B. The appliance has been exposed to rain or water.
C. The appliance does not appear to operate normally or exhibits a

marked change in performance.

American DJ® - www.americandj.com - Double Phase LED Instruction Manual Page 4American DJ® - www.americandj.com - Double Phase LED Instruction Manual Page 3

Double Phase LED Set Up

Double Phase LED Set Up

Power Supply: The American DJ® Double Phase LED contains a

automatic voltage switch, which will auto sense the voltage when it
is plugged into the power source. With this switch there is no need
to worry about the correct power voltage, this unit can be plugged in
anywhere.

DMX-512: DMX is short for Digital Multiplex. This is a universal pro-

tocol used by most lighting and controller manufactures as a form of
communication between intelligent fixtures and controllers. A DMX

controller sends DMX data instructions from the controller to the fix­ture. DMX data is sent as serial data that travels from fixture to fixture
via the DATA “IN” and DATA “OUT” XLR terminals located on all DMX
fixtures (most controllers only have a DATA “OUT” terminal).

DMX Linking: DMX is a language allowing all makes and models

of dierent manufactures to be linked together and operate from a
single controller, as long as all xtures and the controller are DMX

compliant. To ensure proper DMX data transmission, when using
several DMX fixtures try to use the shortest cable path possible. The
order in which fixtures are connected in a DMX line does not influence
the DMX addressing. For example; a fixture assigned a DMX address
of 1 may be placed anywhere in a DMX line, at the beginning, at the
end, or anywhere in the middle. Therefore, the first fixture controlled
by the controller could be the last fixture in the chain. When a fixture
is assigned a DMX address of 1, the DMX controller knows to send
DATA assigned to address 1 to that unit, no matter where it is located
in the DMX chain.

Data Cable (DMX Cable) Requirements (For DMX and Master/Slave
Operation): The Double Phase LED can be controlled via DMX-512

protocol. The Double Phase LED has 2 DMX Channel modes; a 1

Channel mode and a 6 channel mode. The DMX

address is set electronically using the controls on
the rear panel of the unit. Your unit and your DMX

controller require a approved DMX-512 110 Ohm

Data cable for data input and data output (Figure

1). We recommend Accu-Cable DMX cables. If you
are making your own cables, be sure to use stan­dard 110-120 Ohm shielded cable (This cable may
be purchased at almost all professional sound and

Figure 1

lighting stores). Your cables should be made with a male and female
XLR connector on either end of the cable. Also remember that DMX
cable must be daisy chained and cannot be split.

Notice: Be sure to follow gures two and three when making your own

cables. Do not use the ground lug on the XLR connector. Do not con-

nect the cable’s shield conductor to the ground lug or allow the shield
conductor to come in contact with the XLR’s outer casing. Grounding

the shield could cause a short circuit and erratic behavior.

COMMON

1

DMX512 IN

3

3-PIN XLR

1 Ground

2

XLR Pin Conguration

Pin 1 = Ground

Pin 2 = Data Compliment (negative)

Pin 3 = Data True (positive)

Figure 2

When longer runs of cable are

Figure 4

XLR Male Socket

1 Ground

Figure 3

DMX512 OUT

3-PIN XLR

2 Cold

3 Hot

1

3

2

DMX +

DMX -

XLR Female Socket

2 Cold

3 Hot

Special Note: Line Termination.

used, you may need to use a terminator on the last unit to avoid erratic
behavior. A terminator is a 110-120 ohm 1/4 watt resistor which is con­nected between pins 2 and 3 of a male XLR connector (DATA + and
DATA -). This unit is inserted in the female XLR connector of the last

unit in your daisy chain to terminate the line. Using a cable terminator

(ADJ part number Z-DMX/T) will decrease the possibilities of erratic
behavior.

Termination reduces signal errors and

1

avoids signal transmission problems

3

and interference. It is always advisable

2

to connect a DMX terminal, (Resistance
120 Ohm 1/4 W) between PIN 2 (DMX-)
and PIN 3 (DMX +) of the last fixture.

American DJ® - www.americandj.com - Double Phase LED Instruction Manual Page 6American DJ® - www.americandj.com - Double Phase LED Instruction Manual Page 5

Double Phase LED Set Up Double Phase LED System Menu

5-Pin XLR DMX Connectors.

Some manufactures use 5-pin DMX-

512 data cables for DATA transmission in place of 3-pin. 5-pin DMX
xtures may be implemented in a 3-pin DMX line. When inserting stan­dard 5-pin data cables in to a 3-pin line a cable adaptor must be used,

these adaptors are readily available at most electric stores. The chart
below details a proper cable conversion.

