ADJ Dotz Panel 2.4 User guide

Dotz Panel 2.4

©2013 ADJ Products, LLC all rights reserved. Information,

specications, diagrams, images, and instructions herein are
subject to change without notice. ADJ Products, LLC logo and
identifying product names and numbers herein are trademarks
of ADJ Products, LLC. Copyright protection claimed includes all
forms and matters of copyrightable materials and information
now allowed by statutory or judicial law or hereinafter granted.
Product names used in this document may be trademarks or
registered trademarks of their respective companies and are
hereby acknowledged. All non-ADJ Products, LLC brands and
product names are trademarks or registered trademarks of their

respective companies.

ADJ Products, LLC and all aliated companies hereby dis­claim any and all liabilities for property, equipment, building, and
electrical damages, injuries to any persons, and direct or indi­rect economic loss associated with the use or reliance of any
information contained within this document, and/or as a result
of the improper, unsafe, unsucient and negligent assembly,
installation, rigging, and operation of this product.

10/13

User Instructions

Dotz Panel 2.4 Introduction

Dotz Panel 2.4 General Instructions

Unpacking: Thank you for purchasing the Dotz Panel 2.4 by ADJ

Products, LLC. Every Dotz Panel 2.4 has been thoroughly tested and
has been shipped in perfect operating condition. Carefully check the
shipping carton for damage that may have occurred during shipping.
If the carton appears to be damaged, carefully inspect your xture for
any damage and be sure all accessories necessary to operate the unit
has arrived intact. In the case damage has been found or parts are
missing, please contact our toll free customer support number for fur­ther instructions. Do not return this unit to your dealer without rst con­tacting customer support.

Introduction: The Dotz Panel 2.4 is part of ADJ’s continuing pursuit

for creating high quality affordable intelligent fixtures. The Dotz Panel

2.4 is a high performance, DMX intelligent, LED fixture. This fixture is a
great piece for retail stores, displays, mood, architectural, interior and
exterior decoration, and clubs. This unit can be used as a stand alone
unit, or in a Master/Slave conguration. The unit can also be controlled
via DMX controller. This fixture is suitable for theaters, studios, retail

stores, and other similar locations.

Customer Support: ADJ Products, LLC provides a toll free cus-

tomer support line, to provide set up help and to answer any question
should you encounter problems during your set up or initial operation.
You may also visit us on the web at www.adj.com for any comments
or suggestions. Service Hours are Monday through Friday 8:00 a.m. to
4:30 p.m. Pacic Standard Time.
Voice: [phone]
Fax: [phone]
E-mail: [e-mail]
To purchase parts online visit http://parts.americandj.com

To optimize the performance of this product, please read these operat­ing instructions carefully to familiarize yourself with the basic operations
of this unit. These instructions contain important safety information
regarding the use and maintenance of this unit. Please keep this manual
with the unit, for future reference.

Dotz Panel 2.4 Features

• RGB Color Mixing

• Strobing

• Electronic Dimming 0-100%

• Built in Microphone

• DMX-512 protocol

• Five DMX Modes: 3 Channel Mode, 6 Channel Mode, 8 Channel
Mode, 24 Channel Mode, & 29 Channel Mode

• 4 Operating Modes - Sound Active, Auto Run, Built-In Programs,
or DMX Control

• Power Cord Daisy Chaining (See Page 20)

Dotz Panel 2.4 Warranty Registration

The Dotz Panel 2.4 carries a 3 year (1095 days) limited warranty.
Please fill out the enclosed warranty card to validate your purchase
and warranty. You may also register your product online at www.
americandj.com. All returned service items whether under warranty or
not, must be freight pre-paid and accompany a return authorization
(R.A.) number. If the unit is under warranty you must provide a copy
of your proof of purchase invoice. Please contact ADJ Products, LLC
customer support for a R.A. number.

Warning! To prevent or reduce the risk of electrical shock or re, do

not expose this unit to rain or moisture.

Caution! There are no user serviceable parts inside this unit. Do not

attempt any repairs yourself, doing so will void your manufactures war­ranty. In the unlikely event your unit may require service please contact
ADJ Products, LLC.

PLEASE recycle the shipping carton when ever possible.

ADJ Products, LLC - www.adj.com - Dotz Panel 2.4 User Manual Page 2

ADJ Products, LLC - www.adj.com - Dotz Panel 2.4 User Manual Page 3

Dotz Panel 2.4 Safety Precautions

Dotz Panel 2.4 Set Up

• To reduce the risk of electrical shock or re, do not expose this unit
rain or moisture

• Do not spill water or other liquids into or on to your unit.

