COB CannOn Wash Pearl
©2015 ADJ Products, LLC all rights reserved. Information,
specications, diagrams, images, and instructions herein are
subject to change without notice. ADJ Products, LLC logo and
identifying product names and numbers herein are trademarks
of ADJ Products, LLC. Copyright protection claimed includes all
forms and matters of copyrightable materials and information
now allowed by statutory or judicial law or hereinafter granted.
Product names used in this document may be trademarks or
registered trademarks of their respective companies and are
hereby acknowledged. All non-ADJ Products, LLC brands and
product names are trademarks or registered trademarks of their
respective companies.
ADJ Products, LLC and all aliated companies hereby disclaim any and all liabilities for property, equipment, building,
and electrical damages, injuries to any persons, and direct or
indirect economic loss associated with the use or reliance of
any information contained within this document, and/or as a
result of the improper, unsafe, unsucient and negligent assembly, installation, rigging, and operation of this product.
11/15
User Instructions
Europe Energy Saving Notice
Energy Saving Matters (EuP 2009/125/EC)
Saving electric energy is a key to help protecting the enviroment.
Please turn o all electrical products when they are not in use. To
avoid power consumption in idle mode, disconnect all electrical
equipment from power when not in use. Thank you!
COB Cannon Wash Pearl Introduction
COB Cannon Wash Pearl Features
Unpacking:
by ADJ Products, LLC. Every COB Cannon Wash Pearl has been
thoroughly tested and has been shipped in perfect operating condition. Carefully check the shipping carton for damage that may have
occurred during shipping. If the carton appears to be damaged, carefully inspect your xture for any damage and be sure all accessories
necessary to operate the unit has arrived intact. In the case damage
has been found or parts are missing, please contact our toll free customer support number for further instructions. Do not return this unit to
your dealer without rst contacting customer support.
Introduction:
high powered LED wash fixture. This wash has five operating modes:
Sound Active mode, Auto mode, RGBA Dimmer mode, Static Color
mode, and DMX control mode. This xture can be used in a stand
alone mode or connected in a Master/Slave conguration. To optimize
the performance of this product, please read these operating instructions carefully to familiarize yourself with the basic operations of this
unit. These instructions contain important safety information regarding
the use and maintenance of this unit. Please keep this manual with the
unit, for future reference.
Customer Support: ADJ Products, LLC provides a customer support
line, to provide set up help and to answer any question should you
encounter problems during your set up or initial operation. You may
also visit us on the web at www.adj.com for any comments or suggestions. Service Hours are Monday through Friday 8:00 a.m. to 4:30 p.m.
Pacic Standard Time.
Voice: (323) 582-3322
Fax: (323) 582-3108
E-mail: support@AmericanDJ.com
Thank you for purchasing the COB Cannon Wash Pearl
The ADJ COB Cannon Wash Pearl is a DMX intelligent,
Warning! To prevent or reduce the risk of electrical shock or re, do
not expose this unit to rain or moisture.
Caution! There are no user serviceable parts inside this unit. Do not
attempt any repairs yourself, doing so will void your manufactures warranty. In the unlikely event your unit may require service please contact
ADJ Products, LLC.
PLEASE recycle the shipping carton when ever possible.
• Five Operating Modes
• Electronic Dimming 0-100%
• 5 Selectable Dimming Curves
• 64 Color Macros
• Built in Microphone
•
Opitional 40° & 50° Lenses Included
• DMX-512 protocol
• 3-Pin & 5-Pin DMX Connections
• 7 DMX Modes: 3 Channel Mode, 4 Channel Mode, 5 Channel
Mode, 6 Channel Mode, 7 Channel Mode, 9 Channel Mode, & 10
Channel Mode.
• ADJ RFC compatiable (Not Included)
• Power Cord Daisy Chain (See page 26)
COB Cannon Wash Pearl Warranty Registration
The COB Cannon Wash Pearl carries a 2 year limited warranty. Please
fill out the enclosed warranty card to validate your purchase. All
returned service items whether under warranty or not, must be freight
pre-paid and accompany a return authorization (R.A.) number. The
R.A. number must be clearly written on the outside of the return package. A brief description of the problem as well as the R.A. number
must also be written down on a piece of paper included in the shipping carton. If the unit is under warranty, you must provide a copy of
your proof of purchase invoice. You may obtain a R.A. number by contacting our customer support team on our customer support number.
All packages returned to the service department not displaying a R.A.
number on the outside of the package will be returned to the shipper.
COB Cannon Wash Pearl Installation
The unit should be mounted using a mounting clamp (not provided),
axing it to the mounting bracket that is provided with the unit.
Always ensure that the unit is rmly xed to avoid vibration and slipping while operating. Always ensure that the structure to which you
are attaching the unit is secure and is able to support a weight of 10
times the unit’s weight. Also, always use a safety cable that can hold
12 times the weight of the unit when installing the xture.
The equipment must be installed by a professional, and it must be
installed in a place where it is out of the reach of people’s grasp.
ADJ Products, LLC - www.adj.com - COB Cannon Wash Pearl User Manual Page 3ADJ Products, LLC - www.adj.com - COB Cannon Wash Pearl User Manual Page 2
COB Cannon Wash Pearl Safety Precautions
COB Cannon Wash Pearl DMX Set Up
• To reduce the risk of electrical shock or re, do not expose this unit
rain or moisture
• Do not spill water or other liquids into or on to your unit.
• Do not attempt to operate this unit if the power cord has been
frayed or broken. Do not attempt to remove or break o the ground
prong from the electrical cord. This prong is used to reduce the risk
of electrical shock and re in case of an internal short.
• Disconnect from main power before making any type of connection.
• Do not remove the cover under any conditions. There are no user
serviceable parts inside.
• Never operate this unit when it’s cover is removed.
• Never plug this unit in to a dimmer pack
• Always be sure to mount this unit in an area that will allow proper
ventilation. Allow about 6” (15cm) between this device and a wall.
• Do not attempt to operate this unit, if it becomes damaged.
• This unit is intended for indoor use only, use of this product out`
doors voids all warranties.
