ADJ Dotz Matrix Users Manual

DOTZ MATRIX
©2013 ADJ Products, LLC all rights reserved. Information,
specications, diagrams, images, and instructions herein are subject to change without notice. ADJ Products, LLC logo and identifying product names and numbers herein are trademarks of ADJ Products, LLC. Copyright protection claimed includes all forms and matters of copyrightable materials and information now allowed by statutory or judicial law or hereinafter granted. Product names used in this document may be trademarks or registered trademarks of their respective companies and are hereby acknowledged. All non-ADJ Products, LLC brands and product names are trademarks or registered trademarks of their
respective companies.
ADJ Products, LLC and all aliated companies hereby dis­claim any and all liabilities for property, equipment, building, and electrical damages, injuries to any persons, and direct or indi­rect economic loss associated with the use or reliance of any information contained within this document, and/or as a result of the improper, unsafe, unsucient and negligent assembly, installation, rigging, and operation of this product.
Rev. 3/14
User Instructions
Europe Energy Saving Notice Energy Saving Matters (EuP 2009/125/EC) Saving electric energy is a key to help protecting the enviroment. Please turn o all electrical products when they are not in use. To avoid power consumption in idle mode, disconnect all electrical equipment from power when not in use. Thank you!
Dotz Matrix Introduction
Dotz Matrix General Instructions
Unpacking: Thank you for purchasing the Dotz Matrix by ADJ Prod-
ucts, LLC. Every Dotz Matrix has been thoroughly tested and has been shipped in perfect operating condition. Carefully check the shipping carton for damage that may have occurred during shipping. If the carton appears to be damaged, carefully inspect your xture for any damage and be sure all accessories necessary to operate the unit has arrived intact. In the case damage has been found or parts are miss­ing, please contact our toll free customer support number for further instructions. Do not return this unit to your dealer without rst contact­ing customer support.
Introduction: The Dotz Matrix is part of ADJ’s continuing pursuit for
creating high quality affordable intelligent fixtures. The Dotz Matrix is a high performance, DMX intelligent, moving head LED fixture. This fixture is a great piece for retail stores, displays, mood, architectural, interior and exterior decoration, and clubs. This unit can be used as a stand alone, or in a Master/Slave conguration. The unit can also be controlled via DMX controller. This fixture is suitable for theaters, stu-
dios, retail stores, and other similar locations.
Customer Support: ADJ Products, LLC provides a toll free cus-
tomer support line, to provide set up help and to answer any question should you encounter problems during your set up or initial operation. You may also visit us on the web at www.adj.com for any comments or suggestions. Service Hours are Monday through Friday 8:00 a.m. to 4:30 p.m. Pacic Standard Time. Voice: (800) 322-6337 Fax: (323) 582-2941 E-mail: support@americandj.com To purchase parts online visit http://parts.americandj.com
To optimize the performance of this product, please read these operat­ing instructions carefully to familiarize yourself with the basic operations of this unit. These instructions contain important safety information regarding the use and maintenance of this unit. Please keep this manual with the unit, for future reference.
Dotz Matrix Features
• RGB Color Mixing
• Strobing
• Electronic Dimming 0-100%
• Built in Microphone
• DMX-512 protocol
• Five DMX Modes: 3 Channel Mode, 6 Channel Mode, 7 Channel Mode, 48 Channel Mode, & 52 Channel Mode
• 4 Operating Modes - Sound Active, Programs Mode, Auto Run, and DMX Control
• Power Cord Daisy Chaining (See Page 21)
Dotz Matrix Warranty Registration
The Dotz Matrix carries a 2 year (730 days) limited warranty. Please fill out the enclosed warranty card to validate your purchase and war-
ranty. You may also register your product online at www. americandj. com. All returned service items whether under warranty or not, must
be freight pre-paid and accompany a return authorization (R.A.) num­ber. If the unit is under warranty you must provide a copy of your proof of purchase invoice. Please contact ADJ Products, LLC cus­tomer support for a R.A. number.
Warning! To prevent or reduce the risk of electrical shock or re, do
not expose this unit to rain or moisture.
Caution! There are no user serviceable parts inside this unit. Do not
attempt any repairs yourself, doing so will void your manufactures war­ranty. In the unlikely event your unit may require service please contact ADJ Products, LLC.