• Be sure that the local power outlet match that of the required volt­ age for your unit.

• Do not attempt to operate this unit if the power cord has been
frayed or broken. Do not attempt to remove or break o the ground
prong from the electrical cord. This prong is used to reduce the risk
of electrical shock and re in case of an internal short.

• Disconnect from main power before making any type of connection.

• Do not remove the cover under any conditions. There are no user
serviceable parts inside.

• Never operate this unit when it’s cover is removed.

• Never plug this unit in to a dimmer pack

• Always be sure to mount this unit in an area that will allow proper
ventilation. Allow about 6” (15cm) between this device and a wall.

• Do not attempt to operate this unit, if it becomes damaged.

• This unit is intended for indoor use only, use of this product out`
doors voids all warranties.

• During long periods of non-use, disconnect the unit’s main power.

• Always mount this unit in safe and stable matter.

• Power-supply cords should be routed so that they are not likely to
be walked on or pinched by items placed upon or against them,
paying particular attention to the point they exit from the unit.

• Cleaning -The fixture should be cleaned only as recommended by
t he manufacturer. See page 21 for cleaning details.

• Heat -The appliance should be situated away from heat sources
such as radiators, heat registers, stoves, or other appliances (inclu­ d ing amplifiers) that produce heat.

• The fixture should be serviced by qualified service personnel when:
A. The power-supply cord or the plug has been damaged.
B. Objects have fallen, or liquid has been spilled into the appliance.
C. The appliance has been exposed to rain or water.
D. The appliance does not appear to operate normally or exhibits a
marked change in performance.

ADJ Products, LLC - www.adj.com - Dotz Panel 2.4 User Manual Page 4

Power Supply: The ADJ Dotz Panel 2.4 contains a automatic volt-

age switch, which will auto sense the voltage when it is plugged into
a power source. With this switch there is no need to worry about the
correct power voltage, this unit can be plugged in anywhere. Always
use the PowerCon cord that came with the unit.

DMX-512: DMX is short for Digital Multiplex. This is a universal pro-

tocol used as a form of communication between intelligent fixtures
and controllers. A DMX controller sends DMX data instructions from
the controller to the fixture. DMX data is sent as serial data that trav­els from fixture to fixture via the DATA “IN” and DATA “OUT” XLR ter­minals located on all DMX fixtures (most controllers only have a DATA
“OUT” terminal).

DMX Linking: DMX is a language allowing all makes and models of
dierent manufactures to be linked together and operate from a single
controller, as long as all xtures and the controller are DMX compli­ant. To ensure proper DMX data transmission, when using several
DMX fixtures try to use the shortest cable path possible. The order
in which fixtures are connected in a DMX line does not influence the
DMX addressing. For example; a fixture assigned a DMX address of 1
may be placed anywhere in a DMX line, at the beginning, at the end,
or anywhere in the middle. When a fixture is assigned a DMX address
of 1, the DMX controller knows to send DATA assigned to address 1
to that unit, no matter where it is located in the DMX chain.

Data Cable (DMX Cable) Requirements (For DMX Operation):

The Dotz Panel 2.4 can be controlled via DMX-512 protocol. The Dotz
Panel 2.4 has 5 DMX Channel Modes. The DMX address is set on the rear
panel of the Dotz Panel 2.4. Your unit and your DMX controller require
a approved DMX-512 110 Ohm Data cable for data input and data
output (Figure 1). We recommend Accu-Cable
DMX cables. If you are making your own cables,
be sure to use standard 110-120 Ohm shielded
cable (This cable may be purchased at almost
all professional sound and lighting stores). Your
cables should be made with a male and female
XLR connector on either end of the cable. Also
remember that DMX cable must be daisy chained
and cannot be split.

ADJ Products, LLC - www.adj.com - Dotz Panel 2.4 User Manual Page 5

Figure 1

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

DMX512

DMX+,DMX-,COMMON

1

2

3

Termination reduces signal errors and
avoids signal transmission problems
and interference. It is always advisable
to connect a DMX terminal, (Resistance
120 Ohm 1/4 W) between PIN 2 (DMX-)
and PIN 3 (DMX +) of the last fixture.