3-Pin XLR to 5-Pin XLR Conversion

Conductor 5-Pin XLR Male (In)3-Pin XLR Female (Out)

Ground/Shield

Data Compliment (- signal)

Data True (+ signal)

Not Used

Not Used

Pin 1

Pin 2

Pin 3

Pin 1

Pin 2

Pin 3

Pin 4 - Do Not Use

Pin 5 - Do Not Use

American DJ® - www.americandj.com - Double Phase LED Instruction Manual Page 7 American DJ® - www.americandj.com - Double Phase LED Instruction Manual Page 8

Double Phase LED System Menu

Double Phase LED System Menu

ADDR - DMX Address Setting.

1. Press the either the MENU, UP, or DOWN buttons until

“ADDR” is displayed, press ENTER.

2. “1” will now be displayed and ashing. Press the UP or

DOWN buttons to nd your desired address. Leave the display

on this address, and after a few seconds the address will be
saved into memory.

CHND - This will let select your desired DMX channel

mode.

1. Press the either the MENU button until “CHND” is displayed,
press ENTER. Either “1CH” or “6CH” will be displayed

2. Press the UP or DOWN buttons to nd your desired DMX
mode and press ENTER to conm and exit.

SLND - This will let you set unit as a master or slave in a

master/slave conguration.

1. Press the either the MENU button until “SLND” is displayed,
press ENTER. Either “SL 1” or “SL 2” will be displayed.

2. Press the UP or DOWN buttons until your desired setting is
displayed, press ENTER to conm and exit.

3. Press the ENTER button, to select your desired show speed.

4. Once you have selected the show speed press ENTER and
then press and hold the MENU button for at least 3 seconds to
conrm.

SOUN - In this mode you can run the unit in sound active

mode. A show must be selected before the unit will run in
sound active mode.

1. Press the MENU button until “SOUN” is displayed, press ENTER.

2. Either “ON” or “OFF” will now be displayed. Press the UP or DOWN
buttons to select one or the other.

3. When you have made your selection, press the ENTER, and then
press and hold the MENU button for at least 3 seconds to conrm.

SENS - Using this mode, you can set the sound sensitivity

level. 0 for least sensitive, 100 for most sensitive.

1. Press the MENU button until “SENS” is displayed, press ENTER.

2. Using the UP or DOWN buttons adjust the sensivity level to your

desire.

3. When you found your desired level, press the ENTER, and then press
and hold the MENU button for at least 3 seconds to conrm.

BLND - Blackout or Stand by mode.

SHND - Show modes 0-8 (Factory programs). In show mode

the unit can run with either sound activity on or off.

1. Press the MENU button until “SHND” is displayed, press ENTER.

2. “Sh X” will now be displayed, “X” representing a number
between 0-8. Programs 1-8 are factory programs, while “Sh 0”

is random mode. Press the UP or DOWN buttons to nd your

desired show.

1. Press the either the MENU button until “BLND” is displayed,
press ENTER. Either Yes or No will be displayed.

2. To activate Blackout tap the UP or DOWN buttons until Yes is
displayed, press ENTER to conm and exit. The xture will now
be in Blackout mode. To deactivate Blackout mode, select No

and press Enter.

American DJ® - www.americandj.com - Double Phase LED Instruction Manual Page 10American DJ® - www.americandj.com - Double Phase LED Instruction Manual Page 9

Double Phase LED System Menu

Double Phase LED System Menu

LED - With this function you can have the LED display

turn off after 10 seconds.

1. Tap the MENU button until “LED” is displayed, press ENTER.

2. The display will show either “ON” or “OFF”. Press the UP or

DOWN buttons to select “ON” to keep the LED display on at

all times, or “OFF” to switch to have the LED display switch o
after 10 seconds. To make the display reappear, press and hold

the MENU button for at least 5 secs.

3. Press ENTER to conrm.

DISP - This function will reverse the display 180º.

1. Press the either the MENU button until “DISP” is displayed,
press ENTER.

2. Press the UP button to select “DSIP” to “ip” the display, or
“DISP” to change the display back.

3. Press ENTER to conrm.

TEST - This function will run a self test program .

VER - Use this function to display the Software version of

the unit.

1. Press the either the MENU button until “VER” is displayed,
press ENTER.

2. The display will show the software version.

RSET - This function will reset the unit to default settings.

1. Press the MENU button until “RSET” is displayed. Press the
ENTER button and the unit will reset itself.

1. Press the MENU button until “TEST” is displayed, press ENTER.

2. The unit will now run a self test. Press the MENU button to exit.

FHRS - With this function you can display the running time

of the unit.