• During long periods of non-use, disconnect the unit’s main power.
• Always mount this unit in safe and stable matter.
• Power-supply cords should be routed so that they are not likely to
be walked on or pinched by items placed upon or against them,
paying particular attention to the point they exit from the unit.
• Cleaning -The fixture should be cleaned only as recommended by
t he manufacturer. See page 26 for cleaning details.
• Heat -The appliance should be situated away from heat sources
such as radiators, heat registers, stoves, or other appliances (inclu d ing amplifiers) that produce heat.
• The fixture should be serviced by qualified service personnel when:
A. The power-supply cord or the plug has been damaged.
B. Objects have fallen, or liquid has been spilled into the appliance.
C. The appliance has been exposed to rain or water.
D. The appliance does not appear to operate normally or exhibits a
marked change in performance.
Power Supply: The ADJ COB Cannon Wash Pearl contains a automatic
voltage switch, which will auto sense the voltage when it is plugged
into the power source. With this switch there is no need to worry about
the correct power voltage, this unit can be plugged in anywhere.
DMX-512: DMX is short for Digital Multiplex. This is a universal proto-
col used as a form of communication between intelligent fixtures and
controllers. A DMX controller sends DMX data instructions from the
controller to the fixture. DMX data is sent as serial data that travels
from fixture to fixture via the DATA “IN” and DATA “OUT” XLR terminals located on all DMX fixtures (most controllers only have a DATA
“OUT” terminal).
DMX Linking: DMX is a language allowing all makes and models of
dierent manufactures to be linked together and operate from a single
controller, as long as all xtures and the controller are DMX compliant. To ensure proper DMX data transmission, when using several
DMX fixtures try to use the shortest cable path possible. The order
in which fixtures are connected in a DMX line does not influence the
DMX addressing. For example; a fixture assigned a DMX address of 1
may be placed anywhere in a DMX line, at the beginning, at the end,
or anywhere in the middle. When a fixture is assigned a DMX address
of 1, the DMX controller knows to send DATA assigned to address 1
to that unit, no matter where it is located in the DMX chain.
Data Cable (DMX Cable) Requirements (For DMX Operation): The
COB Cannon Wash Pearl can be controlled via DMX-512 protocol. The
COB Cannon Wash Pearl has 7 DMX modes, please see pages 9-10
for the dierent modes. The DMX address is set on the back panel of
the COB Cannon Wash Pearl. Your unit and your DMX controller require
a standard 3-pin or 5-pin XLR connector for data
input and data output (Figure 1). We recommend
Accu-Cable DMX cables. If you are making your
own cables, be sure to use standard 110-120 Ohm
shielded cable (This cable may be purchased at
almost all pro lighting stores). Your cables should
be made with a male and female XLR connector
on either end of the cable. Also remember that
DMX cable must be daisy chained and cannot be
Figure 1
split.
ADJ Products, LLC - www.adj.com - COB Cannon Wash Pearl User Manual Page 4
ADJ Products, LLC - www.adj.com - COB Cannon Wash Pearl User Manual Page 5
COB Cannon Wash Pearl DMX Set Up
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
DMX512
DMX+,DMX-,COMMON
1
2
3
Termination reduces signal errors and
avoids signal transmission problems
and interference. It is always advisable
to connect a DMX terminal, (Resistance
120 Ohm 1/4 W) between PIN 2 (DMX-)
and PIN 3 (DMX +) of the last fixture.
POWER
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
and PIN 3 (DMX +) of the last fixture.
COB Cannon Wash Pearl Operating Instructions
Notice: Be sure to follow gures two and three when making your own
cables. Do not use the ground lug on the XLR connector. Do not connect the cable’s shield conductor to the ground lug or allow the shield
conductor to come in contact with the XLR’s outer casing. Grounding
the shield could cause a short circuit and erratic behavior.
COMMON
1
DMX512 IN
3
3-PIN XLR
2
Figure 2
XLR Pin Conguration
1 Ground
3 Hot
Pin 1 = Ground
Pin 2 = Data Compliment (negative)
Pin 3 = Data True (positive)
When longer runs of cable are
Figure 4
Pin 1
Pin 2
Pin 3
Do Not Use
Do Not Use
XLR Male Socket
1 Ground
DMX512 OT
3-PIN XLR
2 Cold
3 Hot
1
3
2
DMX +
DMX -
XLR Female Socket
2 Cold
Figure 3
Special Note: Line Termination.
used, you may need to use a terminator on the last unit to avoid erratic
behavior. A terminator is a 110-120 ohm 1/4 watt resistor which is connected between pins 2 and 3 of a male XLR connector (DATA + and
DATA -). This unit is inserted in the female XLR connector of the last
unit in your daisy chain to terminate the line. Using a cable terminator
(ADJ part number Z-DMX/T) will decrease the possibilities of erratic
behavior.
5-Pin XLR DMX Connectors.
512 data cables for DATA transmission in place of 3-pin. 5-pin DMX
xtures may be implemented in a 3-pin DMX line. When inserting standard 5-pin data cables in to a 3-pin line a cable adaptor must be used,
these adaptors are readily available at most electric stores. The chart
below details a proper cable conversion.
Conductor 5-Pin XLR Male (In)3-Pin XLR Female (Out)
Ground/Shield
Data Compliment (- signal)
Data True (+ signal)
Not Used
Not Used
ADJ Products, LLC - www.adj.com - COB Cannon Wash Pearl User Manual Page 6
Termination reduces signal errors and
1
avoids signal transmission problems
3
and interference. It is always advisable
2
to connect a DMX terminal, (Resistance
120 Ohm 1/4 W) between PIN 2 (DMX-)
Some manufactures use 5-pin DMX-
3-Pin XLR to 5-Pin XLR Conversion
Pin 1
Pin 2
Pin 3
System Menu: The display will lock after 30 seconds, press
the MODE button for 3 seconds to unlock.
LED Display On/Off:
To set the LED display to turn off after 10 seconds, press the MODE
button until “don” is displayed, press the UP button to display “doff”.
Now the display will disappear after 10s. Press any button to turn
the display on again. Be advised though that the display will turn off
automatically after 10 seconds.