POWER

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

Dotz Panel 2.4 Set Up

Dotz Panel 2.4 System Menu

Notice: Be sure to follow gures two and three when making your own

cables. Do not use the ground lug on the XLR connector. Do not con­nect the cable’s shield conductor to the ground lug or allow the shield
conductor to come in contact with the XLR’s outer casing. Grounding
the shield could cause a short circuit and erratic behavior.

COMMON

1

DMX512 IN

3

3-PIN XLR

2

Figure 2

XLR Pin Conguration

1 Ground

3 Hot

Pin 1 = Ground

Pin 2 = Data Compliment (negative)

Pin 3 = Data True (positive)

When longer runs of cable are

Figure 4

Pin 1

Pin 2

Pin 3

Do Not Use

Do Not Use

XLR Male Socket

1 Ground

DMX512 OUT

3-PIN XLR

2 Cold

3 Hot

1

3

2

DMX +

DMX -

XLR Female Socket

2 Cold

Figure 3

Special Note: Line Termination.

used, you may need to use a terminator on the last unit to avoid erratic
behavior. A terminator is a 90-120 ohm 1/4 watt resistor which is con­nected between pins 2 and 3 of a male XLR connector (DATA + and
DATA -). This unit is inserted in the female XLR connector of the last
unit in your daisy chain to terminate the line. Using a cable terminator
(ADJ part number Z-DMX/T) will decrease the possibilities of erratic
behavior.

5-Pin XLR DMX Connectors.

connectors for DATA transmission in place of 3-pin. 5-pin XLR xtures
may be implemented in a 3-pin XLR DMX line. When inserting standard
5-pin XLR connectors in to a 3-pin line a cable adaptor must be used,
these adaptors are readily available at most electric stores. The chart
below details a proper cable conversion.

Conductor 5-Pin XLR Male (In)3-Pin XLR Female (Out)

Ground/Shield

Data Compliment (- signal)

Data True (+ signal)

Not Used

Not Used

Termination reduces signal errors and

1

avoids signal transmission problems

3

and interference. It is always advisable

2

to connect a DMX terminal, (Resistance
120 Ohm 1/4 W) between PIN 2 (DMX-)
and PIN 3 (DMX +) of the last fixture.

Some manufactures use 5-pin XLR

3-Pin XLR to 5-Pin XLR Conversion

Pin 1

Pin 2

Pin 3

Built-In Programs

STATIC COLOR

CL:RGB Flash00-99

DREAM

Speed00-99 Flash00-99

METEOR

Speed00-99 Flash00-99

FADE

Speed00-99 Flash00-99

CHANGE

Speed00-99 Flash00-99

FLOW 1

Speed00-99 Flash00-99

FLOW 2

Speed00-99 Flash00-99

FLOW 3

Speed00-99 Flash00-99

FLOW 4

Speed00-99 Flash00-99

FLOW 5

Speed00-99 Flash00-99

FLOW 6

Speed00-99 Flash00-99

FLOW 7

Speed00-99 Flash00-99

FLOW 8

Speed00-99 Flash00-99

FLOW 9

Speed00-99 Flash00-99

Blackout,

Red-Green-Blue-Yellow-Cyan-Purple-White

Flash speed adjustable.

Seven color dreaming

Speed & Flash adjustable

Seven color flow

Speed & Flash adjustable

Seven color fade

Speed & Flash adjustable

Seven color change

Speed & Flash adjustable

Seven color chase

Speed & Flash adjustable

Seven color chase

Speed & Flash adjustable

Seven color chase

Speed & Flash adjustable

Seven color chase

Speed & Flash adjustable

Seven color chase

Speed & Flash adjustable

Seven color chase

Speed & Flash adjustable

Seven color chase

Speed & Flash adjustable

Seven color chase

Speed & Flash adjustable

Seven color chase

Speed & Flash adjustable

ADJ Products, LLC - www.adj.com - Dotz Panel 2.4 User Manual Page 6

ADJ Products, LLC - www.adj.com - Dotz Panel 2.4 User Manual Page 7

Dotz Panel 2.4 System Menu

Dotz Panel 2.4 System Menu

The LCD backlight will shut o after 30 seconds, to relight
the background, press the MODE button for 5 seconds.

DMX Mode - Set the DMX Address and DMX Channel

Mode -

1. Press the MENU button until “DMX Mode” and underneath
“ADDR: XXX” and “CH:XX” is displayed, press ENTER.

2. “XXX” will now begin to ash, use the UP and DOWN buttons
to nd your desired DMX address, then press ENTER.