PLEASE recycle the shipping carton when ever possible.
ADJ Products, LLC - www.adj.com - Dotz Matrix User Manual Page 2
ADJ Products, LLC - www.adj.com - Dotz Matrix User Manual Page 3
Dotz Matrix Safety Precautions
Dotz Matrix Set Up
• To reduce the risk of electrical shock or re, do not expose this unit rain or moisture
• Do not spill water or other liquids into or on to your unit.
• Be sure that the local power outlet match that of the required volt­ age for your unit.
• Do not attempt to operate this unit if the power cord has been frayed or broken. Do not attempt to remove or break o the ground prong from the electrical cord. This prong is used to reduce the risk of electrical shock and re in case of an internal short.
• Disconnect from main power before making any type of connection.
• Do not remove the cover under any conditions. There are no user serviceable parts inside.
• Never operate this unit when it’s cover is removed.
• Never plug this unit in to a dimmer pack
• Always be sure to mount this unit in an area that will allow proper ventilation. Allow about 6” (15cm) between this device and a wall.
• Do not attempt to operate this unit, if it becomes damaged.
• This unit is intended for indoor use only, use of this product out` doors voids all warranties.
• During long periods of non-use, disconnect the unit’s main power.
• Always mount this unit in safe and stable matter.
• Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to the point they exit from the unit.
• Cleaning -The fixture should be cleaned only as recommended by t he manufacturer. See page 21 for cleaning details.
• Heat -The appliance should be situated away from heat sources such as radiators, heat registers, stoves, or other appliances (inclu­ d ing amplifiers) that produce heat.
• The fixture should be serviced by qualified service personnel when: A. The power-supply cord or the plug has been damaged. B. Objects have fallen, or liquid has been spilled into the appliance. C. The appliance has been exposed to rain or water. D. The appliance does not appear to operate normally or exhibits a marked change in performance.
Power Supply: The ADJ Dotz Matrix contains a automatic voltage
switch, which will auto sense the voltage when it is plugged into a power source. With this switch there is no need to worry about the cor­rect power voltage, this unit can be plugged in anywhere. Always use the PowerCon cord that came with the unit.
DMX-512: DMX is short for Digital Multiplex. This is a universal pro-
tocol used as a form of communication between intelligent fixtures and controllers. A DMX controller sends DMX data instructions from the controller to the fixture. DMX data is sent as serial data that trav­els from fixture to fixture via the DATA “IN” and DATA “OUT” XLR ter­minals located on all DMX fixtures (most controllers only have a DATA “OUT” terminal).
DMX Linking: DMX is a language allowing all makes and models of dierent manufactures to be linked together and operate from a single controller, as long as all xtures and the controller are DMX compli­ant. To ensure proper DMX data transmission, when using several DMX fixtures try to use the shortest cable path possible. The order in which fixtures are connected in a DMX line does not influence the DMX addressing. For example; a fixture assigned a DMX address of 1 may be placed anywhere in a DMX line, at the beginning, at the end, or anywhere in the middle. When a fixture is assigned a DMX address of 1, the DMX controller knows to send DATA assigned to address 1 to that unit, no matter where it is located in the DMX chain.
Data Cable (DMX Cable) Requirements (For DMX Operation):
The Dotz Matrix can be controlled via DMX-512 protocol. The Dotz Matrix has 5 DMX Channel Modes. The DMX address is set on the rear panel of the Dotz Matrix. Your unit and your DMX controller require a approved DMX-512 110 Ohm Data cable for data input and data output (Figure
1). We recommend Accu-Cable DMX cables. If you are making your own cables, be sure to use standard 110-120 Ohm shielded cable (This cable may be purchased at almost all professional sound and lighting stores). Your cables should be made with a male and female XLR connector on either end of the cable. Also remember that DMX cable must be daisy chained and cannot be split.
ADJ Products, LLC - www.adj.com - Dotz Matrix User Manual Page 4
Figure 1
ADJ Products, LLC - www.adj.com - Dotz Matrix User Manual Page 5
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
DMX512
DMX+,DMX-,COMMON
1
2
3
Termination reduces signal errors and avoids signal transmission problems and interference. It is always advisable to connect a DMX terminal, (Resistance 120 Ohm 1/4 W) between PIN 2 (DMX-) and PIN 3 (DMX +) of the last fixture.