1. Press the either the MENU button until “FHRS” is displayed,
press ENTER.

2. The display shows the running time of the unit. Press MENU
to exit.

American DJ® - www.americandj.com - Double Phase LED Instruction Manual Page 11

American DJ® - www.americandj.com - Double Phase LED Instruction Manual Page 12

Double Phase LED Operation

Double Phase LED Operation

Operating Modes: The Double Phase LED three operating
modes.

• Sound Active Mode -

The unit will react to sound, chasing through the built-in programs.
The sound sensitivity is adjustable.

• Show Mode -
Run 1 of 8 preset shows.

• DMX control mode -
This function will allow you to control each individual fixtures traits
with a standard DMX-512 controller such as the Elation® Show
Designer.

™

Universal DMX Control: This function allows you to use a

Elation® universal DMX-512 controller to control the chases and
patterns, dimmer and strobe. A DMX controller allows you to create
unique programs tailored to your individual needs.

1. The Double Phase LED has two DMX Channel modes. A 1 chan-

nel mode and a 6 channel mode. To set the channel mode see
page 9. See pages 16-17 for detailed description of the DMX

traits.

2. To control your fixture in DMX mode, follow the set-up procedures
on pages 5-7 as well as the set-up specifications that are

included with your DMX controller.

3. Use the controller’s faders to control the various DMX fixture traits.

4. This will allow you to create your own programs.

5. Follow the instruction on page 9 to set the DMX address.

6. For longer cable runs (more than a 100 feet) use a terminator on
the last fixture.

7. For help operating in DMX mode consult the manual included

with your DMX controller.

Show Mode: In this mode you can choose 1 of 8 shows to run.

1. Tap the MENU button until “SHND” is displayed, and press
ENTER.

2. Tap the UP or DOWN buttons until you nd your desired show,
and press ENTER then press and hold MENU for 3 seconds to
con rm. See page 9 for more info.

3. The optional UC3 Controller (not included) may be used to con­ trol different functions including blackout.

Master-Slave Operation: This function will allow you to link up to 16

units together and operate without a controller. The units will be sound
activated. In Master-Slave operation one unit will act as the controlling
unit and the others will react to the controlling units programs. Any unit
can act as a Master or as a Slave.

1. Using approved DMX data cables, daisy chain your units togeth-

er via the XLR connector on the rear of the units. Remember the
Male XLR connector is the input and the Female XLR connector

is the output. The rst unit in the chain (master) will use the female

XLR connector only - The last unit in the chain will use the male
XLR connector only. For longer cable runs we suggest a termina-

tor at the last fixture.

2. On the Master unit find your desired show and set that show by

pressiing the ENTER button.

3. On the slave units tap the MENU button until “SLND” is displayed,
and Press ENTER. Choose either “SL 1” or “SL 2” and press
ENTER. See page 9 for more info.

4. The slave units will now follow the Master unit.

5. The optional UC3 Controller (not included) may be used to con-
trol different functions including blackout.

Sound Active Mode: This mode allows either single unit or several

units linked together, to run to the beat of the music.

1. Press the MENU button until “SOUN” is displayed, and press
ENTER. Press the UP or DOWN buttons so that “ON” is displayed

and press ENTER. The unit is now sound active.

See page 10 for sound sensitivity adjustment.

2. The optional UC3 Controller (not included) may be used to con-
trol different functions including blackout.

American DJ® - www.americandj.com - Double Phase LED Instruction Manual Page 13 American DJ® - www.americandj.com - Double Phase LED Instruction Manual Page 14

Double Phase LED Power Cord Daisy Chain

Double Phase LED 1 Channel DMX Mode

With this feature you can connect the xtures to one another

using the IEC input and output sockets. The quantity that can be

connected is 9 xtures maximum. After 9 xtures you will need
to use a new power outlet. They must be the same xtures. DO
NOT mix xtures.