To set the display press the MODE button until “dXX” is displayed.
Use the UP or DOWN buttons to select either:
“don” = LED display on at all times.
“doFF” = LED display shuts off after 10 seconds.
LED Display Inversion:
Follow these instructions to flip the display 180° so that the display
can be read upside down.
1. Plug the fixture in and press the MODE button until “dXX” is dis-
played. “XX” represents either “on” or “oFF”.
2. Press the SET UP button until “Stnd” is displayed.
3. Press the UP or DOWN buttons to reverse the display 180°.
Operating Modes:
The COB Cannon Wash Pearl has five operating modes:
• RGBA Dimmer Mode - Choose one of the four colors to remain
static or adjust the intensity of each color to make your desired
color.
• Sound-Active mode - The unit will react to sound, chasing through
the built in programs. There are 16 sound active modes.
• Auto Mode - There are 3 Auto Modes to choose from.
• Static Color Mode - There are 64 colors to choose from.
• DMX control mode - This function will allow you to control each
individual fixtures traits with a standard DMX 512 controller.
RGBA Dimmer Mode:
1. Plug the fixture in and press the MODE button until:
2. When “r.XXX” is displayed you are in Red dimming mode. Press
the UP and DOWN buttons to adjust intensity.
ADJ Products, LLC - www.adj.com - COB Cannon Wash Pearl User Manual Page 7
COB Cannon Wash Pearl Operating Instructions
COB Cannon Wash Pearl Operating Instructions
3. When “G.XXX” is displayed you are in Green dimming mode.
Press the UP and DOWN buttons to adjust intensity.
4. When “b.XXX” is displayed you are in Blue dimming mode. Press
the UP and DOWN buttons to adjust intensity.
5. When “A.XXX” is displayed you are in Amber dimming mode.
Press the UP and DOWN buttons to adjust intensity.
6. After you have adjusted the RGBA colors to make your desired
color you can then activate strobing by pressing the SET UP but ton to enter the Flash (strobe) mode.
7. “FS.XX” will be displayed, this is Flash mode. The Flash can be
adjusted between “FS.00” (flash off) to “FS.15” (fastest flash).
Sound Active Mode:
In this mode the COB Cannon Wash Pearl will react to sound, and
chase through the different colors.
1. Plug the fixture in and press the MODE button until “SoXX” is dis played. “XX” represents the sound active mode (1-16) currently
displayed.
2. The fixture will now change via sound.
3. Press the SET UP button to adjust the sound sensitivity. “SJ-X”
should be displayed. Use the UP or DOWN buttons to adjust the
sensitivity. “SJ-1” is the lowest sensitivity, “SJ-8” is the highest.
Auto Run Mode:
There are 3 types of Auto Run Modes to choose from; Color
Color Change, and both modes running together.
is adjustable in all 3 modes.
1. Plug the fixture in and press the MODE button until either “AFXX”,
“AJXX”, or “A-JF” is displayed.
• AFXX = Color Fade mode, there are 16 Color Fade modes to
choose from. Use the UP or DOWN buttons to scroll through the
different Auto Fade modes.
• AJXX = Color Change mode, there are 16 Color Change modes to
choose from. Use the UP or DOWN buttons to scroll through the
different Auto Change modes.
• A-JF = Both Color Fade and Color Change modes running.
2. After you have chosen your desired running mode press the SET
UP button until “SP.XX” is displayed. When this is displayed you
can adjust the running speed of your desired program. Use the
The running
Fade,
speed
UP or DOWN button to adjust the speed between “SP.01” (slow est) and “SP.16” (fastest). Once you have set your desired running
speed, press the SET UP button to return to your desired Auto
Run Mode.
Static Color Mode:
1. Plug the fixture in and press the MODE button until “CLXX” is dis-
played.
2. There are 64 colors to choose from. Select your desired color by
pressing the UP and DOWN buttons. After you have selected your
desired color you can activate strobing by pressing the SET UP
button to enter the Flash (strobe) mode.
3. “FS.XX” will be displayed, this is Flash mode. The Flash can be
adjusted between “FS.00” (flash off) to “FS.15” (fastest flash).
DMX Mode:
Operating through a DMX controller gives the user the freedom to
create their own programs tailored to their own individual needs. This
function also allows you to use your fixtures as spot lights. The COB
Cannon Wash Pearl has 7 DMX modes: 3 channel mode, 4 channel
mode, 5 channel mode, 6 channel mode, 7 channel mode, 9 channel
mode, and a 10 channel mode. See page’s 14-22 for each mode’s
DMX traits.
1. This function will allow you to control each individual fixture’s
traits with a standard DMX 512 controller.
2. To run your fixture in DMX mode press the MODE button until
“d.XXX” is displayed. “XXX” represents the current displayed DMX
address. Use the UP or DOWN buttons to select your desired
DMX address, then press the SETUP button to select your DMX
Channel mode.
3. Use the UP or DOWN buttons to scroll through the DMX Channel
modes. The Channel modes are listed below:
• To run the 3 Channel Mode, press the MODE button until “Ch03”
is displayed. This is the 3 Channel DMX Mode.
• To run the 4 Channel Mode, press the MODE button until “Ch04”
is displayed. This is the 4 Channel DMX Mode.
• To run the 5 Channel Mode, press the MODE button until “Ch05”
is displayed. This is the 5 Channel DMX Mode.
• To run the 6 Channel Mode, press the MODE button until “Ch06”
ADJ Products, LLC - www.adj.com - COB Cannon Wash Pearl User Manual Page 9ADJ Products, LLC - www.adj.com - COB Cannon Wash Pearl User Manual Page 8
COB Cannon Wash Pearl Operating Instructions
COB Cannon Wash Pearl Operating Instructions
is displayed. This is the 6 Channel DMX Mode.
• To run the 7 Channel Mode, press the MODE button until “Ch07”
is displayed. This is the 7 Channel DMX Mode.
• To run the 9 Channel Mode, press the MODE button until “Ch09”
is displayed. This is the 9 Channel DMX Mode.