POWER
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
Dotz Matrix Set Up
Notice: Be sure to follow gures two and three when making your own
cables. Do not use the ground lug on the XLR connector. Do not con­nect the cable’s shield conductor to the ground lug or allow the shield conductor to come in contact with the XLR’s outer casing. Grounding the shield could cause a short circuit and erratic behavior.
COMMON
1
DMX512 IN
3
3-PIN XLR
2
Figure 2
XLR Pin Conguration
1 Ground
3 Hot
Pin 1 = Ground
Pin 2 = Data Compliment (negative)
Pin 3 = Data True (positive)
When longer runs of cable are
Figure 4
Pin 1
Pin 2
Pin 3
Do Not Use
Do Not Use
XLR Male Socket
1 Ground
DMX512 OUT
3-PIN XLR
2 Cold
3 Hot
1
3
2
DMX +
DMX -
XLR Female Socket
2 Cold
Figure 3
Special Note: Line Termination.
used, you may need to use a terminator on the last unit to avoid erratic behavior. A terminator is a 90-120 ohm 1/4 watt resistor which is con­nected between pins 2 and 3 of a male XLR connector (DATA + and DATA -). This unit is inserted in the female XLR connector of the last unit in your daisy chain to terminate the line. Using a cable terminator (ADJ part number Z-DMX/T) will decrease the possibilities of erratic behavior.
5-Pin XLR DMX Connectors.
connectors for DATA transmission in place of 3-pin. 5-pin XLR xtures may be implemented in a 3-pin XLR DMX line. When inserting standard 5-pin XLR connectors in to a 3-pin line a cable adaptor must be used, these adaptors are readily available at most electric stores. The chart below details a proper cable conversion.
Conductor 5-Pin XLR Male (In)3-Pin XLR Female (Out)
Ground/Shield
Data Compliment (- signal)
Data True (+ signal)
Not Used
Not Used
Termination reduces signal errors and
1
avoids signal transmission problems
3
and interference. It is always advisable
2
to connect a DMX terminal, (Resistance 120 Ohm 1/4 W) between PIN 2 (DMX-) and PIN 3 (DMX +) of the last fixture.
Some manufactures use 5-pin XLR
3-Pin XLR to 5-Pin XLR Conversion
Pin 1
Pin 2
Pin 3
Dotz Matrix System Menu
Built-In Programs
STATIC COLOR
CL:RGB Flash00-99
DREAM
Speed00-99 Flash00-99
COLOR SNAKE
Speed00-99 Flash00-99
FADE
Speed00-99 Flash00-99
CHANGE
Speed00-99 Flash00-99
FLOW 1
Speed00-99 Flash00-99
FLOW 2
Speed00-99 Flash00-99
FLOW 3
Speed00-99 Flash00-99
FLOW 4
Speed00-99 Flash00-99
FLOW 5
Speed00-99 Flash00-99
FLOW 6
Speed00-99 Flash00-99
FLOW 7
Speed00-99 Flash00-99
FLOW 8
Speed00-99 Flash00-99
FLOW 9
Speed00-99 Flash00-99
FLOW 10
Speed00-99 Flash00-99
Blackout,
Red-Green-Blue-Yellow-Cyan-Purple-White
Flash speed adjustable.
Seven color dreaming
Speed & Flash adjustable
Seven color flow
Speed & Flash adjustable
Seven color fade
Speed & Flash adjustable
Seven color change
Speed & Flash adjustable
Seven color chase
Speed & Flash adjustable
Seven color chase
Speed & Flash adjustable
Seven color chase
Speed & Flash adjustable
Seven color chase
Speed & Flash adjustable
Seven color chase
Speed & Flash adjustable
Seven color chase
Speed & Flash adjustable
Seven color chase
Speed & Flash adjustable
Seven color chase
Speed & Flash adjustable
Seven color chase
Speed & Flash adjustable
Seven color chase
Speed & Flash adjustable
ADJ Products, LLC - www.adj.com - Dotz Matrix User Manual Page 6
ADJ Products, LLC - www.adj.com - Dotz Matrix User Manual Page 7
Dotz Matrix System Menu
Dotz Matrix System Menu
DMX Mode - Set the DMX Address and DMX Channel
Mode -
1. Press the MENU button until “DMX Mode” and underneath “ADDR: XXX” and “CH:XX” is displayed, press ENTER.
2. “XXX” will now begin to ash, use the UP and DOWN buttons to nd your desired DMX address, then press ENTER.