3. “XX” will now begin to ash, use the UP and DOWN buttons to
nd your desired DMX Channel mode, then press ENTER.

Slave Mode - This will let you set your unit as a slave in

a master/slave conguration.

1. Press the MENU button until “Slave Mode” is displayed. Your
unit will now follow the Master.

Sound Mode - In this mode the unit will run in sound

active mode.

2. “FQN:XX” will now be displayed, “XX” representing the Fre­quency Rate (Auto Run speed).

3. Press ENTER and the number will begin to ash, use the UP
and DOWN buttons to adjust the speed, 01 being the slowest
and 99 being the fastest. Press ENTER to conrm.

Built-In Programs - See the chart on page 7 to nd

your desired program.

1. Press the MENU button until one of the Programs on page 7 is

displayed. The displayed program depends on the last program

you had set the unit to.

2. Press ENTER to move through the various adjustments of each
program, and use the UP and DOWN button to make adjust-

ments.

Dim Curve - This setting will let you select your desired

dimming curve.

1. Press the MENU button until “Dim Curve” is displayed, press
ENTER.

1. Press the MENU button until “Sound Mode” is displayed.

2. Press ENTER to adjust your sound sensitivity. When you press
ENTER the number next to “Sens” will begin to ash, use the
UP and DOWN buttons to adjust the sound sensitivity. Once you
found your desired sensitivity press ENTER to conrm.

3. When you press ENTER the number next to “FQN” will not
begin to ash, use the UP and DOWN buttons to adjust the fre­quency rate. Press ENTER to conrm your setting.

Auto Run -

1. Press the MENU button until “Auto Run” is displayed, press
ENTER.

ADJ Products, LLC - www.adj.com - Dotz Panel 2.4 User Manual Page 8

2. 1 of 5 dimming curve settings will be displayed: Standard,
Stage, TV, Architectural, or Theatre. Use the UP and DOWM but­tons to select your desired dimming curve and press ENTER to
conrm.

Pixel Flip - In this mode you adjust the unit so that the

LEDs in DMX mode will illuminate at your desired starting
point.

1. Press the MENU button until “Pixel Flip” is displayed, press
ENTER.

2. Either “OFF” or “ON”, will be displayed. “ON” will have the unit
light up bottom right to left. “OFF” will have the unit light up top

ADJ Products, LLC - www.adj.com - Dotz Panel 2.4 User Manual Page 9

Dotz Panel 2.4 System Menu

Dotz Panel 2.4 Universal DMX Control

left to right. Use the UP or DOWN buttons to nd your desired
setting, and press ENTER.

NO DMX - This mode can be used as a precaution mode,

that in case the DMX signal is lost, the operating mode

chosen in the setup is the running mode the xture will go
into when the DMX signal is lost. You can also set this as
the operating mode you would like the unit to return to when
power is applied.

1. Press the MENU button until “NO DMX” is displayed, and either
“Sound”, “Auto”, “Black”, or “Hold” will be displayed beneath.

2. Press ENTER and the bottom choice will begin to ash. Use
the UP or DOWN buttons to choose an operating mode you
would like the unit to start up in when power is applied or the
DMX signal is lost.

• Sound - If the DMX signal is lost or power is applied, the unit
will automatically go into sound active mode.

• Auto - If the DMX signal is lost or power is applied, the unit will
automatically go into Auto Run mode.

• Black (Blackout) - If the DMX signal is lost or power is applied,
the unit will automatically go into stand by mode.

• Hold - If the DMX signal is lost the xture will stay in the last
DMX setting. If power is applied and this mode is set, the unit will
automatically go into the last DMX set up.

3. Press ENTER to conrm your desired set up.

Personality - This will let you set your unit as a Master in

a master/slave conguration.

1. Press the MENU button until “Personality” is displayed. Your
unit will now be the Master unit in a Master-Slave conguration.

Universal DMX Control: This function allows you to use a Elation®
universal DMX-512 controller to control the chases and patterns,
dimmer and strobe. A DMX controller allows you to create unique
programs tailored to your individual needs. The Dotz Panel 2.4 has 5
DMX channel modes; a 3 Channel Mode, 6 Channel Mode, 8 Channel
Mode, 24 Channel Mode, & 29 Channel Mode. To select your channel
mode see page 8.

1. This function will allow you to control each individual fixture’s
traits with a standard DMX 512 controller such as the
Elation® Show Designer™ or the Elation® DMX Operator.™

2. To run your fixture in DMX mode, follow directions on page 8 to
set your DMX address and DMX Channel mode.

3. Plug in the fixture via the XLR connections to any standard DMX

controller.