• To run the 10 Channel Mode, press the MODE button until “Ch10”
is displayed. This is the 10 Channel DMX Mode.
4. Please see pages 14-22 for DMX values and traits.
5. After you have chosen your desired DMX Channel mode plug in
the fixture via the XLR connections to any standard DMX control-
ler.
Default Running Mode:
This is a default running mode. When this mode is activated all modes
will return to their default settings.
1. Plug the fixture in and press the MODE button until “dXX” is dis-
played. “XX” represents either “on” or “oFF”.
2. Press the SET UP button until “dEFA” is displayed.
3. Press the UP and DOWN buttons simultaneously. Press the
MODE button to exit.
DMX State:
This mode can be used as a precaution mode, that in case the DMX
signal is lost, the operating mode chosen in the setup is the running
mode the xture will go into when the DMX signal is lost. You can also
set this as the operating mode you would like the unit to return to when
power is applied.
1. Plug the fixture in and press the MODE button until “d.XXX” is dis-
played. “XXX” represents the current displayed DMX address.
2. Press the SET UP button so that “nodn” is displayed. Use the UP
and DOWN buttons to scroll through the DMX states.
• “bLAC” (Blackout) - If the DMX signal is lost or interrupted,
the unit will automatically go into stand by mode.
• “LASt” (Last State) - If the DMX signal is lost or interrupted,
the xture will stay in the last DMX set up. If power is applied and
this mode is set, the unit will automatically go into the last DMX set
up.
• “ProG” (Auto Run) - If the DMX signal is lost or interrupted,
the unit will automatically go into Auto Run mode.
3. Use the UP and DOWN buttons to nd your desired DMX state
and press SET UP to conrm and exit.
Dimmer Curve:
This is used to set the dimming curve used with DMX mode. See
page 27 for the dimming curves chart.
1. Plug the fixture in and press the MODE button until “d.XXX” is dis-
played. “XXX” represents the current displayed DMX address.
2. Press the SET UP button until “dr-X” is displayed. “X” represents
the displayed dimmer curve (0-4).
• 0 - Standard
• 1 - Stage
• 2 - TV
• 3 - Architectural
• 4 - Theatre
3. Press the UP or DOWN buttons to scroll through and select your
desired dimming curve.
ADJ RFC:
This function is used to activate and deactivate the ADJ RFC (Remote
Control). When this function is activated you can control the fixture
using the ADJ RFC. Please see the next page for ADJ RFC controls
and functions.
1. Plug the fixture in and press the MODE button until “dXX” is dis-
played. “XX” represents either “on” or “oFF”.
2. Press the SET UP button until “rFXX” is displayed. “XX” repre-
sents either “on” or “oF”.
3. Press the UP or DOWN buttons to either activate the remote func tion (On) or deactivate it (Off).
ADJ Products, LLC - www.adj.com - COB Cannon Wash Pearl User Manual Page 10 ADJ Products, LLC - www.adj.com - COB Cannon Wash Pearl User Manual Page 11
COB Cannon Wash Pearl Master-Slave Configuration
COB Cannon Wash Pearl ADJ RFC Operation
This function will allows you to link units together to run in a MasterSlave mode. In a Master-Slave set up one unit will act as the control-
ling unit and the others will react to the controlling units built-in programs. Any unit can act as a Master or as a Slave however, only one
unit can be programmed to act as the “Master.”
Master-Slave Connections and Settings:
1. Daisy chain your units via the XLR connector on the rear of
the unit. Use standard XLR data cables to link your units together.
Remember that the Male XLR connector is the input and the
Female XLR connector is the ouput. The first unit in the chain
(master) will use the female XLR connector only. The last unit in
the chain will use the male XLR connector only.
2. Set the “Master” unit to your desired mode of operation.
3. On the “Slave” units press the MODE button until “SLAu” is dis played. Each “Slave” unit must be set to the same setting.
4. Connect the rst “Slave” unit to the “Master.” The “Slave” unit(s)
should now start following the “Master” unit.
The ADJ RFC remote (sold seperately) has many different functions and
allows you to control your COB Cannon Wash Pearl from long distance.
The ADJ RFC remote can control your system up to 150 ft. To use the
RFC you must first activate the fixtures receiver, to activate the receiver
please see the instructions on page 11.
BLACKOUT - Pressing this button will blackout the fixture. Press this
button for more then 3 seconds to activate default mode. All modes will
return to their default settings.
AUTO RUN - This button lets you cycle through color fade mode, color
change mode, and auto run mode. Each press of the button will change
to the next mode. Color fade mode and color change mode have 16 different programs. You can use the “+” and “-” buttons to cycle through
the 16 programs. You can control the speeds of each mode by pressing
the SPEED button and then using the “+” and “-” buttons to adjust the
speed.
SELECTION PROGRAM -
mode. Use the “+” and “-” buttons to scroll through the 64 colors. Once
you have found your desired color press the FLASH button to activate
strobing. Use the “+” and “-” buttons adjust the strobe speed.
FLASH - This button will activate the flash (strobe) effect. You can con-
trol the flash speed by pressing the “+” and “-” buttons.
Press this button to activate Static Color
SPEED - Press this button and use the “+” & “-” buttons to adjust the
speed of the color fade mode, color change mode, and auto run.
SOUND ACTIVE - This button activates sound active mode. Use the “+”
& “-” buttons to scroll through the 16 sound active modes and find your
desired mode. Press the SOUND ACTIVE button again to access sound
sensitivity adjustment. Use the “+” & “-” buttons to adjust the sound sen-
sitivity level.
R G B W/A - Press either one of these buttons and the press the “+” or
“-” to adjust the brightness. Press the Flash button to activate strobing
and use the “+” or “-” buttons to adjust the strobe speed.
“+” and “-” - These buttons are used to adjust the flash rate, auto run
speed, color fade speed, color change speed, sound sensitivity, and
output intensity. These buttons are also used to scroll through the static
colors, color fade programs, color change programs, and sound active
programs.