3. “XX” will now begin to ash, use the UP and DOWN buttons to nd your desired DMX Channel mode, then press ENTER.
Slave Mode - This will let you set your unit as a slave in
a master/slave conguration.
1. Press the MENU button until “Slave Mode” is displayed. Your unit will now follow the Master.
Sound Mode - In this mode the unit will run in sound
active mode.
1. Press the MENU button until “Sound Mode” is displayed.
2. Press ENTER to adjust your sound sensitivity. When you press ENTER the number next to “Sens” will begin to ash, use the UP and DOWN buttons to adjust the sound sensitivity. Once you found your desired sensitivity press ENTER to conrm.
3. When you press ENTER the number next to “FQN” will not begin to ash, use the UP and DOWN buttons to adjust the fre­quency rate. Press ENTER to conrm your setting.
Auto Run -
quency Rate (Auto Run speed).
3. Press ENTER and the number will begin to ash, use the UP and DOWN buttons to adjust the speed, 01 being the slowest and 99 being the fastest. Press ENTER to conrm.
Built-In Programs - See the chart on page 7 to nd
your desired program.
1. Press the MENU button until one of the Programs on page 7 is displayed. The displayed program depends on the last program you had set the unit to.
2. Press ENTER to move through the various adjustments of each program, and use the UP and DOWN button to make adjust-
ments.
Pixel Flip - In this mode you adjust the unit so that the
LEDs in DMX mode will illuminate at your desired starting point. See page 12 for the different settings. Example: If the unit is set to Flip 1, in 48 Channel mode, the
rst pixel will light up starting on the top right. If set to Flip 2, in 48 Channel mode, the rst pixel will light up starting on
the bottom right.
1. Press the MENU button until “Pixel Flip” is displayed, press ENTER.
2. Either “Standard” or “Flip X”, “X” representing a number between 1-4. Use the UP or DOWN buttons to nd your desired
setting.
1. Press the MENU button until “Auto Run” is displayed, press ENTER.
2. “FQN:XX” will now be displayed, “XX” representing the Fre-
ADJ Products, LLC - www.adj.com - Dotz Matrix User Manual Page 8
Dim Curve - This setting will let you select your desired
dimming curve.
1. Press the MENU button until “Dim Curve” is displayed, press ENTER.
ADJ Products, LLC - www.adj.com - Dotz Matrix User Manual Page 9
Dotz Matrix System Menu
Dotz Matrix Universal DMX Control
2. 1 of 5 dimming curve settings will be displayed: Standard, Stage, TV, Architectural, or Theatre. Use the UP and DOWN but­tons to select your desired dimming curve and press ENTER to conrm.
Dotz Matrix Photometrics
Beam angle 60° Field angle 80°
Intensity(LUX)
Red LEDs Green LEDs Blue LEDs Full LEDs
Beam opening(m)
60° Diameter(m) 80° Diameter(m)
2130 3050 4730
10140
681
793 1405 2630
302 398 716
1360
197 246 368 730
4
3
2
1
0
1
2
3
4
0 1 2 3 4 5
2.65
3.65
3.75
5.33
4.90
7.00
136 173 224 476
6.05
8.70
60
80
Universal DMX Control: This function allows you to use a Elation® universal DMX-512 controller to control the chases and patterns, dimmer and strobe. A DMX controller allows you to create unique programs tailored to your individual needs. The Dotz Matrix has 5 DMX channel modes; a 3 Channel Mode, 6 Channel Mode, 7 Channel Mode, 48 Channel Mode, & 52 Channel Mode. To select your channel mode see page 8.
1. This function will allow you to control each individual fixture’s traits with a standard DMX 512 controller such as the Elation® Show Designer™ or the Elation® DMX Operator.™
2. To run your fixture in DMX mode, follow directions on page 8 to set your DMX address and DMX Channel mode.
3. Plug in the fixture via the XLR connections to any standard DMX
controller.