4. For longer cable runs (more than a 100 feet) use a terminator on
the last fixture.

Dotz Panel 2.4 Master-Slave Configuration

Master-Slave Operation: This function will allow you to link up to 16

units together and operate without a controller. The units will be sound
activated. In Master-Slave operation one unit will act as the controlling

unit and the others will react to the controlling units programs. Any unit
can act as a Master or as a Slave.

1. Using approved DMX data cables, daisy chain your units together
via the XLR connector on the rear of the units. Remember the
Male XLR connector is the input and the Female XLR connector is
the output. The rst unit in the chain (master) will use the female
XLR connector only - The last unit in the chain will use the male
XLR connector only. For longer cable runs we suggest a termina­ tor at the last fixture.

2. On the Master unit, designate the unit as a “Master” unit following
the instructions on page 10. Then set your desired operating mode.

3. On the slave units press the MODE button until “Slave Mode” is

displayed.

4. The slave units will now follow the Master unit.

ADJ Products, LLC - www.adj.com - Dotz Panel 2.4 User Manual Page 10

ADJ Products, LLC - www.adj.com - Dotz Panel 2.4 User Manual Page 11

Dotz Panel 2.4 Photometrics

Dotz Panel 2.4 3 Channel Mode

Beam angle 25°
Field angle 30°

Intensity(LUX)

Red LEDs
Green LEDs
Blue LEDs
Full LEDs

1245
1683
3220

3

2

1

0

1

Beam opening(m)

2

3

0 1 2 3 4 5

Diameter

25°
30°

(m)

Diameter

(m)

893

0.65

0.75

259
368
487

1005

1.18

1.27

129
172
236
450

1.43

1.70

74

99
135
270

1.87

2.23

47
66
87

176

2.31

2.77

25

30

Channel Value Function
1 RED

0 - 255 0% - 100%
2 GREEN
0 - 255 0% - 100%
3 BLUE
0 - 255 0% - 100%

Dotz Panel 2.4 6 Channel Mode

Channel Value Function
1 RED

0 - 255 0% - 100%
2 GREEN
0 - 255 0% - 100%
3 BLUE
0 - 255 0% - 100%
4 MASTER DIMMER
0 - 255 0% - 100%
5 STROBING
0 - 255 SLOW - FAST
6 DIMMER CURVES
0 - 41 STANDARD
42 - 84 STAGE
85 - 127 TV
128 - 170 ARCHITECTURAL
171 - 213 THEATER
214 - 255 DEFAULT TO UNIT CURVE SETTING

ADJ Products, LLC - www.adj.com - Dotz Panel 2.4 User Manual Page 12

ADJ Products, LLC - www.adj.com - Dotz Panel 2.4 User Manual Page 13

Dotz Panel 2.4 8 Channel Mode

Dotz Panel 2.4 8 Channel Mode

Channel Value Function
1 RED

0 - 255 0% - 100%
2 GREEN
0 - 255 0% - 100%
3 BLUE
0 - 255 0% - 100%
4 COLOR MACROS & PROGRAMS
0 - 15 NO FUNCTION
16 - 23 RED
24 - 31 GREEN
32 - 39 BLUE
40 - 47 RED & GREEN
48 - 55 GREEN & BLUE
56 - 63 RED & BLUE
64 - 71 RED, GREEN, & BLUE
72 - 79 COLOR 1
80 - 87 COLOR 2
88 - 95 COLOR 3
96 - 103 COLOR 4
104 - 111 COLOR 5
112 - 119 COLOR 6
120 - 127 COLOR 7
128 - 135 COLOR 8
136 - 143 COLOR FADE 1
144 - 151 COLOR SNAKE
152 - 159 COLOR FADE 2
160 - 167 COLOR CHANGE
168 - 175 COLOR FLOW 1
176 - 183 COLOR FLOW 2
184 - 191 COLOR FLOW 3
192 - 199 COLOR FLOW 4
200 - 207 COLOR FLOW 5
208 - 215 COLOR FLOW 6
216 - 223 COLOR FLOW 7

Channel Value Function
4 COLOR MACROS & PROGRAMS

216 - 223 COLOR FLOW 7
224 - 231 COLOR FLOW 8
232 - 239 COLOR FLOW 9
240 - 247 COLOR FLOW 10
248 - 255 N/G
5 PROGRAM SPEED/SOUND SENSE
0 - 255 PROGRAM SPEED SLOW - FAST
6 0 - 255 MASTER DIMMER 0% - 100%
7 STROBING
0 - 255 SLOW - FAST
8 DIMMER CURVES
0 - 41 STANDARD
42 - 84 STAGE
85 - 127 TV
128 - 170 ARCHITECTURAL
171 - 213 THEATER
214 - 255 DEFAULT TO UNIT CURVE SETTING

When Channel 4 is being used between the values of 136-239,
Channel 5 will control the speed of the programs.