ADJ Products, LLC - www.adj.com - COB Cannon Wash Pearl User Manual Page 12 ADJ Products, LLC - www.adj.com - COB Cannon Wash Pearl User Manual Page 13
COB Cannon Wash Pearl 3 Channel Mode
COB Cannon Wash Pearl 5 Channel Mode
Channel Value Function
1 0 - 255 COLOR MACROS
See page 23 for the Color Macro Chart
2 SHUTTER/STROBE
0 - 31 LED OFF
32 - 63 LED ON
64 - 95 STROBING SLOW - FAST
96 - 127 LED ON
128 - 159 STROBE PULSE SLOW - FAST
160 - 191 LED ON
192 - 223 RANDOM STROBE SLOW - FAST
224 - 255 LED ON
3 MASTER DIMMER
0 - 255 0% - 100%
COB Cannon Wash Pearl 4 Channel Mode
Channel Value Function
1 RED
0 - 255 0% - 100%
2 GREEN
0 - 255 0% - 100%
3 BLUE
0 - 255 0% - 100%
4 AMBER
0 - 255 0% - 100%
Channel Value Function
1 RED
0 - 255 0% - 100%
2 GREEN
0 - 255 0% - 100%
3 BLUE
0 - 255 0% - 100%
4 AMBER
0 - 255 0% - 100%
5 MASTER DIMMER
0 - 255 0% - 100%
COB Cannon Wash Pearl 6 Channel Mode
Channel Value Function
1 RED
0 - 255 0% - 100%
2 GREEN
0 - 255 0% - 100%
3 BLUE
0 - 255 0% - 100%
4 AMBER
0 - 255 0% - 100%
5 SHUTTER/STROBE
0 - 31 LED OFF
32 - 63 LED ON
64 - 95 STROBING SLOW - FAST
96 - 127 LED ON
128 - 159 STROBE PULSE SLOW - FAST
160 - 191 LED ON
192 - 223 RANDOM STROBE SLOW - FAST
224 - 255 LED ON
6 MASTER DIMMER
0 - 255 0% - 100%
ADJ Products, LLC - www.adj.com - COB Cannon Wash Pearl User Manual Page 14 ADJ Products, LLC - www.adj.com - COB Cannon Wash Pearl User Manual Page 15
COB Cannon Wash Pearl 7 Channel Mode COB Cannon Wash Pearl 9 Channel Mode
Channel Value Function
1 RED
0 - 255 0% - 100%
2 GREEN
0 - 255 0% - 100%
3 BLUE
0 - 255 0% - 100%
4 AMBER
0 - 255 0% - 100%
5 SHUTTER/STROBE
0 - 31 LED OFF
32 - 63 LED ON
64 - 95 STROBING SLOW - FAST
96 - 127 LED ON
128 - 159 STROBE PULSE SLOW - FAST
160 - 191 LED ON
192 - 223 RANDOM STROBE SLOW - FAST
224 - 255 LED ON
6 MASTER DIMMER
0 - 255 0% - 100%
7 DIMMER CURVES
0 - 20 STANDARD
21 - 40 STAGE
41 - 60 TV
61 - 80 ARCHITECTURAL
81 - 100 THEATRE
101 - 255 DEFAULT TO UNIT SETTING
Channel Value Function
1 RED
0 - 255 0% - 100%
2 GREEN
0 - 255 0% - 100%
3 BLUE
0 - 255 0% - 100%
4 AMBER
0 - 255 0% - 100%
5 SHUTTER/STROBE
0 - 31 LED OFF
32 - 63 LED ON
64 - 95 STROBING SLOW - FAST
96 - 127 LED ON
128 - 159 STROBE PULSE SLOW - FAST
160 - 191 LED ON
192 - 223 RANDOM STROBE SLOW - FAST
224 - 255 LED ON
6 MASTER DIMMER
0 - 255 0% - 100%
7 PROGRAM SELECTION MODE
0 - 51 DIMMING MODE
52 - 102 COLOR MACRO MODE
103 - 153 COLOR CHANGE MODE
154 - 204 COLOR FADE MODE
205 - 255 SOUND ACTIVE MODE
8 COLOR MACROS/PROGRAMS/
SOUND ACTIVITY
0 - 255 COLOR MACRO MODE
(See page 23 for the Color Macro Chart)
COLOR CHANGE PROGRAMS
0 - 15 COLOR CHANGE 1
16 - 31 COLOR CHANGE 2
32 - 47 COLOR CHANGE 3
ADJ Products, LLC - www.adj.com - COB Cannon Wash Pearl User Manual Page 16 ADJ Products, LLC - www.adj.com - COB Cannon Wash Pearl User Manual Page 17
COB Cannon Wash Pearl 9 Channel Mode
COB Cannon Wash Pearl 9 Channel Mode
Channel Value Function
8 COLOR MACROS/PROGRAMS/
SOUND ACTIVITIY
COLOR CHANGE PROGRAMS
48 - 63 COLOR CHANGE 4
64 - 79 COLOR CHANGE 5
80 - 95 COLOR CHANGE 6
96 - 111 COLOR CHANGE 7
112 - 127 COLOR CHANGE 8
128 - 143 COLOR CHANGE 9
144 - 159 COLOR CHANGE 10
160 - 175 COLOR CHANGE 11
176 - 191 COLOR CHANGE 12
192 - 207 COLOR CHANGE 13
208 - 223 COLOR CHANGE 14
224 - 239 COLOR CHANGE 15
240 - 255 COLOR CHANGE 16
COLOR FADE PROGRAMS
0 - 15 COLOR FADE 1
16 - 31 COLOR FADE 2
32 - 47 COLOR FADE 3
48 - 63 COLOR FADE 4
64 - 79 COLOR FADE 5
80 - 95 COLOR FADE 6
96 - 111 COLOR FADE 7
112 - 127 COLOR FADE 8
128 - 143 COLOR FADE 9
144 - 159 COLOR FADE 10
160 - 175 COLOR FADE 11
176 - 191 COLOR FADE 12
192 - 207 COLOR FADE 13
208 - 223 COLOR FADE 14
Channel Value Function
8 COLOR MACROS/PROGRAMS/
SOUND ACTIVITY
SOUND ACTIVE PROGRAMS
0 - 15 SOUND ACTIVE MODE 1
16 - 31 SOUND ACTIVE MODE 2
32 - 47 SOUND ACTIVE MODE 3
48 - 63 SOUND ACTIVE MODE 4
64 - 79 SOUND ACTIVE MODE 5
80 - 95 SOUND ACTIVE MODE 6
96 - 111 SOUND ACTIVE MODE 7
112 - 127 SOUND ACTIVE MODE 8
128 - 143 SOUND ACTIVE MODE 9
144 - 159 SOUND ACTIVE MODE 10
160 - 175 SOUND ACTIVE MODE 11
176 - 191 SOUND ACTIVE MODE 12
192 - 207 SOUND ACTIVE MODE 13
208 - 223 SOUND ACTIVE MODE 14
224 - 239 SOUND ACTIVE MODE 15
240 - 255 SOUND ACTIVE MODE 16
9 PROGRAM SPEED/SOUND SENSITIVE
0 - 255 SLOW - FAST
0 - 255 LEAST SENSITIVE - MOST SENSITIVE
When Channel 7 is between the values of 0-51, Channels 1-4 are used, and
Channel 5 will control strobing.