4. For longer cable runs (more than a 100 feet) use a terminator on the last fixture.
Dotz Matrix Master-Slave Configuration
Master-Slave Operation: This function will allow you to link up to 16
units together and operate without a controller. The units will be sound activated. In Master-Slave operation one unit will act as the controlling
unit and the others will react to the controlling units programs. Any unit can act as a Master or as a Slave.
1. Using approved DMX data cables, daisy chain your units together via the XLR connector on the rear of the units. Remember the Male XLR connector is the input and the Female XLR connector is the output. The rst unit in the chain (master) will use the female XLR connector only - The last unit in the chain will use the male XLR connector only. For longer cable runs we suggest a termina­ tor at the last fixture.
2. On the Master unit set your desired operating mode.
3. On the slave units press the MODE button until “Slave Mode” is
displayed.
4. The slave units will now follow the Master unit.
ADJ Products, LLC - www.adj.com - Dotz Matrix User Manual Page 10
ADJ Products, LLC - www.adj.com - Dotz Matrix User Manual Page 11
Dotz Matrix Pixel Flip Settings
STANDARD
1 2 3 4
8 7 6 5
9 10 11 12
16 15 14 13
Dotz Matrix 3 Channel Mode
Channel Value Function 1 RED
0 - 255 0% - 100% 2 GREEN 0 - 255 0% - 100% 3 BLUE 0 - 255 0% - 100%
Flip 1
4 3 2 1
5 6 7 8
12 11 10 9
13 14 15 16
Flip 2
13 14 15 16
12 11 10 9
5 6 7 8
4 3 2 1
Flip 3
16 15 14 13
9 10 11 12
8 7 6 5
1 2 3 4
Dotz Matrix 6 Channel Mode
Channel Value Function 1 RED
0 - 255 0% - 100% 2 GREEN 0 - 255 0% - 100% 3 BLUE 0 - 255 0% - 100% 4 MASTER DIMMER 0 - 255 0% - 100% 5 STROBING 0 - 255 SLOW - FAST 6 DIMMER CURVES 0 - 41 STANDARD 42 - 84 STAGE 85 - 127 TV 128 - 170 ARCHITECTURAL 171 - 213 THEATER 214 - 255 DEFAULT TO UNIT CURVE SETTING
Flip4
1 2 3 4
5 6 7 8
9 10 11 12
13 14 15 16
ADJ Products, LLC - www.adj.com - Dotz Matrix User Manual Page 12
ADJ Products, LLC - www.adj.com - Dotz Matrix User Manual Page 13
Dotz Matrix 7 Channel Mode
Dotz Matrix 7 Channel Mode
Channel Value Function 1 RED
0 - 255 0% - 100% 2 GREEN 0 - 255 0% - 100% 3 BLUE 0 - 255 0% - 100% 4 COLOR MACROS & PROGRAMS 0 - 15 NO FUNCTION 16 - 23 RED 24 - 31 GREEN 32 - 39 BLUE 40 - 47 RED & GREEN 48 - 55 GREEN & BLUE 56 - 63 RED & BLUE 64 - 71 RED, GREEN, & BLUE 72 - 79 COLOR 1 80 - 87 COLOR 2 88 - 95 COLOR 3 96 - 103 COLOR 4 104 - 111 COLOR 5 112 - 119 COLOR 6 120 - 127 COLOR 7 128 - 135 COLOR 8 136 - 143 COLOR FADE 1 144 - 151 COLOR SNAKE 152 - 159 COLOR FADE 2 160 - 167 COLOR CHANGE 168 - 175 COLOR FLOW 1 176 - 183 COLOR FLOW 2 184 - 191 COLOR FLOW 3 192 - 199 COLOR FLOW 4 200 - 207 COLOR FLOW 5 208 - 215 COLOR FLOW 6 216 - 223 COLOR FLOW 7
Channel Value Function 4 COLOR MACROS & PROGRAMS
216 - 223 COLOR FLOW 7 224 - 231 COLOR FLOW 8 232 - 239 COLOR FLOW 9 240 - 247 COLOR FLOW 10 248 - 255 N/G 5 MASTER DIMMER/PROGRAM SPEED 0 - 255 MASTER DIMMER 0% - 100% 0 - 255 PROGRAM SPEED SLOW - FAST 6 STROBING 0 - 255 SLOW - FAST 7 DIMMER CURVES 0 - 41 STANDARD 42 - 84 STAGE 85 - 127 TV 128 - 170 ARCHITECTURAL 171 - 213 THEATER 214 - 255 DEFAULT TO UNIT CURVE SETTING
When Channel 4 is being used between the values of 136-247, Channel 5 will control the speed of the programs.