When Channel 4 is being used between the values of 240-255,
Channel 5 will control sound sensitivity.

ADJ Products, LLC - www.adj.com - Dotz Panel 2.4 User Manual Page 14

ADJ Products, LLC - www.adj.com - Dotz Panel 2.4 User Manual Page 15

Dotz Panel 2.4 24 Channel Mode

Dotz Panel 2.4 29 Channel Mode

Channel Value Function
1 RED 1

0 - 255 0% - 100%
2 GREEN 1
0 - 255 0% - 100%
3 BLUE 1
0 - 255 0% - 100%
4 RED 2
0 - 255 0% - 100%
5 GREEN 2
0 - 255 0% - 100%
6 BLUE 2
0 - 255 0% - 100%
7 RED 3
0 - 255 0% - 100%
8 GREEN 3
0 - 255 0% - 100%
9 BLUE 3
0 - 255 0% - 100%

*Channels 10-18 continue the same RGB LED Pattern*

19 RED 7
0 - 255 0% - 100%
20 GREEN 7
0 - 255 0% - 100%
21 BLUE 7
0 - 255 0% - 100%
22 RED 8
0 - 255 0% - 100%
23 GREEN 8
0 - 255 0% - 100%
24 BLUE 8
0 - 255 0% - 100%

Channel Value Function
1 RED 1

0 - 255 0% - 100%
2 GREEN 1
0 - 255 0% - 100%
3 BLUE 1
0 - 255 0% - 100%
4 RED 2
0 - 255 0% - 100%
5 GREEN 2
0 - 255 0% - 100%
6 BLUE 2
0 - 255 0% - 100%
7 RED 3
0 - 255 0% - 100%
8 GREEN 3
0 - 255 0% - 100%
9 BLUE 3
0 - 255 0% - 100%

*Channels 10-18 continue the same RGB LED Pattern*

19 RED 7
0 - 255 0% - 100%
20 GREEN 7
0 - 255 0% - 100%
21 BLUE 7
0 - 255 0% - 100%
22 RED 8
0 - 255 0% - 100%
23 GREEN 8
0 - 255 0% - 100%
24 BLUE 8
0 - 255 0% - 100%

ADJ Products, LLC - www.adj.com - Dotz Panel 2.4 User Manual Page 16 ADJ Products, LLC - www.adj.com - Dotz Panel 2.4 User Manual Page 17

Dotz Panel 2.4 29 Channel Mode

Dotz Panel 2.4 29 Channel Mode

Channel Value Function
25 COLOR MACROS & PROGRAMS

0 - 15 NO FUNCTION
16 - 23 RED
24 - 31 GREEN
32 - 39 BLUE
40 - 47 RED & GREEN
48 - 55 GREEN & BLUE
56 - 63 RED & BLUE
64 - 71 RED, GREEN, & BLUE
72 - 79 COLOR 1
80 - 87 COLOR 2
88 - 95 COLOR 3
96 - 103 COLOR 4
104 - 111 COLOR 5
112 - 119 COLOR 6
120 - 127 COLOR 7
128 - 135 COLOR 8
136 - 143 COLOR FADE 1
144 - 151 COLOR SNAKE
152 - 159 COLOR FADE 2
160 - 167 COLOR CHANGE
168 - 175 COLOR FLOW 1
176 - 183 COLOR FLOW 2
184 - 191 COLOR FLOW 3
192 - 199 COLOR FLOW 4
200 - 207 COLOR FLOW 5
208 - 215 COLOR FLOW 6
216 - 223 COLOR FLOW 7
216 - 223 COLOR FLOW 7
224 - 231 COLOR FLOW 8
232 - 239 COLOR FLOW 9
240 - 255 SOUND ACTIVE

Channel Value Function
26 PROGRAM SPEED/SOUND SENSE

0 - 255 PROGRAM SPEED SLOW - FAST
27 0 - 255 MASTER DIMMER 0% - 100%
28 STROBING
0 - 255 SLOW - FAST
29 DIMMER CURVES
0 - 41 STANDARD
42 - 84 STAGE
85 - 127 TV
128 - 170 ARCHITECTURAL
171 - 213 THEATER
214 - 255 DEFAULT TO UNIT CURVE SETTING

When Channel 25 is being used between the values of 136-239,
Channel 26 will control the speed of the programs.