When Channel 7 is between the values of 52-102, Channel 8 is in Color Macros
Mode, and Channel 5 will control strobing.
When Channel 7 is between the values of 103-153, Channel 8 is in Color Change
Mode, and Channel 9 will control the color change speed.
When Channel 7 is between the values of 154-204, Channel 8 is in Color Fade
Mode, and Channel 9 will control the color fade speed.
When Channel 7 is between the values of 205-255, Channel 8 is in Sound Active
Mode, and Channel 9 will control the sound sensitivity.
224 - 239 COLOR FADE 15
240 - 255 COLOR FADE 16
ADJ Products, LLC - www.adj.com - COB Cannon Wash Pearl User Manual Page 18 ADJ Products, LLC - www.adj.com - COB Cannon Wash Pearl User Manual Page 19
COB Cannon Wash Pearl 10 Channel Mode
COB Cannon Wash Pearl 10 Channel Mode
Channel Value Function
1 RED
0 - 255 0% - 100%
2 GREEN
0 - 255 0% - 100%
3 BLUE
0 - 255 0% - 100%
4 AMBER
0 - 255 0% - 100%
5 SHUTTER/STROBE
0 - 31 LED OFF
32 - 63 LED ON
64 - 95 STROBING SLOW - FAST
96 - 127 LED ON
128 - 159 STROBE PULSE SLOW - FAST
160 - 191 LED ON
192 - 223 RANDOM STROBE SLOW - FAST
Channel Value Function
8 COLOR MACROS/PROGRAMS/
SOUND ACTIVITIY
COLOR CHANGE PROGRAMS
48 - 63 COLOR CHANGE 4
64 - 79 COLOR CHANGE 5
80 - 95 COLOR CHANGE 6
96 - 111 COLOR CHANGE 7
112 - 127 COLOR CHANGE 8
128 - 143 COLOR CHANGE 9
144 - 159 COLOR CHANGE 10
160 - 175 COLOR CHANGE 11
176 - 191 COLOR CHANGE 12
192 - 207 COLOR CHANGE 13
208 - 223 COLOR CHANGE 14
224 - 239 COLOR CHANGE 15
240 - 255 COLOR CHANGE 16
224 - 255 LED ON
6 MASTER DIMMER
0 - 255 0% - 100%
7 PROGRAM SELECTION MODE
0 - 51 DIMMING MODE
52 - 102 COLOR MACRO MODE
103 - 153 COLOR CHANGE MODE
154 - 204 COLOR FADE MODE
205 - 255 SOUND ACTIVE MODE
8 COLOR MACROS/PROGRAMS/
SOUND ACTIVITY
COLOR FADE PROGRAMS
0 - 15 COLOR FADE 1
16 - 31 COLOR FADE 2
32 - 47 COLOR FADE 3
48 - 63 COLOR FADE 4
64 - 79 COLOR FADE 5
80 - 95 COLOR FADE 6
96 - 111 COLOR FADE 7
112 - 127 COLOR FADE 8
128 - 143 COLOR FADE 9
144 - 159 COLOR FADE 10
0 - 255 COLOR MACRO MODE
(See page 23 for the Color Macro Chart)
COLOR CHANGE PROGRAMS
0 - 15 COLOR CHANGE 1
16 - 31 COLOR CHANGE 2
32 - 47 COLOR CHANGE 3
ADJ Products, LLC - www.adj.com - COB Cannon Wash Pearl User Manual Page 20 ADJ Products, LLC - www.adj.com - COB Cannon Wash Pearl User Manual Page 21
160 - 175 COLOR FADE 11
176 - 191 COLOR FADE 12
192 - 207 COLOR FADE 13
208 - 223 COLOR FADE 14
224 - 239 COLOR FADE 15
240 - 255 COLOR FADE 16
COB Cannon Wash Pearl 10 Channel Mode COB Cannon Wash Pearl Color Macro Chart
Channel Value Function
8 COLOR MACROS/PROGRAMS/
SOUND ACTIVITY
SOUND ACTIVE PROGRAMS
0 - 15 SOUND ACTIVE MODE 1
16 - 31 SOUND ACTIVE MODE 2
32 - 47 SOUND ACTIVE MODE 3
48 - 63 SOUND ACTIVE MODE 4
64 - 79 SOUND ACTIVE MODE 5
RGBA COLOR INTENSITY
80 - 95 SOUND ACTIVE MODE 6
96 - 111 SOUND ACTIVE MODE 7
112 - 127 SOUND ACTIVE MODE 8
128 - 143 SOUND ACTIVE MODE 9
VAULE
144 - 159 SOUND ACTIVE MODE 10
160 - 175 SOUND ACTIVE MODE 11
176 - 191 SOUND ACTIVE MODE 12
192 - 207 SOUND ACTIVE MODE 13
208 - 223 SOUND ACTIVE MODE 14
224 - 239 SOUND ACTIVE MODE 15
240 - 255 SOUND ACTIVE MODE 16
9 PROGRAM SPEED/SOUND SENSITIVE
0 - 255 SLOW - FAST
0 - 255 LEAST SENSITIVE - MOST SENSITIVE
10 DIMMER CURVES
RGBA COLOR INTENSITY Color No. DMX
0 - 20 STANDARD
21 - 40 STAGE
RED GREEN BLUE AMBER RED GREEN B LUE AMBER
41 - 60 TV
61 - 80 ARCHITECTURAL
81 - 100 THEATRE
VAULE
101 - 255 DEFAULT TO UNIT SETTING
Color No. DMX
OFF 0 0 0 0 0 Color33 129-132 255 206 143 0
Color1 1-4 80 255 234 80 Color34 133-136 254 177 153 0
Color2 5-8 80 255 164 80 Color35 137-140 254 192 138 0
Color3 9-12 77 255 112 77 Color36 141-144 254 165 98 0
Color4 13-16 117 255 83 83 Color37 145-148 254 121 0 0
Color5 17-20 160 255 77 77 Color38 149-152 176 17 0 0
Color6 21-24 223 255 83 83 Color39 153-156 96 0 11 0
Color7 25-28 255 243 77 77 Color40 157-160 234 139 171 0
Color8 29-32 255 200 74 74 Color41 161-164 224 5 97 0
Color9 33-36 255 166 77 77 Color42 165-168 175 77 173 0
Color10 37-40 255 125 74 74 Color43 169-172 119 130 199 0