ADJ Products, LLC - www.adj.com - Dotz Matrix User Manual Page 14
ADJ Products, LLC - www.adj.com - Dotz Matrix User Manual Page 15
Dotz Matrix 48 Channel Mode
Dotz Matrix 52 Channel Mode
Channel Value Function 1 RED 1
0 - 255 0% - 100% 2 GREEN 1 0 - 255 0% - 100% 3 BLUE 1 0 - 255 0% - 100% 4 RED 2 0 - 255 0% - 100% 5 GREEN 2 0 - 255 0% - 100% 6 BLUE 2 0 - 255 0% - 100% 7 RED 3 0 - 255 0% - 100% 8 GREEN 3 0 - 255 0% - 100% 9 BLUE 3 0 - 255 0% - 100%
*Channels 10-42 continue the same RGB LED Pattern*
43 RED 15 0 - 255 0% - 100% 44 GREEN 15 0 - 255 0% - 100% 45 BLUE 15 0 - 255 0% - 100% 46 RED 16 0 - 255 0% - 100% 47 GREEN 16 0 - 255 0% - 100% 48 BLUE 16 0 - 255 0% - 100%
Channel Value Function 1 RED 1
0 - 255 0% - 100% 2 GREEN 1 0 - 255 0% - 100% 3 BLUE 1 0 - 255 0% - 100% 4 RED 2 0 - 255 0% - 100% 5 GREEN 2 0 - 255 0% - 100% 6 BLUE 2 0 - 255 0% - 100% 7 RED 3 0 - 255 0% - 100% 8 GREEN 3 0 - 255 0% - 100% 9 BLUE 3 0 - 255 0% - 100%
*Channels 10-42 continue the same RGB LED Pattern*
43 RED 15 0 - 255 0% - 100% 44 GREEN 15 0 - 255 0% - 100% 45 BLUE 15 0 - 255 0% - 100% 46 RED 16 0 - 255 0% - 100% 47 GREEN 16 0 - 255 0% - 100% 48 BLUE 16 0 - 255 0% - 100%
ADJ Products, LLC - www.adj.com - Dotz Matrix User Manual Page 16 ADJ Products, LLC - www.adj.com - Dotz Matrix User Manual Page 17
Dotz Matrix 52 Channel Mode
Dotz Matrix 52 Channel Mode
Channel Value Function 49 COLOR MACROS & PROGRAMS
0 - 15 NO FUNCTION 16 - 23 RED 24 - 31 GREEN 32 - 39 BLUE 40 - 47 RED & GREEN 48 - 55 GREEN & BLUE 56 - 63 RED & BLUE 64 - 71 RED, GREEN, & BLUE 72 - 79 COLOR 1 80 - 87 COLOR 2 88 - 95 COLOR 3 96 - 103 COLOR 4 104 - 111 COLOR 5 112 - 119 COLOR 6 120 - 127 COLOR 7 128 - 135 COLOR 8 136 - 143 COLOR FADE 1 144 - 151 COLOR SNAKE 152 - 159 COLOR FADE 2 160 - 167 COLOR CHANGE 168 - 175 COLOR FLOW 1 176 - 183 COLOR FLOW 2 184 - 191 COLOR FLOW 3 192 - 199 COLOR FLOW 4 200 - 207 COLOR FLOW 5 208 - 215 COLOR FLOW 6 216 - 223 COLOR FLOW 7 216 - 223 COLOR FLOW 7 224 - 231 COLOR FLOW 8 232 - 239 COLOR FLOW 9 240 - 247 COLOR FLOW 10 248 - 255 N/G
Channel Value Function 50 MASTER DIMMER/PROGRAM SPEED
0 - 255 MASTER DIMMER 0% - 100% 0 - 255 PROGRAM SPEED SLOW - FAST 51 STROBING 0 - 255 SLOW - FAST 52 DIMMER CURVES 0 - 41 STANDARD 42 - 84 STAGE 85 - 127 TV 128 - 170 ARCHITECTURAL 171 - 213 THEATER 214 - 255 DEFAULT TO UNIT CURVE SETTING
When Channel 49 is being used between the values of 136-247, Channel 50 will control the speed of the programs.