When Channel 25 is being used between the values of 240-255,
Channel 26 will control sound sensitivity.

ADJ Products, LLC - www.adj.com - Dotz Panel 2.4 User Manual Page 18

ADJ Products, LLC - www.adj.com - Dotz Panel 2.4 User Manual Page 19

Dotz Panel 2.4 Installation

Dotz Panel 2.4 Fuse Replacement

When installing the unit, the trussing or area of installation must be
able to hold 10 times the weight without any deformation. When
installing the unit must be secured with a secondary safety attach­ment, e.g. and appropriate safety cable. Never stand directly below
the unit when mounting, removing, or servicing the unit.

Overhead mounting requires extensive experience, including calculat­ing working load limits, installation material being used, and perodic
safety inspection of all installation material and unit. If you lack these
qualications, do not attempt the installation yourself.

These installaiton should be checked by a skilled person once a year.

The Dotz Panel 2.4 is fully operational in two dierent mounting posi­tions, hanging upside-down from a ceiling or set on a at level sur­face. To avoid internal damage to the unit, never mount the unit on
its side as illustrated above. Be sure this xture is kept at least 0.5m
away from any ammable materials (decoration etc.). Always use and
install the supplied safety cable as a safety measure to prevent acci­dental damage and/or injury in the event the clamp fails. Never use

the carrying handles for secondary attachment.

Dotz Panel 2.4 Power Cord Daisy Chaining

With this feature you can connect the xtures to one another

using the IEC input and output sockets. The quantity that can be

connected is 8 xtures maximum for 120V, and 17 xtures maxi­mum for 230V. After the maximum xtures has been reached you
will need to use a new power outlet. They must be the same x­tures. DO NOT mix xtures.

Locate and remove the unit’s power cord. Once the cord has been
removed located the fuse holder located inside the power socket.
Insert a flat-head screw driver into the power socket and gently pry out
the fuse holder. Remove the bad fuse and replace with a new one. The
fuse holder has a built-in socket for a spare fuse be sure not to confuse
the spare fuse with active fuse.

Dotz Panel 2.4 Cleaning

Due to fog residue, smoke, and dust cleaning the internal and exter­nal optical lenses must be carried out periodically to optimize light
output.

1. Use a soft cloth to wipe down the outside casing.

Cleaning frequency depends on the environment in which the fixture
operates (i.e. smoke, fog residue, dust, dew).

Dotz Panel 2.4 Troubleshooting

Listed below are a few common problems the user may encounter,
with solutions.

Unit not responding to DMX:

1. Check that the DMX cables are connected properly and are
wired correctly (pin 3 is “hot”; on some other DMX devices
pin 2 may be ‘hot’). Also, check that all cables are connected
to the right connectors; it does matter which way the inputs
and outputs are connected.

Unit does not respond to sound:

1. Quiet or high pitched sounds will not activate the unit.

If problems are not resolved; Contact ADJ Products, LLC for service.

1-800-322-6337

ADJ Products, LLC - www.adj.com - Dotz Panel 2.4 User Manual Page 20 ADJ Products, LLC - www.adj.com - Dotz Panel 2.4 User Manual Page 21

Dotz Panel 2.4 Warranty

MANUFACTURER’S LIMITED WARRANTY

A. ADJ Products, LLC hereby warrants, to the original purchaser, ADJ Products, LLC products
to be free of manufacturing defects in material and workmanship for a prescribed period from
the date of purchase (see specific warranty period on reverse). This warranty shall be valid only if the
product is purchased within the United States of America, including possessions and
territories. It is the owner’s responsibility to establish the date and place of purchase by acceptable
evidence, at the time service is sought.