Color11 41-44 255 97 77 74 Color44 173-176 147 164 212 0
Color12 45-48 255 71 77 71 Color45 177-180 88 2 163 0
Color13 49-52 255 83 134 83 Color46 181-184 0 38 86 0
Color14 53-56 255 93 182 93 Color47 185-188 0 142 208 0
Color15 57-60 255 96 236 96 Color48 189-192 52 148 209 0
Color16 61-64 238 93 255 93 Color49 193- 196 1 134 201 0
Color17 65-68 196 87 255 87 Color50 197-200 0 145 212 0
Color18 69-72 150 90 255 90 Color51 201-204 0 121 192 0
Color19 73-76 100 77 255 77 Color52 205-208 0 129 184 0
Color20 77-80 77 100 255 7 7 Color 53 209-212 0 83 115 0
Color21 81-84 67 148 255 67 Color5 4 213-216 0 97 166 0
Color22 85-88 77 195 255 77 Color5 5 217-220 1 100 167 0
Color23 89-92 77 234 255 77 Color5 6 221-224 0 40 86 0
Color24 93-96 158 255 144 144 Color57 225-228 209 219 182 0
Color25 97-100 255 251 153 153 Color58 229-232 42 165 85 0
Color26 101- 104 255 175 147 147 Color59 233-236 0 46 35 0
Color27 105- 108 255 138 186 138 Color60 237-240 8 107 222 0
Color28 109- 112 255 147 251 147 Color61 241-244 107 156 231 0
Color29 113-116 151 138 255 138 Color62 245-248 165 198 247 0
Color30 117- 120 151 138 255 138 Color 63 249-252 0 0 189 0
ADJ Products, LLC - www.adj.com - COB Cannon Wash Pearl User Manual Page 22 ADJ Products, LLC - www.adj.com - COB Cannon Wash Pearl User Manual Page 23
Color31 121- 124 138 169 255 138 Color 64 253-255 255 255 255 0
Color32 125- 128 255 255 255 255
COB Cannon Wash Pearl Photometric Chart COB Cannon Wash Pearl Optional Lens Change
The COB Cannon Wash Pearl comes with a 80 degree lens already
attached. Included in the box are optional 40 & 50 degree lenses.
To switch lenses simply remove the retainer ring located in front
front of the current lens. After the retainer ring has been removed
carefully remove the lens, and attach your desired lens. Reinstall
the retainer ring and the switch is complete. When reinstalling the
retainer ring, make sure to insert 3 points of the retainer ring into
the 3 notches located around the inside of the lens frame.
COB Cannon Wash Pearl Dimmer Curve Chart
Ramp Effect
Standard
Stage
TV
Architectural
Theatre
ADJ Products, LLC - www.adj.com - COB Cannon Wash Pearl User Manual Page 24 ADJ Products, LLC - www.adj.com - COB Cannon Wash Pearl User Manual Page 25
(Fade Time) (Fade Time)
COB Cannon Wash Pearl Power Cord Daisy Chain
With this feature you can connect the xtures to one another
using the PowerCON input and output sockets. The quantity that
can be connected is 5 xtures maximum. After 5 xtures you will
need to use a new power outlet. They must be the same xtures.
DO NOT mix xtures.
COB Cannon Wash Pearl Fuse Replacement
Disconnect the unit from its power source. Remove the power cord
from the unit. Once the cord has been removed, the fuse holder is
located next to the powerCON connection. Use a phillips head screwdriver to remove the fuse holder. Remove the fuse located inside the
fuse holder and replace with the new fuse. Install the fuse holder and
new fuse and secure it.
COB Cannon Wash Pearl Trouble Shooting
Listed below are a few common problems the user may encounter,
with solutions.
Unit not responding to DMX:
1. Check that the DMX cables are connected properly and are
wired correctly (pin 3 is “hot”; on some other DMX devices
pin 2 may be ‘hot’). Also, check that all cables are connected
to the right connectors; it does matter which way the inputs
and outputs are connected.
Unit does not respond to sound:
1. Quiet or high pitched sounds will not activate the unit.
2. Make sure that Sound Active mode is activated.
COB Cannon Wash Pearl Cleaning
Due to fog residue, smoke, and dust cleaning the internal and external optical lenses must be carried out periodically to optimize light
output.
1. Use normal glass cleaner and a soft cloth to wipe down the
outside casing.
2. Clean the external optics with glass cleaner and a soft cloth
every 20 days.
3. Always be sure to dry all parts completely before plugging
the unit back in.
Cleaning frequency depends on the environment in which the fixture
operates (i.e. smoke, fog residue, dust, dew).