Double Phase LED UC3 Control

Blackout Blackout the unit

Rotation Speed

1. Fast

2. Middle

3. Slow

Speed
(LED blinking)

Function

Mode

1. Synchronous Strobe

2. Two Light Strobe

3. Sound Strobe

Strobe
(LED OFF)

Select Show
(Show 1-8)

Show
(LED ON)

Channel Value Function
1 SHOW MODES

0 - 7 BLACKOUT
8 - 37 SHOW 1
38 - 67 SHOW 2
68 - 97 SHOW 3
98 - 127 SHOW 4
128 - 157 SHOW 5
158 - 187 SHOW 6
188 - 217 SHOW 7
218 - 247 SHOW 8
248 - 255 RANDOM SHOWS 1-8

Double Phase LED 6 Channel DMX Mode

Channel Value Function
1 DIMMER/STROBE (MIRROR 1)

0 - 7 OFF
8 - 199 MASTER DIMMER 0% - 100%
200 - 247 STROBING SLOW - FAST
248 - 255 FULL ON

2 COLORS (MIRROR 1)

0 - 15 BLACKOUT
16 - 31 COLOR 1
32 - 47 COLOR 2
48 - 63 COLOR 3
64 - 79 COLOR 4
80 - 95 COLOR 5
96 - 111 COLOR 6
112 - 127 COLOR 7

128 - 143 COLOR 8

144 - 159 COLOR 9
160 - 175 COLOR 10
176 - 191 COLOR 11
192 - 207 COLOR 12

208 - 223 COLOR 13

American DJ® - www.americandj.com - Double Phase LED Instruction Manual Page 15 American DJ® - www.americandj.com - Double Phase LED Instruction Manual Page 16

Double Phase LED 6 Channel DMX Mode

Double Phase LED Fuse Replacement

Channel Value Function
2 COLORS (MIRROR 1) CONT.

224 - 239 COLOR 14
240 - 255 COLOR 15
3 BARREL ROTATION (MIRROR 1)
0 -9 STOP
10 - 120 ROTATION FAST - SLOW

121 - 134 STOP

135 - 245 ROTATION SLOW - FAST
246 - 255 STOP

4 DIMMER/STROBE (MIRROR 2)

0 - 7 OFF
8 - 199 MASTER DIMMER 0% - 100%
200 - 247 STROBING SLOW - FAST
248 - 255 FULL ON
5 COLORS (MIRROR 2)
PLEASE SEE CHANNEL 2
6 BARREL ROTATION (MIRROR 2)
0 -9 STOP
10 - 120 ROTATION FAST - SLOW

121 - 134 STOP

135 - 245 ROTATION SLOW - FAST
246 - 255 STOP

Locate and remove the unit’s power cord. Once the cord has been

removed located the fuse holder located inside the power socket.
Insert a flat-head screw driver into the power socket and gently pry
out the fuse holder. Remove the bad fuse and replace with a new one.
The fuse holder has a built-in socket for a spare fuse be sure not to
confuse the spare fuse with active fuse.

Double Phase LED Cleaning

Fixture Cleaning: Due to fog residue, smoke, and dust cleaning the

internal and external optical lenses and mirror should be carried out

periodically to optimize light output. Cleaning frequency depends on

the environment in which the fixture operates (I.e. smoke, fog residue,

dust, dew). In heavy club use we recommend cleaning on a monthly
basis. Periodic cleaning will ensure longevity, and crisp output.

1. Use normal glass cleaner and a soft cloth to wipe down the out-

side casing.

2. Use a brush to wipe down the cooling vents and fan grill.

3. Clean the external optics with glass cleaner and a soft cloth every

20 days.

4. Clean the internal optics with glass cleaner and a soft cloth every

30-60 days.

5. Always be sure to dry all parts completely before plugging the unit

back in.

Double Phase LED Trouble Shooting

Trouble Shooting: Listed below are a few common problems that
you may encounter, with solutions.

No light output from the unit;

1. Be sure the external fuse has not blown. The fuse is located on
the bottom panel of the unit.

2. Be sure the fuse holder is completely and properly seated.

Unit does not respond to sound;

1. Low frequencies (bass) should cause the unit to react to sound.
Tapping on the microphone, quiet or high pitched sounds may
not activate the unit.

American DJ® - www.americandj.com - Double Phase LED Instruction Manual Page 17 American DJ® - www.americandj.com - Double Phase LED Instruction Manual Page 18

Double Phase LED Warranty

MANUFACTURER’S LIMITED WARRANTY

A. American DJ, Inc. hereby warrants, to the original purchaser, American DJ and American
Audio products to be free of manufacturing defects in material and workmanship for a prescribed

period from the date of purchase (see specic warranty period on reverse). This warranty shall be
valid only if the product is purchased within the United States of America, including possessions
and territories. It is the owner’s responsibility to establish the date and place of purchase by ac-

ceptable evidence, at the time service is sought.