B. For warranty service you must obtain a Return Authorization number (RA#) before sending back
the product–please contact ADJ Products, LLC Service Department at 800-322-6337. Send the pro­ duct only to the ADJ Products, LLC factory. All shipping charges must be pre-paid. If the requested
repairs or service (including parts replacement) are within the terms of this warranty, ADJ Products, LLC
will pay return shipping charges only to a designated point within the United States. If the entire instru­ ment is sent, it must be shipped in it’s original package. No accessories should be shipped with the product.
If any accessories are shipped with the product, ADJ Products, LLC shall have no liability whatsoever for
loss of or damage to any such accessories, nor for the safe return thereof.

C. This warranty is void if the serial number has been altered or removed; if the product is modified in any
manner which ADJ Products, LLC concludes, after inspection, affects the reliability of the product; if the
product has been repaired or serviced by anyone other than the ADJ Products, LLC factory unless prior
written authorization was issued to purchaser by ADJ Products, LLC; if the product is damaged because
not properly maintained as set forth in the instruction manual.

D. This is not a service contract, and this warranty does not include maintnance, cleaning or periodic check
up. During the period specified above, ADJ Products, LLC will replace defective parts at its expense
with new or refurbished parts, and will absorb all expenses for warranty service and repair labor by
reason of defects in material or workmanship. The sole responsibility of ADJ Products, LLC under this
warranty shall be limited to the repair of the product, or replacement thereof, including parts, at the sole
discretion of ADJ Products, LLC. All products covered by this warranty were manufactured after August
15, 2012, and bear indentifying marks to that effect.

E. ADJ Products, LLC reserves the right to make changes in design and/or improvements upon its products
without any obligation to include these changes in any products theretofore manufactured.

No warranty, whether expressed or implied, is given or made with respect to any accessory supplied with
products described above. Except to the extent prohibited by applicable law, all implied warranties made
by ADJ Products, LLC in connection with this product, including warranties of merchantability or fitness,
are limited in duration to the warranty period set forth above. And no warranties, whether expressed or
implied, including warranties of merchantability or fitness, shall apply to this product after said period
has expired. The consumer’s and/or Dealer’s sole remedy shall be such repair or replacement as is
expressly provided above; and under no circumstances shall ADJ Products, LLC be liable for any loss or
damage, direct or consequential, arising out of the use of, or inability to use, this product.

This warranty is the only written warranty applicable to ADJ Products, LLC Products and
supersedes all prior warranties and written descriptions of warranty terms and conditions heretofore
published.

MANUFACTURER’S LIMITED WARRANTY PERIODS:

 •LightingProducts=1-year(365days)LimitedWarranty(Such as: Special Effect Lighting, Intelligent

Lighting, UV lighting, Strobes, Fog Machines, Bubble Machines, Mirror Balls, Par Cans, Trussing,
Lighting Stands etc. excluding LED and lamps)

 •LaserProducts=90-DayLimitedWarranty
 •L.E.D.Products=3-year(1095days)LimitedWarranty(excluding motors, PCB boards, and power

supplies, which have a 1-year (365 day Limited Warranty) and batteries which have a 180 day
limited warranty). Only the L.E.D.s carry a 3-year warranty

ADJ Products, LLC - www.adj.com - Dotz Panel 2.4 User Manual Page 22

Dotz Panel 2.4 Specifications

SPECIFICATIONS:
Voltage: 100V~240V 50Hz/60Hz
LEDs: 8 x 9W COB TRI LEDs
Power Consumption: 106W Total (All LED’s @ Full)
Beam Angle: 25 Degrees
Fuse: 2Amp
Power Cord Daisy Chain: 8 Fixtures Max. (120V)
17 Fixtures Max. (230V)
Weight: 14lbs./ 6.4Kgs.
Dimensions: 13.5” (L) x 6.5” (W) x 9” (H)
345 x 164 x 227mm
Colors: RGB Color Mixing
DMX Channels: 3 Channel Mode, 6 Channel Mode,
8 Channel Mode, 24 Channel
Mode, & 29 Channel Mode
Working Position: Any safe working position
Warranty: 3 Year (1095 days)

Auto Sensing Voltage: This xture contains a automatic volt-

age switch, which will auto sense the voltage when it is plugged
into the power source.

Please Note: Specications and improvements in the design of
this unit and this manual are subject to change without any prior
written notice.

ADJ Products, LLC

6122 S. Eastern Ave. Los Angeles, CA 90040 USA

Tel: [phone] / Fax: [phone]

Web: www.adj.com / E-mail: [e-mail]

A.D.J. Supply Europe B.V.

Junostraat 2

6468 EW Kerkrade

Netherlands

[e-mail] / www.adj.eu

Tel: [phone] / Fax: [phone]