ADJ Products, LLC - www.adj.com - COB Cannon Wash Pearl User Manual Page 26
COB Cannon Wash Pearl Warranty
MANUFACTURER’S LIMITED WARRANTY
A. ADJ Products, LLC hereby warrants, to the original purchaser, ADJ Products, LLC products
to be free of manufacturing defects in material and workmanship for a prescribed period from
the date of purchase (see specific warranty period on reverse). This warranty shall be valid only if the
product is purchased within the United States of America, including possessions and
territories. It is the owner’s responsibility to establish the date and place of purchase by acceptable
evidence, at the time service is sought.
B. For warranty service you must obtain a Return Authorization number (RA#)
before sending back the product–please contact ADJ Products, LLC Service Department
at 800-322-6337. Send the product only to the ADJ Products, LLC factory. All
shipping charges must be pre-paid. If the requested repairs or service (including
parts replacement) are within the terms of this warranty, ADJ Products, LLC will pay return
shipping charges only to a designated point within the United States. If the entire instrument is
sent, it must be shipped in it’s original package. No accessories should be shipped with the product. If
any accessories are shipped with the product, ADJ Products, LLC shall have no liability whatsoever for
loss of or damage to any such accessories, nor for the safe return thereof.
C. This warranty is void if the serial number has been altered or removed; if the product is modified in any
manner which ADJ Products, LLC concludes, after inspection, affects the reliability of the product; if the
product has been repaired or serviced by anyone other than the ADJ Products, LLC factory unless prior
written authorization was issued to purchaser by ADJ Products, LLC; if the product is damaged because
not properly maintained as set forth in the instruction manual.
D. This is not a service contract, and this warranty does not include maintnance, cleaning or periodic check
up. During the period specified above, ADJ Products, LLC will replace defective parts at its expense
with new or refurbished parts, and will absorb all expenses for warranty service and repair labor by
reason of defects in material or workmanship. The sole responsibility of ADJ Products, LLC under this
warranty shall be limited to the repair of the product, or replacement thereof, including parts, at the sole
discretion of ADJ Products, LLC. All products covered by this warranty were manufactured after August
15, 2012, and bear indentifying marks to that effect.
E. ADJ Products, LLC reserves the right to make changes in design and/or improvements upon its products
without any obligation to include these changes in any products theretofore manufactured.
No warranty, whether expressed or implied, is given or made with respect to any accessory supplied with
products described above. Except to the extent prohibited by applicable law, all implied warranties made
by ADJ Products, LLC in connection with this product, including warranties of merchantability or fitness,
are limited in duration to the warranty period set forth above. And no warranties, whether expressed or
implied, including warranties of merchantability or fitness, shall apply to this product after said period
has expired. The consumer’s and/or Dealer’s sole remedy shall be such repair or replacement as is
expressly provided above; and under no circumstances shall ADJ Products, LLC be liable for any loss or
damage, direct or consequential, arising out of the use of, or inability to use, this product.
This warranty is the only written warranty applicable to ADJ Products, LLC Products and
supersedes all prior warranties and written descriptions of warranty terms and conditions heretofore
published.
MANUFACTURER’S LIMITED WARRANTY PERIODS:
•LightingProducts=1-year(365days)LimitedWarranty(Such as: Special Effect Lighting, Intelligent
Lighting, UV lighting, Strobes, Fog Machines, Bubble Machines, Mirror Balls, Par Cans, Trussing,
Lighting Stands etc. excluding LED and lamps)
•LaserProducts=1Year(365Days)LimitedWarranty(excluding laser diodes which have a 6 month
limited warranty)
•L.E.D.Products=2-year(730days)LimitedWarranty(excluding motors, PCB boards, and power
supplies, which have a 1-year (365 day Limited Warranty) batteries which have a 180 day limited war-
ranty). Only the L.E.D.s carry a 2-year warranty (excluding StarTec Series which a carries a 90 Day
Limited Warranty)
•ADJDMXControllers=2Year(730Days)LimitedWarranty(excluding faders and tact switches)
ADJ Products, LLC - www.adj.com - COB Cannon Wash Pearl User Manual Page 27
COB Cannon Wash Pearl Notes COB Cannon Wash Pearl Notes
ADJ Products, LLC - www.adj.com - COB Cannon Wash Pearl User Manual Page 28
ADJ Products, LLC - www.adj.com - COB Cannon Wash Pearl User Manual Page 29
COB Cannon Wash Pearl Specifications
Model:
Voltage: 100V ~ 240V/50~60Hz
LEDs: 1 x 150W RGBA 4-in-1 COB LED
Beam Angle: 80 Degrees (Opitional 40° & 50°
Lenses Included)
Working Position: Any safe working position
Power Draw: 132W
Power Cord Daisy Chain: 5 Fixtures Max.
Fuse: 3 Amp
Weight: 9 lbs./ 4.1Kgs.
Dimensions: 16.25” (L) x 9.75” (W) x 7.5” (H)
415 x 245 x 192mm
Colors: RGBA Mixing
DMX Channels: 7 DMX Modes: 3 Channel Mode,
4 Channel Mode, 5 Channel Mode,
6 Channel Mode, 7 Channel Mode,
9 Channel Mode, & 10 Channel
Mode
Warranty: 2 Year (730 days)
COB Cannon Wash Pearl
Auto Sensing Voltage: This xture contains a automatic volt-
age switch, which will auto sense the voltage when it is plugged
into the power source.
Please Note: Specications and improvements in the design of
this unit and this manual are subject to change without any prior
written notice.
ADJ Products, LLC
6122 S. Eastern Ave. Los Angeles, CA 90040 USA
Tel: 323-582-2650 / Fax: 323-725-6100
Web: www.adj.com / E-mail: info@americandj.com
ADJ Products, LLC - www.adj.com - COB Cannon Wash Pearl User Manual Page 30
A.D.J. Supply Europe B.V.
Junostraat 2
6468 EW Kerkrade
The Netherlands
service@adjgroup.eu / www.adj.eu
Tel: +31 45 546 85 00 / Fax: +31 45 546 85 99
Loading...