B. For warranty service you must obtain a Return Authorization number (RA#) before

sending back the product. Contact American DJ, Inc. Service Department at 800-322-6337. Send

the product only to the American DJ, Inc. factory. All shipping charges must be pre-paid. If the
requested repairs or service (including parts replacement) are within the terms of this warranty,

American DJ, Inc. will pay return shipping charges only to a designated point within the United
States. If the entire instrument is sent, it must be shipped in it’s original package. No accessories

should be shipped with the product. If any accessories are shipped with the product, American DJ,
Inc. shall have no liability whatsoever for loss of or damage to any such accessories, nor for the
safe return thereof.

C. This warranty is void if the serial number has been altered or removed; if the product is

modied in any manner which American DJ, Inc. concludes, after inspection, aects the reliability

of the product; if the product has been repaired or serviced by anyone other than the American DJ,
Inc. factory unless prior written authorization was issued to purchaser by American DJ, Inc.; if the
product is damaged because not properly maintained as set forth in the instruction manual.

D. This is not a service contract, and this warranty does not include maintenance, cleaning

or periodic check-up. During the period specied above, American DJ, Inc. will replace defec­tive parts at its expense with new or refurbished parts, and will absorb all expenses for warranty

service and repair labor by reason of defects in material or workmanship. The sole responsibility
of American DJ, Inc. under this warranty shall be limited to the repair of the product, or replace­ment thereof, including parts, at the sole discretion of American DJ. All products covered by this

warranty were manufactured after January 1, 1990, and bear identifying marks to that eect.

E. American DJ, Inc. reserves the right to make changes in design and/or improvements
upon its products without any obligation to include these changes in any products theretofore

manufactured. No warranty, whether expressed or implied, is given or made with respect to any
accessory supplied with products described above. Except to the extent prohibited by applicable

law, all implied warranties made by American DJ, Inc. in connection with this product, including

warranties of merchantability or tness, are limited in duration to the warranty period set forth
above. And no warranties, whether expressed or implied, including warranties of merchantability
or tness, shall apply to this product after said period has expired. The consumer’s and/or Dealer’s
sole remedy shall be such repair or replacement as is expressly provided above; and under no

circumstances shall American DJ, Inc. be liable for any loss or damage, direct or consequential,
arising out of the use of, or inability to use, this product.

This warranty is the only written warranty applicable to American DJ and American Audio
Products and supersedes all prior warranties and written descriptions of warranty terms and
conditions heretofore published.

MANUFACTURER’S LIMITED WARRANTY PERIODS:

• All American Audio Products = 1-year (365 day) Limited Warranty (except V-Plus Series Ampli­ers)

• All American Audio V-Plus Series Ampliers = 3-year (1095 day) Limited Warranty

• American DJ Lighting and American DJ Branded Products = 1-year (365 day) Limited Warranty
(Such as: Special Eect Lighting, Intelligent Lighting, UV lighting, Strobes, Fog Machines, Bubble
Machines, Mirror Balls, Par Cans, Trussing, Lighting Stands etc. excluding Laser Products, lamps,

and Star Tec Series)

• American DJ Laser Products and Star Tec Products = 90-Day Limited Warranty

• American DJ L.E.D. Products = 3-year (1095 day) Limited Warranty (excluding motors which
have a 1-year (365 day Limited Warranty)

American DJ® - www.americandj.com - Double Phase LED Instruction Manual Page 19

Double Phase LED Specifications

Model: Double Phase LED

Voltage: 100V~240V 50/60Hz
LEDs: 2 x 10W 4-In-1 LEDs
Beam Angle: 150 Degrees
Power Consumption: 40W
Fuse: 7A
Power Cord Daisy Chain: 9 Fixtures Max.
Dimensions: 19”(L) x 7.75”(W) x 5.25”(H)

478mm x 194.5mm x 134mm

Weight: 10 Lbs. / 4.5 kgs.
Colors: RGB + White
Duty Cycle: None
DMX: 1 or 6 DMX Channels
Sound Active: Ye s
Working Position: Any Safe, Secure Position
Warranty: 3 Year (1095 days)

Auto Sensing Voltage: This xture contains a electronic bal-

last, which will auto sense the voltage when it is plugged into the
power source.

Please Note: Specications and improvements in the design

of this unit and this manual are subject to change without any
prior written notice.

©American DJ Supply

American DJ World Headquarters:

6122 S. Eastern Ave. Los Angeles, CA 90040 USA

Tel: [phone] / Fax: [phone]

Web: www.americandj.com / E-mail: [e-mail]

American DJ Europe

Junostraat 2

6468 EW Kerkrade

Netherlands

[e-mail] / www.americandj.eu

Tel: [phone] / Fax: [phone]