ADJ Products, LLC - www.adj.com - Dotz Matrix User Manual Page 18
ADJ Products, LLC - www.adj.com - Dotz Matrix User Manual Page 19
Dotz Matrix Installation
Dotz Matrix Power Cord Daisy Chaining
When installing the unit, the trussing or area of installation must be able to hold 10 times the weight without any deformation. When installing the unit must be secured with a secondary safety attach­ment, e.g. and appropriate safety cable. Never stand directly below the unit when mounting, removing, or servicing the unit.
Overhead mounting requires extensive experience, including calculat­ing working load limits, installation material being used, and perodic safety inspection of all installation material and unit. If you lack these qualications, do not attempt the installation yourself.
These installaiton should be checked by a skilled person once a year.
The Dotz Matrix is fully operational in two dierent mounting posi­tions, hanging upside-down from a ceiling or set on a at level sur­face. To avoid internal damage to the unit, never mount the unit on its side as illustrated above. Be sure this xture is kept at least 0.5m away from any ammable materials (decoration etc.). Always use and install the supplied safety cable as a safety measure to prevent acci­dental damage and/or injury in the event the clamp fails. Never use
the carrying handles for secondary attachment.
With this feature you can connect the xtures to one another
using the IEC input and output sockets. The quantity that can be
connected is 5 xtures maximum. After 5 xtures you will need to use a new power outlet. They must be the same xtures. DO NOT mix xtures.
Dotz Matrix Fuse Replacement
Locate and remove the unit’s power cord. Once the cord has been removed located the fuse holder located inside the power socket. Insert a flat-head screw driver into the power socket and gently pry out the fuse holder. Remove the bad fuse and replace with a new one. The fuse holder has a built-in socket for a spare fuse be sure not to confuse the spare fuse with active fuse.
Dotz Matrix Cleaning
Due to fog residue, smoke, and dust cleaning the internal and exter­nal optical lenses must be carried out periodically to optimize light output.
1. Use a soft cloth to wipe down the outside casing.
Cleaning frequency depends on the environment in which the fixture operates (i.e. smoke, fog residue, dust, dew).
Dotz Matrix Troubleshooting
Listed below are a few common problems the user may encounter, with solutions.
Unit not responding to DMX:
1. Check that the DMX cables are connected properly and are wired correctly (pin 3 is “hot”; on some other DMX devices pin 2 may be ‘hot’). Also, check that all cables are connected to the right connectors; it does matter which way the inputs and outputs are connected.
Unit does not respond to sound:
1. Quiet or high pitched sounds will not activate the unit.
If problems are not resolved; Contact ADJ Products, LLC for service.
1-800-322-6337
ADJ Products, LLC - www.adj.com - Dotz Matrix User Manual Page 20 ADJ Products, LLC - www.adj.com - Dotz Matrix User Manual Page 21
Dotz Matrix Warranty
MANUFACTURER’S LIMITED WARRANTY
A. ADJ Products, LLC hereby warrants, to the original purchaser, ADJ Products, LLC products to be free of manufacturing defects in material and workmanship for a prescribed period from the date of purchase (see specific warranty period on reverse). This warranty shall be valid only if the product is purchased within the United States of America, including possessions and territories. It is the owner’s responsibility to establish the date and place of purchase by acceptable evidence, at the time service is sought.
B. For warranty service you must obtain a Return Authorization number (RA#) before sending back the product–please contact ADJ Products, LLC Service Department at 800-322-6337. Send the pro­ duct only to the ADJ Products, LLC factory. All shipping charges must be pre-paid. If the requested repairs or service (including parts replacement) are within the terms of this warranty, ADJ Products, LLC will pay return shipping charges only to a designated point within the United States. If the entire instru­ ment is sent, it must be shipped in it’s original package. No accessories should be shipped with the product. If any accessories are shipped with the product, ADJ Products, LLC shall have no liability whatsoever for loss of or damage to any such accessories, nor for the safe return thereof.
C. This warranty is void if the serial number has been altered or removed; if the product is modified in any manner which ADJ Products, LLC concludes, after inspection, affects the reliability of the product; if the product has been repaired or serviced by anyone other than the ADJ Products, LLC factory unless prior written authorization was issued to purchaser by ADJ Products, LLC; if the product is damaged because not properly maintained as set forth in the instruction manual.
D. This is not a service contract, and this warranty does not include maintnance, cleaning or periodic check up. During the period specified above, ADJ Products, LLC will replace defective parts at its expense with new or refurbished parts, and will absorb all expenses for warranty service and repair labor by reason of defects in material or workmanship. The sole responsibility of ADJ Products, LLC under this warranty shall be limited to the repair of the product, or replacement thereof, including parts, at the sole discretion of ADJ Products, LLC. All products covered by this warranty were manufactured after August 15, 2012, and bear indentifying marks to that effect.
E. ADJ Products, LLC reserves the right to make changes in design and/or improvements upon its products without any obligation to include these changes in any products theretofore manufactured.
Dotz Matrix Specifications
SPECIFICATIONS: Voltage: 100V~240V 50Hz/60Hz LEDs: 16 x 30W COB TRI LEDs Power Consumption: 430W Total (All LED’s @ Full) Beam Angle: 60 Degrees Fuse: 7Amp (120V) 4Amp (250V) Power Cord Daisy Chain: 5 Fixtures Max. Weight: 18lbs./ 7.8Kgs. Dimensions: 13.75” (L) x 6.75” (W) x 14.75” (H) 345 x 170 x 370mm Colors: RGB Color Mixing DMX Channels: 3 Channel Mode, 6 Channel Mode, 7 Channel Mode, 48 Channel Mode, & 52 Channel Mode Working Position: Any safe working position Warranty: 2 Year (730 days)
Auto Sensing Voltage: This xture contains a automatic volt-
age switch, which will auto sense the voltage when it is plugged into the power source.
No warranty, whether expressed or implied, is given or made with respect to any accessory supplied with products described above. Except to the extent prohibited by applicable law, all implied warranties made by ADJ Products, LLC in connection with this product, including warranties of merchantability or fitness, are limited in duration to the warranty period set forth above. And no warranties, whether expressed or implied, including warranties of merchantability or fitness, shall apply to this product after said period has expired. The consumer’s and/or Dealer’s sole remedy shall be such repair or replacement as is expressly provided above; and under no circumstances shall ADJ Products, LLC be liable for any loss or damage, direct or consequential, arising out of the use of, or inability to use, this product.
This warranty is the only written warranty applicable to ADJ Products, LLC Products and supersedes all prior warranties and written descriptions of warranty terms and conditions heretofore published.
MANUFACTURER’S LIMITED WARRANTY PERIODS:
•LightingProducts=1-year(365days)LimitedWarranty(Such as: Special Effect Lighting, Intelligent
Lighting, UV lighting, Strobes, Fog Machines, Bubble Machines, Mirror Balls, Par Cans, Trussing, Lighting Stands etc. excluding LED and lamps)
•LaserProducts=90-DayLimitedWarranty  •L.E.D.Products=2-year(730days)LimitedWarranty(excluding motors, PCB boards, and power
supplies, which have a 1-year (365 day Limited Warranty) and batteries which have a 180 day limited warranty). Only the L.E.D.s carry a 3-year warranty
ADJ Products, LLC - www.adj.com - Dotz Matrix User Manual Page 22
Please Note: Specications and improvements in the design of this unit and this manual are subject to change without any prior written notice.
ADJ Products, LLC
6122 S. Eastern Ave. Los Angeles, CA 90040 USA
Tel: 323-582-2650 / Fax: 323-725-6100
Web: www.adj.com / E-mail: info@americandj.com
A.D.J. Supply Europe B.V.
Junostraat 2
6468 EW Kerkrade
Netherlands
service@adjgroup.eu / www.adj.eu
Tel: +31 45 546 85 00 / Fax: +31 45 546 85 99
Loading...